EPM9560RC240-15YY - MAX 9000 CPLD 560 Macrocells | Intel | 240-RQFP
MPN: EPM9560RC240-15YY ✗ انتهى عمره الإنتاجيEPM9560RC240-15YY نظرة عامة
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines multiple PAL/GAL-style AND/OR arrays with a central interconnect matrix. Within the broader taxonomy it sits as a sibling to the FPGA (Field-Programmable Gate Array); CPLDs are deterministic, low-power, and pin-for-pin predictable, while FPGAs are LUT-based and higher density. CPLDs belong to the family of programmable logic devices, which themselves are a sub-category of digital semiconductors used for glue logic, bus interfacing, and state-machine replacement.
Key features include in-system programmability via the IEEE 1149.1 (JTAG) interface, a 5.0 V single-supply core, pin-compatible speed-grade options (-10, -12, -15), and MultiVolt I/O supporting mixed 5 V / 3.3 V signalling. The MAX 9000A architecture uses Logic Array Blocks (LABs) tied together by a programmable interconnect array (PIA), providing deterministic 15 ns pin-to-pin timing across all 560 macrocells with no routing-induced jitter.
Typical applications include high-speed glue logic for 32-bit microprocessors, bus arbitration and interface bridging (PCI, ISA, VME), peripheral controllers, and digital state-machine replacement in telecommunications and industrial control. The wide 191-I/O count also suits multi-channel buffer/driver consolidation and large address-decoder functions.
When designing with this device, observe the 5 V VCC requirement and ensure JTAG chain integrity if multiple devices are cascaded. Decoupling requires 0.1 uF ceramic capacitors close to each VCC/GND pair, with a bulk tantalum or ceramic capacitor on each supply plane. Programming uses the IEEE 1149.1 boundary-scan chain and is supported by Altera/Intel Quartus and legacy MAX+PLUS II tools.
This page synthesizes distributor pricing, drop-in same-package alternatives from the MAX 9000 family, and practical design notes not collected in any single manufacturer document.
بدائل مباشرة لـ EPM9560RC240-15YY — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع EPM9560RC240-15YY (نفس عامل الشكل والبصمة) — يختلف في Package, Family, Device Type, Operating Temperature, User I/O Pins.
EPM9560RC240-15
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM9560RC240-15W
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM9560RC240-15N
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM9560RC240-15C
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM9560RC240-12
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM9560ARC240-10
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←EPM9560RC240-15YY الحدود القصوى والخصائص الكهربائية
| Family | MAX 9000A |
| Logic Type | CMOS EEPROM-based CPLD |
| Number of Macrocells | 560 |
| Usable Gates | 12,000 |
| Number of User I/O | 191 |
| Maximum Operating Frequency | 117.6 MHz |
| Propagation Delay (tpd) | 15 ns |
| Supply Voltage (VCC) | 5.0 V |
| Programmability | In-system via IEEE 1149.1 (JTAG) |
| Package Type | RQFP-240 (Plastic Quad Flat Pack) |
| نوع التركيب | Surface Mount |
| درجة حرارة التشغيل | 0 C to +70 C (commercial) |
| Speed Grade | -15 |
| حالة RoHS | Non-RoHS (YY suffix indicates non-compliant / matte tin or SnPb lead finish per Altera legacy convention) |
دليل تكوين أطراف EPM9560RC240-15YY rqfp-240 (plastic quad flat pack)
تكوين الأطراف لـ EPM9560RC240-15YY (حزمة rqfp-240 (plastic quad flat pack)). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ EPM9560RC240-15YY.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
EPM9560RC240-15YY مناسب لـ 6 التطبيقs: 32-bit Microprocessor Glue Logic, PCI / VME Bus Bridge, Industrial Control State Machine, Peripheral Controller Hub, Address Decoder / Chip-Select Generator, Legacy Telecom Line Card.
32-bit Microprocessor Glue Logic
The EPM9560RC240-15YY is well suited for 32-bit microprocessor glue logic because its 560 macrocells and 191 user I/Os deliver enough capacity to consolidate dozens of 74-series decoder, latch, and bus-driver chips into one CPLD. The deterministic 15 ns pin-to-pin propagation delay matches 50-66 MHz system buses without timing-closure issues, and the JTAG (IEEE 1149.1) interface allows in-system reconfiguration. Place the part between the CPU and memory/peripheral bus to consolidate address decoding, wait-state generation, and chip-select logic; expect 60-70% board-area reduction compared to discrete PAL implementations.
موصى به
PCI / VME Bus Bridge
The EPM9560RC240-15YY serves as a PCI-to-local bus or VME bus bridge because the 191 I/O count and 5 V MultiVolt interface directly drive 32-bit PCI signalling at 33 MHz. Its 560 macrocells hold full PCI target-state machines, parity generation, and interrupt-acknowledge logic in a single device, while the deterministic 15 ns tpd meets PCI 2.1 tVAL timing without wait states. Use the JTAG chain to in-system update bridge firmware; ensure trace impedance of 65 ohms +/- 10% for the PCI segment.
موصى به
Industrial Control State Machine
The EPM9560RC240-15YY is a strong fit for industrial state-machine controllers due to its 560 macrocells supporting 50-100 states with combinational and registered outputs, plus 191 I/Os for sensor and actuator interfacing. The 5 V core and 0-70 C commercial temperature range suit factory-floor cabinets; for harsher environments use the EPM9560RC240-15C industrial-temperature variant. The deterministic 15 ns tpd eliminates race conditions in sequential logic, a key advantage over microcontrollers with interrupt latency.
موصى به
Peripheral Controller Hub
The EPM9560RC240-15YY can replace multiple PAL/GAL devices in peripheral hubs (USB, SCSI, IDE) because its 12,000-gate capacity and 191 I/Os allow channel multiplexing, command decoding, and DMA handshaking in a single chip. The 5 V tolerance on every I/O pin interfaces directly with legacy 5 V peripherals without level shifters. Power consumption is approximately 1.5-2 W at full toggle rate; provide at least 4 layer PCB with dedicated ground plane.
موصى به
Address Decoder / Chip-Select Generator
The EPM9560RC240-15YY excels at large address-decoding tasks (e.g., 32-bit systems needing 20+ chip selects) because each macrocell delivers a product term with up to 36 inputs, far more than discrete 22V10 PALs. The 15 ns tpd means the decoded chip-select arrives well within typical CPU access times. Place the part adjacent to the memory bus to minimize trace delay. The JTAG ISP allows last-minute address-map adjustments without board rework.
موصى به
Legacy Telecom Line Card
The EPM9560RC240-15YY is commonly found in legacy telecom line cards for T1/E1 framers, HDLC controllers, and time-slot interchangers. Its 560 macrocells consolidate framing, alarm, and switching logic that previously required 8-12 discrete PALs, while 5 V tolerance interfaces directly with telecom ASICs of that era. The 15 ns tpd easily handles 1.544/2.048 MHz TDM buses with margin. Note: for new designs, migrate to MAX V 5M570ZE64 or MAX II EPM240 CPLDs.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ EPM9560RC240-15YY — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | EPM9560RC240-15 | EPM9560RC240-15W | EPM9560RC240-15N | EPM9560RC240-15C | EPM9560RC240-12 | EPM9560ARC240-10 |
|---|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | RQFP-240 | RQFP-240 - same | RQFP-240 - same | RQFP-240 - same | RQFP-240 - same | RQFP-240 - same | RQFP-240 - same |
| Macrocells | 560 | 560 | 560 | 560 | 560 | 560 | 560 |
| User I/O | 191 | 191 | 191 | 191 | 191 | 191 | 191 |
| Propagation Delay (tpd) | 15 ns | 15 ns | 15 ns | 15 ns | 15 ns | 12 ns (-20%) | 10 ns (-33%) |
| Maximum Frequency | 117.6 MHz | 117.6 MHz | 117.6 MHz | 117.6 MHz | 117.6 MHz | ~147 MHz (+25%) | ~176 MHz (+50%) |
| Supply Voltage | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| RoHS Compliance | Non-RoHS (YY suffix) | RoHS | RoHS | Pb-free | RoHS (industrial temp) | RoHS | RoHS |
أبرز الفروقات
- Non-RoHS lead finish variant (مقابلEPM9560RC240-15)
- 15 ns deterministic tpd across 560 macrocells (مقابلEPM9560ARC240-10)
- 191 user I/O in RQFP-240 package (مقابلEPM9560RC208-20)
ملاحظات التصميم
The EPM9560RC240-15YY requires a clean 5.0 V VCC supply with +/-5% tolerance. Place a 0.1 uF X7R ceramic decoupling capacitor within 5 mm of every VCC/GND pair (24 VCC pins and 24 GND pins on the RQFP-240). Add a single 22 uF tantalum or 47 uF ceramic bulk capacitor near the package center. Estimated: at 50% toggle rate with 191 I/Os, ICC core current is approximately 300-400 mA, so budget 2-2.5 W worst-case dissipation and verify with the actual design toggle activity.
The RQFP-240 package has a 0.5 mm pitch and 32 mm body size; use 4-layer PCB with dedicated ground plane directly beneath the CPLD. All 24 GND pins must be soldered with low-impedance vias to the inner ground plane (at least 2 vias per GND pin). JTAG signals (TDI, TDO, TMS, TCK, TRST) should be routed as a 4-wire chain with 10 kohm pull-ups on TCK/TMS/TDI and a 10 kohm pull-down on TRST to prevent spurious configuration. Reserve a JTAG header even on production boards for in-field ISP.
Do not confuse the EPM9560RC240-15YY (non-RoHS) with the EPM9560RC240-15 (RoHS) - they are pin-compatible but may fail Pb-free reflow profiles if the YY suffix part is used. Also note that the MAX 9000A family is NRND; new designs should migrate to MAX V (5M570ZE64) or MAX II (EPM240) CPLDs, which require Quartus instead of MAX+PLUS II and have different footprints - PCB redesign will be required for the migration.
معلومات الامتثال
YY suffix per Altera legacy ordering convention indicates non-RoHS lead finish (SnPb or matte-tin). Not AEC-Q100 qualified (CPLD, not an automotive-grade part by default). Reach, halogen-free, and conflict-mineral status not stated in available distributor data; marked unknown.
