EPM9560RC240-15YY - MAX 9000 CPLD 560 Macrocells | Intel | 240-RQFP
Référence : EPM9560RC240-15YY ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $95 | $95,00 |
| 10 | $86.5 | $865,00 |
| 100 | $78 | $7 800,00 |
| 500 | $70.25 | $35 125,00 |
| 1 000 | $64.5 | $64 500,00 |
EPM9560RC240-15YY Présentation
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines multiple PAL/GAL-style AND/OR arrays with a central interconnect matrix. Within the broader taxonomy it sits as a sibling to the FPGA (Field-Programmable Gate Array); CPLDs are deterministic, low-power, and pin-for-pin predictable, while FPGAs are LUT-based and higher density. CPLDs belong to the family of programmable logic devices, which themselves are a sub-category of digital semiconductors used for glue logic, bus interfacing, and state-machine replacement.
Key features include in-system programmability via the IEEE 1149.1 (JTAG) interface, a 5.0 V single-supply core, pin-compatible speed-grade options (-10, -12, -15), and MultiVolt I/O supporting mixed 5 V / 3.3 V signalling. The MAX 9000A architecture uses Logic Array Blocks (LABs) tied together by a programmable interconnect array (PIA), providing deterministic 15 ns pin-to-pin timing across all 560 macrocells with no routing-induced jitter.
Typical applications include high-speed glue logic for 32-bit microprocessors, bus arbitration and interface bridging (PCI, ISA, VME), peripheral controllers, and digital state-machine replacement in telecommunications and industrial control. The wide 191-I/O count also suits multi-channel buffer/driver consolidation and large address-decoder functions.
When designing with this device, observe the 5 V VCC requirement and ensure JTAG chain integrity if multiple devices are cascaded. Decoupling requires 0.1 uF ceramic capacitors close to each VCC/GND pair, with a bulk tantalum or ceramic capacitor on each supply plane. Programming uses the IEEE 1149.1 boundary-scan chain and is supported by Altera/Intel Quartus and legacy MAX+PLUS II tools.
This page synthesizes distributor pricing, drop-in same-package alternatives from the MAX 9000 family, and practical design notes not collected in any single manufacturer document.
Alternatives de remplacement direct pour EPM9560RC240-15YY — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec EPM9560RC240-15YY (même facteur de forme et même empreinte) — différant par Package, Family, Device Type, Operating Temperature, User I/O Pins.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
EPM9560RC240-15
✅ Remplacement direct✓ En stock
$174.72 / unité
Voir la fiche technique →EPM9560RC240-15W
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →EPM9560RC240-15N
✅ Remplacement direct✓ En stock
$27.85 / unité
Voir la fiche technique →EPM9560RC240-15C
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →EPM9560RC240-12
✅ Remplacement direct✓ En stock
$9.95 / unité
Voir la fiche technique →EPM9560ARC240-10
✅ Remplacement direct✓ En stock
$28.8 / unité
Voir la fiche technique →EPM9560RC240-15YY Valeurs maximales et caractéristiques électriques
| Family | MAX 9000A |
| Logic Type | CMOS EEPROM-based CPLD |
| Number of Macrocells | 560 |
| Usable Gates | 12,000 |
| Number of User I/O | 191 |
| Maximum Operating Frequency | 117.6 MHz |
| Propagation Delay (tpd) | 15 ns |
| Supply Voltage (VCC) | 5.0 V |
| Programmability | In-system via IEEE 1149.1 (JTAG) |
| Package Type | RQFP-240 (Plastic Quad Flat Pack) |
| Type de montage | Surface Mount |
| Température de fonctionnement | 0 C to +70 C (commercial) |
| Speed Grade | -15 |
| Statut RoHS | Non-RoHS (YY suffix indicates non-compliant / matte tin or SnPb lead finish per Altera legacy convention) |
Guide de configuration des broches du EPM9560RC240-15YY rqfp-240 (plastic quad flat pack)
Configuration des broches du EPM9560RC240-15YY (boîtier rqfp-240 (plastic quad flat pack)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour EPM9560RC240-15YY.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
EPM9560RC240-15YY convient pour 6 applications: 32-bit Microprocessor Glue Logic, PCI / VME Bus Bridge, Industrial Control State Machine, Peripheral Controller Hub, Address Decoder / Chip-Select Generator, Legacy Telecom Line Card.
32-bit Microprocessor Glue Logic
The EPM9560RC240-15YY is well suited for 32-bit microprocessor glue logic because its 560 macrocells and 191 user I/Os deliver enough capacity to consolidate dozens of 74-series decoder, latch, and bus-driver chips into one CPLD. The deterministic 15 ns pin-to-pin propagation delay matches 50-66 MHz system buses without timing-closure issues, and the JTAG (IEEE 1149.1) interface allows in-system reconfiguration. Place the part between the CPU and memory/peripheral bus to consolidate address decoding, wait-state generation, and chip-select logic; expect 60-70% board-area reduction compared to discrete PAL implementations.
Recommandé
PCI / VME Bus Bridge
The EPM9560RC240-15YY serves as a PCI-to-local bus or VME bus bridge because the 191 I/O count and 5 V MultiVolt interface directly drive 32-bit PCI signalling at 33 MHz. Its 560 macrocells hold full PCI target-state machines, parity generation, and interrupt-acknowledge logic in a single device, while the deterministic 15 ns tpd meets PCI 2.1 tVAL timing without wait states. Use the JTAG chain to in-system update bridge firmware; ensure trace impedance of 65 ohms +/- 10% for the PCI segment.
Recommandé
Industrial Control State Machine
The EPM9560RC240-15YY is a strong fit for industrial state-machine controllers due to its 560 macrocells supporting 50-100 states with combinational and registered outputs, plus 191 I/Os for sensor and actuator interfacing. The 5 V core and 0-70 C commercial temperature range suit factory-floor cabinets; for harsher environments use the EPM9560RC240-15C industrial-temperature variant. The deterministic 15 ns tpd eliminates race conditions in sequential logic, a key advantage over microcontrollers with interrupt latency.
Recommandé
Peripheral Controller Hub
The EPM9560RC240-15YY can replace multiple PAL/GAL devices in peripheral hubs (USB, SCSI, IDE) because its 12,000-gate capacity and 191 I/Os allow channel multiplexing, command decoding, and DMA handshaking in a single chip. The 5 V tolerance on every I/O pin interfaces directly with legacy 5 V peripherals without level shifters. Power consumption is approximately 1.5-2 W at full toggle rate; provide at least 4 layer PCB with dedicated ground plane.
Recommandé
Address Decoder / Chip-Select Generator
The EPM9560RC240-15YY excels at large address-decoding tasks (e.g., 32-bit systems needing 20+ chip selects) because each macrocell delivers a product term with up to 36 inputs, far more than discrete 22V10 PALs. The 15 ns tpd means the decoded chip-select arrives well within typical CPU access times. Place the part adjacent to the memory bus to minimize trace delay. The JTAG ISP allows last-minute address-map adjustments without board rework.
Recommandé
Legacy Telecom Line Card
The EPM9560RC240-15YY is commonly found in legacy telecom line cards for T1/E1 framers, HDLC controllers, and time-slot interchangers. Its 560 macrocells consolidate framing, alarm, and switching logic that previously required 8-12 discrete PALs, while 5 V tolerance interfaces directly with telecom ASICs of that era. The 15 ns tpd easily handles 1.544/2.048 MHz TDM buses with margin. Note: for new designs, migrate to MAX V 5M570ZE64 or MAX II EPM240 CPLDs.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour EPM9560RC240-15YY — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | EPM9560RC240-15 | EPM9560RC240-15W | EPM9560RC240-15N | EPM9560RC240-15C | EPM9560RC240-12 | EPM9560ARC240-10 |
|---|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | RQFP-240 | RQFP-240 - same | RQFP-240 - same | RQFP-240 - same | RQFP-240 - same | RQFP-240 - same | RQFP-240 - same |
| Macrocells | 560 | 560 | 560 | 560 | 560 | 560 | 560 |
| User I/O | 191 | 191 | 191 | 191 | 191 | 191 | 191 |
| Propagation Delay (tpd) | 15 ns | 15 ns | 15 ns | 15 ns | 15 ns | 12 ns (-20%) | 10 ns (-33%) |
| Maximum Frequency | 117.6 MHz | 117.6 MHz | 117.6 MHz | 117.6 MHz | 117.6 MHz | ~147 MHz (+25%) | ~176 MHz (+50%) |
| Supply Voltage | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| RoHS Compliance | Non-RoHS (YY suffix) | RoHS | RoHS | Pb-free | RoHS (industrial temp) | RoHS | RoHS |
Principaux différenciateurs
- Non-RoHS lead finish variant (vs EPM9560RC240-15)
- 15 ns deterministic tpd across 560 macrocells (vs EPM9560ARC240-10)
- 191 user I/O in RQFP-240 package (vs EPM9560RC208-20)
Notes de conception
The EPM9560RC240-15YY requires a clean 5.0 V VCC supply with +/-5% tolerance. Place a 0.1 uF X7R ceramic decoupling capacitor within 5 mm of every VCC/GND pair (24 VCC pins and 24 GND pins on the RQFP-240). Add a single 22 uF tantalum or 47 uF ceramic bulk capacitor near the package center. Estimated: at 50% toggle rate with 191 I/Os, ICC core current is approximately 300-400 mA, so budget 2-2.5 W worst-case dissipation and verify with the actual design toggle activity.
The RQFP-240 package has a 0.5 mm pitch and 32 mm body size; use 4-layer PCB with dedicated ground plane directly beneath the CPLD. All 24 GND pins must be soldered with low-impedance vias to the inner ground plane (at least 2 vias per GND pin). JTAG signals (TDI, TDO, TMS, TCK, TRST) should be routed as a 4-wire chain with 10 kohm pull-ups on TCK/TMS/TDI and a 10 kohm pull-down on TRST to prevent spurious configuration. Reserve a JTAG header even on production boards for in-field ISP.
Do not confuse the EPM9560RC240-15YY (non-RoHS) with the EPM9560RC240-15 (RoHS) - they are pin-compatible but may fail Pb-free reflow profiles if the YY suffix part is used. Also note that the MAX 9000A family is NRND; new designs should migrate to MAX V (5M570ZE64) or MAX II (EPM240) CPLDs, which require Quartus instead of MAX+PLUS II and have different footprints - PCB redesign will be required for the migration.
Informations de conformité
YY suffix per Altera legacy ordering convention indicates non-RoHS lead finish (SnPb or matte-tin). Not AEC-Q100 qualified (CPLD, not an automotive-grade part by default). Reach, halogen-free, and conflict-mineral status not stated in available distributor data; marked unknown.
