Products (22,000+)

MKE02Z16VLC2R - 20MHz 16KB Flash ARM Cortex-M0+ MCU | NXP
MKE02Z16VLC2R

MKE02Z16VLC2R - 20MHz 16KB Flash ARM Cortex-M0+ MCU | NXP

The NXP MKE02Z16VLC2R is a 20 MHz 32-bit ARM Cortex-M0+ microcontroller with 16 KB of Flash memory, 2 KB of SRAM, and 28 GPIO in a 32-LQFP package. It belongs to the Kinetis KE02 family, combining a compact general-purpose MCU with communication, timing, control, analog, and power-management peripherals for cost-sensitive embedded designs. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, and peripherals into one device. The ARM Cortex-M0+ core uses a 32-bit architecture and executes compact embedded firmware, while the KE02 family emphasizes low cost, low power, and high robustness. The MKE02Z16VLC2R is positioned as an entry point into NXP's Kinetis E-series portfolio and is identified as pin-compatible with Kinetis E-series devices and the S08P family. Verified features include a 20 MHz operating frequency, 16 KB programmable Flash, 2 KB SRAM, 28 I/O, and connectivity through I2C, SPI, and UART/USART. Listed peripherals include low-voltage detection, pulse-width modulation, and a watchdog timer. Its power-management module supports Run, Wait, and Stop modes, helping conserve energy when the application does not require continuous processing. The KE02 architecture combines a compact Cortex-M0+ core with integrated communication and control resources, reducing external component requirements in compact control boards. Flash supports in-system programming, while SRAM provides working memory for firmware execution. The available I2C, SPI, and serial interfaces allow the MCU to connect sensors, memory, converters, actuators, and human-interface devices without requiring several dedicated interface controllers. Typical uses include industrial control modules, small sensor nodes, building and appliance controllers, compact power converters, communication equipment, and low-cost embedded products. The 32-LQFP package exposes 28 I/O and is suitable for conventional PCB assembly, prototype boards, and automated production lines that require a leaded surface-mount package. Designers should select the MCU according to firmware size, SRAM demand, peripheral requirements, low-power behavior, and operating-temperature limits. If design rules specify automotive qualification or extended environmental ratings, those requirements must be checked separately because the provided data does not establish AEC-Q100 qualification. Validate all pin multiplexing, clock, and peripheral settings against the current manufacturer documentation before release. This product page combines verified manufacturer and distributor information, practical selection guidance, application context, and honest handling of missing technical data. It is intended to help engineers identify whether the MKE02Z16VLC2R fits a new embedded design or an existing 32-LQFP controller platform.

RFQ Contact
MKE02Z16VLC4 - 40MHz 16KB Cortex-M0+ MCU | NXP
MKE02Z16VLC4

MKE02Z16VLC4 - 40MHz 16KB Cortex-M0+ MCU | NXP

The NXP Semiconductors MKE02Z16VLC4 is a 40 MHz Arm Cortex-M0+ Kinetis KE02 microcontroller with 16 KB of Flash memory, 2 KB of SRAM, and integrated analog peripherals in a 32-LQFP 7 x 7 mm package. It supports 3.3 V and 5 V operation and is positioned for cost-sensitive automotive and industrial applications. A microcontroller is an integrated semiconductor that combines a processor core, program memory, data memory, and peripherals on one device. The MKE02Z16VLC4 belongs to the Kinetis E series, a low-cost 32-bit MCU family designed for control-oriented products. Its Arm Cortex-M0+ architecture provides a compact instruction set and efficient interrupt-driven operation without the complexity of a higher-performance processor. The device combines 16 KB Flash for firmware storage with 2 KB SRAM for working memory. This memory balance suits control loops, human-interface functions, communication services, and basic sensing products where code size is more important than a large working-memory pool. Integrated analog functionality further reduces the number of external components required in a typical embedded design. The Kinetis KE02 family emphasizes robustness for electrical-noise environments, with enhanced ESD and EMC performance highlighted for high-reliability applications. Running at 40 MHz gives designers additional timing headroom for periodic sampling, control calculations, serial communication, and background tasks. The 32-LQFP package also exposes more pins than compact small-outline packages, supporting a broader mix of GPIO and peripheral connections. Typical uses include motor and valve controllers, appliance control boards, building equipment, sensor interfaces, automotive body electronics, and compact industrial modules. Its 5 V capability is especially useful where a regulated 5 V rail already exists and converting the system to a lower-voltage architecture would add unnecessary complexity. Designers should budget Flash and SRAM carefully before finalizing firmware, because the 16 KB and 2 KB capacities constrain image size and working buffers. The 32-LQFP footprint also requires adequate copper area and careful decoupling close to the supply pins. Use the manufacturer pin description, package drawing, and reference design guidance when assigning tracks and planning the power network. This product page consolidates the confirmed device characteristics, a qualified same-family replacement, package considerations, application guidance, and selection trade-offs into a concise engineering reference for the MKE02Z16VLC4.

RFQ Contact
MKE02Z16VLD2 - 32-bit Cortex-M0+ 16KB MCU | NXP Semiconductors
MKE02Z16VLD2

MKE02Z16VLD2 - 32-bit Cortex-M0+ 16KB MCU | NXP Semiconductors

The NXP Semiconductors MKE02Z16VLD2 is a 32-bit ARM Cortex-M0+ Kinetis KE02 microcontroller with 16KB Flash, 2KB SRAM, a 20MHz maximum operating frequency, and a 44-LQFP package. It is positioned as a low-cost, robust entry-point microcontroller for embedded control, industrial equipment, automotive electronics, and connected sensing systems. The device uses a 2.5V, 3.3V, or 5V operating supply range and includes analog, communication, timing, and control peripherals for compact embedded designs. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and communication interfaces onto one package. The MKE02Z16VLD2 belongs to the Kinetis E series, where the KE02 family provides an entry-level platform with pin compatibility to the wider Kinetis E series and the S08P 8-bit family. This compatibility makes the device useful when a product needs a scalable migration path between general-purpose 32-bit control and lower-cost embedded architectures. The main feature set includes 16KB of Flash memory, 2KB SRAM, 32-bit processing, and operation up to 20MHz. The verified product information identifies the MCU as automotive-grade, and the NXP family description highlights low-power operation, robustness, analog and communication peripherals, and multiple timing and control resources. These characteristics support designs that require deterministic embedded control without the memory capacity of a larger application processor. The MKE02Z16VLD2 is associated with Kinetis E-series compatibility and is described as pin compatible with Kinetis E-series devices and the S08P family. Its 44-LQFP package provides a larger, leaded footprint than small package options in the same family, which can simplify prototyping, inspection, and assembly processes. The 10mm by 10mm package is also useful where a conventional LQFP is preferred over fine-pitch or leadless packages. Typical applications include automotive body and control modules, industrial automation controllers, sensor hubs, building equipment, consumer accessories, and small embedded systems. The 20MHz Cortex-M0+ core is suitable for real-time control loops, communication protocol handling, and peripheral coordination. The 16KB Flash and 2KB SRAM are appropriate for firmware that requires moderate state retention and compact application code rather than graphical interfaces or large data storage. When designing around the MKE02Z16VLD2, use the manufacturer datasheet for the exact pin assignments, electrical limits, clock configuration, and peripheral multiplexing for the 44-LQFP package. Confirm the device's power-management modes, flash-write voltage range, and communication peripheral availability against the system requirements before PCB release. The datasheet is the appropriate reference for decoupling, programming, reset, and peripheral-connection details. This product page combines the verified NXP specifications, package and memory details, sourcing context, practical application guidance, and same-package replacement analysis. It is intended to help engineers identify whether the MKE02Z16VLD2 fits a low-voltage, moderate-memory embedded-control design before beginning firmware and PCB development.

RFQ Contact
MKE02Z16VLD4 - 40MHz 16KB Flash 44-LQFP Cortex-M0+ MCU | NXP
MKE02Z16VLD4

MKE02Z16VLD4 - 40MHz 16KB Flash 44-LQFP Cortex-M0+ MCU | NXP

The NXP Semiconductors MKE02Z16VLD4 is an ARM Cortex-M0+ Kinetis KE02 series microcontroller operating at up to 40 MHz, with 16 KB of Flash memory and 2 KB of SRAM, housed in a 44-LQFP 10 x 10 mm package. It is designed for cost-sensitive industrial and automotive applications that require a compact 32-bit control platform with integrated analog, communication, timing, and control peripherals. The Kinetis KE02 family combines a 32-bit ARM Cortex-M0+ processor core with low-power operation and enhanced ESD and EMC performance for electrical-noise environments. The MKE02Z16VLD4 provides a balanced combination of 16 KB Flash, 2 KB SRAM, and integrated analog peripherals, making it appropriate for compact embedded controllers, sensor interfaces, communication nodes, and industrial control modules where board space and cost are important constraints. The device includes a 12-bit ADC and a 6-bit ADC according to the product listing information. These conversion resources allow an application to acquire analog process or sensor signals without requiring a separate high-resolution converter. The operating features, package information, and lifecycle information are documented by NXP on the MKE02Z16VLD4 product page, while the DigiKey and Mouser listings identify the device as an ARM Cortex-M0+ Kinetis KE02 microcontroller with 16 KB Flash and a 40 MHz operating frequency. MKE02Z16VLD4 is particularly useful when a design needs a conventional microcontroller footprint, deterministic control, and an integrated analog signal path. The 44-LQFP package exposes the required power, ground, reset, clock, debug, communication, timer, and GPIO resources in a surface-mount format suitable for automated assembly. The 10 x 10 mm outline is larger than the smallest lead-frame packages, but it provides generous pin access and is practical for designs requiring multiple peripheral connections. For a new design, engineers should confirm the exact pin multiplexing, peripheral allocation, clock configuration, and electrical limits against the NXP MKE02Z16VLD4 datasheet before layout release. The 16 KB Flash capacity should be checked against the final firmware image, including bootloader, application code, calibration data, and update logic. The 2 KB SRAM is also an important constraint for buffering, stack usage, and interrupt-driven software architecture. This page combines manufacturer product information, distributor specifications, lifecycle status, package identification, practical application guidance, and pin-compatible alternatives for engineers evaluating the MKE02Z16VLD4 for embedded control platforms.

RFQ Contact
MKE02Z32VFM4 - 40MHz 32KB Cortex-M0+ MCU | NXP
MKE02Z32VFM4

MKE02Z32VFM4 - 40MHz 32KB Cortex-M0+ MCU | NXP

The NXP Semiconductors MKE02Z32VFM4 is a 32-bit Arm Cortex-M0+ Kinetis KE02 microcontroller operating up to 40 MHz, with 32 KB of flash memory and 4 KB of SRAM in a 32-HVQFN (5x5 mm) package. The device supports 3.3 V and 5 V operation and combines a compact general-purpose MCU core with analog, timing, control, and communication peripherals. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The Kinetis KE02 family belongs to the hierarchy of 32-bit microcontrollers, Arm Cortex-M embedded processors, and general-purpose embedded semiconductors. Its combination of 5 V tolerance, flash memory, SRAM, analog functions, and automotive or industrial connectivity makes it suitable for compact control systems that need more capability than a basic 8-bit microcontroller. Key characteristics include a maximum 40 MHz operating frequency, 32 KB of flash, 4 KB of SRAM, and operation from a 3.3 V or 5 V supply. The manufacturer describes the KE02 series as pin compatible with other Kinetis E series devices and the S08P family within compatible package configurations. Its analog and communication resources support applications involving CAN or LIN connectivity, sensor acquisition, motor or actuator control, and general industrial equipment. The Cortex-M0+ architecture provides a 32-bit instruction set while retaining the simplicity and low power profile expected from a cost-sensitive embedded MCU. Flash memory supports in-system firmware storage, while SRAM provides working memory for control loops and peripheral servicing. The 5x5 mm HVQFN package also supports dense PCB layouts, although its exposed-pad construction requires careful thermal-via and solder-layout design. Typical uses include automotive body and control modules, industrial sensor hubs, appliance controllers, small motor-control boards, and CAN or LIN network nodes. Designers evaluating this MCU should verify the exact pin assignment, peripheral configuration, clock requirements, and analog limits in the manufacturer datasheet before finalizing a PCB, especially when replacing a device from another family. For a new board, route the exposed pad to a thermal copper plane with multiple vias and keep sensitive analog inputs away from switching nodes and high-current traces. For a replacement, confirm software startup configuration, pin multiplexing, and communication timing because package fit alone does not guarantee application-level compatibility. This product overview combines the manufacturer identity, package, memory, clock, voltage, and family information with practical replacement and PCB considerations. It also distinguishes confirmed same-family alternatives from options that require additional engineering review before they can be treated as drop-in devices.

RFQ Contact
MKE02Z32VLC2 - 20MHz Cortex-M0+ 32KB MCU | NXP | LQFP-32
MKE02Z32VLC2

MKE02Z32VLC2 - 20MHz Cortex-M0+ 32KB MCU | NXP | LQFP-32

NXP Semiconductors MKE02Z32VLC2 is a 32-bit Arm Cortex-M0+ microcontroller operating up to 20 MHz, with 32 KB of embedded Flash memory and 4 KB of SRAM, housed in a 32-pin LQFP package measuring 7 x 7 mm. The device operates from 2.7 V to 5.5 V and supports an ambient temperature range from -40 °C to 105 °C. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one compact device. The Kinetis KE02 belongs to the microcontroller hierarchy and combines a low-power Arm Cortex-M0+ core with analog, timing, communication, and control peripherals. Its single-cycle 32-bit multiplier and 32-bit architecture provide efficient control processing for compact embedded products. The MKE02Z32VLC2 provides 32 KB of Flash for firmware and 4 KB of SRAM for working data. Its operating frequency of up to 20 MHz gives control loops and communication handlers useful processing headroom without requiring a larger MCU. The 2.7 V to 5.5 V supply range accommodates industrial and automotive-style 5 V systems as well as compatible 3.3 V designs. Integrated peripherals make the KE02 useful for systems that require more than digital GPIO. NXP describes the family with integrated CAN and LIN communication modules and a 12-bit analog-to-digital converter, supporting automotive, industrial, and cost-sensitive embedded-control applications. Flash write operation is also specified across the 2.7 V to 5.5 V supply range. Typical uses include motor and actuator controllers, automotive body and interface modules, industrial sensing nodes, CAN or LIN subnet gateways, and compact consumer appliances. The 32-LQFP package exposes more interface pins than small-surface-mount MCU packages while remaining compatible with automated PCB assembly and inspection. Designers should preserve clean supply routing, provide the required decoupling close to VDD pins, and use the pin-description and electrical-characteristics tables in the manufacturer datasheet when assigning alternate-function pins. Because software, bootloader behavior, and peripheral mapping are device-specific, firmware validation and brownout behavior should be checked against the final system power profile. This product overview combines the MKE02Z32VLC2 architecture, electrical limits, package details, pin-compatible family options, and application guidance. It also organizes replacement selection around the shared 32-LQFP footprint while highlighting memory, frequency, and qualification differences that determine whether a candidate is truly suitable for an existing design.

RFQ Contact
MKE02Z32VLC4 - 40MHz Cortex-M0+ 32KB MCU | NXP
MKE02Z32VLC4

MKE02Z32VLC4 - 40MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKE02Z32VLC4 is a 32-bit ARM Cortex-M0+ microcontroller operating up to 40 MHz, with 32 KB of flash memory, 4 KB of SRAM, and a 3.3 V/5 V operating capability in a 32-pin LQFP package measuring 7 mm × 7 mm. It is designed for cost-sensitive embedded applications that require a compact general-purpose MCU, flexible serial connectivity, and enhanced electrostatic-discharge and electromagnetic-compatibility performance. A microcontroller is a programmable integrated circuit containing a processor core, memory, peripherals, and communication interfaces. Within the semiconductor hierarchy, the MKE02Z32VLC4 belongs to the ARM Cortex-M0+ class of 32-bit embedded processors and the Kinetis KE02 microcontroller family. The KE02 family targets cost-sensitive, high-reliability equipment operating in electrically noisy environments while retaining a compact pin count and conventional embedded-system integration. The principal device characteristics include a 40 MHz Cortex-M0+ core, 32 KB flash, 4 KB SRAM, and a 32-LQFP package. FlexTimer modules support event timing, counting, motor-control-related functions, and periodic signal generation. The device also provides a 5 V-oriented operating configuration and enhanced ESD/EMC characteristics, making it applicable to industrial controls, appliances, access equipment, and compact consumer products where board area and environmental robustness are important. The 32-bit Cortex-M0+ architecture provides a practical balance between processing capability, code efficiency, and implementation complexity. A dedicated flash program area supports firmware storage, while SRAM provides working memory for control loops, communication stacks, and application state. The 7 mm × 7 mm LQFP package exposes 32 pins and is suitable for conventional surface-mount assembly; its relatively large lead pitch also improves inspection and rework compared with fine-pitch leadless packages. Typical uses include industrial motor and relay control, appliance control boards, access-control terminals, lighting controllers, and compact sensor-interface products. The combination of 32 KB flash, 4 KB SRAM, FlexTimer capability, and a 5 V-compatible supply is particularly useful when the design requires deterministic timing and embedded serial interfaces without the memory cost of a higher-end MCU. Design the PCB with short, impedance-conscious paths for clock and communication signals, and provide the decoupling and reset support specified by the manufacturer datasheet. Confirm peripheral pin assignment and multiplexed functions in the pin-description table before finalizing the board because the LQFP footprint offers a fixed set of shared analog, communication, timer, and debug functions. This product overview combines the confirmed device identity, memory configuration, operating frequency, package details, lifecycle position, sourcing information, and practical integration considerations. It also provides pin-compatible alternatives with clearly stated technical differences so engineers can assess replacement risk before changing an approved design.

RFQ Contact
MKE02Z32VLD2 - 20MHz Cortex-M0+ MCU 32KB Flash | NXP
MKE02Z32VLD2

MKE02Z32VLD2 - 20MHz Cortex-M0+ MCU 32KB Flash | NXP

The NXP Semiconductors MKE02Z32VLD2 is a Kinetis KE02 sub-family 32-bit microcontroller built on the Arm Cortex-M0+ core running at up to 20 MHz, with 32 KB flash memory, 4 KB SRAM, and a wide 2.7 V to 5.5 V operating voltage range, housed in a 44-pin LQFP (10 x 10 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripheral functions such as timers, communication interfaces, and analog converters. Within the power-management hierarchy of embedded systems, the Kinetis E series positions the KE02 as the entry point to NXP's 5 V-tolerant, high-robustness MCU portfolio, pin compatible with the wider Kinetis E series and with NXP's legacy 8-bit S08P family, easing migration from 8-bit designs. Key features include the 20 MHz Cortex-M0+ core with a single-cycle 32-bit x 32-bit multiplier, 32 KB of self-programmable flash with a 2.7 V to 5.5 V flash write voltage range, and an ambient temperature range of -40 C to +105 C for demanding industrial environments. Integrated analog and robust 5 V operation eliminate the need for an external level-shifting supply rail, reducing bill-of-materials cost. The KE02 architecture emphasizes robustness: wide-voltage single-supply operation, ESD-hardened I/O structures, and peripheral sets targeted at motor control, power conversion, and human-machine interfaces. The Cortex-M0+ core delivers low power consumption and code density compatible with the existing Arm toolchain ecosystem, including MCUXpresso IDE and Keil MDK. Typical applications include home appliances, industrial motor control, power supplies and battery chargers, and automotive body modules where 5 V robustness and wide temperature range are required. When designing with this device, budget flash and SRAM carefully: 4 KB of SRAM is ample for bare-metal control loops but constrains RTOS or protocol-stack-heavy designs; consider the pin-compatible 64 KB MKE02Z64VLD2 variant for growth headroom. This page synthesizes distributor pricing, same-footprint drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
MKE02Z32VLD4 - 40MHz Cortex-M0+ 32KB MCU | NXP
MKE02Z32VLD4

MKE02Z32VLD4 - 40MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKE02Z32VLD4 is a 32-bit Arm Cortex-M0+ microcontroller with a 40 MHz maximum clock, 32 KB of flash memory, and a 44-pin LQFP package measuring 10 x 10 mm. It belongs to the Kinetis KE02 family and is designed for compact embedded-control systems requiring efficient Cortex-M0+ processing, analog and digital control peripherals, and flexible communication interfaces. A microcontroller is an integrated circuit that combines a processor core, nonvolatile program memory, data memory, and peripherals on one device. In the device hierarchy, a microcontroller is a semiconductor and a programmable embedded-control component. The Arm Cortex-M0+ architecture is designed for compact, energy-efficient systems, while the Kinetis KE02 family integrates control-oriented analog, communication, timing, and general-purpose input-output functions around that core. The principal device parameters are a 40 MHz operating frequency, 32 KB of flash, and 44-pin LQFP packaging. The product listing identifies support for 3.3 V and 5 V operation, giving designers flexibility across common embedded-system supply rails. Its 32-bit architecture and integrated peripherals reduce the need for separate logic devices in cost-sensitive control products. Technical integration is centered on the Arm Cortex-M0+ core, 32 KB of flash program storage, and the Kinetis KE02 peripheral architecture. The 44-pin LQFP provides 44 externally accessible package positions and is available in a tray configuration for automated production. Compared with a smaller microcontroller package, this footprint offers more connection options while retaining through-hole-package inspectability and compatibility with conventional reflow assembly. Typical applications include industrial control modules, motor-control systems, consumer appliances, building equipment, compact sensor nodes, and general-purpose embedded products. The Cortex-M0+ core is appropriate for supervisory control and real-time peripheral coordination, while the analog and communication resources can reduce external component count when the board design follows the manufacturer's reference configuration. The primary design consideration is confirming the complete pin assignment, electrical limits, and peripheral multiplexing in the manufacturer datasheet before schematic capture. Designers should also preserve the recommended power and decoupling structure and verify that all 44 LQFP positions match the PCB footprint before release. This page organizes the exact MKE02Z32VLD4 configuration, a verified same-family drop-in candidate, application guidance, comparison parameters, and practical PCB considerations for faster component selection and design review.

RFQ Contact
MKE02Z32VLH2 - 20MHz Cortex-M0+ 32KB MCU | NXP
MKE02Z32VLH2

MKE02Z32VLH2 - 20MHz Cortex-M0+ 32KB MCU | NXP

The NXP MKE02Z32VLH2 is a 20 MHz ARM Cortex-M0+ Kinetis KE02 microcontroller with 32 KB of Flash memory, 4 KB of SRAM, and a 64-LQFP 10 x 10 mm package. It is an active, general-purpose embedded MCU designed for cost-sensitive control systems that require reliable 5 V operation and compact integration. The device belongs to the Kinetis E microcontroller family and combines a low-power 32-bit architecture with integrated resources for communication, analog measurement, timers, and digital control. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and communication interfaces onto one package. The MKE02Z32VLH2 is specifically a Kinetis KE02 microcontroller, placing it in the ARM Cortex-M0+ class of 32-bit embedded processors. This class targets compact industrial, consumer, and automotive-adjacent products where deterministic control, low power consumption, and broad peripheral integration are more important than high processor throughput or extensive code storage. The principal device characteristics are a 20 MHz Cortex-M0+ core, 32 KB of Flash program memory, and 4 KB of SRAM. Its 64-LQFP package provides 64 external pins and a 10 x 10 mm body size, making it suitable for conventional through-hole assembly and prototype layouts. The Flash write-voltage range of 2.7 V to 5.5 V supports operation from regulated 5 V industrial and automotive-style systems. The manufacturer identifies the part as active and positions KE02 as the entry point to the Kinetis E portfolio. The KE02 architecture is aimed at embedded control workloads that need predictable peripheral operation rather than intensive data processing. Its Cortex-M0+ instruction set provides a 32-bit programming model while maintaining a compact implementation suitable for cost-sensitive systems. The power-management module supports Run, Wait, and Stop operating modes, allowing firmware to reduce activity when the application does not require continuous processing. The 32 KB Flash capacity is sufficient for compact control firmware, boot logic, configuration tables, and peripheral drivers. Typical uses include small motor controllers, appliance controllers, building equipment, industrial sensor nodes, communication interfaces, and compact embedded products. In these systems, the MCU can coordinate analog and digital inputs, drive timers and outputs, and manage communication tasks. A 5 V supply with a 2.7 V to 5.5 V Flash programming range provides compatibility with established industrial control boards, while the 64-LQFP footprint exposes more I/O than small-outline packages and remains practical for hand-soldered prototypes. PCB planning should preserve access to every LQFP pin and provide clean grounding around the power pins. Decoupling capacitors must be placed close to the supply and ground pins, while programming and debug signals should be routed away from noisy motor-drive and switching nodes. Confirm the complete pin assignment, exposed programming functions, and peripheral multiplexing in the manufacturer datasheet before finalizing the schematic or footprint. This product page consolidates the verified device identity, lifecycle state, package information, core and memory specifications, sourcing workflow, replacement assessment, and application-oriented design guidance. It also distinguishes confirmed drop-in options from near relatives with different clock architecture or package options, helping engineers make a defensible PCB and firmware decision before committing to a bill of materials.

RFQ Contact
MKE02Z32VLH4 - 40MHz Cortex-M0+ 32KB MCU | NXP
MKE02Z32VLH4

MKE02Z32VLH4 - 40MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKE02Z32VLH4 is a 32-bit ARM Cortex-M0+ Kinetis KE02 microcontroller operating at up to 40 MHz, with 32 KB of Flash memory and 4 KB of SRAM in a 64-LQFP 10 mm × 10 mm package. Designed for cost-sensitive, high-reliability applications, it combines low-power operating modes with analog and digital peripherals for industrial and automotive designs. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The Kinetis KE02 series occupies the Cortex-M0+ → 32-bit microcontroller → embedded processor → semiconductor hierarchy. Its compact architecture supports embedded control, signal monitoring, communications, and product-control tasks while reducing the component count required around a general-purpose processor. The MKE02Z32VLH4 combines a 40 MHz Cortex-M0+ core with 32 KB of embedded Flash for firmware and 4 KB of SRAM for working data. Its low-power modes are suited to systems that spend substantial time idle or performing low-duty-cycle measurements. The KE02 family also emphasizes enhanced ESD and EMC performance for equipment operating in electrically noisy environments. The device integrates analog, digital, communication, timing, and control peripherals into the same MCU. This integration supports designs that need mixed signal measurements, general-purpose control, and communication functions without relying on several separate discrete components. Flash-backed firmware storage also permits field-configurable behavior and simplifies production programming relative to ROM-only microcontrollers. Typical uses include industrial control modules, motor and actuator controllers, appliance control boards, instrumentation, building equipment, automotive electronic modules, and low-cost sensor nodes. The 64-LQFP package offers enough I/O for external sensing and control while remaining practical for compact industrial electronics. PCB implementation requires careful decoupling, grounding, and assignment of externally connected pins according to the manufacturer pin-description table. Place the required power capacitors beside their associated supply pins and preserve continuous ground-plane return paths. Firmware should use the low-power modes deliberately so peripheral states, interrupt wake-up behavior, and analog settling are validated as a complete system. This product page combines the manufacturer specifications with package, procurement, comparison, and design guidance. It also identifies family alternatives where pin compatibility can be assessed, helping engineers decide when a higher-memory or higher-speed Kinetis E variant is appropriate for a new design.

RFQ Contact
MKE02Z32VQH2 - 20MHz Cortex-M0+ 32KB Flash MCU | NXP
MKE02Z32VQH2

MKE02Z32VQH2 - 20MHz Cortex-M0+ 32KB Flash MCU | NXP

The NXP Semiconductors MKE02Z32VQH2 is a 32-bit Kinetis KE02 microcontroller with a 20 MHz Arm Cortex-M0+ core, 32 KB of flash memory, 4 KB of SRAM, and integrated USB connectivity in a 64-QFP 14 x 14 mm package. It is positioned as an entry-point microcontroller for compact industrial automation and motor-control systems where deterministic embedded control, USB connectivity, and a moderate pin count are required. A microcontroller is the programmable control center of an embedded system. It executes firmware, reads sensors, controls actuators, and manages communications between a product and its operator or host equipment. The Kinetis KE02 family belongs to the hierarchy of Arm Cortex-M microcontrollers, embedded processors, and general-purpose semiconductors. Compared with larger Cortex-M systems, the MKE02Z32VQH2 combines a small 32 KB code-storage budget with a 64-pin package that offers more external I/O than typical compact MCUs. Key characteristics include a 20 MHz operating clock, 32 KB flash organized as 32K x 8, 4 KB SRAM, a 5 V supply-oriented design, and a 64-QFP package. The 64-pin QFP provides a substantial perimeter for digital interfaces, timers, analog inputs, and mixed-signal connections. Its integrated USB connectivity supports designs that need device communication without adding a separate USB controller, while its compact square package remains practical for medium-density control boards. The Arm Cortex-M0+ architecture provides a simple instruction set and efficient event-driven operation, making it suitable for embedded products that perform control tasks rather than intensive computation. With 32 KB of flash and 4 KB of SRAM, firmware must be organized carefully when combining USB code, application logic, communication stacks, and safety functions. The 20 MHz clock provides useful processing headroom for monitoring, debouncing, protocol handling, and motor-control sequencing. Typical uses include industrial sensor nodes, compact motor controllers, USB-connected test equipment, building-control modules, appliance controllers, and low-cost embedded platforms. The 64-QFP footprint is particularly useful when a design needs numerous discrete I/O connections while remaining within the Kinetis E series ecosystem. It can also support USB-to-serial accessories, configuration tools, and portable diagnostic instruments. PCB implementation should follow the exact pin assignment and land pattern in the NXP Kinetis KE02 datasheet. Place decoupling capacitors close to the supply pins, route sensitive analog inputs away from switching nodes, and use the package thermal and power-distribution recommendations to support reliable operation. Confirm programming, debug, clock, USB, and reset connectivity before releasing the PCB artwork. This product resource combines manufacturer specifications, pin-package guidance, application context, structured comparisons, and practical design notes. It is intended to accelerate component selection while preserving the checks required for firmware, PCB, thermal, and lifecycle decisions.

RFQ Contact
MKE02Z32VQH4 - 40MHz Cortex-M0+ 32KB MCU | NXP
MKE02Z32VQH4

MKE02Z32VQH4 - 40MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKE02Z32VQH4 is a 32-bit ARM Cortex-M0+ Kinetis KE02 microcontroller operating up to 40 MHz, with 32 KB of Flash memory and 4 KB of SRAM, housed in a 64-QFP 14 mm x 14 mm package. It is designed for cost-sensitive, high-reliability applications in electrically noisy automotive and industrial environments. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, and peripherals such as timers, serial interfaces, analog blocks, and interrupt-control resources. The Kinetis KE02 family belongs to the broader 32-bit microcontroller hierarchy and combines deterministic control with flexible embedded software. The MKE02Z32VQH4 targets motor-control, general embedded, and industrial applications that require a compact 64-pin solution. The verified product information identifies a 32-bit Cortex-M0+ core, 40 MHz maximum operating frequency, 32 KB Flash, 4 KB SRAM, and a 5 V robust MCU architecture. Its enhanced ESD/EMC performance is intended for high-electrical-noise equipment. The package provides 64 gull-wing terminals, while the QFP form factor supports conventional surface-mount assembly and easier inspection than very fine-pitch packages. NXP describes the KE02 family as a cost-sensitive MCU solution with FlexTimer modules and low-power operating modes. These features support periodic control, motor-control signal generation, communications, and energy-conscious embedded operation. Firmware developers can use the Cortex-M0+ instruction set and integrated peripherals to reduce external component count and consolidate control functions on one device. Typical applications include small motor controllers, industrial sensor nodes, appliance control boards, automotive accessory modules, and low-cost embedded systems. The 40 MHz operating rate supports responsive control-loop execution, while 32 KB Flash provides room for application code and configuration data. The 4 KB SRAM is sufficient for moderate buffering and stack requirements when firmware is kept within verified memory limits. When designing a PCB, confirm every signal, supply, ground, and exposed-package connection against the NXP datasheet and reference manual before layout release. Decoupling, clock stability, motor-power isolation, analog grounding, and ESD protection remain design-specific requirements rather than inferred guarantees. Validate production firmware and electrical performance under the actual noise, temperature, and load conditions. This product record combines verified manufacturer and distributor information, commercial availability data, package characteristics, and design guidance. It is intended to help engineers source the exact MPN and assess it against same-family variants without presenting unverified substitutions as drop-in replacements.

RFQ Contact
MKE02Z64VFM4 - 40MHz Cortex-M0+ MCU | NXP | Industrial Control
MKE02Z64VFM4

MKE02Z64VFM4 - 40MHz Cortex-M0+ MCU | NXP | Industrial Control

NXP Semiconductors MKE02Z64VFM4 is an ARM Cortex-M0+ Kinetis KE02 microcontroller operating at up to 40 MHz, with 64 KB of flash memory, 4 KB of SRAM, and a 32-lead HVQFN package measuring 5 mm by 5 mm. The device targets cost-sensitive industrial and automotive embedded-control systems that require a compact MCU, a 3.3 V or 5 V supply range, and built-in analog and communication resources. A microcontroller is a programmable system-on-chip used to acquire sensor data, execute control algorithms, and communicate with external hardware. The Kinetis KE02 belongs to the Kinetis E series, an entry-level 32-bit MCU portfolio combining an ARM Cortex-M0+ processor, embedded flash, SRAM, analog conversion, timers, communication peripherals, and GPIO in one package. This hierarchy places the device in the broader embedded-processing and industrial-automation categories. Key features include a 32-bit ARM Cortex-M0+ core operating at 40 MHz, 64 KB of program flash, and 4 KB of SRAM. The MCU is offered in a 32-lead HVQFN package with an exposed thermal pad. Its operating supply options include 3.3 V and 5 V systems, while its integrated analog features support industrial designs that need measurement and control functions without excessive external components. The KE02 architecture provides a practical balance of processing performance, memory, and integration for embedded control rather than high-performance computing. A 40 MHz Cortex-M0+ core offers sufficient control-loop and communications bandwidth for sensors, actuators, and compact control panels. The 64 KB flash area provides room for application firmware, while 4 KB of SRAM supports working variables, stacks, and peripheral buffers. Typical uses include factory automation equipment, building controls, appliance controllers, automotive body-control modules, motor-control peripherals, communication gateways, and low-cost embedded instruments. The compact 5 mm by 5 mm footprint makes the MCU suitable for space-constrained assemblies while still providing a practical exposed-pad thermal path. PCB design should preserve the exposed-pad land pattern, connect it to the appropriate ground plane, and place decoupling capacitors close to the supply pins. Firmware development should also account for pin multiplexing and the peripheral assignments shown in the manufacturer pin-description tables rather than treating all general-purpose I/O as equivalent. This product page organizes the NXP MKE02Z64VFM4 specifications, sourcing information, same-package alternatives, application guidance, and design considerations into a compact engineering reference. It also highlights where a lower-memory family member can reduce memory requirements while retaining the same MCU architecture and physical footprint.

RFQ Contact
MKE02Z64VLC2 - 20MHz Cortex-M0+ 64KB Flash MCU | NXP Kinetis
MKE02Z64VLC2

MKE02Z64VLC2 - 20MHz Cortex-M0+ 64KB Flash MCU | NXP Kinetis

The NXP MKE02Z64VLC2 is a Kinetis KE02 sub-family 32-bit Arm Cortex-M0+ microcontroller with 64 KB flash, 4 KB SRAM, and a 20 MHz CPU core, housed in a 32-pin LQFP (7x7 mm) package. It operates from a wide 2.7 V to 5.5 V supply and supports the same voltage range for flash write operations, making it tolerant of industrial 5 V rails and battery transients. An integrated single-cycle 32-bit x 32-bit multiplier and an ambient operating temperature of -40 C to +105 C position this part for robust embedded control. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, peripherals, and I/O. The Cortex-M0+ is the most energy-efficient Arm core for entry-level MCUs, while the Kinetis E series is NXP's 5 V-tolerant, EMC-robust MCU family for white goods, industrial sensors, and automotive body modules. The KE02 is the entry-point sub-family of the Kinetis E family and is pin-compatible with the broader E series and with NXP's legacy 8-bit S08P family, enabling easy migration from older designs. Key features include a 20 MHz Cortex-M0+ core with single-cycle 32-bit x 32-bit hardware multiplier, 64 KB program flash, 4 KB SRAM, an integrated 16-bit ADC, multiple serial communication interfaces (typically UART, SPI, I2C), timers, and a 5 V-tolerant I/O structure. The part supports low-power run, wait, and stop modes, and includes a low-voltage detect / brown-out reset block that holds the part in reset when VDD falls below safe thresholds. Hardware CRC, watchdog, and clock-loss detection improve functional safety at the system level. The KE02 architecture uses a fast Cortex-M0+ core coupled with a multi-layer AHB-Lite bus matrix, giving deterministic interrupt latency for real-time control loops. The flash memory controller and SRAM share a single 32-bit AHB-Lite port, while peripheral bridges expose timers, ADC, and communication modules at a separate bus speed. This split-bus design keeps ADC sampling and PWM switching predictable even when the CPU is servicing interrupts. Typical applications include white-goods motor control (washing machines, dishwashers, small appliances), industrial sensor conditioning, building automation nodes, low-end body-control automotive modules, and HVAC fan/pump control. The wide 5 V tolerance and -40 C to +105 C ambient rating also suit outdoor lighting and smart-meter peripherals. When designing with this part, ensure that the 5 V-tolerant I/O pins do not exceed VDDA + 0.3 V and that decoupling capacitors are placed within 5 mm of each supply pin. For high-noise industrial environments, place a ferrite bead on the analog supply and add an external watchdog supervisor if the application requires a SIL-class safety level. This page synthesizes XAIPART distributor pricing, drop-in Kinetis E alternatives, and practical design notes not collected in the manufacturer datasheet alone.

RFQ Contact
MKE02Z64VLC2557 - 32-bit ARM Cortex-M0+ 64KB Flash MCU | NXP
MKE02Z64VLC2557

MKE02Z64VLC2557 - 32-bit ARM Cortex-M0+ 64KB Flash MCU | NXP

The NXP MKE02Z64VLC2557 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KE02 sub-family, integrating 64 KB of Flash memory in a 32-pin LQFP (7x7 mm) package. It operates up to 20 MHz core frequency, includes up to 4 KB of SRAM, and is designed for cost-sensitive industrial and consumer embedded applications where deterministic Cortex-M0+ performance and small footprint matter. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals (timers, ADCs, communication interfaces, GPIOs) on a single die. MCUs sit at the bottom of the embedded-computing hierarchy: MCU -> microcontroller -> embedded processor -> semiconductor IC. The Cortex-M0+ core is the smallest and most energy-efficient member of the ARM Cortex-M family, designed for deterministic interrupt response and ultra-low active/standby power - features that make it the de facto choice for battery-operated sensor nodes and small appliance controllers. Key features of the MKE02Z64VLC2557 include the ARM Cortex-M0+ core, 64 KB on-chip Flash, 4 KB SRAM, multiple low-power modes (Wait, Stop), and an internal clock source that allows operation without external crystals. The 32-pin LQFP (7x7) package gives designers 28 usable GPIO lines, ample for keypad scanning, LED drivers, and serial-bridge designs. The wide operating voltage range (typically 2.7 V to 5.5 V for the KE02 family) supports both 3.3 V and 5 V system rails, simplifying industrial designs. The Kinetis KE02 sub-family uses the Cortex-M0+ v0 architecture with a 2-stage pipeline, single-cycle 32x32 hardware multiply, and the standard ARM Cortex-M NVIC for interrupt handling. On-chip peripherals include multiple UART, SPI, and I2C modules, a 12-bit ADC, and FlexTimer/PWM modules suitable for motor control loops. The device's deterministic interrupt latency and atomic bit-banding make firmware development simpler compared to 8-bit legacy MCUs. Typical applications include home appliances (washing-machine user interfaces, induction-cooker control boards), small motor control (BLDC fans, low-power pumps), sensor interface modules, and industrial controllers that have historically used 8-bit MCUs. The KE02's 5 V tolerance on key pins also makes it a popular upgrade path for legacy 8051 designs. When designing with the MKE02Z64VLC2557, ensure the VDDA pin is decoupled with a 100 nF + 1 uF pair placed close to the package, and that the RESET pin has the proper 10 kohm pull-up. The internal clock source can remove the cost of an external crystal in cost-sensitive designs, but for timing-critical peripherals (UART, PWM) the external reference is recommended. This page synthesizes distributor pricing, lifecycle status, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
MKE02Z64VLD2 - 20MHz Cortex-M0+ MCU, 64KB Flash, 44-LQFP | NXP
MKE02Z64VLD2

MKE02Z64VLD2 - 20MHz Cortex-M0+ MCU, 64KB Flash, 44-LQFP | NXP

The NXP MKE02Z64VLD2 is an ARM Cortex-M0+ microcontroller from the Kinetis KE02 sub-family, delivering 20 MHz CPU performance with 64 KB of embedded flash and 4 KB of SRAM in a 44-pin LQFP (10x10 mm) package. As the entry-point to the Kinetis E series portfolio, it is pin-compatible with the rest of the Kinetis E series and with the legacy 8-bit S08P family, simplifying upgrades from existing designs. It operates across a 2.7 V to 5.5 V supply range, supporting both 3.3 V and 5 V rails typical in industrial and cost-sensitive automotive nodes. What is a Kinetis KE02 microcontroller? A Kinetis KE02 MCU is part of NXP's Kinetis E series of 32-bit ARM Cortex-M0+ microcontrollers designed for cost-sensitive, 5 V-tolerant, robust applications. In the taxonomy it falls under microcontroller -> 32-bit MCU -> ARM Cortex-M0+ MCU -> Kinetis E series -> KE02 sub-family. It is engineered for harsh electrical environments (high EMI, wide temperature range, brown-out immunity), making it a workhorse for appliance, industrial control, sensor interface, and automotive body-class applications. Key features include 64 KB on-chip flash, 4 KB SRAM, a 20 MHz Cortex-M0+ core, an internal clock with multiple power modes (Run, Wait, Stop), a 12-bit ADC, timers, PWM, and communication peripherals including UART, SPI, and I2C. The 5 V-tolerant I/O simplifies interfacing to legacy analog and power components without level shifters. Architecturally, the KE02 leverages an ARM Cortex-M0+ core with a Von-Neumann bus and a flash write voltage range of 2.7 V to 5.5 V. The Power Management Module (PMC) integrates three low-power modes to optimize energy efficiency in battery-powered or energy-starved nodes. Robust peripherals are tuned for industrial-grade EMC and ESD performance. Typical applications include industrial sensor hubs, automotive body and lighting controllers, white goods and major-appliance motor control (BLDC/PMSM), HVAC controllers, and low-cost IoT edge nodes. The wide-supply 5 V tolerance makes it well-suited for retrofit 5 V designs dominated by analog sensor front-ends. For designers, verify that your required peripheral set (ADC channels, timer/PWM count, communication port count) matches the LQFP-44 pinout before reuse; the KE02 sub-family offers variants with differing peripheral mixes in the same package. When migrating to a higher flash variant, the KE02Z64 footprint stays the same and the firmware platform remains binary-compatible.

RFQ Contact
MKE02Z64VLD4 - 40MHz Cortex-M0+ 64KB MCU | NXP | Automotive
MKE02Z64VLD4

MKE02Z64VLD4 - 40MHz Cortex-M0+ 64KB MCU | NXP | Automotive

NXP Semiconductors MKE02Z64VLD4 is a 40 MHz ARM Cortex-M0+ Kinetis KE02 microcontroller with 64 KB flash, 4 KB SRAM, integrated analog, and automotive body-control positioning in a 44-LQFP 10 mm by 10 mm package. The device combines a 32-bit processor, flexible memory, and mixed-signal peripherals in a compact surface-mount package suited to cost-sensitive, electrically noisy automotive systems. Its 3.3 V and 5 V operating capability and enhanced ESD and EMC performance make it a practical choice for body electronics, relay drivers, sensing modules, and compact actuator controllers. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals such as timers, communication interfaces, analog converters, and digital I/O into one device. The Kinetis KE02 belongs to the 32-bit microcontroller hierarchy and uses the ARM Cortex-M0+ architecture. This instruction set is designed for efficient embedded control, combining low power consumption, compact code execution, and a broad peripheral mix without requiring an external processor, memory, and support devices. The MKE02Z64VLD4 provides 64 KB of flash for program storage and 4 KB of SRAM for working memory. Its 40 MHz Cortex-M0+ core supports responsive control tasks, while integrated analog reduces the component count for designs that measure analog signals or use PWM-based actuator control. The Kinetis KE02 family targets automotive body applications, including functions where a compact, robust controller is more appropriate than a higher-performance application processor. Operation from a 5 V rail simplifies compatibility with automotive body electrical systems. The device uses an internal clocking system with an internal FLL and a 31.25 kHz pre-trimmed internal reference, together with a 1 kHz low-power oscillator. These clock resources support both performance-oriented control and reduced-power operating modes. The family is positioned for applications that require deterministic peripheral operation, broad I/O availability, and resistance to high electrical-noise environments. Exact conversion performance, timer specifications, and electrical limits must be confirmed in the manufacturer datasheet before final circuit design. Typical uses include automotive body-control modules, window-lift and door-lock controllers, seat and lighting control, small motor drivers, sensor-conditioning nodes, and industrial motor-control products sharing the Kinetis KE02 peripheral architecture. Its 44-LQFP package provides enough pins for external interfaces and mixed-signal connections while remaining compatible with conventional automotive-board manufacturing processes. The same family is also used for cost-sensitive industrial applications requiring low-power 8-bit-class functionality with a 32-bit architecture. PCB design should preserve the datasheet-defined power, ground, decoupling, clock, and programming connections. Place the required supply capacitors close to the device, provide adequate low-impedance ground distribution, and route exposed or high-energy signals away from sensitive analog inputs. The 10 mm by 10 mm LQFP geometry also requires checking paste volume, solder-joint inspection criteria, and assembly-profile clearance against the board outline and neighboring components. This page combines the NXP product identity, package and memory characteristics, replacement options, and implementation guidance into a compact engineering reference. It helps designers evaluate the MKE02Z64VLD4 for 40 MHz embedded control while distinguishing verified same-package alternatives from merely similar automotive microcontrollers that require different footprints or software adaptation.

RFQ Contact
MKE02Z64VLH4 - 40MHz Cortex-M0+ MCU with 64KB Flash | NXP
MKE02Z64VLH4

MKE02Z64VLH4 - 40MHz Cortex-M0+ MCU with 64KB Flash | NXP

The NXP Semiconductors MKE02Z64VLH4 is a 32-bit Arm Cortex-M0+ Kinetis KE02 microcontroller operating up to 40 MHz, with 64 KB of embedded flash, 4 KB of SRAM, and a 64-pin LQFP package measuring 10 mm by 10 mm. It is designed for cost-sensitive motor-control and industrial systems that require deterministic control performance, integrated analog resources, and enhanced robustness in electrically noisy environments. A microcontroller is a programmable system-on-chip that combines a processor core, memory, and dedicated peripherals on one semiconductor device. The Kinetis KE02 family belongs to the broader hierarchy of embedded-system controllers, combining general-purpose processing with timers, communication interfaces, analog conversion, and control-oriented I/O. Its Cortex-M0+ architecture is designed for compact, energy-efficient control tasks rather than high-performance computing or complex graphical workloads. The MKE02Z64VLH4 provides 64 KB of flash for firmware and 4 KB of SRAM for working data. Its maximum 40 MHz operating frequency supports deterministic control-loop execution, while the integrated analog resources reduce the need for external converters in measurement and actuation systems. The NXP KE02 family also includes one 12-bit successive-approximation ADC, two 6-bit DAC channels, 57 general-purpose I/O pins, and communication and timing peripherals for motor-control and industrial equipment. The device is positioned for robust, cost-sensitive embedded control rather than high-end connectivity. Its integrated analog functions support sensor acquisition, monitoring, and simple signal generation, while its timer and communication resources allow it to coordinate actuators and external controllers. The 64-LQFP package provides enough pins for discrete motor-driver interfaces, sensors, communications, and power-management signals without requiring the fine pitch of an advanced BGA package. Typical uses include industrial motor controllers, compact power converters, sensing modules, appliance controls, and embedded automation products. The 40 MHz Cortex-M0+ core can execute control software while the ADC and DAC support feedback loops, diagnostics, and analog set points. The 64 KB flash and 4 KB RAM are sufficient for focused embedded applications where deterministic timing and peripheral integration matter more than large application storage. When laying out a board, route analog and digital return currents carefully, place decoupling capacitors close to the supply pins, and protect externally accessible interfaces from electrical transients. Validate motor and industrial environments against the device's detailed absolute maximum ratings, ESD performance, and operating-temperature limits before releasing the final design. This page combines the MKE02Z64VLH4's key electrical characteristics, verified pin-compatible alternatives, application guidance, package information, and design considerations to support faster component selection and PCB planning.

RFQ Contact
MKE02Z64VQH2557 - 20MHz Cortex-M0+ 64KB MCU | NXP
MKE02Z64VQH2557

MKE02Z64VQH2557 - 20MHz Cortex-M0+ 64KB MCU | NXP

The NXP Semiconductors MKE02Z64VQH2557 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KE02 family, running at up to 20 MHz with 64 KB of flash program memory, 57 general-purpose I/O lines, and a 10-bit ADC, housed in a 64-pin LQFP (QFP, 14x14 mm, 0.8 mm pitch) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals into one chip, forming the lowest tier of the embedded-processor hierarchy (MCU -> embedded processor -> microprocessor -> system-on-chip). The Kinetis KE02 sub-family is NXP's entry point into 32-bit embedded control, designed to replace 8-bit MCUs such as the HC08 and S08 families while pin-preserving migration paths exist within NXP's portfolio. Key features of the MKE02Z64VQH2557 include the ultra-low-power Cortex-M0+ core with its two-stage pipeline and high code density, 64 KB of on-chip flash memory, a wide 2.7V to 5.5V supply range with 3.3V nominal operation, multiple PWM channels for motor and power control, and an integrated 10-bit ADC. The 57 configurable I/O lines provide substantial connectivity for a 64-pin device. Technically, the KE02 family targets cost-sensitive, noisy electrical environments such as home appliances and industrial power conversion. NXP engineered the family with enhanced ESD and EMI robustness, and the wide voltage range allows direct operation from rectified mains-derived supplies or industrial rails without a dedicated regulator stage. The CMOS process keeps quiescent consumption low, and multiple low-power modes support battery-adjacent designs. Typical applications include small motor control (fans, pumps, BLDC drivers), AC-induction and universal-motor control in white goods, power supplies and battery chargers with PWM control loops, digital power conversion, and industrial sensing nodes that need an ADC plus robust I/O. For design-in, note that the 20 MHz core frequency bounds the arithmetic throughput, so timing-critical control loops should be validated at worst-case clock tolerance; the 10-bit ADC resolution is adequate for PWM-based power control but not precision instrumentation. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, with prices as of 2026-10-18.

RFQ Contact
MKE04Z64VLD4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKE04Z64VLD4

MKE04Z64VLD4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP Semiconductors MKE04Z64VLD4 is a 32-bit Kinetis KE04 microcontroller built around a 48 MHz Arm Cortex-M0+ core, with 64 KB of flash memory and 8 KB of SRAM in a 44-LQFP 10 x 10 mm package. It is positioned for cost-sensitive automotive, industrial, and high-reliability applications operating in electrically noisy environments. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile working memory, and peripherals into one device. The Kinetis KE04 family belongs to the broader hierarchy of embedded controllers: Arm Cortex-M0+ core, 32-bit microcontroller, embedded system controller, and general-purpose semiconductor. This combination provides more processing capability than an 8-bit MCU while retaining a simple, deterministic architecture suited to embedded control. The MKE04Z64VLD4 provides 64 KB of flash for firmware, 8 KB of SRAM for data and working variables, and a maximum CPU frequency of 48 MHz. Its Kinetis E-series design emphasizes cost-sensitive operation, robust behavior, and enhanced ESD and EMC performance. The 5 V operating capability and integrated analog peripherals are useful in systems that combine digital control with sensor acquisition, actuator supervision, and communication functions. The Cortex-M0+ processor uses an Arm Thumb instruction set and supports a compact, low-cost embedded architecture. The microcontroller integrates on-chip flash, SRAM, clocking, timers, and analog peripherals into a single package, reducing external component count in compact control boards. Its 44-LQFP package also provides enough lead pitch and exposed perimeter access for economical manufacturing processes that do not use the smallest fine-pitch packages. Typical uses include automotive body and control modules, industrial sensors, motor-control boards, appliance controllers, compact instrumentation, and cost-sensitive embedded products. It is particularly appropriate when a product needs more than an 8-bit processor but can use a single 64 KB flash microcontroller instead of a higher-memory or more complex processor platform. The most important PCB decision is to follow the NXP 44-LQFP pin assignment and land pattern exactly. Confirm the power, ground, decoupling, programming, clock, reset, and analog-pin connections against the manufacturer datasheet before layout release. Keep the decoupling network and exposed-package thermal design suitable for the board's environmental requirements. This page combines verified product characteristics, package and memory details, same-family alternatives, comparison tables, and engineering guidance to help designers select the MKE04Z64VLD4 for embedded automotive, industrial, and cost-sensitive control designs.

RFQ Contact
MKE04Z64VLH4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKE04Z64VLH4

MKE04Z64VLH4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP Semiconductors MKE04Z64VLH4 is a 32-bit Kinetis KE04 microcontroller built around a 48 MHz Arm Cortex-M0+ processor, with 64 KB of flash memory and a 64-LQFP 10 x 10 mm package. It operates from a 3.3 V or 5 V supply and targets cost-sensitive industrial equipment requiring enhanced ESD and EMC performance in electrically noisy environments. A microcontroller is a programmable semiconductor that integrates a CPU, memory, and peripherals into one device. The Kinetis KE04 belongs to the Kinetis E series and combines an Arm Cortex-M0+ processor with embedded flash, SRAM, GPIO, timers, serial interfaces, and analog peripherals. This combination provides a compact platform for motor control, appliance control, industrial interfaces, and embedded measurement systems. The principal specifications include a 48 MHz maximum CPU frequency, 64 KB of programmable flash, an operating supply identified as 3.3 V or 5 V, and a 64-pin LQFP package. The KE04 family also emphasizes enhanced ESD and EMC behavior for cost-sensitive, high-reliability applications. NXP identifies the MKE04Z64VLH4 as an active part, supporting lifecycle planning for new and existing industrial designs. The Arm Cortex-M0+ architecture uses a compact instruction set optimized for embedded control while retaining the software ecosystem associated with Arm processors. The 64 KB flash region provides room for application code, configuration data, and boot logic. Peripheral integration reduces the number of discrete devices required for sensing, timing, communications, and general-purpose I/O, helping simplify board layouts in space-constrained equipment. Typical uses include industrial control panels, motor-control subsystems, appliance controllers, building equipment, sensor-hub boards, and compact consumer products. The 10 x 10 mm LQFP package is easy to inspect and assemble, while the Cortex-M0+ platform supports event-driven firmware for responsive control without requiring a high-power processor. Design the PCB with the manufacturer pin-assignment table as the controlling reference for GPIO multiplexing and alternate functions. Confirm the exact SRAM configuration, peripheral set, operating-temperature limits, clock tolerances, and decoupling requirements in the manufacturer datasheet before schematic release. The tray packaging designation should be checked against the assembly process and incoming-inventory plan. This product page combines the manufacturer device information with practical procurement, application, and design guidance. It also distinguishes the exact MKE04Z64VLH4 order code from documented related variants and clearly identifies the electrical details that still require confirmation from the full manufacturer datasheet.

RFQ Contact
MKE04Z64VLK4 - 48MHz Cortex-M0+ MCU 64KB Flash LQFP-80 | NXP (Tape & Reel)
MKE04Z64VLK4

MKE04Z64VLK4 - 48MHz Cortex-M0+ MCU 64KB Flash LQFP-80 | NXP (Tape & Reel)

The NXP MKE04Z64VLK4 is a Kinetis KE04 family microcontroller built on the ARM Cortex-M0+ core running at 48 MHz, integrating 64 KB of flash program memory and 8 KB of SRAM in an 80-pin LQFP package. It is part of NXP's Kinetis E series designed for cost-sensitive, high-reliability applications in electrically noisy industrial and consumer environments, offering enhanced ESD/EMC robustness versus general-purpose Cortex-M0+ devices. What is a Cortex-M0+ microcontroller? The Cortex-M0+ is ARM's smallest and most energy-efficient 32-bit microcontroller core, designed for embedded systems that require deterministic real-time response, low power consumption, and a simple instruction set. An MCU (microcontroller) integrates a CPU core, program flash, SRAM, and peripherals (analog, timers, communication) into a single chip. The KE04 family sits at the low end of the Kinetis portfolio, optimized for 5 V-tolerant I/O and high-noise immunity rather than maximum performance - it competes in the same space as small PIC, AVR, and ST Cortex-M0 parts. Key features of the MKE04Z64VLK4 include 71 GPIO pins, an integrated 5 V regulator on the internal rail, multiple timers (FTM, LPTMR, PIT), up to two SPI, two I2C, and up to three UART peripherals, a 12-bit ADC, and an internal clock source with FLL trimming. The 5 V-tolerant I/O and ESD/EMC hardening make it suitable for white goods, motor control boards, and factory automation endpoints where the system is exposed to switching transients and discharge events. Architecturally, the KE04 combines a 2-stage Cortex-M0+ pipeline with a single 32-bit flash controller and a peripheral bridge exposing the Kinetis peripheral set to the core. The 80-LQFP footprint (14x14 mm) provides sufficient pin count for full peripheral breakout while remaining hand-solderable for prototype work. Typical applications include BLDC and stepper motor controllers in appliances, industrial sensor interfaces, HVAC control boards, low-end point-of-sale terminals, and any 5 V system replacing legacy 8-bit designs. The wide supply range and integrated analog simplify design-in versus discrete solutions. When designing with this part, ensure your SWD/JTAG header is brought out to a standardized 2x5 0.05" connector to allow field firmware updates. Designers familiar with other Kinetis parts will recognize the peripheral set; KE04 differs from KE02 mainly in flash density and ADC channel count. This page synthesizes distributor pricing, drop-in alternatives (including same-package KE-series variants and cross-package KE04 pinouts), and practical design notes not found in the standard NXP product brief.

RFQ Contact
MKE04Z64VLK4R - 48MHz Cortex-M0+ MCU 64KB Flash LQFP-80 | NXP
MKE04Z64VLK4R

MKE04Z64VLK4R - 48MHz Cortex-M0+ MCU 64KB Flash LQFP-80 | NXP

The NXP MKE04Z64VLK4R is a Kinetis KE04 family microcontroller built on the ARM Cortex-M0+ core running at 48 MHz, integrating 64 KB of flash program memory and 8 KB of SRAM in an 80-pin LQFP package. It is part of NXP's Kinetis E series designed for cost-sensitive, high-reliability applications in electrically noisy industrial and consumer environments, offering enhanced ESD/EMC robustness versus general-purpose Cortex-M0+ devices. What is a Cortex-M0+ microcontroller? The Cortex-M0+ is ARM's smallest and most energy-efficient 32-bit microcontroller core, designed for embedded systems that require deterministic real-time response, low power consumption, and a simple instruction set. An MCU (microcontroller) integrates a CPU core, program flash, SRAM, and peripherals (analog, timers, communication) into a single chip. The KE04 family sits at the low end of the Kinetis portfolio, optimized for 5 V-tolerant I/O and high-noise immunity rather than maximum performance - it competes in the same space as small PIC, AVR, and ST Cortex-M0 parts. Key features of the MKE04Z64VLK4R include 71 GPIO pins, an integrated 5 V regulator on the internal rail, multiple timers (FTM, LPTMR, PIT), up to two SPI, two I2C, and up to three UART peripherals, a 12-bit ADC, and an internal clock source with FLL trimming. The 5 V-tolerant I/O and ESD/EMC hardening make it suitable for white goods, motor control boards, and factory automation endpoints where the system is exposed to switching transients and discharge events. Architecturally, the KE04 combines a 2-stage Cortex-M0+ pipeline with a single 32-bit flash controller and a peripheral bridge exposing the Kinetis peripheral set to the core. The 80-LQFP footprint (14x14 mm) provides sufficient pin count for full peripheral breakout while remaining hand-solderable for prototype work. Typical applications include BLDC and stepper motor controllers in appliances, industrial sensor interfaces, HVAC control boards, low-end point-of-sale terminals, and any 5 V system replacing legacy 8-bit designs. The wide supply range and integrated analog simplify design-in versus discrete solutions. When designing with this part, ensure your SWD/JTAG header is brought out to a standardized 2x5 0.05" connector to allow field firmware updates. Designers familiar with other Kinetis parts will recognize the peripheral set; KE04 differs from KE02 mainly in flash density and ADC channel count. This page synthesizes distributor pricing, drop-in alternatives (including same-package KE-series variants and cross-package KE04 pinouts), and practical design notes not found in the standard NXP product brief.

RFQ Contact