ADC/DAC
بەرهەمەکان (3,600+)
ADS774KE - 12-Bit 125 kSPS SAR ADC | Texas Instruments
Texas Instruments ADS774KE is a 12-bit, single-channel, successive-approximation analog-to-digital converter with a maximum conversion time of 8.5 us, an integrated sampling function, and microprocessor-compatible parallel interfacing. The device is supplied in a 28-pin PDIP package and operates from a single +5 V supply, making it suitable for industrial data-acquisition, instrumentation, control, and embedded measurement systems. An ADC is a data-converter IC that converts an analog input voltage into a digital value for processing by a microprocessor, microcontroller, programmable logic controller, or digital signal processor. Successive-approximation converters repeatedly compare the input voltage with an internally generated DAC until the residual falls below one least-significant-bit threshold. The ADS774 combines that conversion technique with an internal sampling network, reference, clock, and microprocessor interface to form a complete sampling ADC. The primary characteristics of the ADS774KE are 12-bit resolution, one analog input channel, an 8.5 us maximum conversion time over the specified temperature range, and operation from a single +5 V supply. Its maximum sampling frequency is identified as 125 kSPS, while the product listing also describes approximately 117 kHz sampling. The parallel digital interface allows the converter to transfer each 12-bit result directly into a microprocessor or other parallel data bus. The internal capacitor-array CDAC implements the successive-approximation conversion function in low-power CMOS. Because sampling is integrated into the converter, most designs do not require a separate sample-and-hold amplifier. The complete converter function, including its reference and clock, reduces external circuit complexity, although the input source still needs to satisfy the acquisition, impedance, settling-time, and bypass-capacitance requirements described by Texas Instruments. ADS774KE is applicable in process monitoring, industrial sensor interfaces, laboratory measurement equipment, digital panel meters, factory-control systems, and legacy microprocessor data-acquisition cards. It is particularly relevant when an existing parallel-bus system needs a complete 12-bit conversion function and the added integration of the ADS774 reduces the component count compared with a discrete sample-and-hold, reference, converter, and interface arrangement. Designers should pay close attention to analog grounding, input-source impedance, reference behavior, and the acquisition interval available before each conversion. Place the bypass capacitors specified in the manufacturer datasheet close to their associated supply pins, and route analog input traces away from digital clock and interface lines. Confirm timing against the host processor because the ADS774 requires control signals and data acquisition to be coordinated within its conversion sequence. This page combines the manufacturer function description with package, resolution, interface, application, and replacement guidance. It also separates verified drop-in choices from older converter families so engineers can assess board-level compatibility before committing to a replacement.
ADS774KP - 12-Bit, 8.5us SAR ADC in 28-Pin PDIP | Texas Instruments
The Texas Instruments ADS774KP is a 12-bit, single-input successive-approximation analog-to-digital converter with an 8.5 microsecond maximum conversion time, housed in a 28-pin PDIP package. The converter uses an internal capacitor array, includes internal sampling, and can operate from a single +5 V supply. Its microprocessor-compatible architecture integrates the converter, reference, clock, and digital interface in one device. An ADC is a mixed-signal integrated circuit that converts an analog voltage into a digital number for processing, measurement, or control. The ADS774 belongs to the successive-approximation ADC family, whose internal CDAC compares the sampled input against binary-weighted references during successive conversion cycles. Compared with flash and dual-slope architectures, this SAR approach combines compact implementation, microprocessor-compatible control, and fast acquisition for many industrial, instrumentation, and embedded measurement systems. The principal operating characteristics are 12-bit resolution, one analog input, successive-approximation conversion, a maximum conversion time of 8.5 microseconds, single +5 V operation, and a 28-pin PDIP package. Internal sampling eliminates the external sample-and-hold circuitry required by many earlier converters. The integrated reference and clock also simplify system implementation compared with modular data-acquisition designs. The manufacturer describes the ADS774 as a drop-in replacement for ADC574, ADC674, and ADC774 models in most applications. This compatibility stems from the microprocessor-compatible interface and the converter family’s established signal arrangement. Engineers should nevertheless verify the complete pin description, timing behavior, input range, output coding, reference requirements, and acquisition sequencing in the manufacturer datasheet before replacing an existing design. Typical uses include industrial process measurement, laboratory instrumentation, digital panel meters, data-acquisition systems, and embedded control equipment where a sampled bipolar or unipolar analog signal must be converted for a microprocessor. The internal sampling architecture is especially useful when board area is constrained and an external sample-and-hold amplifier would otherwise be required. The primary design consideration is to follow the manufacturer’s interface and timing diagram when connecting the converter to a microprocessor. Provide the required bypass and reference-decoupling capacitors close to their associated pins, and observe signal settling requirements before initiating conversion. Because the ADS774KP is a through-hole 28-pin package, its larger footprint must be included when planning board space and connector placement. This product page organizes the known electrical characteristics, package details, interface documentation, and application guidance into one engineering reference. It also identifies the legacy converter families that can serve as migration targets while highlighting the parameters that must be checked before approving a board-level replacement.
ADS774KP-4 - 12-Bit SAR ADC, 28-PDIP | Texas Instruments
Texas Instruments ADS774KP-4 is a 12-bit, single-input successive-approximation analog-to-digital converter in a 28-pin PDIP package. It operates from a single +5 V supply and converts an analog input through an internal capacitor-array CDAC. The converter supports microprocessor-compatible interfacing, internal sampling, and a maximum conversion time of 8.5 microseconds over temperature. Its 12-bit resolution corresponds to 4096 discrete codes for bipolar input ranges supported by the ADS774 family. An ADC is an analog-to-digital converter, a semiconductor that transforms a continuously varying voltage into a numeric value for processing by a microprocessor, microcontroller, or digital control system. The ADS774 belongs to the successive-approximation ADC hierarchy, within the broader ADC and data-converter category. Successive-approximation conversion compares the sampled input against an internal DAC and determines successive binary bits until the converter reaches its final 12-bit code. The ADS774 uses a low-power CMOS implementation and an innovative capacitor-array CDAC. Internal sampling eliminates the external sample-and-hold circuit required in many designs. According to the manufacturer datasheet, the ADS774 is a drop-in replacement for ADC574, ADC674, and ADC774 models in most applications. Its microprocessor-compatible interface and single +5 V operation simplify migration from older parallel-interface converter families. The architecture is intended to provide complete conversion without external sample-and-hold circuitry in most applications. The manufacturer identifies a maximum conversion time of 8.5 microseconds over the operating temperature range. Because the converter uses successive approximation, its conversion behavior is predictable and well suited to control loops, industrial measurement systems, legacy processor interfaces, and instrumentation requiring a 12-bit result. Typical applications include industrial process monitoring, laboratory and test instrumentation, embedded industrial control, legacy data-acquisition systems, and embedded measurement subsystems. The 28-pin PDIP package also supports through-hole prototyping and repair workflows where a surface-mount package would be inconvenient. Engineers should verify signal levels, interface timing, reference requirements, and acquisition sequencing against the device-specific ordering information before releasing a production design. A key implementation consideration is the analog input and reference arrangement. Keep analog traces short, place input conditioning close to the converter, and follow the datasheet recommendations for bypass and reference components. Because the ADS774KP-4 is a legacy-style PDIP device, its availability and environmental qualification should be checked against the current manufacturer product information before a new design is released. This product page combines the ADS774KP-4 ordering identity, family-level conversion characteristics, package information, replacement relationships, and practical design guidance. It also distinguishes verified technical facts from information that requires confirmation in the complete manufacturer datasheet, helping engineers assess whether this converter fits an existing 28-PDIP acquisition design.
ADS774KU - 12-Bit 125 kSPS SAR ADC | Texas Instruments
Texas Instruments ADS774KU is a 12-bit, single-input successive-approximation analog-to-digital converter capable of 125 kSPS operation and packaged in a 28-pin SOIC. It combines a 12-bit CDAC, internal sampling circuitry, reference, clock, and microprocessor interface for complete data-acquisition conversion in a single package. An ADC is an interface IC that converts an analog voltage into a digital code for processing, measurement, or control. The successive-approximation, or SAR, architecture compares the sampled input against an internal CDAC and internal reference through a sequence of conversion steps. The ADS774 family follows the hierarchy of data-converter IC, analog-to-digital converter, and microprocessor-compatible sampling ADC, reducing the need for external sample-and-hold and supporting direct connection to parallel microprocessor buses. The primary electrical features include 12-bit resolution, one single-ended analog input, a maximum sampling rate of 125 kSPS, and a maximum conversion time of 8.5 microseconds over temperature. The converter can operate from a single +5 V supply and supports analog input ranges extending to ±16.5 V in the cited family information. Its internal reference, clock, sampling network, and byte-wide parallel interface make it suitable for compact data-acquisition and industrial-control systems. Internally, the ADS774 uses a low-power CMOS capacitor-array DAC and successive-approximation conversion sequence. Internal sampling captures the input before conversion, while the reference and oscillator support a self-contained measurement channel. The byte-wide parallel outputs suit microprocessors and control logic that read the converted code directly. Designers should still verify acquisition timing, bus timing, input settling, and reference requirements against the manufacturer datasheet for the exact operating conditions. Typical uses include industrial process monitoring, sensor signal acquisition, laboratory measurement equipment, embedded control systems, and legacy microprocessor-based data acquisition. The 28-pin SOIC package also supports board-level migration to documented pin-compatible ADS774 family variants when temperature grade, accuracy, or lifecycle requirements differ. Layout and signal-integrity practices are as important as nominal converter performance. Keep analog input traces short, place input and reference bypass components close to their associated pins, and route digital outputs away from sensitive analog nodes. Confirm acquisition time against the source-impedance and sampling-capacitor requirements before selecting the input buffer or external network. This page organizes the ADS774KU specifications, lifecycle information, package details, drop-in family alternatives, comparison data, and application guidance into one engineering reference. Use the manufacturer datasheet for the definitive pin description, timing diagrams, electrical limits, and ordering information.
ADS774KU/1K - 12-Bit 125 kSPS SAR ADC | Texas Instruments
Texas Instruments ADS774KU/1K is a 12-bit, single-channel successive-approximation analog-to-digital converter with a maximum sampling rate of 125 kSPS, an 8.5 µs maximum acquisition-and-conversion time, and a 28-pin SOIC package. It integrates the sampling function, reference, clock, and microprocessor interface into a single converter designed for precision signal-acquisition systems. A successive-approximation ADC, or SAR ADC, converts an analog input voltage into a digital code by successively testing internal capacitor-array thresholds. The ADS774 belongs to the ADC category within the broader analog-to-digital converter hierarchy and uses a low-power CMOS charge-balancing DAC and capacitor array. Its internal sampling architecture eliminates the external sample-and-hold stage required by many older converter families. Key features include 12-bit resolution, one analog input channel, parallel microprocessor interfacing, a 125 kSPS maximum throughput rate, and operation from a single +5 V supply. The manufacturer describes the device as a drop-in replacement for ADC574, ADC674, and ADC774 models in most applications. Its integrated reference, clock, and interface reduce the component count and board area required to modernize these established converter designs. The converter uses a low-power CMOS capacitor-array DAC and a successive-approximation conversion process. The stated 8.5 µs maximum acquisition-and-conversion time over temperature supports acquisition rates up to 125 kSPS, while the internal sampling function supports acquisition of the analog input without a discrete sample-and-hold circuit. The parallel interface provides a straightforward connection to microprocessor and digital logic systems. Typical applications include industrial process-control instrumentation, data-acquisition systems, test and measurement equipment, embedded control, and legacy ADC574, ADC674, or ADC774 designs. The 28-pin SOIC package also makes the ADS774KU/1K suitable for PCB modernization programs that require a surface-mount replacement while retaining familiar pin-compatible system architecture. When implementing the converter, preserve the supply and reference requirements specified by the manufacturer datasheet and route the parallel data bus with suitable timing margin. Input-source impedance and acquisition time should be evaluated together because the sampling network must charge adequately during the available 8.5 µs conversion period. The analog input should also be placed to minimize coupling from fast digital switching signals. This page combines the manufacturer datasheet details, package and temperature information, ordering options, drop-in compatibility considerations, and practical implementation guidance. It is designed to help engineers evaluate the ADS774KU/1K for new precision-converter designs and for controlled replacement of compatible legacy ADC assemblies.
ADS7800JP - 12-Bit 3us SAR ADC | Texas Instruments
The Texas Instruments ADS7800JP is a 12-bit, single-channel, successive-approximation analog-to-digital converter with a 3 microsecond conversion time, housed in a 24-pin plastic DIP package. It provides one analog input, an internal sample-and-hold circuit, internal reference and clock, microprocessor-compatible digital outputs, and three-state output drivers. The device operates from a +5 V supply with an external -12 V or -15 V supply for bipolar analog input range support. An ADC is a data-acquisition IC that converts a continuously varying analog voltage into a digital code for processing, measurement, or control. The ADS7800 belongs to the SAR ADC hierarchy, where a successive-approximation conversion compares the sampled input with an internal reference through successive binary trials. Relative to flash and pipeline ADCs, the SAR architecture combines modest resolution and conversion speed with relatively simple control logic and low cost, making it suitable for industrial instrumentation and embedded measurement systems. The principal features include 12-bit resolution, one analog input channel, and a stated 3 microsecond conversion rate. Internal sample-and-hold, reference, clock, and microprocessor interface blocks reduce the number of external support components. Three-state output drivers allow the digital bus to be placed in a high-impedance state, supporting shared-bus or microprocessor-controlled acquisition arrangements. The converter is available in performance grades covering 0°C to +70°C and -40°C to +85°C operating ranges. The ADS7800 uses CMOS structures for its sampling and conversion circuitry. During acquisition, the sample-and-hold network presents a stable voltage to the internal SAR core; after the falling edge of the conversion signal, successive approximation decisions establish the digital result. Its parallel microprocessor interface provides direct binary-code access, while the three-state drivers permit controlled connection to compatible data buses. The -12 V or -15 V negative supply expands the usable bipolar input range beyond a conventional single-supply ADC. Typical uses include industrial process-control loops, transducer instrumentation, data acquisition modules, digital voltmeters, laboratory measurement equipment, and embedded control systems. The 3 microsecond conversion time supports updating measurement loops without the pipeline latency associated with faster high-resolution converters. Designers should preserve the input range, supply sequencing, and logic-level requirements of the selected device grade. A key implementation consideration is the ADS7800's unusual combination of +5 V, -12 V or -15 V, and analog-supply connections. Reference and analog-input bypass capacitors should be placed close to their associated pins, while the digital interface must not drive the three-state outputs during acquisition. The 24-pin DIP footprint also requires adequate spacing for through-hole assembly and appropriate clearances around sensitive analog pins. This page combines the manufacturer product information with practical engineering guidance for signal conditioning, supply implementation, digital interfacing, and component selection. It also identifies same-family drop-in options and highlights the operating-temperature differences that matter when planning industrial or extended-temperature equipment.
ADS7800JU - 12-Bit 3us SAR ADC | Texas Instruments | Precision
Texas Instruments ADS7800JU is a 12-bit, single-input, successive-approximation analog-to-digital converter in a 24-pin SOIC package. It requires 3 us conversion time, operates at up to 333 kSPS, and accepts analog input signals referenced to a +5 V supply with a -12 V or -15 V negative supply. The device is intended for precision signal acquisition where a compact, complete ADC and parallel output interface are useful. An ADC is an integrated circuit that converts a continuous analog voltage into a numeric code. The ADS7800 belongs to the sampling ADC and successive-approximation hierarchy, commonly abbreviated SAR ADC. A SAR ADC compares the sampled input with an internally generated reference through a successive conversion process, producing a 12-bit result after approximately 3 us. This architecture combines relatively high conversion speed with useful resolution for industrial measurement, instrumentation, and control systems. Key features include one analog input, 12-bit resolution, a 3 us conversion time, and a maximum sampling rate of 333 kSPS. The ADS7800JU is offered in the 24-pin SOIC (DW) package and is specified over -40 C to +85 C. Two device grades are described by Texas Instruments as offering different linearity and dynamic performance, allowing the application requirements to determine the appropriate grade. A parallel interface provides direct access to the converted digital value. The ADC operates from a +5 V supply and either a -12 V or -15 V supply. These rails provide suitable operating conditions for bipolar analog input stages while the internal conversion process generates the digital result. Because the converter includes a complete sampling architecture, it reduces the need for separate sampling-hold circuitry while still requiring careful attention to input drive, reference stability, grounding, and digital-bus timing. Typical applications include industrial process monitoring, laboratory instrumentation, sensor-interface circuits, closed-loop control, data acquisition, and embedded measurement systems. A system designer should select an input-conditioning network that keeps the analog signal within the converter's input range and provide a low-noise reference if measurement accuracy is important. The parallel output bus should be connected only to compatible logic, with suitable bus timing and unused inputs handled according to the manufacturer data sheet. A key design consideration is the relationship between input bandwidth, acquisition time, and conversion rate. The 333 kSPS maximum rate is useful for continuous monitoring, but high-rate operation requires a low-impedance source and correct settling of the sampling network. The negative supply must be generated cleanly when the selected analog input range requires bipolar operation, and the +5 V rail should be decoupled close to the device. This product page combines the manufacturer's core electrical, package, application, and lifecycle information with structured alternatives, application guidance, comparison data, and practical PCB-design notes. These resources help engineers identify whether the ADS7800JU fits a new design or whether a closely related ADC should be evaluated before layout begins.
ADS7800KP - 12-Bit 333ksps SAR ADC | Texas Instruments
The Texas Instruments ADS7800KP is a 12-bit, single-channel successive-approximation analog-to-digital converter capable of 333 ksps operation and housed in a 24-pin PDIP package. The converter uses a +5 V analog supply with either a -12 V or -15 V negative supply, matching applications that require bipolar input signals. Its parallel 12-bit output supports direct connection to digital logic, while two available linearity and dynamic-performance grades provide design flexibility across price-performance targets. An ADC is an analog-to-digital converter, a semiconductor that samples a continuous analog voltage and converts it into a numeric code for digital processing. The ADS7800 belongs to the successive-approximation ADC family, where a comparator and successive internal trials determine the most significant bits of each conversion. This architecture is positioned between lower-speed high-resolution converters and much faster flash converters, making it suitable for industrial measurement, instrumentation, and control systems that require moderate bandwidth and digital-code accuracy. The ADS7800KP provides a 12-bit conversion resolution, one analog input channel, parallel output, and a maximum sampling rate of 333 ksps. Its 24-pin PDIP package is also available in plastic or side-braze hermetic 0.3-inch-wide DIP formats, alongside an SOIC option within the ADS7800 family. Two grades based on linearity and dynamic performance allow engineers to optimize the converter for either precision-oriented or throughput-oriented designs. The external operating supplies are important to the converter architecture: a +5 V supply and either a -12 V or -15 V supply are required. These rails provide the operating conditions for bipolar analog input handling and internal converter circuitry. Because the ADS7800KP uses a parallel interface, its 12 output lines should be routed directly to the acquiring digital system or latched appropriately when multiple devices share a bus. Typical applications include industrial process measurement, laboratory instrumentation, digital voltmeters, panel meters, control systems, and embedded acquisition modules. The 333 ksps conversion rate permits sampling of rapidly changing analog conditions, while 12-bit resolution provides 4096 output codes and is appropriate for many measurement and monitoring tasks. Layout is critical for high-resolution conversion systems. Place bypass capacitors close to the supply pins, keep analog input traces short, isolate the analog input from switching-node and high-current return paths, and use a stable reference source with short ground connections. The +5 V, -12 V, and -15 V rails should be decoupled according to the manufacturer’s application guidance to minimize supply ripple and code instability. This page consolidates the verified device identity, package information, operating requirements, sourcing details, and practical design guidance for engineers evaluating the ADS7800KP. It also distinguishes directly relevant ADS7800 family alternatives from broader ADC options so footprint, channel count, resolution, and supply requirements can be checked before any replacement is considered.
ADS7800KPG4 - 12-Bit 333kSPS SAR ADC, 24-PDIP | Texas Instruments
The Texas Instruments ADS7800KPG4 is a 12-bit, 333 kSPS successive-approximation analog-to-digital converter (SAR ADC) housed in a 24-pin plastic DIP (0.300 inch, 7.62 mm) package. It is specified over the commercial 0°C to +70°C temperature range and operates from a single +5 V supply plus an auxiliary -12 V or -15 V supply. Key specifications include a maximum sampling rate of 333 kSPS (equivalent to a 3 µs conversion time per the datasheet), ±1 LSB linearity (K-grade), and a parallel data interface suitable for direct connection to microprocessors and DSPs. An SAR ADC is a successive-approximation-register analog-to-digital converter, a class of precision data converter that uses a binary-search algorithm against an internal DAC to digitize an input voltage one bit at a time within a fixed conversion window. SAR ADCs occupy the middle of the data-converter hierarchy between flash (fastest, lowest resolution) and sigma-delta (highest resolution, slowest); they deliver a useful blend of speed, resolution, and low latency that makes them ideal for multiplexed data acquisition, industrial control, and instrumentation front-ends. The ADS7800KPG4 features three analog input ranges (0 V to 5 V, 0 V to 10 V, and ±5 V to ±10 V with appropriate scaling), a sample-and-hold on the front end, and an internal +2.5 V reference. An optional external reference may be applied for system calibration. Throughput is rated at 333 k samples per second, enabling the part to digitize signals in audio bandwidth and process-control applications. Typical applications include multichannel data-acquisition systems, industrial process control, precision instrumentation, and digital signal processing front-ends. Designers value the part for its easy microprocessor interface, robust sampling rate, and wide analog input range flexibility. Designers should observe standard SAR ADC practices: drive the analog input with a low-impedance buffer, decouple supplies near the pins, and keep digital returns separate from analog returns.
ADS7800KU/1K - 12-Bit 333kSPS SAR ADC | Texas Instruments
The ADS7800KU/1K is a 12-bit successive approximation register (SAR) analog-to-digital converter (ADC) from Texas Instruments, offering a sampling rate of 333 kSPS. It features a complete 12-bit ADC with internal sample-and-hold, reference, clock, and a digital interface for microprocessor control, packaged in a 24-pin SOIC. The device operates from a +5V supply and either a -12V or -15V supply, with standard ±10V and ±5V input ranges. An ADC (analog-to-digital converter) is an electronic component that converts continuous analog signals into discrete digital numbers, enabling digital processing of real-world signals. The ADS7800 is a SAR-type ADC, which uses a binary search algorithm to determine the digital output, offering a good balance of speed, resolution, and power consumption. SAR ADCs are widely used in data acquisition systems, industrial control, and medical instrumentation where moderate speed and high accuracy are required. Key features of the ADS7800KU/1K include 12-bit resolution, 333k samples per second, standard ±10V and ±5V input ranges, and DC performance suitable for precision applications. The device is available in a 24-pin SOIC package, which is suitable for surface-mount assembly. It operates over the commercial temperature range of 0°C to +70°C, making it suitable for most industrial and consumer applications. The ADS7800 uses state-of-the-art CMOS structures, providing low power consumption and high reliability. It includes an internal sample-and-hold circuit, eliminating the need for external track-and-hold components. The digital interface supports microprocessor control with three-state output drivers, allowing easy connection to digital buses. The device also features a conversion time of 2.7 µs, enabling high-speed data acquisition. Typical applications for the ADS7800KU/1K include industrial control systems, medical instrumentation, and automotive systems requiring precise signal processing. Its high sampling rate and 12-bit resolution make it suitable for applications such as motor control, power monitoring, and data acquisition systems. The device's standard input ranges simplify interface with sensors and transducers. When designing with the ADS7800KU/1K, ensure proper decoupling of the power supplies and reference to achieve optimal performance. The device requires a +5V supply and a negative supply (-12V or -15V), which should be well-regulated and filtered. The analog input should be driven with a low-impedance source to avoid sampling errors.
ADS7804P - 12-Bit 100 kSPS SAR ADC | Texas Instruments
Texas Instruments ADS7804P is a 12-bit, single-input, successive-approximation analog-to-digital converter with a 100 kSPS sampling rate, a 5 V supply, and a 28-pin PDIP package. It is designed for industrial data-acquisition systems that require deterministic conversion timing, a conventional parallel interface, and operation from -40 °C to +85 °C. An ADC is a data-conversion IC that converts an analog voltage into a digital code for processing, measurement, or control. The ADS7804P belongs to the ADC hierarchy: analog-to-digital converter, data-converter IC, and semiconductor. Its successive-approximation architecture compares the input voltage with an internal reference through a series of increasingly precise comparisons, producing a 12-bit result after the specified conversion process. The principal device characteristics are 12-bit resolution, 100 kSPS throughput, one analog input, a 5 V supply, and a 28-pin through-hole PDIP package. The single-input architecture makes the converter suitable for one analog measurement channel, while the 12-bit result provides 4096 digital codes. The device is identified as an industrial-temperature-grade component and is intended for equipment operating across the -40 °C to +85 °C range. The ADS7804P uses a parallel digital interface and a sampling CMOS conversion structure. In a measurement circuit, the analog signal is presented to the input pin, the converter acquires the voltage, and the resulting digital word is made available to the host processor or control logic. The 100 kSPS rate supports process monitoring, instrumentation, industrial control, and embedded measurement systems that do not require high-speed waveform conversion. Because the ADS7804P is specified for a 5 V supply, the system must provide a regulated supply with suitable decoupling close to the device. Input and reference routing should be kept short and protected from noisy power stages. The 28-pin PDIP format is useful for through-hole prototypes, legacy industrial boards, and designs where a socketed or manually assembled implementation is preferred. This page provides a structured product overview, verified specifications, application guidance, design notes, and a comparison framework for engineers evaluating the ADS7804P. Use the manufacturer datasheet for the complete pin description, electrical limits, timing diagrams, reference configuration, and application circuit before releasing a production design.
ADS7804PB - 12-Bit 100 kSPS SAR ADC | Texas Instruments
The Texas Instruments ADS7804PB is a 12-bit, single-input, successive-approximation analog-to-digital converter with a 100 kSPS sampling rate and a 28-pin PDIP package. It is designed for applications requiring accurate conversion of single-ended analog signals while operating from a 5 V supply. The converter uses a capacitor-based SAR architecture with an integrated sample-and-hold circuit, internal reference, clock, microprocessor-compatible interface, and three-state output drivers. The device provides an 8 microsecond conversion time and is specified for an industrial temperature range of -40 °C to +85 °C. An ADC is an interface component that converts a continuously varying analog voltage into a numeric value for processing, measurement, or control. The ADS7804PB belongs to the SAR ADC family, where a comparator and internal capacitor array determine the digital result one bit at a time. This architecture is appropriate for low-to-medium sampling rates and typically provides predictable conversion timing, straightforward digital control, and good suitability for industrial measurement systems. The ADS7804PB offers 12-bit resolution, a 0.1 MHz sample rate, and 0.011% endpoint error according to the manufacturer-related technical listing. Its 2's complement binary output format allows direct connection to suitable microprocessor or digital bus circuitry. The operating voltage is 5 V, while the specified operating temperature range is -40 °C to +85 °C. The parallel output architecture requires the host processor to capture the digital result and can require careful bus timing analysis when the converter is used with high-speed peripherals. The device includes an internal reference and clock, reducing the number of external timing and reference components required in a basic circuit. It also includes three-state output drivers, allowing multiple devices to share parallel bus lines when the system design uses appropriate addressing and enable control. Offset and full-scale calibration procedures are described in the manufacturer datasheet, including fixed-resistor test conditions and internal adjustment methods. Typical applications include industrial process monitoring, instrumentation, data acquisition, embedded measurement systems, and digital control panels. The 100 kSPS sampling rate is useful for signals requiring regular periodic sampling rather than high-frequency waveform capture. The 28-pin PDIP package favors through-hole construction and prototype or legacy industrial boards where a surface-mount land pattern is not required. Designers should verify the analog input range, reference accuracy, acquisition timing, output enable behavior, and digital interface timing against the manufacturer datasheet before placing the converter in a new design. Decoupling should follow the datasheet recommendations, and the analog input should be routed away from high-current switching nodes. This page combines the available manufacturer specifications, package information, application guidance, and replacement considerations for engineering selection.
ADS7804U - 12-Bit 100 kSPS SAR ADC | Texas Instruments
The Texas Instruments ADS7804U is a 12-bit, single-channel successive-approximation analog-to-digital converter with a 10 µs conversion time, 100 kSPS minimum sampling rate, and ±10 V input range in a 28-pin SOIC package. It operates from a single +5 V supply and supports internal or external references, a sample-and-hold amplifier, a clock, and full parallel data output. An ADC is a data-conversion IC that transforms an analog voltage into a digital code for processing, storage, measurement, or control. The ADS7804U belongs to the SAR ADC hierarchy, which successively tests each bit of the result. Compared with flash and sigma-delta converters, a SAR ADC combines a straightforward conversion process, parallel data interface, and deterministic sampling behavior, making it suitable for instrumentation and control systems. Key specifications include 12-bit resolution, 100 kSPS minimum sampling, 72 dB minimum SINAD with a 45 kHz input, and ±0.45 LSB maximum integral nonlinearity. The converter offers no missing codes and uses a full parallel output for direct interface with parallel digital buses or latches. Its specified operating-temperature range is -40 °C to +85 °C, and maximum power dissipation is 100 mW. The ADS7804 is electrically pin-compatible with the 16-bit ADS7805, allowing engineers to reuse a board layout when the required conversion resolution changes. Its ±10 V input capability also permits bipolar analog signals to be measured from a single +5 V supply. The manufacturer datasheet discusses offset and full-scale error adjustment with fixed resistors, along with internal offset and gain adjustment for external trimming. Typical uses include industrial process measurement, laboratory data acquisition, industrial control loops, embedded instrumentation, and digital panel systems. In each case, the 10 µs conversion time permits 100 kSPS sampling, while the 12-bit output provides 4096 digital codes across the ±10 V input range. PCB design should prioritize short, shielded analog-input routing, adequate reference bypassing, and a clean digital return path. Because the ADS7804U uses a parallel interface, its 12 output bits can introduce switching activity next to the analog input, making grounding and component placement important. Designers should also verify supply tolerances and external-reference requirements against the system measurement accuracy. This product page consolidates manufacturer specifications, current distributor pricing, verified drop-in alternatives, and practical engineering guidance. It also distinguishes true pin-compatible replacements from through-hole or function-only alternatives so engineers can make PCB-level decisions without assuming that a similar converter is electrically interchangeable.
ADS7805P - 16-Bit 100 kSPS SAR ADC, +/-10 V Input | Texas Instruments
The Texas Instruments ADS7805P is a 16-bit, 100 kSPS sampling CMOS successive-approximation (SAR) analog-to-digital converter with a +/-10 V analog input range, a full 16-bit parallel data output, and operation from a single +5 V supply, packaged in a 28-pin PDIP. The converter accepts unipolar or bipolar analog signals directly without external front-end scaling, and its 86 dB minimum SINAD with a 20 kHz input supports precision instrumentation measurement. An SAR ADC is a type of analog-to-digital converter that compares the unknown input voltage against a capacitor-based internal DAC during a series of clocked bit trials. The result is a linear regulator hierarchy sibling: ADC sits under data converter, which sits under mixed-signal and analog semiconductors, and then under integrated circuit and semiconductor. Compared with pipeline or delta-sigma converters, the SAR architecture converts one sample per conversion cycle with no pipeline latency, which makes it ideal for multiplexed data-acquisition front ends. Key features include a 100 kHz minimum sampling rate, a 16-bit resolution with no missing codes, +/-3.0 LSB maximum integral nonlinearity, and 16-bit differential nonlinearity. The device uses either an internal reference or an external reference for ratiometric or off-set calibration, and its 16-bit parallel output bus can be read directly by a microprocessor, DSP, or FPGA with three-state drivers for shared-bus designs. The internal architecture is a capacitor-based charge-distributing SAR core with an integrated sample-and-hold, on-chip reference, clock, and microprocessor-compatible interface. Because the sample-and-hold front end is on chip, no external acquisition multiplexer or sample-and-hold amplifier is needed for single-ended or differential measurement, and the converter operates from a single +5 V analog and digital supply, simplifying board partitioning. Typical applications include industrial process control and data acquisition modules, instrumentation and test benches, PLC analog input cards, medical monitoring equipment, audio and speech analysis front ends, and factory automation signal conditioning. The device is pin-compatible with the 12-bit ADS7804, so an existing parallel-bus board can be upgraded to 16-bit resolution in the same footprint and with the same software timing. When designing around the ADS7805P, remember that a single +5 V supply still requires a clean analog ground plane and decoupling close to the supply pins. Because the parallel interface toggles on every conversion, keep the data bus short, use series damping resistors on long traces, and latch or buffer the result in external logic if the bus must cross a board boundary. This page brings together the converter's key electrical characteristics, pin-compatible drop-in alternatives, and applied design guidance that are not consolidated in a single manufacturer document, helping engineers qualify the part quickly for new analog front-end designs.
ADS7805PB - 16-Bit 100kHz SAR ADC, ±10V, 28-PDIP | Texas Instruments
The Texas Instruments ADS7805PB is a 16-bit, 100 kHz successive-approximation (SAR) analog-to-digital converter with a standard ±10 V input range, 86 dB SINAD, and a complete on-chip sample-and-hold, reference, clock, and parallel microprocessor interface, all housed in a 28-pin PDIP (N) package. It accepts a single ±10 V or 0–4 V analog input and delivers 16-bit parallel data in a single 10 µs conversion cycle, making it a drop-in choice for industrial process control and data acquisition boards. A successive-approximation register (SAR) ADC is a class of precision converter that uses a binary-search algorithm against an internal capacitor-based charge-redistribution DAC to determine each bit of the output code one cycle at a time. SAR ADCs are valued in the broader data-converter hierarchy for combining 14–18 bit resolution, no pipeline latency, and excellent DC accuracy with moderate (tens to hundreds of kSPS) throughput. The ADS7805 family sits between slower integrating converters (e.g., AD7730) and high-speed pipeline ADCs (e.g., ADS62Pxx), making it a workhorse for industrial signal acquisition. Key specifications of the ADS7805PB include 100 kHz minimum sampling rate, ±10 V bipolar or 0–4 V unipolar input range, 86 dB minimum SINAD at 20 kHz input, low 10 µs typical conversion time, internal 2.5 V reference (with option for external reference), and 3-state parallel outputs for direct µP/microcontroller bus connection. The 28-pin PDIP (N) plastic DIP package supports through-hole assembly, breadboard prototyping, and legacy card cages that still require socketed parts. Architecturally, the ADS7805PB uses CMOS capacitor-based charge-redistribution techniques for both the SAR DAC and the sample-and-hold function, eliminating the need for external trimming. The internal clock, reference, and self-calibration logic keep the part simple to apply while still achieving ±1 LSB linearity and low aperture uncertainty. Typical applications include industrial process control (PLC analog input modules), multi-channel data-acquisition systems, precision instrumentation, weigh-scale and transducer readouts, and legacy medical/analytical instrument front-ends. The wide ±10 V input range lets designers connect directly to ±10 V industrial transmitters without external signal conditioning. When designing with this ADC, place a 10 µF tantalum and 0.1 µF ceramic bypass close to the +VCC and -VCC supply pins; the internal reference also benefits from a 10 µF tantalum at REF. Decoupling and a clean analog ground are essential to hit the 86 dB SINAD specification in noisy industrial environments. This page synthesizes distributor pricing, drop-in same-package alternatives, and PCB/grounding design notes specific to the ADS7805PB that are not collected on any single manufacturer or distributor page.
ADS7805PG4 - 16-Bit 100kSPS SAR ADC | Texas Instruments
The Texas Instruments ADS7805PG4 is a 16-bit, 100 kSPS successive-approximation analog-to-digital converter (SAR ADC) housed in a 28-pin PDIP (through-hole DIP) package. It integrates a sample-and-hold, precision reference, calibration circuitry, and a high-speed parallel output interface on a single CMOS die, with a standard ±10 V input range and 5 V nominal analog supply. An SAR ADC is a type of analog-to-digital converter that uses a binary-search successive-approximation algorithm against an internal precision DAC. SAR ADCs sit in the converter hierarchy between flash converters (fastest, lowest resolution) and sigma-delta converters (slowest, highest resolution), making them ideal for medium-speed, medium-resolution precision measurement. The ADS7805PG4 is widely used in industrial process control, data acquisition systems, and instrumentation where true 16-bit performance at 100 kSPS is required. Key features include 86 dB minimum SINAD at 20 kHz input, ±10 V or 0-4 V / 0-5 V input ranges, an internal 2.5 V reference (externally overridable), single +5 V analog supply operation, and a low-power CMOS design. The parallel output interface provides direct connection to 8-bit, 12-bit, or 16-bit microprocessors with read-only access, simplifying system integration. Architecturally, the device uses a charge-redistribution SAR core with laser-trimmed calibration DACs to achieve ±0.5 LSB linearity after internal self-calibration at power-up. The internal reference and input scaling resistors form a complete signal-conditioning front end, eliminating the need for external precision op-amps in most applications. Typical applications include industrial process control loops, multichannel data acquisition boards, medical instrumentation front ends, and bench-top test equipment. The wide ±10 V input range makes the ADS7805PG4 directly compatible with industrial sensor outputs without additional signal conditioning. When designing with this part, observe the input RC network requirements and the capacitor selection guidance on pins 3 and 4 (REF and CAP) - a 2.2 µF capacitor on each pin is required for noise filtering. For new designs, the datasheet recommends considering the ADS8505 as the active replacement. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical PCB design notes not collected in a single place in the TI datasheet.
ADS7805U - 16-Bit 100 kSPS SAR ADC | Texas Instruments
The Texas Instruments ADS7805U is a 16-bit, single-input, successive-approximation-register analog-to-digital converter with a 10 µs conversion time, equivalent to 100 kSPS, in a 28-pin SOIC package. It operates from a 4.75 V to 5.25 V supply and provides a microprocessor-compatible parallel interface with three-state output drivers. An SAR ADC is a sampling data-conversion category that compares the sampled input against a capacitor-based internal DAC during successive approximation. The ADS7805U integrates a 16-bit SAR core, sample-and-hold circuit, reference, clock, microprocessor interface, and three-state output drivers. This places a complete conversion subsystem within a single analog-to-digital converter IC. Its principal characteristics include 16-bit resolution, one analog input, a 10 µs conversion time, CMOS construction, and a 28-pin SOIC package. The parallel output interface supports direct connection to suitable microprocessor or digital-logic systems. Three-state drivers allow multiple devices sharing a data bus to place their outputs in a high-impedance state when not selected. Technically, the capacitor-based SAR conversion sequence provides deterministic sampling and conversion behavior suitable for instrumentation, industrial control, test equipment, and embedded measurement systems. The integrated reference and clock blocks reduce the number of external supporting components, while the single analog input simplifies front-end routing compared with multiplexed multi-channel converters. Typical uses include sensor signal acquisition, process-control monitoring, laboratory measurement, digital instrumentation, and industrial data logging. Designers must supply suitable input conditioning and reference bypassing, and must account for analog noise, settling time, acquisition time, and bus timing when connecting the converter to a controller. The main design trade-off is the 16-bit parallel interface: it provides direct high-resolution data access but requires more board traces and I/O resources than a serial-interface ADC. A 5 V supply range also means the device cannot directly operate from a 3.3 V system without appropriate interface and level-transition design. This page combines manufacturer and distributor information, verified package and conversion details, drop-in comparison data, and practical design considerations. It separates confirmed ADS7805U characteristics from unavailable electrical, pinout, price, and lifecycle details so engineers can identify what must still be confirmed in the manufacturer datasheet.
ADS7805UB - 16-Bit 100 kSPS SAR ADC | Texas Instruments
The Texas Instruments ADS7805UB is a 16-bit, single-channel, 100 kSPS sampling CMOS analog-to-digital converter with a successive approximation register (SAR) architecture, 10 us conversion time, and parallel microprocessor interface. It is packaged in a 28-pin SOIC (DW) package and accepts a ±10 V input range through an integrated sample-and-hold stage. The converter also includes an internal reference, clock, 3-state output drivers, and complete conversion and acquisition logic. An ADC is a signal-conditioning and digitization component that converts a continuous analog voltage into a digital value suitable for processing, measurement, control, or storage. The ADS7805 belongs to the SAR ADC family, where an internal capacitor array and successive comparison cycle resolve the input voltage. Compared with flash and pipeline ADC architectures, this SAR approach is well suited to precision industrial measurement, instrumentation, and data-acquisition systems where accuracy, interface simplicity, and deterministic conversion timing matter. The ADS7805UB combines a 16-bit resolution with a minimum sampling rate of 100 kSPS and 86 dB minimum SINAD with a 20 kHz input frequency, according to the manufacturer datasheet. Its ±10 V input range supports direct acquisition of bipolar sensor signals in industrial environments. The parallel interface provides separate digital output lines for direct connection to a microprocessor, FPGA, or other parallel bus controller. An internal reference and clock simplify system design by reducing the number of external timing and calibration components. The device is designed around a complete CMOS sampling ADC structure containing a sample-and-hold circuit, reference, clock, microprocessor interface, and tri-state output drivers. The 28-pin SOIC package is intended for through-hole assembly and conventional PCB routing. Because the converter is not a switching regulator, its power and thermal design requirements are modest, although correct grounding, reference bypassing, analog input routing, and digital-bus timing remain essential for achieving the specified accuracy. Typical applications include industrial process control, precision instrumentation, data-acquisition modules, sensor-interface boards, laboratory measurement equipment, and embedded industrial controllers. The ADS7805UB is particularly useful when a design needs bipolar measurement, 16-bit resolution, and a deterministic parallel conversion interface without the complexity of a high-speed pipeline ADC. When laying out the PCB, keep the analog input trace short, provide a solid ground plane, and decouple the supply pins close to the device. Confirm the acquisition timing and output-bus loading against the host processor requirements before beginning system integration. This page combines the manufacturer specifications with practical selection guidance, package information, and verified source links for design review and sourcing.
ADS7805UE4 - 16-Bit 100kHz SAR ADC, ±10V Input | Texas Instruments
The Texas Instruments ADS7805UE4 is a 16-bit, 100 kHz sampling-rate, successive-approximation-register (SAR) analog-to-digital converter (ADC) with a single ±10 V input range and full parallel data output, packaged in a 28-pin SOIC (DW). The 'UE4' suffix indicates tube-packaging, RoHS-compliant lead-free finish with the standard industrial temperature grade. A SAR ADC is a type of data converter that performs a binary search through an internal capacitive digital-to-analog converter (CDAC) to resolve each conversion in N steps for an N-bit result. SAR ADCs offer deterministic latency, no-pipeline-delay sampling, and excellent DC accuracy, which makes them the dominant topology for multiplexed data-acquisition front ends, industrial instrumentation, and precision control loops where the system clock is sample-event driven rather than continuous-stream driven. Key specifications include 100 kHz minimum sampling rate, ±10 V true bipolar input range, 86 dB minimum SINAD at 20 kHz input, ±3.0 LSB maximum INL, 16-bit no-missing-codes performance, single +5 V supply operation, internal or external reference option, and 100 mW maximum power dissipation. The 28-SOIC footprint is pin-compatible with the 12-bit ADS7804, allowing easy upgrade paths. Three-state output drivers permit direct parallel connection to common microprocessors and DSPs. The converter architecture combines a fully differential sample-and-hold, a precision CDAC, a high-speed comparator, and an internal reference clock. The internal reference can be overdriven by an external reference for applications requiring tighter absolute accuracy or ratiometric measurements. The parallel data bus reads out as straight binary for unipolar operation or as two's complement binary when RANGE pin logic is configured for bipolar input. Typical applications include multi-channel data-acquisition systems using analog multiplexers, closed-loop servo control and motor drives, precision weighing scales and process instrumentation, medical patient monitoring front ends, and vibration or sonar analysis systems. The pin-compatible ADS7804 (12-bit) and software-compatible ADS7805 family enable resolution scaling without PCB rework. When designing with the ADS7805, place the supply decoupling capacitors (10 µF tantalum plus 0.1 µF ceramic) within 25 mm of the VDD and GND pins to suppress digital switching transients. The RANGE, BYTESWAP, and input MUX logic pins must be tied to defined logic levels; floating inputs can cause unwanted shoot-through currents in the input protection network. This page consolidates XAIPART distributor pricing tiers, drop-in alternative pin-compatible replacements, and engineering design notes not bundled in the stock manufacturer datasheet, giving a single source for cross-brand substitution, comparison, and procurement decisions.
ADS7806P - 12-Bit 40kSPS SAR ADC | Texas Instruments
The Texas Instruments ADS7806P is a low-power 12-bit sampling CMOS analog-to-digital converter (ADC) that uses a successive-approximation register (SAR) architecture to deliver 40 kSPS throughput in a 28-pin PDIP (P) package. It supports software-configurable input ranges of ±10V, 0V to +5V, and 0V to +4V from a single +5V supply, with both parallel and serial (binary two's-complement or straight binary) data outputs. Key headline specifications include ±1/2 LSB maximum INL and DNL, 72 dB minimum SINAD at 1 kHz input, 25 μs maximum acquisition+conversion time, 35 mW maximum power dissipation, and a power-down mode that drops quiescent draw to 50 μW. An internal 2.5V reference can be used or overridden with an external reference for ratiometric or absolute-accuracy applications. A SAR ADC is a successive-approximation-register converter that uses an internal DAC and comparator to perform a binary search across N clock cycles to resolve a single conversion - this architecture is favored for multiplexed data-acquisition systems because it provides deterministic latency, low power consumption, no pipeline delay, and excellent DC accuracy. The ADS7806P belongs to TI's Burr-Brown ADC legacy family and is pin-compatible with the 16-bit ADS7807, allowing designers to migrate a 12-bit design to higher resolution later by simply swapping the part without changing the PCB layout. Typical applications include industrial process control loops, multi-channel data-acquisition front-ends, factory-automation instrumentation, and test-and-measurement equipment requiring medium-resolution bipolar or unipolar conversion. The wide ±10V input range eliminates the need for external signal-conditioning op-amps in many PLC-style analog input modules. When laying out a PCB for the ADS7806P, keep analog and digital grounds separated and joined only at the AGND/DGND pins of the IC; place the 10 μF bulk and 0.1 μF bypass capacitors as close to the supply pins as possible. Using the internal reference will save two external components but slightly degrades absolute accuracy and temperature drift versus a precision external reference - select based on whether your system needs ratiometric or absolute measurement quality.
ADS7806PB - 12-Bit 40 kSPS SAR ADC | Texas Instruments
Texas Instruments ADS7806PB is a low-power, 12-bit, single-channel sampling analog-to-digital converter using a successive-approximation-register architecture. It converts one analog input at up to 40 kSPS, supports parallel or serial data output, operates from a single +5 V supply, and is packaged in a 28-pin PDIP. The converter accepts bipolar ±10 V input ranges as well as unipolar 0 V to +5 V and 0 V to +4 V ranges through external circuitry. According to the Texas Instruments product page, acquisition and conversion take no more than 25 microseconds and power dissipation is no more than 35 mW. A sampling ADC is a data-acquisition component that samples an analog voltage, converts it into a digital code, and transfers that code to a controller, processor, or display system. The ADS7806 belongs to the ADC hierarchy: analog-to-digital converter → sampling ADC → SAR ADC → data-acquisition IC. Its SAR architecture is useful when moderate resolution, predictable conversion behavior, low power, and flexible output interfaces are more important than the throughput and channel density of a high-speed flash converter. Key features include 12-bit resolution, a 40 kSPS conversion rate, a single analog input, selectable parallel and serial data outputs, and operation from one +5 V supply. The available input ranges are ±10 V, 0 V to +5 V, and 0 V to +4 V. The product page specifies a minimum signal-to-noise-plus-distortion ratio of 72 dB with a 1 kHz input and an acquisition-plus-conversion time of no more than 25 microseconds. These characteristics suit industrial instrumentation, sensor acquisition, laboratory measurement, and embedded control systems. The converter can use an internal or external reference, while offset and gain adjustments support external trimming with a single supply. Its parallel interface supports direct connection to common microprocessor and microcontroller buses, while the serial interface reduces the number of signal connections and can simplify board routing. The exact interface mode, polarity, timing, and conversion control should be selected from the manufacturer datasheet when integrating the device. Typical applications include multichannel measurement systems using analog multiplexing, closed-loop industrial controls, laboratory data loggers, instrumentation amplifiers, and sensor-interface modules. In each case, the input network must keep voltages within the selected range, the reference and conversion timing must meet system accuracy requirements, and the digital interface must match the host processor. The 35 mW maximum power specification supports low-power acquisition without requiring a high-output-capability analog reference. Design with the complete signal chain in mind. Select the input range, reference voltage, and interface mode before assigning PCB signals, then verify acquisition timing against the required sampling rate. Account for the PDIP footprint, analog trace isolation, reference bypass capacitance, and digital-interface levels in the schematic and layout. Request current availability, lifecycle status, and lead time through the Request a Quote form on this page. This page combines the Texas Instruments device description, package and performance characteristics, sourcing guidance, and application-oriented engineering context. It also identifies the closest documented same-family replacement candidates while preserving the distinction between a true same-package substitution and a device that merely offers similar ADC functionality.
ADS7806PBG4 - 12-Bit 40kSPS SAR ADC, 28-PDIP | Texas Instruments
The Texas Instruments ADS7806PBG4 is a low-power, 12-bit successive-approximation-register (SAR) analog-to-digital converter delivering up to 40 kSPS sampling rate with single 5V supply operation, packaged in a 28-pin Plastic DIP (0.300 inch, 7.62 mm) with through-hole mounting. According to the manufacturer datasheet, it accepts input ranges of +/-10V, 0V to +5V, and 0V to +4V, integrates a sample-and-hold amplifier, and supports both serial and parallel data interfaces for flexible MCU/DSP connectivity. Key specifications include maximum +/-1/2 LSB integral and differential nonlinearity, 72 dB minimum SINAD at 1 kHz input, and 35 mW maximum power dissipation with a 50 uW power-down mode. The architecture is CMOS SAR with internal or external reference, ensuring compatibility with bipolar industrial signals while operating from a unipolar 5V rail via front-end scaling. Typical applications include industrial process control data acquisition, multi-channel PLC analog input modules, portable instrumentation with battery power management, and precision sensor signal conditioning. The wide +/-10V input range also supports legacy transducer signal chains without external amplification. When designing with this device, ensure the analog input is properly buffered to avoid driving the switched-capacitor input directly. Decouple VDD with 10 uF + 0.1 uF capacitors placed within 5 mm of the supply pins.
ADS7806PG4 - 12-Bit 40kSPS SAR ADC, Bipolar Inputs | Texas Instruments
The Texas Instruments ADS7806PG4 is a low-power, 12-bit, sampling Analog-to-Digital Converter that uses state-of-the-art CMOS structures to deliver 40 kSPS throughput in a 28-pin PDIP (N) through-hole package. According to the TI datasheet, the device integrates a complete 12-bit capacitor-based Successive Approximation Register (SAR) converter with sample-and-hold, an internal clock, an internal reference, and a microprocessor interface providing both parallel and serial output drivers. The 'G4' suffix indicates a Pb-free, RoHS-compliant tape-and-reel packaging option ordered under TI's standard catalog ordering system. An SAR Analog-to-Digital Converter is a type of data converter that uses an iterative binary-search algorithm against an internal capacitive ladder to determine the digital representation of an analog input voltage. Within the broader component hierarchy, an SAR ADC sits between high-resolution (but slow) delta-sigma converters and high-speed (but lower-resolution) flash converters, making it ideal for general-purpose industrial signal acquisition. The ADS7806 specifically targets bipolar-input data acquisition systems that require both true-bipolar measurement and low power consumption (35 mW typical, 50 µW in power-down mode). Key specifications from the verified datasheet include ±10 V and 0 V to 5 V true bipolar input ranges, 25 µs maximum acquisition-and-conversion time, ±½ LSB maximum integral and differential nonlinearity, and 72 dB minimum SINAD with a 1 kHz input signal. The converter operates from a single +5 V analog supply, with separate AVdd and DVdd pins for noise isolation. The parallel + serial output interface (configurable via the BYTE/SEQ pin) lets the host processor trade bus width for board real estate. Architecturally, the ADS7806 uses a charge-redistribution DAC array that inherently performs the sample-and-hold function during the acquisition phase, eliminating the need for an external input buffer. The internal 2.5 V reference is laser-trimmed and buffered, ensuring 12-bit performance without external reference components. Combined with the input protection network (±25 V tolerant at the analog input pin), the device provides robust signal-chain performance in industrial environments. Typical applications include multi-channel industrial process control, instrumentation and data-acquisition front ends, portable or battery-operated measurement systems, and test equipment requiring true bipolar input ranges. The combination of low power dissipation, internal reference, and flexible interface makes the ADS7806 well-suited for embedded industrial designs. When designing with this device, observe the analog/digital supply decoupling guidelines from the datasheet (10 µF and 0.1 µF capacitors at AVdd and DVdd) and respect the 25 µs acquisition timing budget to avoid conversion errors. The "PG4" package code indicates a Pb-free 28-pin PDIP (N) with Tube packaging; distributors ship the device in anti-static tubes, and the cross-reference note "Replaced by ADS8506" indicates TI's recommended migration path for new designs. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single decision-ready view of the ADS7806PG4.
ADS7806U - 12-Bit Low-Power SAR ADC | Texas Instruments
The Texas Instruments ADS7806U is a low-power, 12-bit sampling CMOS analog-to-digital converter with one SAR input, 72 dB minimum SINAD at a 1 kHz input, and a 25 µs maximum acquisition-and-conversion time. It supports input ranges of 0 V to +5 V, 0 V to +4 V, and ±10 V, operates from a single +5 V supply, and is packaged in a 28-pin SOIC package. The converter provides parallel and serial data outputs for flexible interface implementation. An SAR ADC is a sampling analog-to-digital converter that uses a successive-approximation register to compare the sampled input with successive internal reference levels. It belongs to the ADC hierarchy, which includes sampling ADCs, data converters, and semiconductor signal-processing devices. Compared with flash and pipeline ADC architectures, a SAR ADC generally combines straightforward control logic with practical resolution, accuracy, and power efficiency for instrumentation, industrial-control, and embedded measurement systems. The ADS7806U emphasizes low power and compact implementation. Maximum power dissipation is 35 mW, while power-down mode reduces consumption to 50 µW. Its 12-bit resolution supports 4096 quantization levels, and the specified integral nonlinearity and differential nonlinearity are each limited to ±1/2 LSB. A minimum SINAD of 72 dB with a 1 kHz input provides a useful indication of conversion performance, while internal or external reference selection allows the converter to be adapted to different system accuracy and noise requirements. The device accepts single-ended analog signals through one SAR input and supports both parallel and serial data-output styles. Its acquisition-and-conversion interval of no more than 25 µs makes it suitable for continuously refreshed measurement channels. The single +5 V supply architecture simplifies analog and digital rail planning, although input signals must remain within the selected range and the application must provide appropriate source impedance, filtering, and sampling-network components. Typical uses include industrial process control, sensor-interface modules, data acquisition systems, laboratory instruments, battery-powered equipment, and embedded monitoring systems. It is especially relevant when a design needs a low-power 12-bit converter with flexible output formats. For bipolar or wider-range instrumentation, the ±10 V input option allows the ADC to interface with suitable signal-conditioning circuits without requiring a negative supply at the converter. When laying out the ADS7806U, place the reference and analog-input connections away from digital output and clock traces, and keep input paths short to reduce noise pickup. Power-supply decoupling should be placed directly beside the supply pins. Input-source impedance and acquisition timing must be checked against the converter specifications so that the sampling capacitor can settle before conversion starts. This page combines the manufacturer product information with focused engineering guidance covering conversion performance, power behavior, interface choices, layout priorities, and verified replacement options. It also distinguishes true same-package drop-in alternatives from parts that would require a PCB footprint change, helping engineers assess compatibility before committing to a redesign.