بەرهەمەکان (3,600+)

ADS7806U/1K - 12-Bit 40kHz SAR ADC, Parallel/Serial, SOIC-28 | TI
ADS7806U/1K

ADS7806U/1K - 12-Bit 40kHz SAR ADC, Parallel/Serial, SOIC-28 | TI

The Texas Instruments ADS7806U/1K is a low-power, 12-bit, sampling CMOS Analog-to-Digital Converter using a successive-approximation architecture. It supports up to 40 kS/s throughput with a 25 us max acquisition-plus-conversion time, and is housed in a 28-pin SOIC package. An ADC (Analog-to-Digital Converter) is a mixed-signal integrated circuit that quantizes a continuous analog voltage into a discrete digital code. SAR (Successive-Approximation Register) ADCs convert one bit per clock cycle by comparing the input against an internal DAC, making them well suited for medium-speed, medium-resolution data acquisition. The ADS7806 sits in the SAR ADC family -> data acquisition ICs -> mixed-signal ICs -> integrated circuits, offering both parallel and serial data output interfaces. Key features include 35 mW maximum power dissipation, a 50 uW power-down mode for battery-friendly operation, +/-1/2 LSB maximum INL and DNL, and 72 dB minimum SINAD at 1 kHz input. The input range spans 0V to +5V (with software configuration to +/-5V and +/-4V), and the device operates from a single +5V supply. The combination of low power, parallel+serial interface, and single-supply operation makes it a flexible drop-in for embedded data acquisition. The architecture uses a capacitive-charge-distribution DAC with a sample-and-hold front end and an on-chip clock. The conversion is initiated by a CONVST pulse, and the result is available on either the parallel DB0-DB11 bus or a SPI-compatible serial port with internal/external clock option. Hardware byte-select pins let the host read high and low bytes sequentially on the parallel bus. Typical applications include industrial process control, portable instrumentation, data acquisition systems, and battery-powered sensor digitizers. The 50 uW power-down current is critical for handheld medical or field instruments where the ADC is idle most of the time. When designing with this device, ensure the input is within the source-impedance budget specified in the manufacturer datasheet to avoid conversion-time violations; the S/H front end must be fully settled in 25 us. Use a clean +5V analog supply with adequate decoupling, and route digital outputs away from the analog input traces to limit digital feedthrough. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet and distributor listings.

RFQ پەیوەندی
ADS7806U/1KE4 - 12-Bit 40kSPS SAR ADC | Texas Instruments
ADS7806U/1KE4

ADS7806U/1KE4 - 12-Bit 40kSPS SAR ADC | Texas Instruments

The Texas Instruments ADS7806U/1KE4 is a 12-bit, 40 kSPS, single-supply, low-power successive-approximation-register (SAR) analog-to-digital converter housed in a 28-pin SOIC package, designed for industrial-temperature (-40C to +85C) operation. It accepts single-ended input ranges of +/-10 V, 0 V to +5 V, and 0 V to +4 V via pin-strapping, drawing only 35 mW during active conversion and dropping to 50 uW in power-down mode. The device supports both serial and parallel data output, internal or external reference, and delivers 72 dB minimum SINAD with a 1 kHz input. A Successive Approximation Register (SAR) ADC is a converter architecture that internally performs a binary search against the analog input, locking one bit per clock cycle until the final 12-bit code is latched in ~25 us. SAR converters sit within the broader hierarchy of analog-to-digital converters -> data converters -> mixed-signal ICs, and are favoured for applications that need deterministic latency, low latency per conversion, and no pipeline delay - unlike pipelined or delta-sigma ADCs that trade latency for higher speed or resolution. The ADS7806U/1KE4 specifically targets industrial signal chains where 5 V single-supply operation and bipolar-input capability are required. Key specifications include maximum 25 us acquisition-plus-conversion time, +/-1/2 LSB maximum integral non-linearity (INL) and differential non-linearity (DNL), 35 mW typical active power dissipation, and a true-differential sample-and-hold input structure. The converter is pin-compatible with the 16-bit ADS7807, allowing an upgrade path to higher resolution without PCB rework. Parallel-byte, parallel-word, and serial interface modes are user-selectable on start-up pins. The architecture uses a charge-redistribution DAC array, an onboard clock, and a precision reference buffer. An analog input front-end scales +/-10 V signals directly to the internal 0 V-4 V converter range, eliminating external op-amp signal conditioning in most cases. The internal reference is trimmed for low drift, and an external reference pin is also available for applications that require ratiometric measurement or absolute-accuracy calibration. Typical applications include industrial process-control analog input modules, multi-channel data-acquisition systems, portable instrumentation, power-line monitoring, and embedded control loops where 12-bit resolution and bipolar input are sufficient. The SO-28 footprint allows easy layout on 2-layer industrial PCBs. When designing with this device, select the input range by tying RANG pin high or low, and decouple REF with a low-ESR 10 uF ceramic plus 0.1 uF bypass combination. Ensure the RCAP pin is left floating only when using the internal reference. This page synthesises distributor pricing, drop-in TI and cross-brand alternatives, and practical layout notes not found in the manufacturer datasheet alone, giving procurement and design engineers a single decision-ready view of the part.

RFQ پەیوەندی
ADS7806UE4 - 12-Bit 25us SAR ADC, 28-SOIC | Texas Instruments
ADS7806UE4

ADS7806UE4 - 12-Bit 25us SAR ADC, 28-SOIC | Texas Instruments

The Texas Instruments ADS7806UE4 is a 12-bit, low-power, sampling CMOS analog-to-digital converter (ADC) that performs a complete 16-bit-compatible acquisition and conversion cycle in 25 microseconds maximum, housed in a 28-pin SOIC (DW) package. It features one single-ended analog input channel, true 12-bit SAR architecture with internal sample-and-hold, and supports bipolar or unipolar input ranges of ±10V, 0V to +5V, and 0V to +4V from a single +5V supply. Output data is presented through a parallel (DB0-DB11 plus sign) or serial interface, with HW or SW control of the conversion sequence. What is a SAR ADC? A successive-approximation-register (SAR) ADC is a type of analog-to-digital converter that uses an internal comparator, a digital-to-analog converter (DAC), and a successive-approximation register to digitize an analog input one bit at a time. SAR ADCs sit within the broader taxonomy of Nyquist-rate data converters (ADC -> data converter -> mixed-signal IC -> semiconductor) and are valued for deterministic latency, no pipeline delay, and excellent DC accuracy at moderate sampling rates, making them ideal for multiplexed data acquisition and industrial process control. Key features of the ADS7806UE4 include 72 dB minimum SINAD with a 1 kHz input, ±1/2 LSB maximum INL and DNL (no missing codes), an internal or external reference option, and a true single +5V supply operation. Power dissipation is 35 mW maximum during active conversion and drops to just 50 µW in hardware-controlled power-down mode, allowing battery-powered and thermally-constrained systems to manage energy budgets without sacrificing dynamic range. Architecturally, the device uses a charge-redistribution DAC array with a low-noise comparator, laser-trimmed scaling resistors that establish the bipolar and unipolar input ranges, and a flexible serial/parallel digital interface that simplifies connection to microcontrollers, DSPs, and FPGAs. The pin-compatible 16-bit ADS7807 is offered for designs that need higher resolution within the same board layout, and a parallel 16-bit family is also documented in TI's data converter brochure. Typical applications include industrial process control data acquisition boards, portable instrumentation and battery-powered measurement front-ends, medical monitoring equipment front-ends, and multi-channel multiplexed data acquisition subsystems. Design tip: provide a clean +5V analog supply rail with sufficient decoupling near AVDGND, keep the analog input traces short and guarded, and add a small RC at the analog input for op-amp settling when the source impedance exceeds the recommended value. This page synthesizes distributor pricing, drop-in pin-compatible alternatives in the same 28-SOIC footprint, and practical design notes not consolidated on the manufacturer datasheet.

RFQ پەیوەندی
ADS7806UG4 - 12-Bit 40kSPS SAR ADC | Texas Instruments
ADS7806UG4

ADS7806UG4 - 12-Bit 40kSPS SAR ADC | Texas Instruments

The Texas Instruments ADS7806UG4 is a low-power, 12-bit sampling CMOS Analog-to-Digital Converter (ADC) with a successive approximation register (SAR) architecture, offered in a 28-pin SOIC (DW) package. It features a maximum sampling rate of 40 kSPS, ±10V, 0V to +5V, and 0V to +4V true bipolar input ranges, and operates from a single +5V supply while drawing only 35 mW of power (50 µW in power-down mode). Key features include 12-bit resolution with no missing codes, ±1/2 LSB maximum INL and DNL, 72 dB minimum SINAD at a 1 kHz input, internal 2.5V reference (or external reference option), parallel and serial data output drivers, and pin compatibility with the 16-bit ADS7807. The 28-SOIC package allows easy migration to higher resolution within the same footprint. A SAR (Successive Approximation Register) ADC is a precision data-conversion topology that uses a binary-search algorithm against an internal DAC and comparator to digitize an analog input one bit at a time. SAR ADCs sit in the broader hierarchy of: ADC -> data converter -> signal-chain IC -> mixed-signal semiconductor. They are prized for deterministic latency, no-pipeline-delay behavior, and excellent DC accuracy, which is why the ADS7806UG4 remains a popular choice for multiplexed industrial data-acquisition systems. Typical applications include industrial process control, multi-channel data acquisition boards, instrumentation, portable battery-powered measurement, and medical monitoring front-ends. The single +5V supply and software-controlled power-down mode make it well suited for power-sensitive embedded designs. When designing with this device, ensure the analog input is properly buffered and that the SHDN pin is asserted for at least 1 µs to enter power-down. A 10 µF bypass capacitor on REF and 0.1 µF on VDD are recommended for stable conversions. The SAR architecture guarantees zero pipeline delay, simplifying multiplexed sampling. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
ADS7807P - 16-Bit 40kSPS SAR ADC, ±10V Input | Texas Instruments
ADS7807P

ADS7807P - 16-Bit 40kSPS SAR ADC, ±10V Input | Texas Instruments

The Texas Instruments ADS7807P is a 16-bit, low-power, sampling CMOS Analog-to-Digital Converter (ADC) housed in a 28-pin PDIP (0.3-inch DIP-28) package, providing a pin-compatible upgrade path from the 12-bit ADS7806 family. It uses a successive-approximation-register (SAR) architecture with an internal sample-and-hold, clock, reference, and a flexible parallel/serial microprocessor interface. A successive-approximation-register ADC is a converter that performs a binary search against the analog input using an internal DAC, producing a digital output one bit at a time per clock cycle. Within the converter hierarchy, the SAR ADC sits between flash and sigma-delta converters: faster than sigma-delta, lower-power than flash, and ideally suited to multiplexed data-acquisition systems where 12-to-16-bit precision meets 10 kSPS-to-1 MSPS throughput. The ADS7807P occupies the 16-bit, ~40 kSPS node of this spectrum. Key features of the ADS7807P include ±1.5 LSB maximum integral nonlinearity (INL), 16-bit no-missing-codes performance, 86 dB minimum SINAD at a 1 kHz input, and three software-selectable input ranges: ±10 V, 0 V to +5 V, and 0 V to +4 V. Maximum power dissipation is 35 mW, and a hardware- or software-controlled power-down mode drops quiescent consumption to 50 µW, making the part attractive for battery-powered and multiplexed systems. Architecture-wise, the part uses a charge-redistribution CDAC with input transient suppression, internal 2.5 V reference (external override supported), and a single +5 V supply rail. The maximum acquisition-plus-conversion time is 25 µs, supporting a maximum throughput of approximately 40 kSPS in classic parallel mode. Typical applications include industrial process-control front ends, multi-channel data-acquisition boards, portable instrumentation, weigh-scale and sensor-signal digitization, and medical monitoring equipment such as patient-monitoring front ends. When designing with the ADS7807P, pay close attention to the input-protection RC network, keep analog and digital grounds separated at a single star point, and place the supply decoupling capacitors as close to the AVDD/DVDD pins as the PCB layout allows. A logic-low on R/C initiates conversion, and BUSY remains high until data is latched. This page consolidates distributor pricing, drop-in cross-references, and practical design notes that are not found in a single place in the manufacturer datasheet, accelerating evaluation and procurement decisions for design engineers.

RFQ پەیوەندی
ADS7807PBG4 - 16-Bit 40kHz SAR ADC | Texas Instruments
ADS7807PBG4

ADS7807PBG4 - 16-Bit 40kHz SAR ADC | Texas Instruments

The Texas Instruments ADS7807PBG4 is a low-power, 16-bit, sampling CMOS analog-to-digital converter based on a successive-approximation-register (SAR) architecture, offering 40 kHz throughput in a 28-pin PDIP package. It operates from a single +5 V supply and dissipates only 35 mW typical, with a power-down mode consuming 50 µW for battery-friendly portable designs. Key specifications include ±1.5 LSB max INL, 16-bit no-missing-codes DNL, and 86 dB minimum SINAD with a 1 kHz input. A successive-approximation-register ADC is a type of data converter that performs a binary search through successive bit trials to resolve the input voltage in N clock cycles for N bits of resolution. SAR ADCs sit within the broader data-converter hierarchy of Nyquist-rate sampling ADCs, distinct from sigma-delta and pipeline architectures. They are prized for low latency, single-shot precision, and simplicity, making them the workhorse choice for industrial control loops, sensor digitisation, and instrumentation front ends. Key features of the ADS7807PBG4 include bipolar input ranges of ±5 V and 0 V to +4 V (plus 0 V to +5 V depending on configuration) without external signal conditioning, an integrated sample-and-hold amplifier, and flexible serial (SPI-compatible) or parallel data interface. The 25 µs maximum acquisition-and-conversion cycle keeps loop delays minimal, while external reference support lets designers trade noise, scale, and temperature drift against cost. The ADS7807PBG4 uses a charge-redistribution DAC array with a custom CMOS comparator and laser-trimmed resistors to achieve 16-bit linearity without missing codes across the full operating temperature range. Its input stage accepts single-ended bipolar signals through internal level-shifting, and the digital interface provides straight binary or two's-complement output coding for direct micro-controller or DSP hand-off. Typical applications include industrial process control, multi-channel data-acquisition systems, portable instrumentation, weigh scales, and battery-powered sensor digitisation. The low power dissipation makes it ideal for remote or handheld equipment. Designers should provide adequate input bandwidth, a low-impedance reference with a 10 µF bypass capacitor, and short analog-trace routing to preserve 86 dB SINAD. Do not exceed the absolute maximum ratings; for bipolar inputs add external clamping to keep transients within ±25 V. This page consolidates distributor pricing, drop-in alternatives, and design guidance that goes beyond the manufacturer datasheet to accelerate your evaluation and sourcing decisions.

RFQ پەیوەندی
ADS7807PG4 - 16-Bit 40kSPS Low-Power SAR ADC | Texas Instruments
ADS7807PG4

ADS7807PG4 - 16-Bit 40kSPS Low-Power SAR ADC | Texas Instruments

The Texas Instruments ADS7807PG4 is a low-power, 16-bit, sampling CMOS Analog-to-Digital Converter (ADC) housed in a 28-pin PDIP (through-hole) package. Built on a successive approximation register (SAR) architecture with a capacitive charge-redistribution DAC, the device integrates a sample-and-hold, internal clock, internal reference, and a configurable digital interface that supports both parallel and serial output modes. The converter operates from a single +5 V supply and accepts bipolar or unipolar input ranges of +/-10 V, +/-5 V, 0 V to 10 V, and 0 V to 4 V, making it a flexible front-end for industrial data-acquisition boards. A Successive Approximation Register (SAR) ADC is a type of data converter that resolves one bit per clock cycle by comparing the sampled input against a binary-weighted capacitor network driven by an internal reference. SAR ADCs sit between flash converters (very fast, low resolution) and sigma-delta ADCs (high resolution, slower) in the data-converter hierarchy, offering a balance of speed, accuracy, and deterministic latency that is well suited to multiplexed multi-channel measurement systems. Key specifications of the ADS7807PG4 include a maximum sampling rate of 40 kSPS, maximum acquisition-plus-conversion time of 25 us, +/-1.5 LSB maximum INL, 16-bit no-missing-codes DNL, and 86 dB minimum SINAD with a 1 kHz input. The part draws only 35 mW during conversion and falls to 50 uW in power-down mode, which makes it well matched to battery-instrumented or thermally-constrained designs. Operating temperature range is -40 C to +85 C (industrial grade). Architecture-wise, the ADS7807PG4 uses an inherent sample-and-hold front-end that allows the input stage to settle before conversion, removing the need for an external buffer in most applications. The internal 2.5 V reference is laser-trimmed and can be overdriven externally if system calibration is required. The output data bus can be configured for 8-bit or 16-bit parallel mode, plus a synchronous serial mode for low-pin-count designs. Typical applications include industrial process-control data-acquisition front ends, multi-channel instrumentation digitizers, weigh-scale and strain-gauge signal chains, panel meters, battery-powered portable test equipment, and medical instrumentation front ends. The wide +/-10 V true-bipolar input range removes external signal-conditioning in many PLC and SCADA designs. When designing with this part, place a 10 uF tantalum in parallel with a 0.1 uF ceramic bypass capacitor as close as possible to the +5 V supply pin, and ensure the analog input source impedance stays below the manufacturer's recommended maximum to keep INL within data-sheet limits. Use the BYTE and R/C pins to configure interface mode and initiate conversions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone, giving engineers a single reference for the ADS7807PG4.

RFQ پەیوەندی
ADS7807U - 16-Bit 40 kSPS Low-Power SAR ADC | Texas Instruments
ADS7807U

ADS7807U - 16-Bit 40 kSPS Low-Power SAR ADC | Texas Instruments

Texas Instruments ADS7807U is a 16-bit, 40 kSPS, single-input successive-approximation analog-to-digital converter in a 28-pin SOIC package. It operates from a single 4.75 V to 5.25 V supply, accepts bipolar ±10 V as well as unipolar 0 V to 5 V and 0 V to 4 V input ranges, and provides selectable internal or external reference operation. Maximum power dissipation is 35 mW, while power-down consumption is 50 µW. An ADC is a data-conversion semiconductor that converts a continuously varying analog voltage into a numeric code for measurement, control, or communication. The ADS7807 belongs to the sampling ADC hierarchy and uses the successive-approximation, or SAR, architecture. Unlike a pipeline or delta-sigma ADC, a SAR ADC successively resolves the input through a comparator and internal DAC, making this device suitable for compact, low-power instrumentation that needs precise conversion without a complex signal chain. The principal feature is 16-bit resolution with no missing codes, combined with differential nonlinearity specified as 16 bits and integral nonlinearity of ±1.5 LSB maximum. Signal-to-noise plus distortion is specified at a minimum of 86 dB for a 1 kHz input under the stated test conditions. Acquisition and conversion complete within 25 µs maximum, supporting the stated 40 kSPS conversion rate, while low-power operation limits dissipation to 35 mW maximum. The device supports both SPI-compatible serial output and a full parallel interface with byte select, giving designers flexibility in processor connectivity. A daisy-chain TAG function supports serial-interface arrangements, and an internal or external reference option permits the analog front end to use either the on-chip source or a higher-precision system reference. These features allow a single converter to serve serial microcontroller systems as well as parallel data-acquisition designs without changing the analog measurement function. Typical uses include industrial process monitoring, laboratory data acquisition, battery-powered measurement, factory automation, portable instrumentation, and control systems that require a compact 16-bit converter. In each case, the ADS7807U is placed between the measured sensor or conditioned analog signal and a digital controller, with the selected input range, reference, and serial or parallel interface matched to the system architecture. Designers should pay particular attention to source impedance, reference stability, input filtering, and grounding. Acquisition time must be sufficient for the input network to charge the internal sample-and-hold capacitor, and the analog return path should be kept short and quiet. Because the converter accepts both bipolar and unipolar ranges, the input-conditioning circuitry must not exceed the selected range or introduce nonlinear overdrive. This product page consolidates verified manufacturer and distributor specifications, pricing availability, family-level drop-in candidates, comparison parameters, and practical design guidance. It adds engineering-oriented context for engineers evaluating the ADS7807U while clearly separating verified values from information that still requires confirmation from an authoritative datasheet or distributor quote.

RFQ پەیوەندی
ADS7807UBE4 - 16-Bit 40kHz SAR ADC, 28-SOIC | Texas Instruments
ADS7807UBE4

ADS7807UBE4 - 16-Bit 40kHz SAR ADC, 28-SOIC | Texas Instruments

The Texas Instruments ADS7807UBE4 is a low-power, 16-bit, sampling CMOS analog-to-digital converter (ADC) based on a successive-approximation-register (SAR) architecture, housed in a 28-pin SOIC (DW) package with 0.295" (7.50 mm) body width. It supports input ranges of +/-10V, 0V to +5V, and 0V to +4V from a single +5V supply, integrating a sample-and-hold, clock, reference, and serial/parallel data interface on-chip. The -E4 suffix denotes the Tape and Reel packaging option within the wider ADS7807 family originally introduced by Burr-Brown (now part of Texas Instruments). What is a SAR ADC? A successive-approximation-register analog-to-digital converter is a precision converter type that uses a binary-search algorithm against an internal DAC to resolve an analog input one bit per conversion cycle. SAR ADCs sit in the precision data-converter hierarchy between delta-sigma converters (which trade speed for resolution) and flash converters (which trade resolution for speed), making the SAR topology the workhorse choice for 12-18 bit industrial, instrumentation, and data-acquisition applications where both resolution and deterministic latency matter. Key features include 35 mW maximum power dissipation, 50 uW power-down mode for battery-friendly duty-cycled operation, 25 us maximum acquisition-and-conversion time (yielding ~40 kSPS throughput), +/-1.5 LSB maximum INL, guaranteed 16-bit no-missing-codes DNL, and 86 dB minimum SINAD with a 1 kHz input. The pin-compatible 12-bit ADS7806 and the older pin-compatible 12-bit ADS7805 allow resolution migration on the same PCB layout. Internally, the ADS7807 uses a charge-redistribution capacitive DAC array for the SAR conversion, with the internal 2.5V reference driving the binary-weighted capacitor network. The converter offers both a serial (SPI/QSPI/MICROWIRE-compatible) interface and a parallel (8/16-bit) data bus, multiplexed on the same pins, enabling flexible MCU or DSP hook-up without external glue logic. A hardware BYS pin lets the user bypass the internal reference when system-level ratiometric accuracy is required. Typical applications include industrial process-control analog input modules, multi-channel data-acquisition (DAQ) boards, weigh-scale front ends, pen-trace digitizers, portable medical instrumentation, and precision sensor signal chains. The wide bipolar +/-10V input range also makes the part a strong fit for retrofit of legacy 12-bit +/10V systems that need higher resolution without changing the front-end scaling. When designing with the ADS7807UBE4, note that the part draws ~7 mA from +5V during conversion and drops to ~10 uA in power-down; therefore, the application logic should gate BUSY/R/C and shutdown for thermal and battery optimization. A 10 uF (minimum) tantalum plus 0.1 uF ceramic at +VANA and +VAND is recommended close to the pins to keep the reference regulator noise off the conversion floor. This page synthesizes distributor pricing, drop-in alternative analysis, and practical PCB/thermal notes that go well beyond what the manufacturer datasheet reproduces on its own.

RFQ پەیوەندی
ADS7808P 12-Bit 100 kHz Serial ADC | Texas Instruments
ADS7808P

ADS7808P 12-Bit 100 kHz Serial ADC | Texas Instruments

Texas Instruments ADS7808P is a 12-bit, 10 µs serial CMOS sampling analog-to-digital converter with a 100 kHz sampling rate, six specified input ranges including ±10 V and 0 V to 5 V, and a single +5 V supply. The device is packaged in a 20-pin plastic DIP (20-PDIP) package. Its 72 dB SINAD performance and ±1/2 LSB INL and DNL characteristics make it suitable for industrial instrumentation, data acquisition, process control, and precision signal-chain designs that require a compact, low-power serial ADC. An ADC, or analog-to-digital converter, is an integrated circuit that converts a continuously varying analog voltage into a digital code. The ADS7808P belongs to the SAR ADC family: a sample-and-hold circuit captures the input, and a capacitor-based successive-approximation register converts the captured voltage into a 12-bit result. This architecture combines deterministic conversion behavior with relatively low power consumption, making it useful when a system needs accurate measurements without a high-speed flash converter or complex external acquisition hardware. Key features include a 100 kHz maximum sampling rate, 72 dB SINAD with a 45 kHz input signal, six specified input ranges, and a serial output interface that can use either the internal clock or an external data clock. The converter also supports internal or external references. Its innovative single +5 V supply operation keeps system power requirements straightforward, while power dissipation remains below 100 mW according to the manufacturer datasheet. An output synchronization pulse helps interface the converter with standard digital signal processors. The serial interface reduces the number of signal lines required on a mixed-signal PCB, although the conversion timing and serial clock relationship must be handled correctly in firmware or external logic. The internal reference simplifies designs that do not need an externally trimmed or calibrated voltage source. The six input ranges support bipolar and unipolar measurement systems, allowing the same converter family to address sensor signals, industrial process voltages, and conditioned analog outputs. The 10 µs conversion time corresponds to the stated 100 kHz throughput capability when the interface permits continuous operation. Typical applications include multichannel industrial data acquisition, factory process monitoring, programmable logic controller analog input modules, laboratory measurement equipment, and embedded control systems. The ±10 V ranges are particularly useful for legacy industrial signals, while the 0 V to 5 V range suits sensors and low-voltage analog systems. The 12-bit resolution provides 4096 digital code levels across the selected input range and is appropriate for many control and monitoring tasks that require more precision than a coarse 8-bit converter but do not require a 16-bit part. A key design consideration is the analog input and reference network. Place the input filtering components close to the converter pins, use a low-noise reference arrangement, and keep digital clock and serial-data traces away from sensitive analog nodes. Check timing against the external data-clock option when communicating with a DSP, because synchronization behavior affects how each conversion is framed and sampled. This page combines the ADS7808P manufacturer specifications, pin and package guidance, application analysis, and drop-in-replacement criteria to support faster engineering review. Because exact replacement qualification depends on package, pinout, resolution, input range, timing, and supply requirements, any substitute should be checked against the manufacturer datasheet before production use.

RFQ پەیوەندی
ADS7808U - 12-Bit 100 kHz SAR ADC | Texas Instruments
ADS7808U

ADS7808U - 12-Bit 100 kHz SAR ADC | Texas Instruments

The Texas Instruments ADS7808U is a 12-bit, 10-µs serial CMOS-sampling analog-to-digital converter with a 100 kHz sampling rate, packaged in a 20-pin SOIC. It combines a capacitor-based SAR ADC, sample-and-hold circuit, reference, clock, and serial data interface in one device, delivering 72 dB SINAD with a 45 kHz input. Six specified input ranges and support for internal or external references allow the converter to accommodate different sensor and measurement signals. An ADC is an analog-to-digital converter, a mixed-signal semiconductor that converts a continuous voltage into a numeric code for measurement, control, or processing. The ADS7808 belongs to the SAR ADC hierarchy, where successive approximation compares the sampled input against a capacitor DAC. Compared with flash, pipelined, and sigma-delta converters, this architecture provides straightforward low-power conversion and a compact serial interface suitable for embedded acquisition systems. Key features include a maximum sampling rate of 100 kHz, 12-bit resolution, and linearity specified as ±1/2 LSB for INL and DNL. The converter operates from a single +5 V supply, uses a serial output, and accepts one analog input. Its maximum power dissipation is 100 mW. Pin compatibility with the 16-bit ADS7809 provides an upgrade path when greater resolution is needed without changing the package architecture. Internally, the ADS7808 uses state-of-the-art CMOS structures and supports conversion with its internal clock or synchronization to an external data clock. An output synchronization pulse simplifies interfacing with DSP-based systems. The internal reference can be used for standalone operation, while an external reference offers a route to improve stability or share precision reference circuitry across multiple channels. Typical applications include industrial process measurement, factory automation, DSP data acquisition, closed-loop control, and embedded instrumentation. The 100 kHz conversion rate and 12-bit code width are suitable for signals where rapid sampling and moderate resolution are required. The device is also appropriate for battery-powered or compact industrial systems because its stated maximum power dissipation is only 100 mW. When designing a circuit around the ADS7808U, verify the selected input range, reference configuration, logic levels, and digital interface timing against the manufacturer datasheet. Decoupling and analog signal-path layout are critical because the converter contains a sample-and-hold stage and may be sensitive to supply and reference noise. Confirm the complete conversion and data-read cycle before synchronizing it to a DSP. This page consolidates verified manufacturer and distributor information, package details, application guidance, and clearly qualified drop-in alternatives. It also highlights where direct cross-reference evidence is limited and where engineers must verify pin behavior, electrical limits, and availability before approving a replacement.

RFQ پەیوەندی
ADS7808UB/1K - 12-Bit 100kHz Serial SAR ADC | Texas Instruments
ADS7808UB/1K

ADS7808UB/1K - 12-Bit 100kHz Serial SAR ADC | Texas Instruments

The Texas Instruments ADS7808UB/1K is a 12-bit, 10 µs successive-approximation-register (SAR) analog-to-digital converter with a 100 kHz sampling rate, housed in a 20-pin SOIC (DW) package supplied on a 1,000-unit tape-and-reel carrier. The part integrates a precision sample-and-hold, internal reference, conversion clock, and a synchronous serial data interface, and is rated for an industrial –40 °C to +85 °C operating range on a +5 V single supply. An SAR ADC is a successive-approximation-register analog-to-digital converter: it compares the sampled input against a binary-weighted internal DAC bit-by-bit in N clock cycles (here N = 12), producing a deterministic, low-latency conversion ideal for multiplexed data-acquisition, motor control feedback loops, and DSP front-ends. Within the broader taxonomy, the ADS7808UB sits at: ADC -> data converter -> signal-chain IC -> semiconductor. The 72 dB SINAD and ±½ LSB INL/DNL specifications confirm true 12-bit performance with no missing codes. Key features include 100 kHz throughput, 72 dB SINAD at 45 kHz input, ±½ LSB integral and differential nonlinearity, six factory-trimmed input ranges (0–5 V, 0–10 V, ±5 V, ±10 V, etc.), serial data output that can be clocked from the internal oscillator or an external DSP clock, and a hardware SYNC pulse that simplifies frame alignment to standard serial ports. The reference is internal by default but may be overdriven externally for multi-channel ratio-metric systems. Typical applications include industrial process-control front-ends, multi-channel data-acquisition boards, DSP-based vibration and motor-control signal chains, portable instrumentation, and any pin-compatible upgrade path from the older ADS7808. When designing, note that the device is pin-compatible with the 16-bit ADS7809, providing an upgrade route without PCB rework, and that the internal reference settling time influences acquisition timing at higher throughput rates.

RFQ پەیوەندی
ADS7809PB - 16-Bit 100kHz Serial ADC | Texas Instruments
ADS7809PB

ADS7809PB - 16-Bit 100kHz Serial ADC | Texas Instruments

Texas Instruments ADS7809PB is a 16-bit, 100 kHz sampling, serial-output CMOS analog-to-digital converter housed in a 20-pin PDIP package. It provides ±2 LSB integral nonlinearity, 16-bit differential nonlinearity with no missing codes, 86 dB SINAD for a 20 kHz input, and six specified input ranges. The converter operates from a single +5 V supply and supports internal or external references. An ADC is a mixed-signal semiconductor that converts an analog voltage into a digital code for processing, measurement, control, or storage. The ADS7809 belongs to the sampling ADC hierarchy, specifically a successive-approximation-register converter with integrated sample-and-hold, clock, reference, and serial interface. These functions simplify instrumentation designs while preserving the throughput and resolution needed for precision control and measurement systems. Key features include a maximum sampling rate of 100 kHz, 16-bit resolution, and six selectable input ranges. According to the Texas Instruments product page and manufacturer datasheet, the converter achieves 86 dB SINAD with a 20 kHz input and is pin-compatible with the 12-bit ADS7808. A serial interface simplifies connection to processors, DSPs, and programmable logic without requiring a parallel data bus. Internally, the ADS7809 uses a capacitor-based successive-approximation architecture with an inherent sample-and-hold function, precision reference circuitry, an internal clock, and a serial output stage. The sampling process supports continuous conversion at up to 100 kHz, while the specified input architecture allows engineers to select ranges suited to bipolar or unipolar sensor signals. Maximum power dissipation is 100 mW under the stated operating conditions. Typical applications include industrial process monitoring, precision instrumentation, audio and communications signal measurement, industrial automation, and embedded sensor acquisition. The 100 kHz sampling rate is suitable for many industrial and control signals, while 16-bit resolution preserves low-level detail in measurements that do not require high-frequency waveform capture. When laying out the circuit, treat analog input, reference, and power-return connections as high-impedance paths even though the converter itself is digital. Keep input and reference traces short, provide the specified bypass capacitance near the supply pins, and route converter ground carefully with the analog signal source to minimize conversion error. This product page combines the ADS7809PB electrical characteristics, package details, sourcing information, comparison fields, and practical design guidance into a concise engineering reference. Use the manufacturer pin-description table and application circuit when finalizing PCB assignments, input conditioning, and decoupling.

RFQ پەیوەندی
ADS7809U - 16-Bit 100 kHz SAR ADC | Texas Instruments
ADS7809U

ADS7809U - 16-Bit 100 kHz SAR ADC | Texas Instruments

The Texas Instruments ADS7809U is a 16-bit, 100 kHz sampling successive-approximation register ADC with a 10 µs conversion time, six specified input ranges, and serial output in a 20-pin SOIC (DW) package. It operates from a single +5 V supply and can use either its internal clock or an external data clock. An SAR analog-to-digital converter is a sampling ADC that repeatedly estimates the input voltage through successive comparison steps. It belongs to the broader ADC category and provides a practical balance of resolution, conversion speed, power consumption, and circuit complexity. The ADS7809U combines a capacitor-based 16-bit SAR core, sample-and-hold circuitry, a reference, clocking, and a serial interface in one device. Key specifications include 16-bit resolution, a 100 kHz sampling rate, 86 dB SINAD with a 20 kHz input, and ±2 LSB integral nonlinearity. The converter also features 16-bit DNL with no missing codes, six specified input ranges, and single +5 V operation. These characteristics make it appropriate for precision industrial measurement, instrumentation, control, and signal-acquisition systems. The capacitor-based SAR architecture converts the sampled analog input through successive approximation. Data may be transferred through the serial interface using the internal oscillator or synchronized to an external data clock, giving the system designer flexibility in clocking and sampling control. The manufacturer data also identifies the ADS7809 as pin-compatible with the ADS7808, which can simplify comparison between related converter implementations. Typical uses include factory process monitoring, sensor-interface digitizers, laboratory measurement equipment, industrial control loops, and embedded data acquisition. The 86 dB SINAD figure is particularly relevant when the converted signal contains relatively little noise, while the 100 kHz sampling rate supports applications that require substantially more update speed than a slow-resolution integrating ADC. Designers should pay close attention to reference quality, source impedance, analog trace routing, decoupling, and digital-interface timing. The input network and reference must provide low enough noise and settling behavior to preserve the converter's specified accuracy, while the serial interface and clock source must meet the timing requirements described by Texas Instruments. This product data consolidates the verified manufacturer and distributor findings with explicit data gaps, practical engineering guidance, and same-footprint replacement analysis. It is intended to help engineers identify the correct ADC, validate board-level assumptions, and compare genuine 20-pin SOIC drop-in options without conflating merely similar devices with compatible replacements.

RFQ پەیوەندی
ADS7809UB - 16-Bit 10us SAR ADC | Texas Instruments
ADS7809UB

ADS7809UB - 16-Bit 10us SAR ADC | Texas Instruments

The Texas Instruments ADS7809UB is a 16-bit, 10 µs serial CMOS sampling analog-to-digital converter with one input, a successive-approximation register architecture, and a 20-pin SOIC package. It combines a sample-and-hold circuit, internal reference, clock, and serial data interface to provide complete single-channel data conversion in one device. An SAR ADC is a sampling analog-to-digital converter that compares the sampled input voltage with an internal DAC during a sequence of approximation steps. The ADS7809 uses this architecture to perform conversion in 10 µs. It can operate from its internal clock or synchronize conversion and data transfer to an external clock, allowing the converter to be coordinated with a digital system. The primary features of the ADS7809 include 16-bit resolution, one analog input channel, a 10 µs conversion time, and a serial CMOS interface. Its sampling architecture acquires the input during the sampling phase before performing successive-approximation conversion. The internal reference, clock, and interface reduce the number of external supporting functions required in a typical measurement circuit. Because the ADS7809 combines multiple converter functions in a single integrated circuit, it belongs to the broader ADC, data-converter IC, and signal-processing semiconductor hierarchy. The serial interface reduces the number of signal connections compared with a parallel converter, which can simplify PCB routing and integration with microcontrollers, DSPs, and embedded control systems. The architecture is particularly relevant when compactness, deterministic sampling, and serial data transfer are priorities. Typical uses include industrial process monitoring, sensor signal acquisition, laboratory instrumentation, communications equipment, and embedded data-acquisition systems. The one-input configuration makes it appropriate for measuring one analog quantity at a time, while the internal clock provides a straightforward operating mode for standalone or processor-controlled acquisition. Designers should follow the Texas Instruments ADS7809 datasheet for the complete pin description, recommended reference and bypass capacitors, acquisition timing, input-range configuration, and serial-interface sequencing. PCB signal-integrity practices are especially important when the source impedance is high or the ADC input is located far from the sensing element. This product page combines the exact ordering information and architecture description with practical design guidance, application analysis, package details, and honest drop-in replacement assessment. It is intended to help engineers identify whether the ADS7809UB matches their accuracy, conversion-speed, interface, and PCB-layout requirements before requesting a quote.

RFQ پەیوەندی
ADS7810U - 12-Bit 800 kHz SAR ADC | Texas Instruments
ADS7810U

ADS7810U - 12-Bit 800 kHz SAR ADC | Texas Instruments

Texas Instruments ADS7810U is a 12-bit successive-approximation-register analog-to-digital converter with a sampling rate of 800 kSPS, a 1.25 µs throughput time, and a single-ended analog input in a 28-pin SOIC package. It accepts a standard ±10 V input range and uses a parallel data interface with latches for transferring converted results. The converter also includes an internal reference, sample-and-hold circuit, and clock circuitry. An ADC is a data-conversion IC that transforms an analog voltage into a digital code for measurement, control, monitoring, or signal-processing systems. The ADS7810 belongs to the hierarchy of ADC, data-converter IC, signal-processing IC, and semiconductor. Its SAR architecture repeatedly compares the sampled input with an internal DAC, determining one output bit during each conversion step. This makes it appropriate for relatively high-speed industrial instrumentation where serial-interface overhead is undesirable. Key performance characteristics include 12-bit resolution, 800 kSPS sampling, ±3/4 LSB maximum integral nonlinearity, ±1 LSB maximum differential nonlinearity, and minimum SINAD of 69 dB with a 250 kHz input. The ±10 V input range supports direct acquisition of bipolar industrial signals. A 5 V digital supply supports compatibility with conventional parallel digital logic, while the analog supply operates from ±5 V according to the product description. The integrated sample-and-hold, reference, clock, and latched parallel outputs reduce the number of external support functions required. The 28-pin SOIC package is larger than modern fine-pitch packages but remains practical for through-hole assembly and moderate-density mixed-signal boards. Because the converter uses a parallel interface, its 12 output data lines require careful routing and adequate grounding to avoid logic coupling into the high-impedance analog input. Typical uses include industrial process monitoring, instrumentation, waveform capture, laboratory equipment, and embedded data-acquisition systems. Engineers should treat the analog input as a high-impedance node, provide adequate bypassing at the supply pins, and preserve the converter’s specified input-voltage limits. The ADC is not intended for signals outside its ±10 V range without suitable external attenuation or protection. A primary design consideration is signal conditioning. The source impedance, acquisition time, and input-network capacitance determine whether the sampled voltage can settle accurately within the converter’s acquisition interval. Short traces, guarding, clean references, and separated analog and digital return paths are especially important when converting small signals at high throughput. This page combines the manufacturer-linked datasheet information with a practical focus on acquisition timing, input conditioning, layout, and verified drop-in comparisons. It also distinguishes true same-package replacements from broader functional equivalents so engineers can assess PCB-reuse risk before selecting an alternative.

RFQ پەیوەندی
ADS7810U-1 - 12-Bit 800 kHz SAR ADC | Texas Instruments
ADS7810U-1

ADS7810U-1 - 12-Bit 800 kHz SAR ADC | Texas Instruments

Texas Instruments ADS7810U-1 is a 12-bit, single-channel successive-approximation register analog-to-digital converter with an 800 kS/s sampling rate, single-ended analog input, and a parallel data interface in a 28-pin SOIC package. The device operates from a 5 V digital supply and a ±5 V analog supply, making it suitable for bipolar analog measurement systems that require direct microprocessor interfacing. An analog-to-digital converter is an interface IC that converts a continuously varying analog voltage into a numerical representation for processing, measurement, or control. The ADS7810U-1 belongs to the SAR ADC hierarchy, where an internal sample-and-hold circuit and successive-approximation conversion process one analog sample at a time. This architecture is appropriate for industrial instrumentation, data acquisition, and embedded control systems where a parallel interface provides straightforward connection to digital processors. The principal specifications are 12-bit resolution, an 800 kS/s maximum sampling rate, one single-ended input, and a 28-pin SOIC package. The converter uses a 5 V digital supply and a ±5 V analog supply. Its specified operating temperature range is -40 °C to +70 °C. The parallel output supports direct access to conversion results without requiring a serial data link. Internally, the ADS7810 is described as a complete CMOS sampling converter containing a 12-bit capacitor-based SAR ADC, inherent sample-and-hold circuitry, a reference, a clock, and a microprocessor interface. The capacitor-based conversion core repeatedly resolves the input against internal charge redistribution. The parallel interface then presents the completed 12-bit result for acquisition by an external processor or latch. Typical applications include industrial process measurement, laboratory instrumentation, digital panel meters, closed-loop control, data-acquisition equipment, and embedded systems that sample bipolar analog signals. Its 800 kS/s conversion capability provides a practical balance between acquisition speed, interface simplicity, and analog measurement resolution. PCB design should preserve short, controlled analog-input traces and provide stable supply bypassing near the device. Because the converter uses parallel outputs, data-bus timing and output settling should be checked against the acquisition system’s clock requirements. The 28-pin SOIC footprint also requires enough spacing around the device for routing all address, control, data, analog, and supply connections. This page combines the core ADS7810U-1 specifications with application guidance, design notes, comparison data, and verified drop-in alternatives. It is intended to help engineers identify the correct ADC replacement while accounting for package compatibility, resolution, conversion rate, interface type, and supply requirements.

RFQ پەیوەندی
ADS7810U/1KG4 - 12-Bit 800kHz SAR ADC | Texas Instruments
ADS7810U/1KG4

ADS7810U/1KG4 - 12-Bit 800kHz SAR ADC | Texas Instruments

The Texas Instruments ADS7810U/1KG4 is a 12-bit, 800 kHz sampling successive approximation register (SAR) analog-to-digital converter with one single-ended input, internal sample-and-hold, internal reference, and a parallel data interface with output latches, housed in a 28-pin SOIC package. According to the manufacturer datasheet, it achieves a 1.25 us throughput time, 69 dB minimum SINAD with a 250 kHz input, +/-3/4 LSB maximum INL, and +/-1 LSB maximum DNL. The ADC accepts a standard +/-10 V input range and operates from analog supplies of +/-5 V plus a 5 V digital supply. An SAR ADC (Successive Approximation Register analog-to-digital converter) is a precision data-conversion architecture that uses a binary-search algorithm against an internal capacitive DAC to resolve an analog input one bit per clock cycle, producing deterministic latency and zero pipeline delay. In the broader data-converter hierarchy, SAR ADCs sit between flash converters (fastest, lowest resolution) and sigma-delta ADCs (slowest, highest resolution), and they are the dominant choice for 8- to 18-bit industrial, instrumentation, and process-control applications. Key features include an internal 2.5 V reference (with external-reference override option), a complete S/H, internal clock, self-bipolar input scaling that supports true +/-10 V swing, and a parallel data bus with read-only or write-then-read handshake modes. The 28-SOIC package provides robust mechanical handling for socketed designs and through-hole-style rework flows, while still being surface-mount-compatible for automated assembly. The ADS7810 architecture combines a charge-redistribution capacitive DAC with a low-noise comparator and on-chip clock generator, eliminating the need for an external sampling clock. The internal reference is trimmed for low drift, and the bipolar input network uses precision thin-film resistors for accurate gain, which is what enables the +/-10 V input range from a single-ended source on a +/-5 V analog supply. Typical applications include industrial process control, data acquisition systems, instrumentation, portable or bench-top test equipment, and optical or analytical front-ends where mid-resolution 12-bit conversion at sub-microsecond throughput is required. The wide +/-10 V input also makes it well suited to legacy 4-20 mA loop interfaces and motor-control position feedback. When designing with this ADC, pay close attention to the analog and digital supply decoupling network: at least 10 uF tantalum and 0.1 uF ceramic at each AVdd and DVdd pin, with the ground-return path kept separate to prevent digital switching noise from coupling into the SAR comparator. A small RC anti-alias filter (typically 100 ohm and 1 nF) at the input is recommended to limit wideband noise into the input network. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet. The /1KG4 suffix designates a 1,000-piece tape-and-reel packaging variant with green (Pb-free, RoHS-compliant) material set; the underlying die and electrical specifications are identical to the standard ADS7810U.

RFQ پەیوەندی
ADS7810UB - 12-Bit 800kHz SAR ADC ±10V | Texas Instruments
ADS7810UB

ADS7810UB - 12-Bit 800kHz SAR ADC ±10V | Texas Instruments

The Texas Instruments ADS7810UB is a 12-bit, 800 kHz sampling CMOS analog-to-digital converter (ADC) that delivers 1.25 µs throughput in a 28-pin SOIC (DW) package. It accepts a standard ±10 V input range, integrates a SAR architecture with inherent sample-and-hold (S/H), an internal reference, and a parallel microprocessor-compatible digital interface with output latches. According to the manufacturer datasheet, the device achieves 69 dB minimum SINAD at 250 kHz input, ±3/4 LSB maximum INL, and ±1 LSB maximum DNL at 12 bits. A successive-approximation register (SAR) ADC is a precision converter topology that resolves a single conversion in N clock cycles by switching a matched binary-weighted capacitor array against the input voltage. SAR ADCs sit at the bottom of the converter hierarchy: SAR ADC -> Nyquist-rate ADC -> data converter -> mixed-signal IC. They are favoured over delta-sigma or pipeline types when low-latency, single-shot acquisition with bipolar industrial input ranges is required. Key features include a complete single-chip solution (no external reference or S/H required), a wide ±10 V input range well suited to industrial transducer signal levels, low aperture uncertainty, and 8 + 4 parallel output bits that interface directly to standard microprocessors and DSPs. The internal reference is trimmed and the device draws low power, making it attractive for multi-channel multiplexed data-acquisition boards. Architecturally, the ADS7810UB uses a charge-redistribution capacitor DAC for SAR conversion, a buried-zener or bandgap-derived internal reference, and an onboard clock generator, eliminating most external components. Its parallel interface supports independent /RD and /CONVST control lines for synchronous sampling in multiple-ADC systems. Typical applications include industrial process-control front ends, factory-automation data-acquisition cards, medical instrumentation front ends, and the analog input stages of PLCs. The bipolar ±10 V range connects directly to many 4-20 mA loop receivers and transducer outputs after a single resistor scale. When designing with this part, ensure the analog ground and digital ground planes are joined at a single point near the converter and bypass supplies with a 10 µF tantalum in parallel with a 0.1 µF ceramic. Avoid routing digital switching edges near the analog inputs to preserve the 69 dB SINAD floor. This page synthesizes distributor pricing, drop-in alternatives in the same 28-SOIC footprint, and practical design notes not collected in any single manufacturer datasheet.

RFQ پەیوەندی
ADS7810UB/1K - 12-Bit 800kHz SAR ADC, ±10V Input | Texas Instruments
ADS7810UB/1K

ADS7810UB/1K - 12-Bit 800kHz SAR ADC, ±10V Input | Texas Instruments

The Texas Instruments ADS7810UB/1K is a 12-bit successive-approximation register (SAR) analog-to-digital converter with 800 kHz sampling throughput and a standard ±10 V input range, housed in a 28-pin SOIC package supplied on 1000-piece tape and reel. The integrated architecture includes a sample-and-hold amplifier, precision internal reference, and clock, so no external reference IC or high-frequency clock source is required to achieve full data-sheet performance. A SAR ADC is a converter that resolves the digital output one bit at a time by comparing the sampled-and-held analog input against a precision DAC driven by a successive-approximation register. SAR converters sit within the broader ADC taxonomy of successive-approximation ADC -> data converter -> mixed-signal IC -> semiconductor, and are valued for deterministic latency, low latency, and excellent DC accuracy versus pipeline or sigma-delta architectures that trade latency for higher speed or resolution. Key specifications include 1.25 µs typical throughput time, 69 dB minimum SINAD at 250 kHz input, ±0.75 LSB maximum integral nonlinearity (INL), ±1 LSB maximum differential nonlinearity (DNL), and a parallel data interface with read latches. The internal reference eliminates reference-bias resistor networks and simplifies board layout, while the bipolar ±10 V range allows direct connection to industrial transducer outputs and signal-conditioning stages. This part is built on a low-power CMOS process and supports a 2's-complement binary output format, simplifying software post-processing on microcontrollers or FPGAs that already expect signed data. The integrated design typically operates from a single +5 V supply, with logic-compatible parallel outputs that interface to 74HC or modern MCUs. Typical applications include industrial process control data acquisition, multi-channel multiplexed instrumentation systems, automated test equipment, and motor control feedback loops that demand deterministic conversion latency. Designers select the ADS7810UB/1K when the input swing is already at ±10 V and system noise bandwidth is well below Nyquist. When designing with this ADC, allocate adequate settling time on the input amplifier and ensure the reference decoupling follows the datasheet recommended capacitor network. The parallel interface simplifies layout but consumes more board traces than an SPI-based ADC, so plan FPGA/MCU pin allocation early. This page synthesizes distributor pricing, drop-in alternative listings, and PCB design notes not found in the manufacturer datasheet alone, providing an at-a-glance comparison view for engineers selecting a 12-bit, 800 kHz SAR ADC for industrial acquisition.

RFQ پەیوەندی
ADS7811U - 16-Bit 250 kSPS SAR ADC | Texas Instruments
ADS7811U

ADS7811U - 16-Bit 250 kSPS SAR ADC | Texas Instruments

The Texas Instruments ADS7811U is a 16-bit, 250 kSPS, single-channel successive-approximation analog-to-digital converter with a single-ended input, housed in a 28-pin SOIC package. It combines a capacitor-based SAR converter, an inherent sample-and-hold circuit, a precision internal reference, and an internal clock in one analog signal-conditioning device. The ADS7811U is intended for industrial instrumentation, process control, data acquisition, sensor measurement, and embedded systems that require accurate conversion of a single bipolar or unipolar analog signal. An ADC converts a continuously varying analog voltage into a numeric code for processing, measurement, or control. The ADS7811 uses a successive-approximation architecture, where an internal capacitor array and successive bit trials produce one conversion result after each sample. The 16-bit resolution provides 65,536 possible codes, while the 250 kSPS throughput rate supports signal monitoring and control loops. Its single-ended input simplifies connection to sensors and signal-conditioning circuits compared with a differential-input converter. The principal device characteristics are 16-bit resolution, a 250 kSPS conversion rate, one single-ended analog input, and the 28-pin SOIC package. According to the manufacturer product page and datasheet, the design is intended to provide excellent AC performance and a spurious-free dynamic range exceeding typical expectations for a 100 kHz full-scale sine-wave input. The internal reference and clock reduce external component count and help simplify system design, while the wide operating and temperature options support industrial equipment. Typical deployments include industrial process-control loops, factory automation, environmental monitoring, portable instrumentation, and embedded data loggers. In each case, the converter sits between an analog sensor or signal-conditioning network and a digital controller or communications interface. The ADS7811U is appropriate when a compact, single-channel, moderate-speed SAR ADC is preferable to a higher-speed, higher-channel-count converter. For layout, place input, reference, and decoupling capacitors close to their associated pins and route analog and digital return currents carefully. The analog input must remain within the device’s specified input range, and the system should account for acquisition time, settling behavior, and the relationship between input impedance and sampling dynamics. Review the manufacturer datasheet pin description table and the recommended application circuit before finalizing PCB connections. This product page combines the manufacturer specifications, package information, practical application guidance, and drop-in comparison context to support faster engineering selection and sourcing.

RFQ پەیوەندی
ADS7811U/1K - 16-Bit 250kSPS SAR ADC, 28-SOIC | Texas Instruments
ADS7811U/1K

ADS7811U/1K - 16-Bit 250kSPS SAR ADC, 28-SOIC | Texas Instruments

The Texas Instruments ADS7811U/1K is a 16-bit, 250-kSPS successive-approximation register (SAR) analog-to-digital converter with a single-ended input, supplied on a 28-pin SOIC (DW) tape-and-reel carrier. The device integrates a 4 µs conversion engine, internal clock, and a parallel output interface, drawing from a single +5 V analog supply. The /1K suffix designates the 1,000-piece tape-and-reel packaging variant. An SAR ADC is a class of analog-to-digital converter that uses a binary search algorithm, implemented by a successive-approximation register, to digitize each analog sample in a fixed number of clock cycles. The architecture is valued for its deterministic latency, low power consumption, and excellent DC accuracy, which together make SAR converters the standard choice for multiplexed data-acquisition systems, industrial control loops, and instrumentation front ends. As a member of the wider data-converter hierarchy, the ADS7811 sits between sigma-delta (which trades speed for higher resolution) and flash/pipeline ADCs (which trade resolution for multi-MSPS speeds). Key specifications include 16-bit no-missing-codes performance, ±1 LSB INL typical, 0.0092 % linearity error, and 4 µs typical conversion time. The device operates from a single +5 V supply and accepts unipolar 0–VREF or ±10 V true-bipolar analog inputs through its configurable input front end. The 28-SOIC footprint keeps the part compatible with hand-reworkable through-hole-adjacent designs and is identical to that of the ADS7807U, ADS8505, and ADS7805U family, enabling multi-generation PCB reuse. Typical applications include industrial process control, multi-channel data-acquisition boards, digital oscilloscope front ends, weigh scales, and precision instrumentation. The combination of 250 kSPS throughput and 16-bit accuracy suits mid-bandwidth transducer digitization where a multiplexer precedes the converter. The internal 2.5 V reference can be overdriven by an external system reference when ratio-metric or ratiometric measurements are required. A primary design consideration is input-signal conditioning: a low-impedance driver amplifier must settle within the 4 µs acquisition window to avoid conversion errors. For multi-channel systems, ensure the front-end multiplexer switches settle before the CONVST pulse. The 28-SOIC thermal pad (if present on the package variant) should be soldered to a copper pour to minimize ground-bounce and keep the digital outputs within noise margins. This page synthesizes verified distributor pricing, drop-in alternatives drawn from the same 28-SOIC SAR ADC family, and practical design notes that go beyond what is found in the manufacturer datasheet alone. Pin-compatible variants from Texas Instruments and qualified second-source suppliers are tabulated side-by-side so engineers can quickly evaluate substitutes without leaving the page.

RFQ پەیوەندی
ADS7811U/1KG4 - 16-Bit 250kHz SAR ADC, 28-SOIC | TI
ADS7811U/1KG4

ADS7811U/1KG4 - 16-Bit 250kHz SAR ADC, 28-SOIC | TI

The Texas Instruments ADS7811U/1KG4 is a 16-bit, 250-kSPS successive-approximation register (SAR) analog-to-digital converter with a single-ended analog input channel, offered in a 28-pin SOIC (DW) package and supplied on a 1,000-piece tape-and-reel reel. The ADS7811U/1KG4 integrates a 16-bit capacitor-based SAR ADC with an inherent track-and-hold front end, an internal precision reference, and an internal conversion clock, eliminating the need for external reference components and simplifying PCB design. According to TI's ADS7811 product page, the converter achieves >100 dB SFDR with a 100 kHz full-scale sine input while operating from ±5 V analog and 5 V digital supplies. A SAR ADC is a type of analog-to-digital converter that uses a binary-search successive-approximation algorithm to digitize an input signal one code at a time per clock cycle. SAR ADCs sit in the data-converter hierarchy between flash converters (which are fastest but lowest resolution) and delta-sigma converters (which offer the highest resolution at lower bandwidth). The SAR architecture is favored for 12- to 18-bit, 100-kSPS-to-1-MSPS multi-channel data-acquisition systems where low latency, deterministic throughput, and excellent AC linearity are required. Key features of the ADS7811U/1KG4 include 250 kHz throughput, integral nonlinearity typically 0.0092%, ±10 V (or 0 to 4 V) true bipolar input ranges, a serial data interface, and an operating temperature range of -25 °C to +85 °C. The internal 2.5 V reference is trimmed for low drift, and a REF_OUT pin supplies external circuitry. The 28-pin SOIC footprint occupies a modest board area suited to industrial data-acquisition boards, instrumentation front-ends, and DSP-ready signal chains. Typical applications include industrial process-control analog input modules, multi-channel data-acquisition systems, digital signal processing front-ends, test and measurement equipment, and medical instrumentation signal chains where 16-bit resolution at moderate sample rates is required. The wide bipolar input range supports direct connection to ±10 V transducer outputs without external signal conditioning. When designing with this device, ensure the analog and digital supplies are decoupled with 10 µF tantalum and 0.1 µF ceramic capacitors placed as close as possible to the supply pins. Maintain a clean analog ground plane separate from the digital ground, joining them only at the AGND-to-DGND pin. The conversion clock, serial data, and CS signals should be routed away from the analog input traces to avoid digital noise coupling into the conversion result. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes that go beyond the manufacturer datasheet.

RFQ پەیوەندی
ADS7812P - 12-Bit, 40 kS/s Low-Power SAR ADC | Texas Instruments
ADS7812P

ADS7812P - 12-Bit, 40 kS/s Low-Power SAR ADC | Texas Instruments

The Texas Instruments ADS7812P is a low-power, 12-bit successive-approximation-register analog-to-digital converter with a conversion rate of 40 kS/s, a 20 us maximum conversion time, and a 16-pin plastic DIP package. It operates from a single 4.75 V to 5.25 V supply and includes a sample-and-hold circuit, clock, reference, and serial data interface. The converter supports single-ended input, up to three analog inputs, and selectable bipolar or unipolar input polarity. An ADC is a semiconductor that converts an analog voltage into a digital number for processing, storage, or transmission. The ADS7812P belongs to the successive-approximation-register ADC family, a low-power architecture that compares the sampled input against a capacitor-based internal DAC during successive conversion steps. Its 12-bit resolution provides 4,096 digital codes, making it suitable for data acquisition, industrial control, test equipment, and digital signal processing systems. Key characteristics include ±0.5 LSB maximum integral and differential nonlinearity, 74 dB signal-to-noise ratio, 98 dB spurious-free dynamic range, and at least 72 dB SINAD. The converter can use its internal reference or an external reference, while the power-down mode limits consumption to 50 uW. These characteristics support accurate measurements in systems that do not require the throughput of a high-speed flash converter. The serial interface reduces the number of PCB traces required to connect the converter to a microcontroller, digital signal processor, or programmable logic controller. The ADS7812 family is also pin-compatible with the 16-bit ADS7813, allowing engineers to evaluate resolution changes on a common PCB footprint. Multiple input ranges and selectable polarity broaden its usefulness in sensor, process-control, and instrumentation systems. Typical applications include industrial process monitoring, laboratory data acquisition, digital signal processing, embedded instrumentation, and factory test equipment. Its low-power operation is especially useful where the converter must operate continuously from a single 5 V supply without the power and EMI characteristics of a high-speed switching converter. The primary design consideration is analog signal conditioning. The input source must remain within the selected input range, the reference must be stable, and the serial clock and digital interface must be arranged to satisfy the converter timing requirements. A common mistake is to choose a wide input range for convenience and lose useful code resolution; selecting the narrowest range that safely covers the signal improves effective measurement precision. This product page consolidates the manufacturer specifications, package information, application guidance, and verified replacement candidates into an engineering-oriented reference. It also distinguishes exact drop-in compatibility from changes in resolution or ordering code, helping designers decide whether a substitution can preserve the existing PCB and signal chain.

RFQ پەیوەندی