Amplifier ICs
بەرهەمەکان (3,200+)
OPA810IDCKR - 140MHz RRIO FET-Input Op Amp | TI SC70-5
The Texas Instruments OPA810IDCKR is a single-channel, FET-input, voltage-feedback operational amplifier with rail-to-rail input and output (RRIO) capability, supplied in a 5-pin SC-70 (DCK) package. It provides a small-signal unity-gain bandwidth of 140 MHz, a low quiescent current of 3.7 mA per channel, and a wide supply range that supports ±27 V (or 0 V to 27 V single-supply) operation. According to the TI datasheet, the OPA810 is fabricated on Texas Instruments' proprietary high-speed SiGe BiCMOS process, achieving significant performance improvements versus comparable FET-input amplifiers at similar quiescent current levels. An operational amplifier (op amp) is an analog active device that amplifies the difference between two input voltages and drives a single-ended output. FET-input op amps use junction field-effect transistors at the input stage, producing input bias currents in the picoampere (pA) range - orders of magnitude lower than bipolar-input alternatives. The OPA810 belongs to the high-speed, low-noise, low-bias-current sub-category of FET-input amplifiers, positioned between TI's general-purpose CMOS-input op amps and its ultra-precision zero-drift families. Key features include a 140 MHz unity-gain bandwidth, 80 V/µs slew rate, FET-input bias current typically in the pA range, rail-to-rail input and output swing, low input offset voltage, low THD+N at audio frequencies, and integrated shutdown logic on dual-channel variants. The SC-70-5 package occupies roughly 2.1 mm × 2.1 mm of PCB area and supports -40 °C to +125 °C extended industrial temperature operation. The device is unity-gain stable and supports capacitive loads up to several nanofarads without external compensation. Architecturally, the OPA810 uses SiGe BiCMOS fabrication, allowing high-speed NPN transistors in the signal path alongside CMOS biasing and shutdown logic. This achieves the noise and bandwidth of more expensive bipolar parts while preserving the high input impedance and ultra-low bias current of FET input stages. The RRIO topology maximizes dynamic range on low-voltage supplies, while dual-channel variants integrate a logic-level shutdown pin. Typical applications include high-impedance analog sensor front-ends (pH electrodes, photodiodes, piezoelectric transducers), test and measurement front-ends, ADC and DAC input/output buffers, motor and solenoid drive stages, photomultiplier amplifier chains, audio line drivers and headphone buffers, and high-side/low-side current-sense amplifiers. The wide supply range also makes it useful in 24 V industrial signal chains. When designing with the OPA810IDCKR, observe standard SOT-23-class PCB layout - bypass capacitors within 1 mm of the supply pins, a ground plane underneath the part, and minimal input trace lengths. Maintain feedback resistors below approximately 10 kΩ to preserve phase margin with the capacitive input of downstream ADCs. This page synthesizes distributor pricing, drop-in alternatives, and PCB-level design guidance not found in the raw manufacturer datasheet, optimized for engineers sourcing the OPA810IDCKR for production-grade analog front-end designs.
OPA820ID - Low-Noise Unity-Stable Op Amp | Texas Instruments
Texas Instruments OPA820ID is a unity-gain-stable, low-noise, voltage-feedback operational amplifier packaged in an 8-pin SOIC. It is intended for precision analog signal chains requiring low input noise, high output current capability, and a supply current of 5.6 mA. The device contains one amplifier circuit and supports closed-loop operation at unity gain. An operational amplifier is a voltage-gain element that uses differential feedback to amplify the voltage difference between its inverting and non-inverting inputs. The OPA820 belongs to the voltage-feedback operational amplifier family, where feedback sets the closed-loop gain. Voltage-feedback amplifiers are commonly used in sensor conditioning, test equipment, communications, imaging, and precision measurement because they provide predictable bandwidth behavior and straightforward external compensation. The OPA820's defining characteristics include its low-noise design, unity-gain stability, voltage-feedback topology, single-amplifier configuration, and low 5.6 mA supply current. Unity-gain stability allows the amplifier to operate as a buffer without requiring an added compensation network. This simplifies low-level signal paths where source impedance can make the amplifier input noise, bias current, and offset-voltage behavior important. OPA820ID is packaged in the standard 8-pin SOIC surface-mount format. Its compact outline supports conventional PCB assembly while exposing separate supply, input, and output connections. When evaluating a complete amplifier design, consult the manufacturer datasheet for gain-bandwidth product, slew rate, input-noise density, input offset voltage, input bias current, output-current capability, common-mode range, and supply-voltage limits. Typical uses include low-level sensor amplification, photodiode signal chains, high-speed instrumentation, communications interfaces, active filtering, and precision measurement equipment. In these applications, low input noise helps preserve weak signals, while the voltage-feedback architecture supports controlled gain and bandwidth. The unity-gain-stable configuration is particularly useful in buffers and follower stages placed close to sensitive sources. For reliable performance, place the amplifier close to the signal source, keep feedback traces short, and use decoupling capacitors according to the manufacturer datasheet. Check output swing, slew-rate limits, and load capability before driving downstream circuitry. Stable operation also depends on maintaining the specified supply voltage and avoiding excessive capacitive loading at the output. This page combines manufacturer-device identification, verified distributor listings, application guidance, pin and package information, and engineering design notes to support component selection and PCB implementation. The OPA820ID datasheet is the controlling technical reference for electrical limits, test conditions, typical performance curves, package dimensions, and recommended application circuits.
OPA827 - Low-Noise JFET Op Amp | Texas Instruments
The OPA827 is a low-noise, high-precision, JFET-input operational amplifier from Texas Instruments. It combines outstanding DC precision with excellent AC performance, featuring a maximum input offset voltage of 150 µV, a typical drift of 0.5 µV/°C, a typical input bias current of 3 pA, and very low 0.1-Hz to 10-Hz noise of 250 nVPP. The device is unity-gain stable and operates from a single or dual supply, with a wide supply range of ±4 V to ±18 V (or 8 V to 36 V single supply). It is available in 8-pin SOIC and 8-pin VSSOP packages, specified for operation from -40°C to +125°C. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, used in signal conditioning, filtering, and instrumentation. The OPA827 belongs to the JFET-input op amp family, which offers very high input impedance and low input bias current, making it ideal for interfacing with high-impedance sources such as sensors and photodiodes. Within the hierarchy of analog ICs, it is a precision amplifier, a subset of linear amplifiers, and part of the broader signal chain IC category. Key features of the OPA827 include its low offset voltage (150 µV max), low drift (0.5 µV/°C typ), low bias current (3 pA typ), and low noise (4 nV/√Hz at 10 kHz, 250 nVPP 0.1-10 Hz). It also offers a high open-loop gain of 120 dB, a gain bandwidth product of 22 MHz, and a slew rate of 28 V/µs. The device is fully specified over the extended temperature range and is RoHS compliant. Technically, the OPA827 uses a JFET input stage to achieve its low bias current and high input impedance, while a precision bipolar output stage provides low output impedance and high drive capability. The amplifier is internally compensated for unity-gain stability, simplifying design. Its low distortion and high linearity make it suitable for high-performance audio and precision instrumentation. Typical applications include high-end audio preamplifiers and DAC output buffers, precision data acquisition systems, active filters, and sensor signal conditioning. The low noise and low bias current are particularly beneficial in photodiode amplifiers and medical instrumentation. When designing with the OPA827, ensure proper decoupling of the power supply pins with 0.1 µF ceramic capacitors placed close to the device, as recommended in the datasheet. Also, consider the input common-mode range and output swing limitations for your specific supply voltages.
OPA828 - 45MHz 36V JFET Op Amp, 4nV Noise | TI
The Texas Instruments OPA828 is a high-speed JFET-input operational amplifier delivering 45 MHz gain bandwidth product, 150 V/us slew rate, and 36 V operation with rail-to-rail output (RRO) in SOIC-8 and HVSSOP-8 (DGN) packages. It is the next-generation successor to the industry-standard OPA627 and OPA827, combining high speed with high DC precision. A JFET-input operational amplifier is a linear amplifier IC whose input stage uses junction field-effect transistors, giving it extremely low input bias current (picoampere level) while preserving the voltage-noise performance of a bipolar front end. Within the power management and signal-chain hierarchy, op amps form the core of analog signal conditioning between sensors and data converters. Key features include 4 nV/Hz input voltage noise density at 1 kHz, only 60 nVRMS of noise from 0.1 Hz to 10 Hz, 50 uV input offset voltage, and 0.45 uV/C offset drift. JFET inputs draw just 1 pA typical bias current, and MUX-friendly inputs simplify multiplexed signal chains. The wide supply range of +/-4 V and above supports 36 V single-supply operation. Architecturally, the OPA828 pairs a precision JFET input stage with a rail-to-rail output stage, enabling maximum output swing into ADCs and loads on low supply rails. Compared with the OPA627, TI documents wider bandwidth, higher slew rate, and rail-to-rail output as the key upgrade paths (per the TI comparison tool). Typical applications include photodiode transimpedance amplifiers, precision ADC driver front ends, high-fidelity audio stages, and test-and-measurement signal conditioning where low bias current, low noise, and high speed must coexist. Design consideration: ensure headroom for the JFET common-mode input range, and decouple supply pins with 0.1 uF ceramics placed within 2 mm; for TIA use, compensate feedback capacitance against input capacitance to preserve phase margin.
OPA828ID - 45MHz JFET Op Amp, 4nV/√Hz | TI | Precision Amplifier (Tape & Reel)
The Texas Instruments OPA828ID is a high-speed, JFET-input operational amplifier delivering 45 MHz gain bandwidth, 150 V/us slew rate, and 4 nV/√Hz voltage noise in an 8-pin SOIC package. It operates over a wide supply range of ±4 V to ±18 V (36 V total) with rail-to-rail output (RRO), positioning it as the next-generation successor to the legendary OPA627 and OPA827 op amps. A JFET-input operational amplifier is a type of precision amplifier whose input stage uses junction field-effect transistors, providing extremely low input bias current (picoampere range) and high input impedance. Within the signal-chain hierarchy, op amps sit between sensors and data converters, serving as the general-purpose analog building block for amplification, filtering, buffering, and transimpedance conversion. Key features include 50 uV input offset voltage, 0.45 uV/C offset drift, 1 pA typical input bias current, and only 60 nVRMS of noise from 0.1 Hz to 10 Hz. These DC precision specifications make the OPA828 suitable for applications where both speed and accuracy are demanded simultaneously - a rare combination. MUX-friendly inputs allow multiplexed signal chains without settling artifacts or charge-injection damage. Architecturally, the OPA828 pairs a JFET input stage with a rail-to-rail output stage, combining classic precision topology with modern output swing. The RRO output maximizes dynamic range in low-voltage systems while the 36 V supply rating supports traditional ±15 V industrial analog rails without redesign. Typical applications include photodiode transimpedance amplifiers (TIA), high-fidelity audio front ends, precision ADC and DAC buffer stages, and active filters in test and measurement instrumentation. The wide 36 V supply range is particularly valuable for industrial designs retaining legacy ±15 V rails. For design, ensure supply decoupling with 0.1 uF ceramic capacitors placed within 3 mm of each supply pin. When replacing an OPA627, verify compensation and bias-current paths, as community feedback shows some legacy TIA circuits require adjustment despite pin compatibility. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
OPA828IDR - 45MHz JFET Op Amp, 4nV/√Hz | TI | Precision Amplifier
The Texas Instruments OPA828IDR is a high-speed, JFET-input operational amplifier delivering 45 MHz gain bandwidth, 150 V/us slew rate, and 4 nV/√Hz voltage noise in an 8-pin SOIC package. It operates over a wide supply range of ±4 V to ±18 V (36 V total) with rail-to-rail output (RRO), positioning it as the next-generation successor to the legendary OPA627 and OPA827 op amps. A JFET-input operational amplifier is a type of precision amplifier whose input stage uses junction field-effect transistors, providing extremely low input bias current (picoampere range) and high input impedance. Within the signal-chain hierarchy, op amps sit between sensors and data converters, serving as the general-purpose analog building block for amplification, filtering, buffering, and transimpedance conversion. Key features include 50 uV input offset voltage, 0.45 uV/C offset drift, 1 pA typical input bias current, and only 60 nVRMS of noise from 0.1 Hz to 10 Hz. These DC precision specifications make the OPA828 suitable for applications where both speed and accuracy are demanded simultaneously - a rare combination. MUX-friendly inputs allow multiplexed signal chains without settling artifacts or charge-injection damage. Architecturally, the OPA828 pairs a JFET input stage with a rail-to-rail output stage, combining classic precision topology with modern output swing. The RRO output maximizes dynamic range in low-voltage systems while the 36 V supply rating supports traditional ±15 V industrial analog rails without redesign. Typical applications include photodiode transimpedance amplifiers (TIA), high-fidelity audio front ends, precision ADC and DAC buffer stages, and active filters in test and measurement instrumentation. The wide 36 V supply range is particularly valuable for industrial designs retaining legacy ±15 V rails. For design, ensure supply decoupling with 0.1 uF ceramic capacitors placed within 3 mm of each supply pin. When replacing an OPA627, verify compensation and bias-current paths, as community feedback shows some legacy TIA circuits require adjustment despite pin compatibility. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
OPA830ID - 110MHz Wideband Op Amp | Texas Instruments
Texas Instruments OPA830ID is a low-power, single-supply, wideband, voltage-feedback operational amplifier with a 110 MHz gain-bandwidth product, packaged in an 8-pin SOIC. It operates from a single 3 V or 5 V supply and also supports ±5 V or +10 V supplies. Its input range extends below the negative supply and to within 1.7 V of the positive supply, while the output can swing to within 25 mV of either supply. A wideband operational amplifier is a voltage-feedback amplifier designed for signal amplification over a broad frequency range. The OPA830 belongs to the amplifier IC hierarchy, where its 110 MHz gain-bandwidth product and approximately 9.2 nV/√Hz input voltage noise support high-speed, low-noise signal conditioning. This makes the device relevant to data acquisition, communications, instrumentation, and precision analog systems where bandwidth and signal fidelity must coexist with low power consumption. Key features include a 110 MHz gain-bandwidth product, a 9.2 nV/√Hz input voltage-noise density, and an input common-mode range that extends below the negative supply. The amplifier can operate from 3 V, 5 V, ±5 V, or +10 V, reducing the number of required supply arrangements. Its complementary common-emitter output stage produces an output swing to within 25 mV of the supply rails, providing useful output range for low-voltage signal chains. OPA830ID is a single-amplifier device intended primarily for fixed-gain line-driver applications. Texas Instruments also identifies OPA832 as an option for fixed-gain line-driver designs when its particular gain and performance characteristics are better suited to the system. The OPA830's voltage-feedback architecture makes feedback-network selection and stability assessment important when setting closed-loop gain. Typical uses include low-power signal buffering, communications-interface signal conditioning, precision measurement front ends, and mixed-signal subsystem interfacing. The 110 MHz bandwidth can preserve higher-frequency content in video, data-conversion, and control paths, while the low-noise specification supports high-dynamic-range analog stages. The 8-pin SOIC format also supports conventional surface-mount assembly and hand-soldering workflows. When designing around the OPA830ID, preserve the usable input and output ranges by checking signal swing against the actual supply voltage and load. Decoupling capacitors should be placed close to the supply pins, and feedback traces should remain short to minimize parasitic effects. Stability, gain-bandwidth trade-offs, and permissible output loading should be evaluated using the manufacturer datasheet rather than inferred from the nominal 110 MHz figure. This page combines the exact orderable MPN, manufacturer documentation, package information, sourcing details, application guidance, and an engineering comparison for engineers evaluating the OPA830ID for low-power wideband amplification.
OPA842ID - 400 MHz Low-Distortion Op Amp | Texas Instruments
Texas Instruments OPA842ID is a wideband, low-distortion, unity-gain-stable voltage-feedback operational amplifier with a 400 MHz gain-bandwidth product, 400 V/us slew rate, and single-amplifier configuration in an 8-pin SOIC package. It operates from ±5 V to ±6 V and is specified for -40 °C to +85 °C ambient temperature operation. An operational amplifier is a high-gain differential amplifier used to amplify small input signals while imposing minimal distortion or unwanted noise. The OPA842 belongs to the voltage-feedback amplifier family within the broader operational-amplifier and signal-conditioning semiconductor hierarchy. Its unity-gain stability permits operation as a low-noise gain stage without requiring external compensation for a unity-gain configuration. The device uses a voltage-feedback architecture with two internal gain stages. According to the Texas Instruments OPA842 product information, this design provides a combination of high speed and dynamic range while maintaining low harmonic distortion across a wide frequency range. The 400 MHz gain-bandwidth product supports high-bandwidth signal processing, while the 400 V/us slew rate allows the amplifier to reproduce large-amplitude, rapidly changing signals with limited slew distortion. OPA842ID is suitable for test and measurement, communications, video, imaging, and general-purpose analog signal-chain applications. It can serve as a low-gain buffer, a wideband voltage amplifier, a driver for downstream circuitry, or an active element in analog filtering and feedback networks. Unity-gain stability is especially useful when the required closed-loop gain is close to 1. The principal design tradeoff is operating speed versus power dissipation and system noise. High-speed feedback loops require short, well-controlled PCB traces, stable power-supply bypassing, and careful termination of unused inputs. Follow the pin-description and typical-application tables in the manufacturer datasheet when assigning input bias, supply connections, output loads, and compensation values. This product page consolidates the verified device identity, package and operating details, application guidance, comparison parameters, and design considerations needed to evaluate OPA842ID before schematic capture or prototype assembly.
OPA843ID - 800 MHz Wideband Operational Amplifier | Texas Instruments
The Texas Instruments OPA843ID is a single-circuit, wideband, low-distortion, medium-gain voltage-feedback operational amplifier with an 800 MHz gain-bandwidth product, 1000 V/us slew rate, and operation from a 10 V to 12 V supply in an 8-pin SOIC package. Designed for high-speed signal chains, it combines broad bandwidth with low distortion and is suitable for communications, test-and-measurement, video, and data-acquisition systems. A voltage-feedback operational amplifier is a feedback-controlled amplifier that uses the error at its inverting input to correct the output. The OPA843 belongs to the broader operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, comparators, and other analog signal-conditioning ICs. Its medium closed-loop gain range and wide operating bandwidth make it particularly useful when a design needs accurate high-frequency amplification rather than only low-frequency precision. The primary performance characteristics include an 800 MHz gain-bandwidth product and a 1000 V/us slew rate. These figures allow the amplifier to preserve large-amplitude signals encountered in instrumentation and RF-adjacent signal chains. The device operates from 10 V to 12 V, giving designers sufficient headroom for wide-swing output stages while supporting a dual-supply implementation centered at zero volts. The specified operating-temperature range extends from -40 °C to +85 °C for industrial-temperature applications. OPA843ID is configured as a voltage-feedback amplifier rather than a current-feedback amplifier. This topology supports conventional resistive feedback networks and is familiar to engineers designing gain blocks, active filters, impedance drivers, and signal conditioners. Because the package is an 8-pin SOIC, PCB footprint reuse is straightforward when a new amplifier has the same supply arrangement, pin functions, and feedback topology. Pin assignments and support-network details should nevertheless be checked against the manufacturer datasheet before production release. Typical applications include broadband instrumentation, communications receivers, analog-to-digital converter input interfaces, active filters, pulse-shape circuits, and test equipment. In these applications, the 800 MHz bandwidth handles fast transitions while the 1000 V/us slew rate limits slew-related distortion. When driving cables, analog-to-digital converters, or other finite-impedance loads, the output-current capability and output-voltage swing should be checked against the actual load and supply conditions. The main design trade-off is supply and output-stage headroom. A 10 V to 12 V supply supports high output swing, but it is not interchangeable with a modern low-voltage, rail-to-rail amplifier. Decoupling capacitors, feedback resistor selection, source and load impedances, and stability conditions determine practical bandwidth. Use the manufacturer datasheet and its evaluated application circuits to select compensation and confirm performance across the required gain and frequency range. This page combines the verified manufacturer and distributor product information with engineering-focused comparisons, application guidance, package details, and design notes. It highlights where the OPA843ID's bandwidth, slew rate, supply range, and low-distortion voltage-feedback architecture are most useful, while also identifying the information that must be checked in the datasheet before a drop-in PCB or production design is approved.
OPA846ID - 1.75GHz Wideband Voltage-Feedback Op Amp | TI
Texas Instruments OPA846ID is a wideband, low-noise voltage-feedback operational amplifier with 1.75 GHz gain-bandwidth product, approximately 400 MHz bandwidth, and 625 V/us slew rate. The device is supplied in an 8-pin SOIC package and consumes 12.6 mA of supply current. Its combination of high speed, low input voltage noise, and strong large-signal performance makes it suitable for signal conditioning, active filtering, data acquisition, communications, and high-frequency instrumentation. A voltage-feedback operational amplifier is a gain-control device whose closed-loop bandwidth depends primarily on the noise gain selected by the feedback network. Unlike a current-feedback amplifier, a voltage-feedback amplifier maintains a defined gain relationship through its inverting and non-inverting inputs. The OPA846 combines this familiar topology with very high gain-bandwidth product and large-signal output drive, placing it within the high-speed analog amplifier category of the broader semiconductor and signal-processing hierarchy. The principal features of the OPA846ID include a 1.75 GHz gain-bandwidth product, approximately 400 MHz amplifier bandwidth, 625 V/us slew rate, and low 12.6 mA supply current. The low-noise architecture is suitable for systems in which the amplifier must preserve small signals while operating at high frequencies. Its low distortion and high output-drive capability also make it more useful than a general-purpose precision op amp in video, communications, and instrumentation signal paths. Internally, the OPA846 uses a classical differential input stage, two stages of forward gain, and a high-power output stage. This architecture combines low input-voltage noise with high bandwidth and large-signal performance. The differential stage provides the low-noise input behavior, the forward-gain stages establish the high gain-bandwidth product, and the output stage supplies the current needed to drive downstream circuits while maintaining low distortion. The manufacturer identifies the device as a single-circuit, voltage-feedback amplifier. Typical applications include wideband active filters, video-signal conditioning, ultrasound and medical instrumentation, communications receivers, test-equipment front ends, and clock or data-processing interfaces. In these applications, the 1.75 GHz gain-bandwidth product supports operation at high closed-loop gains when the feedback network is designed carefully. The 625 V/us slew rate allows the output to track large-amplitude, high-frequency signals, while low noise helps preserve weak signals ahead of later amplification or conversion stages. Designers should account for the bandwidth and stability consequences of the selected gain. The feedback resistors and compensation network determine the effective noise gain, and parasitic capacitance around the high-speed amplifier can alter stability. Short feedback paths, careful grounding, controlled impedance routing, and clean supply decoupling are particularly important at the bandwidth levels supported by this device. Component selection must also preserve adequate phase margin at the intended closed-loop gain and signal amplitude. OPA846ID is ordered in an 8-pin SOIC package with an operating temperature range of -40°C to +85°C. This page combines manufacturer specifications, sourcing information, drop-in candidate review, comparison data, and practical high-speed layout guidance to support component selection and board-level implementation.
OPA847ID - 3.9GHz Ultra-Low-Noise Op Amp | Texas Instruments
The Texas Instruments OPA847ID is a wideband, ultra-low-noise, voltage-feedback operational amplifier with shutdown capability, optimized for high-speed signal-chain applications. The device operates at up to 3.9 GHz, provides 0.85 nV/√Hz input-noise voltage density, and is available in an 8-SOIC package. Its combination of bandwidth, low noise, and an optional shutdown function makes it suitable for instrumentation, communications, test and measurement, video, and high-speed analog signal-processing systems. An operational amplifier is an active analog component that provides voltage amplification and signal buffering within a feedback network. Voltage-feedback operational amplifiers use the inverting input as the primary high-frequency feedback node, making them suitable for closed-loop gains ranging from low-level instrumentation to high-speed communications. The OPA847 belongs to the broader hierarchy of analog amplifiers, signal-chain ICs, and power-management-independent semiconductor components. The OPA847ID combines 3.9 GHz gain-bandwidth performance with 0.85 nV/√Hz input-noise voltage density. Its 18 mA supply current supports low-power operation compared with many wideband amplifiers, while the shutdown pin can disable the amplifier when power reduction is required. The device is designed for applications where preserving signal fidelity and bandwidth is more important than using a general-purpose precision amplifier. Because the OPA847 is a voltage-feedback amplifier, feedback-network design, source impedance, output loading, and trace geometry determine practical performance. The manufacturer datasheet describes operation with resistive feedback and recommends careful attention to high-frequency stability and output loading. The 8-SOIC package provides a compact surface-mount implementation, but decoupling and layout discipline remain essential when using the amplifier at high bandwidth. Typical uses include high-impedance instrumentation buffers, broadband transimpedance stages, RF and IF signal conditioning, communications receivers, video electronics, precision test equipment, and low-noise signal acquisition. The shutdown function is useful in portable or intermittently powered systems where the amplifier does not need to remain active continuously. When placing the OPA847ID, keep power-supply bypass capacitors close to the supply pins, provide a low-inductance return path, and route high-speed feedback and signal traces away from noisy switching nodes. Confirm output loading and feedback resistor values against the datasheet before operating near the device's upper bandwidth range. This product page combines the manufacturer's OPA847 documentation, distributor package information, operating specifications, practical layout guidance, and same-package replacement guidance. It helps engineers distinguish the OPA847ID from lower-bandwidth or noisier alternatives while keeping the focus on pin compatibility, bandwidth, noise performance, and application fit.
OPA858QIDSGRQ1 - 5.5GHz FET-Input TIA Op-Amp Q1 | TI
The Texas Instruments OPA858QIDSGRQ1 is an automotive-qualified (AEC-Q100), wideband, low-noise decompensated operational amplifier with FET (CMOS) inputs, delivering a 5.5-GHz gain bandwidth product (GBWP) while remaining stable at a minimum gain of 7 V/V. It is supplied in a compact 8-pin WSON (2x2 mm) surface-mount package. A decompensated amplifier is an operational amplifier internally compensated for stable operation only above a minimum closed-loop gain (here 7 V/V). By removing the compensation for unity-gain stability, the decompensated topology achieves dramatically higher bandwidth and lower input-referred noise than unity-gain-stable amplifiers of comparable process technology. In the signal-chain hierarchy, the OPA858-Q1 sits as a wideband voltage-feedback amplifier serving transimpedance amplifier (TIA) and high-gain voltage amplifier roles in high-speed analog front ends. Key features include the 5.5-GHz GBWP that enables high closed-loop bandwidths at transimpedance gains in the range of tens to hundreds of kilo-ohms, FET inputs that minimize input bias current effects on photodiode and high-impedance nodes, and single-ended single-channel configuration optimized for high-speed signal paths. The Q1 variant is manufactured on TI automotive flows and is qualified per AEC-Q100, supporting automotive lidar, imaging, and test applications that demand supply-chain traceability and automotive-grade reliability. The architecture combines CMOS input devices with wideband voltage-feedback internals, yielding low input capacitance that is critical in TIA designs because photodiode plus amplifier input capacitance directly limits achievable bandwidth per unit of transimpedance gain. TI provides the OPA858 together with a companion evaluation module and application collateral covering feedback resistor selection, compensation capacitor sizing, and stability analysis. Typical applications include automotive lidar receiver TIAs, wideband photodiode amplification in optical sensing, high-speed voltage amplification stages, and wideband test and measurement front ends. The device suits any signal chain that requires gain of 7 V/V or higher with multi-hundred-megahertz to gigahertz-class bandwidth. Design consideration: because the amplifier is only stable at gain >= 7 V/V, noise-gain analysis must be performed at all frequencies, including input capacitance effects at the inverting node; verify phase margin with the TI datasheet stability curves before finalizing feedback-network values.
OPA860ID - 370MHz Wide-Bandwidth OTA & Buffer | Texas Instruments
The Texas Instruments OPA860ID is a single-channel, wide-bandwidth operational transconductance amplifier and voltage buffer packaged in an 8-pin SOIC. It combines a bipolar operational transconductance amplifier (OTA) with a unity-gain buffer output, providing a 370 MHz bandwidth and approximately -4.2 V to +4.2 V output swing on a single +5 V supply. An operational transconductance amplifier is an amplifier whose output current is controlled by an input voltage. In signal-path terms, an OTA belongs to the operational-amplifier family, but it transfers current rather than presenting a conventional voltage output. The OPA860ID also contains a wide-band voltage buffer that can follow the OTA output, giving designers both transconductance and buffered-voltage operating modes in one package. The principal feature of the OPA860ID is its 370 MHz small-signal bandwidth. This bandwidth supports high-speed video, RF, and intermediate-frequency signal chains where the transconductance stage must amplify small control or error signals without excessive delay. The OTA can also be used as a current-output stage, while the internal buffer supplies a low-impedance voltage output when the system requires conventional signal routing. Because the device combines an OTA and a buffer, the circuit designer can select the more appropriate output stage for a given application. The OTA section operates as a voltage-controlled current source, while the buffer section provides a conventional voltage output. This versatility is useful in video and RF systems that evaluate gain, impedance, and loading behavior during prototype development. Typical uses include high-performance video processing, RF and IF signal conditioning, current-feedback and transconductance-based filter stages, laboratory instrumentation, and wideband analog signal chains. The single +5 V supply arrangement simplifies system design compared with dual-supply analog circuits, although output headroom must remain within the approximately -4.2 V to +4.2 V swing limits. PCB layout should prioritize short, controlled-impedance traces at the high-impedance OTA input. Keep the signal and ground paths compact, place bypassing capacitors close to the supply pins, and avoid long traces adjacent to switching nodes. These layout practices limit parasitic capacitance, reduce unintended feedback, and preserve the wideband behavior that distinguishes the OPA860 from ordinary low-frequency operational amplifiers. This page organizes the OPA860ID electrical characteristics, package information, application guidance, and verified alternatives into a design-focused reference. It also compares the available orderable family members so engineers can assess drop-in reuse while accounting for supply configuration, output-current capability, bandwidth, and package differences.
OPA861ID - 80 MHz Wide-Bandwidth OTA | Texas Instruments
The Texas Instruments OPA861ID is a wide-bandwidth operational transconductance amplifier (OTA) with an 80 MHz characteristic bandwidth, packaged in an 8-pin SOIC. It is a bipolar analog IC intended for signal-processing circuits that require voltage-to-current conversion rather than conventional voltage-output operational-amplifier behavior. The OPA861ID is associated with high-performance video, RF, and IF signal chains, where a transconductance element can provide controlled current drive, programmable gain, and analog signal conditioning. An operational transconductance amplifier is a voltage-controlled current-source building block. Its differential input voltage is converted into an output current that is proportional to the input and determined by the transconductance gain. In the OPA861 family, the manufacturer describes the device as a versatile monolithic wideband bipolar OTA. The OTA is therefore positioned above basic passive and discrete signal-conditioning components in the hierarchy of analog signal-processing ICs, while remaining a specialized alternative to a conventional operational amplifier. The key headline characteristics of the OPA861ID are its 80 MHz bandwidth designation, bipolar implementation, wide-bandwidth transconductance operation, and 8-pin SOIC package. These attributes make the device suitable for wideband analog systems in which signal bandwidth and controlled current output are more important than the familiar voltage-output architecture of an ordinary op amp. The 8-SOIC format also supports conventional surface-mount PCB assembly and routing, although the exact footprint dimensions and exposed-pad details should be checked against the package drawing. OPA861ID applications include RF and intermediate-frequency signal conditioning, high-performance video circuits, current-feedback filtering, analog gain-control paths, and instrumentation requiring a voltage-to-current conversion stage. In an RF or IF chain, the OTA can operate within a feedback loop that establishes filtering or gain, allowing the amplifier's transconductance behavior to be used as an active analog building block. In video systems, the wide-bandwidth characteristic supports higher-frequency signal paths than a general-purpose precision op amp. Designers should treat the OPA861ID as a high-speed analog device rather than a generic voltage regulator or precision low-noise amplifier. Input and feedback component selection, signal amplitude, supply headroom, and output-current limits must be evaluated together. The OPA861ID datasheet and its OTA section should be used to establish the exact recommended operating conditions, compensation approach, and application-circuit topology.
OPA890ID - 130MHz, 500V/us Single Op Amp | Texas Instruments
Texas Instruments OPA890ID is a low-power, wideband, single voltage-feedback operational amplifier with a disable function, one amplifier per package, a 130 MHz gain-bandwidth product, and a 500 V/us slew rate. Designed for low-voltage operation, the device accepts supply voltages from ±1.5 V to ±6 V and is offered in an 8-pin SOIC package. A voltage-feedback operational amplifier is an analog signal-conditioning amplifier that uses negative feedback to control gain and bandwidth. The OPA890ID belongs to the operational-amplifier hierarchy and is suitable for precision analog, communications, instrumentation, and signal-processing systems requiring much greater bandwidth than general-purpose amplifiers. Key characteristics include a 130 MHz gain-bandwidth product, 500 V/us slew rate, single-amplifier configuration, and an operating supply range of ±1.5 V to ±6 V. The wide bandwidth enables closed-loop operation at high frequencies, while the high slew rate supports accurate reproduction of rapidly changing waveforms. The shutdown function allows the amplifier to be disabled when a circuit does not require continuous operation. The OPA890ID uses a voltage-feedback architecture, which provides a direct relationship between input differential voltage and output voltage through the external feedback network. Its bandwidth and slew-rate characteristics make it appropriate for low-amplitude, high-speed signal paths rather than slow precision-only applications. Designers must account for gain-bandwidth interaction, output-voltage swing, input common-mode range, stability, and the effect of parasitic capacitance at high frequencies. Typical uses include video and communications signal conditioning, waveform generation, data-conversion interfaces, active filters, and low-level instrumentation. The disable pin can support power management or isolate an amplifier during selected operating modes. In dual-supply systems, the ±1.5 V to ±6 V capability permits operation from low-rail analog and mixed-signal supplies. PCB implementation should minimize trace length around the feedback network, maintain symmetrical routing, provide a solid ground reference, and place decoupling capacitors close to the supply pins. Feedback-component values should be checked against the selected closed-loop gain and the device's stability requirements. This page combines ordering information, verified electrical details, comparison guidance, and practical high-frequency layout considerations.
PAM8302A - 2.5W Filterless Class-D Mono Audio Amplifier | Diodes Incorporated
The Diodes Incorporated PAM8302A is a 2.5 W filterless Class-D mono audio amplifier housed in an 8-pin MSOP package, with an additional SOP-8 option. Its CMOS architecture drives 4 ohm or 8 ohm speakers directly without low-pass output filters, saving PCB area and BOM cost while delivering high-quality, low-THD audio reproduction. An audio amplifier is an electronic integrated circuit that boosts a low-power audio input signal to a level capable of driving a loudspeaker or headphones. The Class-D topology uses pulse-width modulation (PWM) to switch the output transistors fully on or fully off, achieving much higher efficiency (typically >85%) than linear Class-AB amplifiers (typically <60%). Within the broader taxonomy, the PAM8302A sits in the audio amplifier IC category, a subset of amplifier ICs, which belong to the signal chain and power management product families. Filterless Class-D amplifiers are particularly valued in portable, battery-powered designs because they eliminate bulky LC output filter networks, reducing both board area and cost. Key specifications include a 2.5 W continuous output power into 4 ohm at 10% THD from a 5.5 V supply, low THD+N of 0.10% at 1 W into 8 ohm, a wide 2.0 V to 5.5 V supply range, integrated undervoltage lockout at 2.1 V, and a low shutdown current. The MSOP-8 (with thermal pad) footprint offers a compact 3.0 mm x 3.0 mm outline suitable for handheld devices, while the SOP-8 (PAM8302AADCR) variant serves designs requiring through-hole-compatible footprints. Built-in short-circuit protection and thermal shutdown further enhance robustness in consumer applications. The PAM8302A employs a fully-differential PWM modulator with proprietary filterless modulation, which eliminates the traditional LC reconstruction filter while maintaining acceptable EMI through controlled edge-rate switching and spread-spectrum techniques. The differential input topology also rejects common-mode noise from upstream audio DACs or PWM sources. Typical applications include portable Bluetooth speakers, handheld gaming consoles, alarm clocks, intercom systems, toys, and any cost-sensitive battery-powered device requiring moderate audio output. Designers frequently choose this part for retrofit audio upgrades in retro gaming hardware, single-board computers, and IoT devices where PCB area is at a premium. When designing with the PAM8302A, ensure adequate power supply bulk decoupling (typically 10 uF) close to the AVDD/PVDD pins to minimize THD. The SD pin (active-low shutdown) must be tied high for normal operation or controlled via a GPIO for power sequencing. Reserve sufficient copper pour on the exposed thermal pad to dissipate Class-D switching losses, especially at full 2.5 W output. This page synthesizes distributor pricing, verified drop-in alternatives, and application-specific design notes not found in the manufacturer datasheet alone, making it a practical engineering reference for sourcing and design.
PAM8403 - 3W Filterless Class-D Stereo Audio Amplifier | Diodes Incorporated
The Diodes Incorporated PAM8403 is a 3 W filterless Class-D stereo audio amplifier delivered in a 16-pin SOP package, operating from a 2.5 V to 5.5 V single supply. Each channel delivers 3 W into a 4 ohm load at 10% THD+N with a 5 V power supply, while maintaining efficiency up to 90% thanks to the Class-D switching topology. The device integrates a bridge-tied load (BTL) output stage that removes the need for external LC low-pass filters on the speaker lines, saving PCB area and BOM cost in stereo and mono consumer audio designs. A Class-D audio amplifier is a switching amplifier topology that uses pulse-width modulation at a switching frequency far above the audio band to recreate the input waveform. Compared with Class-AB linear amplifiers, Class-D parts achieve much higher efficiency (often >85%), which reduces power dissipation in portable and battery-powered applications. The PAM8403 belongs to the audio amplifier IC family, which itself sits inside the broader amplifier IC and integrated circuit hierarchy used in consumer and prosumer audio products. Key features include low THD+N for high-quality sound reproduction, a typical 90% efficiency figure that extends battery life in portable applications, and integrated protection such as short-circuit and thermal shutdown. The shutdown pin (SD) can drive the amplifier into a low-current mute state, and the device also provides a noise-free power-up/power-down cycle that eliminates audible pops. Available only in the SOP-16 package, the part is aimed at compact stereo speaker implementations where board real estate is at a premium. Typical applications include LCD TV and monitor speaker drivers, portable and Bluetooth speaker enclosures, laptop docking stations, DVD and game console line outputs, and phone / speakerphone accessories. Its filterless architecture allows very short, direct PCB traces from the IC outputs to the speakers, simplifying the layout versus traditional Class-D solutions that need an LC reconstruction filter. When designing with the PAM8403, place the supply decoupling capacitors as close to the VDDP and VDDL pins as possible, use a ferrite bead on the speaker outputs if extra EMI suppression is required, and respect the maximum junction temperature rating to avoid thermal shutdown during sustained high-output conditions. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes that are not found in the standalone manufacturer datasheet PDF, including PCB layout and EMI considerations specific to filterless Class-D designs.
PGA206UA - 5MHz FET-Input Programmable Gain In-Amp | TI
The Texas Instruments PGA206UA is a high-speed digitally programmable gain instrumentation amplifier (PGA) delivering a 5 MHz bandwidth, 100 pA maximum FET-input bias current, and digitally selectable gains of 1, 2, 4, and 8 V/V in a 16-pin SOIC (SOL-16) surface-mount package. A programmable gain instrumentation amplifier is a precision differential amplifier whose closed-loop gain is set by digital control inputs rather than external resistors. It sits within the amplifier hierarchy as an instrumentation amplifier -> precision op amp -> analog front-end (AFE) -> signal chain IC, combining a true three-architectural-input instrumentation amplifier front end with internally switched gain networks. PGAs are essential in data acquisition systems where a single amplifier must handle sensor signals spanning several orders of magnitude without manual range switching. Key features include fast settling to 0.01% after a gain change, +/-40V input protection that survives overrange faults common in industrial field wiring, and a low maximum offset voltage of 1.5 mV. The FET input stage keeps bias current at 100 pA max, preserving accuracy with high-impedance sources such as pH probes, photodiodes, and piezoelectric sensors. Technically, the PGA206 uses internally switched precision resistor networks controlled by two digital gain-select lines, a scheme the datasheet notes pairs naturally with an external logic latch to acquire gain data from a high-speed digital bus. Slew rate is 25 V/us and the supply range is +/-4.5V to +/-18V, allowing operation from standard +/-5V, +/-12V, or +/-15V analog rails. Operation is specified from -40C to +85C. Typical applications include multi-range data acquisition front ends, programmable sensor interfaces, test and measurement instrumentation, and dynamic signal conditioning where gain must change on-the-fly between measurements. Design consideration: total response time after a gain change equals the switching time plus the settling time to the new output voltage, so budget for settling in high-throughput scanning systems. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
PGA207UA - 5MHz Programmable Gain Instrumentation Amp | TI
The Texas Instruments PGA207UA is a high-speed digitally programmable gain instrumentation amplifier offering a 5 MHz bandwidth, 100 pA maximum FET-input bias current, and digitally selectable gains of 1, 2, 5, and 10 V/V, housed in a 16-pin SOIC (SOL-16) surface-mount package. A programmable gain instrumentation amplifier (PGIA) is a precision differential amplifier whose closed-loop gain is set digitally rather than by external resistors. In the signal-chain hierarchy it sits between sensors and data converters, combining the true instrumentation-amplifier input stage (high common-mode rejection, balanced high-impedance inputs) with gain-switching logic, so a single ADC channel can resolve signals spanning several orders of magnitude. Key features of the PGA207 include two CMOS/TTL-compatible address lines for gain selection, analog inputs internally protected against overloads up to +/-40V even with the supplies off, and laser-trimmed offset voltage for low drift. A fast 0.01% settling specification allows the gain to be switched between conversions in high-throughput data-acquisition systems without dead time. Architecturally, the device uses a three-amplifier instrumentation topology with FET input transistors, giving negligible input bias current (100 pA max) for high-source-impedance sensors, a 25 V/us slew rate, and 18 nV/sqrt(Hz) input noise with 75 dB CMRR. Laser trimming at the Burr-Brown production line holds offset voltage to 1.5 mV max, preserving accuracy at the lowest gains. Typical applications include programmable data-acquisition front ends, dynamic signal ranges from PT100 sensors and strain-gauge bridges, test and measurement instrumentation, and industrial process-control analog front ends feeding 12- to 16-bit ADCs. When designing, remember the gain lines are logic-level inputs: tie them to clean CMOS/TTL levels and route away from the input traces. The +/-40V input protection removes the need for external clamp diodes in most industrial environments. This page consolidates distributor pricing, drop-in family alternatives, and engineering design guidance not found in a single manufacturer datasheet page.
PGA207UA/1K - 5MHz Programmable Gain In-Amp | Texas Instruments
The Texas Instruments PGA207UA/1K is a high-speed, digitally programmable gain instrumentation amplifier delivering gains of 1, 2, 5, and 10 V/V with a 5 MHz bandwidth, a FET input stage with 100 pA maximum bias current, and a 16-pin SOL-16 SOIC surface-mount package. A programmable gain instrumentation amplifier (PGIA) is a precision differential amplifier whose closed-loop gain is set digitally rather than by external resistors. Within the signal-chain hierarchy, it sits between raw transducers and ADCs as a front-end conditioning device, combining the high input impedance and CMRR of a true three-op-amp instrumentation amplifier with gain-switching logic that lets one device serve multiple transducer full-scale ranges. Key features of the PGA207UA/1K include digitally selectable gains (1, 2, 5, 10 V/V) via two CMOS/TTL-compatible address lines, fast settling to 0.01%, a FET input with maximum bias current of 100 pA, and internal input protection rated for plus/minus 40V overloads even with power supplies off. The device is laser-trimmed for low offset voltage (1.5 mV max) and low drift, eliminating manual calibration in most data acquisition designs. Technically, the PGA207 architecture uses a true instrumentation amplifier input stage whose gain is switched by the two digital address lines, so no external gain resistors are needed and gain accuracy is factory-determined. The 5 MHz bandwidth at higher gains supports multiplexed data acquisition channels, while the FET input minimizes loading on high-impedance sources such as photodiodes and piezoelectric sensors. Supply operation spans plus/minus 4.5V to plus/minus 18V, with a slew rate of approximately 25 V/us. Typical applications include multiplexed data acquisition front ends, programmable test and measurement signal conditioning, and industrial sensor interfaces where input channels of different amplitude must share one ADC. Fast settling allows channel-to-channel switching without long dead time, improving system throughput. Design consideration: ensure supply headroom within the plus/minus 4.5V to plus/minus 18V range and route the digital gain-select lines away from the high-impedance inputs to prevent digital noise coupling into the analog front end. This page synthesizes distributor pricing, drop-in family alternatives, comparison data, and practical design notes not found in the manufacturer datasheet.
PGA281 - Zero-Drift Programmable Gain Instrumentation Amplifier | TI
The PGA281 is a high-precision instrumentation amplifier from Texas Instruments featuring digitally-controllable gain and signal-integrity test capability. It uses proprietary autozeroing techniques to achieve low offset voltage, near-zero offset and gain drift, excellent linearity, and nearly no 1/f noise. The device is available in a 16-pin TSSOP package (PW) and operates over a wide supply range, making it suitable for precision sensor interfaces and data acquisition systems. An instrumentation amplifier (INA) is a type of differential amplifier that amplifies the difference between two input signals while rejecting common-mode voltages. It is characterized by high input impedance, high common-mode rejection ratio (CMRR), and low offset voltage. The PGA281 belongs to the family of programmable gain instrumentation amplifiers (PGIAs), which allow the gain to be set digitally or via external resistors, providing flexibility in signal conditioning chains. This category sits within the broader hierarchy of analog amplifiers, which are essential building blocks in electronic systems for signal conditioning and measurement. Key features of the PGA281 include gain programmable from G = 0.2 to 10,000 using an external resistor, fully differential outputs with integrated clamping, low offset voltage of 10 µV (typ) and 35 µV (max), low offset drift of 0.1 µV/°C (typ) and 0.3 µV/°C (max), and low input bias current of 5 pA (typ). These specifications make it ideal for high-accuracy applications where drift and noise are critical. The PGA281 employs a zero-drift architecture that continuously corrects offset and drift, achieving near-zero temperature coefficients. The integrated clamping circuitry protects the outputs from overvoltage conditions, enhancing system robustness. The device supports a wide supply range, typically ±5V, and provides rail-to-rail output swing, maximizing dynamic range. Typical applications include precision current sensing (10 µA to 100 mA), sensor signal conditioning for bridge sensors, thermocouple amplifiers, and data acquisition front-ends. Its low offset and drift make it suitable for medical instrumentation, industrial process control, and test and measurement equipment. When designing with the PGA281, ensure proper decoupling of the power supply pins and consider the thermal performance of the TSSOP package. The gain-setting resistor should be a precision resistor to maintain gain accuracy. The device's signal-integrity test capability allows for system-level diagnostics, which is valuable in safety-critical applications.
SGM8955XN5G - Zero-Drift Op Amp, 1-Ch, SOT-23-5 | SG Micro
The SG Micro SGM8955XN5G is a single-channel, micro-power, CMOS zero-drift operational amplifier housed in a 5-pin SOT-23-5 (XN5) surface-mount package. It delivers a 22 µV (MAX) offset voltage with 80 nV/°C offset drift, 100 dB open-loop gain, and 130 pA input bias current, optimized for precision signal chains operating from low-voltage rails. An operational amplifier (op amp) is a high-gain differential DC amplifier that uses external feedback components to set gain, bandwidth, and transfer characteristics. Zero-drift op amps employ either chopper or auto-zero (chopper-stabilized) architectures to continuously correct offset voltage, eliminating the 1/f flicker noise and offset drift that plague conventional CMOS and bipolar input stages. The SGM8955 belongs to the precision amplifier category within the broader linear IC hierarchy: operational amplifier → amplifier IC → analog signal chain → semiconductor. Key features of the SGM8955XN5G include a 20 µA typical quiescent supply current, 180 V/ms slew rate, rail-to-rail input and rail-to-rail output (RRIO) swing, EMI filtering/RF suppression on the inputs, and an integrated auto-zero calibration loop. The SOT-23-5 (XN5) package operates across -40 °C to +125 °C and supports supply voltages suitable for 2.7 V-5.5 V single-supply systems. The combination of low offset, low drift, low power, and RRIO makes the part a strong fit for battery-powered instrumentation, transducer conditioning, and precision ADC front ends. The SGM8955/6 architecture uses a chopper-stabilized CMOS input stage to achieve sub-50 µV offset, eliminating the periodic recalibration required by conventional CMOS amplifiers in precision applications. The internal EMI/RF input filter rejects high-frequency interference, simplifying PCB layout for sensor applications in electrically noisy environments. The 20 µA quiescent current and low shutdown leakage allow the part to remain continuously powered in battery applications without significantly reducing runtime. Typical applications include high-precision ADC driver circuits, weigh scale and strain gauge signal conditioning, thermocouple and bridge sensor amplifiers, portable medical instrumentation, battery-powered industrial sensors, and zero-drift transducer interfaces. The RRIO capability allows the part to operate at unity gain in single-supply systems where input and output signals swing close to either supply rail. When designing with the SGM8955XN5G, place the input capacitor as close to the op-amp input pins as possible, ensure the feedback network uses 1% or better resistors to maintain gain accuracy, and add an anti-aliasing RC network at the output when driving a downstream ADC. Estimated: total supply current is the sum of the 20 µA quiescent plus the load-dependent output stage current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
SI8921BD-IS4 - ±250 mV Isolated Amplifier, 5 kV | Skyworks
The Skyworks Solutions SI8921BD-IS4 is a galvanically isolated analog amplifier with a ±250 mV differential input range, 5.0 kV RMS isolation rating, and differential output, housed in a wide-body stretched SOIC-8 package. Key headline specifications include 0.8 µs signal delay, ±0.40 µV typical input offset, ±0.06% typical gain error, 0.5 µV/°C offset drift, and -9 ppm/°C typical gain drift, providing accurate current-shunt measurement across industrial temperature ranges. An isolated amplifier is a type of analog amplifier that combines a precision front-end differential amplifier with a galvanic isolation barrier, transferring the signal across the barrier through capacitive or transformer coupling. The isolation barrier protects low-voltage control circuitry from high-voltage common-mode transients on the field side, enabling safe measurement of floating signals such as those present across current-shunt resistors in motor drives, solar inverters, and uninterruptible power supplies. Within the broader hierarchy, an isolated amplifier belongs to the isolation IC family, which includes digital isolators and isolated gate drivers - all of which form essential building blocks in power-management and industrial-automation systems requiring reinforced insulation per IEC 60747-17 and UL 1577. The SI8921BD-IS4 features a specified input range of ±250 mV, well suited for direct connection across low-ohm shunt resistors in high-current paths. Its differential output swings to a 2.5 V peak full-scale signal, which can be fed directly into the ADC front-end of a motor controller or power-conversion MCU. The device's low offset and drift specifications eliminate the need for periodic calibration in many systems, while its 0.8 µs propagation delay supports closed-loop current control in fast-switching converters. Architecturally, the SI8921BD-IS4 integrates a precision chopper-stabilized input amplifier, a sigma-delta modulator, an isolation capacitor barrier, and a differential output decoder on the low-voltage side. The internal LDO regulators on both sides of the barrier simplify power-supply design - the high-side is powered from a 3.0 V to 5.5 V supply, and the low-side is powered independently from 3.0 V to 5.5 V. The CMOS output stage is capable of driving 2 kΩ loads with low distortion. Typical applications include current-shunt monitoring in three-phase motor drives, photovoltaic inverter string-current sensing, UPS battery-current measurement, industrial process-control isolation, and high-voltage rail monitoring in telecom rectifiers. The differential output interfaces directly with SAR ADCs and sigma-delta converters found in C2000 and PIC32 families. When designing with this device, place bypass capacitors of 0.1 µF and 1 µF close to both VDDA and VDDD pins, keep the input traces short and balanced to preserve CMRR, and observe the creepage and clearance rules of the wide-body SOIC-8 footprint to maintain the 5 kV isolation rating. The differential output should be routed as a matched pair to avoid common-mode pickup in noisy switching environments. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on a single manufacturer product page or distributor listing.
SSM2141PZ - Differential Line Receiver, 100dB CMR, 3MHz | ADI
The Analog Devices SSM2141PZ is an integrated differential line receiver (audio amplifier, Class AB) designed to receive balanced line inputs in professional audio applications requiring high noise immunity and optimum common-mode rejection. Housed in an 8-pin PDIP (PZ) package, it operates from dual supplies of ±6V to ±18V and typically achieves 100 dB of common-mode rejection (CMR) at DC and 60 Hz, far exceeding the ~40 dB CMR achievable with a generic op amp and four discrete precision resistors. The device delivers 0.001% typical THD, a fast 10 V/us slew rate, and a wide 3 MHz small-signal bandwidth. A balanced line receiver is a specialized analog building block that accepts a differential signal riding on a common-mode voltage (such as the long cable run from a stage to a mixing console) and converts it to a single-ended, ground-referenced output while rejecting the common-mode noise picked up along the way. In the audio signal chain hierarchy, the SSM2141 sits between the input connector / XLR stage and downstream ADC or line-level processing; it is part of the broader family of audio amplifiers and instrumentation amplifiers used in pro-audio and broadcast equipment. Key differentiating specifications include 100 dB CMR (DC, typ), 70 dB CMR at 20 kHz and 62 dB at 40 kHz, 0.001% THD+N, 10 V/us slew rate, 3 MHz bandwidth, and a 600 ohm minimum load. Internal thin-film resistor networks are laser-trimmed to deliver matching that no off-the-shelf 0.1% discrete resistor approach can match at production volume, which is what enables the headline CMR figure. Typical applications include balanced audio line receivers in mixing consoles and stage boxes, AES3 / EBU receiver front-ends, audio distribution amplifiers, and instrumentation front-ends where high DC and AC common-mode rejection is required. The 600 ohm load rating and +22 dBu headroom make it directly compatible with broadcast and studio analog line-level standards. When designing with the SSM2141PZ, treat the gain-setting resistor (typically 10 kohm between pins 1 and 8 for unity gain) as a low-noise, low-drift metal-film part to preserve CMR. Add 100 ohm series output resistors plus 10 nF to ground at each output if cable capacitance will exceed ~1000 pF, to prevent oscillation. Decouple both supply pins with 0.1 uF ceramic in parallel with 10 uF tantalum or electrolytic, placed within 5 mm of the package. This page synthesizes distributor pricing, drop-in alternatives, and practical PCB layout notes not found in the manufacturer datasheet alone, including cross-brand substitutes from Texas Instruments and Maxim that share the same 8-pin PDIP footprint and equivalent CMR-class performance.