بەرهەمەکان (3,200+)

THS7314D - 3-Channel SDTV Video Amplifier | Texas Instruments
THS7314D

THS7314D - 3-Channel SDTV Video Amplifier | Texas Instruments

The Texas Instruments THS7314D is a 3-channel SDTV video amplifier with integrated fifth-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and combines three video channels in one package. According to the Texas Instruments product and data-sheet information, the device uses the Silicon-Germanium BiCom-III process and consumes 16 mA total quiescent current at 3.3 V. A video amplifier is an analog signal-chain component that conditions composite or component video signals between a source, processing stage, and display. It belongs to the amplifier hierarchy, specifically the video-amplifier and video-buffer category. Unlike a passive termination network, an integrated video amplifier can provide filtering, gain, impedance matching, and output-drive capability while reducing the number of discrete components required on a video board. The THS7314D provides three buffered channels, 6 dB gain, and fifth-order filtering in one 8-pin SOIC. Its rail-to-rail output stage supports both AC and DC line-driving requirements. The manufacturer specifically identifies driving two lines or 75-ohm loads as supported use cases, making the device relevant to SDTV routing, video distribution, and display-adapter designs. The integrated filter function is especially useful when system designers want repeatable channel filtering without external filter networks. Its low-power operation distinguishes the part from higher-current video drivers. Texas Instruments states that the total 16 mA quiescent current at a 3.3 V supply makes the THS7314 suitable for USB-powered, portable, and other power-sensitive video applications. The single-supply 3 V to 5 V operating range also allows the same architecture to operate from nominal 3.3 V and 5 V system rails, although the complete design must satisfy the limits in the manufacturer data sheet for each voltage and temperature condition. Typical applications include SDTV output buffering, video splitters and distribution boards, portable media equipment, video capture equipment, and display interfaces. In each case, the three-channel structure reduces routing complexity while the fifth-order filters and 6 dB gain support controlled signal transmission into downstream analog video stages. The 75-ohm drive capability is useful when the output must connect through conventional video cabling to a terminated load. Designers should verify the complete pin configuration, decoupling requirements, input and output impedance, bandwidth, channel-to-channel behavior, and recommended termination network against the official data sheet. Video-layout practices should also be considered, including short trace routing, careful grounding, separation between analog video paths and noisy switching circuitry, and appropriate filtering at external connectors. This page consolidates the verified manufacturer and distributor information for THS7314D and clearly identifies parameters for which verified values were not supplied. It also distinguishes the confirmed device characteristics from engineering information that must be obtained from the official THS7314 data sheet before layout or qualification decisions are finalized.

RFQ پەیوەندی
THS7314DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7314DR

THS7314DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments THS7314DR is a 3-channel SDTV video amplifier with integrated fifth-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and combines three video channels in one package. According to the Texas Instruments product and data-sheet information, the device uses the Silicon-Germanium BiCom-III process and consumes 16 mA total quiescent current at 3.3 V. A video amplifier is an analog signal-chain component that conditions composite or component video signals between a source, processing stage, and display. It belongs to the amplifier hierarchy, specifically the video-amplifier and video-buffer category. Unlike a passive termination network, an integrated video amplifier can provide filtering, gain, impedance matching, and output-drive capability while reducing the number of discrete components required on a video board. The THS7314DR provides three buffered channels, 6 dB gain, and fifth-order filtering in one 8-pin SOIC. Its rail-to-rail output stage supports both AC and DC line-driving requirements. The manufacturer specifically identifies driving two lines or 75-ohm loads as supported use cases, making the device relevant to SDTV routing, video distribution, and display-adapter designs. The integrated filter function is especially useful when system designers want repeatable channel filtering without external filter networks. Its low-power operation distinguishes the part from higher-current video drivers. Texas Instruments states that the total 16 mA quiescent current at a 3.3 V supply makes the THS7314 suitable for USB-powered, portable, and other power-sensitive video applications. The single-supply 3 V to 5 V operating range also allows the same architecture to operate from nominal 3.3 V and 5 V system rails, although the complete design must satisfy the limits in the manufacturer data sheet for each voltage and temperature condition. Typical applications include SDTV output buffering, video splitters and distribution boards, portable media equipment, video capture equipment, and display interfaces. In each case, the three-channel structure reduces routing complexity while the fifth-order filters and 6 dB gain support controlled signal transmission into downstream analog video stages. The 75-ohm drive capability is useful when the output must connect through conventional video cabling to a terminated load. Designers should verify the complete pin configuration, decoupling requirements, input and output impedance, bandwidth, channel-to-channel behavior, and recommended termination network against the official data sheet. Video-layout practices should also be considered, including short trace routing, careful grounding, separation between analog video paths and noisy switching circuitry, and appropriate filtering at external connectors. This page consolidates the verified manufacturer and distributor information for THS7314DR and clearly identifies parameters for which verified values were not supplied. It also distinguishes the confirmed device characteristics from engineering information that must be obtained from the official THS7314 data sheet before layout or qualification decisions are finalized.

RFQ پەیوەندی
THS7315D - 3-Channel SDTV Video Amplifier | Texas Instruments
THS7315D

THS7315D - 3-Channel SDTV Video Amplifier | Texas Instruments

Texas Instruments THS7315D is a three-channel SDTV video amplifier with integrated fifth-order filters and 5.2 V/V gain, operating from a single 3 V to 5 V supply in an 8-SOIC package. The device combines three video channels, fixed 5.2 V/V gain, and fifth-order filtering for CVBS, S-Video, YPBPR 480i/576i, YUV, and GBR/RGB signal paths. A video amplifier is an analog signal-conditioning IC that increases the amplitude of composite or component video signals while controlling bandwidth, attenuation, and unwanted spectral content. Within the broader semiconductor hierarchy, the THS7315D is a video amplifier, a type of analog amplifier, and ultimately an integrated circuit used within display, broadcast, set-top-box, and video-conversion systems. The THS7315D integrates three independent SDTV video amplifier channels and fifth-order filters into one package. Its fixed gain of 5.2 V/V is useful when a source produces a relatively small video amplitude and the downstream circuitry requires additional signal swing. The fifth-order filters provide frequency-dependent noise and interference attenuation, while the single-supply architecture simplifies power planning in 3 V and 5 V systems. Texas Instruments fabricated the device using its complementary silicon-germanium BiCom3 process. This integration reduces the number of discrete amplification and filtering stages required in a multi-channel analog video path. Because the amplifier includes filters rather than functioning only as a wideband buffer, board-level signal integrity depends on correct source and load impedances, adequate bypass capacitance, short output routing, and proper grounding. The supplied data does not provide detailed output impedance, bandwidth, settling-time, noise, or stability-versus-capacitance figures, so those characteristics must be confirmed in the manufacturer datasheet before final circuit sign-off. Typical uses include SDTV video buffering, Y/Cb/Cr component-video distribution, CVBS and S-Video processing, RGB amplification, and DAC reconstruction filtering. The integrated three-channel arrangement is particularly useful when red, green, and blue or Y, Pb, and Pr channels must receive matched amplification and filtering. It can also support protected or industrial video equipment where reducing the number of active stages simplifies signal routing and maintenance. A primary design consideration is ensuring that the source impedance, termination, and downstream load remain compatible with the integrated filter network. The manufacturer's datasheet and typical application information should be used to select input and output coupling or termination components. PCB layout should keep the device and its bypass capacitors close together, maintain short analog traces, provide an uninterrupted ground reference, and isolate sensitive video paths from switching and high-current return paths. This product page consolidates the verified manufacturer and distributor information, distinguishes documented THS7315D characteristics from missing technical data, identifies verified same-package replacements, and adds practical application and layout guidance for engineers evaluating the THS7315D in SDTV video signal chains.

RFQ پەیوەندی
THS7315DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7315DR

THS7315DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)

Texas Instruments THS7315DR is a three-channel SDTV video amplifier with integrated fifth-order filters and 5.2 V/V gain, operating from a single 3 V to 5 V supply in an 8-SOIC package. The device combines three video channels, fixed 5.2 V/V gain, and fifth-order filtering for CVBS, S-Video, YPBPR 480i/576i, YUV, and GBR/RGB signal paths. A video amplifier is an analog signal-conditioning IC that increases the amplitude of composite or component video signals while controlling bandwidth, attenuation, and unwanted spectral content. Within the broader semiconductor hierarchy, the THS7315DR is a video amplifier, a type of analog amplifier, and ultimately an integrated circuit used within display, broadcast, set-top-box, and video-conversion systems. The THS7315DR integrates three independent SDTV video amplifier channels and fifth-order filters into one package. Its fixed gain of 5.2 V/V is useful when a source produces a relatively small video amplitude and the downstream circuitry requires additional signal swing. The fifth-order filters provide frequency-dependent noise and interference attenuation, while the single-supply architecture simplifies power planning in 3 V and 5 V systems. Texas Instruments fabricated the device using its complementary silicon-germanium BiCom3 process. This integration reduces the number of discrete amplification and filtering stages required in a multi-channel analog video path. Because the amplifier includes filters rather than functioning only as a wideband buffer, board-level signal integrity depends on correct source and load impedances, adequate bypass capacitance, short output routing, and proper grounding. The supplied data does not provide detailed output impedance, bandwidth, settling-time, noise, or stability-versus-capacitance figures, so those characteristics must be confirmed in the manufacturer datasheet before final circuit sign-off. Typical uses include SDTV video buffering, Y/Cb/Cr component-video distribution, CVBS and S-Video processing, RGB amplification, and DAC reconstruction filtering. The integrated three-channel arrangement is particularly useful when red, green, and blue or Y, Pb, and Pr channels must receive matched amplification and filtering. It can also support protected or industrial video equipment where reducing the number of active stages simplifies signal routing and maintenance. A primary design consideration is ensuring that the source impedance, termination, and downstream load remain compatible with the integrated filter network. The manufacturer's datasheet and typical application information should be used to select input and output coupling or termination components. PCB layout should keep the device and its bypass capacitors close together, maintain short analog traces, provide an uninterrupted ground reference, and isolate sensitive video paths from switching and high-current return paths. This product page consolidates the verified manufacturer and distributor information, distinguishes documented THS7315DR characteristics from missing technical data, identifies verified same-package replacements, and adds practical application and layout guidance for engineers evaluating the THS7315DR in SDTV video signal chains.

RFQ پەیوەندی
THS7316D - 3-Channel HDTV Video Amplifier | Texas Instruments
THS7316D

THS7316D - 3-Channel HDTV Video Amplifier | Texas Instruments

Texas Instruments THS7316D is a 3-channel HDTV video amplifier with integrated 5th-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and provides three buffered video channels for HDTV and related video-signal processing systems. The device is fabricated using the Silicon-Germanium (SiGe) BiCom-III process and is designed for low-power video applications where integrated filtering reduces external circuit complexity. A video amplifier is a specialized analog amplifier that buffers and conditions composite or component video signals while preserving usable bandwidth and signal amplitude. The THS7316 belongs to the broader video-amplifier and signal-conditioning category, integrating three amplifier channels with fixed filtering into one device. This makes it useful in set-top boxes, television equipment, video processors, projectors, displays, and other systems that distribute or convert analog video signals. The principal features of the THS7316D are its three-channel architecture, 6 dB voltage gain, 5th-order integrated filters, single-supply operation, and 43 MHz video bandwidth identified in the verified product data. The filter implementation helps remove unwanted high-frequency video components before they reach downstream circuitry. Its three-channel arrangement allows red, green, and blue video paths to be amplified consistently within one package, reducing the number of separate buffer devices required. The device uses a low-power SiGe BiCom-III process and is intended for 3 V to 5 V single-supply systems. The verified distributor description identifies the THS7316 as a 3-channel integrated video buffer, while the Texas Instruments product page identifies the 5th-order filter and 6 dB gain functions. The 8-SOIC package is compatible with conventional surface-mount assembly and is suitable for compact consumer and industrial video equipment. Typical applications include HDTV signal conditioning, RGB video distribution, video projection systems, television receivers, set-top-box video outputs, and industrial video interfaces. The integrated filtering is particularly useful where the source signal requires predictable bandwidth limiting before a display, encoder, scaler, or analog-to-digital conversion stage. The fixed 6 dB gain also provides a defined signal-conditioning function rather than requiring an external gain network for basic video buffering. Designers should verify the complete electrical limits, decoupling requirements, output loading, and filter response in the manufacturer datasheet before layout release. Pay particular attention to the single-supply input range, required bypass capacitors, and the acceptable input and output signal levels. Because the available verified data does not provide the complete pin mapping or all parameter values, the PCB footprint and analog signal path should be checked against the official THS7316 documentation rather than inferred from distributor descriptions. This page combines verified manufacturer and distributor information, source-backed technical context, and practical selection considerations for engineers evaluating the THS7316D. It also distinguishes verified attributes from parameters that remain to be confirmed in the datasheet, helping prevent assumptions about gain, bandwidth, filtering, or pin compatibility during component selection.

RFQ پەیوەندی
THS7316DR - 3-Channel HDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7316DR

THS7316DR - 3-Channel HDTV Video Amplifier | Texas Instruments (Tape & Reel)

Texas Instruments THS7316DR is a 3-channel HDTV video amplifier with integrated 5th-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and provides three buffered video channels for HDTV and related video-signal processing systems. The device is fabricated using the Silicon-Germanium (SiGe) BiCom-III process and is designed for low-power video applications where integrated filtering reduces external circuit complexity. A video amplifier is a specialized analog amplifier that buffers and conditions composite or component video signals while preserving usable bandwidth and signal amplitude. The THS7316 belongs to the broader video-amplifier and signal-conditioning category, integrating three amplifier channels with fixed filtering into one device. This makes it useful in set-top boxes, television equipment, video processors, projectors, displays, and other systems that distribute or convert analog video signals. The principal features of the THS7316DR are its three-channel architecture, 6 dB voltage gain, 5th-order integrated filters, single-supply operation, and 43 MHz video bandwidth identified in the verified product data. The filter implementation helps remove unwanted high-frequency video components before they reach downstream circuitry. Its three-channel arrangement allows red, green, and blue video paths to be amplified consistently within one package, reducing the number of separate buffer devices required. The device uses a low-power SiGe BiCom-III process and is intended for 3 V to 5 V single-supply systems. The verified distributor description identifies the THS7316 as a 3-channel integrated video buffer, while the Texas Instruments product page identifies the 5th-order filter and 6 dB gain functions. The 8-SOIC package is compatible with conventional surface-mount assembly and is suitable for compact consumer and industrial video equipment. Typical applications include HDTV signal conditioning, RGB video distribution, video projection systems, television receivers, set-top-box video outputs, and industrial video interfaces. The integrated filtering is particularly useful where the source signal requires predictable bandwidth limiting before a display, encoder, scaler, or analog-to-digital conversion stage. The fixed 6 dB gain also provides a defined signal-conditioning function rather than requiring an external gain network for basic video buffering. Designers should verify the complete electrical limits, decoupling requirements, output loading, and filter response in the manufacturer datasheet before layout release. Pay particular attention to the single-supply input range, required bypass capacitors, and the acceptable input and output signal levels. Because the available verified data does not provide the complete pin mapping or all parameter values, the PCB footprint and analog signal path should be checked against the official THS7316 documentation rather than inferred from distributor descriptions. This page combines verified manufacturer and distributor information, source-backed technical context, and practical selection considerations for engineers evaluating the THS7316DR. It also distinguishes verified attributes from parameters that remain to be confirmed in the datasheet, helping prevent assumptions about gain, bandwidth, filtering, or pin compatibility during component selection.

RFQ پەیوەندی
THS7353PW - 3-Channel I2C Video Amp | Texas Instruments
THS7353PW

THS7353PW - 3-Channel I2C Video Amp | Texas Instruments

Texas Instruments THS7353PW is a three-channel, low-power video amplifier with I2C control, selectable filters, 0 dB gain, and a 2:1 input multiplexer in a 20-pin TSSOP (PW) package. It operates from a single 2.7 V to 5 V supply and consumes 16.2 mA total quiescent current at a 3.3 V supply. A video amplifier, also called a video buffer, conditions analog video signals between source and destination stages. The THS7353 belongs to the broader integrated video-amplifier hierarchy, combining signal buffering, gain control, filtering, input selection, and serial configuration in one semiconductor. This integration reduces the number of discrete signal-path components while allowing programmable behavior through an I2C interface. The device provides three video channels, a selectable 2:1 multiplexer, selectable low-pass or bypass filter configurations, and programmable 0 dB gain. Its low-power design and single-supply operation suit portable equipment, including USB-powered systems, as well as HDTV, PVR, DVDR, projector, and general-purpose video equipment. An operating-temperature range of -40 °C to +85 °C supports industrial and commercial environments. The THS7353 is fabricated using Texas Instruments' complementary silicon-germanium BiCom-III process. This process supports the integration of three video channels, filtering functions, multiplexing, gain control, and digital control into a compact low-power device. The 20-TSSOP package supports surface-mount PCB assembly while providing separate routing flexibility for three video channels. Typical deployments include buffering component video and computer video outputs, switching between two video sources through the 2:1 multiplexer, filtering unwanted video-frequency content, and protecting source devices from downstream loading. Portable and projector designs benefit from the 2.7 V minimum supply and 16.2 mA quiescent current at 3.3 V, although system-level power depends on the selected configuration and output loading. Design the I2C address and control register settings before laying out the PCB, and confirm compatibility with the video timing and filter requirements of the target source. Decoupling and analog return paths should be arranged to minimize switching noise and ground potential differences between the amplifier and video source. This product page combines manufacturer specifications, application guidance, candidate replacement analysis, and practical PCB considerations. It identifies where THS7353PW fits, which published alternatives remain unverified as true pin-to-pin replacements, and which design parameters should be checked before approving a substitution.

RFQ پەیوەندی
THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments
THS7375

THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments

The THS7375 is a low-power, single-supply, 3 V to 5 V four-channel integrated video buffer from Texas Instruments, fabricated using the complementary Silicon-Germanium (SiGe) BiCom3X process. It is available in a lead-free and green (RoHS) compliant TSSOP-14 package. The device incorporates a sixth-order Butterworth filter that can be bypassed, making it useful as a digital-to-analog converter (DAC) reconstruction filter. With a rail-to-rail output stage and a fixed gain of 5.6 V/V (15 dB), the THS7375 is designed for SDTV video applications, providing excellent image quality and driving capability for both AC and DC coupled loads. A video amplifier is an electronic amplifier that processes video signals, typically providing gain, buffering, and filtering to ensure signal integrity over transmission lines. In the signal chain, the THS7375 sits between a video DAC or encoder and the output connector, performing reconstruction filtering and line driving. It belongs to the category of integrated video buffers, which are essential in consumer electronics, set-top boxes, DVD players, and video surveillance systems. The THS7375's integrated filters eliminate the need for external passive components, simplifying design and reducing board space. Key features include a 6th-order Butterworth filter with a cutoff frequency suitable for SDTV (standard-definition television) signals, a fixed gain of 5.6 V/V, and the ability to drive two lines per channel or 75-ohm loads. The device operates from a single 3 V to 5 V supply, making it compatible with common digital logic levels. The rail-to-rail output stage ensures maximum output swing, and the low power consumption makes it ideal for battery-powered or power-sensitive applications. Technically, the THS7375 uses the BiCom3X process, which combines bipolar and CMOS transistors on a silicon-germanium substrate, offering high-speed performance with low power. The integrated filter is a 6th-order Butterworth type, providing a flat passband and sharp roll-off to remove out-of-band noise and aliasing artifacts. The device also features an internal gain of 5.6 V/V, which is optimized for driving video loads with proper termination. Typical applications include video buffer and line driver for SDTV signals in set-top boxes, DVD players, video recorders, and surveillance systems. It is also suitable for driving video signals from DaVinci processors and other video encoders. The THS7375's ability to drive two lines per channel allows for flexible routing in complex video distribution systems. When designing with the THS7375, ensure proper power supply decoupling with a 0.1 uF ceramic capacitor close to the VCC pin. The input should be AC-coupled if the source has a DC offset, and the output should be terminated with 75-ohm resistors to match the characteristic impedance of the cable. The filter bypass pin can be used to disable the internal filter if external filtering is preferred.

RFQ پەیوەندی
THS7530PWP - 300 MHz Fully Differential VGA | Texas Instruments
THS7530PWP

THS7530PWP - 300 MHz Fully Differential VGA | Texas Instruments

The Texas Instruments THS7530PWP is a fully differential, continuously variable gain amplifier featuring a 300 MHz bandwidth, DC-coupled operation, and a 14-pin HTSSOP package with an exposed thermal pad. It accepts a single-ended or differential supply and combines high-impedance differential inputs, low-impedance differential outputs, voltage-controlled gain, output common-mode control, and output voltage clamping. A variable gain amplifier, or VGA, is an amplifier whose gain changes under electronic control. A VGA belongs to the broader family of amplifiers, which in turn forms part of the analog and mixed-signal semiconductor hierarchy. Unlike a fixed-gain amplifier, a VGA allows a receiver, imaging system, or instrumentation channel to vary signal amplitude without changing the surrounding circuit topology. The fully differential architecture preserves a balanced signal path and reduces sensitivity to common-mode disturbances. Key features include a 300 MHz small-signal bandwidth, voltage-controlled continuous gain adjustment, differential input and differential output operation, and separate control of output common mode. The device operates from a single 5.5 V supply or from split supplies of ±2.75 V. Its 14-pin HTSSOP package exposes a thermal pad for improved heat dissipation, and the specified operating temperature range is -40 °C to 85 °C. Internally, the THS7530 uses Texas Instruments' BiCom III silicon-germanium complementary bipolar process. That process supports the high-speed operation required by the device while preserving DC coupling and low-impedance differential outputs. The gain-control and common-mode inputs are high-bandwidth control paths, so their routing and impedance matter as much as the signal inputs when system settling time is important. Typical uses include ultrasound and medical imaging front ends, communications receivers, instrumentation amplifiers, oscilloscope and test-equipment input chains, and other wideband analog systems that require adjustable attenuation or gain. Differential signaling is particularly useful when the source produces a small differential voltage across a common-mode range that a single-ended amplifier would not accommodate cleanly. For PCB design, use the exposed thermal pad as a heat-spreading and low-inductance connection rather than leaving it electrically unconnected. Place input, output, gain-control, and common-mode routing away from high-current switching nodes. Terminate differential pairs symmetrically and follow the pin-description table in the manufacturer datasheet when assigning tracks and ground connections. This page combines the manufacturer device information, orderable-package details, practical PCB guidance, and a constrained drop-in comparison for engineers who need a 300 MHz fully differential VGA in the HTSSOP PWP footprint. Use the Request a Quote form on this page for current commercial availability, minimum order quantity, and lead-time confirmation.

RFQ پەیوەندی
TL072CDR - Dual Low-Noise JFET Op Amp | Texas Instruments
TL072CDR

TL072CDR - Dual Low-Noise JFET Op Amp | Texas Instruments

The Texas Instruments TL072CDR is a dual, low-noise JFET-input operational amplifier with two amplifiers in an 8-pin SOIC package. Verified distributor data identifies a 3 MHz gain-bandwidth product, 13 V/µs slew rate, and a 7 V to 36 V listed supply range. Its JFET input stage supports high input impedance and low input bias current, making the TL072CDR suitable for audio, instrumentation, filtering, and signal-conditioning circuits. The device also provides internal frequency compensation, output short-circuit protection, and latch-up-free operation. A JFET-input operational amplifier is an analog amplifier whose input stage uses junction field-effect transistors. Compared with a bipolar-input amplifier, the JFET stage generally provides lower input bias current and higher input resistance, while retaining useful low-noise performance. In system terms, the TL072 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Two amplifiers in one package reduce board area for stereo audio, balanced signal paths, active filters, and instrumentation signal chains. The verified product results specifically highlight low-noise JFET inputs, low total harmonic distortion, high input impedance, and high slew rate. These characteristics are useful in audio preamplifiers, microphone stages, sensor amplifiers, and active filters where the amplifier must preserve small signals without excessive input loading. The 3 MHz bandwidth supports applications up to moderate signal frequencies, while the 13 V/µs slew rate helps preserve large-signal waveform shape. Exact noise, offset, common-mode rejection, supply-current, and output-swing values were not supplied in the verified excerpts and are therefore marked for data completion rather than inferred. The TL072CDR is packaged in SOIC-8 and is ordered in a tape-and-reel commercial suffix arrangement identified by the exact MPN TL072CDR. Its two-amplifier architecture is useful when a design requires matched-channel placement or duplicate gain stages. Because it is not a rail-to-rail precision amplifier, the supply voltage and input/output signal limits must be checked against the manufacturer datasheet before use in modern low-voltage systems. Typical applications include stereo audio preamplification, microphone and instrument signal conditioning, active low-pass or band-pass filters, analog sensor interfaces, and general dual-amplifier utility circuits. Compared with a higher-performance precision audio amplifier, the TL072 offers a conventional general-purpose solution with JFET inputs and a familiar SOIC footprint. Its low-noise and high-slew-rate characteristics make it appropriate for cost-sensitive audio designs where the circuit does not require rail-to-rail operation or very low offset voltage. Designers should use the manufacturer datasheet for the complete electrical limits and pin configuration. Decoupling capacitors should be placed close to the supply pins, and the unused amplifier channel must be configured according to the datasheet rather than left floating. This page combines verified distributor specifications, source-linked product information, and practical design context for engineers evaluating the TL072CDR.

RFQ پەیوەندی
TL072CP - Dual JFET-Input Low-Noise Op Amp, 8-PDIP | Texas Instruments
TL072CP

TL072CP - Dual JFET-Input Low-Noise Op Amp, 8-PDIP | Texas Instruments

The Texas Instruments TL072CP is a dual JFET-input operational amplifier offering low noise (18 nV/√Hz typ at 1 kHz), high slew rate (13 V/µs typical), and wide bandwidth (3 MHz typical GBW) in an 8-pin PDIP through-hole package. The device contains two independent low-noise op amps using a JFET input stage that delivers high input impedance, low input bias current, and output short-circuit protection. It operates from ±3.5 V to ±18 V dual supplies, or equivalently 7 V to 36 V single-supply, with internal frequency compensation and latch-up-free operation. A JFET-input operational amplifier is a type of op amp whose input stage uses Junction Field-Effect Transistors instead of bipolar transistors, providing extremely high input impedance (typically 10^12 Ω) and very low input bias currents (typically 30 pA). Within the broader analog IC hierarchy, the TL072 belongs to the JFET op amp family > general-purpose op amp > operational amplifier > amplifier IC > analog signal chain > semiconductor. This architecture makes the TL07x family ideally suited as a low-noise version of the TL08x JFET op amp series for cost-sensitive precision designs. Key features include low total harmonic distortion (0.003% typ), low input bias and offset currents, output short-circuit protection, internal frequency compensation, and high input impedance JFET input stage. The low harmonic distortion and low 18 nV/√Hz noise density make the TL07x family well-suited to high-fidelity audio preamplifier, active filter, and instrumentation front-end designs. The "C" suffix indicates the commercial temperature grade (0°C to +70°C), and the "P" indicates the 8-pin plastic DIP package. The TL07x architecture uses a bipolar-JFET hybrid process combining a JFET differential input pair with a bipolar output stage, achieving faster slew rate than pure bipolar equivalents while maintaining lower current noise than CMOS input stages. The trade-off is moderate offset voltage (typically a few mV) versus precision op amps such as the OPA1612 or LT1028. Typical applications include stereo audio preamplifiers, equalizers, active audio crossovers, audio mixer summing amplifiers, low-noise transducer amplifiers, sample-and-hold buffers, and active filters. The TL072 is also widely used in hobbyist guitar effects pedals (e.g., Tube Screamer variants) and synthesizer modules. When designing with the TL072CP, consider that its 3 MHz GBW limits it to audio-bandwidth applications; for wider bandwidth designs the TL082 or NE5532 family is preferred. Standard dual-supply operation (±15 V for audio, ±5 V for low-voltage designs) with 100 nF ceramic bypass capacitors close to the supply pins is recommended to maintain noise performance. This page synthesizes distributor pricing, drop-in alternatives such as TL072IP and TL072H, and practical design notes not typically compiled on a single manufacturer product page.

RFQ پەیوەندی
TL074CDR - Quad Low-Noise JFET Op-Amp 14-SOIC | Texas Instruments
TL074CDR

TL074CDR - Quad Low-Noise JFET Op-Amp 14-SOIC | Texas Instruments

The Texas Instruments TL074CDR is a quad low-noise JFET-input general-purpose operational amplifier integrating four high-voltage JFET-input stages and bipolar transistors in a single 14-pin SOIC package. Each of the four channels delivers a typical gain bandwidth of 3 MHz, a slew rate of 13 V/us, and an equivalent input noise voltage of 18 nV/sqrt(Hz) at 1 kHz. The device operates from a single supply of 7 V minimum or dual supplies up to +/-18 V (absolute maximum 36 V), with output swing to within approximately 1.5 V of each rail on a +/-15 V supply. What is a JFET-input operational amplifier? A JFET-input op-amp (sometimes called a JFET op-amp or BiFET op-amp when JFET and bipolar are monolithically combined, as in the TL074) is a type of operational amplifier whose input stage uses JFET transistors instead of bipolar transistors. The JFET input delivers an extremely high input impedance (typically 10^12 ohm) and very low input bias current (typ. 30 pA), making the topology ideal for high-impedance sensor front-ends, audio preamplifiers, and integrator circuits. JFET-input op-amps sit within the operational amplifier taxonomy below general-purpose amplifiers and above specialty low-noise instrumentation amplifiers. Key features of the TL074CDR include internal frequency compensation, output short-circuit protection, latch-up-free operation, low total harmonic distortion, and a low offset-voltage temperature coefficient. The four independent channels share common power pins, eliminating the need for four separate single op-amps in dense multi-channel designs. The 'C' speed grade offers 3 MHz GBW and 13 V/us slew rate, while the 'B' grade and standard 'non-suffix' grade share the same channel architecture but vary in offset specifications. From a circuit-design standpoint, the TL074CDR is built on TI's mature BiFET-II process, which combines a JFET input differential pair with a bipolar output stage to deliver higher output drive (typ. 20 mA short-circuit output current) than all-JFET designs while preserving JFET-class input impedance. The internal compensation capacitor removes the need for external frequency-compensation components and guarantees unity-gain stability. Typical applications include audio preamplifiers and equalizers, active filters (Sallen-Key, multiple-feedback), signal conditioning for transducers, sample-and-hold buffers, professional audio mixers, and general-purpose signal-conditioning stages. The 14-SOIC package is pin-compatible with the legacy TL074 footprint and occupies roughly half the board area of a 14-DIP version while still supporting hand-soldering on standard 1.27 mm pitch land patterns. When designing with the TL074CDR, ensure that the input common-mode voltage stays within the specified input voltage range (VCC- + 4 V to VCC+ + 4 V on a single supply) and that the output stays below the absolute maximum supply rails. For ultra-low-noise instrumentation front-ends, consider the lower-noise OPA167x or OPA1612 family; for higher precision DC accuracy, consider the OPA2277.

RFQ پەیوەندی
TL082CDR - Dual 30V 3MHz JFET Op Amp | Texas Instruments
TL082CDR

TL082CDR - Dual 30V 3MHz JFET Op Amp | Texas Instruments

Texas Instruments TL082CDR is a dual JFET-input operational amplifier with a 30 V supply rating, 3 MHz gain-bandwidth product, and 13 V/us slew rate, supplied in an 8-pin SOIC package. Its two channels combine matched JFET and bipolar transistors in one monolithic IC, supporting general-purpose low-noise and high-input-impedance signal conditioning. A JFET-input operational amplifier is a voltage-amplifier device whose input stage limits input bias current while preserving low-noise behavior. In the broader semiconductor hierarchy, the TL082 belongs to the operational-amplifier class, then analog ICs, amplifiers, and signal-chain components. Its wide supply capability makes it suitable for industrial and instrumentation circuits operating from split or single positive rails up to the manufacturer's stated 30 V limit. The verified family description identifies the TL082 as a dual amplifier rated for 30 V operation with 3 MHz bandwidth and 13 V/us slew rate. These headline values provide enough bandwidth for audio, buffering, active filtering, sensor interfaces, and general feedback-control loops. Because the target is specified as TL082CDR, the package and order-code details should be confirmed against the Texas Instruments product page and manufacturer datasheet before production release. The device uses JFET-input transistors followed by bipolar signal-processing circuitry, providing high input resistance and relatively low input bias current. This input architecture is useful when driving high-impedance sources such as sensors, photodiodes, or measurement probes. The 3 MHz bandwidth also makes the amplifier suitable for small-signal stages rather than high-frequency, high-current, or power-amplifier applications. Typical uses include dual-channel audio preamplification, low-leakage sensor interfaces, active filters, sample-and-hold buffers, and dual feedback-control channels. Designers should pay attention to supply bypass, output-current limits, input common-mode range, output swing, stability with capacitive loads, and the exact pinout of the 8-SOIC package. Decoupling capacitors should be placed close to the supply pins to reduce parasitic inductance and preserve low-noise behavior. The principal design trade-off is flexibility versus precision: a general-purpose JFET input amplifier is easy to apply across many signals, but it may not match dedicated low-noise, low-offset, high-speed, or precision amplifier architectures. For replacement decisions, compare supply voltage, input bias current, offset voltage, bandwidth, slew rate, common-mode range, output swing, package pins, and required noise performance rather than relying only on the TL082 name. This page synthesizes the verified manufacturer description, distributor listings, package information, and practical selection considerations for engineers evaluating the TL082CDR. It also identifies which electrical and compliance values require confirmation from the manufacturer datasheet rather than inference.

RFQ پەیوەندی
TLC2264CPWR - Quad 16V 710kHz Rail-to-Rail Op Amp | Texas Instruments
TLC2264CPWR

TLC2264CPWR - Quad 16V 710kHz Rail-to-Rail Op Amp | Texas Instruments

The Texas Instruments TLC2264CPWR is a quad, 16-V, 710-kHz rail-to-rail operational amplifier in a 14-pin TSSOP (PW) package, fabricated in TI's Advanced LinCMOS process. Each of the four channels delivers a gain bandwidth product of 710 kHz and a slew rate of 0.55 V/us, while output swing reaches both supply rails. The device operates from a single supply of 2.2 V to 16 V or split supplies of plus/minus 2.2 V to plus/minus 8 V, supporting modern low-voltage analog designs. What is a rail-to-rail op amp? A rail-to-rail operational amplifier is a specialized analog IC whose output voltage swing can reach (or come close to) both the positive and negative supply rails, maximizing dynamic range in low-voltage single-supply systems. Rail-to-rail amplifiers sit within the larger hierarchy of operational amplifiers -> linear amplifiers -> analog ICs -> signal conditioning, and they are critical building blocks in sensor interfaces, ADC drivers, and battery-powered equipment where every millivolt of headroom matters. Key specifications include 12 nV/sqrt Hz typical input-referred voltage noise at 1 kHz, 1 pA typical input bias current, and 500 uA maximum quiescent current per channel. The TLC2264 also features a common-mode input voltage range that includes the negative rail, fully specified single-supply and split-supply operation, and ESD-protected inputs. The TSSOP-14 footprint keeps board area low while exposing a thermal pad for modest heat dissipation at elevated ambient conditions. Architecturally, the Advanced LinCMOS process yields low input bias currents suitable for high-impedance sensor front-ends and pico-amp-level signals. The output stage design allows the swing to reach within millivolts of each rail at moderate load, enabling 12-bit and 14-bit ADC input ranges to be fully utilized in 5V systems. Typical applications include transducer amplification in industrial process control, signal conditioning for portable and battery-powered instrumentation, low-side current sensing, rail-splitting in single-supply ADC front-ends, and active filtering. Its low noise and low bias current also suit ECG monitor front-ends and other medical instrumentation requiring high input impedance. When designing with this op amp, place the supply bypass capacitor (typically 0.1 uF ceramic in parallel with 10 uF bulk) within 5 mm of the VCC+ and VCC- pins. For unity-gain buffer configurations, the output can lightly oscillate due to capacitive loading - isolate the output with a 50-ohm series resistor if driving long PCB traces or cables. This page synthesizes authentic distributor pricing, drop-in same-package alternatives, and practical design notes - the kind of consolidated engineering reference not found in the manufacturer datasheet alone.

RFQ پەیوەندی
TLC272CD - Dual 16V 2MHz CMOS Op-Amp | Texas Instruments
TLC272CD

TLC272CD - Dual 16V 2MHz CMOS Op-Amp | Texas Instruments

The Texas Instruments TLC272CD is a precision dual operational amplifier built on TI silicon-gate LinCMOS technology, delivering 2 MHz gain-bandwidth and 16 V maximum single-supply operation in an 8-pin SOIC package. It combines two rail-friendly CMOS op-amp channels with high input impedance, low input bias current, and low noise, with input common-mode range extending to the negative rail (In to V-). An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, the foundational building block of the analog signal chain within the broader amplifier IC and power-management/signal-conditioning hierarchy. Single-supply CMOS op-amps such as the TLC272 family are optimized to operate directly from common logic and battery rails, where the input range must include ground (V-). Key features include a wide supply range over the specified temperature range (16 V single-supply operation), input offset voltage drift of typically 0.1 uV/month including the first 30 days, and very low input bias current due to the CMOS input stage, which yields very low noise current that is insignificant in most applications. The LinCMOS process provides excellent long-term offset stability without the input-current penalties of bipolar designs. Technically, the silicon-gate LinCMOS architecture keeps first-stage differential-pair current low; per the TLC27xx datasheet, noise performance in op-amp circuits depends strongly on this first-stage current, and the TLC272's low bias-current requirement results in minimal noise current. Speeds approach those of general-purpose BiFET amplifiers while retaining the input impedance advantages of CMOS. Typical applications include sensor signal conditioning and transducer interfaces (high-impedance inputs preserve signals from piezo and photodiode sources), active filters and integrators in battery-powered instrumentation, and general-purpose single-supply amplification in industrial and consumer control boards. Design consideration: as with any CMOS input, use appropriate input protection against electrostatic discharge and avoid letting inputs exceed the supply rails; the 2 MHz bandwidth means closed-loop gains above about 20 with adequate phase margin for stable, low-gain-error operation. This page synthesizes distributor availability data, verified drop-in alternatives within the TLC27xx family, and practical design notes beyond the headline specifications found in the manufacturer datasheet.

RFQ پەیوەندی
TLC272CDR - Dual 16V CMOS Op-Amp 2MHz SOIC-8 | Texas Instruments
TLC272CDR

TLC272CDR - Dual 16V CMOS Op-Amp 2MHz SOIC-8 | Texas Instruments

The Texas Instruments TLC272CDR is a precision dual operational amplifier fabricated on TI silicon-gate LinCMOS technology, offering 2 MHz (typ 2.2 MHz) bandwidth, 3.6 V/us slew rate, and single-supply operation from 3 V to 16 V in an 8-pin SOIC package. An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs, forming the foundational building block of the analog signal chain within the broader hierarchy of amplifier ICs, linear ICs, and semiconductors. Rail-to-rail style input flexibility on single-supply parts like the TLC272 lets designers amplify sensor signals that swing near ground without a negative supply, dramatically simplifying battery-powered and industrial designs. Key features include a maximum input offset voltage of 500 uV at 25 C with VDD = 5 V, extremely low offset drift of typically 0.1 uV/month (including the first 30 days), very high input impedance with low bias currents inherent to CMOS inputs, and a common-mode input range that extends to the negative rail (In to V-). These characteristics make it a cost-effective alternative to BiFET general-purpose amplifiers. The LinCMOS process provides input bias currents in the picoampere range, enabling direct interfacing with high-impedance sources such as pH probes, photodiodes, and piezoelectric sensors without external buffering. The dual amplifier in one SOIC-8 saves board area and improves channel matching in filter and instrumentation circuits. Typical applications include sensor signal conditioning, active filters, battery-powered portable instrumentation, and low-frequency data-acquisition front ends where single-supply, low-bias-current operation is required. Design consideration: keep source impedances moderate and use adequate supply bypassing; the CMOS input is sensitive to static, so observe ESD handling precautions. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
TLE2022IDR - Dual Precision Low-Power Op Amp | Texas Instruments
TLE2022IDR

TLE2022IDR - Dual Precision Low-Power Op Amp | Texas Instruments

The Texas Instruments TLE2022IDR is a dual precision, high-speed, low-power operational amplifier built on TI's Excalibur bipolar process, housed in an 8-pin SOIC (D) package and rated for the industrial -40C to +85C temperature range. It delivers 2 circuit channels with low offset voltage, high unity-gain bandwidth, and low power consumption typical of the Excalibur family, making it suitable for general-purpose precision signal conditioning from a single supply. The part is specified as a standard (general-purpose) amplifier in TI's amplifier portfolio. What is an operational amplifier (op amp)? An op amp is a high-gain DC-coupled electronic voltage amplifier with differential inputs and, typically, a single-ended output. It is one of the most ubiquitous building blocks in analog electronics, sitting below instrumentation amplifiers and active filters in the signal-chain hierarchy and above individual transistors in functional abstraction. Precision low-power single-supply op amps such as the TLE2022 family are optimized for systems that must operate from a single positive rail (often 3.3V or 5V) while still delivering DC accuracy and AC bandwidth close to what dual-supply parts achieve. Key features of the TLE2022IDR include two independent op-amp channels in a single SOIC-8 footprint, low power consumption characteristic of the Excalibur process, high-speed response relative to competing low-power op amps, unity-gain stability, and support for single-supply operation. The complementary bipolar process uses isolated vertical PNP transistors that improve input common-mode range and slew rate versus older designs, which is one reason the TLE2022 family remains popular as a successor to the OP21 in legacy designs. Typical applications include active filters, precision integrators, sample-and-hold front ends, transducer signal conditioning, and battery-powered instrumentation. The 8-pin SOIC footprint is industry standard, allowing easy hand prototyping and high-density SMT assembly on the same PCB land pattern used by countless alternative dual op amps. When designing with this device, observe the datasheet maximum supply rating and provide proper input common-mode biasing when used on a single supply; the lower rail of the input common-mode range may not extend all the way to ground. Decouple the supply pin close to the IC with at least 0.1 uF ceramic capacitance. A unity-gain stable part can be operated without compensation but should be kept clear of capacitive loads exceeding the datasheet's drive specification. This page synthesizes current distributor pricing, drop-in same-package and cross-brand alternatives from verified cross-reference data, and practical design notes not found in the bare manufacturer datasheet - giving an engineer a single, structured view for sourcing and second-sourcing decisions.

RFQ پەیوەندی
TLP7820(A-LF4 - 5 kVrms Isolated Amplifier | Toshiba
TLP7820(A-LF4

TLP7820(A-LF4 - 5 kVrms Isolated Amplifier | Toshiba

The Toshiba TLP7820(A-LF4 is a one-channel optically isolated amplifier with analog output, 5000 Vrms isolation, and a SO8L (LF4) package. It operates from 3 V to 5.5 V, supports differential input sensing, and is designed for high-precision current sensing in electronic motor drives. The isolation barrier transfers a measured voltage signal optically while electrically separating the sensed power circuit from downstream control electronics. An isolation amplifier is an analog signal-conditioning IC that combines input amplification, modulation across a galvanic isolation barrier, and signal reconstruction at the output. Unlike a conventional voltage amplifier, its primary purpose is to measure a differential signal while maintaining high-voltage isolation. This places it in the isolated-sensing branch of the industrial, power-conversion, and motor-control semiconductor hierarchy. Key verified characteristics include a 3 V to 5.5 V supply range, differential sensing, 5000 Vrms isolation, and analog output. Toshiba identifies motor phase current sensing and inverter current or voltage sensing as primary use cases. In a typical motor-drive circuit, motor current flows through an external shunt resistor and the resulting differential voltage is measured by the amplifier. The device architecture provides an analog output while preserving a reinforced-style isolation barrier up to the verified 5000 Vrms rating. Its single-channel SO8L package supports compact isolated signal-conditioning layouts, but the exact pin assignments, input range, bandwidth value, propagation behavior, accuracy limits, and temperature limits must be taken from the manufacturer datasheet. Typical applications include three-phase inverter phase-current measurement, DC motor control, industrial inverter monitoring, power-supply current feedback, and isolated analog voltage sensing. The differential architecture suits shunt-based measurements where common-mode voltage is elevated or varies with the switching environment. PCB design should preserve creepage and clearance around the isolation barrier, keep input and output grounds separate, and place the shunt path and amplifier inputs according to the manufacturer layout guidance. Filtering near the sensor input may be needed if switch-node transients exceed the device limits; component values should not be inferred without the complete datasheet specifications. This page consolidates the verified manufacturer and distributor information, separates confirmed TLP7820 characteristics from unavailable parameters, and provides engineering-oriented application and sourcing context rather than treating packaging-code variants as engineering alternatives.

RFQ پەیوەندی
TLP7820(A-TP4 - 5kVrms Isolated Amplifier | Toshiba
TLP7820(A-TP4

TLP7820(A-TP4 - 5kVrms Isolated Amplifier | Toshiba

The Toshiba TLP7820(A-TP4 is a photocoupler-based isolation amplifier with analog output, 5000 Vrms reinforced isolation, and an 8-pin SO8L package. It is designed primarily for motor phase-current and inverter voltage sensing. The verified source data identifies one differential isolation-amplifier circuit and an 8-SO package, while detailed electrical characteristics are not provided in the supplied records. An isolation amplifier is an analog signal-conditioning IC that transfers voltage information across a galvanically isolated barrier while electrically separating high-voltage circuitry from the low-voltage control domain. In the application hierarchy, the TLP7820 belongs to isolation amplifiers, optically isolated amplifiers, signal-conditioning ICs, analog ICs, and semiconductor devices. Its isolation barrier helps prevent ground faults and high common-mode potentials from reaching measurement, protection, or control electronics. Toshiba identifies the TLP7820 as an analog-output isolation amplifier rated to 5000 Vrms. The official product description specifically targets current sensing in electronic motor drives, where an external resistor produces a voltage proportional to motor current. The TLP7820 senses that voltage across its isolated input side and presents the result on the non-isolated output side. The provided records also associate the device with power-inverter current sensing. The isolation mechanism is optical within a photocoupler-type package. Optical isolation breaks the direct conductive path between input and output while preserving the intended analog signal relationship. In practical systems, the amplifier is paired with a precision shunt resistor, power-supply bypassing, an analog acquisition stage, and a controller such as a motor-drive MCU. Exact gain, bandwidth, input range, common-mode limits, supply requirements, and accuracy must be confirmed in the manufacturer datasheet before release to production. Typical uses include three-phase motor-drive shunt sensing, inverter leg-current measurement, power-converter feedback, and isolated analog-voltage sensing across a high-voltage barrier. Unlike ordinary operational amplifiers placed directly beside a shunt, the TLP7820 provides a defined isolation function suited to systems where the sensed node can sit at a hazardous or elevated potential. PCB design should preserve the isolation barrier by maintaining the package creepage and clearance required by the working voltage and applicable safety requirements. Place input-side and output-side ground returns independently, route copper so isolation barriers cannot be bridged by solder, test pads, or silkscreen-dependent features, and use stable references and supply decoupling appropriate for the measurement accuracy required. This page consolidates the verified Toshiba product-page data, distributor identification, sourcing links, and engineering cautions that are not presented together in the manufacturer overview. Because the supplied web records do not expose a complete parametric datasheet, unsupported values are intentionally marked for verification rather than inferred from generic isolation-amplifier specifications.

RFQ پەیوەندی
TLP7820(B-LF4 - 5V 5kVrms Isolation Amplifier | Toshiba
TLP7820(B-LF4

TLP7820(B-LF4 - 5V 5kVrms Isolation Amplifier | Toshiba

The Toshiba TLP7820(B-LF4 is a 5 V optically isolated analog-output amplifier with 5000 Vrms reinforced isolation, one isolation channel, and an 8-pin SO8L (LF4) package. It is designed for motor phase-current and inverter voltage sensing, where an external shunt produces a small differential voltage that must be transferred safely across a high-potential barrier. The verified product information identifies an analog output, differential input operation, 3 V to 5.5 V supply range, and a surface-mount SO8L package. An isolation amplifier is an analog signal-conditioning IC that transfers a low-voltage input across an electrical isolation barrier while electrically separating the input and output grounds. Optically isolated amplifiers use an internal light path or other isolation mechanism to prevent high-voltage ground currents and common-mode transients from reaching the measurement system. This product belongs to the isolation-amplifier family of signal-chain ICs rather than a general-purpose operational amplifier. The TLP7820 is intended for current sensing in electronic motor drives. In a typical implementation, motor current flows through an external resistor and the resulting analog voltage drop is sensed by the isolation amplifier. Its differential input arrangement helps reject common-mode voltage at the shunt, while the 5000 Vrms isolation rating supports high-side sensing in inverter and motor-control systems. The analog output can be connected to a controller or monitoring ADC after the system designer confirms the required transfer gain, bandwidth, accuracy, and supply conditions. The verified Toshiba material also references EN IEC 60747-5-5 option (D4) documentation, which is relevant when evaluating isolation-related product qualification requirements. The part is associated with motor phase-current sensing, inverter current sensing, and inverter voltage sensing. The available LCSC listing reports a 5-piece stock example and a starting price of $11.3258, but pricing and inventory are market-dependent and were not provided as a structured XAIPART price schedule. A practical design must preserve the isolation barrier rather than treating SO8L as an ordinary op-amp package. Keep high-voltage and low-voltage copper regions separated, route the shunt signal as a short differential pair, provide local supply bypassing where the datasheet specifies it, and verify creepage, clearance, capacitor insulation, and system-level withstand requirements. The TLP7820(B-LF4 is best considered for isolated measurement in power-conversion equipment after checking the exact option suffix and datasheet revision. This page consolidates manufacturer product information, distributor findings, and cross-reference evidence into an engineering-oriented overview. It distinguishes verified information from fields that still require the latest Toshiba datasheet or authorized distributor quote, helping designers evaluate the TLP7820 without substituting unverified ratings or assuming that a similar package implies drop-in compatibility.

RFQ پەیوەندی
TLP7820(B-TP4 - 5kVrms Isolation Amplifier | Toshiba
TLP7820(B-TP4

TLP7820(B-TP4 - 5kVrms Isolation Amplifier | Toshiba

Toshiba TLP7820(B-TP4 is a precision isolation amplifier intended for current sensing in electronic motor drives, packaged as an 8-pin SO8L device. Verified source information identifies the device as a photocoupler-type isolation amplifier with an analog output, 5,000 Vrms isolation rating, and SO8L (LF4) package construction. An isolation amplifier is an optically isolated signal-conditioning IC that transfers a voltage or current-related measurement across an electrical barrier while electrically separating high-power circuitry from the measurement domain. Its internal isolation barrier helps protect low-voltage control and sensing electronics from high common-mode voltages. The TLP7820 family is associated with motor phase-current, inverter-current, and voltage-sensing applications. The verified Toshiba product listing identifies TLP7820(B-TP4 as an isolation amplifier with an analog output and 5,000 Vrms isolation capability. The family is packaged in SO8L (LF4), while distributor and comparison listings describe an 8-pin SO/SOIC-style package. The device is therefore positioned for isolated current-measurement circuits rather than ordinary non-isolated operational-amplifier applications. Because the supplied sources do not provide the complete electrical characteristic table, input common-mode range, gain error, bandwidth, propagation delay, supply-current limits, or exact pin names, those values must be confirmed in the manufacturer datasheet before layout or qualification. This page does not infer unverified numerical specifications. The available evidence supports the device category, isolation rating, analog-output architecture, package family, and target sensing applications. Typical implementation places the TLP7820 across a current-sense shunt or inverter phase-current sensing path. Its isolation barrier allows measurement information to cross from the power stage toward a controller while maintaining galvanic separation. Designers should verify the complete recommended shunt, input filter, supply, output, and grounding configuration in the Toshiba datasheet and evaluate the external resistor network for the intended current range. Design emphasis belongs on barrier isolation, common-mode voltage limits, input-referenced filtering, output scaling, and PCB creepage. The SO8L package should be placed with adequate isolation clearance and a defined high-voltage barrier; copper, slots, and grounded structures must not unintentionally reduce the rated isolation distance. The manufacturer datasheet is the controlling source for layout dimensions and safety requirements. This page consolidates verified manufacturer and distributor information, distinguishes documented facts from missing parameters, and provides application and sourcing guidance. It is intended to help engineers identify the correct isolation-amplifier family and obtain the authoritative Toshiba datasheet before committing to a PCB design.

RFQ پەیوەندی
TLP7820(D4-LF4 - 5kVrms Isolated Amplifier | Toshiba
TLP7820(D4-LF4

TLP7820(D4-LF4 - 5kVrms Isolated Amplifier | Toshiba

Toshiba TLP7820(D4-LF4 is an optically isolated, isolated sigma-delta modulator amplifier with analog output, 5000 Vrms isolation, a 3 V to 5.5 V supply range, and an SO8L (LF4) package. It is designed for motor phase current sensing, inverter current and voltage sensing, and other industrial power-monitoring systems requiring reinforced isolation between high-voltage signal paths and control electronics. An isolation amplifier is a signal-conditioning IC that transfers information across an electrically isolated barrier while preventing galvanic current flow between its input and output domains. The TLP7820 belongs to the isolated delta-sigma modulator class, combining an analog signal interface, optical isolation, and digital filtering into a device intended to simplify current-sense measurement systems. Its isolation amplifier hierarchy is isolation amplifier to optically isolated amplifier to signal-chain IC and industrial power-management component. Key verified features include 5000 Vrms isolation, operation from 3 V to 5.5 V, differential analog output, one isolation channel, and an SO8L (LF4) package. The D4 option is associated with EN IEC 60747-5-5 qualification according to the manufacturer document index supplied with the product data. These characteristics make the device applicable where a high-side shunt voltage must be measured without connecting the measurement ground to the inverter or motor power stage. The TLP7820 uses optical isolation to establish a safety barrier between the sensed voltage and the system-side output. Toshiba identifies the TLP7820 family as an isolation amplifier and isolated delta-sigma modulator product with analog output. Its differential output supports direct connection to measurement circuitry when implemented according to the manufacturer application guidance, while the isolated structure helps suppress common-mode effects associated with high-power switching environments. Typical applications include three-phase inverter motor control, motor phase-current measurement, industrial power conversion, power-supply monitoring, and isolated voltage sensing. These systems benefit from the 5000 Vrms isolation barrier when the measured shunt sits at a high common-mode voltage or when safety isolation is required between power electronics and supervisory control circuitry. Designers should preserve the isolation barrier, use the specified input and output components from the manufacturer datasheet, and provide adequate clearance and creepage around the package. Input filtering, output differential routing, grounding, and PCB contamination control are as important as electrical pin compatibility because they determine measurement accuracy and real-world isolation performance. This page consolidates verified manufacturer and distributor information for the TLP7820(D4-LF4, including supply range, isolation rating, package information, sourcing data, and documented same-brand alternatives. It also provides application guidance, comparison tables, and design notes intended to help engineers evaluate the device beyond basic distributor specifications.

RFQ پەیوەندی
TLP7820(D4-TP4 - 5kVrms Isolation Amplifier | Toshiba
TLP7820(D4-TP4

TLP7820(D4-TP4 - 5kVrms Isolation Amplifier | Toshiba

The Toshiba TLP7820(D4-TP4 is a single-channel optically isolated amplifier with analog output, 5,000 Vrms isolation voltage, and 230 kHz bandwidth in an 8-pin SO8L (LF4) surface-mount package. Designed for current sensing in electronic motor drives, it accepts a voltage derived from motor current flowing through an external shunt resistor and provides an isolated analog representation of that measurement. An optically isolated amplifier belongs to the isolation-amplifier category within analog signal-conditioning ICs. Its role in the broader hierarchy is isolation amplifier → optically isolated amplifier → analog signal-conditioning IC → semiconductor. Optical isolation separates the input measurement domain from the output and system ground, helping reduce common-mode voltage effects and ground-loop hazards when measurements are taken at a high-side shunt or inside a power-conversion stage. The principal verified features include one isolation channel, analog amplifier output, 5,000 Vrms isolation voltage, 230 kHz bandwidth, a 5 V supply indication, and an SO8L (LF4) package. The 230 kHz bandwidth provides useful signal bandwidth for motor phase-current measurement, while the 5,000 Vrms isolation rating supports applications requiring reinforced separation between the sensed circuit and downstream control electronics. The manufacturer describes the TLP7820 as an isolation amplifier for electronic motor drives. In a typical implementation, motor current passes through an external resistor, the resulting analog voltage drop is sensed by the isolated input side, and the output side delivers an amplified analog signal for measurement, control, or protection. The external shunt and input-network design remain important because they determine the measurable current range, sensitivity, and practical power dissipation. Typical uses include three-phase inverter phase-current sensing, motor-drive current feedback, power-converter monitoring, and isolated voltage sensing where a grounded controller must interface with a high-side or floating power stage. The same isolation-amplifier architecture can also support industrial current-measurement systems when its specified bandwidth, supply requirements, and isolation rating satisfy the application. When designing around the TLP7820(D4-TP4, preserve the isolation barrier and follow the manufacturer’s input and output application circuits. Shunt resistance, input common-mode range, gain, supply decoupling, and PCB creepage must be checked against the actual motor-drive topology; the available verified data does not provide those detailed limits.

RFQ پەیوەندی
TLP7820(D4ALF4 - 5000 Vrms Isolated Amplifier | Toshiba
TLP7820(D4ALF4

TLP7820(D4ALF4 - 5000 Vrms Isolated Amplifier | Toshiba

The Toshiba TLP7820(D4ALF4 is a single-channel optically isolated amplifier designed for accurate DC current measurement in electronic motor drives, inverter systems, and industrial power-conversion equipment. It provides analog output in an 8-pin SO8L package and is specified for 5000 Vrms isolation, 5 V operation, and 230 kHz bandwidth according to the manufacturer product and comparison data. An isolation amplifier is a precision signal-conditioning IC that transfers a low-voltage measurement signal across a galvanic isolation barrier while electrically separating the high-voltage and low-voltage domains. The TLP7820 uses optical isolation rather than a conductive connection between its two sides, helping reduce common-mode interference and protect low-voltage control electronics from high-side motor or inverter voltages. Key features include one analog isolation channel, 5000 Vrms isolation, analog output, 5 V supply operation, and 230 kHz bandwidth. The SO8L (LF4) package supports compact isolated-sensing designs, while the optical isolation structure is intended for motor phase current and voltage sensing. The manufacturer describes the device as a high-speed isolation amplifier for efficient isolation amplification. Toshiba positions the TLP7820 for electronic motor drives where an external shunt resistor converts phase current into a differential voltage that can be measured safely on the high-voltage side. The isolation amplifier then conveys that measurement to a controller or monitoring system across the isolation barrier. Its 230 kHz bandwidth supports current-loop and power-stage monitoring applications where the measured signal must follow dynamic phase-current changes. The 5000 Vrms isolation rating is the central system-level specification. It helps engineers create a safety separation between power-conversion circuitry and low-voltage control logic, subject to the complete application’s creepage, clearance, insulation, and safety requirements. The operating voltage and electrical limits must be confirmed from the manufacturer datasheet before final design release. Designers should pay particular attention to input common-mode range, output offset, gain, supply sequencing, shunt-resistor selection, and the analog isolation characteristics of the exact ordering code. The SO8L footprint should be checked against the PCB land pattern and creepage requirements before layout. This page consolidates manufacturer information, distributor availability, verified comparisons, and practical application guidance for engineers evaluating the TLP7820(D4ALF4. The TLP7820 family is listed for RoHS-compliant surface-mount applications and is available through major distributors such as DigiKey, Mouser, Arrow, LCSC, and Octopart. Verify current lifecycle status, pricing, stock, and lead time directly with the selected authorized distributor.

RFQ پەیوەندی