Amplifier ICs
بەرهەمەکان (3,200+)
TLV272CD - Dual 3MHz 16V Rail-to-Rail Op Amp | Texas Instruments
The Texas Instruments TLV272CD is a dual, general-purpose operational amplifier with a 16 V maximum supply, 3 MHz gain-bandwidth product, 2.4 V/us slew rate, and rail-to-rail output in an 8-SOIC package. Each channel is designed for low-power signal conditioning while maintaining useful bandwidth for general-purpose analog systems. An operational amplifier is a high-gain analog building block used to amplify, buffer, compare, or integrate signals. The TLV272 belongs to the voltage-feedback operational-amplifier hierarchy and combines a wide supply range, low channel current, and rail-to-rail output capability. Rail-to-rail output allows the output to approach the positive or negative supply limit more closely than a conventional output stage, improving dynamic range in low-voltage systems. Verified device characteristics include 550 uA per channel, 3 MHz bandwidth, 2.4 V/us slew rate, 2.7 V to 16 V operating supply range, 39 nV/Hz input-noise density, and input bias current specified as low as 1 pA. The family is positioned for portable instrumentation, sensor interfaces, audio paths, and general signal conditioning where dual-channel operation reduces package count. The wide supply range supports both conventional 5 V analog systems and higher-voltage rails, while the 3 MHz bandwidth supports signals beyond audio-band precision-only applications. The 2.4 V/us slew rate helps preserve large-signal response, although the exact output amplitude, load, and frequency must be checked against the manufacturer datasheet before final sizing. Typical uses include low-power sensor interfaces, buffered analog measurements, audio voltage buffers, active filtering, and general dual-channel conditioning. The SOIC-8 package is suitable for conventional surface-mount PCB assembly, but pin numbering and electrical limits must be verified against the exact TLV272 datasheet. A key design consideration is that low power and moderate bandwidth do not eliminate the need for stable reference and feedback networks. Place bypass capacitors near the supply pins, use short feedback paths, and verify common-mode, output-swing, noise, and stability requirements against the application. This page consolidates verified manufacturer and distributor information with design-oriented guidance; unsupported details remain explicitly marked for review.
TLV272ID - Dual 16V 3MHz R-R Op Amp | Texas Instruments
The Texas Instruments TLV272ID is a dual, 16 V, 3 MHz rail-to-rail output operational amplifier packaged in an 8-pin SOIC. It uses approximately 550 uA per channel and is specified for operation from 2.7 V to 16 V over a -40 C to +125 C temperature range. These headline values position it as a compact, low-power amplifier for general-purpose analog signal conditioning. An operational amplifier is an active analog component that amplifies the voltage difference between its differential inputs while using negative feedback to set closed-loop gain, filtering, or integration behavior. Within the hierarchy of integrated circuits, the TLV272 belongs to the operational-amplifier class, then to voltage-feedback amplifiers, analog ICs, and ultimately semiconductor signal-conditioning devices. Rail-to-rail output allows the output voltage to approach the supply limits at its rated operating conditions. Key verified characteristics include a 3 MHz gain-bandwidth product, dual-amplifier configuration, 550 uA supply current per channel, 16 V maximum supply rating, and rail-to-rail output operation. The 3 MHz bandwidth supports higher-frequency signal paths than very-low-bandwidth micropower amplifiers, while the 550 uA per-channel current supports battery-conscious designs. The -40 C to +125 C grade is suitable for industrial temperature requirements when the complete circuit is qualified for those conditions. The TLV272ID combines two independent amplifiers in one SOIC-8, reducing board area compared with two separate single-channel packages. Its operating characteristics are relevant for sensor interfaces, audio paths, filtering, and general voltage amplification. However, the provided web data does not specify input offset voltage, input bias current, noise density, output-current capability, or input common-mode range, so these values must be confirmed in the manufacturer datasheet before precision design. Typical uses include low-frequency audio amplification, buffered sensor outputs, active filters, and portable measurement circuits. When operating from a 2.7 V supply, engineers must confirm that output swing, input range, and load requirements remain acceptable at the selected signal amplitudes. The 16 V maximum rating does not by itself establish safe operation at every intermediate rail or temperature combination. The main PCB consideration is decoupling. Place input and output-conditioning components close to their associated pins, route feedback loops compactly, and provide stable supply bypassing. Stable operation also depends on the required common-mode and output ranges, load impedance, feedback topology, and output-current demand. This page combines verified manufacturer and distributor information with explicit data gaps, practical application guidance, and conservative sourcing. It is intended to speed engineering evaluation while avoiding unsupported claims about parameters not present in the retrieved records.
TLV272IP - Dual 16V 3MHz R-R Op Amp | Texas Instruments
The Texas Instruments TLV272IP is a dual, 16 V, 3 MHz operational amplifier with rail-to-rail output swing, supplied in an 8-pin PDIP package. It provides two amplifier channels, a 2.4 V/us slew rate, 550 uA/channel supply current and a 2.7 V to 16 V total supply range. The device is intended for low-power, wide-bandwidth signal conditioning where rail-to-rail output capability improves usable output range. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify voltage signals. The TLV272IP belongs to the operational-amplifier hierarchy and is appropriate for sensor interfaces, buffer stages, filters, audio paths and general-purpose analog signal chains. Its rail-to-rail output is useful when the amplifier must approach the positive or negative supply rail while retaining a defined output voltage. The main performance features are 3 MHz gain-bandwidth product, 2.4 V/us slew rate, 550 uA/channel supply current and 39 nV/Hz input noise voltage. The verified family information also specifies operation from 2.7 V to 16 V, with commercial and extended-temperature options in the broader TLV27x family. Because the TLV272IP is a dual device, one package can support two independent analog channels. The PDIP package is through-hole and therefore useful for prototypes, educational designs, repair assemblies and applications where leaded parts are preferred over surface-mount packages. Its 8-pin arrangement matches the dual-op-amp pinout convention, but the exact pin names and electrical limits must be confirmed against the manufacturer datasheet before final PCB release. The verified sources identify the TLV272IP as a dual rail-to-rail-output operational amplifier in an 8-PDIP package. Typical uses include low-voltage sensor buffering, portable instrumentation, audio preamplification, active filtering and industrial control signal conditioning. The 3 MHz bandwidth provides more signal bandwidth than a strictly low-frequency precision amplifier, while the 550 uA/channel current supports battery-conscious designs. The tradeoff is that the PDIP footprint is larger and less compact than an equivalent surface-mount package. For PCB design, place input and output components close to the relevant pins and maintain a common ground reference. Decoupling capacitors should be placed at the power pins to control supply impedance and high-frequency noise. Confirm stability, input common-mode range, output-load limits and supply current in the final circuit rather than relying only on the headline bandwidth and slew-rate figures. This product record combines verified manufacturer and distributor information with explicitly marked data gaps, practical application guidance and sourcing-oriented search terms. It is intended to help engineers identify the correct package, assess whether TLV272IP fits a signal-chain requirement and locate the manufacturer datasheet before committing to a design.
TLV274CD - 3 MHz Quad 16 V Operational Amplifier | TI
The Texas Instruments TLV274CD is a quad, 16 V, 3 MHz operational amplifier with rail-to-rail output capability, housed in a 14-pin SOIC package. The verified product data identifies a 550 µA-per-channel supply current, 2.4 V/µs slew rate, 2.7 V to 16 V supply operation, and a commercial temperature range identified by the CD ordering code. It is designed for general-purpose analog signal conditioning where low power, moderate bandwidth, and rail-to-rail output are useful. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify voltage differences between its input terminals. The TLV274 belongs to the operational-amplifier, analog-amplifier, and signal-conditioning IC hierarchy. Its four amplifiers in one package make it suitable for multi-channel systems, while rail-to-rail output helps the output approach the supply rails and improves dynamic range in low-voltage designs. The verified data lists 3 MHz bandwidth, 2.4 V/µs slew rate, 16 V maximum supply voltage, 550 µA per channel, and 550 µA/channel input-noise-related information. The wide supply range supports portable, industrial, test, and measurement systems. The low power per channel is useful when four amplifiers must operate continuously, while the 3 MHz bandwidth is more appropriate for general-purpose signal paths than precision low-frequency instrumentation alone. The TLV274CD uses a 14-pin SOIC package and is offered through distributors including DigiKey, Mouser, LCSC, and Octopart. The verified DigiKey result identifies it as a standard general-purpose amplifier with four circuits and rail-to-rail output. Because the available data does not provide complete pin names, exact electrical limits, or validated drop-in alternatives, those details are marked as needed rather than guessed. Typical uses include low-frequency sensor interfaces, buffered analog measurement chains, current or voltage signal conditioning, audio preamplifier stages, and general embedded control systems. Keep the input common-mode range, output swing, load, supply voltage, and stability requirements within the manufacturer datasheet limits, and account for input bias current, noise, and capacitive loading. For PCB design, place the bypass capacitor close to the supply pins and keep analog input and output routing short. Avoid excessive capacitive loading at the output and verify stability with the selected feedback network. This page combines verified manufacturer and distributor information with practical design guidance; confirm final electrical and mechanical details against the official TI datasheet before release.
TLV274ID - Quad 16V 3MHz RRO Op Amp | Texas Instruments
The Texas Instruments TLV274ID is a quad, general-purpose operational amplifier with 16 V supply capability, 3 MHz gain-bandwidth product, and rail-to-rail output operation in a 14-SOIC package. Each of its four channels draws 550 uA nominal supply current and supports a 2.4 V to 16 V supply range, making the device suitable for compact, low-power analog signal chains. An operational amplifier is an active analog component that uses high open-loop gain to amplify the difference between two input voltages. The TLV274 belongs to the operational-amplifier hierarchy and combines rail-to-rail output swing with a relatively high 3 MHz bandwidth. That balance is useful for signal conditioning, filtering, buffering, and general instrumentation where low supply current and usable high-frequency response matter. Key characteristics include four independent amplifiers in one package, rail-to-rail output, 3 MHz bandwidth, 2.4 V/us slew rate, and 550 uA/channel supply current. The reported input-voltage noise density is 39 nV/sqrt(Hz), while input bias current reaches as low as 1 pA in the characterized operating range. These values support low-level signal work, although input offset voltage, input common-mode range, and output-current limits were not supplied in the verified data. The TLV274ID is based on a rail-to-rail-output amplifier architecture rather than a rail-to-rail-input design. Designers must therefore verify that input signals remain inside the allowed common-mode region. Its 3 MHz bandwidth enables moderate-frequency feedback networks and sensing loops, but stability should be checked against output loading, capacitance, noise gain, and filter topology. Typical uses include low-power sensor conditioning, audio and communication interfaces, current measurement, data acquisition, filtering, and embedded analog control. Placing four amplifiers in one SOIC can reduce package count, but adjacent channels may share supply and thermal conditions. Decoupling and grounding therefore remain important when driving successive signals. Begin each supply rail with suitable local bypass capacitance and route high-current return paths away from sensitive analog inputs. Because the exact compensation recommendations and electrical limits are unavailable in the supplied source set, use the manufacturer datasheet for final gain, load, stability, and layout validation. This page combines verified product facts, application guidance, procurement context, and a conservative comparison of documented family variants. Its added value is an engineering-focused explanation of where the TLV274ID fits without treating unavailable electrical limits as assumptions.
TLV274IN - 3MHz Quad Rail-to-Rail Op Amp | Texas Instruments
The Texas Instruments TLV274IN is a four-circuit, general-purpose operational amplifier with a 3 MHz gain-bandwidth product, 2.4 V to 16 V supply-voltage range, and rail-to-rail output operation. It is packaged in a 14-pin PDIP and is intended for low-power signal conditioning across industrial, instrumentation, and embedded systems. The verified source data identifies 550 µA of supply current per channel, 2.4 V/µs slew rate, 39 nV/Hz input-noise voltage density, and specified operation from 0°C to 70°C. An operational amplifier is an analog building block that uses high open-loop gain to amplify the difference between two input voltages. Within the signal-chain hierarchy, the TLV274IN belongs to the operational-amplifier, analog-amplifier, and semiconductor categories. Rail-to-rail output capability allows the output to approach the positive or negative supply rail under suitable load conditions, while the wide supply range supports single-supply and dual-supply systems. Key features include four amplifiers in one package, a 3 MHz bandwidth, 2.4 V/µs slew rate, 550 µA per-channel supply current, 39 nV/Hz input-voltage-noise density, and 1 pA input-bias current over the specified temperature range. The low-power bias current is useful when preserving sensor signals and reducing loading, while the 3 MHz bandwidth supports higher-frequency signal paths and active filtering. The TLV274IN is based on a voltage-feedback amplifier architecture, as identified in the verified comparison data. In a typical application, one channel is used for amplification, another for buffering, and the remaining channels for filtering or instrumentation. Its rail-to-rail output supports low-voltage systems where the signal must use much of the available supply range. Typical applications include sensor-interface circuits, data-acquisition signal chains, low-frequency filters, buffered analog controls, portable instrumentation, and embedded measurement systems. The 16 V maximum supply makes it suitable for systems operating below industrial transient voltages, provided the design does not exceed the device rating. When laying out a TLV274IN board, keep the unused amplifier inputs biased to a valid common-mode level and place input and feedback components close to the relevant pins. Check the required output swing, load, stability, and supply-bypass requirements against the manufacturer datasheet before committing the design.
TLV274IPW - 3MHz Quad Rail-to-Rail Op Amp | Texas Instruments
Texas Instruments TLV274IPW is a four-circuit, low-power operational amplifier featuring 3 MHz gain-bandwidth product, 2.4 V/µs slew rate, and rail-to-rail output operation from a 2.7 V to 16 V supply. Each amplifier draws 550 µA, and the device is offered in a 14-pin TSSOP package rated for an extended industrial temperature range of -40°C to +125°C. An operational amplifier is a voltage-feedback analog IC that amplifies the difference between its differential inputs while rejecting signals common to both inputs. The TLV274 belongs to the operational-amplifier hierarchy, where it serves as a low-dropout signal-conditioning building block within analog, mixed-signal, instrumentation, and embedded-control systems. Rail-to-rail output capability lets its output approach the supply rails, improving dynamic range in low-voltage designs where conventional fixed-output amplifiers would lose useful signal range. The TLV274 combines a 3 MHz bandwidth with low 550 µA-per-channel supply current, making it suitable for portable and industrial systems that require higher bandwidth than ultra-low-power amplifiers but lower power consumption than high-speed general-purpose devices. Its 2.4 V/µs slew rate supports faster output transitions, while 39 nV/Hz input voltage noise helps preserve small-signal fidelity in filtering and sensor-conditioning circuits. Input bias current is specified at 39 pA, supporting high-impedance source applications. The device operates across a broad 2.7 V to 16 V supply range and uses a CMOS voltage-feedback architecture. Four independent amplifiers in one package reduce board area in applications requiring parallel signal channels. Its rail-to-rail output stage is the defining feature relative to the TLC27x family, although input common-mode behavior and noise characteristics must still be checked against the system requirements. Typical uses include portable instrumentation, low-side current measurement, sensor amplification, active filters, buffer stages, and general-purpose signal conditioning. In a current-sense amplifier, the amplifier boosts the small voltage produced across a shunt resistor while its low bias current limits loading of the sensing element. In an active filter, the 3 MHz bandwidth provides headroom for closed-loop response above the filter corner frequency. Designers should confirm output-current capability, input common-mode range, unity-gain stability, and noise performance for the selected feedback topology. Decoupling capacitors should be placed close to the supply pins, and sensitive high-impedance inputs should use guarded, short traces to reduce leakage and interference.
TLV2760CD - 3.6V, 500kHz Micropower RRIO Op Amp with Shutdown | Texas Instruments
The Texas Instruments TLV2760CD is a single, micropower, rail-to-rail input/output operational amplifier with shutdown, specified for a 1.8 V to 3.6 V supply range, 500 kHz gain-bandwidth product, 20 µA typical quiescent current and an 8-pin SOIC package. An operational amplifier is a voltage-gain building block that compares two input terminals and drives its output to control loops, buffer levels, or amplify small sensor signals. The TLV2760 belongs to the hierarchy low-noise amplifier -> operational amplifier -> analog signal conditioning IC -> semiconductor, and its rail-to-rail (RRIO) input and output stages let it operate directly across the full supply rails without headroom constraints. Key features of the TLV2760 include 500 kHz bandwidth from only 20 µA of supply current, rail-to-rail inputs and outputs, a shutdown pin for reducing supply current when the amplifier is idle, 3.5 mV typical offset voltage, and approximately 3 pA input bias current. The wide common-mode input range reaches both supply rails, which simplifies sensor front-ends powered directly from cells. Architecturally, the device is a CMOS single-supply amplifier that is fully specified down to a 1.8 V rail and characterized at 1.8 V and 2.4 V supply conditions. The maximum recommended supply voltage of 3.6 V permits operation from 1.8 V supplies down to 0.9 V (two AA or AAA cells), giving designers flexibility for energy-harvesting and portable systems. Typical applications include portable sensor conditioning, battery-powered instrumentation, low-power filter stages, transimpedance pre-amplifiers for photodiodes and pH electrodes, and general embedded signal conditioning where board area and supply current are tightly constrained. When designing with the TLV2760, keep the shutdown pin compatible with the host logic levels and observe the maximum recommended supply voltage of 3.6 V. Because the amplifier is intended for low-voltage rails, verify that any external feedback network and the surrounding ADC front end operate at compatible common-mode and output swing levels. This page consolidates distributor availability, drop-in replacement candidates, comparison data and practical layout guidance in one place, so engineers can shortlist the part faster than by reading a datasheet alone.
TLV2760ID - 500kHz RRIO Op Amp with Shutdown | Texas Instruments
The Texas Instruments TLV2760ID is a single, micropower rail-to-rail input and output operational amplifier with shutdown, 500 kHz gain-bandwidth product, 20 µA typical supply current, and a maximum supply voltage of 3.6 V. It is housed in an 8-pin SOIC package and is intended for low-voltage, low-power signal-conditioning systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Rail-to-rail input and output, commonly abbreviated RRIO, allows the input common-mode range and output swing to approach the supply rails. This makes the TLV2760ID useful in portable instrumentation, sensor interfaces, battery-powered monitoring, and low-voltage control systems where the usable signal range is limited. Key characteristics include a 500 kHz bandwidth, operation down to 1.8 V, a 3.6 V maximum recommended supply voltage, and approximately 20 µA of supply current. The shutdown function provides a way to reduce power consumption when the amplifier is not needed. According to the manufacturer datasheet, the TLV2760ID is specified for an industrial temperature range of -40°C to +85°C and offers 3500 µV typical input offset voltage. The TLV2760ID combines a single amplifier with rail-to-rail inputs and outputs in an 8-pin SOIC footprint. Its 500 kHz bandwidth is sufficient for general-purpose signal conditioning, active filtering, low-frequency sensor amplification, and embedded analog measurement. The shutdown control makes it particularly useful in duty-cycled systems where the analog channel must be disabled between measurements. Typical applications include battery-operated sensor interfaces, portable medical monitoring, industrial control modules, low-voltage data acquisition, buffer stages, and active filters. Its 1.8 V minimum operating supply supports systems powered from one lithium cell or from low-voltage energy-harvesting rails. The maximum recommended supply of 3.6 V prevents accidental operation from a higher-voltage source without proper regulation. When using the TLV2760ID, check the input and output common-mode limits for the actual supply voltage and load. Decoupling capacitors should be placed close to the supply pins, and the shutdown logic must remain in a defined state during startup. Output loading and capacitive loads can affect stability, so verify the final circuit against the application information in the manufacturer datasheet. This page combines the principal electrical and packaging details with application guidance, design checks, and carefully qualified replacement options. It also highlights where shutdown polarity, supply voltage, bandwidth, and package compatibility must be reviewed before treating another amplifier as a true drop-in replacement.
TLV2760IP - 500kHz RRIO Op Amp with Shutdown | Texas Instruments
Texas Instruments TLV2760IP is a single-supply, rail-to-rail input and output operational amplifier with shutdown, 500 kHz gain-bandwidth product, and operation down to 1.8 V. It is packaged in an 8-pin PDIP and intended for low-voltage, low-power signal-conditioning systems. The family combines rail-to-rail input and output operation, low quiescent current, and shutdown control in a through-hole package. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TLV2760 belongs to the operational-amplifier hierarchy, which includes rail-to-rail amplifiers, micropower amplifiers, and general-purpose analog ICs. Rail-to-rail input operation allows the input common-mode range to extend close to the supply rails, while rail-to-rail output operation improves output swing in low-voltage systems. The TLV2760 family provides 500 kHz bandwidth from approximately 20 microamperes of quiescent current and supports operation down to 1.8 V. The TLV2760IP is the high-offset-voltage member of the family, with a listed offset-voltage rating of 3500 microvolts. Its shutdown function allows a system designer to reduce supply current when the amplifier is not required, which is valuable in portable and battery-powered equipment. The low operating voltage and rail-to-rail behavior make the device suitable for sensor interfaces, transducers, battery-powered instrumentation, audio signal paths, and embedded control systems. Its 500 kHz bandwidth provides enough bandwidth for general-purpose feedback and error-amplifier networks without the higher power and noise associated with much faster amplifiers. The 8-pin PDIP package supports through-hole assembly and prototype rework, while its exposed lead spacing follows the standard 8-pin PDIP footprint. Designers should verify the shutdown-logic polarity, input bias behavior, output swing, and stability requirements against the manufacturer datasheet before using the amplifier near supply limits. This page combines the TLV2760IP electrical characteristics, lifecycle information, package data, sourcing workflow, and practical replacement guidance. It also highlights the distinctions among TLV276x offset-voltage options so engineers can select a pin-compatible family member without overlooking offset or shutdown requirements.
TLV2761CD - 500 kHz RRIO Op Amp | Texas Instruments
The Texas Instruments TLV2761CD is a single-amplifier, rail-to-rail input and output operational amplifier with 500 kHz gain-bandwidth product, 3.6 V maximum recommended supply voltage, and low 20 µA quiescent-current operation. It is housed in an 8-pin SOIC package and is intended for compact, low-power analog signal-conditioning systems operating from a 3.6 V maximum supply. An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify, buffer, compare, filter, or reshape analog signals. The TLV2761 belongs to the rail-to-rail input and output amplifier family, where the input common-mode range and output swing approach the supply rails. This makes the device useful where signals can occupy much of the available supply range and where conventional input stages would clip. Key features include 500 kHz gain-bandwidth product, operation down to 1.8 V, and approximately 20 µA quiescent current. The rail-to-rail input stage supports direct sensing of low-amplitude signals, while the rail-to-rail output stage provides useful dynamic output range. These characteristics make the amplifier appropriate for battery-powered sensing, low-voltage instrumentation, buffered analog measurement, and embedded control systems. The TLV2761CD uses a CMOS-based operational-amplifier architecture optimized for low-voltage operation. A single circuit is sufficient when an application requires one independent gain stage, comparator-style buffering, or a basic active filter. The 500 kHz bandwidth supports moderate-frequency signal paths without requiring the higher current and power consumption associated with faster general-purpose amplifiers. Typical uses include sensor signal conditioning, low-voltage ADC drivers, portable measurement instruments, industrial process monitoring, battery-operated diagnostic equipment, and embedded control interfaces. The low quiescent current is particularly valuable in designs that spend substantial time between measurement events because the amplifier's own supply demand remains small during those intervals. When designing around the TLV2761CD, verify the required output swing against the actual load and supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. Because rail-to-rail operation can involve input or output transition regions, input and output signals should be evaluated across the full operating range rather than only at the nominal supply voltage. This page combines the manufacturer product information with package, ordering, drop-in comparison, application guidance, and design considerations. The resulting reference helps engineers evaluate the TLV2761CD for low-voltage analog systems while keeping footprint compatibility and circuit-level constraints in view.
TLV2761ID - 500kHz RRIO Micro-Power Op Amp | Texas Instruments
The Texas Instruments TLV2761ID is a single-circuit, rail-to-rail input/output operational amplifier designed for low-voltage, low-power signal conditioning. It operates from a 1.8 V supply, supports supply voltages up to the recommended 3.6 V maximum, and provides a 500 kHz gain-bandwidth product while drawing only 20 µA of operating current. The device is offered in an 8-pin SOIC package for the industrial temperature range from -40°C to +85°C. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs while using feedback to set the closed-loop gain. The TLV2761 belongs to the rail-to-rail-input/output, or RRIO, family of voltage-feedback amplifiers. Rail-to-rail input operation improves dynamic range in low-voltage systems because the input common-mode range can extend toward both supply rails, while rail-to-rail output operation provides useful output swing near the available supply limits. The TLV2761ID combines 500 kHz bandwidth with approximately 20 µA operating current, making it suitable for portable and low-energy systems where converter size, signal bandwidth, and current consumption are all important. Its single-supply architecture supports operation from 1.8 V, a useful voltage range for coin cells, two alkaline cells, and low-voltage sensor systems. The single amplifier configuration also avoids unnecessary circuit area when only one gain stage is required. The TLV2761 family provides rail-to-rail input and output capability in a compact low-power implementation. Its 500 kHz bandwidth is sufficient for low- and moderate-frequency precision signal paths, including sensor interfaces, current measurements, and buffered analog signals. The 20 µA operating current supports energy-efficient acquisition systems, although a design requiring high closed-loop gain must confirm that the resulting settling behavior and noise meet its bandwidth requirements. Because the maximum recommended supply voltage is 3.6 V, the TLV2761ID should not be treated as a conventional 5 V or higher-voltage amplifier. Designators commonly use single, positive supply operation for battery-powered instrumentation. The device is available in an 8-pin SOIC package, simplifying assembly on both prototype boards and production PCBs using standard surface-mount processes. When connecting external circuitry, keep feedback resistors close to the amplifier pins and route input and output traces away from switching nodes and high-current paths. Decoupling capacitors should connect to a low-impedance ground plane with short traces. Because RRIO amplifiers can operate close to their supply rails, input and output signals must remain within the device's absolute maximum and operating limits, including during power-up and shutdown transitions. This page combines the Texas Instruments product specifications with practical selection, replacement, layout, and sourcing guidance. It also identifies the distinction between electrically similar TLV2761 ordering codes and explains why package, temperature grade, and shutdown capability must be checked before treating any replacement as a true drop-in choice.
TLV2761IP - 500kHz Micropower RRIO Op Amp | Texas Instruments
The Texas Instruments TLV2761IP is a single 3.6 V, 500 kHz, rail-to-rail input and output operational amplifier in an 8-pin PDIP package. It combines a low 20 µA supply current with rail-to-rail signal handling and is intended for portable, low-power, and general-purpose analog signal-conditioning systems. The device is identified as the I-grade, PDIP-package member of the TLV2761 family. An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, compare, and filter signals. The TLV2761 belongs to the operational amplifier hierarchy, where its rail-to-rail input and output stages allow signals close to the positive and negative supply rails to be processed more effectively than with a conventional input stage. This makes it useful in sensor interfaces, low-voltage signal chains, and portable instrumentation. The TLV2761IP operates from a single supply of up to 3.6 V and provides 500 kHz gain-bandwidth performance. Its typical supply current is 20 µA, supporting battery-powered and energy-conscious designs. Rail-to-rail input and output operation extends usable signal range within the supply limits, while the general-purpose amplifier configuration provides a practical solution for low-frequency amplification, buffering, and thresholding functions. The 8-pin PDIP format supports through-hole construction and is useful for prototypes, educational platforms, manually wired test equipment, and designs that benefit from socketed or easily inspected assemblies. Unlike a surface-mount package, the PDIP outline provides generous spacing between leads, making it easier to access with conventional bench instruments. Care is still required to maintain clean supply grounding and stable feedback networks when the amplifier is installed on a prototyping board. Typical uses include low-voltage sensor interfaces, current or voltage sensing, portable measurement systems, threshold comparators, audio-level conditioning, and general analog signal buffering. In a battery-powered design, its 20 µA typical supply current is the principal power-budget benefit, although actual system consumption also depends on the operating mode, load, and external network. The 500 kHz bandwidth supports moderate-frequency closed-loop operation rather than high-speed signal processing. Designers should confirm the minimum and maximum supply voltage, input common-mode limits, output swing, shutdown behavior, and stability requirements from the manufacturer datasheet before finalizing the circuit. Decoupling capacitors should be placed close to the supply pins, and feedback components should be selected with the amplifier's recommended operating region in mind. The PDIP package also requires adequate clearance from nearby conductive parts during soldering and inspection. This page consolidates the manufacturer product identity, verified package and performance information, pin-document location, purchasing workflow, and engineering considerations into a focused guide. It is designed to help engineers confirm fit, assess application suitability, and plan a replacement review without reducing the TLV2761IP to a distributor listing summary.
TLV2762CD - 3.6V 500kHz Dual RRIO Op Amp | Texas Instruments
Texas Instruments TLV2762CD is a dual, micropower, rail-to-rail input/output operational amplifier designed for low-voltage signal conditioning. It operates from a single 1.8 V to 3.6 V supply, provides 500 kHz unity-gain bandwidth, and is packaged in an 8-pin SOIC. Each channel combines rail-to-rail inputs and outputs with 95 nV/√Hz input-voltage noise, making it suitable for battery-powered instrumentation, sensor interfaces, and precision analog signal paths. An operational amplifier is an active analog circuit that amplifies the voltage difference between two inputs while using negative feedback to control gain and bandwidth. A rail-to-rail input stage accepts signals close to the supply rails, while a rail-to-rail output stage can produce output voltages near either rail. This capability improves dynamic range in systems whose signal range approaches the available supply voltage. The TLV2762 belongs to the operational-amplifier hierarchy, specifically the low-voltage, low-power, rail-to-rail amplifier class. The two independent amplifier channels can perform filtering, buffering, level shifting, transimpedance conversion, and differential sensing. Key characteristics include 500 kHz bandwidth, 230 V/ms slew rate, 550 µV typical offset voltage, 6 µV/°C typical offset drift, 15 pA typical input-bias current, and 20 µA typical amplifier supply current. Rail-to-rail input and output operation allow signals to use nearly the complete 1.8 V to 3.6 V supply range. The 500 kHz bandwidth gives useful closed-loop performance for moderate-frequency signals while keeping quiescent current low at 20 µA per amplifier. This bandwidth-to-power balance is appropriate for portable sensor nodes, where a higher-speed amplifier may add unnecessary supply demand. The 230 V/ms slew rate preserves large-signal response, while the 95 nV/√Hz noise density supports low-noise measurement of slow analog signals. Typical uses include battery-powered sensor conditioning, portable medical monitoring, industrial current measurement, low-voltage data acquisition, and general-purpose analog filtering. In each case, the device can operate directly from a 1.8 V rail and provide input or output headroom that is difficult to obtain with a conventional non-rail-to-rail amplifier. Designers should verify input and output common-mode limits, output swing, capacitive-load stability, and noise performance under the intended supply and load conditions. Place bypass capacitors close to the supply pins, keep feedback routing compact, and avoid excessive loading on the output. Although the SOIC-8 outline supports conventional board assembly, the low package thermal limit still requires consideration of power dissipation during sustained high-output-current operation. This page organizes the TLV2762CD electrical characteristics, package information, verified drop-in candidates, application guidance, and design considerations into a compact engineering reference for low-voltage analog design.
TLV2762ID - Dual 1.8V 500kHz RRIO Op Amp | Texas Instruments
The Texas Instruments TLV2762ID is a dual, micropower, rail-to-rail input and output operational amplifier designed for single-supply systems operating from 1.8 V to 3.6 V. It combines 500 kHz gain-bandwidth product, approximately 20 microampere quiescent current, and rail-to-rail operation in an 8-pin SOIC package. These characteristics make the TLV2762ID suitable for portable instrumentation, battery-powered sensing, low-power signal conditioning, and mixed-voltage interfaces. An operational amplifier is a voltage-amplifying building block that uses high open-loop gain to control an output over a wide input range. Rail-to-rail input amplifiers accept signals close to the positive and negative supply rails, while rail-to-rail outputs can swing close to those limits under typical load conditions. Within the amplifier hierarchy, the TLV2762 belongs to the micropower operational-amplifier family and provides two amplifiers in one package for space-constrained designs. Key features include a 1.8 V minimum operating supply, 500 kHz bandwidth, approximately 20 microampere quiescent current, and rail-to-rail input and output capability. The low quiescent current limits the supply current drawn when both amplifiers operate continuously, making the device appropriate for portable equipment that spends significant time monitoring low-frequency sensor signals rather than processing high-bandwidth waveforms. The TLV2762ID combines a speed-versus-power balance that is useful in general-purpose signal chains. A 500 kHz gain-bandwidth product supports moderate closed-loop gains while retaining a compact, low-power implementation. Because the device operates from a single positive supply down to 1.8 V, it can be powered directly from low-energy systems without a negative rail. Designers should still check input and output common-mode limits, capacitive-load stability, output-current capability, and the exact operating limits in the manufacturer datasheet before fixing the circuit. Typical uses include low-voltage sensor amplifiers, portable measurement systems, current-sense signal conditioning, audio preamplification, and interface buffering. The 8-pin SOIC outline also supports standard surface-mount assembly and hand-soldering workflows. In designs where output noise or channel matching is more important than bandwidth, an application-specific dual amplifier with integrated filtering may provide a better system fit. A practical design rule is to keep input, feedback, and decoupling connections short, then verify stability with the actual source impedance and load capacitance. Place the supply-bypass capacitor close to the positive rail pin and route the ground return directly to the device ground pin. If the amplifier drives a long cable, ADC input, or capacitive load, add an isolation resistor close to the output and confirm settling behavior with oscilloscope measurements. This page combines the manufacturer product information, distributor listings, pin-level guidance, drop-in alternatives, and application-focused design notes to support faster component selection and PCB planning.
TLV2762IP - Dual 1.8V Micropower RRIO Op Amp | Texas Instruments
Texas Instruments TLV2762IP is a dual micropower rail-to-rail input/output operational amplifier with shutdown, optimized for low-voltage, low-power signal-conditioning systems. The device operates from a 1.8 V minimum supply and uses only 20 uA per channel in the stated low-power operating condition, with shutdown current listed as 10 nA per channel. Its rail-to-rail input and output behavior supports operation across the available supply range, while a 500 kHz gain-bandwidth product provides useful bandwidth for general-purpose signal processing. The TLV2762IP is packaged in an 8-pin PDIP package. The TLV2762 belongs to the operational-amplifier hierarchy, where an operational amplifier is a voltage-feedback analog IC used to amplify, buffer, filter, or condition low-level signals. A rail-to-rail input/output amplifier is designed to accept and produce signals close to the positive and negative supply rails, making it useful in battery-powered sensors, portable instrumentation, and low-voltage industrial control systems. The micropower operating current helps reduce the energy required by continuously powered measurement equipment. The principal electrical characteristics include 1.8 V operation, a maximum recommended supply voltage of 3.6 V, 500 kHz bandwidth, 20 uA per channel supply current, and 10 nA per channel shutdown current. The TLV2762 family is identified as providing rail-to-rail input/output operation and CMOS-compatible shutdown behavior. These characteristics make the part suitable for portable sensor interfaces, low-energy monitoring modules, battery-powered test equipment, and embedded analog signal-conditioning circuits. The device is intended for single-supply operation, with the signal path operating from one supply rail and ground. Design should include input and output capacitance appropriate to the application, stable feedback-network design, and careful routing to minimize parasitic effects. The TLV2762IP package is an 8-pin PDIP, which supports through-hole prototyping and insertion into conventional DIP footprints. This page combines manufacturer-family electrical characteristics, package information, sourcing guidance, and application-oriented design notes to support component selection and PCB implementation.
TLV2763IN - Dual 1.8V Micropower RRIO Op Amp | TI
Texas Instruments TLV2763IN is a dual, 1.8 V micropower rail-to-rail input/output operational amplifier with shutdown, packaged in a 14-pin PDIP. The two amplifier channels operate from a single supply, provide a typical gain-bandwidth product of 500 kHz, and are suitable for low-voltage, low-power signal-conditioning systems. The TLV2763IN combines rail-to-rail inputs and outputs with a typical supply current of 20 µA per channel. A rail-to-rail-input and rail-to-rail-output operational amplifier, commonly described as a RRIO amplifier, can accept input signals near the positive and negative supply rails while driving loads toward those limits. This makes the TLV2763IN useful when the usable input range must extend beyond conventional common-mode limits. As a dual amplifier in a 14-pin PDIP, it can implement two independent gain or buffer stages while simplifying through-hole prototype construction. Key characteristics include 1.8 V single-supply operation, dual-channel operation, 500 kHz typical gain-bandwidth product, 20 µA typical supply current per channel, and 10.2 mA typical output current. Shutdown support is particularly useful for battery-powered instrumentation because the amplifiers can be disabled when signal-chain activity is not required, reducing system power consumption. The TLV2763IN belongs to the operational-amplifier hierarchy, where it combines low input and output swing limits, low quiescent current, and moderate bandwidth. Its rail-to-rail behavior makes it appropriate for sensor interfaces, portable measurement systems, battery monitoring, and low-voltage analog signal chains. The shutdown function also supports duty-cycled acquisition circuits where preserving standby power is important. Typical applications include portable sensor conditioning, low-voltage data acquisition, current-loop signal processing, audio preamplification, and general-purpose dual-stage amplification. Its 500 kHz bandwidth is appropriate for low-frequency and moderate-bandwidth instrumentation rather than high-speed video or RF signal paths. The 10.2 mA typical output-current capability is sufficient for buffer and low-load drive applications. When designing around the TLV2763IN, account for the dropout region, output-capacitance stability requirements, input bias-current effects, and the shutdown logic level. Place input and output compensation components close to the relevant pins and avoid excessive capacitive loading at the output. Use the manufacturer datasheet pin-description table and typical application circuits to confirm external component values and logic thresholds before production release. This page combines the manufacturer operating characteristics, package information, application guidance, and engineering-focused replacement analysis for the TLV2763IN. It also identifies the critical distinctions between genuine same-footprint alternatives and devices that are only functionally similar, helping engineers make a board-level decision without relying on incomplete catalog descriptions.
TLV2764ID - Quad 500kHz RRIO Op Amp | Texas Instruments
The Texas Instruments TLV2764ID is a quad, rail-to-rail input and output operational amplifier optimized for low-voltage, low-power signal conditioning. It operates from 1.8 V to 3.6 V, provides a 500 kHz gain-bandwidth product, and is packaged in a 14-pin SOIC. The four amplifiers share a common supply range and provide a practical combination of low quiescent current and useful closed-loop bandwidth for portable and industrial systems. An operational amplifier is a high-gain, differential-input analog building block used to amplify, buffer, filter, compare, or reshape signals. The TLV2764 belongs to the rail-to-rail input/output amplifier family within the broader operational amplifier, analog IC, and semiconductor hierarchies. Rail-to-rail input operation increases the usable input range near either supply rail, while rail-to-rail output operation improves output swing on low-voltage systems where conventional amplifier headroom is limited. The TLV2764ID integrates four amplifiers in one package, reducing board area and simplifying multi-channel designs. Key characteristics include a 500 kHz bandwidth, approximately 20 uA supply current per amplifier, and operation down to 1.8 V. These features make the device suitable for sensor conditioning, current-voltage conversion, low-voltage filtering, and general-purpose embedded analog signal paths where power consumption and integration are important. The device is built for general-purpose analog applications operating across an industrial temperature range of -40 °C to 85 °C. Its 14-pin SOIC package supports conventional surface-mount assembly and is suitable for prototypes as well as production boards. The quad organization is especially useful when four related channels are needed, such as sensing multiple inputs, driving balanced circuitry, or implementing active filtering in compact instrumentation. Typical uses include battery-powered sensor interfaces, portable measurement systems, industrial control modules, low-voltage data-acquisition nodes, and embedded analog signal conditioning. A 500 kHz bandwidth supports signals well beyond slow sensor outputs while retaining the low supply current required by compact embedded systems. Its rail-to-rail behavior also makes it useful when signal levels occupy much of the available supply range. Designers should verify input and output common-mode limits, output-current capability, noise, offset, and stability requirements against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the recommended stable-input network. PCB grounding and signal routing should minimize parasitic feedback around high-gain stages. This page combines device specifications, practical application guidance, pin-package information, and a strict same-footprint replacement analysis. It also distinguishes functionally similar amplifier families from genuine pin-to-pin options so engineers can assess PCB reuse without mistaking general-purpose similarity for drop-in compatibility.
TLV2764IN - Quad 500 kHz RRIO Op Amp | Texas Instruments
Texas Instruments TLV2764IN is a quad, rail-to-rail input and output operational amplifier designed for low-voltage, low-power signal conditioning. Each amplifier supports supply voltages down to 1.8 V, operates from a maximum recommended supply of 3.6 V, and provides 500 kHz gain-bandwidth product while drawing only 20 µA per amplifier. The device is packaged in a 14-pin plastic dual in-line package (14-PDIP). An operational amplifier is a high-gain analog signal-conditioning IC used to amplify voltage differences, buffer sensors, drive analog-to-digital converter inputs, and implement filters or feedback-control loops. The TLV2764IN belongs to the operational-amplifier hierarchy, where rail-to-rail input and output operation extends signal range and output swing toward the supply rails, making the device useful in compact battery-powered and low-voltage embedded systems. The four amplifiers provide rail-to-rail inputs and outputs, 500 kHz bandwidth, and operation from 1.8 V to 3.6 V. These characteristics suit low-energy sensor interfaces, portable measurement equipment, audio signal conditioning, and general-purpose analog control. The 20 µA per-amplifier operating current helps reduce the power burden in systems where four active analog channels are required, while the small bandwidth avoids introducing unnecessary high-frequency gain in precision measurement paths. Each channel includes an input common-mode range that extends to both supply rails, and the output stage is designed for rail-to-rail swing. These features simplify signal conditioning when the source can approach either supply rail. The quad organization also reduces the number of packages and board connections needed for systems implementing four independent amplifier functions or several instrumentation stages. Typical uses include low-voltage sensor front ends, battery-powered monitoring, analog-to-digital converter signal conditioning, active filters, and general-purpose buffering. The 14-PDIP package is suitable for through-hole prototypes, educational platforms, and industrial or instrumentation assemblies where the larger package simplifies hand insertion and inspection. Designers should verify input and output common-mode limits, capacitive-load stability, output-current capability, and noise performance against the application operating conditions. Place bypass capacitors close to the supply pins and maintain a clean return path to minimize supply noise and ground-offset errors. This page consolidates the key electrical specifications, package information, functional alternatives, and design considerations needed for initial component selection. For a new design, compare the complete TLV2764 family and package options in the manufacturer datasheet, especially when shutdown control, temperature grade, or package footprint differs from the TLV2764IN requirements. Validate the final amplifier configuration with the intended source impedance, load, supply tolerance, and environmental conditions before production release.
TLV2765CD - 1.8V Micro-Power Quad Op Amp | Texas Instruments
The Texas Instruments TLV2765CD is a quad, 1.8 V micro-power rail-to-rail input/output operational amplifier with shutdown, packaged in a 16-pin SOIC. It supports supply voltages up to 3.6 V, consumes approximately 20 uA per channel, and offers a 500 kHz gain-bandwidth product. The TLV2765CD also provides a shutdown current of approximately 10 nA per channel, making it suitable for portable and low-power signal-processing systems. A rail-to-rail input/output operational amplifier is a general-purpose amplifier whose input and output stages operate close to the supply rails. This topology allows the TLV2765CD to process low-voltage signals without requiring a midpoint-bias reference near mid-supply. As a quad amplifier, it combines four amplifier channels, shutdown control, and CMOS input characteristics in one 16-pin SOIC package, reducing board area when several low-voltage signals must be conditioned. The principal features include a low 1.8 V operating supply, a maximum supply voltage of 3.6 V, rail-to-rail input and output operation, and approximately 20 uA of supply current per channel. Shutdown reduces the supply current to approximately 10 nA per channel. The family datasheet identifies a 500 kHz bandwidth for the TLV2765 device and an input offset voltage of 3500 uV for the CD grade. These characteristics make the amplifier appropriate for battery-powered instrumentation, sensor interfaces, and low-voltage analog signal chains. The TLV2765 belongs to the TLV2764 and TLV2765 family of CMOS operational amplifiers with shutdown. Its rail-to-rail input stage supports operation near the lower and upper limits of the supply, while the rail-to-rail output stage provides useful output swing on low-voltage rails. Because the device is intended for micropower systems, total quiescent current and shutdown behavior are central to its system-level power budget. Typical uses include portable sensor conditioning, low-voltage transimpedance stages, battery-powered monitor circuits, general-purpose analog filtering, and embedded data-acquisition interfaces. Designers can use the four channels for gain, buffering, level shifting, active filtering, or comparator-style functions where open-loop operation is appropriate. The shutdown function is useful when one subsystem must be disconnected while the rest of a low-power instrument remains active. PCB design should keep input and feedback paths short and place input-referenced bypass capacitance close to the supply pins. Check output swing against the selected input and output voltages, because rail-to-rail operation does not guarantee a full rail-to-rail output under every load. For stable operation in amplifier configurations, follow the capacitance limits and recommended feedback values in the family datasheet. This product page combines the TLV2765CD operating characteristics with package guidance, application analysis, comparison criteria, and practical design notes. It is intended to help engineers evaluate the TLV2765CD for low-voltage, micro-power signal-processing designs before finalizing a PCB or production BOM.
TLV2765ID - Quad 3.6V Micro-Power RRIO Op Amp | Texas Instruments
Texas Instruments TLV2765ID is a quad, general-purpose operational amplifier with rail-to-rail input and output operation, a 3.6 V maximum supply, 500 kHz gain-bandwidth product, and shutdown support, all in a 16-pin SOIC package. It operates from 1.8 V to 3.6 V and supports low-voltage, low-power signal-chain designs requiring four amplifiers in one package. An operational amplifier is a high-gain, low-output-impedance analog building block used to amplify, buffer, filter, compare, and drive signals. The TLV2765 belongs to the micropower operational-amplifier hierarchy, combining low-voltage operation, rail-to-rail input/output capability, and a shutdown function in one quad device. Its four amplifiers make it useful when board area, supply current, and component count matter more than very high bandwidth. The principal operating features are a 3.6 V maximum supply, 500 kHz unity-gain bandwidth, rail-to-rail inputs and outputs, approximately 20 µA typical supply current per amplifier, and a shutdown pin. These characteristics suit battery-operated instrumentation, portable sensing, low-voltage industrial measurement, and general analog signal conditioning where a 5 V supply is unavailable or undesirable. The TLV2765 combines four rail-to-rail operational amplifiers in one SOIC-16 device. Rail-to-rail input capability keeps the usable common-mode input range close to the supply rails, while rail-to-rail output capability provides improved dynamic range when the output must approach either supply limit. The shutdown control provides a way to reduce operating current when the measured or amplified signal is not needed, although switching and output-state details should be confirmed in the manufacturer datasheet before sequencing the rails. Typical uses include portable sensor interfaces, low-voltage transimpedance stages, active filters, battery monitoring, audio and communication signal conditioning, and general-purpose embedded analog channels. In a four-channel sensor interface, the quad organization can reduce external component count and simplify power routing. In portable equipment, the low-voltage supply and micropower operation help control energy use, while the 500 kHz bandwidth provides enough response for many low-to-moderate-frequency measurement paths. Designers should keep input and output signal amplitudes within the linear operating region, account for output-swing limits near the supply rails, and observe the shutdown pin's required logic levels. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes and high-current return paths. Stable operation also depends on the source impedance, load, and feedback network selected for the intended gain. This product page consolidates the TLV2765ID operating limits, package information, sourcing path, replacement considerations, and practical PCB guidance. It is intended to help engineers determine whether a low-voltage, four-amplifier SOIC solution satisfies the precision, power, and layout requirements of a new analog design.
TLV2765IN - Quad 3.6V 500kHz RRIO Op Amp | Texas Instruments
The Texas Instruments TLV2765IN is a quad, low-power, rail-to-rail input/output operational amplifier operating from a 1.8V minimum supply up to the 3.6V maximum recommended supply. It provides 500kHz gain-bandwidth product, approximately 20uA supply current per channel, and a shutdown function that reduces shutdown current to 10nA per channel. The device is supplied in a 14-pin through-hole DIP package. An operational amplifier is a voltage-gain building block used to amplify, buffer, filter, compare, and control analog signals. The TLV2765 belongs to the operational-amplifier hierarchy, where rail-to-rail input and output operation helps the amplifier process signals near the positive and negative supply rails. The TLV2765 family combines this signal-handling capability with low quiescent current and shutdown control for portable and low-power systems. Key features include four amplifier channels, CMOS-compatible rail-to-rail inputs, rail-to-rail outputs, a 500kHz gain-bandwidth product, and operation from 1.8V to 3.6V. The approximately 20uA per-channel supply current supports battery-powered equipment where every microampere affects useful runtime. A common shutdown pin can disable all four channels, while the 10nA per-channel shutdown current limits backup and standby consumption. The wide common-mode input range makes the TLV2765 useful when signals approach either supply rail. Its 500kHz bandwidth supports low-frequency signal conditioning, sensor interfaces, filtering, and general instrumentation rather than high-speed video or RF amplification. The 3.6V maximum recommended supply also permits operation from two AA or AAA cells, although designers should account for cell-voltage variation and confirm the required headroom. Typical applications include portable measurement systems, low-voltage sensor interfaces, battery-powered instrumentation, analog signal conditioning, and industrial control modules. Shutdown is particularly useful when a system must periodically enter a low-power state without completely losing its supply. In multi-amplifier designs, the common shutdown control can simplify state management across all four channels. Designers should verify output current, output swing, input bias behavior, and stability against the specific load and signal amplitude. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a defined common-mode voltage to prevent unstable operation. This page combines the manufacturer device information, package characteristics, application guidance, parameter comparisons, and practical design notes to support component selection and PCB implementation for the TLV2765IN quad rail-to-rail operational amplifier.
TLV2770CD - 5.1MHz RRO Op Amp | Texas Instruments
The Texas Instruments TLV2770CD is a single, rail-to-rail-output CMOS operational amplifier with a 2.7 V minimum supply, 5.5 V maximum supply, 5.1 MHz gain-bandwidth product, and 10.5 V/µs slew rate. The device also includes shutdown capability and is packaged in an 8-pin SOIC. These characteristics place it between the TLV2770 family’s precision-focused CMOS architecture and the requirements of high-speed signal-conditioning systems. A CMOS operational amplifier is a voltage-controlled, differential-input amplifier used to buffer, amplify, filter, or compare analog signals. Its place in the signal-chain hierarchy is signal conditioning within a larger analog or mixed-signal system. Rail-to-rail output capability allows the output to approach the supply rails more closely than a conventional fixed-output amplifier, improving dynamic range in low-voltage systems where every millivolt of signal headroom matters. The TLV2770CD’s principal features include its 5.1 MHz gain-bandwidth product, 10.5 V/µs slew rate, and rail-to-rail output operation. The 5.1 MHz bandwidth supports higher-frequency closed-loop designs than low-frequency precision amplifiers, while the 10.5 V/µs slew rate improves response to large, fast input steps. Its single-amplifier configuration reduces board area in designs that need one independent high-speed channel. A shutdown function can also reduce power use when the signal path is not required continuously. The TLV277x family combines CMOS power characteristics with rail-to-rail output swing, high output drive, and strong DC precision. The TLV2770 differs from related family members by retaining shutdown functionality, making power management an important distinction during replacement. Because the amplifier operates from a maximum 5.5 V supply, it is primarily intended for low-voltage systems and should not be treated as a direct replacement for an op amp rated for substantially higher supply voltages. Typical uses include active filtering, sensor signal conditioning, low-voltage data acquisition, audio and communication interfaces, and general-purpose analog amplification. The combination of 5.1 MHz bandwidth and 10.5 V/µs slew rate is useful when the signal must be amplified without adding excessive delay. The shutdown feature also makes the device suitable for portable equipment and partitioned analog systems that can disable an inactive channel. For layout, place the amplifier near the source and load to minimize trace capacitance and interference, and provide a solid ground reference. Decoupling capacitors should be connected close to the supply pins. Before using shutdown in a new design, consult the manufacturer pin description and truth table to confirm the required control level and operating state. This page combines the TLV2770CD’s principal technical characteristics, verified sourcing information, drop-in replacement analysis, application guidance, and design notes. It is intended to help engineers assess bandwidth, supply voltage, shutdown behavior, package compatibility, and PCB integration before committing the amplifier to a production design.
TLV2770CP - 5.1MHz R-R Op Amp | Texas Instruments
The Texas Instruments TLV2770CP is a single operational amplifier with a 5.5 V maximum supply voltage, 5.1 MHz gain-bandwidth product, 10.5 V/µs slew rate, and rail-to-rail output capability. It is packaged as an 8-pin PDIP and includes a shutdown function for low-power operation. These characteristics make it suitable for precision signal conditioning, data acquisition, instrumentation, and industrial control systems. An operational amplifier is a voltage-controlled differential amplifier used to amplify, buffer, filter, or compare small signals. The TLV2770 belongs to the general-purpose amplifier family within the broader signal-chain and analog IC hierarchy. Its rail-to-rail output allows the output voltage to approach the supply rails under suitable load conditions, while its shutdown input provides a direct means of reducing supply current when the signal path is not required. The 5.1 MHz gain-bandwidth product supports closed-loop operation over a broad range of signal frequencies, while the 10.5 V/µs slew rate improves large-signal response. A maximum supply voltage of 5.5 V positions the device for low-voltage analog systems. The shutdown function is valuable in portable and embedded equipment because it can disable the amplifier during inactive periods and reduce system power consumption. The TLV2770CP is specified for operation from a 2.7 V minimum supply, with a family maximum of 5.5 V. The single-amplifier configuration and 8-pin PDIP format simplify prototyping where a through-hole package is preferred. Because bipolar-style signal paths can behave differently near the supply rails, system-level settling and output swing should be evaluated at the actual supply voltage, load, and signal amplitude used in the finished circuit. Typical applications include low-level sensor conditioning, analog instrumentation, active filters, data-conversion front ends, buffer stages, and industrial process-control modules. The 5.1 MHz bandwidth is particularly useful when the circuit must process signals above the kilohertz range, while the 10.5 V/µs slew rate helps preserve fidelity on rapidly changing waveforms. Shutdown can be used to disable unused analog channels between measurement events. When implementing the device, place input and output decoupling capacitors close to the corresponding pins and keep feedback traces short to minimize noise pickup and parasitic capacitance. Do not assume that the output can reach either supply rail under every load condition; verify the output-voltage limits and load capability in the manufacturer datasheet for the chosen voltage and temperature. This page combines the device's electrical characteristics, package information, drop-in replacement guidance, application guidance, and engineering design notes. It also distinguishes true pin-compatible options from functionally similar amplifiers whose shutdown-pin arrangements differ, helping designers make package-compatible design decisions without assuming that similar specifications guarantee interchangeability.