بەرهەمەکان (3,200+)

INA240A2DR - 50V/V Bidirectional Current Sense Amplifier | Texas Instruments
INA240A2DR

INA240A2DR - 50V/V Bidirectional Current Sense Amplifier | Texas Instruments

The Texas Instruments INA240A2DR is a bidirectional, zero-drift current-sense amplifier with a fixed gain of 50 V/V, a -4 V to 80 V common-mode input range, and enhanced PWM rejection. It is packaged in an 8-pin SOIC and operates from a single 5.5 V supply. A current-sense amplifier is a specialized amplifier that measures the voltage developed across a shunt resistor placed in a current-carrying conductor. The INA240 belongs to the current-sense amplifier hierarchy within instrumentation amplifiers and analog signal-chain ICs. It converts the small differential shunt voltage into an amplified voltage proportional to current, supporting both positive and negative current measurement. The A2 gain code sets the nominal amplification to 50 V/V. Its wide common-mode range permits sensing current above ground, at ground, and down to -4 V, which is useful in systems with inductive flyback or ground-offset returns. Bidirectional operation means that the output can represent positive or negative current without changing the basic shunt arrangement. Enhanced PWM rejection helps suppress switching disturbances commonly encountered in motor-control and power-conversion systems. The device uses a zero-drift architecture intended to provide accurate current measurement over changing temperatures and time. The manufacturer describes the INA240 family as ultra-precise and optimized for shunt-based measurements. Because the output is proportional to the shunt differential voltage, the shunt resistance determines the conversion between current and amplifier output voltage. Typical uses include motor and solenoid current monitoring, power-converter feedback, battery current measurement, industrial control systems, and automotive-style PWM systems. The 8-pin SOIC format supports conventional surface-mount assembly and compact analog layouts. Placement close to the shunt helps minimize pickup from adjacent switching nodes. Designers should verify the complete pin configuration, recommended input filtering, output-voltage range, and absolute maximum ratings in the manufacturer data sheet before layout. Kelvin routing from the shunt terminals and careful grounding are especially important because small differential signals can be corrupted by shared copper impedance or high-current return paths. This page combines the manufacturer's core INA240 characteristics with exact-MPN commercial information, same-family drop-in options, application guidance, and practical PCB considerations for engineers evaluating the INA240A2DR in a current-measurement design.

RFQ پەیوەندی
INA240A2PW - 50V/V Bidirectional Current Sense Amp | Texas Instruments
INA240A2PW

INA240A2PW - 50V/V Bidirectional Current Sense Amp | Texas Instruments

Texas Instruments INA240A2PW is a bidirectional, precision current-sense amplifier with a gain of 50 V/V, a -4 V to +80 V common-mode voltage range, and an operating temperature range of -40 °C to +125 °C. The device is packaged in an 8-pin TSSOP (PW) package and is designed for high-side or low-side current measurement in systems exposed to fast common-mode transients. A current-sense amplifier is an instrumentation amplifier that measures the small voltage developed across a current shunt and converts it into an amplified voltage proportional to current. This device belongs to the instrumentation-amplifier and current-sense-amplifier hierarchy, where its differential measurement, low offset voltage, and common-mode rejection improve the accuracy of power, motor, solenoid, and battery monitoring systems. The A2 gain option provides 50 V/V amplification. The INA240 family operates from a 5.5 V supply and accepts common-mode voltages extending from -4 V to +80 V. Its enhanced PWM rejection is intended to suppress transient disturbance caused by switching power stages, while bidirectional operation allows measurement of positive or negative current without changing the signal path architecture. The common-mode range and PWM rejection make the INA240A2PW especially useful where the shunt is placed near a motor, actuator, or inductive load. Although the analog output must remain within the amplifier's supply-voltage limits, the input common-mode voltage can move independently across the stated -4 V to +80 V range. This separation between input common-mode capability and output-supply limits is central to correct application design. Typical uses include DC motor current control, solenoid and actuator monitoring, battery pack current measurement, industrial power conversion, and electronic loads. The precision architecture is also appropriate for systems that must recover a small shunt voltage accurately while rejecting rapidly changing voltages on the sensed power rail. For layout, route the two shunt connections as a compact, symmetric pair and minimize the area enclosed by those traces. Place the shunt and amplifier input network close together, use a low-value differential filter only where its added noise and settling behavior are acceptable, and terminate the amplifier output according to the ADC or analog front-end requirements. This page combines the manufacturer lifecycle information, verified distributor records, family-level alternatives, comparison criteria, and application-oriented design guidance for engineers evaluating the INA240A2PW as a current-sense amplifier for industrial and power-conversion systems.

RFQ پەیوەندی
INA240A3D - 80V Current Sense Amplifier | Texas Instruments
INA240A3D

INA240A3D - 80V Current Sense Amplifier | Texas Instruments

The Texas Instruments INA240A3D is a bidirectional, ultra-precise voltage-output current-sense amplifier with an operating common-mode range of -4 V to 80 V, enhanced PWM rejection, and an 8-pin SOIC package. It is designed to measure the voltage developed across a shunt resistor in high-side or low-side current-sensing circuits while supporting common-mode voltages above the device supply voltage. A current-sense amplifier is a specialized amplifier within the instrumentation-amplifier and signal-conditioning hierarchy. It converts the small differential voltage produced by a shunt resistor into a proportional analog voltage suitable for measurement by an ADC, MCU, motor controller, or protection circuit. The INA240 family is classified as an analog signal-chain IC and is commonly placed beside a power-conversion stage to create a precision current-feedback signal. The INA240A3D combines bidirectional measurement, a wide -4 V to 80 V common-mode range, and enhanced PWM rejection. Bidirectional operation allows the output polarity to represent either positive or negative current. The negative common-mode capability is useful when a shunt is observed during a below-ground flyback interval, while the upper range supports current monitoring in systems operating well above the amplifier supply voltage. Its stated operating-temperature range is -40 °C to 125 °C. The device uses a voltage-output architecture with reference and supply connections that support system-level current measurement. Because the amplifier can operate independently of the common-mode voltage being sensed, its performance is maintained in applications where the shunt voltage swings rapidly while the amplifier remains powered from a low-voltage rail. This architecture is particularly useful in motor drives, solenoid controls, power converters, and battery-powered systems where a conventional low-voltage current-sense amplifier may leave the measurement range. Typical uses include high-side DC-link monitoring, low-side motor-return measurement, solenoid current diagnostics, power-supply telemetry, and battery charge or discharge current sensing. In these systems, the shunt is placed in the current path and connected to the differential input of the INA240A3D. The resulting analog voltage can be routed to a control ADC or comparator for regulation, fault detection, or data logging. Design the input and reference network carefully because the differential shunt voltage, amplifier supply, output range, and selected shunt resistance jointly determine usable measurement range. Keep the shunt and amplifier connections compact to minimize parasitic pickup, use a Kelvin connection where practical, and route the differential pair away from switching-node copper. The manufacturer's INA240 datasheet should be used for pin assignments, gain, input limits, output behavior, and recommended application values. This page organizes the verified INA240A3D operating limits, package information, sourcing details, replacement constraints, application guidance, and design considerations. It also distinguishes a confirmed same-package automotive alternative from incompatible package or gain variants that cannot be treated as drop-in replacements.

RFQ پەیوەندی
INA240A3DR - 80V Current Sense Amplifier | Texas Instruments (Tape & Reel)
INA240A3DR

INA240A3DR - 80V Current Sense Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments INA240A3DR is a bidirectional, ultra-precise voltage-output current-sense amplifier with an operating common-mode range of -4 V to 80 V, enhanced PWM rejection, and an 8-pin SOIC package. It is designed to measure the voltage developed across a shunt resistor in high-side or low-side current-sensing circuits while supporting common-mode voltages above the device supply voltage. A current-sense amplifier is a specialized amplifier within the instrumentation-amplifier and signal-conditioning hierarchy. It converts the small differential voltage produced by a shunt resistor into a proportional analog voltage suitable for measurement by an ADC, MCU, motor controller, or protection circuit. The INA240 family is classified as an analog signal-chain IC and is commonly placed beside a power-conversion stage to create a precision current-feedback signal. The INA240A3DR combines bidirectional measurement, a wide -4 V to 80 V common-mode range, and enhanced PWM rejection. Bidirectional operation allows the output polarity to represent either positive or negative current. The negative common-mode capability is useful when a shunt is observed during a below-ground flyback interval, while the upper range supports current monitoring in systems operating well above the amplifier supply voltage. Its stated operating-temperature range is -40 °C to 125 °C. The device uses a voltage-output architecture with reference and supply connections that support system-level current measurement. Because the amplifier can operate independently of the common-mode voltage being sensed, its performance is maintained in applications where the shunt voltage swings rapidly while the amplifier remains powered from a low-voltage rail. This architecture is particularly useful in motor drives, solenoid controls, power converters, and battery-powered systems where a conventional low-voltage current-sense amplifier may leave the measurement range. Typical uses include high-side DC-link monitoring, low-side motor-return measurement, solenoid current diagnostics, power-supply telemetry, and battery charge or discharge current sensing. In these systems, the shunt is placed in the current path and connected to the differential input of the INA240A3DR. The resulting analog voltage can be routed to a control ADC or comparator for regulation, fault detection, or data logging. Design the input and reference network carefully because the differential shunt voltage, amplifier supply, output range, and selected shunt resistance jointly determine usable measurement range. Keep the shunt and amplifier connections compact to minimize parasitic pickup, use a Kelvin connection where practical, and route the differential pair away from switching-node copper. The manufacturer's INA240 datasheet should be used for pin assignments, gain, input limits, output behavior, and recommended application values. This page organizes the verified INA240A3DR operating limits, package information, sourcing details, replacement constraints, application guidance, and design considerations. It also distinguishes a confirmed same-package automotive alternative from incompatible package or gain variants that cannot be treated as drop-in replacements.

RFQ پەیوەندی
INA240A3PWR - 100V/V Zero-Drift Current Sense Amp | TI
INA240A3PWR

INA240A3PWR - 100V/V Zero-Drift Current Sense Amp | TI

The Texas Instruments INA240A3PWR is a bidirectional, zero-drift current-sense amplifier with a gain of 100 V/V, a -4 V to 80 V common-mode input range, and enhanced PWM rejection, housed in an 8-pin TSSOP package. It measures the voltage developed across a shunt resistor and produces an analog output suitable for motor-control, power-delivery, and industrial monitoring systems. The wide common-mode range allows the shunt to remain above ground, below ground, or near an 80 V bus without requiring separate high-voltage sensing electronics. A current-sense amplifier is an analog signal-conditioning device that converts the small voltage across a current shunt into a larger, measurable voltage. The INA240 belongs to the instrumentation-amplifier and current-sense-amplifier hierarchy, where accurate offset behavior and common-mode rejection are essential for recovering a current measurement from a low-amplitude differential signal. Its output voltage represents the shunt differential voltage multiplied by a fixed gain of 100 V/V. The A3 gain version provides a nominal output of 1 V for every 10 mV across the shunt. Its zero-drift architecture reduces input-offset contributions that otherwise change with temperature, improving accuracy in systems that require stable current measurements over wide operating ranges. The -4 V to 80 V common-mode capability also supports sensing during transient intervals in systems containing inductive loads, while enhanced PWM rejection helps suppress errors produced by fast-switching motor-control waveforms. The INA240 family uses a voltage-output architecture and can measure current in either direction when the output is biased with a reference voltage. The reference pin permits the output to be centered around a nonzero voltage, which is important for systems that must report both positive and negative current without saturating the output at zero. A low typical supply current of 90 μA also helps reduce the overhead introduced by the measurement channel. Typical applications include three-phase inverter motor control, DC motor current monitoring, solenoid current tracking, battery-management systems, power-supply load reporting, and industrial actuator control. In a motor inverter, the device can sit beside the low-side shunt and retain usable operation through the switching transitions. In a bidirectional system, the reference voltage shifts the zero-current output level so that positive and negative current can be distinguished at a single analog input. Designers should place the shunt and amplifier inputs on a compact, symmetric trace arrangement, connect the reference pin to a low-impedance bias network when bidirectional output is required, and keep output routing away from high-voltage switching nodes. The power-supply and ground pins require careful decoupling, while input filtering should preserve the common-mode and timing performance needed by the application.

RFQ پەیوەندی
INA240A4D - 80V Bidirectional Current Sense Amp | Texas Instruments
INA240A4D

INA240A4D - 80V Bidirectional Current Sense Amp | Texas Instruments

The Texas Instruments INA240A4D is a bidirectional, zero-drift current-sense amplifier with a -4 V to 80 V common-mode range, enhanced PWM rejection, and an 8-pin SOIC package. It operates across a -40 °C to +125 °C temperature range and is designed to measure the voltage across a shunt resistor in systems where the sensed bus can move below ground or as high as 80 V. A current-sense amplifier is an instrumentation amplifier that converts the small differential voltage developed across a shunt resistor into a proportional, amplified output voltage. The INA240 family belongs to the amplifier and instrumentation-amplifier hierarchy, where precision gain, input offset behavior, common-mode rejection, and output accuracy determine how accurately a power circuit can be monitored. Bidirectional sensing allows the same device to report positive or negative current without changing the measurement topology. The INA240A4D provides 120 dB CMRR, a 100 kHz gain-bandwidth product, approximately 90 µA input bias current, and 1.8 mA operating supply current. Its zero-drift architecture supports current measurements in motor controls, solenoid drivers, battery systems, and industrial power supplies. Enhanced PWM rejection helps preserve measurement accuracy when rapid common-mode voltage transitions are present around inductive loads. The common-mode rating is independent of the amplifier supply voltage, allowing the INA240A4D to operate with a separate low-voltage supply while monitoring a high-voltage power bus. Its negative common-mode capability is particularly useful during the flyback interval of typical solenoid applications, when the voltage at the monitored node can fall below ground. The broad 80 V positive range supports higher-voltage industrial and automotive-style systems. Typical applications include motor-current feedback, solenoid-current monitoring, battery-pack current measurement, inverter control, power-supply telemetry, and current sharing. In each case, the shunt resistor converts current into a differential voltage, while the amplifier provides a measurable output for an ADC, controller, or protection circuit. Bidirectional operation is useful where energy can flow in either direction. For layout, place the shunt and input network close to the amplifier, keep the differential input traces compact and matched, and provide a stable bypass connection near the supply pins. The input filtering and gain-setting network must be checked against the intended current range because shunt resistance, amplifier gain, and ADC input range jointly determine the usable measurement span. This product overview combines the manufacturer specifications, package details, sourcing status, and application guidance needed to evaluate the INA240A4D. Because the manufacturer identifies this orderable variant as no longer in production, engineers should confirm lifecycle status and consider an active alternate during new design qualification.

RFQ پەیوەندی
INA240A4DR - 80V Bidirectional Current Sense Amp | Texas Instruments (Tape & Reel)
INA240A4DR

INA240A4DR - 80V Bidirectional Current Sense Amp | Texas Instruments (Tape & Reel)

The Texas Instruments INA240A4DR is a bidirectional, zero-drift current-sense amplifier with a -4 V to 80 V common-mode range, enhanced PWM rejection, and an 8-pin SOIC package. It operates across a -40 °C to +125 °C temperature range and is designed to measure the voltage across a shunt resistor in systems where the sensed bus can move below ground or as high as 80 V. A current-sense amplifier is an instrumentation amplifier that converts the small differential voltage developed across a shunt resistor into a proportional, amplified output voltage. The INA240 family belongs to the amplifier and instrumentation-amplifier hierarchy, where precision gain, input offset behavior, common-mode rejection, and output accuracy determine how accurately a power circuit can be monitored. Bidirectional sensing allows the same device to report positive or negative current without changing the measurement topology. The INA240A4DR provides 120 dB CMRR, a 100 kHz gain-bandwidth product, approximately 90 µA input bias current, and 1.8 mA operating supply current. Its zero-drift architecture supports current measurements in motor controls, solenoid drivers, battery systems, and industrial power supplies. Enhanced PWM rejection helps preserve measurement accuracy when rapid common-mode voltage transitions are present around inductive loads. The common-mode rating is independent of the amplifier supply voltage, allowing the INA240A4DR to operate with a separate low-voltage supply while monitoring a high-voltage power bus. Its negative common-mode capability is particularly useful during the flyback interval of typical solenoid applications, when the voltage at the monitored node can fall below ground. The broad 80 V positive range supports higher-voltage industrial and automotive-style systems. Typical applications include motor-current feedback, solenoid-current monitoring, battery-pack current measurement, inverter control, power-supply telemetry, and current sharing. In each case, the shunt resistor converts current into a differential voltage, while the amplifier provides a measurable output for an ADC, controller, or protection circuit. Bidirectional operation is useful where energy can flow in either direction. For layout, place the shunt and input network close to the amplifier, keep the differential input traces compact and matched, and provide a stable bypass connection near the supply pins. The input filtering and gain-setting network must be checked against the intended current range because shunt resistance, amplifier gain, and ADC input range jointly determine the usable measurement span. This product overview combines the manufacturer specifications, package details, sourcing status, and application guidance needed to evaluate the INA240A4DR. Because the manufacturer identifies this orderable variant as no longer in production, engineers should confirm lifecycle status and consider an active alternate during new design qualification.

RFQ پەیوەندی
INA250A1PW - 36V Bidirectional Current-Sense Amplifier | TI
INA250A1PW

INA250A1PW - 36V Bidirectional Current-Sense Amplifier | TI

The Texas Instruments INA250A1PW is a bidirectional, precision current-sense amplifier with an integrated shunt resistor, a 36 V common-mode range, and a gain of 20 V/V in a 16-pin TSSOP (PW) package. It is designed to measure positive and negative current while the measured conductor operates from 0 V to 36 V, independent of the amplifier supply voltage. The integrated precision shunt removes the external shunt-resistor element while preserving calibrated current measurement. A current-sense amplifier is a specialized instrumentation amplifier that converts the voltage across a current-sensing resistor into a proportional, low-level output voltage. The INA250 belongs to the current-sense amplifier hierarchy, where it supports precision measurement, power monitoring, motor control, industrial instrumentation, and protection systems. Its integrated shunt also reduces board area compared with a discrete shunt-resistor implementation. The device provides bidirectional measurement through an externally applied reference voltage. Positive current can move the output above the reference level, while negative current moves it below that level. This arrangement allows a unidirectional amplifier output to represent both load directions and supports applications that need absolute-value or signed-current information. The 0 V to 36 V common-mode range covers many industrial, automotive-adjacent, power-supply, and motor-system rails. The INA250A1PW uses the A1 gain option, which provides 20 V/V voltage gain. Its voltage-output architecture simplifies connection to analog-to-digital converters, comparators, controllers, and monitoring systems. Because the sensing element is integrated, PCB design must preserve the defined current path and provide adequate copper width and thermal capacity for the intended current level. The TSSOP package is a surface-mount package in the TSSOP-16 family. Typical applications include high-side power-supply monitoring, bidirectional motor-current measurement, industrial control systems, battery current sensing, solenoid monitoring, and electronic protection. In these systems, the amplifier reconstructs a current-proportional voltage that can be digitized or compared with a threshold. System calibration should account for the selected gain, reference voltage, ADC resolution, and the measurement bandwidth required by the load. Design attention should focus on Kelvin routing for the reference connection, filtering around the output when the measured waveform contains high-frequency noise, and thermal verification at maximum continuous current. The integrated shunt is convenient, but PCB copper, vias, pads, and connector geometry can limit practical current and increase temperature rise. Use the manufacturer pin-description table when assigning PCB tracks and the device data sheet for the complete recommended layout. This page combines the manufacturer device description, package and operating information, practical application guidance, replacement criteria, and engineering-oriented design notes. These resources help engineers evaluate the INA250A1PW beyond a basic distributor listing while keeping pin compatibility and measurement accuracy at the center of the selection process.

RFQ پەیوەندی
INA250A3PW - 36V Bidirectional Current Sense Amplifier | TI
INA250A3PW

INA250A3PW - 36V Bidirectional Current Sense Amplifier | TI

Texas Instruments INA250A3PW is a bidirectional precision current-sense amplifier with an integrated shunt resistor, 100 V/V gain, and operation from a 2.7 V to 36 V supply. The device measures low- and high-side current across common-mode voltages from 0 V to 36 V and is housed in a 16-pin TSSOP package. Its voltage output supports direct connection to analog-to-digital converters, controllers, and monitoring systems. A current-sense amplifier converts the voltage generated across a shunt resistor into a proportional, measurable voltage. This integrated-resistor implementation belongs to the current-shunt monitor class within precision amplifier and power-management ICs. By placing the shunt inside the amplifier package, it removes the need for a separate precision shunt while reducing layout sensitivity associated with external Kelvin connections. The INA250A3PW provides a gain of 100 V/V, allowing the 50 mΩ integrated shunt to support current measurements up to 15 A according to the family specifications. Bidirectional operation measures positive or negative current, and an external reference can establish the output operating point for zero-current offset or bipolar reporting. A 2.7 V minimum supply permits use in low-voltage systems while the 36 V supply rating supports higher-voltage industrial buses. The INA250 family specifies a maximum supply current of 300 µA and operation from -40 °C to 125 °C. Its integrated shunt and Kelvin-connected internal structure improve measurement accuracy by reducing lead and trace resistance effects. The voltage-output architecture requires downstream filtering and input/output stability capacitors selected according to the manufacturer datasheet, rather than relying on an internal shunt resistor placed outside the package. Typical applications include motor and solenoid current monitoring, power-supply telemetry, battery-pack management, industrial control systems, and high-side or low-side protection. The device can monitor current in systems whose supply voltage changes independently of the sensed common-mode voltage, making it useful in 24 V industrial equipment, automotive-style loads, and distributed power architectures. Design layouts should keep the power path short and use solid copper planes so that shunt heat is distributed rather than concentrated in a narrow trace. Confirm output saturation, reference-pin behavior, common-mode limits, and filter-component values against the manufacturer datasheet before operating at the 15 A family limit. This page combines device specifications, application guidance, pin and package considerations, lifecycle information, and verified replacement analysis. It also distinguishes electrically similar family members from true pin-compatible drop-in choices so that PCB reuse decisions are based on measurable electrical differences rather than package similarity alone.

RFQ پەیوەندی
INA253A1IPW - 80V Bidirectional Current Sense Amp | TI
INA253A1IPW

INA253A1IPW - 80V Bidirectional Current Sense Amp | TI

The Texas Instruments INA253A1IPW is an 80 V bidirectional precision current-sense amplifier with PWM rejection and an integrated 2 mΩ precision, low-inductance shunt resistor, packaged in a 20-pin TSSOP. The device accepts a supply voltage of 2.7 V to 5.5 V and operates across a -40°C to 125°C temperature range. It converts the voltage developed across the integrated shunt into an amplified analog output that can be measured by an ADC, controller, or protection circuit. A current-sense amplifier is a specialized amplifier that measures the voltage across a current sensor and produces an output proportional to the sensed current. The INA253 belongs to the instrumentation-amplifier and current-sensing IC hierarchy, where its integrated shunt combines current measurement with low-inductance sensing. This integration simplifies the power path and supports bidirectional measurement, allowing positive and negative current to be represented around a common zero-current output level. Key features include an 80 V common-mode input range, bidirectional current sensing, PWM rejection, zero-drift operation, and an integrated 2 mΩ shunt resistor. The A1 gain option provides a 50 V/V output ratio. The 20-pin TSSOP package provides a compact surface-mount format for industrial, automotive-adjacent, communications, and power-supply control systems where measured current must withstand substantial switching-node transients. The integrated shunt is the defining technical feature. A low-inductance sensing element limits the voltage spikes that would otherwise appear when current changes rapidly. The PWM-rejection architecture reduces disturbance from switching waveforms, while the zero-drift input stage improves accuracy around zero current. Compared with a discrete shunt-and-amplifier implementation, the INA253 reduces board area and component count while retaining the gain and common-mode ratings needed for demanding power-conversion circuits. Typical uses include DC-DC converter output-current monitoring, bidirectional motor-control current measurement, battery and power-path monitoring, and protection in industrial equipment. The 80 V common-mode capability is especially useful when the sensed conductor sits near a switching node. The integrated shunt also makes the device suitable for compact instrumentation where external Kelvin routing and discrete shunt placement would increase complexity. For PCB design, keep the high-current path electrically short and place the amplifier and its decoupling capacitors close to the supply pins. Review the manufacturer datasheet's layout example for the recommended shunt and grounding arrangement. Confirm that the analog output remains within the input range of the receiving ADC, and account for amplifier output swing and system offset when defining trip thresholds. This page combines the manufacturer's key INA253A1IPW specifications with same-package family alternatives, package details, application guidance, and selection considerations. It is intended to help engineers identify the correct gain and automotive options without overlooking common-mode rating, shunt integration, temperature range, or PCB-layout requirements.

RFQ پەیوەندی
INA253A2IPW - 80V Bidirectional Current Sense Amp | TI
INA253A2IPW

INA253A2IPW - 80V Bidirectional Current Sense Amp | TI

The Texas Instruments INA253A2IPW is a bidirectional, zero-drift current-shunt monitor with an integrated 2 mΩ shunt resistor, 200 mV/A gain, and a 20-pin TSSOP package. It operates from a 2.7 V to 5.5 V supply while monitoring common-mode voltages from -4 V to +80 V. The device combines precise current measurement with PWM rejection in a single surface-mount IC. A current-sense amplifier is an instrumentation amplifier that measures the small voltage generated across a shunt resistor and converts it into a proportional output voltage. The INA253 belongs to the current-sense amplifier hierarchy, where it bridges precision analog measurement and power-system monitoring. Integrating the shunt resistor reduces external component count and helps standardize the sensing element for bidirectional current applications. Key electrical features include 350 kHz -3 dB bandwidth, 2.4 V/µs slew rate, 90 pA input bias current, and 1.8 mA supply current. The A2 gain version produces 200 mV/V output for each ampere of sensed current. Its wide -4 V to +80 V common-mode range allows the shunt path to operate at high bus voltages while the amplifier itself remains powered from a low-voltage supply. Internally, the zero-drift architecture supports low offset behavior in precision measurement systems. The integrated precision shunt and chopper-stabilized amplifier are designed for systems where board space, component count, and current-direction measurement are important. Because the sensing element is integrated, PCB design should preserve the manufacturer-recommended current-path geometry and thermal conditions. Typical applications include motor-drive phase current monitoring, industrial power-supply control, battery current measurement, solenoid current sensing, and LED driver feedback. The -4 V to +80 V common-mode capability is particularly useful in systems where a shunt can be placed in a high-voltage conductor while the INA253 remains connected to a 2.7 V to 5.5 V control supply. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, especially for IN+, IN−, REF, OUT, and supply connections. Account for shunt heating at sustained high current and place input and reference components close to the device to minimize added error and pickup from fast-switching nodes. This page organizes the electrical characteristics, application guidance, confirmed family alternatives, and design trade-offs of the INA253A2IPW. It helps engineers distinguish what the integrated 2 mΩ solution provides from lower-current sensing approaches and from gain variants in the same INA253 family.

RFQ پەیوەندی
INA253A3IPW - 400mV/A Bidirectional Current Sense | Texas Instruments
INA253A3IPW

INA253A3IPW - 400mV/A Bidirectional Current Sense | Texas Instruments

The Texas Instruments INA253A3IPW is a precision current-shunt monitor with a 400 mV/A gain, an 80 V common-mode range, and an integrated 2 mΩ low-inductive shunt resistor in a 20-pin TSSOP package. It supports bidirectional current measurement from -4 V to +80 V while combining a zero-drift chopped amplifier with integrated shunt-resistor current sensing. A current-shunt monitor is an instrumentation amplifier that measures the small voltage generated across a precision shunt resistor as current flows through a conductor. The INA253 belongs to the current-sense amplifier hierarchy, where the amplified shunt voltage is filtered, digitized, or used for power monitoring and control. Its integrated resistor simplifies the sensing path, reduces external component count, and keeps the shunt geometry close to the amplifier for improved measurement repeatability. The A3 gain option provides 400 mV/A, while the INA253 family also includes 100 mV/A and 200 mV/A versions. The device operates over a -4 V to +80 V common-mode range, independent of its supply voltage, which supports high-side sensing in 48 V industrial, communications, automotive, and power-system environments. Its 350 kHz -3 dB bandwidth accommodates dynamic current measurements while providing rejection of PWM-related disturbances. The INA253A3IPW combines precision zero-drift signal conditioning with an integrated 2 mΩ shunt. Bidirectional operation allows the output to move above or below ground depending on current direction. The listed operating-temperature range is -40°C to +125°C, and the device is supplied in a 20-pin TSSOP package measuring 0.173 inch, or 4.40 mm, in width. Typical uses include server and telecom power rails, industrial motor controls, battery-management systems, LED drivers, solenoid drivers, and automotive load monitoring. In each application, the shunt monitor converts bidirectional current into a proportional analog voltage, allowing a controller to monitor load current, detect overcurrent, or implement closed-loop power management. PCB layout is critical because the integrated shunt and amplifier must be placed directly in the current path. High-current conductors should use short, wide copper, while the supply and ground connections should follow the manufacturer’s pin-assignment and layout guidance. Designers should also account for output settling, filter selection, and common-mode transient protection when operating near rapidly switching power stages. This product page combines the exact ordering information, electrical characteristics, family-level comparison, and application guidance needed to plan an INA253A3-based current-measurement design. It also identifies which same-package alternatives can be evaluated when gain, automotive qualification, or supply requirements differ.

RFQ پەیوەندی
INA293B1QDBVRQ1 - 110V, 1.3MHz Current Sense Amp | TI
INA293B1QDBVRQ1

INA293B1QDBVRQ1 - 110V, 1.3MHz Current Sense Amp | TI

The Texas Instruments INA293B1QDBVRQ1 is an AEC-Q100 qualified, ultra-precise bidirectional current-sense amplifier that measures voltage drops across shunt resistors over an exceptionally wide common-mode range from -4 V to +110 V. It delivers a 1.3 MHz small-signal bandwidth with a 20 V/V fixed gain (B1 variant) in a 5-pin SOT-23 (DBV) package, making it ideal for high-voltage, high-precision current monitoring in space-constrained automotive and industrial designs. What is a current-sense amplifier? A current-sense amplifier is a specialized analog building block that measures the small differential voltage developed across a shunt resistor placed in series with a load or supply rail, and converts it to a ground-referenced output voltage proportional to load current. Unlike a general-purpose op amp, a current-sense amplifier tolerates large common-mode voltages - often well above its own supply - and rejects the common-mode component, exposing only the shunt drop. The INA293-Q1 sits at the high-precision end of this category, combining low offset, low drift, and the widest common-mode range in TI's portfolio of unidirectional/bidirectional current-sense amplifiers. Key features include a maximum offset voltage of ±30 µV across temperature, ±0.2% gain error, and a quiescent current of approximately 1.5 mA over the -40 °C to +125 °C automotive grade-1 temperature range. The B1 gain variant provides 20 V/V; the B2, B3, B4, and B5 variants in the same family offer 50 V/V, 100 V/V, 200 V/V, and 500 V/V respectively, all sharing the SOT-23-5 footprint. The device operates from a single 2.7 V to 20 V supply and is robust against input transients well beyond its supply rail. Internally, the INA293-Q1 uses a precision chopped-input front end followed by a fixed-gain output stage, achieving CMRR greater than 100 dB at DC and PSRR above 80 dB at 1 kHz. The wide common-mode architecture supports both high-side and low-side sensing topologies, enabling accurate monitoring in 48 V mild-hybrid automotive systems, industrial 24 V/36 V/48 V rails, and telecom -48 V applications without level shifting. Typical applications include 48 V eMobility battery management, BLDC motor phase-current monitoring, server/AI accelerator hot-swap current telemetry, USB Power Delivery contract current sensing, and solar inverter string monitoring. Compared with isolated current transducers, the INA293-Q1 achieves comparable accuracy at a fraction of the BOM cost and PCB area. When designing with this device, place the shunt resistor as close as possible to the input pins and keep the input traces symmetrical to preserve CMRR. A 0.1 µF supply bypass capacitor placed within 5 mm of the V+ pin is recommended for stable operation across the full -4 V to +110 V common-mode range. This page synthesizes distributor pricing, drop-in alternatives from the INA293-Q1 family and competing high-side current-sense amplifiers, and practical design notes that go beyond the manufacturer datasheet.

RFQ پەیوەندی
INA321EA/2K5 - Micropower RRO Instrumentation Amplifier | Texas Instruments
INA321EA/2K5

INA321EA/2K5 - Micropower RRO Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA321EA/2K5 is a single-supply micropower CMOS instrumentation amplifier with 40 uA typical quiescent current, less than 1 uA shutdown current, and a 500 uV maximum offset specification. It provides rail-to-rail output, 94 dB common-mode rejection, 10 pA bias current, and external-resistor gain control in an 8-pin VSSOP (DGK) package. An instrumentation amplifier is a differential analog amplifier optimized for measuring small signals superimposed on a larger common-mode voltage. The INA321 belongs to the hierarchy of instrumentation amplifiers, differential amplifiers, amplifier ICs, and analog semiconductors. Its differential input stage rejects common-mode interference while amplifying the voltage difference between its input terminals, making it useful for bridge sensors, biomedical instrumentation, and low-voltage current measurement. Key features include a typical operating current of 40 uA, an offset voltage specified by the manufacturer at 500 uV maximum, a common-mode rejection ratio of 94 dB, and an input bias current of 10 pA. The shutdown function reduces quiescent current to below 1 uA. Its rail-to-rail output can approach the positive supply rail to within 0.02 V, while gain is established with external resistors. The high input impedance and low bias current are especially valuable when sensing high-source-impedance sensors. The amplifier uses a CMOS instrumentation-amplifier architecture optimized for low power and single-supply operation. With a gain of 5 V/V, the listed bandwidth is 500 kHz, providing useful bandwidth for slow biomedical signals, industrial bridges, and general-purpose differential measurements. Because the output approaches the positive rail, correct common-mode range and output-swing calculations remain essential when operating near the supply limit. Typical uses include low-power bridge-sensor conditioning, portable medical instrumentation, battery-powered sensor acquisition, current-shunt measurement, and precision analog front ends. The 40 uA operating current supports energy-limited systems, while shutdown supports duty-cycled measurement in which the amplifier remains inactive between readings. The low bias current minimizes disturbance from high-impedance sources. When designing the circuit, place the gain-setting resistors close to the amplifier and verify the complete input and output common-mode range against the actual signal. If the input is unipolar, bias it near mid-supply rather than allowing a negative input excursion. Do not substitute a similarly packaged instrumentation amplifier unless its pin functions, gain architecture, common-mode range, and output-swing behavior have all been checked. This product page combines the manufacturer's device specifications with practical application guidance, package information, pin mapping, sourcing guidance, and a comparison of available same-family choices. These engineering details help shorten component selection while keeping the decision focused on electrical compatibility rather than package name alone.

RFQ پەیوەندی
INA326EA/250 - 1kHz Precision Instrumentation Amplifier | TI
INA326EA/250

INA326EA/250 - 1kHz Precision Instrumentation Amplifier | TI

The Texas Instruments INA326EA/250 is a precision, low-drift CMOS instrumentation amplifier with rail-to-rail input and output operation, 100 µV maximum input offset voltage, 114 dB typical gain bandwidth at 1 kHz, and 33 nV/√Hz typical input noise. The device is supplied in an 8-pin VSSOP (DGK) package and operates from 2.7 V to 5.5 V. An instrumentation amplifier is a specialized analog amplifier optimized for measuring small differential signals while rejecting common-mode interference. Its internal architecture provides gain, differential sensing, and input common-mode rejection in one device. Within the broader hierarchy, an instrumentation amplifier is an amplifier IC and a precision signal-conditioning component used ahead of converters, sensors, and data-acquisition systems. The INA326 family is designed for systems requiring low drift, low noise, and rail-to-rail signal-chain flexibility. Key characteristics include one amplifier channel, a 0.1 V/V to 1000 V/V programmable gain range, rail-to-rail inputs and outputs, a 2.7 V to 5.5 V supply range, and operation from -40 °C to 85 °C. The combination of 100 µV maximum input offset and 33 nV/√Hz typical noise supports accurate extraction of low-level differential signals. The 1 kHz gain-bandwidth characteristic makes the device suitable for precision rather than high-speed signal acquisition. The INA326EA/250 uses a CMOS implementation to combine low input bias current, low offset voltage, and low drift with rail-to-rail input and output behavior. Because its output can approach the supply rails, downstream circuitry can use a wide portion of the available analog voltage range. Its programmable gain allows one device family to serve applications ranging from modest differential amplification to high-gain sensor conditioning while preserving the same 8-pin footprint. Typical uses include bridge and strain-gauge signal conditioning, low-level current measurement, precision sensor interfaces, medical instrumentation, industrial process measurement, and data-acquisition front ends. The device is particularly appropriate when the target signal is differential, the common-mode environment is demanding, and measurement accuracy matters more than wideband throughput. A suitable analog-to-digital converter can then digitize the conditioned output. A key design consideration is to preserve the differential nature of the input signal. Keep input routing compact, use symmetric interconnections where practical, and place the gain-setting resistor close to the RG pin. Follow the Texas Instruments datasheet pin-description table when assigning PCB tracks, and confirm that the selected gain, supply voltage, and output-swing requirements remain compatible with the intended sensor. This page consolidates the Texas Instruments product characteristics, ordering information, package details, technical comparisons, and application guidance for engineers evaluating the INA326EA/250. It also organizes drop-in ordering options, practical design considerations, and search-focused technical information into one engineering reference.

RFQ پەیوەندی
INA327EA/250 - Precision Rail-to-Rail INA | Texas Instruments
INA327EA/250

INA327EA/250 - Precision Rail-to-Rail INA | Texas Instruments

Texas Instruments INA327EA/250 is a precision, low-drift CMOS instrumentation amplifier with rail-to-rail input and output, shutdown support, a 1 kHz gain-bandwidth product, and a 10-pin VSSOP (DGS) package. It operates from 2.7 V to 5.5 V and is designed for low-side current sensing, sensor conditioning, and measurement systems requiring accurate differential amplification with minimal drift. An instrumentation amplifier is a specialized amplifier that combines differential input sensing, high input impedance, precise gain setting, and common-mode rejection in one package. This functional category belongs to the amplifier IC hierarchy, where precision instrumentation amplifiers outperform general-purpose operational amplifiers in applications that must measure small differential signals while rejecting large common-mode voltages. The INA327 provides a 1 kHz gain-bandwidth product, rail-to-rail input and output operation, an input bias current of 200 pA, and a common-mode input range that extends beyond the positive and negative supply rails. Its true single-supply architecture supports operation from a single 2.7 V to 5.5 V supply, while low DC errors and low drift suit precision measurement equipment. The INA327EA/250 uses an external resistor network to establish gain, allowing the amplifier to be adapted to different sensor scales without changing the integrated circuit. Its CMOS input stage supports low input bias current and broad common-mode range, although the relatively narrow 1 kHz bandwidth makes it more appropriate for current, temperature, pressure, and slowly varying sensor signals than for wideband signal chains. Typical applications include shunt-based current measurement in power-conversion systems, low-side motor and solenoid monitoring, bridge-sensor signal conditioning, battery current sensing, and precision industrial instrumentation. The shutdown function can reduce supply demand when the measurement channel is not active, while the 10-pin VSSOP package supports compact surface-mount layouts. The principal design consideration is input filtering. Gain-setting resistors and the instrument-amplifier inputs should be positioned close to the device, with differential and common-mode filtering selected carefully to preserve differential accuracy and common-mode rejection. The power rails must remain within the 2.7 V to 5.5 V operating limits, and unused inputs should be connected according to the manufacturer pin-description table. This page combines manufacturer ordering information, package and operating details, drop-in alternatives, application guidance, PCB considerations, and a parameter-by-parameter comparison to support faster component selection and implementation.

RFQ پەیوەندی
INA331IDGKR - 25 V/V Rail-to-Rail Instrumentation Amp | TI
INA331IDGKR

INA331IDGKR - 25 V/V Rail-to-Rail Instrumentation Amp | TI

The Texas Instruments INA331IDGKR is a low-power, single-supply CMOS instrumentation amplifier with a closed-loop gain of 25 V/V, 2.0 MHz bandwidth, and 5 V/us slew rate, housed in an 8-pin VSSOP (DGK) package. It is designed for low-cost, high-gain accuracy with gain set by external resistors, 0.02% gain accuracy, and a 2 ppm/°C temperature coefficient. Additional headline specifications include ±250 µV offset voltage, 90 dB CMRR, and rail-to-rail operation. An instrumentation amplifier is a differential-input analog signal-conditioning IC that amplifies the voltage difference between two sensors while rejecting common-mode interference. The INA331 belongs to the hierarchy of instrumentation amplifier, differential amplifier, analog amplifier, and amplifier IC. It is used where a small sensor differential must be measured accurately in the presence of larger common-mode voltages, particularly in battery-powered industrial, medical, and portable systems. Key features include gain accuracy of 0.02% and a gain temperature coefficient of 2 ppm/°C for gains above 5 V/V. The device has an input offset voltage of ±250 µV, low input bias current, 90 dB CMRR, and a 2.0 MHz bandwidth. Its 5 V/us slew rate supports faster signal transitions, while single-supply and rail-to-rail operation simplify systems operating from a low-voltage source. The low-power design is suited to portable instrumentation and sensor interfaces. The INA331 uses external gain-setting resistors, allowing the closed-loop gain to be adjusted for the required measurement range without changing the package. At the specified 25 V/V gain, the device combines useful bandwidth for low-frequency sensor measurements with common-mode rejection for noisy industrial environments. The input and output stages operate from a single supply, reducing the number of rails required in portable equipment. Typical applications include low-side current sensing in battery systems, differential pressure and temperature measurement, biomedical instrumentation, portable sensor acquisition, industrial bridge excitation, and precision current measurement. The INA331 is especially appropriate when the sensor output is small, the required gain is above 5 V/V, and system power consumption must remain low. When implementing the circuit, place the gain-setting resistors close to the gain inputs and keep the input differential loop area small to minimize noise pickup. Check the common-mode input range at the selected supply voltage and gain because the amplifier must remain within its valid operating region. Decoupling capacitors should be positioned close to the supply pins, with the layout verified against the manufacturer reference layout. This page combines the exact orderable part information, package characteristics, gain and common-mode performance, application guidance, replacement analysis, and PCB considerations needed to evaluate INA331IDGKR before implementation.

RFQ پەیوەندی
INA333AIDGKR - 50uA Zero-Drift INA | Texas Instruments
INA333AIDGKR

INA333AIDGKR - 50uA Zero-Drift INA | Texas Instruments

The Texas Instruments INA333AIDGKR is a low-power, precision, zero-drift instrumentation amplifier with a 1.8 V to 5.5 V supply range, 10 uV typical input offset voltage, 150 kHz bandwidth, and an 8-pin VSSOP (DGK) package. It uses a three-operational-amplifier architecture and one external gain-setting resistor to provide gains from 1 to 1000. An instrumentation amplifier is a differential analog amplifier optimized for measuring small voltage signals superimposed on larger common-mode voltages. Its internal three-op-amp topology provides high input impedance and accurate differential gain, making it more practical than a discrete difference amplifier when source impedances are unequal or signals arrive from sensors. INA333 belongs to the precision amplifier hierarchy: instrumentation amplifier, operational amplifier, analog IC, and semiconductor. The INA333 emphasizes low power, low offset drift, and rail-to-rail output operation. Verified source data identifies a 50 uA typical supply current and a gain equation of G = 1 + 100 kΩ/RG. The 150 kHz bandwidth supports fast sensor signals, while the 10 uV input offset specification improves measurement resolution around the zero-input condition. Its input stage is designed to reject common-mode variation encountered in bridge, current-sense, and portable sensing systems. The zero-drift architecture reduces temperature-related offset movement, helping preserve measurement stability when the sensor signal is small relative to input offset. Rail-to-rail output increases usable output swing on low-voltage supplies, although engineers must still verify input common-mode range, output swing, bandwidth, and input bias behavior across the complete intended voltage and temperature range using the manufacturer datasheet. Typical uses include portable medical monitoring, battery-powered industrial instrumentation, pressure and load-cell signal conditioning, low-side current measurement, and low-voltage sensor acquisition. The 50 uA power budget is especially useful for wearable and remote systems where every microamp affects battery life. The VSSOP-8 package supports compact layouts, but differential routing and gain-resistor placement remain essential. For best results, connect the gain resistor close to the RG pins, use a low-noise reference supply, maintain symmetric input routing, and follow the datasheet bypass recommendations. Verify common-mode limits at every operating point rather than assuming rail-to-rail input. This page combines verified distributor data, manufacturer specifications, sourcing guidance, and practical design context.

RFQ پەیوەندی
INA333SHKQ - Zero-Drift Instrumentation Amplifier | Texas Instruments
INA333SHKQ

INA333SHKQ - Zero-Drift Instrumentation Amplifier | Texas Instruments

Texas Instruments INA333SHKQ is a micro-power, zero-drift, rail-to-rail output instrumentation amplifier with a closed-loop gain range of 100 to 1000 V/V. It is offered in an 8-pin HKQ ceramic flat package and is rated for operation from -55°C to +210°C. The high-temperature grade makes the device suitable for precision sensing systems that require stable amplification under extended thermal exposure. An instrumentation amplifier is a specialized analog amplifier optimized for measuring small differential signals while rejecting common-mode interference. Its internal differential architecture preserves signal integrity when the inputs share substantial common-mode voltage. Within the broader semiconductor hierarchy, an instrumentation amplifier belongs to the amplifier IC family and combines precision input, gain-setting, and differential-to-single-ended conversion functions in one device. The INA333SHKQ supports closed-loop gains from 100 to 1000 V/V. At a gain of 100, the manufacturer lists a maximum input offset voltage of 25 µV, a typical drift of 0.2 µV/°C, and noise density of 55 nV/√Hz. Its listed common-mode rejection is at least 100 dB at a gain of 10. These characteristics make the amplifier suitable for bridge-based sensors where small millivolt-level differential outputs must be measured accurately. The device operates from a single 1.8 V to 3.5 V supply according to the INA333 family specifications. Its rail-to-rail output stage permits the output voltage to approach the supply limits, improving utilization of low-voltage signal chains. A single external resistor sets the gain, simplifying implementation while preserving accurate differential amplification. The micro-power operating current supports battery-operated instrumentation where continuous sensor monitoring is required without excessive load. Typical uses include pressure and force transducers, thermocouple and RTD interfaces, biomedical instrumentation, portable measurement systems, and industrial process-control equipment. The -55°C to +210°C operating range distinguishes the SHKQ grade from the standard commercial INA333 variants and supports use in high-temperature measurement environments. When laying out an INA333SHKQ circuit, route the differential input and gain-resistor connections as short, symmetric traces, and place input filtering close to the source. Check common-mode input limits at the selected supply voltage because the allowable input range is not independent of supply. Confirm output headroom at the required gain and load, especially in low-voltage systems where rail-to-rail output behavior is important. This page combines the high-temperature INA333SHKQ specifications with application guidance, package information, engineering design notes, and a careful drop-in replacement assessment. It is intended to help engineers determine whether the device fits a precision sensing application without overlooking gain, temperature, supply, or PCB-footprint constraints.

RFQ پەیوەندی
INA333SJD - Precision Micro-Power Instrumentation Amplifier | TI
INA333SJD

INA333SJD - Precision Micro-Power Instrumentation Amplifier | TI

Texas Instruments INA333SJD is a low-power, zero-drift, rail-to-rail-output instrumentation amplifier packaged in an 8-pin SOIC-8 (JD) package. Its headline characteristics include a 1.8 V to 5.5 V supply range, 150 kHz gain-bandwidth product, 10 µV offset voltage, and 2 nA input bias current. The device is intended for precision low-level sensor measurements where low offset, low drift, high common-mode rejection, and low input bias current are more important than wide bandwidth. An instrumentation amplifier is a differential-input amplifier designed to amplify a small voltage difference between two inputs while rejecting common-mode voltage. The INA333 belongs to the broader zero-drift amplifier family, combining an instrumentation-amplifier architecture with chopper-stabilized low-offset behavior. A zero-drift amplifier continuously corrects its own offset error, allowing low input-referred offset to remain stable over time and temperature. The INA333SJD supports gains of 1, 10, 100, and 1000 through its RG pin. Manufacturer specifications identify a maximum offset voltage of 25 µV at a gain of 100, offset drift of 0.2 µV/°C at a gain of 1000, input noise of 55 nV/√Hz at a gain of 100, and minimum common-mode rejection of 100 dB at a gain of 10. Its 0.16 V/µs slew rate supports relatively slow sensor signals without requiring a high-speed amplifier. The rail-to-rail output allows the output voltage to approach the supply rails, improving usable signal range in low-voltage systems. Gain is established by a single external resistor on the RG pin, simplifying circuit implementation while keeping the gain-setting component outside the amplifier. The measured gain error also depends on the tolerance and temperature coefficient of that resistor, so precision applications should use a suitable resistor network. Typical uses include bridge-based pressure and strain measurements, low-current sensors, biomedical instrumentation, industrial process monitoring, and portable sensor systems. The device is particularly useful when sensor output is small, common-mode voltage is substantial, and thermal offset variation would otherwise dominate the measurement. The principal design trade-off is bandwidth versus precision: the INA333 prioritizes low offset and low drift, while its 150 kHz gain-bandwidth product is modest compared with general-purpose high-speed amplifiers. Designers should also evaluate the high-temperature variant indicated by the INA333SJD ordering information and verify the complete electrical limits for the intended operating range. This product page consolidates the verified manufacturer and distributor details, identifies the practical benefits of zero-drift operation, and organizes the device's gains, noise, offset, supply, package, and application constraints for faster engineering selection.

RFQ پەیوەندی
INA4180AIPWR-Q1 - Quad 26V Current Sense Amp, 20 V/V | TI
INA4180AIPWR-Q1

INA4180AIPWR-Q1 - Quad 26V Current Sense Amp, 20 V/V | TI

The Texas Instruments INA4180AIPWR-Q1 is an automotive-grade, quad-channel voltage-output current-sense amplifier (current-shunt monitor) in a 14-pin TSSOP (PW) package. It senses voltage drops across current-sense resistors at common-mode voltages from -0.2 V to +26 V, independent of the 1.7 V to 5.5 V supply, with a fixed gain of 20 V/V (A1 version) and 350 kHz bandwidth. A current-sense amplifier is a specialized difference amplifier that measures the small voltage developed across a shunt resistor and converts it into a ground-referenced output signal. Within the power-management IC hierarchy, it sits between the shunt element and an ADC or controller, enabling precise current monitoring for system control and protection in automotive and industrial power rails. Key features include the wide -0.2 V to 26 V common-mode range that survives load-dump and cold-crank conditions without external circuitry, four independent amplifiers in one package that reduce BOM cost and board area in multi-rail designs, rail-to-rail output for maximum ADC dynamic range, and offset voltage as low as [DATA_NEEDED: Vos]. The extended -40C to +125C operating range and AEC-Q100 qualification make it suitable for under-hood and body electronics applications. Architecturally, the INAx180 family integrates a precision matched resistor network that sets the gain (A1 = 20 V/V, A2 = 50 V/V, A3 = 100 V/V, A4 = 200 V/V), eliminating external gain-setting resistors and their matching errors. The zero-crossover-compatible input stage supports sensing on the low side or high side of the rail, and the output is referenced to ground regardless of common-mode voltage. Typical applications include automotive battery current monitoring, 48V and 12V board-net supervision, electric power steering motor current feedback, DC-DC converter current loops, and industrial PLC analog input modules. Cost-optimized designs benefit from the quad-channel integration. Design tip: choose the shunt resistor so the full-scale drop is 10-50 mV to balance accuracy against power dissipation, and use Kelvin (4-wire) connections to the shunt for best precision. Pricing shown as of 2026-08-29.

RFQ پەیوەندی
INA597IDGKT - Precision 2MHz Difference Amplifier | TI
INA597IDGKT

INA597IDGKT - Precision 2MHz Difference Amplifier | TI

The INA597IDGKT is a high-precision, wide-bandwidth difference amplifier from Texas Instruments, designed for cost-sensitive applications requiring accurate differential signal measurement. It integrates a precision operational amplifier with a matched resistor network, achieving a maximum offset voltage of 200 µV and an offset drift of 5 µV/°C. The device operates from a single supply of 4.5 V to 36 V or dual supplies of ±2.25 V to ±18 V, with a bandwidth of 2 MHz and a common-mode rejection ratio (CMRR) of 88 dB. Housed in an 8-pin VSSOP (DGK) package, the INA597IDGKT is suitable for space-constrained designs. A difference amplifier is a type of operational amplifier circuit that amplifies the voltage difference between two inputs while rejecting common-mode voltages. It is a fundamental building block in analog signal processing, often used in current sensing, bridge amplification, and precision measurement systems. The INA597 belongs to the broader category of instrumentation amplifiers, which are specialized for accurate differential signal acquisition in noisy environments. Key features of the INA597IDGKT include its low offset voltage and drift, which ensure accurate measurement over temperature, and its high CMRR of 88 dB, which rejects common-mode noise. The device also offers rail-to-rail output, allowing maximum dynamic range in single-supply applications. Its low power consumption makes it ideal for battery-powered and portable instrumentation. The INA597 uses TI's e-trim™ technology, which provides precision trimming of the internal resistor network to achieve excellent gain accuracy and temperature stability. The integrated resistors are laser-trimmed to maintain tight matching, ensuring consistent performance across the operating temperature range. The device is fully specified for operation from -40°C to +125°C, making it suitable for industrial and automotive environments. Typical applications include motor current sensing, battery management systems, and precision data acquisition. In motor control, the INA597IDGKT can measure the voltage across a shunt resistor to monitor current, providing feedback for closed-loop control. In battery management, it can sense charge/discharge currents with high accuracy. The device's wide supply range and rail-to-rail output also make it suitable for industrial process control and test equipment. When designing with the INA597IDGKT, ensure that the input common-mode voltage remains within the specified range to maintain linearity. The reference pin (REF) allows level shifting of the output, which is useful in single-supply applications where the output must be centered at a specific voltage. Proper PCB layout with short traces and adequate bypassing will optimize performance.

RFQ پەیوەندی
INA790A-Q1 - 110V 75ARMS Ultra-Precise Current Sense Amp | TI
INA790A-Q1

INA790A-Q1 - 110V 75ARMS Ultra-Precise Current Sense Amp | TI

The Texas Instruments INA790A-Q1 is an AEC-Q100 qualified, 110V, 75ARMS integrated-shunt ultra-precision current-sense amplifier with enhanced PWM rejection, housed in a 15-VSON (DEK) 6x6 mm package. It combines a calibrated 400 micro-ohm Kelvin-connected shunt resistor with a zero-drift chopped amplifier, delivering +/-35 ppm/degrees C temperature drift and bidirectional current measurement from -4V to +110V common-mode. What is a current-sense amplifier? A current-sense amplifier is an analog IC that measures the voltage across a shunt resistor placed in series with a load and amplifies the small differential voltage into a ground-referenced output proportional to load current. Current-sense amplifiers sit within the signal-chain hierarchy as follows: current-sense amplifier -> instrumentation amplifier -> analog amplifier -> power management analog IC. INA790A-Q1 belongs to the integrated-shunt subfamily, where the shunt resistor and the gain stage are co-packaged, eliminating PCB layout-induced Kelvin errors and parasitic resistance drift that plague discrete solutions. Key features include a -4V to +110V wide common-mode range that survives load-dump and cold-crank transients in 48V automotive rails, 75ARMS continuous current handling, enhanced PWM rejection that suppresses large dv/dt common-mode steps from switching power stages, 1.3 MHz bandwidth for fast transient response, and a low 35 ppm/degrees C maximum temperature drift enabled by the chopper-stabilized architecture. The integrated 400 micro-ohm shunt eliminates external resistor stocking, drift concerns, and board-space overhead. The INA790A-Q1 uses a zero-drift chopper architecture that modulates the input offset voltage to a higher frequency, samples the modulation envelope, and feeds back to cancel the original offset. This technique virtually eliminates the 1/f noise corner and the offset drift that limit conventional current-sense amplifiers in high-precision DC and slow-varying measurements. Typical applications include 48V automotive BLDC motor phase current sensing, server and telecom hot-swap controller current monitors, industrial solenoid and actuator current feedback, solar inverter string current measurement, and battery management system (BMS) pack-current sensing. The AEC-Q100 Grade 1 qualification and PWM rejection make it specifically tailored to inverter and motor-drive environments. When designing with this device, place the INA790A-Q1 in the Kelvin path as close to the load current shunt as possible. Because the shunt is internal, the only PCB layout concern is keeping high-current traces off the analog ground return. Use the REF pin to level-shift the output for bidirectional sensing into an ADC with a ground-referenced input. This page synthesizes TI datasheet parameters, DigiKey pricing, INA790A vs INA790B comparison, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
INA791B-Q1 - 110V 75A High-Bandwidth Current Sense Amp | Texas Instruments
INA791B-Q1

INA791B-Q1 - 110V 75A High-Bandwidth Current Sense Amp | Texas Instruments

The Texas Instruments INA791B-Q1 is an AEC-Q100-qualified, ultra-precise bidirectional current-sense amplifier with integrated 75A EZShunt technology, supporting a common-mode voltage range of -4V to +110V independent of supply. Housed in a 14-pin DFN (DEK) package measuring approximately 2.5 mm x 3 mm, the B-grade variant offers enhanced precision over the A-grade, including tighter gain error and offset drift specifications optimized for high-accuracy current measurement in automotive and industrial systems. A current-sense amplifier is an analog IC that measures the small differential voltage developed across a shunt resistor carrying a large load current, while rejecting the large common-mode voltage present at the shunt terminals. The category belongs to the instrumentation amplifier family, itself a subclass of operational amplifiers used in measurement and protection subsystems. Current-sense amplifiers sit in the signal chain between the power stage and the MCU/ADC, enabling telemetry, overcurrent protection, and closed-loop control in DC/DC converters, motor drivers, and battery management systems. Key features of the INA791B-Q1 include a wide -4V to +110V common-mode range, high bandwidth for fast transient response, support for 75A RMS continuous current via the integrated EZShunt resistor, and a single 2.7V to 5.5V supply drawing only 3.75 mA maximum quiescent current. The B-grade variant delivers tighter initial accuracy and lower drift than the A-grade, making it well-suited to precision telemetry across the automotive temperature range of -40C to +125C. The architecture combines a precision chopper-stabilized front end with an EZShunt integrated shunt element, eliminating external sense resistors while maintaining high CMRR across the entire common-mode range. The device outputs an analog voltage proportional to load current that can be routed directly to an ADC input for software-based current monitoring, fault detection, and coulomb counting. Typical applications include 48V automotive electrical systems, battery management in HEV/EV powertrains, motor control in body and chassis ECUs, solenoid and actuator monitoring, and industrial high-voltage bus telemetry. The integrated shunt simplifies PCB layout and reduces parasitic inductance that otherwise degrades high-di/dt measurement accuracy. When designing with this part, route the high-current path directly through the integrated EZShunt pins to minimize parasitic resistance, and place a low-ESR decoupling capacitor close to the VS pin. The bidirectional capability means the output polarity indicates current direction, which simplifies charge/discharge monitoring in battery systems.

RFQ پەیوەندی