بەرهەمەکان (3,200+)

AD623ARMZ - 3V-12V Rail-to-Rail Instrumentation Amp | Analog Devices
AD623ARMZ

AD623ARMZ - 3V-12V Rail-to-Rail Instrumentation Amp | Analog Devices

The Analog Devices AD623ARMZ is a single-channel, single-supply instrumentation amplifier that delivers rail-to-rail output swing from a 3 V to 12 V supply, packaged in an 8-lead MSOP (RM-8) surface-mount package. Headline ratings are 800 kHz 3 dB bandwidth at unity gain, 300 mV/us slew rate, and a single-resistor gain programming range of 1 to 1000. An instrumentation amplifier is a differential-input amplifier built around an op-amp core, finished with a matched resistor network. The category hierarchy runs instrumentation amplifier -> differential amplifier -> op-amp stage -> analog signal conditioning IC. Instead of a conventional difference amplifier, an in-amp uses four matched resistors to reject common-mode voltage and convert a small differential sensor signal into a single-ended ground-referenced output. Because the resistors are on the same die and laser-trimmed, the AD623 holds high common-mode rejection even with long sensor wiring. Key features of the AD623ARMZ include true rail-to-rail output swing, single-supply operation down to 3 V, gain set by one external resistor (no dual-resistor divider), an 8-lead industry-standard pinout that is pin compatible with the AD620/AD621/AD823 family, and a REF pin that allows output offsetting and direct connection to an ADC input. Input offset voltage and CMRR are specified at both G = 1 and higher gains, letting designers size the error budget before layout. Technically the AD623 is a classic three-op-amp topology: an input stage with high-impedance differential inputs, a differential-to-single-ended middle stage, and an output buffer that drives the load to ground. Because the output buffer swings to both rails, the part can drive the ADC input directly without a coupling capacitor. The 800 kHz unity-gain bandwidth means the closed-loop bandwidth falls roughly with gain, so at G = 100 the usable bandwidth drops to about 8 kHz, which sets the maximum sensor update rate in bridge and thermocouple designs. Typical applications include load-cell and pressure bridge front ends, medical and industrial sensor signal conditioning, current-shunt measurement in power conversion, and battery or process monitoring on 3.3 V and 5 V rails. For low-voltage systems the 3 V minimum supply is the key advantage over the classic AD620, which expects a wider supply span. When designing with the AD623ARMZ, keep the gain resistor close to the RG pin and place the REF pin bypass network at the same ground reference as the sensor return. Provide an RC filter ahead of the inputs if long cables pick up noise, because common-mode rejection degrades with imbalance above roughly 1 kHz. Note that gain error and CMRR are specified with a common-mode range, so verify the sensor's common-mode voltage stays inside that window.

RFQ پەیوەندی
AD623ARZ - 800 kHz Rail-to-Rail Instrumentation Amp | Analog Devices
AD623ARZ

AD623ARZ - 800 kHz Rail-to-Rail Instrumentation Amp | Analog Devices

The Analog Devices AD623ARZ is a single-circuit, rail-to-rail-output instrumentation amplifier designed for single- or dual-supply operation from 2.7 V to 12 V, with a gain-bandwidth product of 800 kHz and an 8-SOIC package. It accepts low-level differential sensor signals and produces a single-ended output, making it suitable for bridge, biomedical, and industrial measurement systems. An instrumentation amplifier is a specialized amplifier optimized for amplifying a differential voltage while rejecting common-mode interference. In the signal-chain hierarchy, the AD623 belongs to the instrumentation-amplifier family of analog amplifier ICs. Its internal design reduces the need to match external resistors closely, improves common-mode rejection, and simplifies systems in which sensor inputs may vary widely in level. The AD623 supports gains from 1 to 1000 using an external gain-setting resistor. Rail-to-rail output swing maximizes usable output range on low-voltage supplies, while the specified 800 kHz gain-bandwidth product provides useful bandwidth for sensor and industrial measurement signals. Its 8-SOIC package is suitable for conventional surface-mount PCB assembly, while the single amplifier per package supports compact analog front ends. The AD623 can operate from 2.7 V to 12 V according to the manufacturer product page, and its rail-to-rail output architecture allows the output to approach the available supply range under suitable loading. This makes the device appropriate for low-voltage systems where a fixed, non-rail-to-rail amplifier could waste a substantial portion of the signal range. Gain is programmed with one external resistor, simplifying adjustment across different sensor sensitivities. Typical uses include Wheatstone bridge measurement, current-shunt monitoring, battery-cell instrumentation, portable medical equipment, and industrial control modules. In a bridge circuit, the differential input captures the imbalance between two sensor arms while the instrumentation amplifier rejects much of the common-mode voltage. The result is a more compact signal-conditioning path than a discrete three-op-amp implementation. A key design consideration is supply-headroom management: confirm output swing, input common-mode range, and load requirements for the exact gain before finalizing the circuit. Place the gain resistor close to the gain-setting pin and follow the reference circuit shown in the manufacturer datasheet to minimize parasitic sensitivity and preserve the expected performance. This page combines the AD623ARZ electrical identity, package information, pin-compatible family alternatives, application guidance, and engineering design notes to support faster component selection, schematic review, and PCB planning.

RFQ پەیوەندی
AD623ARZ-R7 - Rail-to-Rail In-Amp, 3-12V | Analog Devices
AD623ARZ-R7

AD623ARZ-R7 - Rail-to-Rail In-Amp, 3-12V | Analog Devices

The Analog Devices AD623ARZ-R7 is a single-supply, rail-to-rail output instrumentation amplifier with a 2.7 V to 12 V supply range, 800 kHz bandwidth, and 90 dB minimum CMRR at G = 1, housed in an industry-standard 8-lead SOIC package (3.90 mm width). An instrumentation amplifier (in-amp) is a type of differential amplifier that amplifies the difference between two input signals while rejecting common-mode voltages. Characterized by high input impedance, high common-mode rejection ratio (CMRR), and low offset voltage, in-amps form a specialized subclass within the operational amplifier family and are essential building blocks in analog signal conditioning chains for precision sensing. Key features of the AD623ARZ-R7 include gain programming with a single external resistor via the formula G = 1 + 100 kOhm/RG (unity gain with no external resistor), rail-to-rail output swing, and input common-mode range extending 150 mV below ground on a single supply. It operates from single supplies of 3 V to 12 V or dual supplies of +/-2.5 V to +/-6 V, suiting both portable and industrial systems. Technically, the AD623 uses a classic three-op-amp topology with a laser-trimmed internal precision resistor network. The input stage provides high impedance and excellent CMRR, while the output stage delivers rail-to-rail swing. The REF terminal allows low-impedance level shifting of the output, critical for centering signals in single-supply data acquisition systems. A and B grades differ in offset voltage and drift specifications. Typical applications include load cell and pressure sensor signal conditioning, medical ECG front ends, thermocouple amplification, and industrial process control, where the high CMRR rejects common-mode noise in electrically noisy environments. When designing, place the gain resistor close to the device, bypass each supply pin with 0.1 uF, and drive the REF pin from a low-impedance source to preserve CMRR. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $2.65 پەیوەندی
AD623BN - Low-Cost Rail-to-Rail Instrumentation Amplifier | Analog Devices
AD623BN

AD623BN - Low-Cost Rail-to-Rail Instrumentation Amplifier | Analog Devices

Analog Devices AD623BN is a low-cost, single-channel instrumentation amplifier with rail-to-rail output swing, designed for measuring small differential signals while rejecting common-mode interference. It operates from single or dual supplies between 2.7 V and 12 V and accepts a single external resistor for gain programming. The device is packaged in an 8-pin PDIP package and is identified by the manufacturer as a single-supply, rail-to-rail instrumentation amplifier. An instrumentation amplifier is a specialized analog IC that amplifies the voltage difference between two inputs while providing high common-mode rejection. Its internal signal path rejects interference shared by both inputs, making it more effective than a conventional operational amplifier when sensors, bridges, and measurement nodes are exposed to common-mode voltage. The AD623BN belongs to the instrumentation-amplifier hierarchy within analog signal-chain and amplifier ICs. The AD623BN's rail-to-rail output allows the output signal to approach the supply limits, improving dynamic range in low-voltage systems. Its gain can be set with one external resistor, simplifying circuit construction compared with implementations requiring a complete feedback network. The verified product listing identifies a maximum offset of 160 uV, input bias current of 17 nA, and bandwidth of 800 kHz. These characteristics make the part relevant to bridge-based sensing and low-level differential measurements. The architecture supports single-supply operation from 2.7 V to 12 V as well as dual-supply operation. In single-supply systems, the reference input defines the output's midpoint, while the rail-to-rail output stage preserves signal swing near the upper and lower rails. Designers should account for output settling time, input common-mode range, gain error, and power-supply rejection when selecting gain and filtering. Typical uses include weighing and force sensing, pressure and strain measurements, current-shunt monitoring, biomedical instrumentation, industrial process control, and sensor interfaces. The 800 kHz bandwidth accommodates higher-bandwidth sensing paths, while the low offset and bias current help preserve accuracy near the measurement floor. Application filtering should remain separate from the instrumentation amplifier's gain selection. For a new PCB, verify every pin function and supply-decoupling arrangement against the manufacturer datasheet. Keep the gain resistor close to the gain-setting pin, provide stable bypass capacitance at the supply pins, and route the differential inputs symmetrically to reduce sensitivity to unequal parasitics. The manufacturer product page and AD623 datasheet are the primary references for electrical limits, gain equations, and recommended application circuits. This page combines the manufacturer's operating characteristics with practical design guidance, packaging details, application context, and same-footprint replacement options. It is intended to help engineers compare the AD623BN against other instrumentation amplifiers without overlooking input bias, offset, bandwidth, supply voltage, or reference-pin differences.

RFQ پەیوەندی
AD623BNZ - Rail-to-Rail Instrumentation Amplifier | Analog Devices
AD623BNZ

AD623BNZ - Rail-to-Rail Instrumentation Amplifier | Analog Devices

The Analog Devices AD623BNZ is a single-supply, rail-to-rail instrumentation amplifier with a 2.7 V to 12 V operating supply, 800 kHz bandwidth, 0.3 V/µs slew rate, and 100 µV maximum input offset voltage specification. The device is offered in an 8-pin PDIP package and is designed for precision signal conditioning when low cost, low power, and single-supply operation are important. An instrumentation amplifier is a differential-input signal-conditioning IC that amplifies the voltage difference between two inputs while providing high input impedance and accurate differential gain. Within the analog signal-chain hierarchy, an instrumentation amplifier combines input-stage behavior, differential amplification, and output buffering in one package. It is commonly used where a small sensor signal must be measured accurately in the presence of common-mode voltage, source impedance, or grounding constraints. The AD623 supports single-supply operation from 2.7 V to 12 V and also supports dual supplies. Its rail-to-rail output allows the output to approach the available supply range, improving utilization of limited power budgets. A user-programmable gain resistor provides gain adjustment, while the 800 kHz bandwidth supports signals extending well above audio frequency. The 0.3 V/µs slew rate provides useful response capability for moderate-bandwidth measurement systems. The integrated three-op-amp architecture supports differential input sensing while maintaining high common-mode rejection when component matching and resistor accuracy are adequate. Gain is established with an external resistor rather than a fixed internal network, allowing the circuit designer to select sensitivity according to sensor output, analog input range, and required resolution. Careful reference-grounding and resistor selection remain essential because gain accuracy and common-mode rejection depend on these external implementation details. Typical uses include bridge-transducer excitation and sensing, biomedical instrumentation, current monitoring, industrial process measurement, sensor interfaces, and portable data-acquisition systems. In a bridge circuit, the AD623 measures differential millivolt-level excitation changes while rejecting much of the common supply voltage. In a current-shunt monitor, it amplifies the voltage generated across the shunt without substantially loading the measured conductor. Design with the 2.7 V to 12 V supply limits in mind, including input and output headroom at the selected supply voltage. Place bypass capacitors close to the supply pins, use a clean ground reference for the measurement system, and verify that source impedance and gain-resistor values do not compromise accuracy. The rail-to-rail output simplifies low-voltage operation but does not eliminate the need to check output swing under load. This page combines the AD623BNZ electrical characteristics, package information, application guidance, comparison parameters, and verified replacement considerations to support faster component evaluation and PCB design.

RFQ پەیوەندی
AD623BRZ - 800 kHz Rail-to-Rail INA | Analog Devices
AD623BRZ

AD623BRZ - 800 kHz Rail-to-Rail INA | Analog Devices

The Analog Devices AD623BRZ is a single-circuit instrumentation amplifier with a 2.7 V to 12 V supply range, rail-to-rail output swing, bandwidth up to 800 kHz, and programmable gain up to 25 in an 8-lead SOIC package. It accepts sensor signals through a differential input while rejecting common-mode noise, making it suitable for precision measurement, industrial sensing, and low-voltage acquisition systems. An instrumentation amplifier is a specialized analog amplifier optimized for measuring small differential signals superimposed on a larger common-mode voltage. Its internal topology combines differential input amplification, high input impedance, and common-mode rejection. The AD623BRZ belongs to the instrumentation-amplifier hierarchy within amplifier ICs and interface ICs, providing a practical alternative to constructing a balanced differential amplifier from several discrete operational amplifiers. The AD623 can operate from single or dual supplies, and its output can swing close to the supply rails. A single external gain-setting resistor programs the closed-loop gain, simplifying designs that require adjustable signal amplification. The device also provides internal gain-set resistors for common gain selections and supports operation with a single external resistor where continuous gain adjustment is useful. Its rail-to-rail output stage improves usable output range in low-voltage systems. With an 800 kHz bandwidth and approximately 0.3 V/µs slew rate, the AD623BRZ can process signals faster than many low-frequency precision instrumentation amplifiers. This bandwidth is especially useful for sensor outputs whose useful content includes pulse, vibration, or other time-varying components. The operating range of 2.7 V to 12 V accommodates battery-powered, industrial, laboratory, and portable measurement equipment without requiring a high-voltage analog supply. Typical applications include bridge-transducer excitation and readout, pressure and strain measurement, biomedical instrumentation, current sensing, industrial process monitoring, and buffered differential sensor interfaces. The 8-lead SOIC package supports conventional surface-mount assembly while exposing input, output, reference, supply, and gain-configuration connections in an industry-standard format. For reliable operation, maintain the supply voltage within 2.7 V to 12 V and ensure that input and output common-mode voltages remain within the device's permitted range. Gain selection requires careful resistance placement to minimize parasitic capacitance and thermal noise. Decoupling capacitors should be positioned close to the supply pins, while sensitive input routing should minimize pickup and board contamination. This page combines the Analog Devices product information, package and sourcing details, strict drop-in alternatives, and practical application guidance to support component selection and PCB implementation. It also highlights verified differences among the AD623BRZ and related AD623 orderable part numbers so engineers can assess replacement risk before modifying a production design.

RFQ پەیوەندی
AD624AD/+ - Precision Instrumentation Amplifier | Analog Devices
AD624AD/+

AD624AD/+ - Precision Instrumentation Amplifier | Analog Devices

The Analog Devices AD624AD/+ is a high-precision, low-noise instrumentation amplifier for low-level transducer signals, with programmable gains of 1, 100, 200, 500, and 1000, a 25 MHz gain-bandwidth product, a 5 V/µs slew rate, and a 15 µs settling time in a 16-lead ceramic DIP package. Designed around load cells, strain gauges, and pressure transducers, it combines high gain accuracy with low noise and strong common-mode rejection for sensitive measurement systems. An instrumentation amplifier is a differential amplifier optimized for amplifying small voltage differences superimposed on larger common-mode voltages. Within the signal-chain hierarchy, it sits between the transducer and the analog signal-conditioning stage, providing differential input, high input impedance, stable closed-loop gain, and accurate gain-setting behavior. This makes the AD624AD/+ useful when the source resistance can vary or when a conventional difference amplifier would not provide sufficient common-mode rejection. The AD624 achieves trimmed gains without external components at gain selections of 1, 100, 200, 500, and 1000. Its low-noise behavior, gain temperature coefficient of 5 ppm maximum at gain 1, input offset-voltage drift of 0.25 µV/°C maximum, and CMRR of 130 dB minimum at DC to 1000 Hz support accurate bridge measurements. Maximum nonlinearity is 0.001% at gain 200, helping preserve measurement integrity across the usable signal range. For high-speed data-acquisition systems, the 25 MHz gain-bandwidth product permits signal amplification without sacrificing required bandwidth. The 5 V/µs slew rate supports rapid output transitions, while the 15 µs settling time defines useful settling behavior after a step input. These characteristics complement the precision dc specifications and make the amplifier suitable for both slow transducer measurements and higher-speed instrumentation. Typical uses include load-cell weighing systems, strain-gauge bridges, pressure transducers, biomedical instrumentation, industrial process monitoring, and precision data-acquisition front ends. In a bridge circuit, the small differential output is amplified while common-mode excitation and environmental disturbances are rejected. The gain-selection network and the sensor bridge determine the usable sensitivity and should be evaluated together for offset, noise, saturation, and calibration requirements. Designers should verify the complete AD624AD/+ pin assignment against the manufacturer datasheet before assigning PCB tracks. Supply bypassing, input grounding, bridge excitation return paths, and output settling time directly affect accuracy. Because the 16-lead ceramic DIP package is not represented by a pin-specific package diagram in the package library, use the manufacturer pin-description table for layout and inspection work. This product page combines the manufacturer’s electrical characteristics with application guidance, drop-in-family comparisons, and practical design notes. It also distinguishes the AD624AD/+ from temperature-grade and package-code variants, helping engineers confirm ordering identity and PCB compatibility before committing a design to production.

RFQ پەیوەندی
AD624ADZ - Precision Instrumentation Amplifier, 25MHz | Analog Devices
AD624ADZ

AD624ADZ - Precision Instrumentation Amplifier, 25MHz | Analog Devices

The Analog Devices AD624ADZ is a high precision, low noise instrumentation amplifier with a 25 MHz gain bandwidth product, 5 V/us slew rate and 200 uV maximum input offset voltage, housed in a 16-pin CDIP (0.300 inch, 7.62 mm) package operating from +/-6 V to +/-18 V supplies. An instrumentation amplifier is a specialized differential amplifier designed to amplify the difference between two input signals while rejecting common-mode voltage. Within the signal chain hierarchy, it sits between the transducer and the ADC, combining multiple internally matched op-amp stages so that gain is set by a single resistor (or internal trims) rather than four matched resistors. This architecture delivers the high common-mode rejection, high input impedance and precise gain accuracy that general-purpose op-amps cannot achieve in bridge and transducer front ends. Key features of the AD624 include factory-trimmed gains of 1, 100, 200, 500 and 1000 with no external components, low noise and high linearity, and a 15 us settling time that supports high speed data acquisition. The combination of low noise, high gain accuracy and low gain temperature coefficient makes it suitable for microvolt-level signals. Architecturally, the AD624 uses a classic three-op-amp instrumentation topology with laser-trimmed input stages. The 25 MHz gain bandwidth product preserves signal fidelity even at moderate gains, while the 5 V/us slew rate prevents slewing-induced distortion on fast transducer outputs. Typical applications include load cell and strain gauge bridge amplification, pressure transducer signal conditioning, and high speed multi-channel data acquisition systems where low offset and fast settling are both required. A key design consideration: the 16-CDIP package is through-hole, so PCB footprint, assembly process and thermal environment must be planned around a DIP-style component; gains other than the factory trims require an external gain resistor whose value and drift directly affect accuracy. This page synthesizes distributor stock data, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, giving sourcing and design engineers a single quotable reference.

RFQ پەیوەندی
AD624BDZ - 25 MHz Low-Noise Instrumentation Amplifier | Analog Devices
AD624BDZ

AD624BDZ - 25 MHz Low-Noise Instrumentation Amplifier | Analog Devices

The Analog Devices AD624BDZ is a high-precision, low-noise instrumentation amplifier designed for low-level transducer and sensor signal conditioning. It provides a 25 MHz gain-bandwidth product, 5 V/µs slew rate, and 15 µs settling time for high-speed data-acquisition applications. The AD624BDZ is supplied in a 16-lead ceramic DIP package and supports internal trimmed gains of 1, 100, 200, 500, and 1000 without external gain-setting components. Its specified input offset voltage is 75 µV, and the operating supply range is ±6 V to ±18 V. An instrumentation amplifier is a precision analog signal-conditioning device built to amplify small differential sensor signals while rejecting common-mode noise and interference. The AD624 family is commonly used with load cells, strain gauges, and pressure transducers because it combines differential input handling, high gain accuracy, low noise, and fast settling performance in one integrated circuit. In a typical measurement chain, the sensor converts a physical quantity into a small differential voltage, the AD624BDZ amplifies that voltage, and a downstream ADC or data-acquisition system performs digitization. The AD624 offers several features suited to precision measurement systems. Its internal trimmed gain options eliminate the need for precision external feedback resistors for common gain settings, while its high bandwidth supports faster acquisition cycles than a conventional slow instrumentation amplifier. The 5 V/µs slew rate helps preserve signal fidelity during large transient responses, and the 15 µs settling time allows the amplifier output to stabilize rapidly between measurements. Low noise makes the device suitable for sensors whose useful signal amplitude is close to the measurement system’s noise floor. The AD624BDZ uses a three-op-amp instrumentation-amplifier architecture to provide high input impedance and accurate differential gain. Its internal resistors and trim circuitry establish accurate gain without requiring external calibration resistors for the predefined gains. The device is intended for systems operating from dual positive and negative supplies, allowing bipolar sensor signals to remain centered around ground. The manufacturer identifies the AD624 as a precision, low-noise instrumentation amplifier with strong DC and AC performance. Typical applications include industrial load-cell measurement, strain-gauge bridges, pressure-transducer interfaces, laboratory instrumentation, biomedical signal acquisition, and high-speed data-acquisition systems. The 16-lead ceramic-DIP package makes it suitable for equipment requiring a through-hole component and a conventional industrial or laboratory instrumentation architecture. When using the AD624BDZ, confirm the supply voltage, gain configuration, input common-mode range, and output swing against the sensor and ADC interface. Place the device close to the transducer to minimize interference pickup on high-impedance sensor lines, and use suitable bypassing capacitors around the power pins. The ceramic DIP package also requires attention to socket or PCB through-hole alignment and thermal management during system assembly. This page combines manufacturer specifications, package information, pricing references, and practical selection guidance for engineers evaluating the AD624BDZ in precision sensor-conditioning and data-acquisition designs.

RFQ پەیوەندی
AD624CDZ - 25 MHz Precision Instrumentation Amplifier | Analog Devices
AD624CDZ

AD624CDZ - 25 MHz Precision Instrumentation Amplifier | Analog Devices

The Analog Devices AD624CDZ is a single-channel, high-precision instrumentation amplifier with a 25 MHz gain-bandwidth product, 5 V/us slew rate, and 15 us settling time, packaged in a 16-lead ceramic DIP. It is designed for low-level transducer signals where accurate gain, low noise, and fast settling are more important than absolute size. Internal trim resistors establish accurate gains of 1, 100, 200, 500, and 1000 without external components, while the internal gain-set resistor remains accessible for other gain values. An instrumentation amplifier is a specialized amplifier category optimized for differential signals originating from sensors such as load cells, strain gauges, and pressure transducers. Its internal three-amplifier architecture provides high input impedance, common-mode rejection, and precise gain setting without requiring matched external resistors. Within the signal-chain hierarchy, an instrumentation amplifier belongs to the amplifier family and ultimately to the broader category of analog signal-conditioning integrated circuits. The AD624CDZ combines a 25 MHz gain-bandwidth product with internal trim networks for gains of 1, 100, 200, 500, and 1000. The manufacturer identifies the device as a high-precision, low-noise instrumentation amplifier with an outstanding combination of noise performance, gain accuracy, low gain temperature coefficient, and linearity. These characteristics support high-resolution data-acquisition systems in which the transducer output is small and the useful signal occupies only a small portion of the amplifier's full-scale capability. Fast analog performance makes the AD624 useful beyond slow process-control loops. The 5 V/us slew rate allows large input steps to be followed without excessive settling delay, and the 15 us settling specification supports high-speed measurement systems. Because the AD624 uses internal trim resistors, its factory-calibrated gain behavior avoids the resistor-matching errors that normally appear in discrete instrumentation-amplifier implementations. Users can still select intermediate gains with an external resistor placed across the gain-set terminals. Typical applications include load-cell and strain-gauge measurement bridges, industrial pressure transducers, high-resolution data acquisition, medical instrumentation, and instrumentation-amplifier input stages for precision converters. The 16-lead ceramic DIP package supports conventional through-hole assembly and is appropriate where long service life and temperature stability are more important than surface-mount area reduction. When laying out the circuit, place the AD624 close to the sensor bridge and route the differential sensor inputs as a short, symmetric pair to minimize pickup from switching nodes. Avoid long parallel runs beneath high-current or high-voltage traces, and use a shield or guard strategy when the transducer leads are long. Verify the input common-mode range, supply voltage, output swing, and gain-set resistor value against the manufacturer datasheet before finalizing the circuit. This page combines manufacturer performance data, package information, application engineering guidance, and a structured comparison of compatible AD624 family members. It is intended to help engineers select a suitable gain setting, plan the layout, and evaluate replacement options without relying on a distributor summary alone.

RFQ پەیوەندی
AD625AD - Programmable Gain Instrumentation Amplifier | Analog Devices
AD625AD

AD625AD - Programmable Gain Instrumentation Amplifier | Analog Devices

Analog Devices AD625AD is a precision programmable-gain instrumentation amplifier with user-programmed gains from 1 to 10,000, a 25 MHz gain-bandwidth product, and low-noise performance of 4 nV/√Hz at 1 kHz. The device is packaged in a 16-lead ceramic dual inline package identified as 16-CDIP, providing a durable through-hole format for precision signal-conditioning equipment. An instrumentation amplifier is a specialized amplifier category designed to amplify small differential signals while rejecting common-mode interference. Its internal topology and external gain resistor make it particularly useful when input impedance, gain accuracy, and common-mode rejection must be maintained simultaneously. In the signal-chain hierarchy, the AD625AD belongs to the precision instrumentation-amplifier family within amplifier ICs and analog signal-conditioning components. Key characteristics include a maximum low-gain error of 0.02%, maximum low-gain temperature coefficient of 5 ppm/°C, maximum low nonlinearity of 0.001%, and a maximum offset voltage of 200 µV. The 25 MHz gain-bandwidth product allows the closed-loop bandwidth to decrease as gain increases, making the amplifier suitable for both precision measurement and higher-frequency sensor interfaces. The AD625AD uses an external gain-setting resistor to establish its programmed gain. Designers must calculate the required resistance from the device's gain equation and verify resistor tolerance, temperature coefficient, parasitics, and stability across the intended signal bandwidth. Its 4 nV/√Hz noise characteristic is particularly relevant when resolving low-amplitude transducer outputs without allowing amplifier noise to dominate the measurement. Typical applications include bridge and strain-gage signal conditioning, biomedical instrumentation, laboratory measurement systems, precision current measurement, and industrial sensor interfaces. The 16-CDIP package is useful where a through-hole assembly and long service life are preferred over a surface-mount footprint, although the larger board area and through-hole thermal behavior must be considered in compact systems. The primary design trade-off is bandwidth versus gain. The 25 MHz gain-bandwidth product supports a range of measurement speeds, but useful closed-loop bandwidth falls as the selected gain rises. Layout should therefore use short signal paths, a clean analog ground reference, and an external gain resistor positioned close to the gain-setting pin. This page combines manufacturer specifications, lifecycle guidance, practical circuit-design considerations, sourcing information, and verified drop-in alternatives to support faster component evaluation and board-level planning.

RFQ پەیوەندی
AD625ADZ - 25MHz Programmable Gain Amplifier | Analog Devices
AD625ADZ

AD625ADZ - 25MHz Programmable Gain Amplifier | Analog Devices

The Analog Devices AD625ADZ is a precision programmable-gain instrumentation amplifier with user-programmed gains up to 10,000, a 25 MHz gain-bandwidth product, 5 V/µs slew rate, and a 16-CDIP package. It supports low-noise differential measurement with 4 nV/√Hz input noise at 1 kHz, maximum gain error of 0.02%, and maximum low nonlinearity of 0.001%. The device is packaged in a 0.300-inch, 7.62 mm-wide 16-pin ceramic dual in-line package. An instrumentation amplifier is a precision analog signal-conditioning amplifier optimized for measuring small differential signals superimposed on a large common-mode voltage. Its internal topology amplifies the difference between two inputs while rejecting common-mode noise. In the broader component hierarchy, the AD625 belongs to instrumentation amplifiers, a specialized class of amplifier ICs used in sensor measurement, data acquisition, medical instrumentation, and industrial control systems. Programmable gain is the AD625ADZ's defining feature. The manufacturer identifies gains of 1 through 10,000 as user programmable, supporting both conventional resistor-selected gain and software-controlled measurement systems. A maximum gain error of 0.02% and gain temperature coefficient of 5 ppm/°C support repeatable scaling across changing temperatures. The specified 25 MHz gain-bandwidth product and 5 V/µs slew rate provide bandwidth for dynamically changing measurement signals rather than only static voltages. The AD625's low-noise and precision characteristics make it suitable for demanding front ends. The published input-noise figure is 4 nV/√Hz at 1 kHz, while the listed low nonlinearity of 0.001% helps limit distortion when large differential signals are amplified. Its instrumentation-amplifier architecture supports bridge, current-loop, and other differential sensing arrangements where input bias current, offset, common-mode rejection, and gain accuracy can affect measurement quality. Typical uses include weighing systems based on load cells, precision pressure and strain-gauge bridges, biomedical instrumentation, industrial process monitoring, and high-resolution data-acquisition channels. The ability to select a gain close to the full-scale differential input can improve use of the downstream converter's input range and reduce demands on its analog signal chain. Digital control of gain is also useful when measurements span several magnitudes. A critical design consideration is gain implementation around the instrumentation amplifier. Follow the manufacturer's gain-setting table and observe the specified resistor values and tolerances because gain accuracy depends on both the amplifier and the external network. Provide adequate bypassing at the supply pins, maintain a common ground reference, and verify input and output voltage limits against the selected gain before connecting sensors or converters. This product record combines the manufacturer's product information with pin-compatible family options and practical design guidance. It helps engineers distinguish the ceramic-DIP AD625ADZ from other AD625 package and temperature-grade variants while supporting component selection, schematic planning, and signal-chain design for precision measurement systems.

RFQ پەیوەندی
AD625BD/+ - Programmable Gain Instrumentation Amplifier | Analog Devices
AD625BD/+

AD625BD/+ - Programmable Gain Instrumentation Amplifier | Analog Devices

The Analog Devices AD625BD/+ is a precision programmable-gain instrumentation amplifier in a 16-lead ceramic dual in-line package. It is intended for systems that require nonstandard signal gains and precision amplifier implementations controlled by external resistance. The manufacturer identifies the AD625 family as a one-circuit instrumentation amplifier designed around a programmable-gain architecture, providing a practical option when a conventional fixed-gain amplifier cannot implement the required gain range. An instrumentation amplifier is a differential analog signal-conditioning IC built to amplify the voltage difference between two inputs while rejecting common-mode interference. In the broader semiconductor hierarchy, the AD625 belongs to the precision amplifier family, then analog amplifiers, then integrated circuits used for measurement and sensor-conditioning systems. This makes it relevant to bridge, strain-gauge, biomedical, industrial, and laboratory instrumentation designs where accurate differential measurement is more important than minimum component count. The AD625 supports programmable gain, allowing the system designer to select amplification according to the sensor output and measurement range. Compared with fixed-gain amplifiers, this architecture is useful when the signal amplitude changes substantially or when multiple gain settings are required in the same design. The AD625BD/+ is identified as the ceramic 16-CDIP orderable variant, while the related AD625 family also includes variants intended for lower-cost software-oriented instrumentation applications. The differential internal structure supports rejection of common-mode voltage before the final output stage. In practical use, the amplifier operates between differential input signals, an external gain-setting network, suitable bypass or filtering components, and a downstream measurement or conversion stage. The exact input range, gain equation, bandwidth, input impedance, offset, noise, and supply-current limits must be selected from the manufacturer data sheet, Rev. D, according to the exact ordering code and operating conditions. Typical uses include low-level sensor amplification, laboratory measurement front ends, strain-gauge and bridge excitation systems, biomedical instrumentation, and industrial monitoring. The 16-CDIP package favors through-hole assembly in higher-reliability or legacy-style equipment and can simplify repair or replacement where a ceramic package is preferred over a molded plastic package. Designers should verify the AD625BD/+ pinout, maximum supply voltage, input common-mode range, allowable differential input range, gain-setting resistor limits, and stability requirements against the manufacturer data sheet before layout. Check that the selected gain network does not load the inputs, that power-supply bypassing is placed close to the device, and that unused inputs are handled according to the recommended circuit. This page organizes the AD625BD/+ ordering information, programming considerations, application guidance, comparison context, and verified manufacturer references. It also distinguishes lifecycle suitability from electrical equivalence: the AD625 family is marked not recommended for new designs, so engineers should assess availability and design alternatives when starting a new platform.

RFQ پەیوەندی
AD625BDZ - Programmable Gain Instrumentation Amplifier | Analog Devices
AD625BDZ

AD625BDZ - Programmable Gain Instrumentation Amplifier | Analog Devices

Analog Devices AD625BDZ is a precision programmable-gain instrumentation amplifier packaged in a 16-CDIP ceramic dual in-line package. The device is designed for precision signal conditioning applications requiring user-programmed gains up to 10,000, low gain error, and low output noise. The AD625BDZ is identified by Analog Devices as not recommended for new designs, so engineers should evaluate the current product portfolio before beginning a new design. An instrumentation amplifier is a differential-input analog IC that amplifies the voltage difference between two inputs while rejecting common-mode signals. Within the broader hierarchy of amplifier ICs, operational amplifiers and instrumentation amplifiers support precision measurement, sensor conditioning, current sensing, biomedical instrumentation, and industrial control. The AD625 uses internal resistance networks and gain-control circuitry to provide accurate amplification where fixed-gain amplifiers or discrete op-amp stages would require additional parts. Key characteristics include user-programmed gains up to 10,000, maximum low gain error of 0.02%, maximum low nonlinearity of 0.001%, a 25 MHz gain-bandwidth product, and a 5 V/µs slew rate. The input-referred noise is listed as 4 nV/√Hz at 1 kHz. These parameters make the AD625BDZ relevant to applications that need programmable sensitivity while maintaining low signal-level distortion and gain accuracy. The AD625 architecture supports nonstandard gain selections that are not easily realized with conventional fixed-gain devices. Its internal gain network reduces the need for external resistor networks and calibration hardware, while the 25 MHz bandwidth provides signal-rate headroom. Designers must still account for gain-dependent bandwidth, input-referred noise, output swing, and settling behavior when configuring the gain-control interface. Typical uses include bridge-transducer amplification, precision current measurement, laboratory instrumentation, biomedical sensor interfaces, and low-level differential signal acquisition. The 16-CDIP package favors through-hole construction and applications where ceramic DIP mechanical compatibility, serviceability, or long-term board availability is more important than minimal board area. For implementation, follow the manufacturer datasheet for the gain-control logic, reference-voltage arrangement, power-supply sequence, decoupling, and output measurement connection. Because the AD625 is not recommended for new designs, engineers should verify lifecycle status, package availability, and qualification requirements against the current Analog Devices product information before committing a new PCB. This page combines manufacturer lifecycle information, distributor catalog attributes, package and gain details, cross-reference findings, and practical selection guidance. It also distinguishes true package-level replacement candidates from general instrumentation-amplifier alternatives so that obsolete or restricted designs are not migrated without an engineering review.

RFQ پەیوەندی
AD625CD - Programmable Gain Amplifier | Analog Devices
AD625CD

AD625CD - Programmable Gain Amplifier | Analog Devices

Analog Devices AD625CD is a programmable-gain instrumentation amplifier with user-programmed gains from 10 to 10,000, a 25 MHz gain-bandwidth product, 4 nV/√Hz input noise at 1 kHz, and a 16-lead ceramic dual-in-line package. The device is intended for precision signal conditioning where conventional fixed-gain instrumentation amplifiers do not provide the required gain flexibility. An instrumentation amplifier is a differential analog signal-conditioning IC that combines input buffering, differential amplification, and gain-setting circuitry in one package. Its hierarchy includes instrumentation amplifier, analog signal conditioner, analog IC, and semiconductor. This category is particularly useful for amplifying small differential sensor signals while rejecting common-mode noise and voltage applied simultaneously to both inputs. The AD625CD provides a maximum gain error of 0.02%, a maximum gain temperature coefficient of 5 ppm/°C, a maximum nonlinearity of 0.001%, and a maximum offset voltage of 25 µV. These characteristics support accurate measurement systems in which gain drift and signal-chain distortion directly affect result repeatability. The broad 10-to-10,000 gain range covers load-cell, strain-gauge, pressure-transducer, and laboratory measurement interfaces. Its 25 MHz gain-bandwidth product provides useful bandwidth for low-frequency precision measurements and instrumentation. The specified 4 nV/√Hz input noise at 1 kHz helps preserve weak-signal information, while the low gain error and temperature coefficient support stable calibration over changing ambient conditions. The 16-CDIP package is suitable for conventional through-hole assembly where a mechanically robust ceramic package is preferred. Typical uses include bridge-transducer amplification, precision current measurement, laboratory data acquisition, biomedical instrumentation, and industrial monitoring. In a bridge circuit, the AD625CD can amplify the small differential voltage generated by a strain gauge while rejecting ground-level common-mode voltage. In current sensing, its programmable gain allows the output range to be matched to the available analog-to-converter input range. When designing the signal path, place the gain-setting network close to the device and observe the input common-mode and output-swing limits in the manufacturer datasheet. Check the required gain against the 25 MHz gain-bandwidth product so that the closed-loop bandwidth remains appropriate for the measurement bandwidth. This page combines the AD625CD device characteristics, lifecycle status, application guidance, and design considerations into a practical engineering reference for evaluating this programmable instrumentation amplifier.

RFQ پەیوەندی
AD625CDZ - 25 MHz Instrumentation Amplifier | Analog Devices
AD625CDZ

AD625CDZ - 25 MHz Instrumentation Amplifier | Analog Devices

The Analog Devices AD625CDZ is a single-circuit precision instrumentation amplifier in a 16-pin CDIP package, designed for signal conditioning applications that require programmable gain, high common-mode rejection, and low-noise differential measurement. Its listed gain-bandwidth product is 25 MHz, with a -3 dB bandwidth of 650 kHz and a slew rate of 5 V/us. The AD625CDZ operates from a single +5 V supply according to the manufacturer product description. An instrumentation amplifier is a specialized amplifier category used to amplify small differential sensor signals while rejecting large common-mode voltages. In the broader signal-chain hierarchy, an instrumentation amplifier sits between sensors such as strain gauges, bridge transducers, thermocouples, and high-impedance sensing front ends, and the analog-to-digital converter or downstream measurement circuitry. The AD625 series is intended for applications requiring nonstandard gains, precision gain adjustment, and software-controlled measurement systems. The AD625CDZ combines a 25 MHz gain-bandwidth product with programmable gain capability and a 650 kHz small-signal bandwidth. Its input bias current is listed at 10 nA, supporting high-impedance sensor interfaces, while the 5 V/us slew rate helps preserve signal fidelity in multiplexed measurement systems. The device is offered in a 16-CDIP through-hole package, which is useful for legacy laboratory, industrial, and instrumentation equipment where through-hole assembly and serviceability are preferred over a surface-mount land pattern. Compared with ordinary precision op amps, the AD625CDZ provides a matched internal resistor network and integrated gain-setting arrangement, reducing the number of external precision components required in many gain configurations. The low-noise input stage and programmable gain are particularly useful for bridge-based measurement, biomedical instrumentation, current-loop receivers, and laboratory data-acquisition systems. The 650 kHz -3 dB bandwidth makes it suitable for signal bandwidths well below the unity-gain-frequency limit while preserving the flexibility to set different gains in software. Typical applications include weighing systems using load cells, industrial process monitoring, laboratory measurement equipment, and medical or diagnostic instrumentation. In a bridge or strain-gauge circuit, the amplifier converts a small differential excitation error into a level suitable for an ADC while the internal matched network improves rejection of common-mode pickup. In a software-controlled measurement system, programmable gain allows the same amplifier to handle multiple input ranges without redesigning the analog front end. When laying out a board around the AD625CDZ, keep the input and feedback-network routing short and symmetrical, provide stable bypass capacitance at the supply pins, and avoid long unprotected traces adjacent to high-current switching nodes. Because the package is a through-hole CDIP rather than a surface-mount package, verify the 16-pin mechanical drawing and pin numbering against the manufacturer datasheet before fabrication. This page combines manufacturer product information, distributor listings, package details, and design guidance for engineers evaluating the AD625CDZ.

RFQ پەیوەندی
AD625JNZ - Low-Noise Instrumentation Amplifier | Analog Devices
AD625JNZ

AD625JNZ - Low-Noise Instrumentation Amplifier | Analog Devices

The Analog Devices AD625JNZ is a single-channel, programmable-gain precision instrumentation amplifier rated for dual supply voltages up to ±18 V, with 650 kHz bandwidth, 5 V/µs slew rate, and 4 nV/√Hz input noise at 1 kHz. The device is packaged in a 16-pin PDIP package for through-hole instrumentation, measurement, and signal-conditioning systems. An instrumentation amplifier is a precision amplifier optimized for small differential signals superimposed on a much larger common-mode voltage. Its internal architecture combines differential input stages, high common-mode rejection, and user-programmable gain. This makes the AD625JNZ suitable for sensor interfaces, bridge amplifiers, biomedical instrumentation, and industrial measurement equipment where signal integrity and gain accuracy are more important than minimum cost. Programmable gain is set with an external resistor, allowing circuit designers to select gains that are difficult to obtain with conventional fixed-gain amplifiers. The AD625 family is particularly useful when nonstandard gain values, low noise, high common-mode rejection, and low drift are required together. Its 0.02% gain-error figure supports repeatable calibration across programmable operating ranges. The AD625JNZ provides a 3 dB bandwidth of 650 kHz, a slew rate of 5 V/µs, and a 15 µs settling time. Input bias current is 30 nA, while the listed supply current is 3.5 mA. These characteristics balance signal speed with low noise and moderate power consumption, making the device appropriate for precision analog front ends rather than high-speed RF or general-purpose switching applications. Typical uses include weighing systems, laboratory instrumentation, current-loop receivers, strain-gauge and resistance bridge front ends, medical monitoring equipment, and factory test systems. The AD625JNZ is particularly useful when the source impedance is moderately high and the common-mode voltage varies, because differential amplification and common-mode rejection occur inside a dedicated precision device. Designers should follow the manufacturer's pin-description and gain-setting tables when assigning PCB tracks and external components. Input and reference pins require careful routing, the gain resistor must meet the required accuracy and temperature coefficient, and supply bypassing should be placed close to the device. Because the PDIP package is not surface mount, assess vibration, mechanical retention, and available board area before using it in compact or rugged equipment. This page organizes the AD625JNZ electrical characteristics, lifecycle status, pricing structure, application guidance, and verified pin-compatible family options. It also provides design notes for gain selection, reference grounding, signal-chain layout, and thermal planning so engineers can evaluate the amplifier before placing it in a production design.

RFQ پەیوەندی
AD625KNZ - 25MHz Instrumentation Amplifier | Analog Devices
AD625KNZ

AD625KNZ - 25MHz Instrumentation Amplifier | Analog Devices

The Analog Devices AD625KNZ is a single-channel precision instrumentation amplifier with 50 uV input offset voltage, a 5 V/us slew rate, a 25 MHz gain-bandwidth product, and operation from +/-6 V to +/-18 V in a 16-pin PDIP package. It is designed for low-level differential measurement where high common-mode rejection, accurate gain control, and flexible gain settings are required. An instrumentation amplifier is a differential amplifier optimized for amplifying small sensor signals while rejecting large common-mode voltages. In the signal-chain hierarchy, the AD625 belongs to the instrumentation-amplifier class of amplifier ICs, sitting between general-purpose operational amplifiers and application-specific measurement front ends. Its internal differential core simplifies the transition from a bridge, strain gauge, or thermocouple to a downstream ADC. The AD625 supports precision signal conditioning through a user-selectable gain network and is suited to applications that require nonstandard gain values not easily obtained with common resistor-programmed amplifiers. Its 50 uV offset specification supports accurate low-level measurements, while the 5 V/us slew rate enables higher-amplitude output transitions without requiring a substantially faster amplifier. The AD625 operates from dual supplies of +/-6 V through +/-18 V. Differential inputs can therefore accept substantial signal swing relative to the output reference, which is valuable when transducers produce bipolar outputs centered around ground. The 25 MHz gain-bandwidth product defines the high-frequency behavior of the amplifier, while its internal architecture determines the usable bandwidth at each closed-loop gain. Typical uses include bridge and strain-gauge conditioning, biomedical instrumentation, current-loop receivers, laboratory measurement systems, and high-impedance sensor interfaces. The 16-pin PDIP package is suitable for through-hole assembly and prototypes, and the AD625 family provides related package and temperature options for production sourcing. When laying out a circuit, keep the differential input traces short, symmetrical, and away from high-current switching paths. Connect the gain-setting network close to the amplifier, use a stable reference for output-referenced measurements, and follow the manufacturer pinout and reference-circuit guidance before assigning PCB tracks. This page combines manufacturer specifications, package information, cross-reference findings, comparison parameters, and application-specific design guidance to support component selection and PCB implementation for AD625KNZ-based precision measurement circuits.

RFQ پەیوەندی
AD626ANZ - Low-Cost Single-Supply Differential Amp | Analog Devices
AD626ANZ

AD626ANZ - Low-Cost Single-Supply Differential Amp | Analog Devices

The Analog Devices AD626ANZ is a low-cost, true single-supply differential amplifier designed for amplifying and low-pass filtering small differential signals that carry a large common-mode voltage. It operates from a single supply of 2.4 V to 10 V or from dual supplies of ±1.2 V to ±6 V and is packaged in an 8-pin PDIP. The device provides one amplifier circuit with a differential input stage suitable for precision signal-conditioning and measurement systems. A differential amplifier measures the voltage difference between two input nodes while rejecting voltage common to both inputs. Within the broader semiconductor hierarchy, the AD626 is an operational-amplifier-based signal-conditioning IC, then an amplifier, then an analog integrated circuit used within data-acquisition and instrumentation systems. This category is especially useful when a sensor output is much smaller than the voltage shared by both sensor terminals. The AD626ANZ supports a broad 2.4 V to 10 V single-supply operating range, allowing operation from low-voltage systems as well as conventional industrial rails. Its stated input offset voltage is 2.5 mV, its common-mode rejection is 100 dB, and its gain bandwidth product is 100 kHz. These characteristics make it suitable for current-loop measurements, bridge-amplifier interfaces, sensor conditioning, and low-frequency filtering. The input common-mode range extends to approximately 6 times the positive supply minus 1 V, as stated by the manufacturer, allowing the amplifier to process signals above its supply voltage when the circuit polarity and operating conditions permit. This characteristic helps designers handle high-side sensing and current-shunt measurements without first reducing the common-mode voltage through additional active circuitry. Typical applications include precision current measurement, industrial sensor interfaces, low-pass differential filters, medical instrumentation, and data-acquisition front ends. The 8-pin PDIP package is also suitable for through-hole prototyping and designs where a leaded package simplifies inspection and rework. The principal design constraint is signal bandwidth: with a 100 kHz gain bandwidth product, the usable closed-loop bandwidth depends on the configured gain. Higher closed-loop gain reduces bandwidth and should be checked against the required filter response and settling behavior. Input and feedback resistors also determine practical accuracy and noise performance. This page combines manufacturer operating limits, a package-specific drop-in assessment, and practical replacement guidance. It helps engineers distinguish a true pin-compatible replacement from merely similar instrumentation amplifiers that use different packages or gain architectures.

RFQ پەیوەندی
AD626BN - True Single-Supply Differential Amplifier | ADI
AD626BN

AD626BN - True Single-Supply Differential Amplifier | ADI

The Analog Devices AD626BN is a true single-supply differential amplifier designed to amplify small differential signals that coexist with large common-mode voltages. It operates from a single +2.4 V to +10 V supply or from dual ±1.2 V to ±6 V supplies, has a 100 kHz bandwidth, and is offered in an 8-pin PDIP package. Its maximum input offset voltage is 2.5 mV. A differential amplifier is an amplifier that responds to the voltage difference between two inputs while rejecting voltage common to both inputs. Within the amplifier-IC hierarchy, the AD626BN is a difference amplifier rather than a general-purpose operational amplifier. It is particularly useful when a small sensor or measurement signal must be extracted in the presence of a larger common-mode voltage, reducing the risk that the common-mode component will saturate the signal chain. The principal advantages are its low-cost single-supply operation, true differential input stage, and ability to operate from supplies as low as +2.4 V. The single +2.4 V to +10 V range supports low-voltage sensor systems, while the dual-supply option extends operation to ±1.2 V to ±6 V. The 100 kHz bandwidth is suitable for low-frequency differential measurements rather than high-speed signal processing. In a typical circuit, the two input pins receive the sensor signal and its reference or return path. The amplifier produces an output proportional to the difference between those inputs while the internal architecture suppresses much of the common-mode voltage. Gain is established with external feedback resistors, allowing the circuit to be adapted to different input ranges. Supply decoupling and correct resistor placement remain important because input and output noise directly affect the fidelity of the amplified measurement. Typical uses include current-sense and bridge-signal conditioning, instrumentation interfaces, industrial measurement systems, and low-frequency sensor acquisition. The 8-pin PDIP package is also useful for prototypes, educational circuits, and through-hole industrial control boards where a surface-mount footprint would be inconvenient. Dual-supply operation can simplify systems that already provide symmetrical rails and require bipolar input or output signaling. For a new design, verify the input common-mode range at every supply voltage and confirm that output swing remains within the selected supply limits. Check the feedback-resistor values against the required gain, place the bypass capacitor close to the supply pins, and avoid driving capacitive loads unless the resulting stability behavior has been checked. Those precautions are more important than raw bandwidth when extracting a reliable low-level differential measurement. This page combines the manufacturer's functional description with practical design guidance, package and supply details, a structured comparison, and a focused view of compatible replacement options. It is intended to help engineers answer specification, application, sourcing, and replacement questions without relying on basic distributor listings alone.

RFQ پەیوەندی
AD628ARMZ - High Common-Mode Difference Amplifier | Analog Devices
AD628ARMZ

AD628ARMZ - High Common-Mode Difference Amplifier | Analog Devices

Analog Devices AD628ARMZ is a precision difference amplifier for high common-mode voltage sensing, with programmable gain and excellent direct-current performance. It operates as a single-channel amplifier in an 8-lead MSOP package, making it suitable for battery monitoring, power-supply measurement, and conversion of high-voltage signals for single-supply ADCs. A difference amplifier measures the voltage between two input nodes while rejecting signals common to both inputs. The AD628 combines this differential function with a high common-mode operating range, broad common-mode rejection across frequency, and a wideband feedback loop. That feedback architecture helps reduce distortion caused by the input capacitance of delta-sigma ADCs and improves measurement accuracy in high-impedance signal chains. The AD628ARMZ supports programmable gain, allowing the same amplifier to scale small differential signals or reduce high input voltages into an ADC-friendly range. The available data identifies a slew rate of 0.3 V/us, a 600 kHz bandwidth, 75 dB common-mode rejection, 1.5 mV input offset voltage, and 1.5 nA input bias current. These parameters make the device appropriate for precision current and voltage sensing where input offset and bias currents can influence measurement error. The common-mode range and resistor-divider architecture are particularly relevant to power-supply applications. The manufacturer describes the AD628 as suitable for battery chargers and similar equipment in which high voltages must be scaled into standard control voltages or currents. Its wideband feedback loop also supports systems that require accurate acquisition from capacitive sensor or ADC inputs. Typical uses include battery-pack monitoring, charger feedback, industrial power rails, high-side current sensing, precision differential measurement, and signal conditioning for single-supply analog-to-digital converters. The 8-MSOP format supports compact PCB layouts, although careful common-mode range checking is essential because the allowable input range is application-dependent. For a new design, verify supply voltage, input common-mode voltage, gain setting, output swing, and ADC input range before committing to the layout. Keep the differential input route short and symmetric, provide stable reference or gain-setting resistors, and use appropriate input filtering without adding excessive differential capacitance that could reduce phase margin. This page consolidates the manufacturer’s product description, package information, differential-amplifier characteristics, application guidance, and practical replacement considerations to support faster component selection and PCB planning.

RFQ پەیوەندی
AD629ARZ-R7 - ±270V Common-Mode Diff Amp SOIC-8 | ADI
AD629ARZ-R7

AD629ARZ-R7 - ±270V Common-Mode Diff Amp SOIC-8 | ADI

The Analog Devices AD629ARZ-R7 is a precision difference amplifier rated for ±270 V common-mode input voltage in an 8-pin SOIC (R-7 tape & reel) package. It delivers 86 dB minimum DC CMRR, 1 V/V fixed unity gain, and 2.1 V/µs slew rate from a ±2.5 V to ±18 V dual supply. The device is an improved pin-for-pin replacement for the legacy INA117P and INA117KU. A difference amplifier is a specialized op-amp topology that subtracts two input signals and rejects the common-mode voltage present on both inputs. In the broader IC taxonomy it belongs to the instrumentation amplifier family (in-amp -> difference amplifier -> operational amplifier -> analog IC -> semiconductor). The AD629 specifically targets high common-mode industrial environments where signal levels up to ±270 V must be rejected to extract a small differential signal sitting on top of a large DC bus. Key features include ±270 V continuous common-mode range, 86 dB minimum CMRR (DC to 1 kHz), 500 kHz small-signal bandwidth, 2.1 V/µs slew rate, and integrated precision resistor networks that set unity gain without external components. The internal laser-trimmed thin-film resistors achieve 0.03% typical gain accuracy and excellent common-mode rejection over temperature. The AD629 uses a three-op-amp topology with input overvoltage protection through internal resistors and ESD clamps. Its supply current of approximately 1 mA (per amplifier, single gain stage active) keeps self-heating low, while the SOIC-8 (θJA = 155 °C/W) package is rated for -40 °C to +85 °C operation. Typical applications include motor control phase current sensing, 48 V/24 V battery monitoring, shunt-based high-side current measurement, industrial PLC analog front ends, and power inverter feedback. Designers choose it when they need to digitize a small differential signal riding on a high-voltage DC bus. Designers should ground both REF pins (1 and 5) to a low-impedance ground plane and leave pin 8 floating (NC). Using separate ground returns for input signal ground and REF ground degrades CMRR by tens of dB. This page synthesizes distributor pricing, drop-in alternatives, and PCB layout guidance not available from the manufacturer datasheet alone.

RFQ پەیوەندی
AD629BN - ±270V High Common-Mode Difference Amplifier | Analog Devices
AD629BN

AD629BN - ±270V High Common-Mode Difference Amplifier | Analog Devices

The Analog Devices AD629BN is a unity-gain precision difference amplifier designed to measure small differential signals while rejecting common-mode voltages as high as ±270 V. It combines a monolithic precision operational amplifier with an integrated thin-film resistor network in an 8-pin PDIP package. The high common-mode range allows the device to operate in high-voltage industrial systems without requiring external high-voltage attenuation resistors. A difference amplifier is a specialized amplifier IC that amplifies the voltage difference between two inputs while rejecting a voltage common to both inputs. This category sits within amplifier ICs and instrumentation signal-chain devices. It is particularly useful when a sensor, shunt, transducer, or measurement node operates at a high DC voltage but the useful information is represented by a comparatively small differential signal. The AD629BN provides a differential gain of unity. To achieve its high common-mode range, an internal resistor divider attenuates the noninverting input by a factor of 20. Other internal resistors, including the feedback network, restore the overall differential gain to unity. This architecture allows accurate differential measurement without changing the nominal system gain. The manufacturer identifies the AD629 as a production device and describes it as a precision device for measuring differential signals in the presence of common-mode voltages up to ±270 V. Its integrated resistor network simplifies the external circuit compared with a discrete difference-amplifier implementation. The eight-pin PDIP package also supports conventional through-hole assembly and prototype rework. Typical uses include power-converter feedback monitoring, motor-drive bus measurement, industrial control sensing, battery-system instrumentation, and high-voltage test equipment. In these applications, the AD629BN can reject the large common-mode voltage while preserving a differential voltage measurement suitable for an ADC, comparator, control loop, or diagnostic circuit. A key design consideration is that the input common-mode voltage must remain within the device's specified operating range under all transient and fault conditions. Designers should also verify the allowed differential input range, supply requirements, output swing, bandwidth, and gain error against their exact operating conditions using the manufacturer datasheet before finalizing the circuit. This product page combines the AD629 architecture, operating-range details, package information, replacement guidance, and application-focused design notes to support faster component selection, PCB planning, and precision signal-chain design.

RFQ پەیوەندی
AD632SH/883B - Precision 4-Quadrant Multiplier | Analog Devices
AD632SH/883B

AD632SH/883B - Precision 4-Quadrant Multiplier | Analog Devices

The AD632SH/883B is an internally trimmed precision monolithic four-quadrant analog multiplier/divider from Analog Devices, packaged in a hermetic TO-100-10 metal can. It is pin-for-pin compatible with the industry-standard AD532 but offers improved specifications, including a fully differential high-impedance Z-input. The device can provide gains up to ×10, often eliminating the need for separate instrumentation amplifiers to precondition inputs. It operates over the military temperature range of -55°C to +125°C and is available in a through-hole TO-100-10 package. An analog multiplier is a circuit that produces an output voltage proportional to the product of two input voltages. The AD632 is a four-quadrant multiplier, meaning it can handle both positive and negative input signals, enabling applications such as modulation, demodulation, automatic gain control, and power measurement. As a precision analog computational building block, it sits within the broader category of analog signal processing ICs, which are essential in instrumentation, control systems, and communication equipment. Key features include excellent long-term stability, low noise, and high reliability. The device is internally trimmed for accuracy, reducing the need for external calibration. The fully differential Z-input allows flexible signal conditioning, and the ability to achieve gains up to ×10 simplifies system design. The TO-100-10 metal can package provides hermetic sealing, making it suitable for harsh environments. Technically, the AD632 uses a monolithic bipolar process with laser-trimmed thin-film resistors to achieve high accuracy. The transfer function is W = (X1 - X2)(Y1 - Y2)/10V + Z, where Z is the differential Z-input. This architecture supports multiplication, division, squaring, and square-rooting functions. The device is designed for precision analog computation, with a typical nonlinearity of ±0.5% and a small-signal bandwidth of 1 MHz. Typical applications include analog computation in test and measurement equipment, precision power measurement, process control, and signal conditioning in military and aerospace systems. The AD632SH/883B is particularly suited for applications requiring high accuracy and stability over a wide temperature range. When designing with this device, ensure proper power supply decoupling with 0.1 µF ceramic capacitors close to the supply pins. The output can drive loads down to 2 kΩ, and the Z-input can be used for offset adjustment or to sum signals. For division mode, the Y-input must be positive to avoid instability.

RFQ پەیوەندی