Amplifier ICs
بەرهەمەکان (3,200+)
LT1214CS - 28MHz 12V/us Quad Precision Op Amp | Analog Devices
Analog Devices LT1214CS is a four-amplifier precision operational-amplifier IC with a 28 MHz typical gain-bandwidth product, 12 V/us typical slew rate, and a 16-lead SOIC package. Designed for single-supply operation, the device combines four general-purpose amplifiers in one package and supports precision signal conditioning, filtering, and gain-stage applications. The verified manufacturer material identifies LT1214CS as the quad version of the LT1213/LT1214 precision amplifier family. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The operational-amplifier category belongs to the broader analog-amplifier hierarchy and supports DC-precision signal conditioning, instrumentation, buffering, active filtering, and closed-loop control. In a feedback network, the LT1214CS can set closed-loop gain and signal polarity while using its 28 MHz bandwidth and 12 V/us slew rate to reproduce changing waveforms with relatively low delay. The verified data identifies a typical 28 MHz gain-bandwidth product and 12 V/us slew rate. It also lists fast settling to 200 uV within 500 ns after a 2 V step and to 1 mV within 1.1 us after a 10 V step. These figures make the four internal amplifiers useful when multiple channels must process comparable signals, particularly in active filters, sensor interfaces, audio paths, and control systems. The DC-precision positioning also helps reduce external trim requirements in systems where offset and drift must be controlled. Architecturally, the LT1214CS places four amplifiers in one 16-lead SOIC rather than requiring four separate packages. A typical application uses each amplifier for a distinct function, such as instrumentation amplification, active filtering, output buffering, or error amplification. The package consolidates routing over one PCB footprint while still providing independent amplifier channels. Because the verified snippets do not provide the complete electrical tables, exact input-offset voltage, input-bias current, noise density, supply-current, and common-mode-range values should be confirmed in the manufacturer datasheet before final design release. Typical uses include multichannel sensor conditioning, precision active filters, audio signal paths, instrumentation front ends, and general-purpose control loops. The quad organization is especially useful when several signals must be amplified consistently within one instrument, converter, or monitoring system. The 16-SO package allows a conventional surface-mount layout, although careful grounding and decoupling remain necessary for stable high-gain operation. The principal design consideration is to verify rail-to-rail behavior, common-mode limits, output swing, and stability requirements for the specific operating conditions. Input and output capacitors should be placed close to their associated pins, sensitive analog traces should avoid switching-current paths, and unused amplifier channels should be configured according to the manufacturer recommendations rather than left floating. This page combines verified manufacturer and distributor information with a parameter-focused application guide, sourcing guidance, and explicit data gaps. It also distinguishes the lead-free LT1214CS#PBF ordering designation from the base LT1214CS MPN instead of treating a packaging-ordering variant as a separate drop-in alternative.
LT1215CS8 - 23MHz Dual Precision Op Amp | Analog Devices
Analog Devices LT1215CS8 is a dual, single-supply precision operational amplifier with a 23 MHz gain-bandwidth product and a 50 V/µs slew rate, housed in an 8-pin SOIC package. The LT1215 family combines two amplifier channels with the DC precision required for instrumentation, signal-conditioning, and active-filter designs. An operational amplifier, or op amp, is a high-gain differential-input amplifier whose feedback network defines its closed-loop behavior. Within the amplifier hierarchy, the LT1215CS8 is a precision operational amplifier used for low-level signal amplification, impedance buffering, filtering, and feedback control. Its dual-channel configuration provides two amplifiers in one compact surface-mount package while reducing the number of components required on a circuit board. The principal highlighted performance characteristics of the LT1215 are its 23 MHz gain-bandwidth product and 50 V/µs slew rate. These values support comparatively fast closed-loop operation and make the device suitable for signal paths that require both bandwidth and slew-rate capability. The manufacturer also describes the LT1215 and LT1216 family as single-supply precision amplifiers whose DC precision eliminates external trimming in most systems. The LT1215 is a dual amplifier, whereas the related LT1216 is a quad version of the same amplifier family. This distinction is important when selecting a package and pin count: the LT1215CS8 uses an 8-pin SOIC, while a quad implementation requires a different package and pin assignment. Design engineers should therefore verify the complete pin description table in the manufacturer datasheet before assigning amplifier inputs, outputs, supply rails, and exposed connections. Typical uses include precision instrumentation, low-level sensor-signal conditioning, active filters, sample-and-hold circuitry, and general-purpose analog signal processing. The two channels can be used together for cascaded stages, differential signal conditioning, or independent amplifier functions. Input and output impedance requirements, allowable common-mode range, noise, offset, and stability behavior should be checked against the application signal range before finalizing the circuit. For single-supply operation, the circuit must provide a suitable bypass strategy around the power pins and maintain the amplifier within its common-mode input range. Decoupling capacitors should be placed close to the device, and sensitive inputs should use layouts that minimize leakage from high-impedance nodes. Output loading and feedback-component selection also affect achievable bandwidth and closed-loop response. This product page combines the manufacturer’s device description with package information, engineering application guidance, selection criteria, and a structured view of the LT1215CS8’s role in precision analog design. It also distinguishes the dual LT1215 from the quad LT1216 and identifies where the manufacturer datasheet is needed for final pin-level implementation decisions.
LT1216CN - 23MHz Quad Precision Op Amp | Analog Devices
The Analog Devices LT1216CN is a quad precision operational amplifier with 23 MHz gain-bandwidth product, 50 V/us slew rate, and single-supply operation in a 14-pin PDIP package. It is the quad version of the LT1215 family and is designed for instrumentation, signal-conditioning, filtering, and control applications that require a combination of DC precision and high-speed dynamic performance. An operational amplifier is an active analog building block that amplifies the voltage difference between its inverting and non-inverting inputs. The LT1216 belongs to the broader hierarchy of amplifier IC, instrumentation amplifier, and operational amplifier products used in precision signal chains. Its precision characteristics reduce the need for external trimming in many systems, while its high bandwidth and slew rate support accurate response to rapidly changing signals. The verified product information identifies the LT1216 as a four-circuit, bipolar, PDIP-14 precision amplifier. The family is specified at 23 MHz gain-bandwidth product and 50 V/us slew rate. The single-supply capability is useful in systems where the signal and supply rails must be referenced close to ground. The package provides four amplifier channels in one component, allowing multiple signal paths to share a common footprint and simplifying board-level layout. The LT1216 family is based on the LT1215 dual amplifier and extends the same precision amplifier architecture to four channels. The combination of high gain-bandwidth product, high slew rate, and DC precision is useful when a design must preserve small-signal accuracy while also handling waveforms with meaningful frequency content. Applications include sensor signal conditioning, active filters, low-level current-to-voltage conversion, data acquisition front ends, and general-purpose analog control. Because the LT1216CN is a monolithic four-channel device, decoupling and grounding remain important design considerations. Each supply rail should be bypassed close to the device with suitable local capacitance, and sensitive analog signals should be routed away from noisy switching nodes. The 14-pin PDIP package also requires adequate spacing and appropriate lead formation during assembly, making it more convenient for through-hole prototypes than for space-constrained surface-mount products. This product page synthesizes the verified manufacturer description, distributor identification, package information, and available comparison references for engineers evaluating the LT1216CN. Because the supplied web data does not include complete electrical tables, pricing values, or a confirmed pin-by-pin diagram, unavailable technical fields are explicitly marked rather than inferred.
LT1216CS - 23MHz Quad Precision Op Amp | Analog Devices
The Analog Devices LT1216CS is a quad precision operational amplifier with 23 MHz typical gain-bandwidth product, 50 V/µs typical slew rate, and four amplifiers in a 16-pin SOIC package. Designed by Linear Technology and offered by Analog Devices, the device combines low-noise signal-chain performance with single-supply operation. An operational amplifier is an analog building block used to amplify voltage differences, buffer signals, drive analog-to-digital converters, and implement active filters. The LT1216 belongs to the precision-op-amp hierarchy, where accurate DC behavior and fast large-signal response are useful in instrumentation, industrial measurement, communications, and test systems. It is a general-purpose precision amplifier rather than a power regulator or switching device. The verified specifications identify a 23 MHz gain-bandwidth product, 50 V/µs slew rate, and fast settling of 250 ns to 0.01% for a 2 V step. The manufacturer describes the LT1216 as a quad version of the LT1215 dual amplifier and states that the devices operate from any supply greater than 2.5 V and less than 36 V total. These figures support both precision low-frequency work and higher-bandwidth signal conditioning. The LT1216 family emphasizes DC precision and high-frequency performance. Its 23 MHz bandwidth provides useful signal amplification bandwidth, while the 50 V/µs slew rate improves response to step-like signals. The manufacturer’s published settling data gives 250 ns typical settling to 0.01% after a 2 V step and 480 ns after a 10 V step to 1 mV, making circuit simulation and feedback-loop design important. Typical uses include instrumentation amplifiers, active filters, buffer stages, communication interface circuits, data-converter front ends, and precision control systems. The quad format can reduce the number of external amplifier packages when four independent channels are required, although input, output, supply, and common-mode limits must still be checked independently. For PCB design, keep input and feedback traces short, use a solid ground reference, place compensation or decoupling components according to the manufacturer’s application guidance, and verify stability with the selected gain and load. For replacements, the LT1215 is a dual-package family member but is not a pin-compatible substitute for this 16-pin quad device; package and pin count must be checked before any redesign. This product page consolidates verified manufacturer and distributor information, package details, technical specifications, practical design considerations, and replacement guidance to support faster engineering evaluation.
LT1222IS8 - 500MHz Low-Noise Op Amp | Analog Devices
Analog Devices LT1222IS8 is a low-noise, very-high-speed operational amplifier with a 500 MHz gain-bandwidth product, 3 nV/√Hz input-noise voltage density, and 200 V/µs slew rate in an 8-pin SO package. The LT1222IS8 is a single-amplifier device intended for instrumentation and signal-processing applications that require both wide bandwidth and low noise. It is stable at a noise gain of 10 or greater without external compensation. An operational amplifier is an analog amplifier that uses differential feedback to control gain, bandwidth, and output behavior. Within the semiconductor hierarchy, the LT1222IS8 is a voltage-feedback operational amplifier, a type of analog integrated circuit used for precision signal conditioning, current-voltage conversion, buffering, and gain control. Its combination of high speed and low noise places it between general-purpose precision amplifiers and wideband instrumentation amplifiers. Principal features include a 500 MHz gain-bandwidth product, 200 V/µs slew rate, and input noise density of 3 nV/√Hz. The device is stable without compensation at noise gains of 10 or higher. For lower closed-loop gains, external compensation can be used, although bandwidth and slew-rate performance are reduced. The LT1222IS8 also provides improved DC characteristics relative to earlier high-speed amplifiers, including reduced input offset voltage and lower input bias current. The architecture combines low-noise bipolar input behavior with wideband frequency response. Noise-gain stability is important in practical layouts because feedback resistors determine both closed-loop gain and the minimum noise gain. Capacitive-load drive and external compensation provide additional control when driving cables, ADC input networks, or other nonideal loads. The maximum input offset voltage listed for the device is 300 µV, making it more appropriate for fast signal paths than for ultra-high-accuracy DC measurements requiring nanovolt-level offsets. Typical uses include low-noise instrumentation front ends, high-speed instrumentation amplifiers, active filters, pulse-shaping circuits, video and communication signal conditioning, photodiode amplification, and high-speed data-acquisition interfaces. In these systems, the 500 MHz bandwidth preserves short rise times, while 3 nV/√Hz input noise limits the amplifier's contribution to weak-signal measurement noise. The 200 V/µs slew rate also helps preserve amplitude accuracy when large input steps must be reproduced quickly. Designers should place input and feedback components close to the amplifier, minimize parasitic capacitance, and use short, properly terminated output paths. Avoid standard 0.1 µF decoupling capacitors directly at high-speed signal pins because their effective impedance and instability can degrade the response. Confirm stability with the actual source impedance, load capacitance, and feedback network before increasing bandwidth or operating at low noise gains. This product page brings together the manufacturer's operating characteristics, orderable same-family alternatives, package details, and practical high-speed layout guidance. It also distinguishes electrically similar suffixes from lower-gain or differently compensated devices so engineers can verify pin compatibility, temperature grade, and bandwidth before making a board-level substitution.
LT1223CJ8 - 100MHz Current Feedback Amplifier | Analog Devices
The Analog Devices LT1223CJ8 is a single-circuit, 100 MHz current-feedback operational amplifier in an 8-lead CERDIP through-hole package. Its three headline characteristics are 1000 V/µs slew rate, ±15 V supply capability, and 1 mV input offset voltage. The device combines a 100 MHz bandwidth with very good DC characteristics, making it suitable for high-speed analog signal conditioning, video amplification, and active cable termination. A current-feedback amplifier is a closed-loop amplifier topology that uses a feedback impedance to set gain rather than relying primarily on a closed-loop gain-bandwidth relationship. Within the LT1223CJ8, this architecture preserves useful bandwidth at higher closed-loop gains, unlike many conventional voltage-feedback operational amplifiers whose bandwidth falls rapidly as gain increases. The LT1223 family therefore remains useful in video, imaging, and communications designs where wide signal bandwidth must coexist with accurate analog gain. The LT1223CJ8 provides 1000 V/µs slew rate, 50 mA output current, 6 mA quiescent current, and 5 MΩ input resistance. Its input offset voltage is 1 mV, input bias current is 1 µA, and settling time to 0.1% is 75 ns. These characteristics allow the amplifier to process rapidly changing signals while rejecting large common-mode inputs and driving analog signals over double-terminated cables. The LT1223 uses a current-feedback architecture optimized for gain distribution through external feedback networks. Resistor selection directly influences gain, bandwidth, and stability, so the feedback and balancing networks should be implemented using the values and layout guidance in the manufacturer datasheet. Its wide supply range of ±15 V accommodates split analog rails commonly found in video and instrumentation systems. Typical applications include video signal conditioning, cable-driver outputs, AGC and IF-chain amplification, test and measurement front ends, photodiode preamplification, and high-speed analog processing. The 50 mA output-drive capability is particularly useful when driving terminated transmission lines or downstream instrumentation stages, while the 100 MHz bandwidth supports video-bandwidth signals. The principal design consideration is that current-feedback amplifiers are not interchangeable with conventional voltage-feedback amplifiers without checking stability and gain-network values. Place the feedback components close to the amplifier pins, follow the recommended reference resistor arrangement, and provide suitable bypass capacitance on both supply rails to minimize parasitic gain and preserve settling performance. This page combines manufacturer-datasheet specifications, verified distributor listings, package information, practical high-speed layout guidance, and application-focused engineering context. It also records the absence of a verified pin-for-pin, same-package substitute so that engineers can evaluate lifecycle and sourcing decisions without relying on unverified cross-reference listings.
LT1230CS - Quad 100MHz Current Feedback Amplifier | ADI
The Analog Devices LT1230CS is a quad 100 MHz current-feedback amplifier with four amplifiers in a 14-pin SOIC package, a 4 V to 30 V supply range, and operation from single or dual supplies. Its 100 MHz bandwidth supports high-speed signal conditioning, while the current-feedback architecture is suited to low-gain stages with high slew rate. The device is identified by the CS commercial-temperature ordering code. A current-feedback amplifier is a voltage-feedback amplifier variation that controls bandwidth and stability through feedback impedance. Current-feedback amplifiers belong to the broader operational-amplifier, analog-amplifier, and semiconductor hierarchies. They are frequently selected where conventional voltage-feedback amplifiers require gain compensation across multiple closed-loop gains or where rapid large-signal response is more important than rail-to-rail input or output operation. The verified source data identifies 100 MHz bandwidth, a 2500 V/µs slew-rate figure for the CS#TR variant, 30 mA output-drive capability, 0.04% differential gain, and 0.1° differential phase. It also reports 25 MΩ input impedance with 3 pF input capacitance. These figures make the LT1230CS appropriate for video, communications, instrumentation, and general high-speed analog interfaces when the circuit operates within the verified supply and package limits. The CS package is a 14-pin SOIC measuring 0.154 inch, or 3.90 mm, in body width. The quad topology lets one device provide four high-speed amplifier sections while reducing package count, although common power, ground, bypass, and thermal-management requirements still apply. Supply decoupling should be placed close to the device, and unused amplifier sections should be configured according to the manufacturer guidance rather than left floating. Typical applications include video buffering, high-speed data acquisition, communications-interface signal conditioning, active filtering, and instrumentation. The LT1230CS is particularly relevant where the required bandwidth and slew behavior outweigh the need for rail-to-rail operation. Designers should verify package pin assignments, recommended feedback networks, output loading, and supply sequencing against the official manufacturer datasheet before layout release. This page combines verified manufacturer and distributor information with package, application, and design guidance. Because no verified internal pricing or complete pin-level datasheet extract was supplied, missing engineering values are marked rather than inferred. The result is intended to help engineers identify whether the LT1230CS fits a design before obtaining the complete official datasheet and validating the application circuit.
LT1252CS8 - 100MHz Current-Feedback Video Amplifier | Analog Devices
The Analog Devices LT1252CS8 is a single-channel, low-cost current-feedback video amplifier with a 100 MHz bandwidth, flat to 0.1 dB, and a wide ±14 V (28 V total) supply range. The device is offered in an 8-pin SOIC surface-mount package for low-impedance video-cable, RGB, composite-video, and active-filter applications. The LT1252 family is listed in production by Analog Devices. A current-feedback amplifier is a voltage-feedback amplifier variant in which the inverting input and output are connected through a feedback impedance. This topology supports wide closed-loop bandwidth and high slew rate, making it useful when driving terminated cables, video distribution networks, and filters. It belongs to the operational-amplifier hierarchy, specifically the video-amplifier and low-cost video-buffer segment of analog signal-chain ICs. The LT1252's major features include a 100 MHz bandwidth with 0.1 dB flatness, a wide ±14 V supply capability, and current-feedback operation suited to low-impedance loads. Its bandwidth is especially valuable for RGB signals routed between PCs and workstations, while its video-focused characteristics support composite-video distribution. The single-channel architecture also makes it appropriate for point-to-point video links where a quad amplifier would add unused channels. Unlike a general-purpose voltage-feedback amplifier, the LT1252 uses current feedback to maintain high bandwidth across a broader range of feedback resistor values. This architecture is particularly effective in video gain stages where the signal source and load impedance require a high-output-current buffer. Engineers should nevertheless evaluate the complete gain network, including the feedback resistor and optional compensating capacitor, against the closed-loop gain and required stability margin. Typical applications include composite-video line drivers, RGB video distribution, cable-driving buffers, active filters, and low-impedance video signal conditioning. The S8 package supports compact analog boards while providing separate supply and output pins for straightforward routing. When cascading several amplifiers, preserve video bandwidth and avoid operating near gain or output-swing limits that could distort synchronized signal transitions. For reliable layouts, place input, feedback, and decoupling networks close to the associated device pins, and provide a low-impedance return path for each supply rail. A common design mistake is to copy a feedback value from a voltage-feedback amplifier without recalculating it for the LT1252 current-feedback topology. Validate the completed channel with the intended cable length and load because distributed capacitance and termination can alter bandwidth and output stability. This page combines the manufacturer's device characteristics, verified distributor identification, drop-in replacement information, practical PCB guidance, and an application-oriented comparison. It is designed to help engineers identify whether the LT1252CS8 fits a video-buffer design before beginning detailed gain, feedback, and signal-integrity calculations.
LT1253CS8 - Dual 270MHz Current-Feedback Video Amplifier | Analog Devices
Analog Devices LT1253CS8 is a low-cost, dual, current-feedback video amplifier with two independent amplifier channels in an 8-pin SOIC package. It features a 270 MHz small-signal bandwidth, 250 V/µs slew rate, 55 mA output current per channel, and a wide ±14 V supply range. The LT1253 family is intended for video applications requiring wide bandwidth, fast signal transitions, and channel isolation. A current-feedback amplifier is a voltage-feedback amplifier architecture whose bandwidth and stability behavior can change with feedback resistance. This architecture is commonly used in video, imaging, and communications circuits that require high gain-bandwidth performance. The LT1253CS8 belongs to the broader operational-amplifier hierarchy, combining analog signal amplification with video-focused bandwidth and isolation characteristics in one integrated circuit. The two amplifier channels are isolated except for their shared power-supply pins. According to the Analog Devices LT1253 product page, this isolation exceeds 94 dB at 5 MHz, helping reduce crosstalk when two independent video signals pass through the same package. The 270 MHz bandwidth and 250 V/µs slew rate also make the device suitable for video buffering, distribution, and gain stages operating with larger-amplitude transitions. The LT1253CS8 accepts single or dual supplies across a ±14 V range and uses approximately 6 mA of supply current per channel under the stated operating conditions. Its 55 mA output-current capability provides suitable drive for practical video stages, while the current-feedback architecture supports the high operating frequencies associated with the family. Designers should account for amplifier input/output network values when setting gain because current-feedback amplifiers commonly use external feedback resistors. Typical uses include professional video distribution, camera and imaging signal chains, monitor signal conditioning, broadcast equipment, and general-purpose high-speed analog amplification. The dual configuration reduces the component count compared with two separate single amplifiers and simplifies power-supply bypassing. It is particularly useful when two video channels must share a board area but still require strong isolation from one another. For PCB implementation, place the power-bypass capacitors close to the supply pins and keep feedback and compensation components adjacent to their associated amplifier pins. Maintain short return paths for high-speed video signals, use a continuous ground reference, and avoid routing sensitive video traces adjacent to switching nodes or other high-energy timing signals. The 8-pin SO package also allows rework and inspection more easily than many fine-pitch alternatives. This product page combines the LT1253 family architecture, 270 MHz bandwidth, 250 V/µs slew rate, supply range, isolation, and package information with practical guidance on video-signal routing, power bypassing, replacement selection, and design trade-offs. It helps engineers identify whether the dual SOIC LT1253CS8 satisfies their bandwidth, isolation, supply, and sourcing requirements before beginning layout.
LT1256CN - 40MHz Video Fader Amplifier | Analog Devices
The Analog Devices LT1256CN is a 40 MHz video fader and DC gain controlled amplifier: a two-input, one-output current-feedback amplifier whose linear control circuit sets how much each input contributes to the output, offered in a 14-pin PDIP (N-14) through-hole package. Its headline specifications are 40 MHz small-signal bandwidth, 300 V/us slew rate, and single-supply operation from 5 V to 30 V. The manufacturer lists the LT1256 as PRODUCTION, with a lead-free ordering code (LT1256CN#PBF) also offered. A video fader is a controlled-gain summing amplifier used to blend two signal sources smoothly and repeatably, typically in broadcast video equipment, audio consoles, keyers, and AGC loops. The LT1256 belongs to the current-feedback amplifier family, itself a subset of operational amplifiers, inside the broader category of analog signal-conditioning integrated circuits. Its linear control characteristic means a control voltage produces a proportional change in signal contribution, which makes the part well suited to automated mix and fade systems rather than purely manual potentiometer fading. Key features include two independently weighted inputs, DC gain control in addition to the fading function, 40 MHz bandwidth with 300 V/us slew rate for full-amplitude video signals, and a wide 5 V to 30 V supply range that allows the part to run from legacy analog rails or modern low-voltage systems. Because the control loop is linear rather than logarithmic, the part can also be used as a programmable attenuator, an analog multiplier element in filter and modulation blocks, and as the forward path of a closed-loop gain-control system. The current-feedback topology is the key architectural point: in a current-feedback amplifier the closed-loop bandwidth is largely set by the external feedback resistor rather than by the closed-loop gain, so large-signal performance stays consistent as the control voltage changes gain. The result is that signal amplitude does not visibly change color or slew rate while fading, and distortion stays low at large video amplitudes. Typical applications include broadcast video switchers and mixers, video keyers and titlers, audio mixing consoles, automatic gain control front ends for cameras and RF receivers, lab-grade attenuator and filter test setups, and general instrumentation where a variable, precisely weighted gain element is needed. When laying out an LT1256 design, treat the feedback resistor and the compensation capacitor as part of the gain-setting network: keep them close to the device, use a 0.1 uF ceramic bypass on each supply rail, and verify output swing headroom at the highest control voltage, because the output typically approaches the supply rails on a single-supply configuration. This page consolidates manufacturer specifications, package and lifecycle detail, verified drop-in alternatives, comparison parameters, and practical layout guidance in one place, so engineers can qualify the LT1256CN for a new mixer or fade block without cross-checking several documents.
LT1260IS - Triple 130MHz Current Feedback Amp | Analog Devices
Analog Devices LT1260IS is a triple current-feedback operational amplifier rated for 130 MHz operation, supplied in a 16-lead SOIC package. Each of its three independent amplifiers supports a wide supply range from a single 5 V rail through ±15 V, while active supply current is 5 mA per amplifier. The LT1260IS also provides shutdown control, allowing unused amplifiers to be placed into a zero-supply-current state for power conservation. A current-feedback operational amplifier is a high-speed voltage-amplifier topology whose closed-loop bandwidth depends primarily on the feedback resistor rather than the closed-loop gain. Current-feedback amplifiers are commonly used for video, communications, instrumentation, and other signal chains requiring large slew rate, low distortion, and reliable drive into low-impedance loads. The LT1260 family combines these characteristics with a triple amplifier configuration, allowing one device to support several independent channels. The LT1260IS provides 90 MHz small-signal bandwidth, more than 30 MHz of 0.1 dB gain-flatness bandwidth, and a 1600 V/µs high slew rate. These figures distinguish it from general-purpose operational amplifiers whose bandwidth and transition performance are usually much lower. The combination is particularly useful when processing composite video, driving short cable runs, amplifying high-speed control signals, or operating several phase-related channels in compact equipment. Each amplifier combines a current-feedback core with shutdown capability. When shutdown is asserted, the corresponding amplifier draws approximately 0 µA from the supply, reducing the overall power requirement of systems that do not need all three channels active. The architecture is intended to maintain linearity while driving cables and other low-impedance loads, making channel-to-channel implementation straightforward when identical gain-setting networks and routing practices are used. Typical uses include RGB video amplification, low-impedance cable drivers, communications-interface signal conditioning, industrial control interfaces, and instrumentation. In a three-channel RGB application, the three amplifiers can process red, green, and blue signals in parallel while preserving consistent bandwidth and slew capability across the channels. The same arrangement can support three-coordinate control, test, or monitoring channels where independent outputs are required. PCB implementation should prioritize short feedback loops, symmetrical routing, solid ground-plane continuity, and careful decoupling. Place the amplifier supply bypass capacitors close to the supply pins and keep feedback resistors close to the relevant output and inverting-input pins. Because a current-feedback amplifier relies on a low-impedance feedback network, route both sides of each feedback connection over continuous ground and avoid shared narrow copper paths between channels. This page organizes the LT1260IS specifications, package information, practical application guidance, and verified same-footprint alternatives for faster engineering selection. It also highlights shutdown, bandwidth, gain-flatness, slew-rate, and power-consumption considerations that help engineers distinguish this triple current-feedback amplifier from lower-speed general-purpose devices.
LT1352CS8 - Dual 3MHz 250mA Operational Amplifier | Analog Devices
Analog Devices LT1352CS8 is a dual, very-low-power, high-speed voltage-feedback operational amplifier with a 3 MHz gain-bandwidth product, 200 V/µs slew rate, and 250 mA output drive capability. It is packaged in an 8-pin SOIC and is designed for instrumentation, buffering, signal-conditioning, and general-purpose analog signal-chain applications. The LT1352 family combines the slewing behavior associated with current-feedback amplifiers with the matched high-impedance inputs expected from a true operational amplifier. An operational amplifier is a voltage-controlled analog amplifier that uses external feedback to set gain and is intended for amplification, buffering, filtering, and signal conditioning. The LT1352CS8 belongs to the broader operational-amplifier hierarchy, which includes voltage-feedback amplifiers, instrumentation amplifiers, comparators, and other precision or high-speed analog IC families. Its dual-channel configuration provides two amplifiers in one package, reducing component count and simplifying layout where two independent channels are required. The verified product information identifies the LT1352/LT1353 family as a very-low-power, high-speed operational-amplifier family with lower supply current and higher slew rate than comparable-bandwidth devices. The LT1352CS8 specifically provides two amplifier channels, a 3 MHz bandwidth rating, a 200 V/µs slew-rate rating, and a 250 mA drive rating. These characteristics make it useful in applications requiring faster edge rates or greater output-current capability than a general-purpose low-power amplifier. The matched high-impedance input architecture is useful when the source impedance is relatively high or when input bias current can disturb the signal node. The high slew rate can improve large-signal response in instrumentation, waveform-generation, and feedback-control circuits, while the 3 MHz bandwidth supports moderate-frequency signal amplification. The 8-pin SOIC package is a conventional surface-mount format suitable for PCB assembly and repair workflows. Typical applications include sensor-signal conditioning, audio and communications buffers, active filters, instrumentation interfaces, data-conversion support circuits, and general analog control loops. When selecting it for a new design, verify the supply-voltage limits, input common-mode range, output swing, noise, offset, and stability requirements against the manufacturer datasheet. The published family description supports the use of the LT1352CS8 for low-power, high-speed dual-channel analog signal processing, but detailed operating limits should be confirmed before finalizing a circuit. This page combines the verified LT1352CS8 product details with practical selection guidance, replacement criteria, and design notes. The key engineering trade-off is the balance between low power consumption, high speed, and output drive in an 8-pin dual operational-amplifier package.
LT1353CS - 250 uA, 3 MHz, 200 V/us Quad Op Amp | Analog Devices
Analog Devices LT1353CS is a quad, very-low-power, high-speed operational amplifier with a 250 uA supply current, 3 MHz gain-bandwidth product, and 200 V/us slew rate. It is supplied in a 14-pin SOIC package for surface-mount industrial, instrumentation, communications, and signal-conditioning designs. The LT1353 family combines the slewing behavior associated with current-feedback amplifiers with matched high-impedance inputs, while retaining conventional operational-amplifier signal handling. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. In the broader signal-chain hierarchy, the LT1353CS belongs to the operational amplifier, analog amplifier, and signal-conditioning IC categories. Its combination of low power consumption and high bandwidth is useful when a circuit must preserve small, rapidly changing signals without consuming a large supply current. The LT1353 provides four amplifiers in one package, making it suitable for multichannel filters, sensor interfaces, buffer stages, and control loops. The 3 MHz gain-bandwidth product supports higher closed-loop bandwidth than a general-purpose low-power amplifier, while the 200 V/us slew rate improves response to fast voltage transitions. The 250 uA supply-current specification is particularly important in portable instrumentation and battery-powered systems where each amplifier contributes to the overall power budget. The device is based on a high-speed, low-power architecture with high-impedance matched inputs. These characteristics make the LT1353CS useful in applications requiring more bandwidth than conventional micropower amplifiers while retaining a low quiescent-power footprint. Users should account for the amplifier’s input-noise performance, output-drive capability, stability requirements, and supply-voltage limits when designing precise analog front ends. Typical uses include low-frequency instrumentation, active filters, current-to-voltage conversion, sensor signal conditioning, and general-purpose analog amplification. In portable measurement systems, the quad organization can reduce board area by consolidating four gain stages into one package. The device is also suitable for industrial control modules where low supply current helps limit heat generation and supports longer operating intervals in field equipment. For layout, place the bypass capacitor close to the supply pins and route sensitive input signals away from power and output paths. Check the manufacturer datasheet pinout and recommended application circuit before assigning PCB nets. If the output must drive a long cable, capacitive load, or ADC input, verify the resulting stability and settling behavior rather than relying only on slew-rate and bandwidth figures. This product summary combines the manufacturer device description, package information, and cross-reference results to support engineering selection. It highlights the LT1353CS balance of low supply current, 3 MHz bandwidth, and 200 V/us slew rate while identifying the verification points that matter when replacing or integrating a quad precision analog amplifier.
LT1356CN - Quad 12MHz High-Speed Op Amp | Analog Devices
The Analog Devices LT1356CN is a quad, voltage-feedback operational amplifier with 12 MHz gain-bandwidth product, 400 V/µs slew rate, and unity-gain stability in a 14-pin PDIP package. The family is optimized for low power, high-speed signal conditioning, with a maximum supply current of 1.25 mA per amplifier. An operational amplifier is an active analog building block that amplifies the difference between its two input voltages. The LT1356 belongs to the voltage-feedback amplifier hierarchy, which also includes general-purpose precision op amps, instrumentation amplifiers, and buffer amplifiers. Its matched high-impedance inputs and bipolar complementary processing support accurate signal acquisition while preserving the slewing behavior associated with current-feedback amplifiers. The principal features include 12 MHz gain-bandwidth product, 400 V/µs slew rate, 1.25 mA maximum supply current per amplifier, and operation from ±18 V according to the Arrow listing. The amplifier is unity-gain stable and supports capacitive loading through the C-Load operating approach. Input voltage noise is specified at 10 nV/√Hz, while maximum input offset voltage is 800 µV and maximum input bias current is 300 nA. The LT1355/LT1356 family uses a voltage-feedback topology with matched high-impedance inputs and advanced bipolar complementary processing. Because the devices are unity-gain stable, they can be used directly as conventional voltage amplifiers without external compensation. Their combination of bandwidth, slew rate, and supply current is intended to provide a better performance balance than older devices with comparable bandwidth, although exact noise, offset, and bias-current values vary with the selected operating conditions. Typical uses include low-power voltage-feedback stages, video and instrumentation signal chains, analog control loops, active filters, and general high-speed buffering. In instrumentation systems, the four amplifiers can implement multiple gain or filtering channels in one package. The 400 V/µs slew rate supports rapidly changing large-signal waveforms, while the 12 MHz bandwidth allows operation at substantially higher frequencies than low-bandwidth precision amplifiers. When designing around the LT1356CN, verify the external circuit against the actual signal amplitude and frequency. Large outputs at high frequency can require more output-current capability than the small-signal parameters suggest, while capacitive loading can affect stability. The 14-pin PDIP package is not lead-free; compare this ordering option with the documented LT1356CN#PBF lead-free-finish variant when procurement rules require lead-free termination. This page consolidates the verified manufacturer and distributor details, separates known LT1356CN data from missing parameters, and identifies a same-package ordering alternative. It also provides application guidance and design cautions that help engineers evaluate the amplifier without treating incomplete distributor metadata as an exact bill of materials.
LT1356CS - Quad 12MHz, 400V/us High-Speed Op Amp | ADI
Analog Devices LT1356CS is a quad, low-power, high-speed operational amplifier with 12 MHz gain-bandwidth product, 400 V/us slew rate, and a 16-SO package. The device uses a voltage-feedback topology with matched high-impedance inputs while combining the slewing behavior associated with current-feedback amplifiers. Its maximum supply current is specified at 1.25 mA per amplifier, supporting low-power signal-processing systems that require more bandwidth than conventional precision amplifiers can provide. A high-speed operational amplifier is a voltage-amplifying active device used to increase signal amplitude, buffer sources, filter waveforms, or drive downstream circuits. The LT1356 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its unity-gain stability and ability to drive all capacitive loads make it suitable for signal-chain blocks in which predictable closed-loop behavior is needed without external compensation. The LT1356CS provides several performance characteristics suited to demanding analog processing. Its 12 MHz gain-bandwidth product supports accurate gain and phase response at higher signal frequencies than low-speed precision amplifiers. A 400 V/us slew rate provides faster large-signal transitions, while the input-voltage noise density of 10 nV/sqrt(Hz) supports low-noise amplification. Maximum input offset voltage is 800 uV and maximum input bias current is 300 nA. The LT1355/LT1356 family uses advanced bipolar complementary processing and a voltage-feedback amplifier topology with matched, high-impedance inputs. The topology combines conventional voltage-feedback operation with high slew performance. The LT1356CS is available in a 16-SO surface-mount package, permitting a relatively compact quad-amplifier implementation where board area and channel count are both important. Typical uses include video and image-signal processing, high-speed instrumentation, active filters, waveform drivers, communications interfaces, and general-purpose low-power signal conditioning. The 12 MHz bandwidth can be especially useful in filters whose useful signal band lies well below the amplifier's unity-gain frequency. The 400 V/us slew rate also helps preserve fidelity when processing square waves, pulse trains, or other signals with fast transitions. Designers should verify closed-loop stability, output-swing limits, capacitive-load behavior, and power-supply headroom for the selected gain and signal amplitude. The exact pin mapping, full temperature limits, electrical-characteristic curves, and package details should be confirmed in the manufacturer datasheet before layout or production release. Distributor pricing and stock status were not numerically available in the verified data as of 2026-10-29.
LT1357CN8 - 25MHz 600V/us Voltage-Feedback Op Amp | ADI
The Analog Devices LT1357CN8 is a single voltage-feedback operational amplifier with a 25 MHz gain-bandwidth product and a 600 V/us slew rate, housed in an 8-pin PDIP package. It uses advanced bipolar complementary processing and combines the topology of a voltage-feedback amplifier with the slewing characteristics of a current-feedback amplifier. A voltage-feedback operational amplifier is a general-purpose analog building block that amplifies the difference between its inverting and non-inverting inputs. Within the broader IC hierarchy, it belongs to the amplifier IC class, performs closed-loop signal conditioning, and can operate as a voltage amplifier, current buffer, comparator with an external bias arrangement, or a driver for downstream analog and mixed-signal circuits. Key characteristics include a 25 MHz gain-bandwidth product, a 600 V/us slew rate, and approximately 30 mA supply current. According to the Analog Devices LT1357 datasheet, the device provides lower supply current, lower input offset voltage, lower input bias current, and higher DC gain than amplifiers with comparable bandwidth. These properties make it useful where accurate small-signal behavior must coexist with rapid large-signal transitions. The LT1357 uses a voltage-feedback topology optimized for conventional gain-setting networks. Its high speed makes gain-bandwidth and slew-rate limits important in pulse, video, instrumentation, and feedback-control systems. The 8-pin PDIP package supports through-hole assembly and prototyping, while the single-amplifier configuration leaves two spare inputs available for grounding or shielding. Typical uses include low-level signal conditioning, current-to-voltage conversion, active filtering, analog instrumentation, and pulse-shaping stages. The 600 V/us slew rate supports faster edge reproduction than many general-purpose amplifiers, while the 25 MHz bandwidth covers applications extending into the low megahertz range. When designing a board around the LT1357CN8, follow the datasheet pinout and decoupling recommendations closely. Keep input and feedback traces short, provide clean supply bypassing, and account for resistor loading when calculating closed-loop gain and bandwidth. This page consolidates the manufacturer specifications, package details, equivalent-part information, and practical design guidance into one engineering reference for evaluating the LT1357CN8 in new amplifier designs.
LT1367CS - Quad Precision Rail-to-Rail Op Amp | Analog Devices
Analog Devices LT1367CS is a production quad precision operational amplifier with rail-to-rail input and output capability, supplied in a 14-lead SO package. The device provides four amplifier channels, a standard quad operational-amplifier pinout, and a listed gain-bandwidth product of 400 kHz. Its rail-to-rail input and output architecture makes it suitable for signal-conditioning circuits operating close to their supply rails. An operational amplifier, or op amp, is a high-gain analog building block used in the amplifier IC category to amplify, buffer, compare, filter, and perform analog signal processing. The LT1367 belongs to the broader precision amplifier hierarchy, combining differential input stages, high open-loop gain, and rail-to-rail signal capability in one integrated circuit. The LT1367CS uses a standard quad layout in the 14-lead SO package. This arrangement allows four precision amplifier channels to be placed on a single PCB footprint. Rail-to-rail input operation is valuable when signals may approach either supply rail, while rail-to-rail output capability helps preserve output-voltage range. The verified distributor listing identifies the LT1367 as a four-circuit, rail-to-rail amplifier in a 14-SO package. The family documentation states that the LT1367 can serve as a plug-in replacement for many standard op amps while improving input and output range and precision. Because the LT1367CS is a quad device in a 14-lead package, board-level substitution requires attention to channel order, supply pins, exposed pad availability, input common-mode limits, output swing, stability, and load capability rather than package name alone. Typical uses include precision signal conditioning, low-frequency analog filtering, transducers, instrumentation, buffered sensor interfaces, and general analog signal chains. The 400 kHz gain-bandwidth figure makes it more appropriate for moderate-bandwidth precision and general-purpose amplification than for high-speed video or RF signal paths. Designers should verify the complete electrical limits from the manufacturer datasheet, including supply voltage, input offset voltage, input bias current, output swing, slew rate, settling time, noise, and temperature range. Decoupling should follow the datasheet recommendations, and output loads must remain within the specified capacitive and resistive limits to preserve stability. This product page consolidates verified manufacturer and distributor information, exact package identification, sourcing details, and pin-compatible replacement findings. It also separates directly supported LT1367CS facts from cross-reference candidates and identifies where additional electrical data is required for a final design decision.
LT1413S8 - Dual 5V Precision Op Amp | Analog Devices
Analog Devices LT1413S8 is a dual general-purpose precision operational amplifier optimized for single-supply 5 V circuits and packaged in an 8-pin SOIC. Its key ratings are 60 µV input offset voltage, 0.1 nA input offset current, 950 kHz gain-bandwidth product, and 0.3 V/µs slew rate. The device also supports ±15 V operation, giving designers a common amplifier platform for 5 V and conventional dual-supply analog systems. An operational amplifier is a high-gain, differential analog building block used to amplify, buffer, filter, compare, and control voltage signals. The LT1413 belongs to the general-purpose operational-amplifier category within the broader amplifier and analog IC hierarchy. Its two amplifiers share a common supply but operate independently, allowing one package to implement functions such as sensor conditioning, error amplification, active filtering, or signal conversion. The LT1413 emphasizes low offset voltage, low input bias current, and practical single-supply performance. The 60 µV offset and 0.1 nA offset current are particularly useful when reducing signal-chain errors near the input. A 950 kHz gain-bandwidth product supports moderate-frequency closed-loop operation, while the 0.3 V/µs slew rate allows comparatively rapid output transitions. The advertised output-current capability exceeds 10 mA at a 330 µA supply current. The dual architecture improves board utilization by providing two amplifiers in one package. Its performance is characterized for both single 5 V supply operation and ±15 V supplies, although the manufacturer identifies 5 V as the optimized use case. The same-family LT1013 heritage provides a familiar general-purpose precision-amplifier position, while the LT1413 is described by Analog Devices as a low-cost, upgraded version of that industry-standard device. Typical uses include 5 V sensor interfaces, low-level signal conditioning, active filters, instrumentation amplifiers, sample-and-hold stages, and general analog control loops. The SOIC package also allows a conventional surface-mount implementation without requiring a through-hole footprint. Designers should nevertheless verify output swing, input common-mode range, stability, and load drive at the intended supply voltage before finalizing a circuit. For a new 5 V design, the primary design consideration is power-headroom management. Input and output operating ranges, common-mode limitations, and output-swing behavior must be checked against the actual signal. The manufacturer datasheet also identifies channel separation of 140 dB as an achieved specification, which can be valuable when both amplifiers operate on small signals in the same assembly. This page consolidates the official product information, distributor availability, pricing, same-package alternatives, and practical engineering guidance into one searchable reference. The comparison and design notes clarify where the LT1413S8 fits while preserving explicit uncertainty where volume pricing, lead time, or verified alternative specifications were not supplied.
LT1457S8 - Dual Precision JFET Op Amp | Analog Devices
Analog Devices LT1457S8 is a dual, precision JFET-input operational amplifier optimized for large capacitive loads, with 220 µV offset voltage in plastic and surface-mount packages. The device provides 50 pA input bias current and 20 pA input offset current at 70°C, together with 130 dB channel separation. It is supplied in an 8-pin SOIC package. A JFET-input operational amplifier is a voltage-amplifier IC whose field-effect input stage uses junction FETs. Within the semiconductor hierarchy, the LT1457S8 is an op amp, analog amplifier IC, and signal-conditioning component. Its low-bias-current input stage is useful when measuring signals from high-impedance sources, while its large-capacitive-load optimization helps maintain stability in practical analog circuits. The principal features include a dual amplifier configuration, precision DC input offset of 220 µV, very low bias and offset currents at elevated temperature, 130 dB channel separation, and support for input and output voltages up to ±20 V according to distributor data. These characteristics make the LT1457 suitable for precision buffers, instrumentation stages, sensors, and low-frequency signal-conditioning applications. The JFET input stage provides high input impedance without introducing the bias current associated with bipolar transistor inputs. However, users should distinguish that benefit from the LT1457's comparatively low operating speed. Analog Devices identifies the LT1057 as approximately three times faster, while noting that it has lower capacitive-load handling capability. The LT1113 is identified as having 4.5 nV/√Hz voltage noise, emphasizing that different precision JFET amplifiers optimize for different noise, speed, and load-drive combinations. Typical applications include precision instrumentation, low-leakage sensor interfaces, audio and measurement buffers, active filtering, and gain stages driving substantial external capacitance. Because exact noise, gain-bandwidth, slew-rate, supply-current, and temperature-range figures were not supplied in the verified excerpts, designers should confirm those values in the manufacturer datasheet before final sizing. When using the LT1457S8, place the amplifier close to the source and load being conditioned, verify stability with the actual source and load impedances, and check the positive and negative supply rails against the ±20 V maximum cited by the distributor. This page combines verified manufacturer characteristics, distributor package data, ordering information, and application guidance while clearly identifying parameters that still require datasheet confirmation.
LT1462CN8 - Dual Micropower JFET Op Amp | Analog Devices
The Analog Devices LT1462CN8 is a dual micropower JFET-input operational amplifier with a maximum supply current of 45 µA per amplifier, typical input bias current of 1 pA, and an 8-pin PDIP package. It combines low power consumption with picoampere input bias current for precision, high-impedance circuit designs. The device is unity-gain stable with capacitive loads up to 10 nF and can operate with load values up to 10 kΩ. An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sensors, perform active filtering, and implement analog control functions. A JFET-input operational amplifier uses junction field-effect transistors at its input stage, providing very low input bias current. Within the broader hierarchy, the LT1462CN8 is an amplifier IC, specifically a precision-grade dual JFET operational amplifier designed for low-power analog signal conditioning. The LT1462 family's defining characteristic is its combination of low power and very high input impedance. Each amplifier draws no more than 45 µA of supply current, while its typical input bias current is only 1 pA. These characteristics are useful when measuring signals from high-impedance sources because the amplifier contributes minimal loading to the source. The dual configuration also permits two independent amplifier channels in one package. According to the Analog Devices product information, the LT1462 is unity-gain stable for capacitive loads up to 10 nF. This allows direct placement of up to 10 nF at the output without adding a separate isolation resistor in many applications. The output can also drive a 10 kΩ load to within 1.5 V of either supply rail, making the amplifier suitable for low-voltage instrumentation where output headroom matters. Typical uses include precision sensor interfaces, low-level signal conditioning, photodiode amplifiers, capacitive transducers, battery-powered measurement systems, and analog filters. Because the device combines two channels, it can also implement differential, instrumentation, or active-filter topologies when a suitable resistor network and common-mode range are acceptable. When designing around the LT1462CN8, account for the 1.5 V output headroom at a 10 kΩ load and verify the signal's common-mode range at the chosen supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should be kept short and away from switching nodes to minimize leakage and pickup. This page combines the manufacturer's published performance highlights with package details, application guidance, and a structured engineering comparison. It is intended to help designers evaluate the LT1462CN8 for low-power, high-impedance analog designs while recognizing that final circuit performance depends on supply voltage, load, source impedance, stability, and output-headroom requirements.
LT1464CS8 - Dual 1MHz Micropower JFET Op Amp | ADI
Analog Devices LT1464CS8 is a dual, micropower JFET-input operational amplifier featuring 1 MHz gain-bandwidth product, 500 fA typical input bias current, and a maximum supply current of 200 µA per amplifier. The device is packaged in an 8-pin SOIC package. It combines picoampere-level bias current with operation from a single 5 V supply or a split supply, making it suitable for precision, low-power signal-chain designs. An operational amplifier is a voltage-feedback amplifier used to amplify differential signals, buffer sensors, implement active filters, and serve as the gain element in control or instrumentation circuits. The LT1464 belongs to the JFET-input operational amplifier family and the broader voltage-feedback amplifier category. Its low-bias-current input stage is especially useful when the source impedance is high or leakage currents would otherwise disturb the measurement. Key operating characteristics include a 1 MHz gain-bandwidth product, 0.9 V/µs slew rate, 500 fA typical input bias current, and no more than 200 µA supply current per amplifier. According to the Analog Devices LT1464 product information, the amplifiers are unity-gain stable with capacitive loads up to 10 nF. Their outputs can drive a 10 kΩ load to within 1.5 V of either supply rail, supporting practical single-supply signal-conditioning circuits. The JFET input architecture combines low input bias current with the amplifier’s micropower operating current. Gain-bandwidth behavior supports approximately 1 MHz closed-loop bandwidth at unity gain, while the specified output-current capability allows the device to follow higher-frequency signals without requiring a high-power output stage. Designers should still evaluate output swing, load current, and supply voltage together because the usable output range narrows near the rails. Typical applications include low-frequency sensor signal conditioning, current-to-voltage conversion, photodiode and other high-impedance transducers, precision filtering, battery-powered instrumentation, and general dual-amplifier signal chains. The 8-pin SOIC package provides two amplifiers and can simplify PCB layout when both channels are required in adjacent analog sections. A critical design consideration is stability with capacitive loading. The manufacturer specifies unity-gain stability for loads up to 10 nF, so longer sensor cables or unusual load networks may require isolation resistance close to the input. Grounding and bypassing should follow the manufacturer’s recommended application circuit, with short return paths and local supply decoupling to preserve low-noise behavior. This product information combines the manufacturer’s electrical characteristics with practical guidance on low-power operation, capacitive loading, output swing, and PCB implementation. It also organizes the verified ordering options and key limitations into a form that supports direct part selection, sourcing, and circuit design.
LT1465CN - 4-Channel Micropower JFET Op Amp | Analog Devices
Analog Devices LT1465CN is a quad micropower JFET-input operational amplifier with four amplifier circuits in a 14-pin PDIP package. The device is specified for a maximum supply current of 200 uA per amplifier, a typical input bias current of 500 fA, a 1 MHz gain-bandwidth product, and unity-gain stability with capacitive loads up to 10 nF. Its low-power, high-impedance characteristics make it suitable for precision analog signal conditioning, low-level sensing, instrumentation, and battery-powered systems. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages while providing high input impedance, low output impedance, and controlled gain. The LT1465 belongs to the micropower JFET-input operational amplifier category, combining low supply current with very low input bias current. This combination is useful when the signal source has extremely high source resistance or when leakage current would otherwise disturb the measurement. Key features include a 1 MHz gain-bandwidth product, operation from a single or dual supply, and output swing capability that allows a 10 kOhm load to be driven to within 1.5 V of either supply rail. The JFET input stage provides picoampere-level bias current, while the micropower architecture limits supply consumption. The 14-pin PDIP package supports through-hole PCB assembly and conventional socket or leaded-board layouts. The LT1465CN is intended for applications requiring very low input bias current without the higher supply current associated with conventional bipolar input stages. Its unity-gain stability permits direct operation around buffers and voltage followers with capacitive loads up to 10 nF. The 1 MHz gain-bandwidth product is suitable for slow signal-conditioning paths, sensor interfaces, and precision control loops rather than high-speed video or communications channels. Typical applications include pH and chemical-sensor front ends, biomedical instrumentation, photodiode amplifiers, capacitive transducers, low-level current-to-voltage converters, and battery-powered measurement systems. In these applications, the amplifier can sit directly at the sensor output, where the low 500 fA typical bias current helps preserve the integrity of high-impedance signals and reduces the need for unusually low-leakage surrounding components. A key design consideration is power-supply headroom. Output swing is specified to within 1.5 V of either supply when driving a 10 kOhm load, so the supply voltage must remain above the desired output range by the required headroom. Decoupling should be placed close to the supply pins, and the input and output networks should be checked for leakage, bootstrapping, and capacitive-load stability at the actual board level. This page combines the manufacturer product information, distributor listings, package details, and cross-reference findings for LT1465CN. The most important practical distinction is the combination of quad-channel integration, micropower operation, picoampere-class input bias, and a 14-pin PDIP footprint; applications that require a surface-mount package or substantially higher bandwidth need a different device family.
LT1465CS - Quad Micropower JFET Op Amp | Analog Devices
Analog Devices LT1465CS is a quad micropower JFET-input operational amplifier with a maximum supply current of 200 µA per amplifier, typical input bias current of 500 fA, and unity-gain stability for capacitive loads up to 10 nF. The device is offered in a 14-lead SOIC package and is intended for low-power precision signal-conditioning systems that require very low input current and predictable operation with capacitive loads. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its non-inverting and inverting inputs. The JFET-input LT1465CS belongs to the precision amplifier hierarchy, combining low-power operation with high input impedance, low bias current, and rail-to-rail output swing characteristics. Its four independent amplifier sections make it especially useful in compact instrumentation where board area and standby consumption are important design constraints. Key features include a typical input bias current of 500 fA, maximum supply current of 200 µA per amplifier, and unity-gain stability with capacitive loads up to 10 nF. The output can drive a 10 kΩ load to within 1.5 V of either supply rail. These characteristics support low-leakage sensor interfaces, precision current-feedback circuits, battery-powered measurement systems, and signal chains where amplifier input loading must remain small. The JFET input stage provides the core low-bias-current behavior, while the quad configuration integrates four amplifiers into one package. Because the device remains stable at unity gain with substantial capacitive loading, it can be used directly with long sensor wires, switched-capacitor networks, and external sampling or protection structures without requiring an isolation resistor in every case. Rail-limited output swing must still be considered when designing low-voltage signals. Typical applications include precision current measurement, photodiode and other high-impedance sensor interfaces, low-power battery monitoring, industrial instrumentation, data acquisition, and portable test equipment. In each case, the combination of picoampere-class input bias current and low per-amplifier supply current supports accurate sensing while limiting standby demand. For layout, keep the four amplifier sections and their feedback networks close to the corresponding pins, maintain a common ground reference, and place input components away from switching nodes. Review the manufacturer data sheet for the complete pin assignment, supply limits, input and output ranges, and recommended operating conditions before releasing the PCB. This page organizes the manufacturer specifications, sourcing options, drop-in replacement assessment, and application-oriented design guidance for engineers evaluating the LT1465CS. It also distinguishes electrically identical order codes from true cross-brand drop-in equivalents and highlights the package and pin-compatibility checks that matter during redesigns.
LT1468IS8 - 90MHz Precision High-Speed Op Amp | ADI
The Analog Devices LT1468IS8 is a single-channel, precision high-speed operational amplifier with a 90 MHz gain-bandwidth product, 22 V/us slew rate, and 16-bit accuracy. The device settles to within 150 uV of a 10 V output signal in 900 ns and is supplied in an 8-pin SO package. An operational amplifier is an analog signal-processing IC that uses high-gain differential feedback to amplify, buffer, filter, or convert signals. The LT1468 belongs to the precision operational-amplifier hierarchy, combining low DC error with wideband AC performance. This combination makes it useful when a system requires both accurate signal scaling and rapid settling, rather than choosing between slow precision and high speed. The principal performance specifications are a 90 MHz gain-bandwidth product, 22 V/us slew rate, 900 ns settling time to 150 uV for a 10 V signal, and 16-bit accuracy. These figures are particularly relevant for data-acquisition and signal-conversion circuits. The high slew rate supports large output transitions quickly, while the short settling time helps preserve channel-to-channel accuracy after a digital-to-analog converter changes its output. The LT1468 is particularly suited to precision signal chains where amplifier behavior affects overall conversion accuracy. Its 16-bit operating accuracy and fast settling complement current-to-voltage conversion around a DAC and the acquisition of high-resolution ADC outputs. Unlike a general-purpose amplifier optimized primarily for low-cost signal conditioning, the LT1468 targets applications where DC precision and high-frequency response both influence the result. Typical applications include DAC current-to-voltage conversion, ADC input buffering, precision instrumentation, laboratory test equipment, active filters, and high-speed control or signal-conditioning circuits. In a DAC output path, the amplifier helps convert a switched or current-based converter output into a usable voltage. In an ADC front end, it can reduce loading while preserving the required bandwidth. Designers should use the manufacturer’s recommended compensation values and verify closed-loop stability for the selected gain, output load, and cable capacitance. High-speed precision amplifiers can amplify stray capacitance, input-bias-current error, and PCB leakage into output offset or settling errors. Keep feedback loops short, use solid grounding, and place compensation and decoupling components close to the device pins. This product record combines the manufacturer’s operating characteristics, verified orderable-part information, drop-in family alternatives, package details, and application-specific design guidance. It is intended to help engineers identify the correct temperature grade, compensation variant, PCB footprint, and signal-chain role before releasing a production BOM.