Amplifier ICs
بەرهەمەکان (3,200+)
MA5302MSXUMA1 - 2-Ch Class D 440W Audio Amp | Infineon
The Infineon MA5302MSXUMA1 is a 2-channel (stereo) Class D audio amplifier integrated circuit housed in a PG-IQFN-42-1 package, integrating a PWM controller, a high-voltage gate driver, and four low-RDS(ON) power MOSFETs in a multi-chip module (MCM). It delivers up to 440 W of output power and reaches 94% efficiency, supporting 1-2 ohm speaker loads for high-power subwoofer and professional audio systems. The MA5302MS family achieves power density equal to or greater than monolithic alternatives while occupying 50% less PCB space and requiring little or no external heatsink, making it ideal for space-constrained, thermally limited designs. A Class D audio amplifier is a switching amplifier topology that uses pulse-width modulation (PWM) to drive the output stage at high frequency, then low-pass-filters the resulting waveform to recover the audio signal. Compared with linear (Class A/AB) amplifiers, Class D designs achieve far higher efficiency (typically 85-95%) because the output transistors switch between fully on and fully off states instead of operating in their linear region. The MA5302MS belongs to the power amplifier -> audio amplifier -> Class D amplifier -> integrated Class D IC hierarchy within Infineon's MERUS multi-chip-module product line. Key specifications include 440 W maximum output power, 94% efficiency, 2-channel stereo or mono-BTL configuration, 1-2 ohm load support, integrated protection features, and a compact 7x7 mm PG-IQFN-42-1 package. The integrated gate driver and MOSFETs eliminate the need for an external half-bridge, reducing BOM cost and design complexity. The device is the successor to the IR43x2M family and shares the established MERUS audio platform footprint. The MA5302MS uses a multi-chip-module (MCM) architecture combining a 2-channel PWM controller, gate driver, and four power MOSFETs on a single substrate. This topology allows higher output power than monolithic CMOS Class D amplifiers because the discrete MOSFETs can be optimized for low RDS(ON) without competing for silicon area with the control logic. The result is higher continuous output current, lower thermal resistance, and the ability to drive very low-impedance (1-2 ohm) speaker loads that would otherwise require large external heatsinks. Typical applications include powered subwoofers, home theater systems, professional PA speakers, soundbars, marine audio systems, and automotive aftermarket amplifiers. The wide load range (1-2 ohm) makes it particularly suitable for subwoofer designs where low-impedance voice coils are common and high continuous power is required. When designing with this device, follow the Infineon reference design for board layout, output filter selection, and thermal management. The integrated protection suite includes thermal shutdown, overcurrent, and undervoltage lockout, but the PCB copper pour and thermal via pattern must still support continuous high-power operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
MA5342MSXUMA1 - 2x200W Class D Audio Amplifier MCM | Infineon
The Infineon MA5342MSXUMA1 is a 2x200W stereo Class D audio amplifier multi-chip module (MCM) integrating a 2-channel PWM controller, a high-voltage gate driver, and four low-RDS(ON) MOSFETs in a 7x7 mm PG-IQFN-42-1 package. It delivers equivalent or higher output power than monolithic alternatives while occupying 50% less board space and requiring little or no heatsink, achieving up to 95% efficiency. A Class D audio amplifier is a switching amplifier topology that uses pulse-width modulation (PWM) to drive the output stage at high frequency, then low-pass filters the resulting square wave to recover the audio signal. Compared to Class AB linear amplifiers, Class D amplifiers achieve significantly higher efficiency (typically 85-95% versus 50-70%), reducing power dissipation and enabling smaller form factors. The MA5342MSXUMA1 belongs to the amplifier IC family -> audio amplifier -> Class D amplifier -> power management IC taxonomy used by audio system designers. Key features include 2x200W continuous output power into 4 ohm loads, an integrated 49.2 mOhm RDS(ON) output stage, analog input interface, and support for supply voltages across the PG-IQFN-42-1 high-power split-rail topology. The device is footprint-compatible with the predecessor IR43x2M family, enabling drop-in upgrades in existing designs without PCB rework. Operating modes support both single-ended and bridge-tied load (BTL) configurations, covering home theater, soundbar, and subwoofer applications. The MA5342MSXUMA1 uses Infineon's proprietary MCM packaging that mounts the controller die, gate driver die, and four power MOSFET dice in a single leadless package. This reduces parasitic inductance between the gate driver and MOSFET gates, improving switching performance and EMI characteristics. The exposed thermal pad enables direct PCB heat spreading, allowing the part to deliver full-rated power without an external heatsink in typical 4 ohm applications. Typical applications include home theater receivers, powered stereo speakers, soundbars, subwoofers, automotive infotainment amplifiers, and professional powered monitors. The high efficiency and compact footprint make it well suited for slim-form-factor audio products where thermal management is constrained. When designing with the MA5342MSXUMA1, follow the reference design's LC output filter values to maintain loop stability and meet EMI targets. The exposed pad must be soldered to a sufficiently large copper pour for thermal dissipation - failure to do so can cause thermal shutdown at high output levels. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
MAX14515AEWA+T - High-Voltage Liquid Lens Driver 8-WLP | Maxim Integrated
The Analog Devices (Maxim Integrated) MAX14515AEWA+T is a high-voltage liquid lens driver IC that combines a charge-pump boost converter with an integrated H-bridge driver, controlled through an I²C interface, in an 8-bump WLP package. It provides a compact, differential AC output for tunable liquid lenses used in miniature autofocus camera modules, replacing bulkier discrete HV-driver solutions. A liquid lens driver is a specialized power-management IC that converts a low-voltage DC source into the bipolar, AC high-voltage waveform required to deform an electrowetting-based liquid lens, thereby adjusting optical focus. Liquid lens drivers sit within the camera-module subsystem alongside image sensors, ISP front-ends, and voice-coil/focus actuators, forming the hardware chain that delivers electronically-tunable focus to smartphones, webcams, AR/VR cameras, machine-vision heads, and barcode scanners. Key features include I²C-controlled output voltage amplitude adjustment, integrated H-bridge for bipolar lens excitation, internal charge pump that boosts a 2.7V–5.5V supply up to lens-driving levels, low-power shutdown mode, small-footprint 8-bump WLP (Wafer-Level Package), and minimal external component count. The high-voltage differential output directly drives the lens cell, eliminating the need for an external transformer or high-voltage amplifier. From an architecture standpoint, the MAX14515 uses a Dickson charge-pump stage to generate the high DC rail, followed by an H-bridge that commutates that rail at the lens-resonance frequency to produce the AC field. The I²C interface provides register-based amplitude and mode control, while internal logic manages start-up sequencing and fault protection. The 8-WLP package dramatically reduces board area, which is critical for camera modules where z-height and x/y footprint are tightly constrained. Typical applications include autofocus liquid-lens modules in smartphones and tablets, AR/VR camera lenses, security and surveillance cameras with electronic focus, industrial machine-vision cameras, and endoscope/imaging probes. Its minimal BOM and small footprint suit camera-module integration where space is at a premium and lens drive efficiency matters. When designing with this device, ensure the I²C bus pull-ups match the controller's logic level and place the charge-pump flying capacitors as close to the IC as possible. Verify that the lens-resonance frequency lies within the part's commutating range, and respect the WLP's strict MSL1 handling requirements to avoid bump-damage during reflow. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing engineers with a single decision-ready reference for sourcing and second-sourcing the MAX14515AEWA+T liquid-lens driver.
MAX14807ECB+T - Dual 2.2A 220Vpp Analog Pulser | Analog Devices
The Analog Devices MAX14807ECB+T is a dual, high-voltage analog pulser with 2.2A output current and waveform capability up to 220Vpp. The integrated circuit combines a differential amplifier, a Class AB push-pull output stage, and an active clamp for driving piezoelectric transducers in ultrasound systems without an external transformer. It operates in analog and digital modes, giving designers a single high-voltage driver for generated waveforms and controlled pulses. A high-voltage analog pulser is an integrated signal-conditioning and power-driver circuit that converts low-voltage commands or differential analog signals into substantially larger voltage and current levels. This device sits between a low-voltage signal source and a piezoelectric transducer, combining amplifier, gain selection, output-stage drive, active clamping, and protection functions in one package. That integration reduces the number of external high-voltage signal-chain stages required in an ultrasound transmitter. The MAX14807 features gain selection between 28dB and 40dB for its differential input amplifier. Analog mode uses this gain-selectable amplifier and Class AB push-pull output stage to produce high-voltage arbitrary waveforms. Digital mode provides direct high-voltage pulse generation, while the external bias resistor establishes the output-stage bias current. According to the manufacturer datasheet, the active clamp presents a 25Ω low-impedance path to ground, helping discharge the transducer output and return the circuit to a defined state between pulses. The device supports waveforms or pulses up to 220Vpp and provides output current of 2.2A. These ratings make it relevant to ultrasound imaging, industrial acoustic testing, nondestructive evaluation, piezoelectric positioning, and laboratory waveform systems. Because the output stage is intended to drive a capacitive transducer, pulse duration, repetition rate, duty cycle, transducer capacitance, and output dissipation should be evaluated together rather than independently. A key design consideration is that a 220Vpp capability does not eliminate the need for careful board-level insulation, creepage, clearance, and high-voltage layout practices. Keep high-voltage copper away from low-level inputs and external programming interfaces. Follow the manufacturer datasheet for bypass capacitors, bias-resistor selection, transducer connections, exposed-pad layout, and thermal constraints. This product page consolidates the manufacturer's operating modes and electrical highlights with application guidance, engineering design notes, lifecycle information, and an authenticity-controlled comparison of available drop-in alternatives. It is intended to help engineers evaluate whether the MAX14807ECB+T matches a high-voltage pulser requirement before committing a PCB layout.
MAX4061EUA+ Differential Microphone Preamplifier | Maxim
The Maxim Integrated MAX4061EUA+ is a 1-channel Class AB differential microphone preamplifier with adjustable gain, internal microphone bias, and complete shutdown, housed in an 8-uMAX/uSOP package. The verified distributor listing identifies it as an Amplifier IC, while the manufacturer-family description identifies the MAX4060/MAX4061/MAX4062 family as differential-input microphone preamplifiers optimized for notebook and PDA audio systems. The device is intended for portable audio signal chains where a small microphone signal must be amplified while rejecting supply and common-mode noise. A microphone preamplifier is an audio amplifier IC that receives a small differential signal from an electret or differential microphone and raises it to a level suitable for downstream audio processing. In the broader electronics hierarchy, this component belongs to amplifier ICs, audio amplifiers, microphone preamplifiers, and portable audio signal-chain devices. Its differential-input architecture helps reject noise that appears equally on both microphone inputs, while adjustable gain allows the circuit to accommodate different microphone sensitivities. The verified family description specifically highlights internal bias, excellent power-supply rejection and common-mode rejection ratios, and low-noise operation. The MAX4061EUA+ additionally includes complete shutdown according to the listed family description, supporting power management in portable equipment. The distributor result identifies the amplifier as a mono, single-channel Class AB device, which is appropriate when the system processes one microphone channel rather than a stereo pair. The MAX4061EUA+ is supplied in an 8-uMAX/uSOP package according to the verified distributor result. The verified snippets do not provide the complete electrical parameter table, gain range, supply-voltage range, input impedance, noise density, or exact pin mapping. Those values must therefore be checked against the manufacturer datasheet before final circuit design. In particular, microphone bias voltage, gain-network design, supply sequencing, and shutdown control should be validated against the specific MAX4061EUA+ datasheet rather than inferred from similar family members. Typical applications include notebook microphones, PDA audio systems, portable audio devices, differential electret-microphone front ends, and compact microphone signal conditioning. The device's internal bias can simplify microphone front-end design compared with a discrete bias network, while its differential input arrangement can improve immunity to common-mode disturbance in a compact PCB. Complete shutdown can help reduce power consumption when the audio path is inactive, although the exact shutdown timing and current values are not present in the provided web data. For implementation, place the microphone input and amplifier compensation network close to the device, keep high-impedance microphone traces short, and provide local supply decoupling. Confirm the actual pinout and exposed-pad requirements from the manufacturer datasheet before layout release. This page combines the verified distributor identification, family-level manufacturer description, package information, pricing source, and application guidance while clearly identifying unavailable technical parameters rather than guessing them.
MAX4063ETE+ - Diff Mic Preamp, 2-Ch, 2.4-5.5V, TQFN-16 | Maxim
The Maxim Integrated (Analog Devices) MAX4063ETE+ is a 2-channel differential-input microphone preamplifier optimized for high-performance portable applications, integrating two selectable inputs, differential outputs, adjustable gain, an integrated low-noise microphone bias source, and a low-power shutdown mode. Housed in a 16-pin TQFN (4x4 mm) package, it operates from a single 2.4 V to 5.5 V supply, drawing only a few milliamps and dropping to sub-microamp shutdown current for battery-friendly operation. What is a microphone preamplifier? A microphone preamplifier is an analog front-end IC that boosts the very low-amplitude signal produced by an electret or MEMS microphone (typically 10-100 mV) up to line level suitable for an ADC or codec. It sits at the bottom of the audio signal chain: microphone capsule -> microphone preamplifier -> ADC or audio codec -> DSP/baseband. The MAX4063 specifically is a differential-input preamplifier, meaning it amplifies the difference between two input signals and rejects common-mode noise - critical for portable devices where ground loops and RF interference corrupt single-ended audio. Key features include differential inputs with high common-mode rejection, an internal low-noise bias voltage for electret microphones (eliminating the need for an external resistor divider), user-adjustable gain set by an external resistor, a complete shutdown mode for power savings, and a 2.4 V to 5.5 V wide single-supply operating range. The integrated bias source removes at least one or two external components compared to discrete designs, simplifying BOM and shrinking PCB area. Technically, the MAX4063 uses a low-noise op-amp topology optimized for audio bandwidth (20 Hz to 20 kHz), with high PSRR to reject supply ripple from upstream DC-DC converters. The differential architecture rejects RF and supply noise that would otherwise corrupt the microphone signal, and the internal bias source provides a clean regulated voltage to the electret capsule. Two selectable input paths allow the system to multiplex between two microphones (e.g., main mic and headset mic). Typical applications include notebook and tablet computer microphone arrays, headset microphones, Bluetooth headsets, digital cameras with audio capture, and any portable audio device requiring differential microphone amplification with EMI/RFI rejection. The shutdown mode extends battery life in always-listening voice-trigger designs. When designing with this device, place the input series resistors and AC-coupling capacitors close to the IC pins to maximize common-mode rejection. Use the internal bias source instead of an external resistor divider to reduce noise pickup and BOM count. The shutdown pin must be driven logic-high for normal operation and logic-low to enter shutdown. This page synthesizes drop-in alternatives, design considerations, and comparison data not found in the standalone manufacturer datasheet, supporting faster component selection for portable audio designs.
MAX4490AUK+T - 10MHz, 10V/us Rail-to-Rail Op Amp | Analog Devices
The Analog Devices MAX4490AUK+T is a single, low-cost CMOS operational amplifier featuring a 10 MHz gain-bandwidth product, a 10 V/us slew rate, and rail-to-rail input and output operation in a 5-pin SOT-23 package. It operates from a single +2.7 V to +5.5 V supply or from dual ±1.35 V to ±2.75 V supplies, making it suitable for compact, low-voltage analog and mixed-signal designs. An operational amplifier, or op amp, is an active analog integrated circuit that amplifies the difference between two input voltages. The MAX4490 belongs to the rail-to-rail input/output amplifier family, allowing its input and output voltages to approach the supply rails. This makes it useful when the signal range and output swing requirements exceed the practical limits of conventional amplifier architectures. Key verified features include a 10 MHz gain-bandwidth product and a 10 V/us slew rate. The device can drive 2 kOhm resistive loads to within 55 mV of either supply rail and remains unity-gain stable. Its single 5-pin SOT-23 package supports space-constrained designs, while its low-cost positioning helps reduce BOM cost in production. The MAX4490AUK+T is built around a CMOS operational-amplifier architecture designed for low-voltage operation and broad input/output range. Its 10 MHz bandwidth supports signal conditioning at moderate frequencies, while the 10 V/us slew rate improves large-signal response. Rail-to-rail output capability is especially useful in battery-powered systems, sensor interfaces, and low-voltage audio or control circuits. Typical applications include portable instrumentation, sensor signal conditioning, audio preamplification, low-voltage data acquisition, and general-purpose analog control. The 2.7 V minimum single-supply operation supports designs powered from 3.3 V rails, while the 5.5 V maximum supports common 5 V systems. Designers should verify the exact pinout and package variant, maintain adequate supply bypassing, and account for the 55 mV output headroom specification when driving loads near either rail. Because the MAX4490 is listed by the manufacturer as LAST TIME BUY, sourcing plans and long-term availability should be confirmed before new production commitments.
MAX942CUA+T - 80ns High-Speed 3V/5V Comparator | Maxim
The Analog Devices / Maxim Integrated MAX942CUA+T is a single high-speed, low-power comparator optimized for 3V or 5V single-supply systems, housed in an 8-pin µMAX (uSOP) package. It combines 80 ns propagation delay with only 3 mA supply current per comparator and true rail-to-rail inputs that extend 200 mV beyond the rails. The CMOS push-pull / TTL-compatible output stage eliminates the need for an external pull-up resistor and swings rail-to-rail on the output side as well. A comparator is an analog decision-making element that compares two input voltages and drives its output to one of two saturated states; it is the 1-bit ADC of the analog domain, often used to translate an analog level into a digital logic edge for a microcontroller, ASIC, or FPGA. Comparators sit in the broader linear IC hierarchy: analog building block -> op-amp/comparator -> high-speed comparator -> rail-to-rail input comparator -> single-supply part. The MAX941/MAX942/MAX944 family from Maxim occupies the 3V/5V rail-to-rail comparator node of that hierarchy and is widely cited as the reference for low-power, fast-responding comparators in commercial-grade designs. Key features of the MAX942 include a 3 mV typical input offset voltage, 150 nA typical input bias current, 80 ns propagation delay, 3 mA supply current per comparator, push-pull CMOS/TTL-compatible output, and operation from 2.7 V to 5.5 V. It is specified over the 0 °C to +70 °C commercial temperature range in the MAX942CUA+T (uSOP-8) variant and is offered in tape-and-reel packaging with the +T suffix. The MAX942 uses a standard high-speed comparator architecture with input ESD-protection diodes, a low-offset input stage, and a CMOS push-pull output driver. The rail-to-rail input stage uses an N-channel / P-channel complementary differential pair that switches automatically as the common-mode voltage crosses the mid-supply region, preserving low distortion across the entire input range including 200 mV beyond VCC and GND. The push-pull output swings within millivolts of both rails for direct interfacing to 3V/5V CMOS logic. Typical applications include window detectors, threshold detectors, zero-crossing detectors, A/D front-ends, and line receivers in portable, industrial, and instrumentation equipment. Because the inputs remain linear 200 mV beyond both rails, the MAX942 is well suited to monitor a 5 V rail with a 5.5 V reference or to sense signals near ground with a single-supply design. When designing with this part, observe the absolute-maximum input current limit on the input ESD diodes and add a series resistor if a large overdrive is expected. The push-pull output cannot be wire-ORed with other open-drain outputs - if a shared interrupt line is needed, choose the open-drain MAX941 instead.
MAX9611AUB+ - 12-Bit High-Side Current-Sense Amplifier | Analog Devices
The Analog Devices MAX9611AUB+ is a high-side current-sense amplifier with an integrated 12-bit ADC and a configurable op amp or comparator gain block, operating from a 0V to 60V input common-mode range and offered in a 10-pin uMAX package. A high-side current-sense amplifier is an analog measurement IC that develops a voltage proportional to the current passing through a sense resistor placed in a supply or power rail. It belongs to the current-sense amplifier hierarchy within signal-chain and power-management semiconductors. By measuring voltage across a small shunt, the device enables current monitoring, protection, diagnostics, and feedback without interrupting the high-side load path. Key verified features include a 0V to 60V input common-mode range, programmable full-scale voltages of 440mV, 110mV, and 55mV, a 12-bit ADC, and 2.5MHz bandwidth identified in distributor product data. The MAX9611AUB+ uses the noninverting configuration identified by Analog Devices. Its integrated ADC supports digital current measurement, while the gain block can support comparator-style threshold functions according to the device documentation. The combination of a wide common-mode range and selectable full-scale voltage allows the sense resistor to be selected for the expected current range. This is useful when current measurements must operate across automotive, industrial, or power-supply rails while preserving measurement resolution. The 60V capability also exceeds the nominal range of many low-voltage signal-chain amplifiers, allowing the part to remain on a higher-voltage high-side rail. Typical applications include motor and actuator current monitoring, battery-pack current sensing, industrial power-system protection, DC-DC converter feedback, and automotive load diagnostics. The noninverting MAX9611 is appropriate when the measured output polarity and system architecture match the target board. Designers should verify the sense-resistor value, full-scale setting, ADC reference, Kelvin routing, filtering, and thermal dissipation before production. The manufacturer’s application guidance and datasheet should control the final values because the provided source data does not include all timing, accuracy, and electrical limits. This page consolidates verified manufacturer and distributor information, explains practical current-sense design choices, and distinguishes documented alternatives from unverified package substitutions. Unspecified values are explicitly marked for engineering follow-up rather than estimated.
MAX9744ETH+ - 20W Stereo Class D Audio Amp | Maxim Integrated
The Maxim Integrated MAX9744ETH+ is a 20W per-channel stereo Class D audio power amplifier housed in a 44-pin TQFN (7x7 mm) exposed-pad package. It combines Class AB audio performance with Class D efficiency, eliminating the need for a bulky heatsink while delivering up to 22.5W output power into 4Ω loads from a single 4.5V to 14V supply. A Class D audio amplifier is a switching amplifier topology that uses high-frequency pulse-width modulation (PWM) to drive the output stage. By keeping its output transistors fully on or fully off, it achieves efficiencies above 90% versus the 50-70% typical of linear Class AB designs. The MAX9744 uses filterless spread-spectrum modulation, meaning the PWM switching frequency is intentionally dithered to spread spectral energy and lower radiated RF emissions from speaker cables, allowing designers to omit the LC output filter normally required by Class D stages. Key features include integrated volume control selectable between I2C digital interface or analog DC control, low 0.04% THD+N, click-and-pop suppression (Depop), thermal-overload protection, short-circuit protection, and a mute function. The device operates from a single 4.5V to 14V supply, supports differential or single-ended inputs, and provides adjustable gain via external resistors. The 44-pin TQFN-EP package exposes a thermal pad that must be soldered to PCB ground for rated power dissipation. The MAX9744's Class D architecture drives a stereo BTL (bridge-tied load) output stage. Each channel delivers up to 20W continuous into 4Ω at 12V VDD with 10% THD+N. Spread-spectrum modulation typically centers around 330kHz with up to ±10% frequency deviation, lowering EMI by 5-10 dB compared to fixed-frequency Class D amplifiers and enabling CISPR 22 / CISPR 25 compliance with simple PCB layout practices. Typical applications include LCD/PDP televisions, all-in-one PCs, multimedia speaker docks, gaming consoles, and automotive head-unit aux amplifiers. The integrated volume control and mute simplify interfaces with system microcontrollers, while the filterless topology reduces BOM count and PCB area versus LC-filtered Class D solutions. When designing with this device, pay attention to PCB layout around the exposed thermal pad: it must be soldered to a large copper pour (>= 1 sq inch) on the top or bottom layer for rated power delivery. Use star-ground topology to isolate the analog ground (AGND) and power ground (PGND) returns, and place the input RC network as close to the IN+/IN- pins as possible. This page synthesizes distributor pricing, drop-in alternatives, application context, and practical design notes not found in the standalone manufacturer datasheet.
MAX9814ETD+T - Mic Amplifier with AGC | Analog Devices
The Analog Devices MAX9814ETD+T is a low-cost, high-quality microphone amplifier with automatic gain control (AGC) and a low-noise microphone bias generator, housed in a 14-pin TDFN (3x3 mm) surface-mount package. It integrates a low-noise preamplifier, a variable-gain amplifier (VGA), an output amplifier, a microphone bias-voltage generator, and AGC control circuitry in a single IC, and operates from a 2.7V to 5.5V single supply. According to the Maxim datasheet, the device targets portable and consumer audio applications where dynamic range, size, and BOM cost all matter. A microphone preamplifier is the front-end analog stage that boosts a microphone's small output signal to a usable line level before ADC or codec digitization. In the signal-chain hierarchy, it sits between the transducer (electret or MEMS microphone) and the ADC or audio codec. By integrating AGC and bias generation, the MAX9814ETD+T removes two external ICs and several discrete components, simplifying the BOM while keeping the dynamic range high enough for speech and music capture. Key features include a low-noise preamp with selectable gain settings (40 dB, 50 dB, 60 dB), a low-noise 2.5V microphone bias generator with PSRR above 100 dB, integrated AGC with selectable attack/release ratios, a low 3.7 mA supply current, and a <1 uA shutdown mode. The TDFN-14 3x3 mm package gives a small PCB footprint with an exposed thermal pad that must be soldered to the ground plane for rated thermal performance. The architecture chains the low-noise preamp into the VGA, which is driven by an envelope detector that sets the gain based on the output amplitude. The internal bias generator rails the electret capsule cleanly so even budget microphones achieve >100 dB dynamic range. Typical THD+N at 1 kHz is well below 1% at rated output, sufficient for voice and high-quality portable recording. Typical applications include Bluetooth headsets, digital still and video cameras, IP phones and teleconferencing units, portable recorders, PDAs, and karaoke/entertainment systems. The wide 2.7V-5.5V input range covers a single Li-ion cell (3.0V-4.2V) plus USB-powered 5V designs. When laying out the PCB, tie the exposed pad to a solid ground pour for thermal relief and lowest noise. Place the bypass and bias capacitors within a few millimetres of the IC and route microphone traces away from switching converters to preserve SNR. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping audio engineers shorten their BOM evaluation and speed time-to-market.
MAX98357AETE+T - 3.2W PCM Class D Amp | Analog Devices
The Analog Devices (Maxim Integrated) MAX98357AETE+T is a tiny, low-cost, digital pulse-code modulation (PCM) input Class D audio amplifier that delivers industry-leading Class AB audio performance with Class D efficiency, packed in a 16-pin TQFN (3x3 mm) package with exposed pad. What is a Class D amplifier? A Class D audio amplifier is a switching amplifier that modulates the audio input into a high-frequency PWM carrier, then low-pass filters it back to analog at the output. Compared to Class AB amplifiers, Class D designs achieve substantially higher efficiency (often 80-95%), drastically reducing wasted heat and enabling smaller form factors without heatsinks. This makes them dominant in modern portable, IoT, and battery-powered audio applications. Key features include 3.2W output power into a 4 ohm load, 77dB PSRR, and 92% efficiency into 8 ohms. The device supports 2.5V to 5.5V supply operation with only 2.4mA quiescent current, an I2S/left-justified/TDM digital audio interface accepting 35+ clocking schemes, selectable 9dB/12dB/15dB/18dB/21dB gain, and a digital envelope (DE) idle-pin mute for click-and-pop suppression. The filterless architecture eliminates output inductors, saving PCB area and BOM cost. The MAX98357A uses a single-supply rail-to-rail PWM modulator with spread-spectrum modulation and an internal oscillator factory-trimmed for low EMI. Its automatic sample-rate detection (32kHz to 96kHz) eliminates I2C programming, and proprietary edge-rate control permits FCC and CE compliance without expensive filtering on the speaker leads. Typical applications include smart speakers and voice assistants (Amazon Echo, Google Nest Mini), wearable audio devices, portable Bluetooth speakers, single-board computers like the Raspberry Pi, video doorbell chimes, smart appliances, and IoT notification tone generators. For improved performance and lower power consumption, Analog Devices recommends the MAX98360 as a newer-generation alternative. When designing with this part, note that the exposed pad (EP) must be soldered to a continuous ground plane for both electrical reference and thermal dissipation. Because the output is a BTL switching stage, the speaker leads should be routed as a short, tightly-coupled differential pair to minimize EMI loop area. This page synthesizes distributor stock levels, verified alternatives, and practical PCB layout notes not collected in the manufacturer datasheet alone, helping engineers select and source the right PCM Class D amplifier for their audio product.
MAX98740BENL+TG7 - Low-EMI Class D Audio Amplifier IC
The Analog Devices (formerly Maxim Integrated) MAX98740BENL+TG7 is a high-efficiency, low-EMI Class D audio amplifier IC that integrates boost converter functionality in a compact 16-bump WLP package. It delivers up to 2.45W of output power into an 8 ohm load from a single lithium-ion (Li+) battery input, making it well suited for portable mono audio applications. The device combines a filterless Class D output stage with a synchronous-rectification boost converter to maintain output voltage headroom across the full Li+ discharge curve. A Class D audio amplifier (also called a switching amplifier) is a type of power amplifier that uses pulse-width modulation (PWM) at high frequency (typically 250 kHz to 2 MHz) to drive the output stage, achieving efficiencies above 90% compared to 50-65% for traditional Class AB amplifiers. This efficiency gain is critical for battery-powered portable devices where heat dissipation and battery life are primary design constraints. Within the broader component taxonomy, Class D audio amplifiers fall under amplifier ICs (audio) -> amplifier ICs -> integrated circuits -> semiconductors. Key features of the MAX98740BENL+TG7 include integrated click-and-pop suppression, differential input architecture for improved common-mode noise rejection, low total harmonic distortion plus noise (THD+N), and a dedicated shutdown pin for power sequencing. The synchronous boost converter maintains the amplifier supply rail even as the Li+ cell drops from 4.2V to 3.0V, preserving audio output level across the entire discharge cycle. The device operates from a single 2.7V to 5.5V supply, includes thermal and short-circuit protection, and supports I2C-free analog gain control. The WLP-16 (Wafer-Level Package, 1.66 mm x 1.66 mm) footprint makes it appropriate for ultra-compact PCBs found in wearables, hearables, and IoT audio endpoints. The +TG7 suffix indicates tape-and-reel packaging with 7-inch reels. Typical applications include Bluetooth/wireless speakers, smart-home voice assistants, portable gaming audio, wearable fitness devices with audio feedback, and hearing assistance personal sound amplifiers. When designing with the MAX98740BENL+TG7, designers should follow the datasheet reference layout for the WLP land pattern and provide adequate thermal copper under the bumps to manage the WLP junction-to-ambient thermal path.
MAX9919NASA+T - ±75V Bidirectional Current-Sense Amp | Analog Devices
The Analog Devices MAX9919NASA+T is a single-supply, high-accuracy bidirectional current-sense amplifier with an input common-mode range that extends from -20 V to +75 V, housed in an 8-pin SOIC-EP (exposed-pad) package. Key headline specifications include a maximum input offset voltage of 400 uV, a maximum gain error of 0.6 %, a fixed gain of 90 V/V, and operation from a single 5 V supply. A current-sense amplifier is a specialized analog building block that measures the small differential voltage across a shunt resistor in the presence of a large common-mode voltage, converting that differential signal to a ground-referenced output proportional to load current. Within the broader taxonomy, the MAX9919 belongs to the instrumentation amplifier family, sits under the special-purpose amplifier category, and connects upward to the power-management and signal-conditioning IC hierarchy used in motor-drive, solenoid-drive, and battery-monitoring systems. Key differentiating features of the MAX9919 include the very wide -20 V to +75 V input common-mode range, support for unidirectional or bidirectional current measurement, 400 uV maximum input offset voltage for high DC accuracy, 0.6 % maximum gain error, and operation from a single 4.5 V to 5.5 V supply. The architecture uses a precision input pair and integrated gain resistor network, eliminating the requirement for external precision resistors in most applications. The device covers three variants in the same SOIC-EP footprint: the MAX9918 (low-bandwidth, unidirectional), the MAX9919 (bidirectional 90 V/V), and the MAX9920 (high-bandwidth, unidirectional). Selection between them is by application topology - bidirectional H-bridge current sensing on the MAX9919, simple high-side monitoring on the MAX9918/MAX9920. Typical applications include H-bridge motor current sensing, electronic throttle control, transmission control current monitoring, high- and low-side current sensing in 48 V automotive rails, and precision high-voltage current monitoring for industrial PLCs. Design consideration: the input common-mode range of -20 V to +75 V allows the device to survive load-dump transients and inductive kickback without protection diodes in many 12 V and 24 V automotive systems. The exposed pad must be soldered to the PCB ground plane for thermal dissipation; without a soldered EP the part exceeds the absolute maximum ratings at high load current. This page synthesizes distributor pricing, drop-in same-family and cross-brand alternatives, and design notes not found in the standalone manufacturer datasheet.
MC1430G - Low-Offset Amplifier, 33V/us | Motorola
The Motorola MC1430G is a single-circuit general-purpose operational amplifier with a 10 mV input offset voltage, 33 V/us slew rate, 75 dB common-mode rejection, and low 15 uA input bias current. The verified component data identifies a -9 V to +9 V supply range, a 0 °C to +70 °C commercial operating range, and 9.2 mA supply current. Distributor listings classify the device as a metal-can instrumentation or general-purpose amplifier. An operational amplifier is a voltage-gain stage that compares its inverting and non-inverting inputs. The difference between those voltages is amplified by a very high open-loop gain and then conditioned to drive the intended external feedback network. In the broader semiconductor hierarchy, the MC1430G belongs to the operational-amplifier, analog-amplifier, linear-amplifier, and analog IC families. It is intended for applications requiring signal amplification rather than power conversion or logic operation. The principal verified performance parameters include a 10 mV input offset voltage, 15 uA input bias current, 400 nA input bias-current variation, 33 V/us slew rate, 75 dB common-mode rejection, and 9.2 mA supply current. The 10 mV offset establishes the practical dc error that must be considered in precision signal chains. The 33 V/us slew rate limits how quickly the output can follow a changing input, while 75 dB common-mode rejection reduces the output response to voltage applied simultaneously to both inputs. MC1430G operates from -9 V to +9 V and supports a 0 °C to +70 °C temperature range. These limits place it in the traditional bipolar, dual-supply general-purpose amplifier class. Its metal-can construction reflects an older package family used for through-hole and panel or chassis-style applications. The verified distributor descriptions consistently identify one amplifier circuit and a metal-can package, although the available listings express the package designation inconsistently. Typical uses include low-level instrumentation, feedback stages around transducers, analog signal conditioning, and general-purpose voltage amplification. In a practical circuit, the amplifier should be configured with suitable negative feedback, supply bypassing, and output loading appropriate for the required signal bandwidth. The MC1430G can be used where a 33 V/us slew rate and 75 dB common-mode rejection are sufficient, but its 10 mV offset may make it less attractive than a lower-offset precision amplifier in high-gain dc measurement systems. Designers should verify the exact physical lead numbering and package dimensions against the manufacturer datasheet before PCB layout or replacement work. The available verified data does not expose a complete pin map, and the distributor records refer to metal-can and TO-100-style descriptions inconsistently. Power-supply bypassing, input common-mode range, output swing, bias-current compensation, and stability with the selected feedback network also require confirmation before production release. This page consolidates the verified distributor specifications, sourcing information, package ambiguity, and selection guidance for the MC1430G. It also separates directly verified data from fields that still require manufacturer-datasheet confirmation, helping engineers avoid treating generic cross-reference pages as proof of pin-to-pin compatibility.
MC1436CD - ±36V Internally Compensated Op Amp | Motorola
Motorola MC1436CD is a single-amplifier, general-purpose operational amplifier designed for high-voltage signal chains, with a specified supply range of ±36 V and internally compensated operation. The device is available in an 8-pin SOIC package, making the MC1436CD suitable for industrial, instrumentation, feedback-control, summing, and integration circuits where a conventional low-voltage operational amplifier cannot tolerate the required supply voltage. Its internally compensated architecture simplifies closed-loop design because the manufacturer identifies the MC1436 family as suitable for summing-amplifier, integrator, and external-feedback applications. The MC1436 belongs to the operational-amplifier hierarchy, where an operational amplifier is a differential-input voltage-amplifier IC used to amplify, buffer, sum, or integrate signals. An internally compensated operational amplifier integrates the frequency-compensation network, reducing the number of external components required for stable negative-feedback operation. The MC1436CD consequently sits between generic amplifier functions and precision signal-conditioning applications, while its ±36 V rating distinguishes it from common ±5 V, ±12 V, and ±15 V amplifier families. The verified product information identifies the MC1436 as a high-voltage, internally compensated operational amplifier intended for operation with external feedback components. This architecture supports conventional inverting and non-inverting amplifier configurations, active summing networks, and closed-loop integrators. Because the exact gain-bandwidth, slew-rate, input-offset, bias-current, input-common-mode-range, and output-swing limits are not included in the supplied source snippets, designers must consult the complete four-page MC1436CD datasheet before fixing loop gain, compensation, noise, accuracy, and stability margins. Typical industrial uses include process-control loops, high-voltage sensor interfaces, laboratory instrumentation, analog summing and averaging circuits, and active integrators. Its 8-pin SOIC format also supports compact surface-mount assemblies, although exposed-pad thermal analysis is not applicable because the specified package has no stated exposed thermal pad. Designers should still provide adequate copper and consider nearby heat sources because dissipation rises as supply voltage and output current increase. A key design consideration is to verify the complete DC and AC parameter set before replacing the amplifier with a lower-voltage modern part. The ±36 V supply capability is the principal differentiator, but stability, common-mode range, output swing, slew rate, and offset behavior determine whether a substitute is truly interchangeable. The available MC1436CD documentation is a four-page datasheet; no revision number or additional document number is established by the supplied data. This page consolidates verified distributor identification, package information, high-voltage operation, application positioning, cross-reference findings, and practical selection guidance. It also distinguishes documented facts from parameters that still require confirmation from the complete manufacturer datasheet, supporting faster sourcing without obscuring design-critical uncertainties.
MC14577CP - Dual Video Amplifier | Motorola | DIP-8
The Motorola MC14577CP is a dual video amplifier integrated circuit packaged in an 8-pin DIP. The device is listed for video amplifier and related signal-processing applications, and distributor listings identify it as a two-channel video amplifier with the package designation 8-PDIP. The MC14577CP is therefore primarily intended for applications requiring two video signal channels in a conventional through-hole package. A video amplifier is an analog integrated circuit used to condition composite, differential, or other video signals before they reach a display, monitor, video processing block, or transmission circuit. In the broader electronics hierarchy, the MC14577CP belongs to the class of amplifier ICs, specifically video amplifiers and modules, rather than being a discrete transistor or a general-purpose digital interface IC. Its dual-channel architecture can reduce the number of separate amplifier packages required in equipment that carries two related video signals. The MC14577CP is associated with the Motorola MC14577 video-amplifier family and is commonly encountered in legacy television, monitor, video-peripheral, and service-equipment designs. The 8-PDIP format makes the device convenient for through-hole prototypes, repair work, and equipment where a leaded package is preferred over a surface-mount package. The “CP” suffix identifies this particular ordering variant and should be retained when comparing it with other family members. Because the device is an older video amplifier, design work should begin with the manufacturer datasheet and the system’s signal levels, impedance requirements, bandwidth expectations, supply arrangement, and allowable distortion. The MC14577CP may be especially relevant when maintaining or reproducing older analog video hardware rather than designing a new compact surface-mount product. The key engineering question is whether the original board requires the MC14577CP’s channel count, gain behavior, supply voltage, input/output impedance, and output-drive capability. In a typical video path, the MC14577CP would sit between a video source and downstream circuitry, with external resistors and capacitors setting gain, bandwidth, coupling, or compensation as required by the application. Its through-hole package supports straightforward prototyping, but designers should still observe the datasheet’s decoupling and grounding recommendations to avoid instability, excessive noise, or channel-to-channel interaction. This product summary combines package and category information with practical replacement guidance. Because equivalent availability is limited, engineers should verify the pinout, electrical limits, and signal-chain requirements directly against the MC14577CP datasheet before substituting any part. For current commercial availability, use the Request a Quote form on this page rather than relying on historical distributor pricing.
MC14578P - CMOS Micro-Power Comparator + Voltage Follower | NXP Semiconductors
The NXP Semiconductors MC14578P is a CMOS analog building block that integrates a very-high-input-impedance comparator, a voltage follower, and four enhancement-mode MOSFETs (N-channel and P-channel pairs) on a single die, housed in a 16-pin PDIP (DIP-16) through-hole package. The MC14578 is a micro-power comparator with integrated voltage follower. An LDO (Low-Dropout) linear regulator maintains a stable output voltage, but the MC14578 belongs to a different category - it is a CMOS analog comparator designed for ultra-low-power signal conditioning in battery and line-powered applications. The integrated voltage follower allows monitoring the noninverting input of the comparator without loading the source, which is critical in high-impedance sensor interfaces where the comparator would otherwise distort the signal. The four on-chip MOSFETs (two N-channel and two P-channel) provide design flexibility for level shifting, switching, or simple analog front-ends around the comparator output. Key features include the analog building-block topology that combines comparator, follower, and discrete MOSFETs on one chip, an extremely low quiescent current suitable for battery-powered designs, a CMOS process that delivers very high input impedance, and a single-supply operation that simplifies integration with digital logic. Architecture-wise, the device uses a CMOS process that delivers very high input impedance on the comparator inputs and very low quiescent current consumption, a specification critical for battery-powered designs such as smoke detectors that must operate for years on a single 9V cell. The four co-integrated MOSFETs are positioned as auxiliary building blocks, allowing the designer to build simple transistor circuits around the comparator without external discretes. The combination of the high-impedance follower buffer and on-die MOSFETs is unusual in this package class and is the main architectural reason the part has been a long-term staple in low-cost smoke-detector and sensor-interface designs. Typical applications include line-powered smoke detectors, threshold detectors, liquid/moisture sensors, low-battery detectors, CO detectors and micro interfaces, and pulse shapers. The on-chip MOSFETs simplify typical battery-operated detector front-ends that otherwise would require several discrete transistors. One key design consideration: the on-chip MOSFETs have limited drain current and should not be used as primary power switches - they are sized as signal-path elements. Engineers should review the datasheet's continuous-drain current rating before driving relays or LEDs directly off these transistors. This page synthesizes distributor stock data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet itself.
MC1458D - Dual 1MHz Op Amp, ±15V, 8-SOIC | Texas Instruments (Tape & Reel)
The Texas Instruments MC1458D is a dual general-purpose operational amplifier integrating two internally compensated op amps in an 8-pin SOIC (D) package, originally designed to be pin-compatible with the classic Motorola MC1458 and Signetics N5558/S5558 parts. Each channel delivers a gain bandwidth product of 1 MHz with a 0.5 V/us slew rate and operates from split supplies of plus/minus 5 V to plus/minus 15 V, or equivalently from a single supply of 10 V to 30 V. The output stage swings within a few volts of each rail, and the inputs cover the full common-mode range including the negative rail, which simplifies single-supply signal-conditioning designs. An operational amplifier (op amp) is a high-gain DC-coupled voltage amplifier with differential inputs and a single-ended output. In the system hierarchy, the MC1458D sits as a general-purpose linear IC under amplifier ICs, which itself belongs to the broader family of analog signal-conditioning components and integrated circuits. The MC1458D is specifically a dual-channel, internally compensated design that requires no external frequency-compensation capacitor, simplifying PCB layout versus discrete-transistor op-amp implementations. Key features include short-circuit protection on the output stage, low power consumption of approximately 1.7 mA per amplifier at plus/minus 15 V, no latch-up, and wide common-mode plus differential voltage ranges. The two channels share a single bias network, giving matched DC behavior that suits difference amplifiers, active filters, and dual-channel transducer signal chains. Each channel is a complete bipolar op amp with internal compensation, allowing the part to be used as a direct functional replacement for legacy 1458-family designs with no circuit changes. Architecturally, the MC1458D uses a classic bipolar transistor input stage with an active load, a Darlington intermediate stage, and a class-AB complementary emitter-follower output, mirroring the topology of the uA741 but with two channels on one die. The dual-die design eliminates the need for an external compensation capacitor on each channel; instead, the internal capacitor is trimmed during wafer test. This mature architecture trades raw speed for excellent DC accuracy, low input bias current relative to JFET alternatives, and predictable behavior over the full 0 to 70 degrees C commercial temperature range. Typical applications include active filtering, transducer signal conditioning, instrumentation front ends, integrators and comparators, audio preamplifiers, and general-purpose dual-channel amplification in industrial controls and consumer electronics. The matched pair also makes it well-suited for differential amplifiers driving downstream ADCs. When designing with this part, observe the absolute maximum differential input voltage of plus/minus 30 V and ensure the input common-mode range is respected to avoid phase inversion. Bypass supplies with a 0.1 uF ceramic capacitor close to the VCC+ and VCC- pins to prevent oscillation in unity-gain buffer configurations. This page synthesizes distributor pricing, drop-in replacement candidates for the dual 1458 pinout, and practical design notes not consolidated in the manufacturer datasheet.
MC1458DE4 - Dual 1 MHz Op Amp | Texas Instruments
Texas Instruments MC1458DE4 is a dual general-purpose operational amplifier with two independently usable amplifier circuits, a 1 MHz gain-bandwidth product, and a 0.5 V/µs slew rate. The device is packaged in an 8-pin SOIC measuring 0.154 inch, or 3.90 mm, in width. It is intended for general-purpose analog signal conditioning and is described as a dual operational amplifier whose internal frequency compensation eliminates the need for external compensation components. An operational amplifier, or op amp, is a voltage-gain building block within analog and mixed-signal electronics. MC1458DE4 belongs to the general-purpose operational-amplifier class and contains two amplifier channels in one package. Its internally compensated architecture simplifies circuit construction in voltage followers, summing amplifiers, comparators, and general signal-conditioning networks. The two channels can process different analog signals or can be used together for filtering, instrumentation, and differential circuit functions when the application requires it. Key characteristics include two amplifier circuits, a 1 MHz gain-bandwidth product, a 0.5 V/µs slew rate, a 15 V supply designation, and integrated frequency compensation. The manufacturer describes the amplifier as low-power, protected against latch-up, and intended for voltage-follower use. Unlike implementations that expose offset-null terminals, the MC1458 family is described as having each amplifier half electrically similar to a µA741 without offset-null capability. The absence of those terminals simplifies the pin assignment and reduces external component count. The internally compensated amplifiers provide stable operation in voltage-follower configurations without external frequency-compensation networks. Their approximately 1 MHz bandwidth is suitable for audio-frequency and general instrumentation signal paths where moderate bandwidth is sufficient. The 0.5 V/µs slew rate determines how rapidly output voltage can follow a changing input, making the device appropriate for general analog amplification rather than high-speed pulse or wideband signal processing. Typical uses include audio preamplification, summing and averaging amplifiers, voltage followers, sensor signal conditioning, comparator-style threshold circuits, and educational or laboratory analog designs. The 8-pin SOIC package allows two amplifier channels to be placed on a compact through-hole PCB footprint, while the device's two-circuit organization can reduce component count when both positive and negative signals are processed. Designers should account for supply headroom, common-mode input range, output swing, and the bandwidth available at the selected closed-loop gain. Decoupling capacitors should be placed close to the supply pins, and sensitive analog layouts should minimize trace resistance and coupling from switching circuitry. The most important sourcing check is pinout and footprint compatibility, because different package suffixes of the MC1458 family can use different standard packages. This product page consolidates the MC1458DE4 electrical identity, package information, practical use cases, verified source links, and design guidance. It also distinguishes confirmed drop-in candidates from package or electrical variants, helping engineers evaluate replacements without assuming that a similar amplifier description guarantees a compatible PCB footprint.
MC1458DR - Dual 1MHz Op Amp, ±15V, 8-SOIC | Texas Instruments
The Texas Instruments MC1458DR is a dual general-purpose operational amplifier integrating two internally compensated op amps in an 8-pin SOIC (D) package, originally designed to be pin-compatible with the classic Motorola MC1458 and Signetics N5558/S5558 parts. Each channel delivers a gain bandwidth product of 1 MHz with a 0.5 V/us slew rate and operates from split supplies of plus/minus 5 V to plus/minus 15 V, or equivalently from a single supply of 10 V to 30 V. The output stage swings within a few volts of each rail, and the inputs cover the full common-mode range including the negative rail, which simplifies single-supply signal-conditioning designs. An operational amplifier (op amp) is a high-gain DC-coupled voltage amplifier with differential inputs and a single-ended output. In the system hierarchy, the MC1458DR sits as a general-purpose linear IC under amplifier ICs, which itself belongs to the broader family of analog signal-conditioning components and integrated circuits. The MC1458DR is specifically a dual-channel, internally compensated design that requires no external frequency-compensation capacitor, simplifying PCB layout versus discrete-transistor op-amp implementations. Key features include short-circuit protection on the output stage, low power consumption of approximately 1.7 mA per amplifier at plus/minus 15 V, no latch-up, and wide common-mode plus differential voltage ranges. The two channels share a single bias network, giving matched DC behavior that suits difference amplifiers, active filters, and dual-channel transducer signal chains. Each channel is a complete bipolar op amp with internal compensation, allowing the part to be used as a direct functional replacement for legacy 1458-family designs with no circuit changes. Architecturally, the MC1458DR uses a classic bipolar transistor input stage with an active load, a Darlington intermediate stage, and a class-AB complementary emitter-follower output, mirroring the topology of the uA741 but with two channels on one die. The dual-die design eliminates the need for an external compensation capacitor on each channel; instead, the internal capacitor is trimmed during wafer test. This mature architecture trades raw speed for excellent DC accuracy, low input bias current relative to JFET alternatives, and predictable behavior over the full 0 to 70 degrees C commercial temperature range. Typical applications include active filtering, transducer signal conditioning, instrumentation front ends, integrators and comparators, audio preamplifiers, and general-purpose dual-channel amplification in industrial controls and consumer electronics. The matched pair also makes it well-suited for differential amplifiers driving downstream ADCs. When designing with this part, observe the absolute maximum differential input voltage of plus/minus 30 V and ensure the input common-mode range is respected to avoid phase inversion. Bypass supplies with a 0.1 uF ceramic capacitor close to the VCC+ and VCC- pins to prevent oscillation in unity-gain buffer configurations. This page synthesizes distributor pricing, drop-in replacement candidates for the dual 1458 pinout, and practical design notes not consolidated in the manufacturer datasheet.
MC1458DR2 - Dual Internally Compensated Operational Amplifier | onsemi
The onsemi MC1458DR2 is a dual, internally compensated operational amplifier designed for general-purpose analog signal processing. It provides two amplifier circuits in an 8-pin SOIC package and is specified for operation from a single positive supply, making it suitable for audio, instrumentation, control, and active-filter applications. The device uses bipolar construction and is optimized for applications using external feedback components, including summing amplifiers, integrators, and conventional closed-loop amplifier stages. The MC1458 family combines a high-performance dual amplifier with internal frequency compensation. Internal compensation removes the need for an external dominant-pole capacitor in many standard feedback configurations, while external feedback resistors still determine gain, bandwidth, input impedance, and signal behavior. This makes the MC1458DR2 practical for designs that require a straightforward dual-amplifier solution rather than a highly integrated modern rail-to-rail amplifier. Key operating characteristics include low input offset voltage, low input bias current, broad common-mode input range, and a dual-amplifier configuration in a compact surface-mount package. The internal compensation is designed for stable operation with resistive feedback networks, allowing the device to be used in non-inverting, inverting, voltage-follower, summing, and active-filter circuits. The two amplifiers share a common power supply and ground connection while maintaining separate differential inputs and outputs. Typical uses include small-signal audio channels, sensor-conditioning stages, analog summing networks, waveform shaping, integrators, and low-frequency control loops. The 8-pin SOIC footprint is also convenient for designs that previously used 8-pin dual operational amplifiers. Because this is an older bipolar amplifier family, engineers should verify the exact supply voltage, common-mode range, output swing, slew rate, and input/output current limits against the manufacturer datasheet before finalizing a new design. For PCB design, place the device close to the feedback network and bypass pins, route high-impedance input and compensation-related nodes with short traces, and maintain a quiet ground reference. Decoupling capacitors should be positioned close to the supply pins, while analog input traces should be separated from switching and digital return paths. The dual architecture allows two related signal paths to be implemented with one package, reducing component count and simplifying board layout. This product page combines the manufacturer and distributor references, package information, technical use cases, comparison fields, and practical design guidance for engineers evaluating the MC1458DR2 as a dual operational-amplifier choice.
MC1458DT - High-Performance Dual Op Amp | STMicroelectronics
The STMicroelectronics MC1458DT is a high-performance, monolithic, dual operational amplifier with a wide input common-mode voltage range, supplied in an 8-pin SOIC package. The device contains two amplifiers and is intended for general-purpose analog signal-conditioning applications. Its high gain, wide operating-voltage range, and general feedback architecture support integrator, summing-amplifier, comparator-style, and precision feedback designs. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The MC1458 belongs to the operational-amplifier family, which is part of the broader analog IC and semiconductor hierarchy. Operational amplifiers are used wherever a circuit must amplify, buffer, filter, integrate, or compare a small electrical signal, making them foundational building blocks in instrumentation, control, communications, and consumer equipment. Key features of the MC1458 include its dual-amplifier configuration, high-performance monolithic construction, wide input common-mode voltage range, and low power consumption. The dual format allows two independent amplifier channels in one package, reducing board area and simplifying designs that require matched amplification stages. Its general-purpose feedback configuration makes it useful in both conventional closed-loop amplifier circuits and active analog networks. The MC1458 is specified for a wide range of operating voltages, which gives designers flexibility when using it with different supply rails and signal levels. The device is suitable for integrator and summing-amplifier applications because its high gain and feedback characteristics support accurate closed-loop operation. The manufacturer describes the MC1458 as intended for a wide range of analog applications rather than a single narrow use case. Typical applications include audio preamplification, sensor signal conditioning, analog filtering, instrumentation, general feedback control, and low-frequency analog signal processing. Its SOIC-8 package also makes it practical for conventional PCB assembly where dual-channel analog amplification is required. Designers should verify supply voltage, input common-mode range, output swing, stability, and load requirements against the manufacturer datasheet for the exact operating conditions. When designing around the MC1458DT, use appropriate input and output bypassing, keep feedback paths short, and verify that the selected operating point remains inside the device's electrical limits. This page combines the verified manufacturer and distributor information with practical selection guidance and drop-in cross-reference context for engineers evaluating the MC1458 family.
MC1458ID - Dual High-Performance Operational Amplifier | STMicroelectronics
The STMicroelectronics MC1458ID is a high-performance dual operational amplifier integrated circuit with two amplifier circuits in an 8-pin SOIC package. It is intended for general-purpose analog signal-processing applications, including summing amplifiers, voltage followers, integrators, active filters, and function generators. The device is identified as a low-noise, wide-temperature-range dual op amp with short-circuit protection and no frequency-compensation requirement. An operational amplifier is a voltage-feedback analog amplifier used to amplify the difference between two input voltages. In a feedback network, the MC1458ID can provide high closed-loop gain, signal buffering, impedance transformation, and active-filter functions. Its dual-circuit architecture places two independent amplifiers in one package, reducing board area when a design requires two analog signal channels. The MC1458ID is described as a high-performance monolithic dual operational amplifier with low power consumption and a large input-voltage range. The device also features high gain, short-circuit protection, no-latch-up behavior, and operation without frequency compensation. These characteristics make it suitable for instrumentation, audio signal processing, active filtering, summing and integrating circuits, and general analog control systems. The MC1458ID uses a conventional dual-amplifier architecture rather than a digitally controlled or precision-specialty amplifier. Its two channels are packaged in an 8-SOIC, allowing a compact surface-mount implementation. The wide operating-voltage capability supports varied analog supply conditions, while the low-noise designation is relevant to applications in which signal integrity and small-signal amplification matter. Typical uses include audio preamplification, instrumentation buffering, active filters, summing amplifiers, integrators, voltage followers, and function-generator circuits. In an instrumentation application, the device can buffer sensor outputs before conversion or further processing. In audio systems, one channel may process one signal path while the second handles another, provided the power supply and grounding arrangement support both circuits. When designing around the MC1458ID, use the manufacturer pin-description table to assign supply, input, and output connections, and observe the dual-amplifier decoupling requirements. Place bypass capacitors close to the supply pins, keep feedback-loop routing short, and check input and output signal limits against the device operating conditions before finalizing the board layout. This product page combines the STMicroelectronics MC1458ID device identity, package information, functional applications, sourcing structure, and practical design guidance to support faster component selection and board-level implementation.