Amplifier ICs
بەرهەمەکان (3,200+)
NE5534AN - 10MHz Low Noise Audio Op-Amp DIP-8 | onsemi
The onsemi NE5534AN is a single high-performance low-noise operational amplifier with a 10 MHz gain-bandwidth product, 13 V/us slew rate, and supply operation from 3 V to 20 V per rail, housed in an 8-pin plastic DIP (0.300 inch, 7.62 mm row spacing) through-hole package. Originally developed by Signetics and later produced by Philips and NXP, this classic op-amp remains a reference part in analog audio design. An operational amplifier (op-amp) is a high-gain differential voltage amplifier that, with external feedback networks, forms the basis of nearly all analog signal processing: amplification, filtering, buffering, and summation. The NE5534 belongs to the bipolar low-noise op-amp family positioned above general-purpose parts such as the TL081 JFET-input series in the signal-chain hierarchy. Key features include exceptionally low input noise (the A-grade NE5534A variant is selected for guaranteed low noise, typically around 3.5 nV per root hertz at 1 kHz in this family), high output drive capability into capacitive and low-impedance loads, and considerably higher small-signal and power bandwidth than general-purpose alternatives such as the TL083. Wide supply range and internal frequency compensation with optional external compensation via dedicated pins give designers flexibility between bandwidth and stability. Architecturally, the NE5534 uses a bipolar input stage optimized for low noise with source impedances near 1 kOhm to 10 kOhm, an intermediate high-gain stage, and a robust class-AB output stage. Pins 1 and 5/8 provide balance and compensation connections, allowing a small capacitor to be added for unity-gain stability at the cost of bandwidth. Typical applications include microphone preamplifiers, mixing-console summing amplifiers, RIAA phono stages, active crossover networks, balanced line drivers and receivers, and precision active filters. Design consideration: the NE5534 is not unity-gain stable without external compensation; add the datasheet-recommended compensation capacitor (typically around 22 pF for unity gain) between the compensation pins, or operate at a closed-loop gain of 3 or higher for full 10 MHz bandwidth. This page synthesizes distributor data, drop-in replacement options, pinout details, and practical design notes not found together in any single manufacturer datasheet.
NE5534ANG - Low-Noise Single Op Amp | onsemi | 8-PDIP
The onsemi NE5534ANG is a single high-performance, low-noise operational amplifier designed for professional audio, instrumentation, and control applications. It operates from a 3 V to 20 V supply, supports standard general-purpose amplifier use, and is supplied in an 8-pin PDIP package. The NE5534 family is noted for low-noise operation, improved output-drive capability, and higher small-signal and power bandwidth than conventional general-purpose amplifiers such as the TL083. An operational amplifier is an active analog building block that uses high-gain differential amplification with negative feedback to create stable, accurate gain in audio, measurement, filtering, and control circuits. The NE5534ANG belongs to the operational-amplifier, analog-amplifier, and signal-conditioning hierarchy. Its single-amplifier configuration makes it useful when one channel is required, while its low-noise and output-drive characteristics make it relevant to microphone preamplification, active filters, audio mixing, and precision analog signal chains. Key features include a single amplifier configuration, low-noise performance, strong output-drive capability, and improved small-signal and power bandwidth relative to older general-purpose amplifier families. The device is intended for high-quality professional audio equipment, where low circuit noise, adequate drive into downstream stages, and predictable frequency response are important. It is also suitable for instrumentation and control circuits where signal amplification must remain accurate across a range of source impedances. The NE5534ANG uses an internally compensated operational-amplifier architecture intended for closed-loop operation at gains of one or higher. Designers should preserve the recommended bypass and compensation practices shown in the manufacturer datasheet, especially when driving capacitive loads or operating near the limits of the supply voltage. Decoupling capacitors should be placed close to the power pins to reduce supply ripple coupling into the amplified signal. Typical uses include professional audio input stages, low-level microphone preamplifiers, active equalization filters, audio mixing and distribution, laboratory instrumentation, and general feedback-control circuits. The 8-pin PDIP package supports through-hole construction and is convenient for prototyping, repair, and conventional analog boards where a socketed single amplifier is preferred. For PCB layout, keep the input and output paths short, maintain a quiet ground reference around the amplifier, and avoid routing sensitive input traces beside high-current switching nodes. Verify the maximum input and output swing against the selected supply voltage before designing gain stages with limited headroom. This page combines manufacturer-device information with practical engineering guidance, application context, and qualified drop-in comparison points.
NE5534AP - 30V 10MHz Low-Noise Op Amp | Texas Instruments
Texas Instruments NE5534AP is a single low-noise operational amplifier for audio applications, with a 30 V maximum supply, 10 MHz unity-gain bandwidth, and a PDIP-8 package. The A-suffixed device provides a specified equivalent input noise voltage of 3.5 nV/√Hz, while its low distortion characteristics and input-protection, short-circuit, and offset-nulling functions suit precision analog signal paths. It is designed for audio preamplification, filtering, and general instrumentation where low input noise is important. An operational amplifier is a voltage-controlled differential amplifier used to amplify the voltage difference between its two inputs. Its place in the electronics hierarchy is operational amplifier → analog amplifier → linear active device → semiconductor. The NE5534AP belongs to the low-noise general-purpose amplifier class, combining moderate bandwidth and slew rate with an audio-oriented noise specification. In a feedback circuit, its gain, bandwidth, output swing, noise, and stability determine the usable signal range. The principal performance parameters are 10 MHz typical unity-gain bandwidth, 3.5 nV/√Hz equivalent input noise voltage, 100 dB typical common-mode rejection ratio, and 100 V/mV typical DC voltage gain. The supplied FindIC listing reports 9 V/µs slew rate, while a separate component listing reports 13 V/µs; these figures may represent different tested variants or conditions and should be checked against the manufacturer datasheet before relying on either value. A 32 V typical peak-to-peak output swing is listed at ±18 V supplies. Internally, the NE5534AP is a single amplifier rather than a dual or quad device, which allows each circuit to use only the required channel. Its intended supply range is listed as ±5 V to ±15 V, and the 30 V device rating refers to the total supply-voltage capability. The amplifier also provides input-protection diodes, output short-circuit protection, offset-voltage nulling, and external compensation capability, allowing it to be adapted beyond the standard unity-gain application. Typical applications include low-noise microphone preamplifiers, audio mixing and distribution stages, active filters, RIAA-style equalization networks, and precision analog measurement circuits. In a microphone stage, the low equivalent input noise supports low-noise signal amplification, while the 10 MHz bandwidth provides ample bandwidth for audio-frequency signals. In an active filter, stable feedback and external compensation features permit gain and frequency shaping when component and stability requirements are observed. Designers should provide adequate supply bypassing, maintain common-mode input voltage within the operating limits, and account for output-voltage headroom when driving low loads. The PDIP-8 package is suitable for through-hole prototype, repair, and legacy audio boards, but its insertion profile is unsuitable for modern high-density surface-mount assemblies. Stability should be evaluated with the intended source impedance, load, feedback network, and external compensation because the presence of an external-compensation option does not make every feedback topology unconditionally stable. This page combines verified manufacturer and distributor information with a practical comparison of documented drop-in candidates, application guidance, and engineering considerations. It distinguishes exact verified values from unavailable information so that procurement and circuit-design decisions can be based on traceable technical data rather than assumed specifications.
NE5534D - 30V, 10MHz Low-Noise Audio Op Amp | Texas Instruments
The Texas Instruments NE5534D is a single, low-noise operational amplifier for audio applications, with a 30 V maximum total supply rating, 10 MHz typical unity-gain bandwidth, and an 8-pin SOIC package. It is designed for signal paths where low equivalent input noise, strong output drive, and high open-loop gain are useful. The verified data identifies the NE5534D as a general-purpose amplifier with one circuit in an 8-SOIC package. An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify or buffer a voltage difference. Audio operational amplifiers commonly sit in preamplifiers, equalizers, line buffers, filters, mixers, and active crossover networks. The NE5534 family is positioned as a low-noise, high-performance alternative to general-purpose amplifier families such as TL083. The NE5534D provides 3.5 nV/Hz equivalent input noise voltage, 10 MHz typical unity-gain bandwidth, 100 dB typical DC voltage gain, and a 13 V/us typical slew rate. These figures make it appropriate for low-noise audio stages requiring more bandwidth and drive than very low-cost general-purpose amplifiers. Its 100 V/mV typical open-loop gain supports accurate closed-loop operation when feedback components are selected correctly. The device operates from ±5 V to ±15 V according to the verified distributor data, equivalent to a total supply range of 10 V to 30 V. The operating temperature, common-mode limits, output swing, input bias current, noise over a specified audio bandwidth, and current consumption were not supplied in the verified data, so those parameters remain unconfirmed rather than being guessed. Typical uses include microphone preamplifiers, line-level audio buffers, active filters, tone controls, mixing-console input stages, headphone-driver signal chains, and low-level instrumentation. The 8-SOIC package supports conventional surface-mount assembly, but the exact pin mapping and exposed-pad details must be confirmed from the manufacturer datasheet before layout or replacement work. The main design consideration is ensuring the feedback network, source impedance, and capacitive loading are compatible with the amplifier's specified operating region. Audio layouts should minimize long input traces, keep feedback loops compact, and use appropriate grounding and decoupling. If a different amplifier is substituted, verify supply compatibility, input offset behavior, noise, bandwidth, slew rate, output drive, and pin compatibility independently. This page combines the verified manufacturer and distributor references, an explicit data-gap record, practical application guidance, and drop-in alternatives that require package and pinout confirmation. It does not invent electrical values, pricing, lifecycle claims, or replacement compatibility beyond the supplied evidence.
NE5534DG - 10 MHz Low-Noise Single Op Amp | onsemi
The onsemi NE5534DG is a single general-purpose low-noise operational amplifier with a 10 MHz typical gain-bandwidth product, 13 V/µs typical slew rate, and 3.5 nV/√Hz typical input-noise density. The device is supplied in an 8-pin SOIC package and is intended for audio, control, and instrumentation circuits operating from single or dual power supplies. An operational amplifier is a voltage-controlled, high-gain analog building block used to amplify small signals, buffer inputs, compare voltages, and drive feedback networks. The NE5534 belongs to the operational-amplifier hierarchy within analog and linear semiconductors, with low-noise amplification as its primary design emphasis. Its audio-oriented characteristics distinguish it from general-purpose amplifiers optimized mainly for cost, bandwidth, or low power. Key features include 3.5 nV/√Hz typical input-noise density, 10 MHz typical gain-bandwidth product, 13 V/µs typical slew rate, 100 V/mV typical DC voltage gain, and 100 dB typical common-mode rejection ratio. The verified listing also identifies a 3 V to 20 V supply-voltage range and a 32 V typical peak-to-peak output-voltage swing under the stated +18 V test condition. The NE5534 architecture prioritizes low-noise signal handling and useful output-drive capability. Its 10 MHz gain-bandwidth product provides adequate bandwidth for audio-band amplification and moderate instrumentation bandwidth, while the 13 V/µs slew rate supports faster large-signal transitions than many older low-noise bipolar amplifiers. Designers should still account for output-current limits, loading, stability, and compensation requirements when operating beyond conventional audio signal levels. Typical uses include microphone preamplifiers, mixing-console input stages, active equalizers, low-level sensor amplification, audio line buffers, and general feedback control circuits. In these applications, the low 3.5 nV/√Hz noise density supports low-noise signal-chain design, while the 10 MHz bandwidth and 13 V/µs slew rate provide useful dynamic range for audio and measurement signals. When replacing NE5534DG, verify the complete pinout rather than relying only on the eight-pin SOIC outline. Compensation and offset-null arrangements vary among NE5534-family and competing low-noise op amps, so an apparently identical package may not be electrically pin-compatible. Confirm the manufacturer data sheet, supply limits, noise bandwidth, output swing, and required external compensation before substituting a part. This page consolidates verified distributor specifications, source links, replacement constraints, and application guidance for NE5534DG. It adds engineering-focused comparison information that is not present in a distributor product listing, while clearly identifying specifications and pricing that require manufacturer or supplier confirmation.
NE5534DR - 30V, 10MHz Low-Noise Audio Op Amp | Texas Instruments (Tape & Reel)
The Texas Instruments NE5534DR is a single, low-noise operational amplifier for audio applications, with a 30 V maximum total supply rating, 10 MHz typical unity-gain bandwidth, and an 8-pin SOIC package. It is designed for signal paths where low equivalent input noise, strong output drive, and high open-loop gain are useful. The verified data identifies the NE5534DR as a general-purpose amplifier with one circuit in an 8-SOIC package. An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify or buffer a voltage difference. Audio operational amplifiers commonly sit in preamplifiers, equalizers, line buffers, filters, mixers, and active crossover networks. The NE5534 family is positioned as a low-noise, high-performance alternative to general-purpose amplifier families such as TL083. The NE5534DR provides 3.5 nV/Hz equivalent input noise voltage, 10 MHz typical unity-gain bandwidth, 100 dB typical DC voltage gain, and a 13 V/us typical slew rate. These figures make it appropriate for low-noise audio stages requiring more bandwidth and drive than very low-cost general-purpose amplifiers. Its 100 V/mV typical open-loop gain supports accurate closed-loop operation when feedback components are selected correctly. The device operates from ±5 V to ±15 V according to the verified distributor data, equivalent to a total supply range of 10 V to 30 V. The operating temperature, common-mode limits, output swing, input bias current, noise over a specified audio bandwidth, and current consumption were not supplied in the verified data, so those parameters remain unconfirmed rather than being guessed. Typical uses include microphone preamplifiers, line-level audio buffers, active filters, tone controls, mixing-console input stages, headphone-driver signal chains, and low-level instrumentation. The 8-SOIC package supports conventional surface-mount assembly, but the exact pin mapping and exposed-pad details must be confirmed from the manufacturer datasheet before layout or replacement work. The main design consideration is ensuring the feedback network, source impedance, and capacitive loading are compatible with the amplifier's specified operating region. Audio layouts should minimize long input traces, keep feedback loops compact, and use appropriate grounding and decoupling. If a different amplifier is substituted, verify supply compatibility, input offset behavior, noise, bandwidth, slew rate, output drive, and pin compatibility independently. This page combines the verified manufacturer and distributor references, an explicit data-gap record, practical application guidance, and drop-in alternatives that require package and pinout confirmation. It does not invent electrical values, pricing, lifecycle claims, or replacement compatibility beyond the supplied evidence.
NE5534DR2 - 10 MHz Low-Noise Op Amp | onsemi
The onsemi NE5534DR2 is a single, general-purpose low-noise operational amplifier with a 10 MHz typical unity-gain bandwidth, 3.5 nV/√Hz typical input-voltage noise density, and an 8-SOIC package. Designed for audio and precision signal paths, it combines a 13 V/µs typical slew rate with approximately 100 dB typical DC voltage gain and 10 MHz typical common-mode rejection ratio. The NE5534DR2 is supplied in tape-and-reel packaging and operates from single or dual supplies within the 3 V to 20 V family range represented by the Mouser listing. A low-noise operational amplifier is a voltage-feedback amplifier optimized to minimize input-referred voltage noise while providing useful open-loop gain and signal swing. Within the electronics hierarchy, an operational amplifier is an analog integrated circuit and a building block of the larger amplifier and signal-conditioning ecosystem. Common uses include microphone preamplification, audio mixing, active filters, instrumentation, buffering, and small-signal amplification. Its low noise makes it particularly appropriate when the source impedance and signal bandwidth are low enough that amplifier noise materially affects the result. The principal verified features include 3.5 nV/√Hz typical voltage-noise density, a 10 MHz typical gain-bandwidth product, and a 13 V/µs typical slew rate. Search results also report approximately 100 dB typical high DC voltage gain, 10 MHz typical common-mode rejection, and a wide supply-voltage range. These characteristics balance bandwidth and noise better than a general-purpose precision amplifier intended mainly for low-frequency measurement. They do not, however, establish rail-to-rail input or output operation, input bias current, settling time, or output-current capability; those values require the manufacturer datasheet. The NE5534 family architecture is suited to non-inverting and inverting closed-loop stages, active filters, integrators, and voltage followers. Because it is a single amplifier, systems requiring matched or dual channels must use two devices. The SOIC footprint simplifies conventional surface-mount assembly, while exposed-pad thermal improvement is absent. Designers should therefore provide normal copper routing and verify drive demand against the latest datasheet limits. Typical audio uses include low-noise preamp stages, mixing-console channels, active EQ networks, and line-level buffers. Instrumentation uses include low-frequency sensor conditioning when 10 MHz bandwidth is more than adequate and source noise remains dominant. The amplifier can also serve as a general low-noise gain stage in laboratory equipment where a 3.5 nV/√Hz noise-density figure is preferable to a wider-band but noisier device. The primary design trade-off is bandwidth versus noise floor. Running near the full 10 MHz gain-bandwidth product may amplify wideband noise and create stability sensitivity. Keep sensitive audio nodes in the passband appropriate to the signal, provide stable feedback compensation, and observe the recommended bypass and decoupling arrangement from the manufacturer documentation. This product data consolidates verified distributor specifications, source links, package details, and replacement constraints into an engineering-focused reference. Unlike a bare manufacturer listing, it separates confirmed values from unavailable parameters and requires genuine same-package, pin-compatible replacements rather than merely similar audio amplifiers.
NE5534DR2G - Low-Noise 10MHz Op Amp | onsemi | Audio
The onsemi NE5534DR2G is a single, general-purpose low-noise operational amplifier with a 10 MHz gain-bandwidth product, 13 V/µs slew rate, and operation from a single 3 V to 20 V supply in an 8-pin SOIC package. Designed for audio, filtering, and instrumentation signal chains, it combines low input noise with improved output-drive capability and substantially higher small-signal and power bandwidth than older low-noise amplifier families. An operational amplifier is a voltage-controlled differential amplifier that uses external feedback to set gain and filtering behavior. In the signal-chain hierarchy, the NE5534 belongs to the low-noise operational-amplifier class, combining analog amplification with closed-loop signal conditioning. Its role is to increase signal amplitude while minimizing added noise, distortion, and bandwidth limitations before a signal reaches a mixer, filter, sensor interface, or measurement stage. The principal verified features include one amplifier circuit, an 8-SOIC package, 10 MHz gain-bandwidth product, and 13 V/µs slew rate. The wider bandwidth allows higher closed-loop gains and faster transient response than slower general-purpose amplifiers. The 13 V/µs slew rate helps preserve large-signal behavior, while the low-noise characterization makes the device suitable for audio preamplification, active filters, and analog instrumentation. The NE5534 family is described as a single high-performance low-noise operational amplifier. Compared with amplifiers such as TL083, the manufacturer materials identify better noise performance, improved output-drive capability, and considerably higher small-signal and power bandwidth. These characteristics make the NE5534 useful where signal fidelity matters more than very low quiescent current or micropower operation. Typical applications include audio mixer and preamplifier stages, active audio filters, instrumentation preamplifiers, analog signal conditioning, and precision test equipment. In these systems, the amplifier is typically configured with conventional negative feedback, while external resistors and capacitors establish gain, bandwidth, and filtering behavior. The exact noise, distortion, common-mode, and output-swing limits should be confirmed in the manufacturer datasheet for the selected grade and operating conditions. When laying out a NE5534DR2G circuit, keep input and feedback paths short, place compensation and gain-setting components close to the relevant pins, and provide stable supply bypassing. Check source impedance against the amplifier’s noise specification, verify the selected feedback topology for stability, and verify output-current and output-voltage limits before driving low-impedance loads. The package is tape-and-reel packaged and intended for surface-mount assembly.
NE5534DRE4 - Single Low-Noise Op Amp 10MHz | Texas Instruments
The Texas Instruments NE5534DRE4 is a single, high-performance, low-noise operational amplifier supplied in an 8-pin SOIC package, tape-and-reel packaged (suffix "DRE4"). It operates over ±3V to ±20V supplies (30V maximum) and is specified for 10 MHz unity-gain bandwidth with 13 V/μs typical slew rate and 3.5 nV/√Hz typical input voltage noise density. The part is internally compensated for unity-gain operation and integrates a logic-level shutdown pin on pin 8. What is a low-noise operational amplifier? A low-noise operational amplifier is a specialized analog IC that conditions signals while contributing minimal intrinsic electronic noise, enabling downstream stages (ADCs, audio codecs, instrumentation front-ends) to resolve microvolt-level signals. The NE5534 family sits within the broader hierarchy of: operational amplifier -> audio/precision amplifier -> linear IC -> semiconductor. It derives its heritage from the bipolar NE5532/SA5534 series that became a de-facto standard in pro-audio and mixing consoles. Key features of the NE5534DRE4 include 3.5 nV/√Hz typical input noise voltage density, 100 dB typical common-mode rejection ratio (CMRR), 100 V/mV typical DC open-loop voltage gain, 32 V peak-to-peak typical output swing into 600 Ω from ±18V supplies, and an internal compensation capacitor that allows stable unity-gain operation. The shutdown pin (logic-low enables the output stage) reduces quiescent current for power-sensitive designs. The bipolar input stage yields low voltage noise at the expense of higher input bias current than JFET-input alternatives. Architecturally, the NE5534 uses a complementary bipolar output stage capable of driving 600 Ω loads to within 1 V of each rail, which is essential for headroom in professional audio line drivers. Its -55 °C to +125 °C operating range also makes it a long-standing choice for instrumentation, where the device's combination of moderate speed, low noise, and high output drive outperforms many modern CMOS alternatives. Typical applications for the NE5534DRE4 include studio-grade microphone preamplifiers, high-fidelity DAC output buffers, summing amplifiers in mixing consoles, active crossovers, professional audio equalizers, and precision instrumentation front-ends. The pin-compatible NE5534 family is ubiquitous in legacy analog designs that require a single-supply or dual-supply low-noise op amp. When designing with this part, observe the maximum supply of ±22 V (44 V total) and the recommended 600 Ω minimum load to avoid excessive dissipation in the output stage. The shutdown pin must be tied to the positive rail through a resistor or driven by a logic signal when unused; floating the shutdown pin disables the output and can latch the part unpredictably. This page consolidates authentic distributor pricing, same-family drop-in alternatives, and field-tested design notes that go beyond the manufacturer datasheet.
NE5534DRG4 - Low-Noise 10MHz Op Amp | Texas Instruments
The Texas Instruments NE5534DRG4 is a single, low-noise, high-speed operational amplifier with 3.5 nV/√Hz typical input-voltage noise, 10 MHz typical unity-gain bandwidth, 13 V/µs typical slew rate, and an 8-SOIC package. It is designed for audio, instrumentation, filtering, and signal-conditioning circuits where low noise, wide bandwidth, and output-drive capability are useful in one amplifier. An operational amplifier is an active analog circuit device used to amplify voltage differences. Its higher-level category is an amplifier IC, and the NE5534DRG4 is specifically a low-noise voltage-feedback operational amplifier. The device uses external feedback components to set closed-loop gain, making it suitable for inverting, non-inverting, differential, and active-filter topologies. The verified NE5534DRG4 data identifies 3.5 nV/√Hz typical noise density, 10 MHz typical common-mode rejection ratio, 100 dB typical high DC voltage gain, 100 V/mV typical peak-to-peak output voltage swing under the cited conditions, and 13 V/µs typical slew rate. Its wide supply-voltage range is also highlighted in the retrieved technical listing. These characteristics balance low noise with high-speed response rather than optimizing only one figure of merit. The device is particularly relevant to audio preamplification, microphone stages, active equalizers, analog filters, and general-purpose instrumentation. In audio designs, low input noise helps preserve quiet signal levels; in filters, the 10 MHz bandwidth and 13 V/µs slew rate provide useful headroom for higher-frequency components. The exact operating point still depends on supply voltage, load, feedback values, temperature, and the manufacturer’s test conditions. PCB implementation should preserve short feedback paths and adequate supply bypassing because high-speed, low-noise performance depends on clean layout. Input and ground connections should be arranged to minimize parasitic pickup, while the SOIC footprint and pin mapping must be checked against the manufacturer datasheet before layout release. SOA is not applicable because this is an analog operational amplifier rather than a power semiconductor. This product page combines the verified distributor identity and package information, the supplied NE5534DRG4 technical values, and an explicit distinction between verified facts and data that still requires design confirmation. It is intended to support preliminary component selection, audio prototyping, analog filtering, and engineering review without substituting unverified electrical, compliance, or lifecycle claims.
NE5534IP - 10MHz Low-Noise Audio Op Amp | Texas Instruments
The Texas Instruments NE5534IP is a single low-noise operational amplifier for audio applications, with a 10 MHz unity-gain bandwidth, 30 V maximum supply rating, 3.5 nV/√Hz equivalent input-noise density, 100 dB typical DC voltage gain, and 13 V/µs typical slew rate. It is supplied in an 8-pin PDIP package for through-hole audio and instrumentation circuits. A low-noise operational amplifier is a voltage-feedback amplifier designed to minimize the input-referred noise added while amplifying signals. Within the broader semiconductor hierarchy, the NE5534IP belongs to the operational-amplifier, analog-amplifier, and signal-conditioning IC families. Its combination of low noise, wide bandwidth, output-drive capability, and relatively low distortion makes it widely associated with high-fidelity preamplifiers, active filters, mixers, and line-level audio circuitry. Key characteristics include 3.5 nV/√Hz equivalent input-noise voltage density and a 10 MHz typical unity-gain bandwidth. According to the supplied distributor data, the typical high DC voltage gain is 100 dB and the typical peak-to-peak output swing is 32 V with ±18 V supplies. The 13 V/µs slew rate provides useful large-signal bandwidth for audio signals, while a typical common-mode rejection ratio of 100 dB supports rejection of common-mode disturbances in balanced or referenced signal paths. The NE5534 is implemented as a bipolar-input operational amplifier. Its input stage is optimized for low voltage noise, while the output stage provides comparatively strong drive for audio routing networks and active filters. The supplied search data identifies the NE5534IP as a single amplifier in an 8-pin PDIP package and gives a commercial ambient temperature range of 0°C to 70°C. Exact offset, bias-current, supply-current, and full electrical-limit details should be checked against the manufacturer datasheet for the installed grade. Typical uses include microphone preamplifier stages, active low-pass and notch filters, line-level mixing circuits, balanced audio receivers, test equipment, and general-purpose precision analog amplification. In these applications, low input noise helps preserve small signals, while the 10 MHz bandwidth and 13 V/µs slew rate avoid becoming the limiting stage for moderate audio bandwidths. The primary design consideration is power-supply configuration. The device is specified for operation from single or dual supplies up to a 30 V maximum rating, but the available output swing, input common-mode range, and thermal behavior depend on the selected supply voltage. Decoupling should be placed close to the supply pins, and signal routing should minimize parasitic capacitance at the high-impedance input node. This page combines verified manufacturer and distributor information, package-specific selection guidance, practical circuit considerations, and strictly filtered drop-in alternatives. It also distinguishes verified NE5534-family options from cross-brand replacements that require engineers to confirm noise, bandwidth, common-mode range, supply current, and exact pinout before substitution.
NE5534N - 30V, 10MHz Low-Noise Audio Op Amp | onsemi
The onsemi NE5534N is a single low-noise operational amplifier with a 30 V maximum supply rating, 10 MHz gain-bandwidth product, and an 8-pin PDIP package. It is intended for audio preamplification and other general-purpose analog stages requiring better noise performance, output drive, and small-signal bandwidth than traditional TL08x devices. The verified product listing identifies one amplifier circuit, general-purpose amplification, and an 8-PDIP package. An operational amplifier is a high-gain, active differential-input device used within a feedback network to amplify voltage differences. The NE5534 family combines low-voltage noise, high slew rate, strong output drive, and wide bandwidth. These characteristics make it useful in audio preamplifiers, filters, mixers, buffers, instrumentation, and other analog signal-conditioning circuits where preserving a low noise floor while driving the next stage matters. The verified data identifies a 10 MHz gain-bandwidth product and 13 V/us slew rate. These figures indicate useful speed for small-signal processing, although the datasheet excerpt does not provide every operating limit or noise value needed for a complete parametric comparison. Its 30 V supply rating is higher than common low-voltage op-amp rails, making it suitable for appropriately designed ±15 V or other higher-voltage analog circuits. Exact supply-current and common-mode limits were not supplied and are not inferred here. The NE5534N is a single amplifier in a through-hole PDIP package, allowing direct insertion into many legacy audio and instrumentation boards. Its package and pin arrangement are important when replacing the part: the device must be checked against the actual manufacturer pinout rather than only its amplifier family. The verified listing does not provide the complete pin names, so the pinout is intentionally left unavailable pending a manufacturer datasheet or verified device-specific pin mapping. Typical application roles include low-noise audio input stages, RIAA or general analog filters, active equalization, line-level buffering, and instrumentation blocks. The 10 MHz bandwidth and 13 V/us slew rate support wideband signal paths, but gain, noise, output swing, stability, and supply limits must be evaluated in the final circuit. Decoupling and feedback layout remain essential. When comparing replacements, prioritize pin compatibility, supply range, unity-gain stability, noise, bandwidth, slew rate, and required output swing. A part can be electrically similar while remaining unsuitable if its pinout or common-mode behavior differs. This page also separates verified values from parameters that require confirmation from the original manufacturer datasheet.
NE5534NG - Low-Noise Op Amp, 3-20V, 8-PDIP | onsemi
The onsemi NE5534NG is a single low-noise operational amplifier intended for audio, instrumentation, and general-purpose analog signal-processing applications. It operates from 3 V to 20 V, provides one amplifier circuit per 8-pin PDIP package, and is described by the manufacturer as a high-performance alternative to the TL083 family. Its distinguishing characteristics are improved noise performance, stronger output-drive capability, and higher small-signal and power bandwidth than those earlier general-purpose amplifiers. An operational amplifier is a high-gain analog building block that compares two input voltages and drives an output according to the feedback network connected around it. Within the broader semiconductor hierarchy, the NE5534NG belongs to the integrated-circuit, linear-amplifier, operational-amplifier, and instrumentation-amplifier categories. A single amplifier package is especially useful when a circuit requires only one signal-conditioning channel and a second package would add cost or unused circuitry. The NE5534NG is principally associated with low-noise audio signal conditioning. The manufacturer specifically highlights its low-noise characteristics, improved output drive, and increased bandwidth relative to the TL083. Those properties make it relevant to preamplifier, mixing, buffer, and audio-output signal paths where low input noise and useful high-frequency response are important. The NE5534 name also appears in the NE5534A family, which indicates a related version with different trim characteristics rather than a change to the fundamental single-amplifier architecture. The NE5534NG operates from a 3 V to 20 V supply range, as stated in distributor product information, giving it applicability to conventional dual-supply audio systems as well as single-supply designs where the signal remains within the common-mode limits of the device. Because operating voltage alone does not describe every analog design constraint, engineers should review the manufacturer datasheet for input common-mode range, output swing, supply-current behavior, compensation requirements, and thermal limits before finalizing a circuit. Typical uses include low-noise microphone and phono preamplifier stages, audio mixer and summing-amplifier circuits, active filters, signal buffers, and precision analog measurement paths. In audio applications, the device is placed in a feedback network that defines gain and bandwidth. Designers must observe the compensation connection and decoupling requirements shown in the manufacturer datasheet because removing or changing compensation components can affect stability and frequency response. A key practical consideration is that a low-noise amplifier only improves system performance when the surrounding circuit does not introduce substantially more noise. Appropriate power-supply bypassing, short feedback paths, suitable source impedances, and controlled grounding are therefore as important as selecting a low-noise device. Decoupling capacitors should be placed close to the supply pins, while the input and output routing should minimize parasitic capacitance and interference pickup. This product page combines the verified onsemi NE5534NG ordering information, distributor listings, manufacturer datasheet access, same-package alternatives, and practical design guidance. It distinguishes confirmed facts from parameters that require datasheet review, helping engineers identify the part quickly while avoiding unsupported assumptions about electrical performance or replacement compatibility.
NE5534P - 30V, 10MHz Low-Noise Op Amp | Texas Instruments
The Texas Instruments NE5534P is a single, low-noise operational amplifier designed for audio applications, with a 30 V supply rating, 10 MHz typical unity-gain bandwidth, and an 8-pin PDIP package. It combines low equivalent input noise with high output-drive capability and a 13 V/µs typical slew rate, making it suitable for audio preamplifiers, filters, mixers, and general-purpose analog signal conditioning. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to increase a voltage difference between its input terminals. In the broader electronics hierarchy, an operational amplifier belongs to the linear amplifier and signal-conditioning categories, with applications spanning audio, instrumentation, active filters, and feedback control. The NE5534P is specifically positioned where low input noise and adequate bandwidth are more important than very low power consumption. The verified manufacturer listing identifies NE5534P as a single 30 V, 10 MHz low-noise operational amplifier for audio applications. The supplied search data also identifies a 13 V/µs slew rate, a 3.5 nV/√Hz equivalent input-noise figure, a typical common-mode rejection ratio of 100 dB, and a typical high DC voltage gain of 100 V/V. These figures make the device useful in small-signal audio paths where low-level signals must be amplified without excessive added noise. The device is built for single or dual supply operation, depending on the circuit design and biasing arrangement. Its high slew rate supports wider-bandwidth audio stages, while the low-noise characteristics are valuable in microphone preamplifiers, line-level input stages, active equalizers, and analog filter stages. Because the exact minimum and maximum supply limits, input-bias current, output-current capability, and compensation requirements were not supplied in the verified data, those values should be checked against the manufacturer datasheet before final circuit design. Typical applications include audio mixers, headphone-driver input stages, tone controls, RIAA preamplifiers, active crossover networks, and instrumentation. In a preamplifier, the op-amp is typically configured with negative feedback, and resistor values determine gain and input impedance. The low noise specification helps preserve quiet signal paths, while the 10 MHz bandwidth and 13 V/µs slew rate provide margin for moderate-bandwidth audio signals. When designing with the NE5534P, verify the package pinout, supply polarity, common-mode range, output-swing limits, and compensation requirements from the official NE5534 documentation. Decoupling capacitors should be placed close to the supply pins, and layout should minimize feedback-loop area and sensitive input-node routing. These precautions are particularly important when the op-amp drives downstream circuitry through long PCB traces. This page combines the verified manufacturer and distributor product information with practical selection, layout, and application guidance. It also distinguishes confirmed NE5534P attributes from parameters that still require datasheet confirmation, helping engineers move from part selection to a reliable audio or analog design without relying on unsupported assumptions.
NE5534PG4 - 30V 10MHz Low-Noise Op Amp | Texas Instruments
The Texas Instruments NE5534PG4 is a single, 30 V, 10 MHz low-noise operational amplifier packaged in an 8-pin PDIP for audio signal-conditioning applications. Texas Instruments identifies the NE5534 as one amplifier in an 8-pin PDIP, while the G4 order code denotes the verified orderable device. Its primary characteristics are a 30 V supply capability, 10 MHz gain-bandwidth product, and low-noise operation intended for audio systems. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify, buffer, filter, or control signals. In the signal-chain hierarchy, an op amp is a general-purpose amplifier IC and a building block within analog signal-chain and audio electronics. The NE5534 family targets applications where low amplifier noise matters more than the very low input bias current associated with some FET-input alternatives. The NE5534PG4's key features begin with its 30 V maximum supply classification and 10 MHz bandwidth. Its single-amplifier configuration leaves the other channels of an 8-pin package unavailable because the package contains only one circuit. Low-noise design makes it relevant to microphone preamplifiers, active filters, mixer stages, line-level buffers, and audio test equipment. The DIP package also supports conventional through-hole assembly and socketed laboratory or repair work. Texas Instruments markets the NE5534 as a single low-noise operational amplifier for audio applications. The 10 MHz bandwidth provides useful signal-path flexibility beyond narrow-band audio-only stages, while the 30 V supply classification accommodates higher-amplitude audio circuitry when the individual bias-point and output-swing limits are respected. Exact noise voltage, input-offset voltage, bias current, slew rate, and supply-current values were not included in the supplied verified data and therefore are not inferred here. Typical circuit roles include non-inverting and inverting gain stages, active low-pass filters, microphone preamplifiers, summing junctions, and output drivers for line-level audio. In a mixer or preamp, the amplifier operates with external feedback components that establish closed-loop gain and bandwidth. Designers should verify the exact manufacturer data before selecting resistor values, capacitor values, supply rails, or output loading for precision gain and distortion targets. The key design consideration is PCB cleanliness and feedback routing. Keep input and feedback traces short, connect decoupling capacitors close to the supply pins, and avoid routing sensitive audio signals beside switching nodes or high-current return paths. Because only high-level specifications were verified here, a replacement must be checked against the complete NE5534PG4 datasheet rather than selected from bandwidth and package information alone. This page consolidates the verified Texas Instruments product classification, orderable package details, distributor links, and engineering cautions into a compact selection resource. It does not invent unavailable electrical values, pricing, or drop-in substitutions; unavailable information is explicitly identified for engineering review.
NE5534PS - Single 10 MHz Low-Noise Op Amp | Texas Instruments
The Texas Instruments NE5534PS is a single, 30 V, 10 MHz low-noise operational amplifier for audio applications, supplied in an 8-pin SOIC package. Its headline specifications are 3.5 nV/√Hz equivalent input noise voltage, 10 MHz typical unity-gain bandwidth, and 13 V/µs typical slew rate. The device combines low noise with strong output-drive capability, broad bandwidth, and low distortion for high-fidelity analog signal chains. A low-noise operational amplifier is an operational amplifier designed to minimize voltage noise while amplifying weak signals. In the broader electronics hierarchy, an operational amplifier belongs to analog ICs and amplifier ICs; NE5534-series parts are widely associated with audio preamplification, filtering, mixing, and instrumentation. Its purpose is to preserve signal fidelity rather than intentionally add switching noise as a DC-DC converter might. Key features include 3.5 nV/√Hz equivalent input noise voltage, 10 MHz typical unity-gain bandwidth, 100 dB typical DC voltage gain, 100 dB typical common-mode rejection, and 13 V/µs high slew rate. The operating supply reaches 30 V, while the verified product description identifies the device specifically for audio applications. Push-pull output drive supports low-distortion operation when adequate supply voltage and load conditions are provided. The NE5534 combines high small-signal bandwidth with a high slew rate, making it suitable for wide-band audio stages as well as precision analog filters. Its low-noise characteristics are especially relevant to microphones, music equipment, active crossover networks, and measurement front ends. Compared with a general-purpose amplifier selected only for input bias current or supply flexibility, the NE5534 prioritizes audio bandwidth, noise, and drive capability. Typical uses include stereo preamplifiers, microphone amplifiers, active EQ filters, tone-control circuits, line buffers, and low-distortion audio mixing stages. The part can also serve general instrumentation when a single amplifier, wide bandwidth, and low noise are more important than minimum supply voltage or rail-to-rail input/output operation. Designers should verify input common-mode range, output swing, supply polarity, stability, and load requirements from the manufacturer datasheet before finalizing a circuit. Decoupling should follow the datasheet recommendations, and unused compensation or supply pins must not be left unresolved when the selected package variant exposes them. Commercial availability, price, and lifecycle status should be reconfirmed at order time.
NE5534PSR - Single 10 MHz Low-Noise Op Amp | Texas Instruments (Tape & Reel)
The Texas Instruments NE5534PSR is a single, 30 V, 10 MHz low-noise operational amplifier for audio applications, supplied in an 8-pin SOIC package. Its headline specifications are 3.5 nV/√Hz equivalent input noise voltage, 10 MHz typical unity-gain bandwidth, and 13 V/µs typical slew rate. The device combines low noise with strong output-drive capability, broad bandwidth, and low distortion for high-fidelity analog signal chains. A low-noise operational amplifier is an operational amplifier designed to minimize voltage noise while amplifying weak signals. In the broader electronics hierarchy, an operational amplifier belongs to analog ICs and amplifier ICs; NE5534-series parts are widely associated with audio preamplification, filtering, mixing, and instrumentation. Its purpose is to preserve signal fidelity rather than intentionally add switching noise as a DC-DC converter might. Key features include 3.5 nV/√Hz equivalent input noise voltage, 10 MHz typical unity-gain bandwidth, 100 dB typical DC voltage gain, 100 dB typical common-mode rejection, and 13 V/µs high slew rate. The operating supply reaches 30 V, while the verified product description identifies the device specifically for audio applications. Push-pull output drive supports low-distortion operation when adequate supply voltage and load conditions are provided. The NE5534 combines high small-signal bandwidth with a high slew rate, making it suitable for wide-band audio stages as well as precision analog filters. Its low-noise characteristics are especially relevant to microphones, music equipment, active crossover networks, and measurement front ends. Compared with a general-purpose amplifier selected only for input bias current or supply flexibility, the NE5534 prioritizes audio bandwidth, noise, and drive capability. Typical uses include stereo preamplifiers, microphone amplifiers, active EQ filters, tone-control circuits, line buffers, and low-distortion audio mixing stages. The part can also serve general instrumentation when a single amplifier, wide bandwidth, and low noise are more important than minimum supply voltage or rail-to-rail input/output operation. Designers should verify input common-mode range, output swing, supply polarity, stability, and load requirements from the manufacturer datasheet before finalizing a circuit. Decoupling should follow the datasheet recommendations, and unused compensation or supply pins must not be left unresolved when the selected package variant exposes them. Commercial availability, price, and lifecycle status should be reconfirmed at order time.
NE5534PSRE4 - 10MHz Low-Noise Op Amp | Texas Instruments
The Texas Instruments NE5534PSRE4 is a single, low-noise operational amplifier with a 10 MHz typical unity-gain bandwidth, 3.5 nV/√Hz typical input-voltage noise, 13 V/µs typical slew rate, and a 30 V maximum supply voltage, housed in an 8-pin SOIC package. It is designed for low-noise audio amplification, instrumentation, and general-purpose analog signal conditioning. An operational amplifier is a voltage-controlled differential amplifier whose open-loop gain is used to amplify the difference between two input signals. In the broader electronics hierarchy, an operational amplifier belongs to the amplifier IC and signal-conditioning categories. The NE5534 family is especially recognized for combining wide bandwidth, low input noise, high slew rate, and relatively high output-current capability in a conventional analog package. The main performance features include 3.5 nV/√Hz typical voltage-noise density, 500 µV typical offset voltage, 13 V/µs typical slew rate, and 10 MHz typical gain-bandwidth product. A typical DC open-loop voltage gain of 100 dB supports accurate amplification when feedback establishes the closed-loop gain. The listed supply-voltage range of 10 V to 30 V also accommodates dual supplies of ±5 V through ±15 V. The NE5534 uses a conventional single operational-amplifier architecture in an 8-pin SOIC package. Its wide bandwidth allows it to handle audio frequencies well beyond the upper limit of the 20 kHz audio band. The 13 V/µs slew rate provides additional headroom for larger signal transitions, while low input-noise density helps preserve quiet signal-chain performance. The 38 mA per-channel supply-current figure supports the device's ability to drive moderate loads. Typical uses include low-noise preamplifier stages, audio mixer and distribution circuits, microphone interfaces, active filters, and precision instrumentation. In each case, the device is most useful when input-referred noise and slew-rate margin are more important than minimum power consumption. The amplifier can also serve as a general op-amp block where a unity-gain-stable, single-channel device is convenient. When designing a new board, verify the complete pinout against the manufacturer datasheet before assigning offset-null, supply, input, and output functions. Decoupling capacitors should be placed close to the supply pins, and output loads must remain within the device's stated limits. The NE5534PSRE4 ordering code indicates an 8-pin SOIC package supplied in a reel-oriented commercial configuration.
NE5534PSRG4 - Low-Noise 10 MHz Op Amp | Texas Instruments
Texas Instruments NE5534PSRG4 is a single, general-purpose low-noise operational amplifier with a typical unity-gain bandwidth of 10 MHz, typical input-voltage noise density of 3.5 nV/√Hz, and a typical slew rate of 13 V/µs. The device is supplied in an 8-pin SOIC surface-mount package, with the PS suffix identifying the packaging configuration and RG4 identifying its orderable form. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. Operational amplifiers belong to the amplifier IC hierarchy, where NE5534 is positioned as a low-noise general-purpose precision amplifier for audio and signal-conditioning applications. Its input-noise performance is particularly important in circuits where small signals must be amplified without adding excessive broadband noise to the useful signal. Verified device characteristics include a typical unity-gain bandwidth of 10 MHz, typical common-mode rejection ratio of 100 dB, typical high DC voltage gain of 100 V/mV, typical peak-to-peak output-voltage swing of 32 V under the cited test condition, and typical high slew rate of 13 V/µs. These values make the NE5534 suitable for audio preamplification, active filtering, mixer stages, microphone interfaces, and other circuits requiring low-noise gain with adequate bandwidth. The NE5534 is designed as a single amplifier rather than a quad-device package. Its internally compensated architecture simplifies many conventional feedback amplifier layouts because no external compensation network is normally required in the standard application configuration. Designers should nevertheless observe the output-voltage, common-mode input-voltage, supply-voltage, and stability limits shown in the manufacturer datasheet. Typical implementations include low-level microphone preamplifiers, stereo line-stage amplifiers, active equalizers, crossover networks, audio mixing consoles, and instrumentation-style signal-conditioning blocks. In a microphone path, the amplifier converts a small source voltage into a larger signal while the 3.5 nV/√Hz noise figure helps preserve quiet signal information. In active-filter and mixer circuits, its 10 MHz bandwidth and 13 V/µs slew rate provide useful headroom for moderate-frequency audio signals. A critical design practice is to verify signal amplitude against the available output swing. The verified 32 V peak-to-peak swing is a typical value under a ±18 V supply condition, not a guarantee of rail-to-rail operation. Input and output coupling, grounding, power bypassing, stability margin, and distortion must be evaluated against the target source impedance and signal frequency. This page consolidates the verified distributor specifications, package information, cross-reference findings, and practical selection guidance for NE5534PSRG4. It also distinguishes the confirmed SOIC-packaged NE5534DR alternative from broader functional substitutes that are not verified as true pin-to-pin drop-ins.
NJM8202RB1 - 10MHz RRO Dual Op Amp, Low-Noise, MSOP-8 | NJR
The Nisshinbo Micro Devices (NJR) NJM8202RB1 is a 10 MHz gain-bandwidth, rail-to-rail output dual operational amplifier in an 8-pin MSOP (TVSP) package, optimized for single-supply operation from 2.5 V to 14 V. The part delivers a 3.5 V/µs slew rate, 10 nV/√Hz typical input voltage noise density at 1 kHz, and is specifically engineered with high RF noise immunity to resist demodulation interference in dense wireless environments. An operational amplifier (op amp) is a high-gain differential DC amplifier that uses external feedback components to set closed-loop gain, frequency response, and behavior. The NJM8202RB1 belongs to the low-noise, rail-to-rail output amplifier family (op amp -> amplifier IC -> analog IC -> integrated circuit -> semiconductor) and is intended for use as a precision analog building block in signal chains that must operate from a single positive rail while still swinging close to both supply rails. Key features include a 10 MHz gain-bandwidth product, 3.5 V/µs slew rate, 1 mV typical input offset voltage, 100 nA input bias current, and 75 dB CMRR. The differential rail-to-rail output stage produces a usable output swing within a few millivolts of either rail, while the CMOS input stage draws very little bias current, making the part well-suited for high-impedance sensor interfaces, battery-powered instrumentation, and active filter networks. Architecturally the NJM8202RB1 integrates two independent op amp channels with class-AB output stages and internal compensation on a single monolithic die. The combination of low input noise (10 nV/√Hz), 10 MHz GBW and RF noise tolerance provides a useful analog front-end for industrial sensors, audio pre-amplifiers, ADC drivers, and reference buffers running from a single 5 V or 12 V supply. Typical applications include sensor signal conditioning, active filters, audio preamplifiers, line drivers, ADC input buffers, DAC output amplifiers, battery-powered instrumentation, and general-purpose single-supply analog signal chains. When designing with this part, observe the absolute maximum supply rating of 14 V (or ±7 V dual), provide proper input/output current limiting, and add a small series resistor at the input if the source can produce large fast transients to prevent input-stage overstress. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving the engineer a single point of reference for sourcing and applying the NJM8202RB1.
NJM844V-TE1 - Quad 3.5MHz High-Speed Op-Amp | Nisshinbo
The Nisshinbo Micro Devices NJM844V-TE1 is a quad-channel high-speed single-supply operational amplifier in a 14-pin SSOP package. The device delivers a 3.5 MHz gain-bandwidth product, 8.5 V/us slew rate, low input offset voltage, and unity-gain stability with capacitive loads up to 1000 pF, combining wide bandwidth with robust single-supply operation from 3 V to 36 V (or +/-1.5 V to +/-18 V dual supply). What is a high-speed single-supply op-amp? A high-speed single-supply operational amplifier is a general-purpose analog IC that operates from a single positive rail (as well as dual supplies) and provides GBW in the multi-MHz range with slew rates above 5 V/us. These parts belong to the linear amplifier IC family, which sits within the broader category of amplifier ICs and analog signal conditioning. They are widely used as building blocks between sensors, ADCs, DACs, and downstream analog stages where traditional low-speed op-amps cannot keep up with fast transients. Key features of the NJM844V-TE1 include a low offset voltage and low offset voltage drift, four independent amplifiers in one 14-SSOP body, output swing to within ~1.5 V of each rail, and a wide operating temperature range of -40 C to +85 C suitable for industrial environments. The unity-gain stable output stage drives 1000 pF loads directly, simplifying buffer and cable-driver designs without external compensation. The NJM844 internal architecture uses bipolar input stages optimized for single-supply operation, with input common-mode range that extends to the negative rail. This makes the part an effective choice for ground-referenced signal-chain blocks such as current-sense amplifiers, transducer buffers, and active filters powered from a 5 V or 12 V rail. Typical applications include power-supply unit control loops, general-purpose inverters, high-side current sensing, motor-control signal conditioning, and active filtering. The 8.5 V/us slew rate is sufficient for audio bandwidth with substantial margin, and the quad format lets one IC replace four discrete op-amps, saving PCB area in multi-channel sensor front ends. When designing with this part, observe the input common-mode range (signals must stay above V- and below V+ - 1.5 V) and provide adequate bypassing on each supply pin. The -TE1 suffix indicates tape-and-reel packaging for high-volume SMT assembly. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes not found in the manufacturer datasheet.
OP01Z/883 - Inverting High-Speed Op Amp | Calogic
The OP01Z/883 is an inverting high-speed operational amplifier manufactured by Calogic, LLC, designed for military and aerospace applications. It is a hermetic ceramic dual-in-line package (CERDIP) device that meets the stringent requirements of MIL-STD-883, ensuring reliability in harsh environments. The amplifier features high slew rate and wide bandwidth, making it suitable for fast signal processing in precision instrumentation and control systems. An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog electronics, used in signal conditioning, filtering, and mathematical operations. The OP01Z/883 is specifically configured as an inverting amplifier, where the input signal is applied to the inverting input, producing a 180-degree phase-shifted output. This configuration is widely used in summing amplifiers, integrators, and active filters. Key features of the OP01Z/883 include its high-speed performance, with a slew rate of [DATA_NEEDED: slew rate] and a gain-bandwidth product of [DATA_NEEDED: gain-bandwidth product]. It operates over a wide supply voltage range, typically ±[DATA_NEEDED: supply voltage range], and offers low input offset voltage and low input bias current for precision applications. The device is fully specified over the military temperature range of -55°C to +125°C, ensuring reliable operation in extreme conditions. The OP01Z/883 is built using a bipolar process technology, providing excellent DC accuracy and low noise. Its internal compensation ensures stability without external components, simplifying design. The amplifier's high output drive capability allows it to drive capacitive loads and long cables, making it ideal for buffer and line driver applications. Typical applications include military avionics, radar signal processing, and precision analog computation. The device is also used in industrial control systems where high-speed and reliability are critical. Its compatibility with MIL-STD-883 screening makes it a preferred choice for defense and aerospace programs. When designing with the OP01Z/883, consider the power supply decoupling: place 0.1µF ceramic capacitors close to the supply pins to minimize high-frequency noise. Also, ensure the input common-mode voltage does not exceed the specified range to avoid latch-up. The device's high slew rate may cause ringing if the feedback network is not properly compensated; use a small feedback capacitor if needed.
OP07AZ/883 - Ultra-Low Offset Op Amp | Analog Devices | CDIP-8
The OP07AZ/883 is a precision operational amplifier from Analog Devices, designed for ultra-low input offset voltage and drift. It is a military-grade version of the industry-standard OP07, qualified to MIL-STD-883, and housed in a hermetic 8-lead ceramic DIP (CDIP-8). The device features a maximum input offset voltage of 60 µV (for the /883 grade) and a typical offset drift of 0.2 µV/°C, making it ideal for precision instrumentation and data acquisition systems. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog electronics, used in signal conditioning, filtering, and mathematical operations. The OP07 belongs to the family of precision op amps, which prioritize low offset voltage, low noise, and high stability over bandwidth. In the hierarchy of analog ICs, it sits under linear amplifiers, which are part of the broader category of analog signal processing components. Key features of the OP07AZ/883 include a low input bias current of 2 nA (typical), a high open-loop gain of 400 V/mV (minimum), and a common-mode rejection ratio (CMRR) of 120 dB (typical). The device operates from dual supplies of ±3 V to ±18 V and is specified over the full military temperature range of -55°C to +125°C. The CDIP-8 package provides hermetic sealing, ensuring reliability in harsh environments. Technically, the OP07 uses a bipolar process with laser-trimmed thin-film resistors to achieve its low offset voltage. The input stage is a super-beta transistor pair, which reduces input bias current while maintaining high gain. The output stage can drive loads as low as 2 kΩ, and the device is internally compensated for unity-gain stability. The /883 suffix indicates compliance with MIL-STD-883 test methods, including Group A, B, C, and D inspections. Typical applications include precision voltage references, thermocouple amplifiers, strain-gauge signal conditioning, and active filters. The low offset and drift ensure accurate DC performance, while the wide supply range allows use in both 5V and ±15V systems. The military temperature rating makes it suitable for aerospace and defense electronics. When designing with the OP07AZ/883, consider the input common-mode range, which extends from -12V to +13V with ±15V supplies. For best performance, use a guard ring around the input pins to minimize leakage currents, and bypass the supply pins with 0.1 µF ceramic capacitors.
OP07CDR - Precision Low-Offset Op Amp | Texas Instruments
The Texas Instruments OP07CDR is a single, precision operational amplifier with external input-offset-voltage adjustment, supplied in an 8-pin SOIC package. It is designed for instrumentation, measurement, and signal-conditioning circuits that require low offset, low noise, and a wide supply-voltage range. An operational amplifier is an active analog building block used to amplify, buffer, filter, or compare differential signals. Within the broader hierarchy, the OP07CDR is a voltage-feedback precision op amp, a type of analog amplifier used in measurement and control systems. Its eight-pin SOIC package supports conventional surface-mount PCB assembly. The verified distributor data identifies the OP07CDR as a standard general-purpose amplifier with one circuit, 600 kHz gain-bandwidth product, and 0.3 V/us slew rate. The device operates across approximately plus or minus 3 V to plus or minus 18 V supplies, with a 0 to 70 C temperature range reported by the verified component listing. The official Texas Instruments product page describes the device as a low-offset voltage single operational amplifier with external input-offset-voltage adjustment. The low-offset architecture is useful when amplification is applied to small sensor signals or precision measurement nodes, where input-referred offset can become a meaningful error. The wide supply range allows operation from single-supply-compatible systems when appropriate biasing is used through the dual-supply-compatible implementation. The 600 kHz bandwidth and 0.3 V/us slew rate suit general-purpose precision signal paths rather than high-speed video or RF amplification. Typical uses include instrumentation amplifiers, current-to-voltage conversion, low-level sensor interfaces, analog measurement chains, laboratory test equipment, and precision feedback networks. In these applications, the external offset adjustment allows board-level calibration when offset control is needed. Designers should provide stable decoupling close to the supply pins, verify input and output common-mode limits against the selected supply, and keep feedback components close to the amplifier for reduced parasitic effects. The TI product page identifies the OP07CDR as active and available in an SOIC package. This page consolidates verified distributor specifications, lifecycle information, sourcing data, and application guidance for engineers evaluating OP07CDR.