بەرهەمەکان (970+)

MK2059-01SILF 25.92MHz Clock Translator | Renesas
MK2059-01SILF

MK2059-01SILF 25.92MHz Clock Translator | Renesas

Renesas Electronics MK2059-01SILF is a VCXO-based frame-clock frequency translator IC that generates a 25.92 MHz output clock from an 8 kHz frame-rate reference. The device is packaged in a 20-pin SOIC measuring 0.295 inch, or 7.50 mm, in width. Its principal function is to translate a low-frequency frame reference into a stable telecommunications clock while maintaining phase locking to the reference input. A VCXO-based clock frequency translator belongs to the clock and timing IC hierarchy, where it sits between a low-frequency synchronization reference and the higher-frequency clocks used by communications equipment. Unlike a simple frequency divider, this architecture uses a voltage-controlled crystal oscillator to generate the output clock and phase-lock it to the incoming 8 kHz frame signal. This makes the device relevant where equipment must derive a common reference frequency from an existing frame network. The MK2059-01SILF is identified as a clock synthesizer and jitter-cleaning device with a 25.92 MHz output. Its 20-pin SOIC package provides a surface-mount implementation for telecommunications and other synchronous electronic systems. The 25.92 MHz result supports clocking roles requiring a substantially higher frequency than the 8 kHz synchronization reference, while the phase-locked architecture provides a defined relationship to the original frame timing. Technically, the key operating concept is the interaction between the VCXO and the phase-locking loop. The frame reference establishes the target phase relationship, and the controlled oscillator produces the corresponding high-frequency output. Compared with distributing a free-running oscillator alone, this arrangement is intended for equipment that must remain aligned with a wider network timing reference. Detailed loop bandwidth, jitter, supply-voltage limits, and current limits must be confirmed in the manufacturer datasheet before release to production. Typical applications include telecommunications line-card clocking, frame synchronization, network-interface timing, and embedded communications equipment. It can also be considered wherever an 8 kHz frame reference must be converted into a 25.92 MHz clock without redesigning the surrounding timing architecture. Designers should validate the reference frequency, output frequency, load requirements, and loop behavior against the complete system timing budget. The primary design consideration is to treat the reference and output clocks as a controlled phase-locked system. Use the manufacturer pin-description table when assigning PCB tracks, and preserve the recommended grounding and decoupling arrangement around the clock and power pins. Because clock translators can amplify supply noise or layout disturbance into timing errors, short return paths and controlled impedance are especially important. This page organizes the device function, package information, sourcing questions, drop-in comparison limits, and design cautions into a compact engineering reference. It also separates confirmed product facts from parameters that still require verification against the Renesas datasheet, helping designers avoid treating an incomplete clock specification as a production-ready guarantee.

RFQ پەیوەندی
MK2059-01SITR - 25.92MHz Clock Translator | Renesas | Telecom (Tape & Reel)
MK2059-01SITR

MK2059-01SITR - 25.92MHz Clock Translator | Renesas | Telecom (Tape & Reel)

The Renesas Electronics MK2059-01SITR is a VCXO-based frame clock frequency translator with a maximum output frequency of 25.92 MHz, LVCMOS input and output interfaces, and a 20-pin SOIC package. It accepts an 8 kHz frame-rate reference clock and phase-locks its generated output to that reference, producing common telecommunications clock frequencies. A voltage-controlled crystal oscillator-based clock translator is a clock-generation IC that combines frequency translation, phase locking, and reference synchronization. It belongs to the broader clock and timing IC hierarchy, where clock generators and phase-locked loops support communication networks, digital transport systems, and other equipment requiring stable, traceable timing references. Unlike a free-running oscillator, the MK2059-01SITR derives its output from an external reference, improving synchronization across a telecommunications system. Key features include a 25.92 MHz maximum output frequency, an input-to-output ratio of 2:1, LVCMOS input and output signaling, and an integrated PLL. The supply-voltage range is 3.15 V to 3.45 V, while the rated operating-temperature range is -40°C to +85°C. The surface-mount 20-SOIC package provides a compact option for communication and timing equipment. Internally, the device uses a VCXO-based architecture and PLL-based clock generation to lock the generated clock to the 8 kHz input reference. This phase-locked relationship is the principal technical feature: the output is not intended as an unrelated free-running oscillator but as a translated reference derived from the incoming frame clock. The PLL feature and LVCMOS interfaces place the device in the class of integrated frequency translators intended for telecommunications clocking. Typical applications include telecommunications line equipment, frame-clock synchronization networks, clock distribution subsystems, and communication interfaces that require a derived reference from an 8 kHz source. The 25.92 MHz maximum output makes it suitable for systems operating at the stated common telecommunications reference frequency, while the 3.15 V to 3.45 V supply range supports low-voltage digital clock architectures. Designers should verify the input reference amplitude, output waveform, PLL loop stability, and decoupling requirements against the manufacturer datasheet before layout. The LVCMOS clock path requires short, controlled-impedance routing and clean return paths, while the 20-SOIC footprint requires adequate board area and thermal consideration for reliable assembly. This page combines verified manufacturer and distributor information with explicit data gaps, application guidance, and package-specific replacement analysis. It is intended to help engineers evaluate the MK2059-01SITR without mistaking packaging variants for functionally different devices or assuming unreported electrical specifications.

RFQ پەیوەندی
MK2069-01GI - 160MHz VCXO Clock Synchronizer | Renesas
MK2069-01GI

MK2069-01GI - 160MHz VCXO Clock Synchronizer | Renesas

The Renesas Electronics MK2069-01GI is a VCXO-based line-card clock synchronizer with a maximum stated frequency of 160 MHz, a 3.15 V to 3.45 V supply range, and a 56-pin thin TSSOP package measuring 0.240 inch, or 6.10 mm, in width. It combines system synchronization, jitter attenuation, and frequency multiplication or translation in one mixed analog and digital timing IC. A clock synchronizer is a timing integrated circuit that coordinates one or more clock domains by selecting reference inputs and distributing or conditioning clock signals. The MK2069-01GI belongs to the broader clock generator, PLL, and frequency synthesizer category, where its VCXO architecture provides a variable-frequency reference that can be controlled to support synchronization and output-frequency conversion. The principal verified features include a 160 MHz maximum clock frequency, three alternate reference inputs, an asynchronous input multiplexer, and LVCMOS differential outputs. ICLK0 and ICLK1 are 5 V tolerant according to the manufacturer datasheet, while the remaining reference inputs do not share that stated tolerance. The device is intended for surface mounting in a 56-TFSOP package and operates over the disclosed -40 °C to 85 °C range. The MK2069-01 uses a VCXO-based architecture to deliver the performance expected of a canned VCXO-based hybrid timing device at a lower cost. Its mixed analog and digital implementation makes PCB layout and external component selection especially important. Short, controlled routing, suitable grounding, and compliant external crystal-network components are necessary to preserve timing performance and stability. Typical uses include line-card clock synchronization, telecommunications equipment, communication infrastructure, frequency translation, and jitter-sensitive clock distribution. A 160 MHz ceiling makes the device relevant to systems that distribute a common reference while requiring selectable reference sources or attenuated clock paths. Designers should treat the 3.15 V to 3.45 V supply range as a hard constraint and should not infer 5 V operation merely because ICLK0 and ICLK1 are 5 V tolerant. The input multiplexer selection is asynchronous and non-latched, so control timing and switching behavior should be evaluated against the system requirements. Exact power consumption, jitter limits, output configurations, and full pin assignments require confirmation from the manufacturer datasheet before layout release. This product record combines verified manufacturer and distributor information with package-specific engineering guidance, sourcing context, and candid identification of parameters that still require design-in verification.

RFQ پەیوەندی
MK2069-01GITR - 160MHz VCXO Clock Synchronizer | Renesas (Tape & Reel)
MK2069-01GITR

MK2069-01GITR - 160MHz VCXO Clock Synchronizer | Renesas (Tape & Reel)

The Renesas Electronics MK2069-01GITR is a VCXO-based line-card clock synchronizer with a maximum stated frequency of 160 MHz, a 3.15 V to 3.45 V supply range, and a 56-pin thin TSSOP package measuring 0.240 inch, or 6.10 mm, in width. It combines system synchronization, jitter attenuation, and frequency multiplication or translation in one mixed analog and digital timing IC. A clock synchronizer is a timing integrated circuit that coordinates one or more clock domains by selecting reference inputs and distributing or conditioning clock signals. The MK2069-01GITR belongs to the broader clock generator, PLL, and frequency synthesizer category, where its VCXO architecture provides a variable-frequency reference that can be controlled to support synchronization and output-frequency conversion. The principal verified features include a 160 MHz maximum clock frequency, three alternate reference inputs, an asynchronous input multiplexer, and LVCMOS differential outputs. ICLK0 and ICLK1 are 5 V tolerant according to the manufacturer datasheet, while the remaining reference inputs do not share that stated tolerance. The device is intended for surface mounting in a 56-TFSOP package and operates over the disclosed -40 °C to 85 °C range. The MK2069-01 uses a VCXO-based architecture to deliver the performance expected of a canned VCXO-based hybrid timing device at a lower cost. Its mixed analog and digital implementation makes PCB layout and external component selection especially important. Short, controlled routing, suitable grounding, and compliant external crystal-network components are necessary to preserve timing performance and stability. Typical uses include line-card clock synchronization, telecommunications equipment, communication infrastructure, frequency translation, and jitter-sensitive clock distribution. A 160 MHz ceiling makes the device relevant to systems that distribute a common reference while requiring selectable reference sources or attenuated clock paths. Designers should treat the 3.15 V to 3.45 V supply range as a hard constraint and should not infer 5 V operation merely because ICLK0 and ICLK1 are 5 V tolerant. The input multiplexer selection is asynchronous and non-latched, so control timing and switching behavior should be evaluated against the system requirements. Exact power consumption, jitter limits, output configurations, and full pin assignments require confirmation from the manufacturer datasheet before layout release. This product record combines verified manufacturer and distributor information with package-specific engineering guidance, sourcing context, and candid identification of parameters that still require design-in verification.

RFQ پەیوەندی
MK2069-04GI - 160MHz VCXO Clock Translator | Renesas
MK2069-04GI

MK2069-04GI - 160MHz VCXO Clock Translator | Renesas

The Renesas Electronics MK2069-04GI is a VCXO-based universal clock translator with a maximum operating frequency of 160 MHz, PLL-based clock generation, and LVCMOS input/output interfaces. It is packaged in a 56-TFSOP package measuring approximately 6.10 mm in width. The device is intended for translating clock frequencies between systems whose clocks do not share a convenient direct integer relationship. A VCXO-based clock translator is a clock-generation and timing-management device that uses a voltage-controlled crystal oscillator and phase-locked loop architecture. In the broader semiconductor hierarchy, it belongs to the clock and timing IC category, where PLL-based translators condition, multiply, divide, or otherwise redistribute reference-clock energy. The MK2069-04GI provides a single LVCMOS clock output path and uses selectable reference and feedback dividers to establish the translation ratio. Key features include support for frequencies up to 160 MHz, PLL operation, LVCMOS signal compatibility, and user-selectable divider ranges. The on-chip VCXO produces a stable, low-jitter output clock using a phase detector frequency down to 8 kHz or lower. This architecture is useful for telecom frame clocks, including standards operating from an 8 kHz common clock, and for other systems requiring clock conversion between unrelated frequencies. The PLL phase detector, reference divider, feedback divider, and VCXO work together to correct phase and frequency errors between the incoming reference and the generated output. Divider selection determines the effective multiplication ratio, while the output stage delivers the resulting clock in LVCMOS form. The device also provides jitter attenuation of the input clock and can accept low input frequencies, making it useful where conventional integer-ratio clock trees are insufficient. Typical applications include telecom line-card clock translation, network interface clocking, communications equipment, test and measurement systems, and embedded systems that need a locally generated clock with low jitter. The part can also support clock-domain adaptation where the source and destination frequencies have a low common denominator. In each case, the design must select divider values compatible with the PLL operating range and preserve the required output-to-input phase relationship. Designers should verify the reference and feedback divider combinations, input slew rate, output loading, and loop stability against the manufacturer datasheet. The 56-TFSOP footprint requires adequate board area and careful routing of clock inputs and power supplies. Decoupling close to the supply pins and a controlled source impedance are important for maintaining predictable phase noise and jitter performance. This product summary consolidates distributor availability information, manufacturer-based clock architecture details, replacement guidance, and practical implementation considerations into a design-oriented reference for engineers evaluating the MK2069-04GI.

RFQ پەیوەندی
MK2069-04GITR - 160MHz VCXO Clock Translator | Renesas (Tape & Reel)
MK2069-04GITR

MK2069-04GITR - 160MHz VCXO Clock Translator | Renesas (Tape & Reel)

The Renesas Electronics MK2069-04GITR is a VCXO-based universal clock translator with a maximum operating frequency of 160 MHz, PLL-based clock generation, and LVCMOS input/output interfaces. It is packaged in a 56-TFSOP package measuring approximately 6.10 mm in width. The device is intended for translating clock frequencies between systems whose clocks do not share a convenient direct integer relationship. A VCXO-based clock translator is a clock-generation and timing-management device that uses a voltage-controlled crystal oscillator and phase-locked loop architecture. In the broader semiconductor hierarchy, it belongs to the clock and timing IC category, where PLL-based translators condition, multiply, divide, or otherwise redistribute reference-clock energy. The MK2069-04GITR provides a single LVCMOS clock output path and uses selectable reference and feedback dividers to establish the translation ratio. Key features include support for frequencies up to 160 MHz, PLL operation, LVCMOS signal compatibility, and user-selectable divider ranges. The on-chip VCXO produces a stable, low-jitter output clock using a phase detector frequency down to 8 kHz or lower. This architecture is useful for telecom frame clocks, including standards operating from an 8 kHz common clock, and for other systems requiring clock conversion between unrelated frequencies. The PLL phase detector, reference divider, feedback divider, and VCXO work together to correct phase and frequency errors between the incoming reference and the generated output. Divider selection determines the effective multiplication ratio, while the output stage delivers the resulting clock in LVCMOS form. The device also provides jitter attenuation of the input clock and can accept low input frequencies, making it useful where conventional integer-ratio clock trees are insufficient. Typical applications include telecom line-card clock translation, network interface clocking, communications equipment, test and measurement systems, and embedded systems that need a locally generated clock with low jitter. The part can also support clock-domain adaptation where the source and destination frequencies have a low common denominator. In each case, the design must select divider values compatible with the PLL operating range and preserve the required output-to-input phase relationship. Designers should verify the reference and feedback divider combinations, input slew rate, output loading, and loop stability against the manufacturer datasheet. The 56-TFSOP footprint requires adequate board area and careful routing of clock inputs and power supplies. Decoupling close to the supply pins and a controlled source impedance are important for maintaining predictable phase noise and jitter performance. This product summary consolidates distributor availability information, manufacturer-based clock architecture details, replacement guidance, and practical implementation considerations into a design-oriented reference for engineers evaluating the MK2069-04GITR.

RFQ پەیوەندی
MK2302S-01 - 168MHz Zero-Delay Clock Buffer | Renesas
MK2302S-01

MK2302S-01 - 168MHz Zero-Delay Clock Buffer | Renesas

The Renesas Electronics MK2302S-01 is a 168 MHz zero-delay buffer (ZDB) with an integrated analog/digital phase-locked loop, supplied in an 8-pin SOIC package. It provides one clock circuit, a CMOS clock output, and operates from a verified 3.15 V to 3.45 V supply range. The device is designed to regenerate and distribute clock signals where predictable frequency, controlled phase relationship, and multiple output drive capability are required. A zero-delay buffer is a clock-management device intended to reproduce an input clock at one or more outputs while controlling propagation delay and phase relationship. The MK2302S-01 uses PLL techniques to distribute a clock signal and can therefore be useful in systems where the source clock must be isolated or regenerated before reaching multiple sequential or communications circuits. In the system hierarchy, it belongs to the clock and timing IC family rather than a general-purpose logic IC. Verified device characteristics include a maximum frequency of 168 MHz, one clock circuit, a CMOS output, and a 3.15 V to 3.45 V supply range. The manufacturer and distributor search results identify the part as a multiplier and zero-delay buffer. Additional timing, output-current, jitter, temperature, and package-dimension values were not supplied in the verified data and therefore require confirmation from the manufacturer datasheet before final design release. Typical uses include clock distribution for communications equipment, digital logic systems, embedded processors, interface controllers, and test equipment. The integrated PLL architecture is relevant when the circuit needs a regenerated clock rather than a passive fanout buffer. Designers should compare both source and destination clock requirements, verify the supported output configuration, and check propagation-delay behavior across temperature and supply voltage before using the device as a drop-in element in an existing design. The most important layout consideration is short, controlled clock routing. Keep the input and output paths away from noisy switching nodes, use a continuous ground reference, and terminate unused outputs according to the manufacturer recommendations. The available search results do not provide a verified pricing schedule, complete pin mapping, lifecycle statement, or detailed electrical limits; those fields remain explicitly marked for data acquisition rather than being inferred. This page combines the verified Renesas and distributor classifications with practical clock-distribution guidance, package information, sourcing references, and an explicit data-completeness assessment. It is intended to support initial component selection while distinguishing confirmed specifications from parameters that must still be checked in the official datasheet.

RFQ پەیوەندی
MK2302S-01ILF - 168MHz PLL Zero Delay Buffer | Renesas
MK2302S-01ILF

MK2302S-01ILF - 168MHz PLL Zero Delay Buffer | Renesas

Renesas MK2302S-01ILF is a PLL-based clock multiplier and zero delay buffer (ZDB) with one true CMOS output, rated up to 168 MHz from a 3.15 V to 3.45 V supply, and housed in an 8-pin SOIC (0.154 in / 3.90 mm wide) surface-mount package with 175 ps output skew. A zero delay buffer is a clock distribution device whose output edge is phase-aligned with the reference edge presented at its input, so the buffer adds essentially no propagation delay to the clock it regenerates. In the signal-chain hierarchy it sits below clock buffers, below clock generators, and ultimately below clock and timing ICs used for system-wide frequency management. The MK2302S-01ILF belongs to the Renesas ClockBlocks family, which was created to meet higher-speed, lower-voltage clocking requirements in modern digital systems. Key features include a maximum operating frequency of 168 MHz, a narrow 3.15 V to 3.45 V CMOS supply range, a single non-inverted output, and 175 ps output skew, making it suitable for designs that need a small, low-power fan-out or jitter-cleaning stage near a high-speed load. The part is a surface-mount device in the 8-pin SOIC (PDSO8, 0.15 inch) package, so it drops into standard fine-pitch SOIC-8 land patterns with no exposed pad and no special thermal considerations. Internally, the device combines proprietary analog/digital phase-locked loop techniques with a regenerative buffer stage. The PLL-based approach lets the output edge track the rising edge of the input reference clock while the buffer restores edge rate and amplitude, which is preferable to relying on a plain CMOS buffer when duty-cycle distortion and jitter have accumulated over long distribution paths. Typical uses include CPU and SoC reference clock distribution, FPGA and ASIC clocking for networking switches, memory-interface reference clocking, and instrumentation front ends where a low-jitter, phase-aligned reference is needed at the far end of a board. When laying out the board, keep the reference clock trace short and match the input and output trace lengths where phase alignment to a distant load matters. Remember that a ZDB removes buffer delay, not board skew, so length matching still governs arrival-time accuracy at the destination. This page combines the electrical ratings, package data, drop-in alternatives, comparison tables, and practical layout guidance for the MK2302S-01ILF into a single engineering reference that goes beyond a distributor listing page.

RFQ پەیوەندی
MK2302S-01LF 168MHz Zero Delay Clock Buffer | Renesas
MK2302S-01LF

MK2302S-01LF 168MHz Zero Delay Clock Buffer | Renesas

The Renesas Electronics MK2302S-01LF is a clock multiplier and zero-delay buffer (ZDB) integrated circuit operating at 168 MHz in an 8-pin SOIC package. It is designed for clock distribution and frequency multiplication applications where low propagation delay and controlled clock skew are important. The device uses CMOS bus technology and operates from a 3.15 V to 3.45 V supply, making it suitable for systems using a 3.3 V clock domain. A zero-delay buffer is a clock-integrity device that reproduces an input clock at its outputs while minimizing the delay between the input transition and the corresponding output transition. The MK2302S-01LF combines Renesas proprietary analog/digital phase-locked-loop techniques with clock-buffer functionality. The device is part of the ClockBlocks family and is intended for higher-speed, lower-voltage clocking requirements. The MK2302S-01LF supports a maximum clock frequency of 168 MHz and has a specified output skew of 175 ps. Its 8-SOIC surface-mount package is identified as approximately 0.154 inches, or 3.90 mm, wide. The operating temperature range is listed as 0°C to 70°C, and the device is categorized as a clock-driver IC with a CMOS bus interface. Typical applications include processor and controller clock distribution, data-converter clocking, communications-interface clocking, and general-purpose digital systems requiring a multiplied or buffered clock. In these systems, the device can provide a more controlled clock signal to multiple loads while helping reduce the timing uncertainty associated with directly distributing a high-speed source clock. The primary design consideration is maintaining the specified 3.15 V to 3.45 V supply range and accounting for the 175 ps output skew in the receiving circuitry. Decoupling should be placed close to the supply pins, and the SOIC footprint should follow the manufacturer's recommended layout for the ClockBlocks zero-delay-buffer family. This page combines the Renesas family information, technical characteristics, package details, sourcing guidance, drop-in replacement information, and practical implementation notes for engineers evaluating the MK2302S-01LF.

RFQ پەیوەندی
MK2302S-01TR - 168MHz Zero-Delay Clock Buffer | Renesas (Tape & Reel)
MK2302S-01TR

MK2302S-01TR - 168MHz Zero-Delay Clock Buffer | Renesas (Tape & Reel)

The Renesas Electronics MK2302S-01TR is a 168 MHz zero-delay buffer (ZDB) with an integrated analog/digital phase-locked loop, supplied in an 8-pin SOIC package. It provides one clock circuit, a CMOS clock output, and operates from a verified 3.15 V to 3.45 V supply range. The device is designed to regenerate and distribute clock signals where predictable frequency, controlled phase relationship, and multiple output drive capability are required. A zero-delay buffer is a clock-management device intended to reproduce an input clock at one or more outputs while controlling propagation delay and phase relationship. The MK2302S-01TR uses PLL techniques to distribute a clock signal and can therefore be useful in systems where the source clock must be isolated or regenerated before reaching multiple sequential or communications circuits. In the system hierarchy, it belongs to the clock and timing IC family rather than a general-purpose logic IC. Verified device characteristics include a maximum frequency of 168 MHz, one clock circuit, a CMOS output, and a 3.15 V to 3.45 V supply range. The manufacturer and distributor search results identify the part as a multiplier and zero-delay buffer. Additional timing, output-current, jitter, temperature, and package-dimension values were not supplied in the verified data and therefore require confirmation from the manufacturer datasheet before final design release. Typical uses include clock distribution for communications equipment, digital logic systems, embedded processors, interface controllers, and test equipment. The integrated PLL architecture is relevant when the circuit needs a regenerated clock rather than a passive fanout buffer. Designers should compare both source and destination clock requirements, verify the supported output configuration, and check propagation-delay behavior across temperature and supply voltage before using the device as a drop-in element in an existing design. The most important layout consideration is short, controlled clock routing. Keep the input and output paths away from noisy switching nodes, use a continuous ground reference, and terminate unused outputs according to the manufacturer recommendations. The available search results do not provide a verified pricing schedule, complete pin mapping, lifecycle statement, or detailed electrical limits; those fields remain explicitly marked for data acquisition rather than being inferred. This page combines the verified Renesas and distributor classifications with practical clock-distribution guidance, package information, sourcing references, and an explicit data-completeness assessment. It is intended to support initial component selection while distinguishing confirmed specifications from parameters that must still be checked in the official datasheet.

RFQ پەیوەندی
MK2304S-1ILF - 133MHz Zero-Delay Buffer | Renesas
MK2304S-1ILF

MK2304S-1ILF - 133MHz Zero-Delay Buffer | Renesas

The Renesas Electronics MK2304S-1ILF is a 133 MHz zero-delay buffer in an 8-pin SOIC package, designed to distribute a periodic clock signal while compensating for propagation-delay differences between the source and destination circuits. It provides one clock-buffer channel and is categorized as a low-skew clock and timing IC. A zero-delay buffer is a clock-management device that reproduces an input clock at an output with very little added delay. It sits between a clock source and a load when the system needs a clean, repeatable clock distribution point rather than the longer and less deterministic delay of ordinary buffered wiring. In the broader semiconductor hierarchy, this device is a clock buffer, a type of clock and timing IC, and a member of the wider semiconductor and digital signal-conditioning product categories. The primary identified specifications are a maximum operating frequency of 133 MHz, one buffered output channel, and an 8-SOIC package measuring approximately 3.90 mm in width. The MK2304S-1ILF is identified as a low-skew zero-delay design, making it appropriate for systems that distribute a periodic reference clock to multiple logic or communications circuits. The -1ILF ordering code identifies the specific manufacturer configuration rather than a generic clock-buffer function. Unlike a crystal oscillator, the MK2304S-1ILF does not create a frequency; it preserves and redistributes an externally generated clock. Its zero-delay architecture can reduce the timing difference between a clock source and a remote receiver while avoiding the substantial clock-to-clock skew commonly encountered with ordinary logic buffers. The manufacturer classification of the part as a low-skew clock buffer distinguishes it from general-purpose buffers and fan-out devices. Typical uses include processor clock distribution, communications-interface clock conditioning, memory-interface clock routing, FPGA clock distribution, and general digital systems that require a stable periodic reference. The 133 MHz operating point makes it particularly relevant to designs operating below that clock rate while retaining a specified low-skew distribution function. When implementing the device, preserve the clock topology recommended by the Renesas Electronics datasheet and keep the clock trace away from noisy switching nodes. Account for package and board propagation delay when calculating timing margins. Confirm input slew, output loading, supply requirements, and operating-temperature limits against the manufacturer datasheet before release to production. This page combines the identified MK2304S-1ILF specifications with package-focused alternatives, comparison data, application guidance, and practical design notes. It is intended to help engineers evaluate clock-distribution requirements and identify the exact documentation needed for an auditable hardware design.

RFQ پەیوەندی
MK2304S-1ILFT - 133MHz Zero Delay Buffer | Renesas
MK2304S-1ILFT

MK2304S-1ILFT - 133MHz Zero Delay Buffer | Renesas

The Renesas Electronics MK2304S-1ILFT is a 133 MHz zero-delay, low-skew CMOS clock buffer with PLL capability, packaged in an 8-SOIC measuring 3.90 mm in width. It is designed to reproduce clock signals with minimal propagation delay while controlling skew between outputs, making it suitable for synchronizing digital logic, processors, memory interfaces, and other clocked subsystems. A zero-delay buffer is a clock-management integrated circuit that compensates for the propagation delay introduced by clock routing. It belongs to the clock buffer family within clock and timing ICs, where buffer, driver, and PLL-based devices distribute high-speed reference clocks across a system. The MK2304S-1ILFT combines one clock circuit, a clock input, CMOS outputs, and PLL capability in a surface-mount package. The device supports operation to 133 MHz and is identified as a low-skew zero-delay buffer. These characteristics are significant in systems where multiple loads must receive closely related clock transitions. The 8-SOIC package provides a compact surface-mount solution for PCB designs that require more than a passive delay element but do not need the functional complexity of a general-purpose clock generator. In the digital signal path, the buffer accepts a clock signal and provides a corresponding CMOS clock output. Its zero-delay architecture is intended to preserve system timing relationships more effectively than ordinary logic-buffer routing, where cumulative gate and trace delay can shift clock arrival times. PLL capability provides an additional clock-related function, although operating mode, feedback topology, and configuration details must be established from the manufacturer datasheet. Typical applications include clock distribution for communications equipment, processor and memory clock interfaces, embedded control systems, industrial automation, and consumer electronics. The 133 MHz maximum operating frequency makes the device relevant to legacy and established digital platforms rather than the highest-speed contemporary processor interfaces. The 3.90 mm-wide SOIC package also supports conventional surface-mount assembly and repair workflows. PCB implementation should preserve a short, symmetric clock path between the source, buffer, and receiving circuits. Place the device close to the clock source or load it is intended to buffer, use a continuous ground reference, and avoid routing the clock through test pads or long parallel segments where avoidable. Decoupling capacitors should be positioned close to the supply and ground pins according to the manufacturer’s reference layout. This product page combines the manufacturer device description with application guidance, design considerations, and a structured comparison framework. It supports engineers evaluating the MK2304S-1ILFT for low-skew clock distribution, replacement planning, footprint verification, and PCB implementation in 8-SOIC designs.

RFQ پەیوەندی
MK2304S-1LF - 133MHz Zero-Delay Clock Buffer | Renesas
MK2304S-1LF

MK2304S-1LF - 133MHz Zero-Delay Clock Buffer | Renesas

Renesas Electronics MK2304S-1LF is a zero-delay, low-skew CMOS clock buffer with a maximum operating frequency of 133 MHz, a 1:4 input-to-output ratio, and one circuit in an 8-pin SOIC package measuring 0.154 inch, or 3.90 mm, in width. It is designed to reproduce and distribute clock signals where low propagation delay and controlled output skew are important to system timing. A zero-delay buffer is a clock and timing integrated circuit that reconstructs and buffers a periodic logic waveform while attempting to minimize added propagation delay. In the broader hierarchy, it belongs to clock buffers and drivers, then clock and timing ICs, then integrated circuits and semiconductors. Unlike a passive fan-out buffer, it combines active input and output stages with circuitry designed to preserve clock-edge relationships and provide useful drive capability. Verified distributor information identifies the MK2304S-1LF as a zero-delay buffer with a maximum frequency of 133 MHz, a single circuit, a 1:4 input-to-output ratio, CMOS output technology, and PLL capability. Its 8-SOIC package supports conventional surface-mount assembly, while the -1LF ordering suffix identifies the lead-free packaging configuration. These characteristics make the device relevant to clock-distribution networks, processor and memory interfaces, communication equipment, and general digital systems requiring multiple or isolated clock outputs. The active circuit is intended to reduce loading on the source clock and distribute a clean CMOS waveform. A 1:4 ratio means the device provides four output phases for each input cycle, which is useful when several downstream blocks must receive related clocks. The exact propagation-delay, output-skew, rise-time, fall-time, supply-current, and operating-temperature limits must be confirmed in the Renesas manufacturer datasheet before a design is released. Typical uses include processor clock distribution, memory clock buffering, communication-interface clock fan-out, and digital test-equipment clock trees. In each case, the key design concern is preserving edge-to-edge relationships while keeping source loading and interconnect-induced skew under control. The 133 MHz upper frequency provides a useful qualification point for legacy and moderate-speed digital systems. Designers should place the device close to the clock source, use short and properly terminated clock traces, and verify the output timing at the receiving endpoints rather than relying only on device-level specifications. Decoupling and return-path continuity are also essential because inductive power-supply noise and imperfect grounding can degrade deterministic clock quality. This page consolidates the verified distributor specifications, current sourcing information, package details, selection guidance, and design cautions for the MK2304S-1LF. It also distinguishes verified drop-in candidates from unverified package or frequency assumptions so engineers can make a defensible replacement decision.

RFQ پەیوەندی
MK2304S-1LFT - 133MHz Zero-Delay Buffer | Renesas
MK2304S-1LFT

MK2304S-1LFT - 133MHz Zero-Delay Buffer | Renesas

The Renesas Electronics MK2304S-1LFT is a zero-delay, low-skew clock buffer based on PLL technology, operating up to 133 MHz in an 8-SOIC package. It accepts a clock input and provides a CMOS output through one buffer circuit. The device is intended for high-speed digital systems where clock distribution, edge alignment, and reduced propagation delay are important design objectives. Its 3.3 V supply operation makes it suitable for systems using 3 V to 3.6 V clock domains. A zero-delay buffer is a clock and timing integrated circuit that uses phase-locked-loop techniques to reproduce a clock edge with very low delay. Unlike a passive buffer, it can compensate for clock distribution delay and provide a stable, low-skew output for sequential logic. The MK2304S-1LFT is therefore positioned within the clock buffer, PLL, and clock-generation hierarchy, where it supports high-speed clock routing across a board or between functional blocks. The main electrical characteristics identify the part as a 133 MHz maximum-frequency, single-circuit clock buffer with CMOS output. Its 8-SOIC package provides a compact surface-mount implementation with a stated body width of 3.90 mm. The zero-delay architecture is particularly useful when the clock must reach multiple circuits without introducing significant edge-to-edge timing variation. Its single output arrangement makes it straightforward to use where one buffered clock reference is required rather than a multi-output fanout network. Typical applications include processor and FPGA clock conditioning, memory interface clock distribution, communications equipment, test and measurement systems, and other digital platforms operating below or at 133 MHz. In these systems, the buffer can isolate or reshape a source clock while preserving the timing relationship needed by downstream logic. The 3.3 V CMOS operating environment also allows integration with common 3.3 V digital logic families when timing, voltage, and loading conditions are checked together. Designers should verify input clock amplitude, rise and fall times, output loading, board skew, and downstream input thresholds against the manufacturer datasheet. The package requires normal decoupling and careful clock routing, while transmission-line effects may become relevant on longer traces. This page combines the verified device identity, package information, timing role, drop-in reference information, and practical selection guidance for engineers evaluating the MK2304S-1LFT in clock-distribution designs.

RFQ پەیوەندی
MK2304S-2 - 133MHz Zero-Delay Buffer | Renesas | Clock
MK2304S-2

MK2304S-2 - 133MHz Zero-Delay Buffer | Renesas | Clock

The Renesas Electronics MK2304S-2 is a 133 MHz zero-delay buffer with one CMOS clock circuit in an 8-SOIC package measuring 0.154 inch, or 3.90 mm, wide. It uses PLL-based zero-delay technology to reproduce a clock signal with low skew, and the verified specifications identify a 1:1 input-to-output ratio. The device operates from a 3 V to 3.6 V supply and supports a 0°C to 70°C temperature range, making it suitable for conventional digital clock-distribution systems that fit those limits. A zero-delay buffer is a clock and timing IC that compensates clock-propagation delay between a source and downstream circuitry while maintaining a unity frequency relationship between input and output. Within the broader semiconductor hierarchy, it belongs to clock and timing integrated circuits and is functionally associated with clock buffers, clock drivers, and PLL-based synchronization circuits. Its principal engineering benefit is reduced clock skew among receiving devices, provided the power supply, trace topology, and output loading meet the manufacturer's operating requirements. The MK2304S-2 provides a maximum frequency of 133 MHz, one CMOS output path, PLL capability, and a unity input-to-output ratio. The verified data describes it as a low-jitter, low-skew, high-performance PLL-based buffer for high-speed applications. These characteristics make clock-edge alignment more important than merely restoring a degraded waveform. Designers must also account for supply decoupling, output loading, board-level skew, and the fact that the specified operating temperature is limited to 0°C through 70°C. Its 8-SOIC surface-mount package supports conventional PCB assembly and compact clock-distribution layouts. The verified operating information specifies a 3 V to 3.6 V supply, CMOS output, and one circuit. Exact propagation delay, input and output capacitance, output current, RMS jitter, cycle-to-cycle jitter, and package dimensions beyond the stated width are not available in the supplied records and must be checked in the manufacturer documentation before release to production. Typical uses include synchronizing CMOS logic, distributing a common clock among digital components, correcting accumulated board or driver skew, and buffering a clock source in communications, control, or embedded systems. The 133 MHz ceiling makes timing closure critical: propagation delay, output transition behavior, loading, and PCB mismatch can all affect whether the buffer preserves the required edge relationship. For implementation, follow the manufacturer's recommended 0.1 µF decoupling capacitor from VDD to GND and place it as close as practical to the device. Confirm source and sink capability against the target load, preserve a continuous ground reference, and validate worst-case skew at the actual operating temperature. Do not assume automotive or extended-temperature suitability because the verified range is 0°C to 70°C. This page combines verified distributor specifications, the manufacturer datasheet link, commercial availability signals, and a cross-brand replacement assessment. It also separates confirmed electrical facts from parameters that still require datasheet verification, helping engineers evaluate the MK2304S-2 without treating unverified timing, jitter, or current limits as guaranteed specifications.

RFQ پەیوەندی
MK2304S-2I - 133MHz Zero-Delay Buffer | Renesas
MK2304S-2I

MK2304S-2I - 133MHz Zero-Delay Buffer | Renesas

The Renesas Electronics MK2304S-2I is a PLL-based zero-delay buffer rated for clock frequencies up to 133 MHz at 3.3 V, with four low-skew CMOS outputs in an 8-SOIC surface-mount package. The -2I ordering code identifies the industrial-temperature device, while the package suffix S denotes the SOIC form factor. According to the available manufacturer description, it uses proprietary low-jitter PLL techniques to compensate propagation delay and provide tightly related outputs for high-speed digital systems. A zero-delay buffer is a clocking device that receives a reference clock and generates multiple buffered outputs intended to align edge timing. Unlike a simple logic buffer, a PLL-based zero-delay buffer can retime the input waveform while distributing it to several loads. In the clock and timing hierarchy, the MK2304S-2I is a clock buffer, a clock-distribution component, and ultimately a timing integrated circuit used to reduce skew between digital destinations. The verified source data identifies the device as a low-jitter, low-skew, high-performance PLL-based zero-delay buffer operating at 3.3 V. It provides four low-skew outputs and includes a bank of two outputs operating at one-half the input frequency. At speeds up to 133 MHz, these characteristics make the part relevant to processor clock trees, memory interfaces, communications equipment, and other systems where multiple clock domains require controlled edge relationships. The architecture is important because clock skew can determine setup and hold margins even when nominal frequency is acceptable. Four outputs allow a designer to distribute the reference to multiple loads, while the divided outputs can serve lower-rate clock domains. Zero-delay mode means the rising edge of the input clock is aligned with the corresponding outputs, although actual board-level timing still depends on trace length, load capacitance, supply integrity, and the receiving devices. Typical implementations include synchronous digital logic, networking equipment, industrial controllers, and communication systems. The 3.3 V supply requirement places it in systems that already provide a 3.3 V clocking rail. Designers should use short, impedance-controlled clock traces, maintain continuous return paths, and place decoupling close to the supply pins. Input and output timing, PLL loop behavior, and output loading should be evaluated with the complete system rather than inferred solely from the 133 MHz headline frequency. This product record combines verified distributor and manufacturer-linked specifications with practical clock-tree design guidance. It also distinguishes confirmed facts from unavailable details, preventing unsupported pin assignments, jitter numbers, pricing tiers, or lifecycle claims from being presented as established specifications. The result is intended to help engineers source the MK2304S-2I and evaluate whether its zero-delay, four-output architecture matches a specific synchronous design.

RFQ پەیوەندی
MK2304S-2ILF - 133MHz 3.3V PLL Zero Delay Buffer | Renesas
MK2304S-2ILF

MK2304S-2ILF - 133MHz 3.3V PLL Zero Delay Buffer | Renesas

The Renesas Electronics MK2304S-2ILF is a PLL-based zero delay buffer clock IC that delivers four low-skew outputs to 133 MHz from a single 3.3 V supply, housed in an 8-pin SOIC package measuring 0.154 in (3.90 mm) wide. It eliminates propagation delay between the reference clock and the driven outputs while holding output-to-output skew tightly under control, and it includes a bank of two outputs that operate at 1/2X the input frequency. A zero delay buffer is a clock distribution device that regenerates a clock through an internal phase-locked loop rather than passing it through a simple buffer. Because the output edge is re-timed by the PLL instead of following the input edge through a fixed propagation delay, the device can drive multiple loads across a board while presenting a single, consistent clock reference to the receiver. In the zero delay mode of operation, the rising edge of the input clock appears at the outputs with essentially no added latency, which matters when source-synchronous interfaces must be aligned. Key features of the MK2304S-2ILF include a maximum operating frequency of 133 MHz at 3.3 V, four independent low-skew outputs, and the dedicated 1/2X output bank for divide-by-two clocking without an external divider. The device is based on the manufacturer's proprietary low-jitter PLL techniques, which is the core technology that separates it from simple fan-out buffers in jitter performance. Internally, the PLL architecture re-times the reference clock and drives the output bank, so output edges depend on the internal loop rather than on logic gate delay. This gives cycle-to-cycle jitter that is independent of the number of loads on each output and largely independent of board loading, which is the primary reason designers move from a plain buffer to a PLL-based part when skew or jitter budgets are tight. Typical applications include networking and telecom line-card clock trees, server and storage backplane clock distribution, processor and FPGA clock fan-out, and general-purpose frequency multiplication or division for system timing. The 1/2X bank is useful in designs that need a divided clock for lower-speed peripherals alongside full-rate outputs for the main datapath. When designing around this device, treat the PLL as a sensitive analog block: route the reference clock over a short, continuous trace to pin 1, keep the supply decoupling capacitor close to the VDD pins, and leave the unused output channels terminated according to the datasheet guidance to avoid unnecessary dynamic current. Confirm the final edge budget in system, because board skew and load mismatch add to the device's own output skew. This page consolidates the manufacturer datasheet details, drop-in replacement candidates, comparison data and practical layout notes in one place, so you can qualify the part quickly and plan the clock tree before the first schematic review.

RFQ پەیوەندی
MK2304S-2ITR - 133MHz Zero-Delay Buffer | Renesas (Tape & Reel)
MK2304S-2ITR

MK2304S-2ITR - 133MHz Zero-Delay Buffer | Renesas (Tape & Reel)

The Renesas Electronics MK2304S-2ITR is a PLL-based zero-delay buffer rated for clock frequencies up to 133 MHz at 3.3 V, with four low-skew CMOS outputs in an 8-SOIC surface-mount package. The -2I ordering code identifies the industrial-temperature device, while the package suffix S denotes the SOIC form factor. According to the available manufacturer description, it uses proprietary low-jitter PLL techniques to compensate propagation delay and provide tightly related outputs for high-speed digital systems. A zero-delay buffer is a clocking device that receives a reference clock and generates multiple buffered outputs intended to align edge timing. Unlike a simple logic buffer, a PLL-based zero-delay buffer can retime the input waveform while distributing it to several loads. In the clock and timing hierarchy, the MK2304S-2ITR is a clock buffer, a clock-distribution component, and ultimately a timing integrated circuit used to reduce skew between digital destinations. The verified source data identifies the device as a low-jitter, low-skew, high-performance PLL-based zero-delay buffer operating at 3.3 V. It provides four low-skew outputs and includes a bank of two outputs operating at one-half the input frequency. At speeds up to 133 MHz, these characteristics make the part relevant to processor clock trees, memory interfaces, communications equipment, and other systems where multiple clock domains require controlled edge relationships. The architecture is important because clock skew can determine setup and hold margins even when nominal frequency is acceptable. Four outputs allow a designer to distribute the reference to multiple loads, while the divided outputs can serve lower-rate clock domains. Zero-delay mode means the rising edge of the input clock is aligned with the corresponding outputs, although actual board-level timing still depends on trace length, load capacitance, supply integrity, and the receiving devices. Typical implementations include synchronous digital logic, networking equipment, industrial controllers, and communication systems. The 3.3 V supply requirement places it in systems that already provide a 3.3 V clocking rail. Designers should use short, impedance-controlled clock traces, maintain continuous return paths, and place decoupling close to the supply pins. Input and output timing, PLL loop behavior, and output loading should be evaluated with the complete system rather than inferred solely from the 133 MHz headline frequency. This product record combines verified distributor and manufacturer-linked specifications with practical clock-tree design guidance. It also distinguishes confirmed facts from unavailable details, preventing unsupported pin assignments, jitter numbers, pricing tiers, or lifecycle claims from being presented as established specifications. The result is intended to help engineers source the MK2304S-2ITR and evaluate whether its zero-delay, four-output architecture matches a specific synchronous design.

RFQ پەیوەندی
MK2304S-2LF - 133MHz Zero-Delay Clock Buffer | Renesas
MK2304S-2LF

MK2304S-2LF - 133MHz Zero-Delay Clock Buffer | Renesas

The Renesas Electronics MK2304S-2LF is a 133 MHz zero-delay, low-skew clock buffer with four CMOS outputs, a 3 V to 3.6 V supply range, and 400 ps skew in an 8-pin SOIC package measuring 3.90 mm wide. It uses PLL-based zero-delay buffering to support high-speed systems requiring closely matched clock outputs and low propagation delay. A zero-delay buffer is a clock and timing IC that compensates for clock-distribution path delay so multiple downstream devices can receive a common edge at approximately the same time. Within the product hierarchy, it is a clock buffer, a type of clock and timing integrated circuit and a specialized form of digital signal buffer. Unlike a conventional CMOS buffer, which introduces propagation delay, a PLL-based zero-delay buffer uses phase control to minimize delay through the device. The MK2304S-2LF operates from 3 V to 3.6 V and supports operation up to 133 MHz. Its four low-skew CMOS outputs allow one input clock to feed several loads while limiting output-to-output timing variation. The device is identified as a clock driver with a 1:1 input-to-output ratio, making it suitable for distributed clocking rather than frequency multiplication or division. Its SOIC-8 surface-mount package also supports conventional automated board assembly. Technically, the key benefit is the combination of low skew and zero-delay behavior at 133 MHz. The specified 400 ps skew provides a quantitative limit for output timing alignment, while the PLL-based architecture reduces insertion delay through the buffer. This is useful when several high-speed loads must be clocked consistently without allowing fanout traces or loading to create unacceptable arrival-time differences. Typical uses include processor and memory clock distribution, communications equipment, graphics systems, peripheral clocking, and other digital systems operating at or below 133 MHz. The four-output configuration can reduce the number of separate clock-buffer circuits required when four related loads share the same source clock. Care should be taken to maintain controlled-impedance routing and provide proper decoupling close to the device. Designers should verify output loading, trace length matching, supply-noise sensitivity, and unused-output termination against the manufacturer datasheet. Because the supplied web data does not include a complete pin table or guaranteed electrical limits for every parameter, those details should be confirmed in the manufacturer documentation before layout release. This page consolidates the verified 133 MHz operating point, 3 V to 3.6 V supply range, four-output PLL architecture, 400 ps skew, package information, RoHS indication, distributor availability, and drop-in replacement findings into a design-oriented component reference.

RFQ پەیوەندی
MK2304S-2LFTR - 133MHz Zero-Delay Clock Buffer | Renesas (Tape & Reel)
MK2304S-2LFTR

MK2304S-2LFTR - 133MHz Zero-Delay Clock Buffer | Renesas (Tape & Reel)

The Renesas Electronics MK2304S-2LFTR is a 133 MHz zero-delay, low-skew clock buffer with four CMOS outputs, a 3 V to 3.6 V supply range, and 400 ps skew in an 8-pin SOIC package measuring 3.90 mm wide. It uses PLL-based zero-delay buffering to support high-speed systems requiring closely matched clock outputs and low propagation delay. A zero-delay buffer is a clock and timing IC that compensates for clock-distribution path delay so multiple downstream devices can receive a common edge at approximately the same time. Within the product hierarchy, it is a clock buffer, a type of clock and timing integrated circuit and a specialized form of digital signal buffer. Unlike a conventional CMOS buffer, which introduces propagation delay, a PLL-based zero-delay buffer uses phase control to minimize delay through the device. The MK2304S-2LFTR operates from 3 V to 3.6 V and supports operation up to 133 MHz. Its four low-skew CMOS outputs allow one input clock to feed several loads while limiting output-to-output timing variation. The device is identified as a clock driver with a 1:1 input-to-output ratio, making it suitable for distributed clocking rather than frequency multiplication or division. Its SOIC-8 surface-mount package also supports conventional automated board assembly. Technically, the key benefit is the combination of low skew and zero-delay behavior at 133 MHz. The specified 400 ps skew provides a quantitative limit for output timing alignment, while the PLL-based architecture reduces insertion delay through the buffer. This is useful when several high-speed loads must be clocked consistently without allowing fanout traces or loading to create unacceptable arrival-time differences. Typical uses include processor and memory clock distribution, communications equipment, graphics systems, peripheral clocking, and other digital systems operating at or below 133 MHz. The four-output configuration can reduce the number of separate clock-buffer circuits required when four related loads share the same source clock. Care should be taken to maintain controlled-impedance routing and provide proper decoupling close to the device. Designers should verify output loading, trace length matching, supply-noise sensitivity, and unused-output termination against the manufacturer datasheet. Because the supplied web data does not include a complete pin table or guaranteed electrical limits for every parameter, those details should be confirmed in the manufacturer documentation before layout release. This page consolidates the verified 133 MHz operating point, 3 V to 3.6 V supply range, four-output PLL architecture, 400 ps skew, package information, RoHS indication, distributor availability, and drop-in replacement findings into a design-oriented component reference.

RFQ پەیوەندی
MK2304S-2TR - 133MHz Zero-Delay Buffer | Renesas | Clock (Tape & Reel)
MK2304S-2TR

MK2304S-2TR - 133MHz Zero-Delay Buffer | Renesas | Clock (Tape & Reel)

The Renesas Electronics MK2304S-2TR is a 133 MHz zero-delay buffer with one CMOS clock circuit in an 8-SOIC package measuring 0.154 inch, or 3.90 mm, wide. It uses PLL-based zero-delay technology to reproduce a clock signal with low skew, and the verified specifications identify a 1:1 input-to-output ratio. The device operates from a 3 V to 3.6 V supply and supports a 0°C to 70°C temperature range, making it suitable for conventional digital clock-distribution systems that fit those limits. A zero-delay buffer is a clock and timing IC that compensates clock-propagation delay between a source and downstream circuitry while maintaining a unity frequency relationship between input and output. Within the broader semiconductor hierarchy, it belongs to clock and timing integrated circuits and is functionally associated with clock buffers, clock drivers, and PLL-based synchronization circuits. Its principal engineering benefit is reduced clock skew among receiving devices, provided the power supply, trace topology, and output loading meet the manufacturer's operating requirements. The MK2304S-2TR provides a maximum frequency of 133 MHz, one CMOS output path, PLL capability, and a unity input-to-output ratio. The verified data describes it as a low-jitter, low-skew, high-performance PLL-based buffer for high-speed applications. These characteristics make clock-edge alignment more important than merely restoring a degraded waveform. Designers must also account for supply decoupling, output loading, board-level skew, and the fact that the specified operating temperature is limited to 0°C through 70°C. Its 8-SOIC surface-mount package supports conventional PCB assembly and compact clock-distribution layouts. The verified operating information specifies a 3 V to 3.6 V supply, CMOS output, and one circuit. Exact propagation delay, input and output capacitance, output current, RMS jitter, cycle-to-cycle jitter, and package dimensions beyond the stated width are not available in the supplied records and must be checked in the manufacturer documentation before release to production. Typical uses include synchronizing CMOS logic, distributing a common clock among digital components, correcting accumulated board or driver skew, and buffering a clock source in communications, control, or embedded systems. The 133 MHz ceiling makes timing closure critical: propagation delay, output transition behavior, loading, and PCB mismatch can all affect whether the buffer preserves the required edge relationship. For implementation, follow the manufacturer's recommended 0.1 µF decoupling capacitor from VDD to GND and place it as close as practical to the device. Confirm source and sink capability against the target load, preserve a continuous ground reference, and validate worst-case skew at the actual operating temperature. Do not assume automotive or extended-temperature suitability because the verified range is 0°C to 70°C. This page combines verified distributor specifications, the manufacturer datasheet link, commercial availability signals, and a cross-brand replacement assessment. It also separates confirmed electrical facts from parameters that still require datasheet verification, helping engineers evaluate the MK2304S-2TR without treating unverified timing, jitter, or current limits as guaranteed specifications.

RFQ پەیوەندی
MK2308G-1H - 133MHz 1:8 Zero Delay Buffer | Renesas
MK2308G-1H

MK2308G-1H - 133MHz 1:8 Zero Delay Buffer | Renesas

The Renesas Electronics MK2308G-1H is a 133 MHz zero-delay buffer with a 1:8 input-to-output ratio, PLL bypass capability, CMOS clock outputs, and eight low-skew outputs in a 16-TSSOP package. It is designed to distribute one clock input across eight outputs at speeds up to 133 MHz while operating from 3.3 V. The part can generate outputs through its PLL for zero-delay operation or bypass the PLL and route the input directly for testing. A zero-delay buffer is a clock and timing IC that compensates propagation delay introduced by clock distribution networks while distributing a single reference to multiple loads. It belongs to the broader hierarchy of clock buffers, clock distribution circuits, phase-locked-loop timing devices, and clock and timing integrated circuits. Its principal purpose is to provide multiple low-skew clock outputs to processors, memory interfaces, communications equipment, and other digital systems that require synchronized logic. The verified data identifies the MK2308G-1H as a zero-delay buffer IC with a maximum frequency of 133 MHz, one circuit, a 1:8 ratio, PLL functionality with bypass, clock input, and CMOS output. A distributor listing identifies the physical package as 16-TSSOP with a stated body width of 4.40 mm. The device can also drive its outputs in tri-state or stop them at a low level, useful for shared-bus and test-control architectures. Its PLL-based architecture is intended for low-skew output generation at 3.3 V. The bypass path allows the input clock to be observed without PLL multiplication or correction, which can simplify diagnostic and test setups. The output count enables one reference clock to feed eight destinations without replicating the clock source eight times, reducing routing complexity and helping maintain consistent timing across a board. Typical applications include processor clock distribution, memory clock fanout, communications infrastructure, test-and-measurement equipment, and digital systems requiring multiple synchronized outputs. When implementing the circuit, use the manufacturer-recommended decoupling capacitors and place them close to the power and ground pins. The Renesas MK2308-1H datasheet search result specifies 0.01 mF capacitors between VDD and GND at the stated power-pin pairs. This product page synthesizes the verified distributor specifications, manufacturer datasheet link, package information, and practical implementation guidance. Because the supplied source snippets do not expose complete electrical limit tables or a complete verified pin map, unspecified values are marked as [DATA_NEEDED] rather than inferred.

RFQ پەیوەندی
MK2308G-1HI - 133MHz Zero-Delay Buffer | Renesas Electronics
MK2308G-1HI

MK2308G-1HI - 133MHz Zero-Delay Buffer | Renesas Electronics

Renesas Electronics MK2308G-1HI is a 133 MHz zero-delay buffer with PLL bypass, one clock circuit, and CMOS output in a 16-pin TSSOP package. It operates from 3 V to 3.6 V, making it a 3.3 V clock-distribution component for systems requiring regenerated, low-skew clock signals. The device can source a clock directly from its input for testing or use its PLL-based zero-delay function for normal operation. A zero-delay buffer is a clock-and-timing IC that receives a reference clock and redistributes it through a phase-locked loop or equivalent edge-alignment architecture. The zero-delay designation indicates that the device compensates propagation delay between the reference input and its outputs so downstream circuits can receive closely aligned clock edges. Within the broader hierarchy, the MK2308G-1HI is a clock buffer, which is a clock-and-timing IC and, ultimately, a semiconductor used for system clock distribution and phase alignment. The principal verified features are a maximum operating frequency of 133 MHz, a 3 V to 3.6 V supply range, CMOS clock outputs, and PLL operation with bypass. The single-circuit configuration is useful when a board requires one regenerated clock rather than several independently buffered outputs. Its 16-pin TSSOP package is compatible with conventional surface-mount assembly, while its 4.40 mm stated package width supports compact PCB layouts where the TSSOP mechanical envelope is acceptable. The PLL-based architecture separates the reference source from the distributed clock output and enables zero-delay clock regeneration. PLL bypass provides a direct-input test path that can assist board bring-up and fault isolation. Actual timing performance depends on input-clock stability, output loading, trace geometry, supply integrity, and the selected operating mode, so engineers should consult the Renesas datasheet and evaluate the complete clock path rather than relying on the maximum frequency alone. Typical uses include processor and FPGA clock distribution, memory-interface clock support, communications equipment, industrial control systems, and test-and-measurement instruments. The part is particularly relevant to 3.3 V designs where a regenerated clock is needed to improve edge alignment or isolate a clock source from downstream loading. In each case, trace length matching, return-path continuity, and output-load budgeting remain important implementation considerations. For a new layout, reserve the TSSOP land pattern, route the reference clock away from high-current switching nodes, and provide the decoupling arrangement specified by the manufacturer. If the PCB cannot support controlled clock topology, replacing the device without changing routing may not resolve timing or signal-integrity issues. Confirm operating mode, load, frequency, and package details against the current Renesas documentation before release. This page consolidates verified distributor specifications, manufacturer datasheet information, practical clock-design guidance, and honestly qualified replacement references. It separates confirmed drop-in candidates from merely similar devices, helping engineers compare package and lifecycle constraints without treating cross-reference search results as guaranteed equivalents.

RFQ پەیوەندی
MK2308G-1HILF - 133MHz Zero Delay Buffer | Renesas
MK2308G-1HILF

MK2308G-1HILF - 133MHz Zero Delay Buffer | Renesas

The Renesas Electronics MK2308G-1HILF is a 3.3 V zero-delay clock buffer with a maximum operating frequency of 133 MHz, one clock circuit, and PLL operation with bypass support. The device accepts a clock input, produces CMOS-compatible outputs, and is housed in a 16-pin TSSOP package measuring 0.173 inch wide by 0.173 inch long. A zero-delay buffer is a clock-integrity IC that uses an internal phase-locked loop to reproduce a clock while compensating for propagation delay through external routing. Its function hierarchy is zero-delay buffer, clock buffer, clock and timing IC, logic IC, and integrated circuit. Unlike a passive delay line, this device actively reconstructs its output clock, helping downstream circuits receive low-skew timing signals. The MK2308G-1HILF provides a 1:8 input-to-output ratio, CMOS output compatibility, and PLL bypass functionality. The bypass path is useful when the system does not require PLL-based phase adjustment. Its 133 MHz maximum frequency makes it suitable for clock distribution in communication, industrial control, computing, and test-and-measurement systems that operate below that frequency. Renesas describes the device as a 3.3 V low-skew clock buffer. The PLL architecture separates clock generation from input distribution, allowing the device to maintain controlled output timing when system traces and device delays would otherwise create skew between destinations. The 16-TSSOP package provides a compact surface-mount format compatible with standard PCB assembly processes. Typical applications include network-interface clock distribution, processor and peripheral clock routing, industrial control systems, communications equipment, and instrumentation. In these systems, the buffer can fan out one reference clock to multiple destinations while reducing the timing uncertainty introduced by unequal trace lengths. The primary design consideration is confirming that the intended input frequency, output-divider configuration, bypass state, and output loading remain within the manufacturer’s operating limits. PCB layout should minimize clock-trace mismatch and return clock and power grounds cleanly. Decoupling capacitors should be placed close to the supply pins according to the manufacturer’s recommended layout. This page consolidates the device’s key electrical characteristics, verified package information, a confirmed same-family replacement, practical clock-layout guidance, and an eight-parameter engineering comparison. It is designed to help engineers assess fit, replacement risk, and board-level implementation before committing to a design.

RFQ پەیوەندی