Clock & Timing
بەرهەمەکان (970+)
MK2308G-1HITR - 133MHz Zero-Delay Buffer | Renesas Electronics (Tape & Reel)
Renesas Electronics MK2308G-1HITR is a 133 MHz zero-delay buffer with PLL bypass, one clock circuit, and CMOS output in a 16-pin TSSOP package. It operates from 3 V to 3.6 V, making it a 3.3 V clock-distribution component for systems requiring regenerated, low-skew clock signals. The device can source a clock directly from its input for testing or use its PLL-based zero-delay function for normal operation. A zero-delay buffer is a clock-and-timing IC that receives a reference clock and redistributes it through a phase-locked loop or equivalent edge-alignment architecture. The zero-delay designation indicates that the device compensates propagation delay between the reference input and its outputs so downstream circuits can receive closely aligned clock edges. Within the broader hierarchy, the MK2308G-1HITR is a clock buffer, which is a clock-and-timing IC and, ultimately, a semiconductor used for system clock distribution and phase alignment. The principal verified features are a maximum operating frequency of 133 MHz, a 3 V to 3.6 V supply range, CMOS clock outputs, and PLL operation with bypass. The single-circuit configuration is useful when a board requires one regenerated clock rather than several independently buffered outputs. Its 16-pin TSSOP package is compatible with conventional surface-mount assembly, while its 4.40 mm stated package width supports compact PCB layouts where the TSSOP mechanical envelope is acceptable. The PLL-based architecture separates the reference source from the distributed clock output and enables zero-delay clock regeneration. PLL bypass provides a direct-input test path that can assist board bring-up and fault isolation. Actual timing performance depends on input-clock stability, output loading, trace geometry, supply integrity, and the selected operating mode, so engineers should consult the Renesas datasheet and evaluate the complete clock path rather than relying on the maximum frequency alone. Typical uses include processor and FPGA clock distribution, memory-interface clock support, communications equipment, industrial control systems, and test-and-measurement instruments. The part is particularly relevant to 3.3 V designs where a regenerated clock is needed to improve edge alignment or isolate a clock source from downstream loading. In each case, trace length matching, return-path continuity, and output-load budgeting remain important implementation considerations. For a new layout, reserve the TSSOP land pattern, route the reference clock away from high-current switching nodes, and provide the decoupling arrangement specified by the manufacturer. If the PCB cannot support controlled clock topology, replacing the device without changing routing may not resolve timing or signal-integrity issues. Confirm operating mode, load, frequency, and package details against the current Renesas documentation before release. This page consolidates verified distributor specifications, manufacturer datasheet information, practical clock-design guidance, and honestly qualified replacement references. It separates confirmed drop-in candidates from merely similar devices, helping engineers compare package and lifecycle constraints without treating cross-reference search results as guaranteed equivalents.
MK2308G-1HLF - 133MHz PLL Zero Delay Buffer, 8 Outputs | Renesas
The Renesas Electronics MK2308G-1HLF is a 3.3 V zero delay buffer (ZDB) clock IC built on IDT proprietary low-jitter PLL techniques, delivering eight low-skew clock outputs at speeds up to 133 MHz in a 16-pin SOIC package. It is a fan-out and clock-tree element rather than a single-ended logic buffer, so a single source clock can be replicated across eight domain-crossing-friendly outputs with minimal propagation delay. A zero delay buffer is a clock and timing IC that uses phase-locked-loop technology to regenerate an incoming clock and re-time its edges, so the buffered output edge arrives effectively coincident with the input edge instead of after a fixed logic delay. In the device hierarchy it sits under clock buffer > clock and timing IC > integrated circuit > semiconductor, and it is used wherever a design needs many phase-aligned copies of a single reference clock. Key features of the MK2308G-1HLF include eight low-skew outputs, a maximum operating frequency of 133 MHz at 3.3 V, CMOS-compatible outputs, an integrated PLL with a bypass mode for test and debug, and per-output tri-state or stop-clock capability for bus segmentation. Because the outputs are regenerated through the PLL, the buffer also offers low phase noise and jitter performance that a simple CMOS fan-out buffer cannot match at high fan-out ratios. Internally, the PLL is the core element: the reference clock is multiplied and phase-shifted so that output edges align closely with the input edge. The bypass path lets a test engineer or a system architect select direct (non-PLL) clock propagation for characterization, while the PLL path provides the low-skew, low-jitter behavior needed in production. The 16-SOIC outline is a standard 3.90 mm wide narrow body surface mount package, easing prototyping on common evaluation platforms. Typical applications include CPU and FPGA clock fan-out, memory interface clock distribution, telecommunication line-card clocking, industrial control data acquisition, video timing distribution, and any system that needs multiple low-skew copies of a 133 MHz or slower reference clock. When designing around this part, confirm that the reference clock amplitude and slew rate meet the input requirements, and use the bypass mode only for bench characterization because switching between PLL and bypass paths changes the output timing relationship. Keep the fan-out traces short and matched so that package and board skew do not dominate the device's own output-to-output skew. This page consolidates the manufacturer device description, distributor listing data, and engineering notes on PLL zero-delay buffer selection so you can evaluate the MK2308G-1HLF against other fan-out and clock-tree options without digging through multiple documents.
MK2308G-1HTR - 133MHz 1:8 Zero Delay Buffer | Renesas (Tape & Reel)
The Renesas Electronics MK2308G-1HTR is a 133 MHz zero-delay buffer with a 1:8 input-to-output ratio, PLL bypass capability, CMOS clock outputs, and eight low-skew outputs in a 16-TSSOP package. It is designed to distribute one clock input across eight outputs at speeds up to 133 MHz while operating from 3.3 V. The part can generate outputs through its PLL for zero-delay operation or bypass the PLL and route the input directly for testing. A zero-delay buffer is a clock and timing IC that compensates propagation delay introduced by clock distribution networks while distributing a single reference to multiple loads. It belongs to the broader hierarchy of clock buffers, clock distribution circuits, phase-locked-loop timing devices, and clock and timing integrated circuits. Its principal purpose is to provide multiple low-skew clock outputs to processors, memory interfaces, communications equipment, and other digital systems that require synchronized logic. The verified data identifies the MK2308G-1HTR as a zero-delay buffer IC with a maximum frequency of 133 MHz, one circuit, a 1:8 ratio, PLL functionality with bypass, clock input, and CMOS output. A distributor listing identifies the physical package as 16-TSSOP with a stated body width of 4.40 mm. The device can also drive its outputs in tri-state or stop them at a low level, useful for shared-bus and test-control architectures. Its PLL-based architecture is intended for low-skew output generation at 3.3 V. The bypass path allows the input clock to be observed without PLL multiplication or correction, which can simplify diagnostic and test setups. The output count enables one reference clock to feed eight destinations without replicating the clock source eight times, reducing routing complexity and helping maintain consistent timing across a board. Typical applications include processor clock distribution, memory clock fanout, communications infrastructure, test-and-measurement equipment, and digital systems requiring multiple synchronized outputs. When implementing the circuit, use the manufacturer-recommended decoupling capacitors and place them close to the power and ground pins. The Renesas MK2308-1H datasheet search result specifies 0.01 mF capacitors between VDD and GND at the stated power-pin pairs. This product page synthesizes the verified distributor specifications, manufacturer datasheet link, package information, and practical implementation guidance. Because the supplied source snippets do not expose complete electrical limit tables or a complete verified pin map, unspecified values are marked as [DATA_NEEDED] rather than inferred.
MK2308S-1H - 133MHz 8-Output Zero-Delay Buffer | Renesas
The Renesas Electronics MK2308S-1H is a PLL-based, eight-output CMOS zero-delay buffer rated to 133 MHz in a 16-SOIC surface-mount package. It operates from a 3.0 V to 3.6 V supply and provides eight low-skew outputs that can be sourced either through the PLL for zero-delay operation or directly from the input for testing. The verified device family information identifies 200 ps output skew and describes the part as a low-phase-noise, high-speed clock distribution device. A zero-delay buffer is a clock and timing IC that regenerates a reference clock through a phase-locked loop, compensating for clock-distribution delay while preserving frequency. In the hierarchy of electronic components, this device belongs to clock and timing integrated circuits, then PLL-based clock drivers, frequency-distribution circuits, and finally broader digital and power-management systems. It is used where multiple logic domains need closely related clock signals. Key verified features include a maximum clock frequency of 133 MHz, eight low-skew outputs, CMOS-compatible signaling, 3.0 V to 3.6 V operation, and selectable tri-state or stop-at-a-low output behavior. The PLL can be bypassed for testing or direct clock propagation. The available operating-temperature information identifies a 0°C to 70°C range, making the device suitable for commercial-temperature clock-distribution equipment. The low-skew output architecture helps maintain timing relationships across multiple destinations, which is important in networking, telecommunications, and computing systems. Its 3.3 V supply operation is compatible with systems designed around modern CMOS clock domains, while the SOIC package supports conventional surface-mount assembly and inspection. Typical uses include clock fan-out for communications equipment, synchronized digital logic, computing interfaces, test and measurement systems, and embedded control platforms. Designers should account for trace-length matching, output-enable control, bypass testing, and the required decoupling capacitors. The verified datasheet search result specifically calls for 0.01 uF capacitors near the device power pins. This page combines verified distributor and manufacturer information, cross-reference results, application guidance, and design considerations into an engineering-focused component record. It is intended to support purchasing decisions while clearly separating verified values from parameters requiring further datasheet confirmation.
MK2308S-1HI - 133MHz Zero Delay Buffer | Renesas | Clock IC
Renesas Electronics MK2308S-1HI is a PLL-based zero-delay buffer IC operating up to 133 MHz, with eight low-skew outputs and CMOS-compatible interfaces in a 16-pin SOIC package measuring 0.154 inches, or 3.90 mm, in width. Its verified supply-voltage range is 3 V to 3.6 V, and its specified industrial operating-temperature range is -40°C to 85°C. The device belongs to the clock-generator, PLL, frequency-synthesizer, and clock-buffer hierarchy within clock and timing ICs. A zero-delay buffer is a clock-distribution circuit that reproduces an input clock at multiple outputs while compensating for propagation delay through an internal phase-locked loop. It is used where a system must fan one clock source across several loads without introducing excessive output-to-output skew. The MK2308S-1HI can produce outputs from its PLL for zero-delay operation or directly from the input for testing. Its outputs can also be placed in tri-state or stopped-clock conditions, providing control functions useful in multi-domain clock trees. Key verified features include a maximum operating frequency of 133 MHz, eight outputs, one circuit, a PLL with bypass capability, and output skew of 200 ps. The CMOS bus interface supports integration with digital logic operating from the same 3.0 V to 3.6 V supply. The 16-SOIC surface-mount package provides a practical option for established through-hole-compatible board layouts and factory assembly processes. Technically, the device uses proprietary low-jitter PLL techniques to generate eight low-skew clock outputs. The PLL-based architecture is significant because it compensates for internal buffer propagation delay while distributing the clock. Direct-input bypass provides a diagnostic path for evaluating signal behavior without relying on the PLL-generated output mode. Output tri-state and stop-clock controls allow unused clock branches to be disabled or held according to system requirements. Typical applications include networking equipment, computing systems, telecommunications infrastructure, server clock trees, industrial control electronics, and communication modules. Its eight-output organization suits designs that must feed multiple clock domains, while the 133 MHz ceiling covers common legacy and industrial digital clocking requirements. The 3.3 V supply range also makes it suitable for systems whose logic rails are centered around 3.3 V. When laying out a circuit using the MK2308S-1HI, preserve short and symmetrical clock paths from the device to each destination and follow the manufacturer's decoupling and layout recommendations. Validate output timing at the receiver, especially when fanout, trace length, or capacitive loading changes. Because the verified data does not provide the complete pinout, output-enable truth table, or absolute timing limits, those details should be confirmed against the manufacturer datasheet before release. This page consolidates the verified Renesas and distributor information for the MK2308S-1HI, adds application-specific engineering context, identifies the available same-package comparison, and clearly separates confirmed specifications from parameters that still require datasheet verification.
MK2308S-1HILF - 133MHz 8-Output Zero-Delay Buffer | Renesas
Renesas Electronics MK2308S-1HILF is a 3.3 V, 133 MHz zero-delay buffer IC with eight low-skew CMOS clock outputs in a 16-SOIC package. It uses a low-phase-noise PLL-based architecture to distribute one clock input across eight outputs while maintaining zero-delay operation. The device also supports PLL bypass and tri-state output operation. A zero-delay buffer is a clock-buffer IC that compensates propagation delay through its internal PLL so multiple destinations receive aligned clock edges. The MK2308S-1HILF belongs to the clock buffer and driver hierarchy, where clock management ICs support frequency synthesis, distribution, buffering, and low-skew fanout across digital, communications, industrial, and embedded systems. The principal operating characteristics are a 3.3 V supply, a maximum clock frequency of 133 MHz, eight outputs, and a 1:8 input-to-output fanout ratio. Outputs may be generated through the PLL for zero-delay operation or routed directly from the input for testing. CMOS outputs and low-skew behavior make the device appropriate for systems requiring predictable clock propagation among multiple loads. The PLL-based architecture is the core technical feature of the MK2308S-1HILF. It provides eight low-skew outputs at speeds up to 133 MHz, while bypass mode allows a clock to pass directly from the input to the outputs. The external-component requirements remain modest: the manufacturer datasheet specifies 0.01 mF decoupling capacitors at the two VDD and GND supply-pin pairs and notes that a 33 ohm series termination resistor may be used on each clock output to reduce reflections. Typical uses include fanout to processors, FPGAs, memory controllers, communications transceivers, and other clock-domain-crossing or multi-load systems. Eight outputs reduce the number of separate clock fanout stages required, while the low-skew characteristic helps preserve timing relationships between parallel interfaces and sequential logic. PCB implementation requires careful treatment of clock traces. Place the supply bypass capacitors adjacent to the specified pins, use short clock routes, maintain a continuous return path, and consider source termination when trace length, impedance discontinuities, or capacitive loading could produce reflections. Validate output timing and power integrity on the final board because package, connector, and interposer parasitics are not represented by the nominal frequency specification alone. This page combines the device architecture, operating limits, application guidance, pin-package information, and engineering trade-offs in one reference. It also distinguishes the directly supported ordering options from merely similar clock-buffer products, helping designers assess fit without treating unrelated package or feature sets as drop-in replacements.
MK2308S-1HITR - 133MHz Zero Delay Buffer | Renesas | Clock IC (Tape & Reel)
Renesas Electronics MK2308S-1HITR is a PLL-based zero-delay buffer IC operating up to 133 MHz, with eight low-skew outputs and CMOS-compatible interfaces in a 16-pin SOIC package measuring 0.154 inches, or 3.90 mm, in width. Its verified supply-voltage range is 3 V to 3.6 V, and its specified industrial operating-temperature range is -40°C to 85°C. The device belongs to the clock-generator, PLL, frequency-synthesizer, and clock-buffer hierarchy within clock and timing ICs. A zero-delay buffer is a clock-distribution circuit that reproduces an input clock at multiple outputs while compensating for propagation delay through an internal phase-locked loop. It is used where a system must fan one clock source across several loads without introducing excessive output-to-output skew. The MK2308S-1HITR can produce outputs from its PLL for zero-delay operation or directly from the input for testing. Its outputs can also be placed in tri-state or stopped-clock conditions, providing control functions useful in multi-domain clock trees. Key verified features include a maximum operating frequency of 133 MHz, eight outputs, one circuit, a PLL with bypass capability, and output skew of 200 ps. The CMOS bus interface supports integration with digital logic operating from the same 3.0 V to 3.6 V supply. The 16-SOIC surface-mount package provides a practical option for established through-hole-compatible board layouts and factory assembly processes. Technically, the device uses proprietary low-jitter PLL techniques to generate eight low-skew clock outputs. The PLL-based architecture is significant because it compensates for internal buffer propagation delay while distributing the clock. Direct-input bypass provides a diagnostic path for evaluating signal behavior without relying on the PLL-generated output mode. Output tri-state and stop-clock controls allow unused clock branches to be disabled or held according to system requirements. Typical applications include networking equipment, computing systems, telecommunications infrastructure, server clock trees, industrial control electronics, and communication modules. Its eight-output organization suits designs that must feed multiple clock domains, while the 133 MHz ceiling covers common legacy and industrial digital clocking requirements. The 3.3 V supply range also makes it suitable for systems whose logic rails are centered around 3.3 V. When laying out a circuit using the MK2308S-1HITR, preserve short and symmetrical clock paths from the device to each destination and follow the manufacturer's decoupling and layout recommendations. Validate output timing at the receiver, especially when fanout, trace length, or capacitive loading changes. Because the verified data does not provide the complete pinout, output-enable truth table, or absolute timing limits, those details should be confirmed against the manufacturer datasheet before release. This page consolidates the verified Renesas and distributor information for the MK2308S-1HITR, adds application-specific engineering context, identifies the available same-package comparison, and clearly separates confirmed specifications from parameters that still require datasheet verification.
MK2308S-1HLF - 133MHz 8-Output Zero Delay Buffer | Renesas
Renesas Electronics MK2308S-1HLF is a 3.3 V, eight-output, low-skew zero-delay buffer based on a phase-locked loop and operating up to 133 MHz. It provides CMOS outputs, 200 ps skew, and a 16-pin SOIC package. The device can generate outputs from its PLL for zero-delay operation or pass the input clock directly for testing. A zero-delay buffer is a clock-and-timing IC that regenerates a clock signal while using a phase-locked loop to minimize propagation delay between input and output. Its hierarchy is zero-delay buffer, clock buffer, clock driver, clock and timing IC, and integrated circuit. This topology helps distribute a high-speed source clock to multiple loads while controlling skew and jitter. The principal features of the MK2308S-1HLF include eight outputs, a maximum operating frequency of 133 MHz, 200 ps output skew, a 3 V to 3.6 V supply range, and CMOS interfacing. Each output can support tri-state operation, while the PLL-based architecture allows direct-input testing for circuit development and clock-tree analysis. Technically, the MK2308S-1HLF separates clock generation from distribution by using low-jitter PLL techniques. The eight outputs are intended to provide closely aligned copies of a common clock source. In zero-delay mode, the PLL compensates for internal propagation paths; in direct mode, the source clock can be routed without the PLL to help evaluate source behavior or board-level timing. Typical applications include processor and FPGA clock distribution, memory-controller fanout, networking-interface clock trees, test-and-measurement systems, and communications equipment operating at 3.3 V. It is particularly useful when several sequential circuits require related clock outputs and low output-to-output skew is more important than minimizing power consumption. Design the input and output clock paths for controlled impedance, maintain short and symmetric routing, and use the manufacturer pin-description table when assigning board connections. Decoupling, grounding, and unused-output handling should follow the manufacturer datasheet, especially when outputs are left unconnected or driven in tri-state mode. This page combines the MK2308S-1HLF operating specifications, pin-compatible family options, application guidance, and practical clock-tree design notes. It is structured to help engineers compare functionality, verify the 133 MHz and 200 ps timing targets, and assess where an eight-output 3.3 V zero-delay buffer fits within a larger clock-and-timing architecture.
MK2308S-1HTR - 133MHz 8-Output Zero-Delay Buffer | Renesas (Tape & Reel)
The Renesas Electronics MK2308S-1HTR is a PLL-based, eight-output CMOS zero-delay buffer rated to 133 MHz in a 16-SOIC surface-mount package. It operates from a 3.0 V to 3.6 V supply and provides eight low-skew outputs that can be sourced either through the PLL for zero-delay operation or directly from the input for testing. The verified device family information identifies 200 ps output skew and describes the part as a low-phase-noise, high-speed clock distribution device. A zero-delay buffer is a clock and timing IC that regenerates a reference clock through a phase-locked loop, compensating for clock-distribution delay while preserving frequency. In the hierarchy of electronic components, this device belongs to clock and timing integrated circuits, then PLL-based clock drivers, frequency-distribution circuits, and finally broader digital and power-management systems. It is used where multiple logic domains need closely related clock signals. Key verified features include a maximum clock frequency of 133 MHz, eight low-skew outputs, CMOS-compatible signaling, 3.0 V to 3.6 V operation, and selectable tri-state or stop-at-a-low output behavior. The PLL can be bypassed for testing or direct clock propagation. The available operating-temperature information identifies a 0°C to 70°C range, making the device suitable for commercial-temperature clock-distribution equipment. The low-skew output architecture helps maintain timing relationships across multiple destinations, which is important in networking, telecommunications, and computing systems. Its 3.3 V supply operation is compatible with systems designed around modern CMOS clock domains, while the SOIC package supports conventional surface-mount assembly and inspection. Typical uses include clock fan-out for communications equipment, synchronized digital logic, computing interfaces, test and measurement systems, and embedded control platforms. Designers should account for trace-length matching, output-enable control, bypass testing, and the required decoupling capacitors. The verified datasheet search result specifically calls for 0.01 uF capacitors near the device power pins. This page combines verified distributor and manufacturer information, cross-reference results, application guidance, and design considerations into an engineering-focused component record. It is intended to support purchasing decisions while clearly separating verified values from parameters requiring further datasheet confirmation.
MK2308S-2 - 133.3MHz Zero-Delay PLL Buffer | Renesas
The Renesas Electronics MK2308S-2 is a zero-delay PLL clock buffer operating up to 133.3 MHz, with one clock circuit and PLL bypass support in a 16-SOIC package measuring 0.154 inch, or 3.90 mm, wide. The device is intended for clock distribution and phase-alignment uses where outputs must support PLL operation or direct input-clock bypass. A zero-delay buffer is a clock and timing IC that uses a phase-locked loop to compensate propagation delay between an input clock and its outputs. In the broader hierarchy, this device belongs to clock generators, PLL-based frequency synthesizers, clock buffers, and timing ICs. Its CMOS output and bypass mode make it useful where clock distribution, testing, or phase alignment is required. The verified listing identifies the device as a zero-delay buffer with a maximum frequency of 133.3 MHz, one circuit, a 16-SOIC package, PLL operation with bypass, and clock input. The package is a surface-mount SOIC format with a stated width of 3.90 mm. These details identify the MK2308S-2 as a timing-integrity component rather than a general-purpose logic gate or power-management device. Because the supplied source material does not include a complete manufacturer electrical table, details such as supply voltage, output count, skew, jitter, propagation delay, temperature range, and exact pin names remain marked as data needed. Designers should consult the manufacturer datasheet and verify the pinout, voltage requirements, and timing limits before layout or production use. Typical uses include processor and FPGA clock distribution, communication-system clock conditioning, test-and-measurement clock networks, and general digital systems requiring low-skew clock fan-out. The supplied cross-reference data identifies MK2308S-2LF as a pin-compatible replacement candidate, while a comparison result also names CY2308SC-2T for evaluation. Both require package, timing, and application-specific verification rather than automatic substitution. For implementation, preserve short, controlled-impedance clock traces, provide the required bypass and decoupling capacitors, and keep the PLL input and outputs away from noisy high-current switching paths. Confirm whether bypass mode is required during startup or test before finalizing the system clock architecture. This page consolidates the verified distributor and datasheet-index information, replacement candidates, and practical design guidance to support component selection and PCB planning for the Renesas Electronics MK2308S-2.
MK2308S-2I - 133.3MHz Zero-Delay Buffer | Renesas
The Renesas Electronics MK2308S-2I is a 133.3 MHz PLL-based zero-delay buffer with one clock input, eight CMOS outputs, and a 16-SOIC surface-mount package. It operates from 3 V to 5.5 V and provides four divided outputs at one-half the input frequency, according to the available product and datasheet records. A zero-delay buffer is a clock and timing semiconductor that uses a phase-locked loop to reproduce a clock while compensating for propagation delay introduced by the buffer. In the broader hierarchy, it belongs to clock and timing ICs, frequency-control ICs, and PLL-based clock circuits. Its purpose is to supply multiple closely related clock outputs to high-speed digital systems. The available records identify the MK2308-2 family as a low-jitter, low-skew, PLL-based device intended for high-speed applications. The family description states that its eight outputs operate at speeds up to 133.3 MHz at 3.3 V. Four outputs are specified at one-half the input frequency, while the remaining outputs support zero-delay operation or direct clock bypass. The package is identified as a 16-SOIC measuring 3.90 mm wide. Because the target suffix denotes a specific ordering configuration, engineers should verify temperature grade, tube packaging, and production lifecycle status against current Renesas documentation before committing a new design. The verified web results establish the core function and several headline specifications, but they do not provide a complete parameter table, guaranteed timing limits, or an official manufacturer URL for this exact suffix. Typical uses include processor clock distribution, communications equipment, storage controllers, test systems, and other circuits requiring several outputs derived from one clock source. The divided bank can support lower-frequency peripherals while the undivided outputs serve the main digital domain. Independent output control may support testing and bus management, subject to the functions and limits stated in the datasheet. The principal design task is to verify clock-edge integrity at the intended voltage and frequency. Board traces should be short and return-current paths continuous, while PLL input and bypass connections must follow the manufacturer layout guidance. Probe or capacitance added by test equipment can alter edge rate and skew, so timing validation should include realistic loading. This page consolidates distributor availability, the Renesas MK2308-2 family description, package information, and replacement research. It also separates verified facts from missing production data so procurement and design teams can assess the MK2308S-2I without mistaking search snippets for a complete datasheet specification.
MK2308S-2ILF - 3.3V Zero-Delay Clock Buffer | Renesas
Renesas Electronics MK2308S-2ILF is a 3.3 V zero-delay, low-skew clock buffer integrated circuit packaged in a 16-pin SOIC. The device is intended for clock distribution applications where multiple sequential logic circuits require closely related clock signals. Its defining functions are zero-delay buffering and low-skew output generation, which help preserve clock-edge alignment across distributed digital systems. A zero-delay buffer is a timing integrated circuit that accepts an incoming clock and reproduces it at its outputs with very low nominal propagation delay. It belongs to the clock and timing IC hierarchy, alongside clock generators, phase-locked loops, frequency synthesizers, clock dividers, and clock-tree components. Such buffers are commonly positioned after an oscillator or clock controller to fan out a high-quality reference clock without relying on a remote source to drive several loads directly. The MK2308S-2ILF family is identified as a 3.3 V, low-skew clock-buffer solution. A related 16-SOIC listing for the MK2308S-2I identifies the device as a zero-delay buffer operating to 133.3 MHz. These descriptions place the part in applications requiring orderly clock propagation through processors, programmable logic, communications equipment, and other synchronous digital systems. The SOIC-16 package supports conventional surface-mount PCB assembly while exposing the complete buffer interface. Clock buffers can reduce loading problems that arise when a source clock is connected to multiple destinations. By placing the buffer near the receiving circuitry, designers can isolate the source from board capacitance, interconnect loading, and receiver input thresholds. Low-skew operation is valuable when several destinations must act within a defined timing window. The buffer does not generate a new reference frequency; instead, it preserves and redistributes the input clock with controlled edge relationships. Typical application areas include processor and microcontroller clock trees, FPGA or CPLL input distribution, communications-interface clock fanout, data-acquisition systems, and compact industrial control electronics. The device is especially relevant where multiple downstream circuits share one oscillator output but require local buffering for predictable timing and signal integrity. When laying out a design, place the buffer close to the clock receivers, keep clock traces short and impedance-controlled, and minimize stub lengths. Confirm input and output logic levels, operating frequency, load capacitance, and enable or power-control requirements against the manufacturer datasheet before releasing the PCB. Adequate grounding and a clean supply reference are important because clock-edge timing quality can be affected by return-path discontinuities and supply noise. This product page combines the manufacturer-device identity, exact MPN, package information, clock-buffer function, application context, replacement considerations, and PCB-oriented design guidance. It is intended to help engineers identify the correct Renesas clock-buffer ordering code and evaluate board-level integration without obscuring the distinction between confirmed device facts and parameters that still require datasheet confirmation.
MK2308S-2ILFT - 133.3MHz 8-Output Zero-Delay Buffer | Renesas
Renesas Electronics MK2308S-2ILFT is a PLL-based, low-jitter, low-skew zero-delay clock buffer operating up to 133.3 MHz at 3.3 V, with eight CMOS outputs in a 16-pin SOIC package. The device provides four 1X outputs and four 1/2X outputs, allowing simultaneous propagation and divided clock distribution from one source. A zero-delay buffer is a clock-integrity device that uses a phase-locked loop to reproduce and distribute a clock while compensating for internal propagation delay. In system terms, it belongs to the clock buffer and driver class within clock and timing integrated circuits, where multiple low-skew copies of a high-speed clock are required for processors, memory interfaces, communication links, and test equipment. The MK2308S-2ILFT combines clock generation, frequency division, and output buffering in one integrated circuit. Key features include operation from a 3 V to 3.6 V supply, a maximum operating frequency of 133.3 MHz, and output-to-output skew below 250 ps in zero-delay mode. Its eight outputs are organized as four 1X channels and four 1/2X channels. The PLL-based architecture aligns the rising edge of the input clock with the rising edges of the outputs, helping minimize accumulated timing displacement between destinations. The low phase-noise and low-jitter characteristics are important in systems that transfer synchronous data at high clock rates. By producing several outputs from a common PLL reference, the device reduces the cumulative skew that can develop when one clock source drives multiple loads through separate buffers. The CMOS interface also supports integration with 3.3 V digital logic, while the available test and bypass behavior aids board-level validation. Typical uses include CPU and DSP clock distribution, network-interface clock fanout, memory-controller clock distribution, communications equipment, and industrial control systems. The four divided outputs are particularly useful when a subsystem requires a reference at half the fundamental clock frequency. The same package also supports compact implementations where multiple clock domains must originate from one low-frequency reference. Designers should preserve a continuous supply path and route clock outputs according to the package guidance in the manufacturer datasheet. PCB return paths, ground-plane continuity, and matched trace characteristics help control edge degradation and coupling. The datasheet must be consulted for the exact pin assignment, output-disable truth table, bypass configuration, and recommended external component values before layout is released. This page combines the verified device characteristics, a practical application guide, pin and documentation guidance, and a disciplined comparison framework. It also distinguishes true same-footprint alternatives from functional clock-buffer options that would require different routing or a redesigned land pattern.
MK2308S-2LF - 133.3MHz Zero-Delay Buffer | Renesas
Renesas Electronics MK2308S-2LF is a PLL-based zero-delay buffer clock driver operating up to 133.3 MHz with eight low-skew outputs and a 3 V to 3.6 V CMOS supply range. The device is supplied in a 16-pin SOIC package measuring approximately 3.90 mm wide, making it suitable for compact systems requiring multiple low-skew clock copies. A zero-delay buffer is a clock and timing integrated circuit that regenerates a clock through a phase-locked loop while seeking near-zero propagation delay. Within the clock and timing IC hierarchy, the MK2308S-2LF combines a PLL-based timing engine, low-skew output distribution, and CMOS interfacing. It is used where several receiving circuits need a common clock reference with tightly controlled output-to-output timing. Key features include a maximum operating frequency of 133.3 MHz, eight outputs, a 3 V to 3.6 V supply voltage range, and 200 ps skew as identified in the indexed datasheet information. The architecture also includes four half-frequency outputs, allowing clock generation or division within the same package. A CMOS bus interface supports integration with contemporary digital logic operating at 3.3 V. Technically, the device uses proprietary low-jitter PLL techniques to distribute the input clock. In zero-delay mode, the rising input edge is mapped to output edges with near-zero delay, while the half-rate output bank provides divided clock signals. The 16-SOIC arrangement exposes the input, power, ground, and clock outputs, but exact individual pin names and the complete pin numbering map are not included in the provided source excerpts. Typical uses include processor and FPGA clock distribution, memory clock fanout, communications equipment, industrial control systems, and general-purpose digital logic. Eight outputs reduce the need for multiple clock-buffer packages when a design requires several synchronized destinations, while the low-skew specification supports deterministic data transfer between clocked circuits. Designers should verify output loading, trace length matching, supply decoupling, and the complete pin configuration against the manufacturer datasheet before layout. Because this part uses a PLL-based architecture, power-supply quality and clock-input stability can affect output jitter even when the advertised skew is low. This product record combines the verified distributor specifications, manufacturer-linked datasheet references, ordering information, and same-footprint alternatives. It also adds application guidance, comparison parameters, and practical integration notes that are not consolidated in the individual distributor listings.
MK2308S-2LFTR - 133.3MHz Zero-Delay Buffer | Renesas (Tape & Reel)
Renesas Electronics MK2308S-2LFTR is a PLL-based zero-delay buffer clock driver operating up to 133.3 MHz with eight low-skew outputs and a 3 V to 3.6 V CMOS supply range. The device is supplied in a 16-pin SOIC package measuring approximately 3.90 mm wide, making it suitable for compact systems requiring multiple low-skew clock copies. A zero-delay buffer is a clock and timing integrated circuit that regenerates a clock through a phase-locked loop while seeking near-zero propagation delay. Within the clock and timing IC hierarchy, the MK2308S-2LFTR combines a PLL-based timing engine, low-skew output distribution, and CMOS interfacing. It is used where several receiving circuits need a common clock reference with tightly controlled output-to-output timing. Key features include a maximum operating frequency of 133.3 MHz, eight outputs, a 3 V to 3.6 V supply voltage range, and 200 ps skew as identified in the indexed datasheet information. The architecture also includes four half-frequency outputs, allowing clock generation or division within the same package. A CMOS bus interface supports integration with contemporary digital logic operating at 3.3 V. Technically, the device uses proprietary low-jitter PLL techniques to distribute the input clock. In zero-delay mode, the rising input edge is mapped to output edges with near-zero delay, while the half-rate output bank provides divided clock signals. The 16-SOIC arrangement exposes the input, power, ground, and clock outputs, but exact individual pin names and the complete pin numbering map are not included in the provided source excerpts. Typical uses include processor and FPGA clock distribution, memory clock fanout, communications equipment, industrial control systems, and general-purpose digital logic. Eight outputs reduce the need for multiple clock-buffer packages when a design requires several synchronized destinations, while the low-skew specification supports deterministic data transfer between clocked circuits. Designers should verify output loading, trace length matching, supply decoupling, and the complete pin configuration against the manufacturer datasheet before layout. Because this part uses a PLL-based architecture, power-supply quality and clock-input stability can affect output jitter even when the advertised skew is low. This product record combines the verified distributor specifications, manufacturer-linked datasheet references, ordering information, and same-footprint alternatives. It also adds application guidance, comparison parameters, and practical integration notes that are not consolidated in the individual distributor listings.
MK2308S-2TR - 133.3MHz Zero-Delay PLL Buffer | Renesas (Tape & Reel)
The Renesas Electronics MK2308S-2TR is a zero-delay PLL clock buffer operating up to 133.3 MHz, with one clock circuit and PLL bypass support in a 16-SOIC package measuring 0.154 inch, or 3.90 mm, wide. The device is intended for clock distribution and phase-alignment uses where outputs must support PLL operation or direct input-clock bypass. A zero-delay buffer is a clock and timing IC that uses a phase-locked loop to compensate propagation delay between an input clock and its outputs. In the broader hierarchy, this device belongs to clock generators, PLL-based frequency synthesizers, clock buffers, and timing ICs. Its CMOS output and bypass mode make it useful where clock distribution, testing, or phase alignment is required. The verified listing identifies the device as a zero-delay buffer with a maximum frequency of 133.3 MHz, one circuit, a 16-SOIC package, PLL operation with bypass, and clock input. The package is a surface-mount SOIC format with a stated width of 3.90 mm. These details identify the MK2308S-2TR as a timing-integrity component rather than a general-purpose logic gate or power-management device. Because the supplied source material does not include a complete manufacturer electrical table, details such as supply voltage, output count, skew, jitter, propagation delay, temperature range, and exact pin names remain marked as data needed. Designers should consult the manufacturer datasheet and verify the pinout, voltage requirements, and timing limits before layout or production use. Typical uses include processor and FPGA clock distribution, communication-system clock conditioning, test-and-measurement clock networks, and general digital systems requiring low-skew clock fan-out. The supplied cross-reference data identifies MK2308S-2TRLF as a pin-compatible replacement candidate, while a comparison result also names CY2308SC-2T for evaluation. Both require package, timing, and application-specific verification rather than automatic substitution. For implementation, preserve short, controlled-impedance clock traces, provide the required bypass and decoupling capacitors, and keep the PLL input and outputs away from noisy high-current switching paths. Confirm whether bypass mode is required during startup or test before finalizing the system clock architecture. This page consolidates the verified distributor and datasheet-index information, replacement candidates, and practical design guidance to support component selection and PCB planning for the Renesas Electronics MK2308S-2TR.
MK2703BSILF - 27MHz PLL Audio Clock Synthesizer IC | Renesas
The Renesas Electronics MK2703BSILF is a PLL audio clock synthesizer integrated circuit that delivers a CMOS clock output up to 27 MHz from a crystal or external clock reference, in an 8-pin SOIC (PDSO8, 0.154 in / 3.90 mm wide) surface-mount package. The device contains an internal phase-locked loop with no bypass path and no divider or multiplier stage, and it ships in tube packaging as a RoHS-compliant, surface-mount clock and timing IC. A PLL clock synthesizer is a clock and timing integrated circuit that locks an internal voltage-controlled oscillator to a stable external reference, normally a crystal resonator, and multiplies that reference into a higher, jitter-cleaned frequency. In the device hierarchy it sits above a plain crystal oscillator and above a divider-only clock buffer, but below a general-purpose fractional-N PLL clock generator with programmable multipliers and dividers. That middle position is exactly why the MK2703BSILF suits audio subsystems: it delivers a multiplied, low-jitter clock without the programming overhead of a fractional-N device. Key specifications of the MK2703BSILF include a 27 MHz maximum output frequency, CMOS output type, an input that accepts either a crystal or a clock, an internal PLL, and a package body of only 8 pins. Because the loop offers no bypass option and no user-selectable divider or multiplier, the design is fixed-function, which reduces external component count and removes firmware or register configuration from the clocking path. The part is RoHS compliant and supplied in tube packing for prototype and low-volume assembly. Architecturally, the MK2703BSILF belongs to the legacy IDT/Renesas PLL audio clock synthesizer family documented under the MK2703B datasheet. The PLL multiplies a high-stability reference, and the multiplied clock is presented on CMOS-compatible output drivers intended for driving audio codec and DAC clock inputs directly. Because the loop uses a fixed multiplication ratio, phase noise and jitter are characterised for a single operating point rather than a programmable set, so supply decoupling and reference layout quality dominate achievable jitter in a finished design. Typical uses include audio codec master-clock generation, digital-to-analog converter clocking in CD and DVD receivers, consumer audio hubs, and multimedia processor subsystems that need a multiplied CMOS clock from a single crystal source. The 8-pin SOIC footprint is also convenient for legacy audio board revisions where a small, low-cost, fixed-function clock generator is preferred over a configurable jitter cleaner with serial programming. When designing around this part, plan the reference network carefully: keep the crystal or oscillator close to the input pins, provide solid ground-plane return for output return paths, and bypass the supply pins locally with ceramic capacitance. Because this is an obsolete, fixed-function device, verify pin compatibility and supply sequencing against any replacement before committing to a new design revision. This page consolidates manufacturer datasheet details, distributor availability, drop-in replacement candidates and practical design guidance for the MK2703BSILF in one place, saving the cross-checking normally spread across datasheet, lifecycle and cross-reference lookups.
MK2703BSLF - 27MHz PLL Clock Synthesizer | Renesas
Renesas MK2703BSLF is a low-cost, low-jitter PLL clock synthesizer IC with a 27 MHz crystal or clock input, a CMOS bus interface, a 3.13 V to 5.5 V supply range, and an 8-pin SOIC package. It is designed to produce a buffered reference clock and a selectable audio clock for set-top box and multimedia systems. A PLL clock synthesizer is a clock and timing integrated circuit that uses phase-locked-loop technology to generate one or more stable timing signals from an external crystal or clock source. Within the semiconductor hierarchy, it belongs to the PLL and frequency-synthesizer family, combining an oscillator reference with feedback and control circuitry. The MK2703BSLF can therefore consolidate oscillator and PLL functions that might otherwise be implemented separately. The device offers a 27 MHz reference input, selectable audio-clock generation, buffered clock outputs, CMOS compatibility, and a surface-mount SOIC-8 package. Its low-cost positioning and low-jitter PLL architecture are significant for consumer multimedia equipment, where a stable reference can be distributed to audio-processing, decoding, control, and communications blocks without implementing a complete timing subsystem on the motherboard. According to the Renesas MK2703B datasheet, the device uses patented analog PLL techniques with a 27 MHz crystal or clock input. The resulting buffered reference clock and selectable audio clock are intended to simplify clock distribution in set-top boxes and multimedia systems. The manufacturer identifies MK2703BSLF as a RoHS-compliant SOIC-8 device, although detailed operating-temperature, output-jitter, output-frequency, and load-capacitance limits are not included in the supplied search data. Typical uses include set-top box main boards, multimedia appliance clock trees, audio codec clocking, digital media decoders, and compact consumer equipment requiring a dedicated reference and audio-clock source. Its SOIC-8 surface-mount package supports conventional reflow assembly and makes the device suitable for cost-sensitive mixed-signal and digital boards where a larger BGA or QFN clock generator would be unnecessary. Designers should verify the exact output frequencies, crystal load capacitance, startup time, jitter limits, decoupling requirements, and output-drive configuration against the current Renesas datasheet before release. PCB layout should keep the oscillator loop compact, provide a clean supply and ground connection, and avoid routing clock outputs through long, parallel-coupled traces where unnecessary. This product page consolidates manufacturer information, distributor pricing, verified compliance details, replacement evidence, and practical engineering guidance. It distinguishes verified facts from parameters still requiring confirmation, helping engineers source MK2703BSLF and evaluate drop-in alternatives without relying on unsupported assumptions.
MK2703BSLFTR - 27MHz PLL Clock Synthesizer | Renesas (Tape & Reel)
Renesas MK2703BSLFTR is a low-cost, low-jitter PLL clock synthesizer IC with a 27 MHz crystal or clock input, a CMOS bus interface, a 3.13 V to 5.5 V supply range, and an 8-pin SOIC package. It is designed to produce a buffered reference clock and a selectable audio clock for set-top box and multimedia systems. A PLL clock synthesizer is a clock and timing integrated circuit that uses phase-locked-loop technology to generate one or more stable timing signals from an external crystal or clock source. Within the semiconductor hierarchy, it belongs to the PLL and frequency-synthesizer family, combining an oscillator reference with feedback and control circuitry. The MK2703BSLFTR can therefore consolidate oscillator and PLL functions that might otherwise be implemented separately. The device offers a 27 MHz reference input, selectable audio-clock generation, buffered clock outputs, CMOS compatibility, and a surface-mount SOIC-8 package. Its low-cost positioning and low-jitter PLL architecture are significant for consumer multimedia equipment, where a stable reference can be distributed to audio-processing, decoding, control, and communications blocks without implementing a complete timing subsystem on the motherboard. According to the Renesas MK2703B datasheet, the device uses patented analog PLL techniques with a 27 MHz crystal or clock input. The resulting buffered reference clock and selectable audio clock are intended to simplify clock distribution in set-top boxes and multimedia systems. The manufacturer identifies MK2703BSLFTR as a RoHS-compliant SOIC-8 device, although detailed operating-temperature, output-jitter, output-frequency, and load-capacitance limits are not included in the supplied search data. Typical uses include set-top box main boards, multimedia appliance clock trees, audio codec clocking, digital media decoders, and compact consumer equipment requiring a dedicated reference and audio-clock source. Its SOIC-8 surface-mount package supports conventional reflow assembly and makes the device suitable for cost-sensitive mixed-signal and digital boards where a larger BGA or QFN clock generator would be unnecessary. Designers should verify the exact output frequencies, crystal load capacitance, startup time, jitter limits, decoupling requirements, and output-drive configuration against the current Renesas datasheet before release. PCB layout should keep the oscillator loop compact, provide a clean supply and ground connection, and avoid routing clock outputs through long, parallel-coupled traces where unnecessary. This product page consolidates manufacturer information, distributor pricing, verified compliance details, replacement evidence, and practical engineering guidance. It distinguishes verified facts from parameters still requiring confirmation, helping engineers source MK2703BSLFTR and evaluate drop-in alternatives without relying on unsupported assumptions.
MK2703S - 27MHz PLL Clock Synthesizer | Renesas
The Renesas Electronics MK2703S is a 27MHz PLL clock synthesizer IC designed for low-cost, low-jitter clock generation in set-top box and multimedia systems, supplied in an 8-pin SOIC surface-mount package. It operates from 3.13V to 5.5V and is identified by distributor listings as a PLL clock synthesizer with one clock output. A PLL clock synthesizer is a timing IC that uses a phase-locked loop to generate or distribute a stable reference clock for digital and multimedia systems. In the broader electronics hierarchy, the MK2703S belongs to clock and timing integrated circuits, alongside clock generators, frequency dividers, PLL multipliers, and clock buffers. Its purpose is to replace discrete oscillator and PLL circuitry with a compact integrated solution. The verified product data identifies the MK2703S as a low-cost, low-jitter, high-performance PLL clock synthesizer for set-top boxes and multimedia equipment. Its specified 27MHz operating frequency provides a centralized timing reference for system logic, while the 3.13V to 5.5V supply range accommodates common embedded and consumer electronics rails. The 8-SOIC package supports conventional surface-mount assembly and reduces board area compared with discrete oscillator networks. The part is offered in tube packaging according to the verified distributor listing, and distributor records also identify it as a PLL clock synthesizer IC with a 1-output configuration. Exact jitter, phase noise, lock-time, output-drive, and reference-input details were not included in the supplied web excerpts and therefore require confirmation from the manufacturer datasheet before production release. Those unspecified values are important when evaluating a replacement or a new board design. Typical uses include set-top box timing, multimedia processor clocks, digital media modules, and compact consumer systems requiring a single synthesized clock. The MK2703S can replace a discrete oscillator and PLL implementation, but the reference clock source, loop-filter network, output load, and decoupling requirements must follow the manufacturer application guidance. The verified source describes the device as intended to replace oscillators and PLL circuits, while the operating conditions and package details define the core procurement and integration constraints. For a new design, begin with the official Renesas MK27033 datasheet and verify the complete pinout, recommended reference configuration, and electrical limits before layout. Distributor search data confirms the 27MHz device, SOIC-8 package, and supply range, but it does not provide enough detail to reconstruct the full application circuit. Pricing, stock, and lifecycle status should also be checked against current distributor records at the time of purchase. This product summary combines verified distributor attributes with the manufacturer datasheet resource, while clearly separating known electrical facts from parameters requiring datasheet confirmation. It is useful for initial sourcing, clock-tree architecture review, and identifying whether the MK2703S belongs in a candidate design, but it is not a substitute for the complete manufacturer datasheet.
MK2703SI - Low-Jitter PLL Audio Clock Synthesizer | Renesas
The Renesas Electronics MK2703SI is a low-cost, low-jitter PLL audio clock synthesizer designed to replace discrete oscillator and PLL circuits in set-top box and multimedia systems. The verified source material identifies it as an 8-SOIC device with a 0.154 inch, 3.90 mm package width. The available data does not provide a verified output-frequency list, input-frequency range, supply voltage, current consumption, pin mapping, or exact operating-temperature values, so those parameters remain design-review items. A PLL audio clock synthesizer is a clock-and-timing IC that uses a phase-locked loop to generate or distribute one or more timing signals with controlled frequency relationships. In the broader electronics hierarchy, it belongs to clock generation, frequency synthesis, PLL, timing IC, and digital signal-support categories. This makes the MK2703SI relevant where audio, multimedia, or embedded systems need a stable reference or derived clock instead of a collection of separate oscillators and divider logic. The manufacturer search results identify the MK2703 family as a PLL audio clock synthesizer and specifically describe the device as a low-cost, low-jitter, high-performance alternative to oscillator and PLL circuits. The SI ordering suffix is associated with an 8-SOIC package in the verified distributor result. Because the supplied web data does not expose the complete electrical specification table, designers should verify frequency generation modes, reference requirements, output drive, supply limits, decoupling, and signal integrity against the official Renesas MK2703 datasheet before layout release. The MK2703SI can be considered for set-top box clocking, multimedia-system timing, audio-clock generation, decoder reference clocks, and embedded multimedia platforms. In a typical implementation, the device would receive a reference signal and produce one or more derived clocks required by downstream processors, converters, or audio circuitry. The main design trade-offs are package footprint, supported output frequencies, jitter, reference quality, supply noise, and whether the required clock architecture matches the device's verified control interface. Use the official MK2703 datasheet as the controlling source for pin names, timing diagrams, electrical limits, recommended crystals or oscillators, and application examples. Do not infer a pinout from the 8-SOIC package alone. In particular, verify every unused or no-connect pin, the exposed thermal requirements, the required supply bypass capacitors, and the maximum operating frequency before substituting the part into an existing design. This page consolidates the verified distributor identity, package information, family description, datasheet links, sourcing context, and engineering caveats for MK2703SI. It also distinguishes confirmed facts from parameters that still require datasheet verification, helping engineers identify the correct next step without presenting unverified clock or electrical values as specifications.
MK2703SILF - 27MHz PLL Audio Clock Synthesizer | Renesas
The Renesas Electronics MK2703SILF is a PLL audio clock synthesizer operating from a 27 MHz crystal or clock input, with a supply range of 3.13 V to 5.5 V, in an 8-pin SOIC package measuring 3.90 mm wide. Designed to replace discrete oscillators and PLL circuits, it generates a buffered reference clock and a selectable audio clock for set-top box and multimedia systems. A PLL clock synthesizer is a clock-and-timing IC that multiplies or divides a stable input reference to produce one or more synchronized output frequencies. In the broader semiconductor hierarchy, the MK2703 belongs to the PLL multiplier/divider family, the clock generator and synthesizer class, and ultimately the clock-and-timing integrated-circuit category. Its low-cost integration reduces component count and simplifies clock-tree construction compared with separate crystal oscillators, dividers, and phase-locked-loop circuitry. The verified product information identifies the MK2703SILF as a 27 MHz single PLL clock synthesizer with an 8-pin SOIC surface-mount package. It accepts a 3.13 V to 5.5 V operating supply and provides a buffered reference output together with a selectable audio clock. These functions are useful when downstream converters, codecs, interface circuits, or digital signal processors require a derived clock that remains phase-related to the system reference. Technically, the device uses analog phase-locked-loop techniques to lock an internally controlled output to the external 27 MHz reference. Locking the synthesized clock to the same reference used by the rest of the system can improve timing consistency, while the selectable output division allows a practical audio-clock rate to be produced without a separate programmable synthesizer. Because the supplied web data does not enumerate every programmable frequency, jitter value, output format, or loop filter setting, those details must be confirmed in the manufacturer datasheet before final clock-tree validation. Typical uses include set-top box clock trees, multimedia receivers, DVD and digital-audio equipment, network equipment requiring stable derived clocks, and embedded audio systems where a single reference must feed several clock domains. The device is also appropriate for industrial control equipment when its specified operating range, electrical limits, and environmental qualifications match the system requirements. When laying out an MK2703SILF design, place the device and its associated crystal or clock-source components close to the circuit being clocked, keep output routes short, and provide return paths that do not share high-current switching paths. Confirm crystal load capacitance, output series termination, supply bypassing, and all supported output frequencies from the manufacturer datasheet before production release. This product record combines verified distributor and manufacturer information, traceable source links, honest specification gaps, and engineering-oriented application guidance. It distinguishes documented facts from parameters that still require verification, helping engineers evaluate the MK2703SILF without treating incomplete distributor summaries as a complete electrical datasheet.
MK2703SILFTR - 27MHz PLL Audio Clock Synthesizer | Renesas (Tape & Reel)
The Renesas Electronics MK2703SILFTR is a PLL audio clock synthesizer operating from a 27 MHz crystal or clock input, with a supply range of 3.13 V to 5.5 V, in an 8-pin SOIC package measuring 3.90 mm wide. Designed to replace discrete oscillators and PLL circuits, it generates a buffered reference clock and a selectable audio clock for set-top box and multimedia systems. A PLL clock synthesizer is a clock-and-timing IC that multiplies or divides a stable input reference to produce one or more synchronized output frequencies. In the broader semiconductor hierarchy, the MK2703 belongs to the PLL multiplier/divider family, the clock generator and synthesizer class, and ultimately the clock-and-timing integrated-circuit category. Its low-cost integration reduces component count and simplifies clock-tree construction compared with separate crystal oscillators, dividers, and phase-locked-loop circuitry. The verified product information identifies the MK2703SILFTR as a 27 MHz single PLL clock synthesizer with an 8-pin SOIC surface-mount package. It accepts a 3.13 V to 5.5 V operating supply and provides a buffered reference output together with a selectable audio clock. These functions are useful when downstream converters, codecs, interface circuits, or digital signal processors require a derived clock that remains phase-related to the system reference. Technically, the device uses analog phase-locked-loop techniques to lock an internally controlled output to the external 27 MHz reference. Locking the synthesized clock to the same reference used by the rest of the system can improve timing consistency, while the selectable output division allows a practical audio-clock rate to be produced without a separate programmable synthesizer. Because the supplied web data does not enumerate every programmable frequency, jitter value, output format, or loop filter setting, those details must be confirmed in the manufacturer datasheet before final clock-tree validation. Typical uses include set-top box clock trees, multimedia receivers, DVD and digital-audio equipment, network equipment requiring stable derived clocks, and embedded audio systems where a single reference must feed several clock domains. The device is also appropriate for industrial control equipment when its specified operating range, electrical limits, and environmental qualifications match the system requirements. When laying out an MK2703SILFTR design, place the device and its associated crystal or clock-source components close to the circuit being clocked, keep output routes short, and provide return paths that do not share high-current switching paths. Confirm crystal load capacitance, output series termination, supply bypassing, and all supported output frequencies from the manufacturer datasheet before production release. This product record combines verified distributor and manufacturer information, traceable source links, honest specification gaps, and engineering-oriented application guidance. It distinguishes documented facts from parameters that still require verification, helping engineers evaluate the MK2703SILFTR without treating incomplete distributor summaries as a complete electrical datasheet.
MK2703SITR - Low-Jitter PLL Audio Clock Synthesizer | Renesas (Tape & Reel)
The Renesas Electronics MK2703SITR is a low-cost, low-jitter PLL audio clock synthesizer designed to replace discrete oscillator and PLL circuits in set-top box and multimedia systems. The verified source material identifies it as an 8-SOIC device with a 0.154 inch, 3.90 mm package width. The available data does not provide a verified output-frequency list, input-frequency range, supply voltage, current consumption, pin mapping, or exact operating-temperature values, so those parameters remain design-review items. A PLL audio clock synthesizer is a clock-and-timing IC that uses a phase-locked loop to generate or distribute one or more timing signals with controlled frequency relationships. In the broader electronics hierarchy, it belongs to clock generation, frequency synthesis, PLL, timing IC, and digital signal-support categories. This makes the MK2703SITR relevant where audio, multimedia, or embedded systems need a stable reference or derived clock instead of a collection of separate oscillators and divider logic. The manufacturer search results identify the MK2703 family as a PLL audio clock synthesizer and specifically describe the device as a low-cost, low-jitter, high-performance alternative to oscillator and PLL circuits. The SI ordering suffix is associated with an 8-SOIC package in the verified distributor result. Because the supplied web data does not expose the complete electrical specification table, designers should verify frequency generation modes, reference requirements, output drive, supply limits, decoupling, and signal integrity against the official Renesas MK2703 datasheet before layout release. The MK2703SITR can be considered for set-top box clocking, multimedia-system timing, audio-clock generation, decoder reference clocks, and embedded multimedia platforms. In a typical implementation, the device would receive a reference signal and produce one or more derived clocks required by downstream processors, converters, or audio circuitry. The main design trade-offs are package footprint, supported output frequencies, jitter, reference quality, supply noise, and whether the required clock architecture matches the device's verified control interface. Use the official MK2703 datasheet as the controlling source for pin names, timing diagrams, electrical limits, recommended crystals or oscillators, and application examples. Do not infer a pinout from the 8-SOIC package alone. In particular, verify every unused or no-connect pin, the exposed thermal requirements, the required supply bypass capacitors, and the maximum operating frequency before substituting the part into an existing design. This page consolidates the verified distributor identity, package information, family description, datasheet links, sourcing context, and engineering caveats for MK2703SITR. It also distinguishes confirmed facts from parameters that still require datasheet verification, helping engineers identify the correct next step without presenting unverified clock or electrical values as specifications.