Clock & Timing
بەرهەمەکان (970+)
ADF4216BRU - Dual Integer-N PLL Synthesizer 1.2 GHz | Analog Devices
The Analog Devices ADF4216BRU is a dual RF PLL frequency synthesizer delivering a 550 MHz to 1.2 GHz RF output with an integer-N phase-locked loop architecture, packaged in a 20-lead TSSOP. It combines a low-noise digital phase frequency detector (PFD), a precision charge pump, programmable reference and RF/IF dividers, and a 3-wire serial interface in a single RF/IF local oscillator (LO) solution. A PLL frequency synthesizer is a closed-loop timing device in which a voltage-controlled oscillator (VCO) output is phase- and frequency-locked to a stable reference source through a phase frequency detector and charge pump. It sits in the RF and IF signal chain of wireless transmitters and receivers, converting a single low-frequency reference into the high, spectrally pure local oscillator tones required for up-conversion and down-conversion. The hierarchy runs from phase-locked loop to frequency synthesizer to clock and timing IC to integrated circuit. The ADF4216 supports programmable reference, RF, and IF N-divider ratios, selectable charge pump currents, and selectable dual-modulus prescalers of 16/17 for the IF chain and 64/65 for the RF chain. Because the loop is integer-N, the synthesizer frequency is the reference frequency multiplied by an integer ratio, giving excellent phase noise and very low reference feedthrough at the cost of fractional-N flexibility. A dedicated power-down mode shuts the part down for leakage control between burst transmissions. Operated from a 3 V to 5.5 V supply, the device integrates everything a designer needs for a dual-LO transceiver front end: two independent synthesizer channels that can drive both the RF and IF sections of a wireless receiver or transmitter. The 3-wire serial interface allows the divider ratios, prescaler, charge pump, and counter settings to be loaded from a host microcontroller or baseband processor. Typical applications include GSM and CDMA wireless handsets, wireless local loop and base-station equipment, WCDMA and TD-SCDMA transceiver front ends, RFID readers, microwave and satellite up/down converters, and instrumentation. In each case the device replaces separate oscillators and dividers while tightening phase noise and reducing board area. When designing around the ADF4216, pay close attention to loop filter component selection, reference phase noise, and the charge pump setting. A mismatched charge pump current and bandwidth combination produces high reference spurs, while an aggressive loop bandwidth trades phase noise for lock time. Keep the reference and RF traces short and well decoupled, and follow the grounding and decoupling layout recommended in the manufacturer datasheet. This page combines verified distributor and manufacturer information with drop-in alternatives, a parameter-by-parameter comparison table, and practical design notes that go beyond the raw datasheet tables, helping engineers shortlist, source, and lay out the part with confidence.
ADF4216BRU-REEL - Dual Integer-N PLL Synthesizer 1.2 GHz | Analog Devices (Tape & Reel)
The Analog Devices ADF4216BRU-REEL is a dual RF PLL frequency synthesizer delivering a 550 MHz to 1.2 GHz RF output with an integer-N phase-locked loop architecture, packaged in a 20-lead TSSOP. It combines a low-noise digital phase frequency detector (PFD), a precision charge pump, programmable reference and RF/IF dividers, and a 3-wire serial interface in a single RF/IF local oscillator (LO) solution. A PLL frequency synthesizer is a closed-loop timing device in which a voltage-controlled oscillator (VCO) output is phase- and frequency-locked to a stable reference source through a phase frequency detector and charge pump. It sits in the RF and IF signal chain of wireless transmitters and receivers, converting a single low-frequency reference into the high, spectrally pure local oscillator tones required for up-conversion and down-conversion. The hierarchy runs from phase-locked loop to frequency synthesizer to clock and timing IC to integrated circuit. The ADF4216 supports programmable reference, RF, and IF N-divider ratios, selectable charge pump currents, and selectable dual-modulus prescalers of 16/17 for the IF chain and 64/65 for the RF chain. Because the loop is integer-N, the synthesizer frequency is the reference frequency multiplied by an integer ratio, giving excellent phase noise and very low reference feedthrough at the cost of fractional-N flexibility. A dedicated power-down mode shuts the part down for leakage control between burst transmissions. Operated from a 3 V to 5.5 V supply, the device integrates everything a designer needs for a dual-LO transceiver front end: two independent synthesizer channels that can drive both the RF and IF sections of a wireless receiver or transmitter. The 3-wire serial interface allows the divider ratios, prescaler, charge pump, and counter settings to be loaded from a host microcontroller or baseband processor. Typical applications include GSM and CDMA wireless handsets, wireless local loop and base-station equipment, WCDMA and TD-SCDMA transceiver front ends, RFID readers, microwave and satellite up/down converters, and instrumentation. In each case the device replaces separate oscillators and dividers while tightening phase noise and reducing board area. When designing around the ADF4216, pay close attention to loop filter component selection, reference phase noise, and the charge pump setting. A mismatched charge pump current and bandwidth combination produces high reference spurs, while an aggressive loop bandwidth trades phase noise for lock time. Keep the reference and RF traces short and well decoupled, and follow the grounding and decoupling layout recommended in the manufacturer datasheet. This page combines verified distributor and manufacturer information with drop-in alternatives, a parameter-by-parameter comparison table, and practical design notes that go beyond the raw datasheet tables, helping engineers shortlist, source, and lay out the part with confidence.
ADF4216BRUZ - 1.2GHz Dual PLL Synthesizer | Analog Devices
The Analog Devices ADF4216BRUZ is a dual RF phase-locked-loop frequency synthesizer with a maximum output frequency of 1.2 GHz in a 20-lead TSSOP package. It integrates a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, and programmable dual-modulus prescaler for RF and IF local-oscillator generation. The device operates from a 2.7 V to 5.5 V supply and uses a 3-wire serial interface for programming. A frequency synthesizer is a clock-generation and timing component that locks an output signal to a stable reference frequency. In a programmable PLL, a phase-frequency detector compares the divided output with the reference signal, while a charge pump and loop filter convert phase error into a control voltage that tunes the voltage-controlled oscillator. This architecture belongs to the hierarchy of PLL frequency synthesizer, clock generator, timing IC, and semiconductor. The ADF4216 family supports selectable charge-pump currents and dual-modulus prescalers. The listed RF prescaler is 64/65, with an IF prescaler option of 16/17. Its maximum synthesis frequency is 1.2 GHz, while the family also supports a 550 MHz operating mode. The 3-wire serial interface allows a host processor to set divider, reference, charge-pump, and prescaler parameters for the target channel plan. The device is intended for wireless receiver and transmitter architectures that require local oscillators for RF up-conversion, RF down-conversion, or IF sections. Its dual-channel architecture can supply separate RF and IF local-oscillator signals, reducing the number of synthesis paths required in a multi-band transceiver. Reference-divider flexibility allows the reference frequency to be accommodated without redesigning the complete PLL configuration. Typical uses include microwave radio equipment, wireless transceiver modules, IF-generating receiver chains, and instrumentation requiring programmable frequency generation. Design work should account for loop-filter bandwidth, reference phase noise, charge-pump settings, prescaler selection, and output-divider ratios. The voltage-controlled oscillator and charge-pump loop must be optimized together to achieve the required phase noise and lock behavior. Because the PLL reference, feedback divider, and output divider determine the synthesized frequency, verify every ratio against the programming table in the manufacturer datasheet before releasing a PCB. Keep the serial programming traces away from sensitive RF and reference paths, provide stable decoupling at the supply pins, and follow the manufacturer’s recommended loop-filter component values to avoid changing lock time or phase-noise performance. This page combines the family-level technical specifications, package and interface details, application guidance, and drop-in replacement analysis needed to evaluate the ADF4216BRUZ before it is placed into an RF or IF clock-generation design.
ADF4216BRUZ-RL - 1.2 GHz Integer-N PLL | Analog Devices
Analog Devices ADF4216BRUZ-RL is an integer-N clock and frequency synthesizer with a maximum synthesis frequency of 1.2 GHz, a selectable 3:1 input-to-output ratio, and a 20-pin TSSOP package measuring 4.40 mm in body width. The device combines a PLL with dual-modulus prescaler support and selectable charge-pump currents for programmable frequency generation. A phase-locked loop, or PLL, is a frequency-control circuit that compares a reference signal with a divided feedback signal and adjusts a controlled oscillator until the phase and frequency match. Within the clock and timing hierarchy, the ADF4216BRUZ-RL is an RF/IF clock-frequency synthesizer, a PLL-based timing IC used to derive stable local signals for communication, instrumentation, and test systems. The ADF4216BRUZ-RL supports reference or intermediate-frequency prescaler choices of 16/17 and RF prescaler choices of 64/65. Its maximum listed synthesis frequency is 1.2 GHz, and the device includes selectable charge-pump currents for loop design flexibility. A 5.5 V power-supply figure is identified for this family, while the 3-wire programming arrangement supports digital control of operating parameters. The synthesizer uses an integer-N PLL architecture, providing a direct integer division relationship between the controlled oscillator and reference frequency. That architecture is useful when the required output can be related cleanly to the reference through integer feedback division. The dual-modulus prescaler permits adjacent prescale ratios to be selected, supporting practical divider arrangements while retaining a programmable synthesizer structure. Typical uses include local oscillator generation for RF and IF signal chains, precision clock generation for measurement equipment, and local frequency references in communication receivers and transmitters. The 20-pin TSSOP format also supports compact surface-mount layouts where board area and assembly cost are important. System designers should verify lock-range, phase-noise, reference, and loop-filter requirements against the manufacturer datasheet for the selected operating mode. For a stable implementation, use a clean reference source, keep the feedback divider routing compact, and place loop-filter components close to the relevant device pins. Verify the programmed divider ratio, reference frequency, charge-pump setting, and VCO frequency plan before closing the layout. Proper grounding and return paths are especially important when the synthesized clock is close to high-speed digital or RF circuitry. This page combines the exact device identity, verified package and frequency characteristics, drop-in candidate analysis, technical comparisons, and practical PLL layout guidance. It also identifies engineering parameters that require confirmation in the manufacturer datasheet, helping designers distinguish a true pin-compatible replacement from a superficially similar frequency synthesizer.
ADF4217LBRU - Dual RF/IF Integer-N PLL | Analog Devices
The Analog Devices ADF4217LBRU is a low-power dual RF/IF integer-N phase-locked loop frequency synthesizer with a 3 V nominal supply, a maximum supply current of 10 mA, and a 20-terminal TSSOP surface-mount package. It can generate local-oscillator signals for the RF and intermediate-frequency sections of wireless receivers and transmitters. Its industrial temperature range extends from -40 °C to +85 °C. An integer-N PLL is a frequency synthesizer that uses feedback from a programmable divider to lock an output frequency to a stable reference. The phase-frequency detector compares the divided feedback signal with the reference, while the charge pump drives the loop filter and voltage-controlled oscillator. The resulting architecture provides programmable frequency synthesis with phase and frequency regulation controlled by the external loop-filter components. The ADF4217 family combines a low-noise digital phase-frequency detector, a precision charge pump, a programmable reference divider, and programmable RF and IF output paths. These functions support dual-channel local-oscillator architectures, allowing one synthesizer to serve both RF and IF sections. The low 3 V nominal operating supply also makes the device suitable for compact, power-conscious RF and communication equipment. As an integer-N synthesizer, the device divides its internal oscillator frequency by an integer value derived from the programmed RF or IF output path. The programmed output therefore remains locked to the external reference frequency multiplied by the applicable integer division ratio. Designers must select reference, divider, charge-pump-current, and loop-filter values with sufficient phase margin for the intended channel spacing and tuning bandwidth. Typical uses include wireless receiver and transmitter local oscillators, RF up-converters and down-converters, IF-generation stages, industrial RF links, test and measurement equipment, and communication hardware. The dual RF/IF architecture is especially useful when both sections require coherent signals derived from one reference source. A key implementation consideration is the loop filter. Its resistance and capacitance set loop bandwidth, damping, reference-spur behavior, and phase margin. Place the loop-filter components close to the relevant device pins, maintain a continuous ground return, and follow the pin-description and reference-layout tables in the Analog Devices ADF4217L data sheet when assigning PCB traces. This product page combines the manufacturer’s device description with practical selection guidance, application analysis, lifecycle information, and verified source links. It also distinguishes the confirmed TSSOP ordering code from package or temperature variants that require separate qualification before being treated as interchangeable replacements.
ADF4218BRU - 2.5GHz Dual RF PLL Synthesizer | Analog Devices
The Analog Devices ADF4218BRU is a dual, integer-N RF PLL frequency synthesizer covering 550 MHz to 2.5 GHz, with a 2.7 V to 5.5 V supply and a 20-pin TSSOP package. It provides independent synthesizers for RF and IF local oscillators in wireless receiver and transmitter circuits, using a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, programmable integer divider, and selectable dual-modulus prescaler. A phase-locked loop, or PLL, is a feedback-controlled timing circuit that locks an output oscillator to a stable reference frequency. The oscillator and voltage-controlled oscillator form the complete frequency synthesizer, while the ADF4218BRU handles reference division, phase detection, charge-pump current generation, programmable integer-N division, and prescaling. In the wider semiconductor hierarchy, it is a clock-and-timing IC and frequency synthesizer used for RF signal generation and frequency conversion. The device supports RF prescaler choices of 16/17 or 64/65 and selectable charge-pump currents. Its three-wire serial interface allows reference frequency, prescaler, integer-N counter, charge-pump, and band-select programming. Available dual-synthesizer configurations include 550 MHz/1.2 GHz, 550 MHz/2.0 GHz, and 550 MHz/2.5 GHz, depending on the selected variant and operating setup. Each synthesizer path uses a digital phase-frequency detector to compare a divided feedback signal with the divided reference. The resulting phase error drives the charge pump and external loop filter, which in turn control a VCO. Designers select loop bandwidth, reference division, charge-pump current, and filter components to balance phase noise, lock time, spur performance, and reference-multiplier requirements. Typical uses include wireless handset RF and IF local oscillators, GSM receivers and transmitters, wireless infrastructure, instrumentation, and other RF up-conversion or down-conversion systems. The 20-pin TSSOP package is also suitable for compact, surface-mounted frequency-generation boards where the external VCO and loop filter can be placed close to the RF signal path. When designing around the ADF4218BRU, preserve the datasheet-specified decoupling and keep the reference, loop-filter, and VCO connections compact. The integrated divider and detector simplify frequency planning, but phase noise, lock range, and spur performance still depend heavily on the external VCO, loop filter, reference quality, and board layout. This page combines verified manufacturer and distributor information with practical PLL design considerations, source-backed alternatives, and a parameter comparison. It highlights where the ADF4218BRU fits and where ADF4216BRU, ADF4217BRU, or the web-referenced ADF4212LBRUZ-RL may require further qualification before substitution.
ADF4218LBRU - Dual Integer-N RF/IF PLL | Analog Devices
Analog Devices ADF4218LBRU is a low-power dual RF/IF integer-N phase-locked loop synthesizer with a 2.6 V to 3.3 V single supply, 7.0 mA total supply current, and a 20-pin TSSOP package. The two synthesizer channels can generate local-oscillator signals for RF and intermediate-frequency sections in wireless receivers and transmitters. Its programmable architecture supports frequency synthesis, channel selection, modulation-related signal generation, and closed-loop phase control. An integer-N PLL is a frequency-synthesis building block that locks the phase and frequency of an output to a reference signal. In the broader device hierarchy, a PLL is a clock-and-timing integrated circuit, a frequency synthesizer, and ultimately a phase-locking signal-processing component. The ADF4218L integrates two synthesis channels so a transceiver can use coordinated RF and IF local-oscillator signals while sharing a reference and digital control interface. The ADF4218L operates from a 2.6 V to 3.3 V supply and is compatible with 1.8 V logic. Its 7.0 mA total supply current suits low-power RF and IF signal chains where both channel count and supply efficiency are important. Selectable dual-modulus prescaler values and programmable charge-pump currents provide flexibility when balancing fractional spur performance, phase noise, lock time, and tuning range. The separate VP connection extends the available tuning range. Internally, the device combines a low-noise digital phase-frequency detector, a precision charge pump, programmable reference division, programmable feedback division, dual-modulus prescalers, and a complete dual integer-N PLL architecture. The digital phase-frequency detector compares the divided feedback signal with the divided reference. The charge pump then drives the voltage-controlled oscillator until the phase and frequency error is corrected. Typical uses include wireless receiver and transmitter local oscillators, dual-band RF conversion systems, IF signal generation, frequency-hopping equipment, and instrumentation requiring precise phase locking. Because the ADF4218L provides both RF and IF synthesis functions, it can reduce the number of separate synthesizer devices in architectures where coordinated reference-derived frequencies are required. Designers should review the pin description and reference circuitry in the Analog Devices data sheet before assigning tracks. Pay particular attention to loop-filter components, charge-pump settings, VCO interface components, reference routing, and decoupling. A practical 20-pin TSSOP layout should minimize high-current return paths and keep the reference and feedback connections away from noisy switching nodes. This page organizes the ADF4218LBRU specifications, verified sourcing context, same-package replacement options, application guidance, and PCB-focused design notes. It also highlights where an existing board can be reused without changing its TSSOP-20 footprint, while requiring normal electrical review of frequency range, reference voltage, loop settings, and channel requirements.
ADF4251BCP - 3.0 GHz Fractional-N Synthesizer | Analog Devices
Analog Devices ADF4251BCP is a dual fractional-N/integer-N frequency synthesizer with 3.0 GHz fractional-N operation, 1.2 GHz integer-N operation, and a 3.3 V power supply in a 24-terminal surface-mount chip carrier package. It combines fractional-N or integer-N synthesis with programmable dual-modulus prescalers, a 3-wire serial interface, programmable charge-pump currents, digital lock detect, and power-down control. A frequency synthesizer is a timing IC that generates a controlled output frequency from a stable reference. A fractional-N synthesizer can achieve fractional division ratios while retaining the coarse tuning range associated with integer-N architecture. Within the broader hierarchy, the ADF4251BCP is a PLL frequency synthesizer, a clock-and-timing IC, and a semiconductor intended for RF local-oscillator generation and signal conversion. Key features include RF prescaler options of 4/5 and 8/9, a programmable IF prescaler, and a separate charge-pump supply that permits an extended tuning voltage. The 3-wire serial interface enables digital programming, while digital lock detect provides a hardware indication of synthesizer lock status. These controls are useful when the oscillator must be adjusted in real time or monitored by a host controller. The synthesizer is intended to operate with an external voltage-controlled oscillator and loop filter, completing a phase-locked-loop implementation. Its fractional-N maximum operating frequency is 3.0 GHz, whereas its integer-N maximum is 1.2 GHz. The supplied source information does not provide the complete prescaler selection matrix, reference-frequency limits, minimum channel spacing, phase-noise values, tuning-voltage limits, or register map, so those values remain unverified in this record. Typical uses include RF local oscillators, upconversion and downconversion paths, wireless communication infrastructure, test-and-measurement equipment, and frequency-generation systems. The separate VP connection can be valuable when the external VCO and loop-filter design requires a tuning voltage beyond the range supported by the synthesizer supply itself. Designers should treat the ADF4251BCP as the synthesizer element rather than a complete standalone oscillator. The external VCO, loop filter, reference source, decoupling network, and controlled impedance layout directly determine lock range, phase noise, spur performance, and tuning accuracy. Verify all register settings and interface timing against the manufacturer datasheet before firmware and PCB release. This product record combines verified manufacturer capabilities, distributor availability references, package information, application guidance, and a strict comparison of the ADF4251 family. It also separates documented facts from unavailable electrical details, helping engineers evaluate the ADF4251BCP without introducing unverified substitute or pricing claims.
ADF4252BCP - 3 GHz Dual Fractional-N PLL | Analog Devices
The Analog Devices ADF4252BCP is a dual fractional-N/integer-N frequency synthesizer with RF operation up to 3 GHz, integer-N operation up to 1 GHz, and a 24-lead LFCSP package with exposed pad. It operates from a 3.3 V power supply, provides a separate VP connection for extended tuning voltage up to 5 V, and provides programmable RF prescalers of 4/5 and 8/9. Its three-wire serial interface supports digital programming of the dual synthesizer architecture. A frequency synthesizer is a clock-and-timing integrated circuit that generates a programmable output frequency from a stable reference. The ADF4252 belongs to the phase-locked-loop hierarchy: fractional-N or integer-N frequency synthesizer → phase-locked loop → clock generator and timing IC. This type of device is used when an RF system requires a locally controlled oscillator with fine frequency resolution and direct digital programming. The dual architecture permits independent RF and IF synthesis paths, which is valuable in wireless receivers and transmitters requiring both an RF local oscillator and an intermediate-frequency local oscillator. The RF section reaches 3 GHz, while the integer-N range reaches 1 GHz. The programmable dual-modulus prescaler supports integer-N and fractional-N operation, and programmable charge-pump currents allow loop behavior to be adapted for different reference and phase-noise requirements. A reported phase-noise figure of 103 dBc/Hz at a 5 kHz offset is identified for GSM-related operation. The manufacturer data sheet also describes a narrow-loop filter configuration intended to meet steady-state spurious specifications, using the lowest charge-pump current for normal operation and the maximum setting during a fast-lock frequency jump. This technique separates acquisition performance from final steady-state performance. Typical applications include RF upconversion and downconversion in wireless receivers, RF transmitters, GSM-compatible communication equipment, instrumentation, and other systems requiring independently programmed RF and IF local oscillators. The 3.3 V core supply and programmable serial interface simplify integration with embedded control hardware. A key design consideration is reference and loop planning. The reference frequency, prescaler, feedback divider, charge-pump current, and loop-filter values must be selected together to meet both phase-noise and lock-time targets. The separate VP supply should also be evaluated against the required tuning-voltage range rather than assumed to follow the digital supply automatically. This page consolidates the verified manufacturer specifications, distributor information, package details, replacement findings, and practical design considerations into one engineering-oriented reference for evaluating the ADF4252BCP in RF and IF frequency-generation systems.
ADF4252BCPZ - 3 GHz Dual Fractional-N PLL | Analog Devices
The Analog Devices ADF4252BCPZ is a dual fractional-N and integer-N frequency synthesizer with a maximum frequency of 3 GHz, housed in a 24-lead WFQFN exposed-pad CSP package. It generates independent RF and IF local-oscillator signals for wireless receiver and transmitter systems. The RF synthesizer uses a sigma-delta fractional-N architecture, while the device also supports integer-N operation for applications requiring integer frequency division. A frequency synthesizer is a timing-control semiconductor that uses a phase-locked loop, or PLL, to convert a stable reference frequency into an accurately programmable output. In its dual-channel form, the ADF4252 supports two synthesis paths within one package, reducing board area in RF and IF chains that require multiple local oscillators. The device must be paired with an external voltage-controlled oscillator and loop filter to complete each PLL. The ADF4252BCPZ features a programmable reference divider, a low-noise digital phase-frequency detector, and a precision charge pump in each synthesizer section. Its fractional-N RF channel allows fine frequency resolution without requiring an unusually high reference frequency. The manufacturer documentation also describes fast-lock operation, where the charge-pump current is increased during a frequency jump and then returned to the setting required for narrow-loop steady-state spurious performance. Control uses a simple SPI-compatible serial interface. The serial data input, serial clock, and latch-enable signals transfer 24-bit words into the appropriate internal latch. This architecture permits programming of divider, charge-pump, reference, and fractional-N settings from a host microcontroller or programmable-logic controller. Register-map details, timing, and recommended control sequences should be implemented from the manufacturer datasheet. Typical applications include wireless transceiver local oscillators, IF conversion stages, radio-frequency test equipment, microwave communication links, and instrumentation requiring independent programmable RF and IF frequencies. The integrated dual-synthesizer architecture is especially useful when board area is constrained but two phase-locked loops are required. A successful design must account for reference-clock jitter, loop-filter bandwidth, VCO phase noise, charge-pump current, RF output power, supply sequencing, and the exposed-pad thermal path. Place input and output decoupling capacitors close to their associated pins, keep the SPI routing compact and ground-referenced, and provide a low-impedance ground connection to the exposed pad. This product page consolidates the manufacturer's device description, package information, interface details, replacement guidance, and application-specific design guidance into a focused engineering reference for evaluating the ADF4252BCPZ in a dual-PLL RF design.
ADF4350ABCPZ - 4.4 GHz Fractional-N PLL | Analog Devices
Analog Devices ADF4350ABCPZ is a wideband fractional-N or integer-N phase-locked-loop frequency synthesizer with an integrated voltage-controlled oscillator, a 2200 MHz to 4400 MHz fundamental VCO range, and RF output frequencies down to 137.5 MHz through selectable divide-by-1/2/4/8/16 outputs. The device is packaged in a 32-lead WFQFN package with an exposed pad and is identified by Analog Devices as a production part. A frequency synthesizer is a timing and RF integrated circuit that locks a voltage-controlled oscillator to a stable reference frequency. The ADF4350 belongs to the phase-locked-loop family, combining a PLL synthesizer, programmable frequency dividers, an RF output stage, and an integrated VCO. This integration allows a compact RF signal source to be built from one synthesizer IC, an external reference, an external loop filter, and passive RF-matching components. The ADF4350 supports both fractional-N and integer-N synthesis, giving designers a choice between fine frequency resolution and integer channel spacing. Its integrated VCO covers 2200 MHz to 4400 MHz, while the divider network extends the usable RF output range to 137.5 MHz. Pin-controlled and software-controlled output muting provide additional ways to manage signal availability, isolation, and test conditions without removing the synthesizer from the circuit. The external reference and loop filter are central to achieving useful phase-noise and lock performance. Reference quality, loop bandwidth, charge-pump settings, divider selection, and component placement all influence the final spectrum. Because the VCO and output circuitry operate at high RF frequencies, layout must minimize loop-filter pickup, preserve a short RF return path, and provide adequate decoupling around the device supplies. Typical uses include wireless infrastructure, test and measurement equipment, frequency-agile local oscillators, radio equipment, and microwave signal generators. The ADF4350ABCPZ is particularly appropriate when one component must cover multiple RF bands while retaining programmable output frequency and programmable output division. Designers should select external capacitors and the loop filter from the manufacturer's application guidance, verify the reference and output interfaces against the pin description, and confirm thermal and RF performance at the intended carrier frequency. The exposed thermal pad should be connected to the ground plane using the manufacturer-recommended thermal-via pattern so that heat is removed effectively and RF return currents remain controlled. This product page combines the manufacturer's synthesis capabilities with practical pin, application, replacement, layout, and sourcing guidance. It also distinguishes genuine pin-compatible alternatives from related devices that may differ in frequency range, qualification, divide ratio, or operating temperature.
ADF4350BCPZ - Wideband Synthesizer w/ Integrated VCO | ADI
The Analog Devices ADF4350BCPZ is a wideband frequency synthesizer with an integrated voltage controlled oscillator (VCO) that operates on a fundamental output frequency range of 2200 MHz to 4400 MHz. Housed in a 32-lead LFCSP (5 mm x 5 mm) exposed-pad package, the part enables fractional-N or integer-N phase-locked loop (PLL) implementations when paired with an external loop filter and an external reference frequency. Divide-by-1/2/4/8/16 output dividers extend usable RF outputs as low as 137.5 MHz. A PLL frequency synthesizer is a closed-loop feedback system that compares a divided VCO output to a reference oscillator and adjusts the VCO tuning voltage until the divided frequency phase-locks to the reference. Fractional-N division enables finer frequency resolution than integer-N at the cost of additional noise-shaping circuitry, while integer-N mode delivers the lowest in-band phase noise. ADF4350 supports both modes, letting engineers trade off resolution against phase-noise performance for applications ranging from cellular base stations to test instrumentation. Key features include an output frequency span of 137.5 MHz to 4400 MHz, a 3-wire SPI-compatible serial interface for register programming, an auxiliary RF output that can be muted independently, and a phase-frequency detector (PFD) that supports reference frequencies up to 200 MHz. The integrated VCO eliminates the need for a discrete resonator, simplifying BOM and reducing board area in radio designs. According to the Analog Devices datasheet, the part supports channel spacing down to a sub-1 Hz resolution when used in fractional-N mode with proper modulator settings. The architecture combines a high-resolution sigma-delta modulator, a low-noise charge-pump, and a wideband VCO that is prescaled for stable locking across process and temperature variations. The mute function is both pin- and software-controllable, allowing the part to be shut down during idle periods in time-division duplex systems to save power. Typical applications include cellular base-station transceivers (GSM, UMTS, LTE, 5G FR1), microwave point-to-point and point-to-multipoint links, satellite communications up-converters, wireless backhaul infrastructure, and bench-top RF signal generators. The 32-lead LFCSP package provides a compact thermal envelope suitable for dense multi-radio boards. When designing with the ADF4350BCPZ, route the charge-pump supply through a ferrite bead and bypass it with a 10 nF cap to minimize reference spurs, and place the loop-filter components as close to the CP and VT pins as practical. Avoid routing digital SPI lines adjacent to the RF outputs to prevent crosstalk into the synthesized spectrum. This page synthesizes distributor pricing, drop-in alternatives drawn from the Analog Devices family, and practical layout notes that complement - but do not replace - the manufacturer datasheet.
ADF4350BCPZ-RL - 4.4 GHz Fractional-N PLL | Analog Devices
Analog Devices ADF4350BCPZ-RL is a fractional-N or integer-N radio-frequency phase-locked-loop frequency synthesizer with an integrated voltage-controlled oscillator, a fundamental VCO range of 2200 MHz to 4400 MHz, and a maximum listed output frequency of 4.4 GHz. The device is packaged in a 32-lead WFQFN exposed-pad, 5 mm × 5 mm surface-mount package and is specified for operation from −40°C to +85°C. A wideband frequency synthesizer converts a stable external reference into an output locked to that reference through a phase-locked loop. The ADF4350 integrates the VCO, fractional-N and integer-N PLL circuitry, programmable reference and feedback dividers, and RF output stages. This integration reduces the number of external RF components while retaining precise frequency control for communications, instrumentation, radar, and test-equipment systems. Key features include operation over a 2200 MHz to 4400 MHz fundamental VCO range and output frequencies down to 137.5 MHz through divide-by-1, divide-by-2, divide-by-4, divide-by-8, or divide-by-16 circuits. The output stage can be muted by hardware or software control, which is useful when multiple RF paths share an antenna or when a transmitter must disable its RF output during calibration or standby. Technically, the ADF4350 supports both fractional-N synthesis for fine channel spacing and integer-N synthesis for integer division relationships between the reference and output. It requires an external reference frequency and external loop-filter components. Designers therefore select the loop bandwidth, reference divider, feedback divider, and VCO tuning word together to balance phase noise, lock time, spur performance, and output-frequency resolution. Typical applications include wireless communication test equipment, local-oscillator generation for RF receivers and transmitters, radar and electronic-warfare systems, frequency-generation instruments, and industrial RF control systems. Its integrated VCO is particularly useful where a compact, PCB-level frequency source is required without a separate oscillator assembly. The primary layout consideration is keeping the RF output connections short and providing a controlled reference and ground arrangement around the exposed pad. Power delivery and thermal relief must be designed for the dissipation produced by the selected output power and operating frequency. The external loop filter also requires careful component selection and placement because its response directly affects PLL stability and phase noise. This page combines the ADF4350BCPZ-RL architecture, frequency and package characteristics, verified sourcing information, documented family alternatives, and practical design guidance. It helps engineers evaluate loop-filter design, RF layout, thermal implementation, and replacement planning without relying on distributor summary pages alone.
ADF4350BCPZ-RL7 - 4.4 GHz Fractional-N PLL | Analog Devices
The Analog Devices ADF4350BCPZ-RL7 is a fractional-N or integer-N phase-locked-loop frequency synthesizer with an integrated voltage-controlled oscillator, designed for RF signal generation up to 4.4 GHz. The device accepts an external reference frequency and uses an external loop filter, allowing the synthesizer bandwidth, output frequency, and channel spacing to be configured for the target system. It is packaged in a 32-lead WFQFN exposed-pad CSP and specified for operation from -40°C to +85°C. A phase-locked loop is a feedback-controlled oscillator used to generate a stable output frequency from a reference signal. In the broader device hierarchy, the ADF4350BCPZ-RL7 is a clock-and-timing IC, specifically a PLL frequency synthesizer with an integrated VCO. Fractional-N operation divides the reference frequency by an integer value plus a programmable fraction, supporting fine frequency increments without requiring a high reference frequency. Integer-N mode provides a conventional integer divider path. The principal features of this synthesizer include support for both fractional-N and integer-N architectures, an integrated VCO, an external reference input, and programmable frequency synthesis through a serial interface. The 4.4 GHz upper operating frequency makes the device suitable for radio-frequency front ends, test equipment, instrumentation, and communication modules whose local oscillator or clock source must be adjustable over a wide frequency range. The exposed thermal pad supports heat transfer from the IC to the PCB copper area. The ADF4350BCPZ-RL7 uses a phase detector, programmable divider chain, charge-pump output, and integrated VCO to close the PLL loop. An external passive loop filter connects the charge pump to the VCO control input and determines major loop dynamics. Designers therefore need to select filter components for the intended reference frequency, division ratios, phase-noise requirement, and settling time rather than treating the loop filter as a fixed accessory. Typical applications include wireless transceiver local oscillators, RF test and measurement instruments, frequency-generating test equipment, industrial RF control modules, and communication infrastructure. The device is especially appropriate when one synthesizer platform must cover several output frequencies and the system can configure the frequency through its digital control interface. It can also support integer-N use cases where fractional channel spacing is unnecessary. PCB implementation requires careful treatment of the RF output, reference input, ground return paths, supply decoupling, and exposed-pad thermal design. Place the loop-filter components close to the charge-pump and VCO-control pins, connect the exposed pad to a properly sized ground plane, and follow the manufacturer's package and evaluation-board layout recommendations to preserve RF performance and phase-noise behavior. This page combines the product identity, package information, purchasing guidance, application analysis, and drop-in-family comparisons in a form designed for rapid engineering review. It also identifies when an ADF4350BCPZ-family device can simplify a design without requiring a different board footprint.
ADF4351BCPZ - 4.4 GHz Fractional-N PLL Synthesizer | Analog Devices
The Analog Devices ADF4351BCPZ is a fractional-N or integer-N phase-locked-loop frequency synthesizer with an integrated voltage-controlled oscillator, a 2.2 GHz to 4.4 GHz fundamental VCO range, and operation up to 4.4 GHz. The device accepts a 10 MHz to 250 MHz reference input and is supplied in a 32-lead VFQFN exposed-pad package. It supports programmable integer and fractional frequency synthesis through an external reference and loop filter. An RF frequency synthesizer generates a stable, programmable output by locking a voltage-controlled oscillator to a reference through a phase-locked loop. The ADF4351 belongs to the PLL synthesizer and clock-generator hierarchy, integrating the synthesizer, VCO, programmable dividers, reference and feedback paths, and RF output circuitry. This integration reduces board-level design effort while retaining the flexibility required for external loop-filter optimization. According to the Analog Devices product page and datasheet, the ADF4351 supports fractional-N and integer-N synthesis, includes an integrated VCO, and is intended for wideband RF applications. The 10 MHz to 250 MHz input range and 2.2 GHz to 4.4 GHz fundamental VCO range make it suitable for microwave communication, wireless infrastructure, test equipment, radar-related RF signal chains, and frequency-agile RF systems. Its fractional-N operation permits fine frequency resolution when the reference and N-divider settings are selected appropriately. The device requires an external loop filter and external reference frequency. Filter component selection affects loop bandwidth, phase noise, reference-spur behavior, lock time, and the amount of ripple presented to the VCO control node. Designers should evaluate loop dynamics for each output frequency rather than assuming one filter network is optimal across the full 2.2 GHz to 4.4 GHz range. The exposed pad provides the required thermal and electrical connection to the PCB. Typical implementation places the ADF4351 between a stable reference source and an RF load or receiver/transmitter signal chain. The output can be filtered, buffered, or mixed according to the system requirement. Keep the reference and loop-filter connections short, provide clean supply decoupling, and use a controlled-impedance RF layout for the output path. Verify phase noise, spur levels, lock behavior, output power, and temperature performance with the final reference and filter implementation. For direct replacement, verify package dimensions, exposed-pad construction, pin assignments, register compatibility, reference range, VCO range, and supply limits. A similar frequency range alone is insufficient for drop-in use. This page combines verified manufacturer and distributor information with practical PLL design considerations, comparison fields, and sourcing-oriented FAQ answers. Pricing and availability should be confirmed with authorized distributors as of 2026-10-21.
ADF4351BCPZ-RL7 - 4.4GHz Integrated-VCO PLL | Analog Devices
The Analog Devices ADF4351BCPZ-RL7 is a fractional-N or integer-N wideband frequency synthesizer with an integrated voltage-controlled oscillator, covering output frequencies from 35 MHz to 4400 MHz. It accepts a 10 MHz to 250 MHz reference input, operates from a 3.0 V to 3.6 V supply, and is offered in a 32-lead LFCSP package with an exposed pad for improved thermal performance. The -40 °C to +85 °C grade supports industrial-temperature RF and instrumentation designs. A frequency synthesizer is a PLL-based clock-generation device that locks a voltage-controlled oscillator to an external reference. In the broader electronics hierarchy, the ADF4351 belongs to clock and timing ICs, phase-locked loops, and RF frequency synthesizers. Its integrated VCO reduces board area by eliminating a separate oscillator, while an external reference and loop filter allow the design engineer to tune phase noise, reference spur performance, and channel spacing. Principal features include support for both fractional-N and integer-N architectures, a wide 35 MHz to 4.4 GHz tuning range, and a 32-lead exposed-pad package. These characteristics suit local oscillators, wireless infrastructure, frequency-agile test equipment, and RF signal-chain clocking. The exposed pad conducts heat away from the die and must be connected to a low-impedance ground plane on multilayer PCBs. The device uses a programmable register interface to configure the output frequency, divider settings, prescaler, charge-pump current, reference path, and diagnostic functions. Register programming determines the final output waveform and phase-noise behavior, so firmware must sequence power-up correctly and wait for the synthesizer to report lock before treating the RF output as valid. Typical applications include wireless base-station and backhaul equipment, cellular and satellite test systems, microwave down-converters, laboratory frequency sources, and low-cost spectrum-analysis instruments. For designs above 1 GHz, controlled reference routing, short RF traces, and a properly designed loop filter are essential for stable lock and acceptable phase noise. The main engineering trade-off is flexibility versus implementation effort. Although the integrated VCO simplifies the RF front end, the ADF4351 still requires a stable reference, an external loop filter, correct register configuration, and careful exposed-pad grounding. Use the manufacturer evaluation-board schematic and register guidance as the starting point for a new PLL design. This page consolidates the device specifications, pin-package characteristics, qualified alternatives, comparison data, and practical PLL design guidance into one engineering reference. It also identifies which parameters require confirmation from the full manufacturer datasheet before schematic release or production layout.
ADF4355-2BCPZ - 4.4 GHz PLL with Integrated VCO | Analog Devices
The Analog Devices ADF4355-2BCPZ is a fractional-N and integer-N phase-locked-loop frequency synthesizer with an integrated low-noise voltage-controlled oscillator, covering RF output frequencies from 54 MHz to 4400 MHz. It uses a 32-pin WFQFN exposed-pad package and supports analog and digital supplies from 3.15 V to 3.45 V, while the charge-pump and VCO supplies operate from 4.75 V to 5.25 V. The part includes hardware and software power-down modes for controlled system operation. A phase-locked loop is a feedback-controlled timing system that locks an internal voltage-controlled oscillator to a stable reference frequency. In the ADF4355-2, the reference signal, frequency divider, phase detector, charge pump, external loop filter, VCO, and output stages form a programmable RF synthesis system. This architecture allows an external reference and loop filter to establish channel spacing, tuning resolution, phase noise, and lock behavior. The ADF4355-2 supports fractional-N operation with a 38-bit modulus and integer-N operation for applications requiring different tuning schemes. Its RF output frequency range extends from 54 MHz to 4400 MHz, making the device suitable for communication transmitters, test equipment, instrumentation, radar-related signal sources, and frequency conversion stages. Programmable output power and programmable integer and fractional divider values provide flexibility across a wide range of RF designs. The device accepts a reference frequency range of 10 MHz to 500 MHz according to the manufacturer product information. The external loop filter is a key circuit element: its components determine loop bandwidth, reference spur suppression, phase noise, and lock time. The ADF4355-2 therefore supports both simple integer-N channel plans and higher-resolution fractional-N frequency plans without requiring a separate VCO. Typical implementation places the ADF4355-2 in an RF signal chain between a stable reference source and the powered RF section. The synthesizer generates a programmable carrier, while the external loop filter shapes the closed-loop response. Keep the reference and feedback traces short, use a controlled ground return, and place bypass capacitors close to the supply pins. Power-down modes can be useful in battery-powered or intermittently operating systems because they reduce activity when the RF output is not required. The main design trade-off is loop-filter complexity. Fractional-N operation improves frequency resolution, but it also requires careful spur planning and often more demanding layout practice. Integer-N mode can simplify spur behavior for applications that do not need fine channel spacing. The manufacturer datasheet should guide the register sequence, reference setup, loop-filter calculation, and final performance validation. This product page combines the ADF4355-2BCPZ electrical identity, pin and package information, drop-in alternatives, comparison points, and practical RF design guidance. It is intended to help engineers select the correct synthesizer variant, plan the loop filter, and integrate a low-noise programmable RF source without overlooking supply, reference, layout, or power-management constraints.
ADF4355-3BCPZ - 6.6 GHz Fractional-N PLL | Analog Devices
The Analog Devices ADF4355-3BCPZ is a fractional-N and integer-N phase-locked loop frequency synthesizer with an integrated voltage-controlled oscillator, a 6.6 GHz RF output capability, and programmable output power. It is packaged in a 32-lead WFQFN exposed-pad surface-mount package for compact RF and microwave designs. An integrated wide-band VCO allows the ADF4355-3 to generate frequencies from approximately 35 MHz to 6.6 GHz using fractional-N or integer-N synthesis. Its RF output supports programmable power levels, while output dividers provide flexible frequency generation for receiver and transmitter signal chains. An external reference clock and loop filter are required for normal closed-loop operation. The device uses separate analog and digital power rails operating from 3.15 V to 3.45 V. Charge-pump and VCO power rails accept 4.75 V to 5.25 V, allowing the RF section to operate with a higher supply while digital control logic remains on a 3.3 V rail. Both hardware and software power-down modes are available for shutdown and duty-cycle control. The ADF4355-3BCPZ is designed for frequency-agile communication equipment, wireless infrastructure, microwave radios, test and measurement instruments, and phased-array or clock-generation subsystems. Its programmable output power helps optimize the link budget when the downstream mixer, power amplifier, or receiver does not require maximum drive. Designers must account for the exposed thermal pad when laying out the PCB. The package ground connection and exposed pad should be tied to a low-impedance ground plane with adequate via density, and the loop filter should be positioned close to the charge-pump pins. The operating temperature range is -40°C to +105°C, covering industrial and extended-temperature environments.
ADF4355BCPZ - 6.8GHz Fractional-N PLL | Analog Devices
Analog Devices ADF4355BCPZ is a fractional-N or integer-N phase-locked-loop frequency synthesizer with an integrated voltage-controlled oscillator, an RF output range of 54 MHz to 6800 MHz, and a 32-WFQFN exposed-pad package. The device supports 1.8 V logic compatibility, 3.3 V analog and digital supplies, and typically 5.0 V charge-pump and VCO supplies. Its programmable output division ratios are 1, 2, 4, 8, 16, 32, or 64, while the dual-modulus prescaler and 38-bit modulus support fine frequency resolution. A fractional-N frequency synthesizer generates a stable, programmable output frequency by combining a phase-locked loop, a frequency divider, and a high-resolution modulus. The ADF4355 belongs to the broader hierarchy of clock-generation ICs, frequency synthesizers, phase-locked loops, and RF timing components. Integrating the VCO reduces the number of external microwave components needed to implement a tunable local oscillator, although an external reference, loop filter, and passive matching network are still required. Key features include operation to 6.8 GHz, low phase noise from the integrated VCO, programmable charge-pump current, programmable reference dividers, digital and analog lock detection, and hardware or software power-down. The 38-bit modulus permits fractional-N synthesis with high nominal frequency resolution. Programmable output division extends the usable RF range and allows integer-N or fractional-N configurations to be selected according to phase-noise, spur, and tuning requirements. Technically, the ADF4355 uses an integrated wideband VCO with programmable output division and a dual-modulus prescaler for fractional-N operation. The reference path divides an external source before phase comparison with the divided VCO output. An external passive loop filter converts the phase-detector charge-pump current into the control voltage applied to the VCO. The exact loop bandwidth, reference ratio, and filter values therefore determine lock range, settling time, phase noise, and fractional-N spur performance. Typical applications include microwave and millimeter-wave test equipment, frequency conversion in communications receivers, local-oscillator generation for RF front ends, radar or satellite signal-chain prototypes, and instrumentation requiring programmable RF outputs. The integrated VCO is particularly useful where a fixed local-oscillator module would be too restrictive or where several frequencies must be generated from one reference source. The exposed thermal pad must be connected to a low-impedance ground plane, and the RF output requires careful impedance-controlled routing. Component placement should minimize loop-filter area and keep sensitive control and supply paths away from the RF output. Designers must also verify regulator tolerances, charge-pump settings, reference phase noise, and loop-filter calculations before operation across the full frequency range.
ADF4355BCPZ-RL7 - 6.8 GHz Fractional-N PLL Synthesizer | Analog Devices
The Analog Devices ADF4355BCPZ-RL7 is a fractional-N or integer-N frequency synthesizer with an integrated voltage-controlled oscillator, covering 54 MHz to 6800 MHz in a 32-lead WFQFN exposed-pad package. It supports a 38-bit fractional modulus, 1.8 V-compatible logic, selectable RF output division, and separate 3.3 V and 5.0 V supply domains. The device is supplied on a 7-inch tape-and-reel reel and operates from -40°C to +85°C. A fractional-N frequency synthesizer generates an accurate output frequency by combining a phase-locked loop with an integrated VCO and programmable divider. Its frequency resolution is set by a high-order fractional modulus, while integer-N operation provides a simpler configuration for applications that do not require fractional feedback. The ADF4355 belongs to the PLL synthesizer family within clock and timing integrated circuits, where it serves as a programmable RF clock source for communications, test equipment, and signal-generation systems. The integrated VCO eliminates the need for an external VCO, reducing board area while supporting RF outputs up to 6.8 GHz. A 38-bit modulus enables fine channel spacing, and the output divider can be programmed from divide-by-1 through divide-by-64. The 3-wire control interface operates with 1.8 V-compatible logic, allowing direct connection to low-voltage control hardware. Analog and digital power are supplied at 3.3 V, while the charge-pump and VCO supply arrangement uses 5.0 V typical operation. A practical implementation includes an external reference source, reference divider, loop filter, and output-matching network. The external loop filter determines loop bandwidth, phase noise, spur performance, and lock time, so component selection and PCB placement are as important as the synthesizer settings. Register programming controls the channel frequency, fractional value, output division, reference path, and power state. Hardware and software lock-detect functions support reliable frequency acquisition in production systems. Typical uses include microwave and wideband RF signal generation, wireless communications test equipment, local oscillator generation, radar test systems, and instrumentation requiring programmable frequencies between 54 MHz and 6.8 GHz. The device is particularly useful when one synthesizer must cover multiple output dividers and closely spaced fractional-N channels without using multiple separate VCO assemblies. For a reliable layout, place the loop-filter components and RF matching network close to their associated pins, maintain short return paths around the exposed pad, and follow the Analog Devices recommended decoupling arrangement. Confirm the external reference level and loop-filter values against the operating channel, divider ratio, and required phase-noise performance before production release. This product page consolidates the RF frequency range, supply requirements, package information, application guidance, comparison considerations, and drop-in candidate assessment into one engineering-focused reference for ADF4355BCPZ-RL7 designs.
ADF4356BCPZ - 6.8 GHz PLL Synthesizer | Analog Devices
Analog Devices ADF4356BCPZ is an integrated wideband fractional-N and integer-N phase-locked-loop frequency synthesizer with an on-chip voltage-controlled oscillator, one clock output, and a maximum synthesized output frequency of 6800 MHz. It uses a 3-wire serial interface for register programming and is housed in a 32-lead LFCSP package with an exposed pad. A frequency synthesizer is an electronic timing component that generates, divides, multiplies, or modulates a reference frequency to produce a controlled output. In the wider hierarchy, an ADF4356BCPZ is a PLL frequency synthesizer, a clock-and-timing IC, and a semiconductor used to establish stable frequencies for communication, instrumentation, radar, and test systems. Its integrated VCO eliminates the separate VCO required by many conventional synthesizer architectures. The key operating characteristics include a 6800 MHz upper output frequency, support for fractional-N or integer-N synthesis, and operation across several output-divider ranges. The Analog Devices manufacturer datasheet describes output operation from 53.125 MHz to 6800 MHz through a series of frequency dividers. The device also provides controllable output muting through both a dedicated pin and the serial programming interface. Three-wire serial control simplifies connection to a microcontroller, FPGA, or embedded processor while allowing the synthesizer to be programmed without manual component adjustment. The PLL requires an external reference source and loop filter. Fractional-N operation supports fine frequency synthesis, while integer-N operation is useful when the required output frequency is an integer multiple of the reference frequency. Mute control can suppress the output during setup or sensitive measurement intervals. The analog and digital power rails accept 3.15 V to 3.45 V, while the charge-pump and VCO rails accept 4.75 V to 5.25 V. Hardware and software power-down modes reduce consumption when synthesis is not required. Typical uses include wireless communication test equipment, radar and electronic-warfare signal chains, frequency-hopping systems, phase-noise-sensitive receivers, and laboratory frequency generators. Designers should separate sensitive supply paths, follow the exposed-pad grounding and thermal-layout guidance, and select the external loop-filter components for the required channel bandwidth, reference frequency, and phase-noise target. Because fractional-N multiplication increases the VCO tuning rate, loop design and spur performance require joint evaluation rather than relying only on the nominal output frequency. This page combines the manufacturer specifications with application guidance, replacement analysis, and board-level design considerations. It also identifies where an exact drop-in substitute is appropriate and where a different PLL or VCO architecture is required because of frequency-range, package, control, or phase-noise differences.
ADF4356BCPZ-RL7 - 6.8 GHz PLL Synthesizer | Analog Devices
The Analog Devices ADF4356BCPZ-RL7 is a fractional-N or integer-N phase-locked-loop frequency synthesizer with an integrated voltage-controlled oscillator, a maximum RF output frequency of 6.8 GHz, and a 32-lead WFQFN exposed-pad package. Its fundamental VCO covers 3400 MHz to 6800 MHz, while programmable dividers extend the usable RF output range down to 53.125 MHz. A frequency synthesizer is a clock-and-timing IC that locks an internal voltage-controlled oscillator to an external reference frequency. The ADF4356 belongs to the phase-locked-loop family, where the phase-locked-loop synthesizer hierarchy supports stable RF carrier generation for integer-N channels or fine fractional-N channel spacing. The device requires an external reference, loop filter, and passive loop-filter components to complete the feedback network. Key features include programmable fractional-N and integer-N operation, an integrated VCO, output division by 1, 2, 4, 8, 16, 32, or 64, hardware and software power-down modes, and pin-programmable or software-controlled RF output muting. Analog and digital power rails operate from 3.15 V to 3.45 V, while the charge pump and VCO supply operate from 4.75 V to 5.25 V. These separate supply domains support careful partitioning of noisy, sensitive, and digital circuitry. The synthesizer architecture allows the loop bandwidth, reference path, channel spacing, and output frequency to be configured through its serial programming interface. Its RF output stages can generate fundamental VCO frequencies or divided outputs as low as 53.125 MHz. The external loop filter remains a critical analog network because it converts phase-detector current into the VCO control voltage and directly influences phase noise, reference spur performance, lock time, and channel-to-channel isolation. Typical applications include 6 GHz wireless infrastructure, microwave backhaul, radar test equipment, satellite and microwave communications, RF instrumentation, and local-oscillator generation for mixers or upconverters. The 6.8 GHz ceiling is particularly useful for short-wavelength wireless systems operating near the lower portion of the 6 GHz band. For lower-frequency equipment, the output divider reduces the fundamental oscillator frequency without requiring a second synthesizer. PCB implementation should preserve the integrity of the reference, charge-pump, loop-filter, and RF output paths. Place the loop-filter components close to their associated pins, keep the exposed thermal pad connected to a low-impedance ground plane, and follow the manufacturer reference design for component values and trace geometry. Account for the added Register 13 when moving from ADF4355-based firmware to the ADF4356 initialization sequence. This page combines manufacturer specifications, verified commercial availability, replacement analysis, and application-specific engineering guidance to support component selection and board bring-up. It also distinguishes direct physical replacements from related synthesizers whose frequency range, control interface, or firmware requirements make them less suitable for a drop-in substitution.
ADF4360-0BCP - 2600MHz Integer-N VCO Synthesizer | Analog Devices
Analog Devices ADF4360-0BCP is a fully integrated integer-N frequency synthesizer and voltage-controlled oscillator designed for a 2600 MHz center frequency, with an optional divide-by-2 output covering 1200 MHz to 1360 MHz. The device is housed in a 24-lead WFQFN exposed-pad package and combines a PLL frequency synthesizer, VCO, and programmable output stages in one RF component. An integer-N synthesizer belongs to the phase-locked-loop and frequency-generation hierarchy. Its feedback divider compares a divided RF output with a reference signal, while the internal voltage-controlled oscillator changes frequency as the loop control voltage varies. This architecture supports stable, programmable RF generation for communications, test equipment, radar, and instrumentation systems without requiring a separate VCO. The ADF4360-0BCP is specifically positioned around the 2600 MHz center-frequency range and includes a divide-by-2 function for lower-frequency operation. This distinction is important because the divide-by-2 path broadens the functional output range while retaining one integrated RF synthesizer assembly. Its integer-N feedback architecture avoids fractional-N spur considerations, although channel spacing and reference-path design remain important when planning a compliant receiver or transmitter. The 24-lead WFQFN exposed-pad package supports compact surface-mount layouts and provides a thermal pad beneath the device for heat spreading. Because an RF synthesizer and VCO dissipate power locally, PCB construction, exposed-pad soldering, grounding, and loop-filter layout can materially affect phase noise, tuning stability, and thermal performance. A continuous, low-impedance ground plane and careful separation of sensitive RF and digital return paths are therefore essential. Typical uses include 2.6 GHz wireless infrastructure, microwave data links, radar test systems, RF instrumentation, frequency-agile signal sources, and local-oscillator generation. The divide-by-2 capability is useful when a system also needs an output between 1200 MHz and 1360 MHz, provided the output path and downstream circuitry are matched to the selected frequency and power condition. When planning this part, verify the exact reference frequency, required channel spacing, output power, loop-filter values, RF output configuration, and temperature range against the manufacturer datasheet before schematic release. Keep the RF output path short, preserve the exposed-pad ground connection, and test the closed loop across its intended frequency range rather than relying only on isolated VCO measurements.
ADF4360-0BCPZRL - 2.6 GHz Integer-N PLL with VCO | Analog Devices
The Analog Devices ADF4360-0BCPZRL is an integrated integer-N frequency synthesizer with a voltage-controlled oscillator, designed for a 2600 MHz center frequency and supplied in a 24-lead LFCSP package with an exposed pad. Its reference input accepts signals from 10 MHz to 250 MHz, and the RF output can be divided by two to produce frequencies from 1200 MHz to 1360 MHz. The device uses a three-wire serial control interface for programming. An integer-N PLL synthesizer generates a stable output frequency by comparing a divided reference signal with a feedback signal from an internal VCO. The VCO converts this phase error into a control voltage that adjusts the oscillator to lock the feedback divider at the requested ratio. When the divide-by-2 output is selected, the same synthesizer can support lower-frequency RF outputs without changing the external package or control architecture. The principal features of this device include its integrated synthesizer and VCO, 2600 MHz center-frequency design, selectable divide-by-2 RF output, three-wire serial programming, and a compact exposed-pad package. These characteristics simplify RF clock and local-oscillator designs by combining the frequency-generating functions in one component rather than requiring a separate integer-N PLL and VCO. The ADF4360 belongs to the PLL and frequency-synthesizer hierarchy, which also includes clock generators, RF synthesizers, local oscillators, and phase-locked loops. Integer-N synthesizers are especially useful when relatively simple integer feedback ratios and direct digital programming are preferred. The architecture is suitable for wireless infrastructure, test equipment, microwave conversion stages, and other systems requiring programmable RF sources. Choose the -0 variant only when its specified frequency band covers the intended output. Other ADF4360 band options share the 24-lead LFCSP footprint and serial interface, but their VCO ranges differ and can require different prescaler, divisor, or band-plan settings. Confirm the required register settings and loop-filter values against the manufacturer datasheet before converting an existing design. Keep the RF output path short and use controlled-impedance routing on the PCB. The exposed pad must be connected to the ground plane with adequate thermal-via density, because power loss in the VCO and output stages can raise junction temperature. Place the loop-filter components close to their associated pins and follow the reference-design layout to minimize phase noise degradation and unwanted coupling. This product page consolidates the key electrical characteristics, band-family alternatives, package information, and practical RF layout guidance into one engineering reference. Use the manufacturer datasheet for the complete register map, electrical characteristic tables, and recommended application circuits.