Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
PCA9507DP,118 - 2-Wire Bus Extender, 5V, 8-TSSOP | NXP
The NXP PCA9507DP,118 is a 2-wire serial bus extender with integrated 3.3 V to 5 V level shifting, one bidirectional I²C/SMBus channel, and a 400 kHz maximum clock rate, packaged in an 8-pin TSSOP (SOT505-1, DP suffix). It provides bidirectional buffering of SDA and SCL lines while preserving all I²C operating modes (master/slave, multi-master, arbitration) across the level-shift boundary, and it extends the usable bus length up to 18 meters for HDMI DDC, I²C-bus, and SMBus links. The device operates from a 2.7 V to 5.5 V supply and is specified across the -40 °C to +85 °C industrial temperature range. What is an I²C bus extender? An I²C bus extender (also called a bus repeater or accelerator) is a type of interface IC that sits between two segments of a 2-wire serial bus and buffers both SCL (clock) and SDA (data) lines. Its purpose is twofold: to overcome capacitive loading limits that cap I²C bus length, and to translate voltage levels between dissimilar supply domains. The PCA9507 sits in the broader hierarchy of bus interface ICs (interface IC > bus extender > signal buffer/repeater), and is a specialized sibling of the I²C hub/switch family such as the PCA9543A. Key features of the PCA9507DP,118 include: 1 channel of buffered SDA + SCL; support for Standard-mode (100 kHz), Fast-mode (400 kHz), and 3.4 MHz Fast-mode Plus overshoot tolerant operation on the upstream port; 2.7 V to 5.5 V supply range; 218 ns typical propagation delay; and integrated rise-time accelerators that allow designers to drop the bus pull-up resistors while still meeting rise-time budgets on long cables. It also provides hot-swap insertion tolerance so that cards can be plugged into a live backplane without corrupting the bus. The internal architecture uses two N-channel MOSFET pass gates with charge-pump enhancement, plus direction-sensing comparators that automatically configure the channel as upstream or downstream. The upstream (master-side) port tolerates 3.3 V to 5 V, while the downstream port can operate down to 2.7 V, enabling typical 3.3 V-to-5 V HDMI DDC level shifting. The TSSOP-8 footprint makes the part suitable for compact HDMI connector breakouts, display modules, and embedded backplanes. Typical applications include HDMI/DVI Display Data Channel (DDC) level shifters, I²C-bus extension over long cables (up to 18 m) in industrial control panels, SMBus fan and chassis management links, and any board-to-board 2-wire link that must bridge a voltage-level or capacitive-load gap. Because the device preserves arbitration and clock-stretching behavior, it is safe to insert in the middle of an existing multi-master bus. When designing with the PCA9507, remember that the part is a pure bus extender with no pull-ups on either side. Both upstream and downstream segments still require external pull-up resistors sized to the segment capacitance, and the device's quiescent current (typically a few hundred microamps) must be included in the system power budget. For long cables, place the PCA9507 near the connector to keep the high-impedance stub short. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes for HDMI DDC and long-cable I²C applications - context not collected in the manufacturer datasheet alone.
PCA9509D - 400 kHz I2C Level Translator | NXP
The NXP Semiconductors PCA9509D is a 400 kHz, two-channel I2C-bus and SMBus level-translating repeater housed in an 8-pin SO package. It allows a processor operating at a lower voltage to communicate with standard I2C-bus or SMBus input/output devices operating at a higher voltage. The device provides bidirectional signal translation while preserving the open-drain structure required by these two-wire buses. An I2C level translator is an interface IC within the broader hierarchy of serial-interface devices, bus-interface controllers, interface circuits, and semiconductors. This category solves voltage-domain mismatches between processors and peripherals without requiring every connected device to operate from the same supply voltage. The PCA9509 is particularly useful when the processor-side logic voltage and the peripheral-side bus voltage differ but both devices use open-drain signaling. The PCA9509D supports operation up to 400 kHz and provides two translated channels. Its two-channel arrangement allows one SDA and one SCL signal to cross between voltage domains. The translated arrangement preserves standard bus behavior, including wired-AND signaling through open-drain outputs and the need for appropriate pull-up resistors on each voltage domain. According to the NXP product information, the PCA9509 is intended to bridge a processor's low-voltage two-wire serial bus to conventional I2C-bus or SMBus I/O. The eight-pin surface-mount package supports compact interface isolation on industrial and embedded boards. Because the translator operates bidirectionally, both sides can initiate or acknowledge transactions without separate directional buffers. Typical uses include low-voltage microcontrollers interfacing with higher-voltage sensors, EEPROMs, real-time clocks, analog converters, and bus-management devices. It can also extend a processor-based control system to a legacy SMBus peripheral, provided the voltage domains, pull-up networks, capacitance, and bus speed remain within the device's operating limits. PCB design should treat each voltage domain as a separate pull-up network. Confirm the supply levels, pull-up values, bus capacitance, and maximum clock rate before implementation. The 400 kHz rating makes bus timing and rise-time verification especially important when cable length or slow pull-up resistors are present. This page organizes the PCA9509D interface function, package characteristics, candidate drop-in alternatives, application guidance, and design considerations for faster component selection and PCB planning.
PCA9509DP,118 - I2C/SMBus Level Translating Repeater | NXP
The NXP PCA9509DP,118 is a level translating I2C-bus/SMBus repeater that enables a processor low-voltage 2-wire serial bus to interface with standard I2C-bus or SMBus I/O, providing bidirectional buffering for both the SDA (data) and SCL (clock) lines at up to 400 kHz in an 8-pin TSSOP (SOT505-1) package. An I2C repeater (also called a bus buffer or redriver) is an interface IC that regenerates the two-wire serial signals so that capacitive loading and voltage-level differences do not limit bus length or device count. Within the interface-IC hierarchy (repeater -> bus buffer -> I2C/SMBus controller -> communication interface IC), repeaters sit between a low-voltage processor side and a higher-voltage peripheral side, keeping rise times and logic thresholds compliant on both segments. Key features include dual-supply level translation, supporting a low-voltage side and a standard 3 V to 5.5 V bus side, and bidirectional buffering that extends the I2C-bus by isolating capacitance on each segment. The device retains all operating modes and features of the I2C-bus system during level shifts, including clock stretching and multi-master arbitration behavior. A typical propagation delay of 109 ns and a low 2 pF input capacitance keep timing margin comfortable even at the 400 kHz fast-mode ceiling, while 5 mA supply current suits power-conscious designs. Technically, the PCA9509 uses open-drain buffer stages with rise-time acceleration so both bus segments retain true open-drain behavior: contention and backplane noise are not passed between segments, and the parts act as fault isolators between a captive processor bus and a larger peripheral bus. Typical applications include extending I2C from an MCU to backplanes and card cages, level-shifting between 1.x V/1.8 V/2.5 V processors and 3.3 V/5 V SMBus peripherals in servers, telecom line cards, and industrial control panels where bus capacitance would otherwise exceed the 400 pF I2C limit. Design-wise, plan pull-up resistor values per segment: each buffered side requires its own pull-ups sized for that segment's total capacitance, since the repeater isolates the two sides electrically. This page synthesizes distributor pricing, availability data, and practical design guidance not found in the manufacturer datasheet, with all parameters traced to NXP and distributor sources as of 2026-10-20.
PCA9510ADP,118 - Hot-Swap I2C/SMBus Buffer | NXP Semiconductors
The NXP Semiconductors PCA9510ADP,118 is a hot-swappable I2C-bus and SMBus bus buffer that allows I/O card insertion into a live backplane without corrupting the data and clock buses. It is supplied in an 8-pin TSSOP (SOP) surface-mount package and buffers one channel of the two-wire serial bus at operating speeds up to 400 kHz. An I2C bus buffer (also called a bus repeater or redriver) is a two-wire interface IC that sits between an I2C or SMBus controller segment and a downstream segment. Within the interface IC hierarchy - serial interface ICs to buffers/repeaters to logic ICs - its role is to isolate bus capacitance, extend the number of devices or cable length a bus can drive, and protect one segment from faults or transients on the other. The defining feature of the PCA9510A is its hot-swap control circuitry. During card insertion, contact bounce and partial power-up can corrupt SDA and SCL lines; the PCA9510A keeps the backplane side disconnected until a stop command or bus idle condition occurs on the backplane without bus contention on the card side. Only then does it make the bidirectional connection, preserving data integrity on the live backplane. Technically, the buffer provides bidirectional buffering with rise-time acceleration on the output sides, allowing larger bus capacitance than a raw I2C port can tolerate. It supports both the standard I2C-bus and the SMBus (System Management Bus) protocol and operates from a single supply, making it a drop-in isolation element between a backplane and a removable I/O card. Typical applications include live-insertion I/O cards in telecom and server backplanes, CompactPCI-style shelves, SMBus segments in power supplies and battery-backed systems, and any hot-pluggable module that must not disturb an operating two-wire bus during insertion or removal. Design consideration: keep the two bus segments physically separated on the PCB and provide adequate pull-up resistors sized for each segment's capacitance; the buffer does not eliminate the need for correct pull-up values on either side. This page synthesizes distributor pricing context, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with all electrical data traced to the NXP PCA9510A product data sheet (Rev. 01, 8 September 2005).
PCA9510D - 400kHz Hot-Swappable I2C Buffer | NXP
The NXP Semiconductors PCA9510D is a hot-swappable I2C-bus and SMBus buffer operating at up to 400 kHz in an 8-pin SO package. It enables I/O-card insertion into a live backplane while control circuitry delays connection of the card-side bus until the backplane is idle or a STOP command is detected. This prevents bus contention and corruption of data and clock signals during card insertion. An I2C bus buffer is a specialized interface IC that electrically isolates or buffers two bus segments while preserving bidirectional serial-data and clock communication. The PCA9510D belongs to the interface-IC hierarchy used in hot-plug, expansion-card, server, and embedded backplane systems. Its SMBus compatibility extends the same isolation concept to systems using SMBus-based management or control functions. The device operates as a single-channel, 400 kHz bus buffer. Its key function is controlled connection between the backplane and card sides: the card is not connected during an active bus transaction, reducing the risk of contention when either bus segment is active. The 8-SO package supports conventional surface-mount PCB assembly, while the PCA9510D,118 ordering suffix identifies a specific distributor orderable variant. The PCA9510D is intended for systems in which modules may be inserted or removed without powering down the entire host. NXP describes the device as providing bidirectional bus buffering once the connection is permitted. The relevant engineering benefit is operational continuity and reduced insertion disturbance rather than longer trace distance or level translation; no galvanic isolation or voltage-level translation should be inferred from the hot-swap function. Typical uses include server and workstation expansion cards, telecommunications equipment, industrial controller modules, test systems, and embedded backplanes that expose an I2C or SMBus connection to removable hardware. The PCA9510D is particularly relevant when the card connector may be populated or serviced while the host remains active and the bus must not be corrupted during insertion. Design attention should focus on system enable control, power sequencing, bus idle detection, and the electrical behavior of the card-side connector. The protection mechanism depends on observing a valid bus condition before connecting the two segments. Designers should therefore verify startup states, fault conditions, and connector sequencing rather than treating the PCA9510D as an ordinary passive I2C buffer. This page combines the manufacturer function description, package and frequency information, orderable part references, and practical hot-plug guidance to support PCB, sourcing, and replacement decisions. It also distinguishes verified device identity from specifications that require confirmation against the manufacturer datasheet before electrical sign-off.
PCA9511D - Hot-Swappable I2C/SMBus Buffer | NXP
The NXP Semiconductors PCA9511D is a one-channel hot-swappable I2C and SMBus bus buffer operating from 2.7 V to 5.5 V, with distributor listings identifying a 400 kHz bus speed and an 8-pin SOIC package. It is intended for systems where removable cards connect to, or disconnect from, an operating I2C or SMBus backplane without corrupting the data and clock buses. A hot-swappable bus buffer is an interface IC that isolates two bus segments while a card is inserted or removed. Its control circuitry prevents electrical disturbance from the newly connected or disconnected card from propagating across the active bus. Within the interface hierarchy, the PCA9511D belongs to the I2C and SMBus buffer class, which sits beneath bus transceivers and broader interface ICs used to protect, isolate, or route communications links. The principal device characteristics are a 2.7 V to 5.5 V supply range, support for I2C and SMBus signaling, a nominal 400 kHz operating rate, and an 8-pin SOIC package. The buffer function allows equipment makers to use the same backplane architecture across cPCI, VME, AdvancedTCA, and similar multipoint backplane systems where field-replaceable cards may be inserted into a running system. The PCA9511D separates the bus side connected to the insertion or removal event from the host-side communication path. This isolation is functionally important because connector transients and card power-state transitions can otherwise disturb clock and data waveforms. The NXP product page identifies the device as discontinued, so it should be treated as a legacy component for maintenance, repair, and previously qualified system support rather than a new-design preference. Typical uses include hot-pluggable cPCI and VME controller cards, AdvancedTCA line cards, embedded backplane interfaces, and other I2C or SMBus systems that require controlled card insertion or removal. The 400 kHz bus designation also places the device in legacy low-speed bus applications rather than newer high-speed I2C designs. When designing around the PCA9511D, preserve the bus-side and card-side separation described by the manufacturer datasheet, validate connector and card power-up sequencing, and verify signal integrity in the completed backplane. PCB changes are generally unnecessary when replacing the same 8-pin SOIC device, but functional and lifecycle qualification must precede substitution. This product record combines lifecycle, electrical, package, sourcing, cross-reference, and replacement guidance with practical hot-plug design considerations. It also distinguishes true pin-to-pin options from superficially similar I2C switches and multiplexers that require different control, channel-count, or bus-isolation behavior.
PCA9512AD - Hot-Swap I2C/SMBus Buffer, 3.3V-5V | NXP
The NXP PCA9512AD is a level-shifting, hot-swappable I2C-bus and SMBus buffer housed in an 8-pin SOIC package, providing bidirectional buffering for one channel at up to 400 kHz. It integrates two dedicated supply pins (VCC1 and VCC2) that allow independent 3.3 V and 5 V rails to coexist on the same bus while preserving maximum noise margin on each side. The device prevents backplane data/clock corruption during live card insertion by isolating the precharge voltages of the I/O card from the active backplane rails. An I2C/SMBus buffer is a bus repeater/accelerator that isolates two segments of a multi-drop serial bus, supports level translation between mixed-voltage nodes, and optionally accelerates the rising transitions of the SCL/SDA open-drain lines. Buffers sit between a controller and its peripherals, between two bus segments on a backplane, or between a host and removable card. The PCA9512 family belongs to NXP's broader bus-interface category, positioned between simple repeaters (e.g., PCA9507) and full multi-channel hubs (e.g., PCA9548). Hot-swap capability requires a precharge circuit that gently biases SCL/SDA before the card connector mates, avoiding the inrush glitches that would otherwise corrupt bus traffic. Key features of the PCA9512AD include 3 mA sink capability on each side per the I2C specification, support for bus voltages from 2.0 V to 5.5 V on either supply rail, and compatibility with Standard, Fast, and Fast-Plus (400 kHz) I2C modes. The buffer provides offset voltage between the two bus segments to prevent input-to-output latch-up, and it includes rise-time accelerator circuitry that minimizes bus settling time on heavily loaded segments. The 8-SO package is pin-compatible with the PCA9509 and other 8-pin I2C buffers, simplifying PCB layout reuse. The PCA9512AD is built on NXP's sub-micron CMOS process and uses an internal charge pump to drive the gate of the accelerator FETs, ensuring consistent rise-time performance across temperature. The dual-rail architecture allows designers to mix 3.3 V and 5 V devices on the same physical bus without external level translators, and the offset-impedance design prevents bus contention during simultaneous master access. ESD protection exceeds 2 kV HBM on the SCL/SDA pins. Typical applications include hot-swap I/O cards in telecom base stations, ATCA/cPCI backplane signal buffering, server management buses (IPMB, PMBus), and mixed-voltage I2C sensor aggregation. The device is commonly used where 3.3 V MCUs must communicate with 5 V legacy peripherals on the same bus segment. When designing with the PCA9512AD, ensure that VCC1 and VCC2 decoupling capacitors are placed within 2 mm of their respective supply pins. The offset voltage between bus segments must be accounted for in voltage-margin calculations, and live-insertion sequencing must guarantee that the I/O card's SCL/SDA lines reach the buffered idle state before the connector fully mates. Note: per the NXP product page, the PCA9512AD is End-of-Life, so designers should validate last-time-buy opportunities for production runs. This page synthesizes distributor pricing, drop-in alternatives, and practical design guidance that goes beyond the manufacturer datasheet, helping engineers make informed replacement and supply-chain decisions for this EOL part.
PCA9512D - 2.7V Hot-Swap I2C Buffer | NXP Semiconductors
NXP Semiconductors PCA9512D is a hot-swappable I2C and SMBus buffer designed for level shifting between host and peripheral sections of a live bus. The device operates from a 2.7 V to 5.5 V supply, supports operation up to 400 kHz according to the distributor product listing, and has a specified propagation delay of 5.0 ns. It is packaged in an 8-pin SOIC. An I2C bus buffer is an interface IC that divides a potentially long or electrically incompatible bus into separate buffered segments. The PCA9512D adds hot-swap capability so that an I/O card can be inserted into a powered backplane without corrupting the data or clock buses. This function places it within the hierarchy of I2C interface IC, bus buffer, level translator, and interface semiconductor. The principal benefit is electrical isolation between the two sides of the buffer. Each side can present a defined low-level output through the I2C bus output characteristics, while the device provides independent conductive paths for SDA and SCL. The listed operating supply range supports both 3.3 V and 5 V system environments, and the 400 kHz bus rating accommodates standard-speed I2C communication used by many embedded, industrial, and expansion-card systems. A hot-swappable buffer typically contains a conventional bidirectional I2C data channel and a clock-channel arrangement designed to isolate the card-side bus from the host-side bus. This separation reduces the risk that card insertion, removal, or electrical loading on the peripheral side will corrupt an active host transaction. The PCA9512D is therefore useful when system reliability during maintenance or card replacement matters more than the minimal cost and simplicity of a direct bus connection. Typical uses include hot-pluggable I/O cards, industrial backplanes, test systems, mezzanine modules, and embedded expansion boards. In these systems, the PCA9512D can isolate a removable peripheral from the main I2C controller, allowing the peripheral-side wiring and capacitance to be disconnected electrically from the host bus during card replacement. The 5.0 ns propagation delay and 400 kHz operating capability support low-to-moderate-speed control and management buses. PCB implementation requires attention to supply decoupling, trace routing, and the separation between host-side and card-side nets. Keep the clock and data routes short, preserve the ground reference, and place the device close to the bus segment that requires isolation. Because the product is discontinued, engineers should verify the complete system bus capacitance, rise-time, pull-up arrangement, and card-insertion behavior before treating it as a new-design choice. This product page combines the manufacturer status, historical datasheet characteristics, distributor identification, package information, pricing evidence, and practical replacement analysis. It also distinguishes a genuine same-family option from packaging variants or functionally similar interface ICs that do not provide a verified pin-to-pin drop-in path.
PCA9513D - 400kHz SMBus Buffer | NXP Semiconductors
The NXP Semiconductors PCA9513D is a discontinued one-channel hot-pluggable I2C-bus and SMBus buffer rated for operation up to 400 kHz and packaged in an 8-pin SO package. Its primary function is to isolate a bus segment while allowing equipment to be inserted into or removed from a live backplane without corrupting the clock or data traffic. An I2C bus buffer is a specialized interface IC that reproduces logic levels between a master-side bus and a slave-side bus. The buffered side can remain operational during insertion or removal, helping prevent disturbance of a live communication network. In the broader hierarchy, the PCA9513D belongs to the I2C and SMBus interface-controller family, which sits above bus buffers within interface ICs and broader semiconductor power-management and signal-conditioning systems. The principal identified characteristics are one buffered channel, a 400 kHz operating-frequency rating, an 8-pin SOIC-compatible package, and hot-pluggable bus operation. The device is intended to provide bus-segment isolation in systems where modules or plug-in cards can be added dynamically. Because the manufacturer marks PCA9513D as discontinued, its documentation and product information are retained for historical design reference rather than new-product selection. Technically, the PCA9513D uses separate upstream and downstream sides to divide the I2C bus into buffered segments. Its purpose is to improve system behavior during live insertion and removal rather than to increase the standardized bus speed beyond 400 kHz. Designers must still account for capacitance, rise time, pull-up placement, and the electrical behavior of each bus segment when laying out the complete circuit. Typical uses include hot-swappable industrial backplanes, telecommunications equipment with removable line cards, server peripherals, and embedded systems that add or remove bus-connected modules while other devices remain active. The buffer is especially useful where an unplugged card could otherwise disturb the shared clock and data conductors. For a new design, verify the complete I2C system against the PCA9513D datasheet, including absolute maximum ratings, timing, supply requirements, and input thresholds. On an existing board, confirm that the original package footprint and signal assignment match before treating another part as a replacement. In a live system, isolate power as well as data when practical so that insertion transients do not propagate through the bus. This page combines the discontinued-product status, bus-buffer specifications, drop-in replacement assessment, application guidance, and engineering comparison information needed to evaluate the PCA9513D for legacy hardware and controlled replacement programs.
PCA9514D - 400kHz Hot-Swappable SMBus Buffer | NXP
The NXP Semiconductors PCA9514D is a single-channel, 400 kHz hot-swappable SMBus buffer designed to isolate an I2C or SMBus segment while a device is being connected, disconnected, or inserted into a live bus. The component is offered in an 8-pin SO package and is identified by NXP as a hot-swappable IC and SMBus bus buffer. Its principal electrical characteristic in the product record is a 400 kHz bus frequency. An SMBus buffer is an interface IC that separates two bus segments so that capacitance, voltage differences, or temporarily disconnected devices do not disrupt the complete bus. In the wider product hierarchy, this buffer belongs to the I2C and SMBus interface family, which sits within interface ICs and system-level data-management electronics. Unlike a passive series resistor, a buffered hot-plug solution can isolate the bus during insertion or removal while maintaining defined logic levels across the separated segments. The primary advantage of the PCA9514D is hot-swap bus isolation at a maximum stated frequency of 400 kHz. This makes it relevant to systems where modules may be added or removed after power is applied, including expandable industrial equipment, removable control modules, and board-to-board backplanes. The single-channel arrangement allows a designer to isolate one bus branch without introducing a multi-channel or bidirectional buffer architecture. The PCA9514D uses NXP's 8-SO package, a compact surface-mount package suitable for conventional PCB assembly and automated manufacturing. Because it is a dedicated interface device, its principal design concerns are bus logic levels, pull-up placement, enable or connection timing, signal integrity, and the voltage relationship between the two bus sides. Detailed supply limits, channel voltage tolerance, propagation timing, and electrical characteristics should be taken directly from the manufacturer datasheet when those values are required for a production design. Typical uses include hot-pluggable sensor and storage modules, removable front-panel controllers, distributed data-acquisition equipment, and board-to-board I2C links. In an industrial enclosure, the device can help prevent a faulty or newly inserted card from loading the main SMBus. In a portable or modular product, it can support a controlled connection sequence. The buffer does not eliminate the need for correct pull-up resistors or bus timing analysis; it provides the isolation element around which those network decisions are made. Designers should verify enable sequencing, pull-up resistor locations, capacitance, and logic-level compatibility before finalizing the PCB. Keep both sides of the buffer routed with short, continuous return paths, and place associated protection or pull-up components close to their relevant pins. Review the datasheet pin-description and application diagrams when assigning tracks, particularly if a design uses the device for bidirectional bus translation rather than straightforward same-domain buffering. This page combines the NXP product status, package and bus-frequency information with design-focused guidance for obsolete-product review, replacement planning, and hot-pluggable bus architecture decisions. It also separates the exact orderable PCA9514D references from broader interface-design considerations so engineers can evaluate lifecycle constraints without overlooking implementation details.
PCA9515AD - Dual I2C/SMBus Bus Repeater 400kHz | TI (Tape & Reel)
The Texas Instruments PCA9515AD is a dual bidirectional I2C bus and SMBus repeater (buffer/ReDriver) with 2 channels, supporting up to 400 kHz operation, supplied in an 8-pin SOIC package. It operates from a single 2.3 V to 3.6 V supply and its open-drain I2C I/O pins and enable input are 5.5-V tolerant. An I2C bus repeater is an interface buffer that isolates the capacitance and noise of one segment of an I2C or SMBus from another. Within the signal-chain hierarchy (I2C repeater -> bus buffer -> interface IC -> mixed-signal semiconductor), repeaters let a single controller address far more devices or far longer PCB traces and cables than the ~400 pF bus-capacitance limit would otherwise allow, while keeping rise times compliant. Key features include two identical bidirectional open-drain buffer channels, an active-high repeater-enable input (EN) for power-up isolation and bus segmentation, 5.5-V tolerant I2C I/O and EN for mixed-mode 3.3 V/5 V operation, and lockup-free operation that accommodates the clock-stretching and arbitration behavior of multi-master I2C systems. Technically, the PCA9515A is fabricated in a BiCMOS process. Each buffer uses a rising-edge accelerator and direction-sensing scheme that distinguishes a master-driven LOW from a slave-driven LOW, preventing the input-to-output latch-up that plagued first-generation repeaters. Because both channels are identical, the device can be used as two independent 1-bit repeaters or as a single 2-bit bus switch-style buffer. Typical applications include I2C bus segment isolation in servers and telecom cards, capacitive load expansion on long backplanes and cables, level-tolerant buffering between 3.3 V controllers and 5 V legacy peripherals, and SMBus systems in power-management and battery-pack designs. A key design consideration: the buffer is unidirectional-gain per edge, so it must not be used in loops or back-to-back without careful segmentation; place it where the bus capacitance exceeds roughly 400 pF or when isolating a noisy or fault-prone slave segment. This page adds value beyond the datasheet by synthesizing distributor pricing, verified drop-in alternatives, comparison tables, and practical layout guidance in one place.
PCA9515AD/G-T - 400 kHz I2C Bus Repeater | NXP
The NXP PCA9515AD/G-T is a single-channel I2C-bus and SMBus repeater operating up to 400 kHz in an 8-pin SOIC surface-mount package. It buffers both the clock and data lines, allows one upstream I2C bus to drive two downstream buses, and supports bus extensions of up to 400 pF per side. The device uses a proprietary voltage-level translation scheme to improve interoperability between buses operating at different logic levels. An I2C repeater is a bus-interface device placed between two I2C segments so that bus capacitance, rise time, and drive strength do not limit the entire network. The PCA9515A family belongs to the signal-buffer and repeater hierarchy within interface ICs. By placing the repeater near the midpoint of a long bus, distributing it into shorter branches, or isolating a heavily loaded segment, a system can retain more usable bandwidth than with a single unbuffered bus. Key features include a 400 kHz maximum I2C clock rate, one buffered repeater channel, support for two 400 pF bus segments, an enable input for placing the device in a high-impedance state, and operating modes that accommodate mixed voltage domains. The SOIC-8 package provides a small footprint and is widely supported by automated assembly and inspection processes. The PCA9515A does not contain a direction-control pin. Its internal design therefore uses slightly different legal low-voltage levels at the input and output to avoid bus lock-up when traffic can propagate in either direction. Pull-up resistors remain on the I2C bus segments rather than inside the repeater, allowing each segment to use the voltage, resistance, and rise-time values required by its own logic level. Typical uses include voltage-level isolation between I2C buses, extending a controller across multiple cable segments, splitting a long bus into lower-capacitance branches, and isolating noisy or slow peripherals in industrial control, instrumentation, and consumer electronics. It is also useful where a daughter-card connector, ribbon cable, or long PCB trace adds capacitance to SCL and SDA. When laying out the circuit, place the repeater near the load it isolates, route SCL and SDA as a short pair, and provide the required pull-up resistors independently on each bus segment. Confirm that the enable-control state cannot trap the bus during power-up or reset. Because the PCA9515A has no direction pin, verify bidirectional data-flow and arbitration behavior during prototype testing rather than assuming a fixed upstream/downstream command direction. This page combines manufacturer functional information, distributor package and inventory details, published I2C bus-extension characteristics, and application guidance to provide a practical engineering reference for selecting, laying out, and validating the PCA9515AD/G-T.
PCA9515ADG4 - Dual I2C Buffer, 400kHz | Texas Instruments
The Texas Instruments PCA9515ADG4 is a dual-channel bidirectional I2C bus and SMBus repeater operating from 2.3 V to 3.6 V, supporting a maximum bus frequency of 400 kHz in an 8-pin SOIC package. The device contains two identical bidirectional open-drain buffers, an active-high repeater-enable input, and 5.5 V-tolerant I2C inputs. An I2C repeater is a type of bus buffer that regenerates or isolates a bidirectional bus segment. In the broader hierarchy, it is an interface IC, a bus-management IC, and a semiconductor. Unlike a unidirectional logic buffer, each PCA9515ADG4 channel supports signal flow in both directions, allowing the same two pins to participate in an I2C transaction. This makes the device useful when bus capacitance, loading, voltage differences, or physical distance prevents one controller from driving the complete bus reliably. The PCA9515ADG4 provides two bidirectional channels, a 400 kHz operating-rate designation, 5.5 V-tolerant I2C I/O, and a 5.5 V-tolerant enable input. Its open-drain I/O architecture is compatible with the wired-AND behavior required by I2C and SMBus. The specified propagation delay is 113 ns, while input capacitance is 7 pF, characteristics that are important when budgeting capacitive loading and propagation delay across the repeated bus segment. The device requires a supply voltage between 2.3 V and 3.6 V. A typical implementation connects the buffer between a bus-master side and a remote peripheral side, with pull-up resistors placed separately on each side of the repeater. The enable input can hold the buffers in a high-impedance state when the downstream segment must be isolated. The measured 500 µA supply current supports low-power embedded systems while keeping the repeater available for continuous bus operation. Typical uses include extending an I2C sensor bus, isolating a controller from noisy peripherals, separating high-capacitance bus sections, and supporting SMBus-compatible equipment. It is particularly useful when the same PCB contains several addressable sensors, EEPROMs, analog converters, or power-monitoring components. Industrial temperature-grade availability and the compact SOIC-8 footprint make it practical for embedded control and instrumentation systems. For reliable operation, use pull-up resistors on each isolated bus segment and verify that total capacitance, sink-current loading, and timing remain within the limits of every connected device. Keep the repeater-enable net defined so that power-up cannot accidentally leave a downstream segment floating or partially enabled. Check signal polarity and bus direction at the system level because both channels are bidirectional and operate through open-drain pull-ups. This page combines the PCA9515ADG4 electrical characteristics with package information, application guidance, design considerations, and a verified same-package replacement reference. It is intended to help engineers select the correct bus repeater, plan its board layout, and distinguish a true pin-compatible substitute from parts that require PCB changes.
PCA9515ADR - Dual I2C/SMBus Bus Repeater 400kHz | TI
The Texas Instruments PCA9515ADR is a dual bidirectional I2C bus and SMBus repeater (buffer/ReDriver) with 2 channels, supporting up to 400 kHz operation, supplied in an 8-pin SOIC package. It operates from a single 2.3 V to 3.6 V supply and its open-drain I2C I/O pins and enable input are 5.5-V tolerant. An I2C bus repeater is an interface buffer that isolates the capacitance and noise of one segment of an I2C or SMBus from another. Within the signal-chain hierarchy (I2C repeater -> bus buffer -> interface IC -> mixed-signal semiconductor), repeaters let a single controller address far more devices or far longer PCB traces and cables than the ~400 pF bus-capacitance limit would otherwise allow, while keeping rise times compliant. Key features include two identical bidirectional open-drain buffer channels, an active-high repeater-enable input (EN) for power-up isolation and bus segmentation, 5.5-V tolerant I2C I/O and EN for mixed-mode 3.3 V/5 V operation, and lockup-free operation that accommodates the clock-stretching and arbitration behavior of multi-master I2C systems. Technically, the PCA9515A is fabricated in a BiCMOS process. Each buffer uses a rising-edge accelerator and direction-sensing scheme that distinguishes a master-driven LOW from a slave-driven LOW, preventing the input-to-output latch-up that plagued first-generation repeaters. Because both channels are identical, the device can be used as two independent 1-bit repeaters or as a single 2-bit bus switch-style buffer. Typical applications include I2C bus segment isolation in servers and telecom cards, capacitive load expansion on long backplanes and cables, level-tolerant buffering between 3.3 V controllers and 5 V legacy peripherals, and SMBus systems in power-management and battery-pack designs. A key design consideration: the buffer is unidirectional-gain per edge, so it must not be used in loops or back-to-back without careful segmentation; place it where the bus capacitance exceeds roughly 400 pF or when isolating a noisy or fault-prone slave segment. This page adds value beyond the datasheet by synthesizing distributor pricing, verified drop-in alternatives, comparison tables, and practical layout guidance in one place.
PCA9515ADT - 2-Channel 400kHz I2C Buffer | Texas Instruments
The Texas Instruments PCA9515ADT is a two-channel bidirectional I2C bus and SMBus repeater operating from a 2.3 V to 3.6 V supply, supporting I2C operation up to 400 kHz in an 8-pin SOIC package. Its two identical bidirectional open-drain buffer circuits isolate and extend SDA and SCL connections while preserving bidirectional bus behavior. The active-high repeater-enable input provides a straightforward way to place each channel in a high-impedance state when it is not needed. An I2C repeater is an interface IC used to extend or segment a two-wire serial bus. I2C and SMBus systems connect controllers and peripherals through SDA and SCL, with pull-up resistors establishing the high logic level. Within the broader semiconductor hierarchy, a repeater belongs to the interface IC category and ultimately functions as a signal buffer and bus isolator. Adding a repeater can divide a long capacitive bus into shorter sections, reducing the load presented to the controller and improving signal integrity at Fast Mode speeds. The PCA9515A family provides two bidirectional channels, I2C and SMBus compatibility, active-high enable control, open-drain I/O, and mixed-mode signal support. Its I2C input/output pins and enable input are specified as 5.5 V tolerant, allowing interface signals to exceed the device's 3.6 V maximum supply voltage under the stated conditions. The architecture also supports Standard Mode and Fast Mode devices, multiple masters, and powered-off high-impedance I2C pins. The two identical channels make the PCA9515ADT useful for repeating both clock and data. Because the buffers are bidirectional, information can flow from either side of a channel through the same SDA or SCL path. The active-high enable input allows a host or reset controller to disconnect a repeated segment when isolation is required. TI identifies the device as a BiCMOS integrated circuit, combining bipolar and CMOS process characteristics in the same interface component. Typical uses include extending an I2C sensor bus, segmenting a long point-to-point connection, isolating controller and peripheral buses, and supporting mixed-mode systems that include both Standard Mode and Fast Mode devices. The 400 kHz operating capability suits sensors, EEPROMs, expanders, real-time clocks, and other common low-speed I2C peripherals. It can also assist when bus capacitance prevents one controller from reliably driving every attached device directly. Design the surrounding bus carefully because the repeater does not replace pull-up resistors or solve every signal-integrity problem. Place the device near the boundary between bus sections, provide the pull-ups required for each local segment, and confirm that enable control cannot float during power transitions. Review the manufacturer pin-description table when assigning PCB tracks and preserve adequate spacing from unrelated noisy circuitry. This page organizes the device's key electrical characteristics, application guidance, verified drop-in alternatives, and practical integration considerations. It is intended to help engineers compare bus-extension options and implement the PCA9515ADT without overlooking enable-state, voltage-tolerance, or capacitance requirements.
PCA9515AP - 2-Channel 400kHz I2C Repeater | TI
The Texas Instruments PCA9515AP is a dual-channel bidirectional I2C bus and SMBus repeater operating at up to 400 kHz, supplied in an 8-pin PDIP package. Its two open-drain buffer channels support I2C and SMBus systems, while 5.5 V-tolerant I2C inputs and the enable input permit mixed-mode operation. The device operates from a 2.3 V to 3.6 V supply. An I2C repeater is a bidirectional bus buffer that regenerates a bus signal and separates it into two bus segments. It belongs to the interface IC hierarchy, where I2C and SMBus repeaters support communication among controllers, peripherals, sensors, and embedded processors. Unlike a unidirectional level translator, this device detects and forwards activity in either direction, allowing each side of the bus to retain its own pull-up network. The PCA9515A family provides two identical bidirectional open-drain buffers, an active-high enable input with an internal pull-up, and 5.5 V-tolerant bus and enable inputs. Mixed-mode signal operation is supported, while the open-drain I2C structure maintains wired-AND bus behavior. The verified distributor listing identifies the PCA9515AP as a 400 kHz, two-channel buffer in an 8-pin PDIP package. The repeater is built around BiCMOS interface circuitry intended to preserve the open-drain signaling used by I2C and SMBus. Because both sides communicate bidirectionally, bus capacitance, pull-up strength, rise time, and timing margins must be evaluated separately for each segment. The enable input is particularly useful during system reset because it can isolate a misbehaving peripheral, but its state should not change during an active I2C transfer. Typical uses include isolating a high-capacitance I2C bus, connecting sensors or EEPROMs to a remote bus segment, buffering a processor I2C controller, supporting SMBus power-management hardware, and isolating power domains whose logic levels remain compatible with the repeater. It can also help separate a bus into shorter segments when capacitive loading or timing margins become problematic. The primary design consideration is that the PCA9515AP is not a general-purpose bidirectional level shifter. Its supply range is 2.3 V to 3.6 V, and the enabled repeater must maintain compatible logic levels across both bus segments. External pull-up resistors should be placed close to each bus segment, with values selected from the actual capacitance and required rise time rather than copied blindly. This page consolidates verified distributor specifications, the official manufacturer datasheet, package details, application guidance, and honest replacement analysis. It also distinguishes verified drop-in interchangeability from mechanically similar parts that would require PCB changes, helping engineers compare alternatives without treating a same-family option as automatically safe to substitute.
PCA9515APWT - 2-Channel I2C Buffer, 400kHz | Texas Instruments
The Texas Instruments PCA9515APWT is a 2-bit dual bidirectional I2C bus and SMBus repeater designed for extending and conditioning low-speed serial buses. It operates from a 2.3 V to 3.6 V VCC supply and supports operation up to 400 kHz, with two independent bidirectional buffer channels, an active-high repeater-enable input, 5.5 V tolerant I2C I/O, and open-drain I2C interfaces. The device is packaged in an 8-pin TSSOP (PW) package, designated by the PWT ordering suffix and intended for surface-mount assembly. An I2C buffer or repeater is an interface IC that regenerates and electrically isolates a bidirectional bus segment. I2C and SMBus use open-drain signaling, so a buffer can reduce loading, restore signal rise time, isolate capacitive loading, and extend usable bus distance without changing the logical bus protocol. The PCA9515A belongs to the broader signal-buffer and repeater category within interface ICs, supporting embedded systems where a controller, sensor, EEPROM, or other peripheral sits behind a long or heavily loaded interconnect. The main features of the PCA9515APWT include two identical bidirectional buffer channels, 2.3 V to 3.6 V operation, 400 kHz bus speed, 5.5 V tolerant I2C I/O, and mixed-mode signal support. The active-high repeater-enable input allows the device to be placed into a controlled operating state in designs that require bus segmentation or repeatable startup behavior. Open-drain I/O preserves the wired-AND nature of I2C while allowing the repeater to participate in normal clock and data signaling. The device contains two identical bidirectional open-drain buffer circuits intended for I2C and SMBus systems. Its BiCMOS implementation combines CMOS logic with bipolar output characteristics, supporting mixed-mode signal operation while maintaining compatibility with the electrical conventions used by I2C-compatible peripherals. The buffered channels are intended to improve signal integrity when capacitance, wiring distance, or multiple bus branches create excessive loading on a host bus segment. Typical applications include extending an I2C bus between a microcontroller and remote sensors, isolating a high-capacitance section of a bus, separating power domains with compatible logic levels, and preserving signal quality in industrial, embedded, and consumer electronics. The PCA9515APWT is most appropriate when the system uses a 400 kHz or lower I2C-compatible bus and requires two bidirectional repeater channels rather than a unidirectional level translator. Designers should check the device enable state, supply decoupling, pull-up resistor placement, and the voltage tolerance of every connected I2C peripheral before deployment. Pull-ups must be placed on the correct bus segment and sized for its voltage, capacitance, sink current, and speed. The TSSOP footprint also requires adequate copper area and thermal planning even though the device is intended for low-power bus management. This product page combines the manufacturer specification, package information, sourcing links, interface guidance, and practical bus-conditioning considerations. It is intended to help engineers identify whether the PCA9515APWT matches the required channel count, supply range, bus speed, and TSSOP footprint before placing it into an I2C or SMBus design.
PCA9515D - 2-Channel 400 kHz I2C Bus Repeater | NXP
NXP PCA9515D is a 2-channel I2C-bus and SMBus repeater designed to extend a serial bus by buffering the clock and data conductors. The device supports operation up to 400 kHz, provides separate upstream and downstream SDA and SCL paths, and enables two 400 pF bus segments. It is packaged in an 8-pin SOIC surface-mount package. The NXP product page identifies the PCA9515D as no longer manufactured. An I2C bus repeater is a signal-conditioning interface used when cable length, bus capacitance, loading, or voltage differences prevent a controller from reliably driving a distant I2C target. In the broader hierarchy, the PCA9515D is an I2C interface repeater within the I2C interface IC category. It allows a master to communicate through one buffered bus segment while isolating that segment from the electrical loading of another segment. The principal feature is bidirectional buffering of both I2C clock and data lines. According to the NXP manufacturer datasheet, each supported bus arrangement accommodates 400 pF, while the operating frequency reaches 400 kHz. Bidirectional operation permits the controller to address devices on either side of the repeater without changing the I2C protocol. A standard-mode-capable architecture is useful for industrial control, sensor networks, embedded systems, and legacy peripheral expansion where greater speed is unnecessary. Technically, the PCA9515D is a BiCMOS integrated circuit intended for I2C-bus and SMBus systems. BiCMOS construction combines bipolar and CMOS transistor functions, supporting the interface's bidirectional signal path while maintaining low-power operation. Its two-channel arrangement provides one input-side and one output-side connection for SDA and SCL, creating a controlled separation between bus segments rather than simply adding another capacitive load. Typical uses include extending a controller connection to remote sensors, isolating a high-load I2C segment, and linking two PCB zones that require separate routing or bus termination. It can also support SMBus-style management buses operating at compatible standard-mode rates. The principal design constraint is ensuring that every side of the repeater remains within its allowed capacitance and that pull-up resistors suit the local voltage and current requirements. For implementation, place the repeater between the two bus sections and connect the downstream SDA and SCL conductors to the corresponding buffer pins. Provide the supply decoupling recommended by the manufacturer datasheet, and confirm that pull-up resistor values account for the separate cable capacitance of both bus segments. Review the enable behavior and bus contention conditions before using the device in a design that requires hot-plug behavior. This product page combines the manufacturer lifecycle status, bus-function details, package information, sourcing guidance, and engineering-focused replacement analysis. It also identifies the limits of the available drop-in alternatives, helping designers distinguish electrically equivalent order variants from true pin-compatible replacements before modifying an existing PCB.
PCA9516APW - 5-Channel 400kHz I2C Bus Hub | NXP
The NXP Semiconductors PCA9516APW is a 5-channel bidirectional I2C-bus and SMBus hub rated for operation up to 400 kHz, with open-drain input/outputs and individual active-HIGH repeater enables in a 16-pin TSSOP package. It extends an I2C bus by buffering both clock and data lines, allowing five downstream buses with up to 400 pF each. An I2C bus hub is an interface IC that regenerates and buffers SDA and SCL signals between a controller and multiple bus segments. In the product hierarchy, a bus hub is a type of I2C interface controller, interface IC, and semiconductor. This buffering approach reduces the loading presented to the upstream controller, separates downstream capacitive loads, and permits cable or board-distance extension where the original I2C bus would otherwise exceed its capacitance limit. Key features include five bidirectional repeater channels, active-HIGH individual repeater enable inputs, lock-up-free operation, support for arbitration and clock stretching across the repeater, and powered-off high-impedance I2C pins. The device accommodates Standard-mode and Fast-mode I2C devices and multiple controllers. Its operating supply range is identified by NXP as beginning at 2.3 V, while the available search results specifically describe 2.5 V and 3.3 V support. Each downstream segment can accommodate up to 400 pF. This is important because I2C uses open-drain signaling, and capacitance on SDA and SCL raises rise time and can cause timing failures. The PCA9516A architecture isolates each buffered bus segment, allowing unused channels to be disabled independently. Its powered-off high-impedance behavior helps avoid unwanted bus contention during shutdown or partial power-down conditions. Typical uses include extending sensor and EEPROM networks, isolating industrial control modules, supporting SMBus systems, and distributing clock and data to separate I2C branches. The hub is especially useful when multiple relatively slow devices create substantial bus capacitance or when a PCB layout requires electrical separation between controller and peripheral buses. Designers should connect pull-up resistors to each bus segment and place them in accordance with the bus voltage, capacitance, and rise-time requirements. Trace lengths, connector capacitance, and leakage current must be included in the worst-case electrical assessment. Disabled channels should not be assumed to provide isolation unless the enable state and powered-off pin behavior are verified for the operating condition. This page combines verified manufacturer and distributor information with practical bus-extension guidance, pricing context, package details, and replacement analysis. It is intended to help engineers determine whether a five-channel buffered hub is appropriate before committing a board design to the TSSOP-16 footprint.
PCA9517D - 2-Channel 400kHz I2C Level Translator | Texas Instruments
The Texas Instruments PCA9517D is a two-channel bidirectional I2C and SMBus buffer/repeater operating up to 400kHz, with a supply voltage range of 2.7V to 5.5V and an 8-pin SOIC package. It provides voltage-level translation between low-voltage and higher-voltage bus domains and includes independent enable control for each side. What is a level-translating I2C buffer/repeater? It is an interface IC that connects two bidirectional serial buses operating at different voltage levels. The PCA9517D belongs to the I2C repeater and voltage-level-translator hierarchy, within interface ICs and semiconductors. Its two channels isolate bus voltage domains while preserving bidirectional data transfer, helping systems separate voltage levels without redesigning the upstream and downstream devices. Key verified features include two bidirectional channels, 400kHz operation, and compatibility with I2C and SMBus applications. The device can translate signals between low-voltage domains, including voltages down to 0.9V in the NXP-described PCA9517 function, and higher-voltage domains from 2.7V to 5.5V. The 8-SOIC package supports conventional surface-mount assembly and is identified by Texas Instruments as a two-channel signal buffer/repeater. The PCA9517D is useful when two I2C domains require different voltage ranges or when a bus segment needs buffering. Its two independent enables allow unused channels to be disabled, while the bidirectional architecture supports data flow in either direction. The verified distributor listing specifies 400kHz operation and an 8-SOIC package; detailed electrical limits should be confirmed against the manufacturer datasheet before production release. Typical applications include voltage-level translation between low-voltage sensors and higher-voltage controllers, SMBus isolation between subsystems, interface conditioning between PCB domains, and embedded systems where I2C devices use different supply rails. Because it is a repeater rather than a regulator, system designers must verify pull-up voltage, bus capacitance, propagation delay, and enable sequencing on each side. A key design consideration is that both sides of each channel must be properly referenced and pulled up for the voltage domains being supported. Do not assume that level translation removes the need for correct pull-up placement or timing review. Confirm the exact pinout, enable polarity, maximum loading, and operating limits from the official Texas Instruments documentation. This page combines verified distributor information, manufacturer product identity, interface-function context, package information, and practical selection guidance to support engineers searching for a PCA9517D replacement, equivalent, pinout, price, or I2C level-translation solution.
PCA9517DG4 - 2-Channel 400kHz I2C Level Translator | Texas Instruments
Texas Instruments PCA9517DG4 is a 2-channel bidirectional I2C bus and SMBus level-translating buffer/repeater operating up to 400 kHz, with low-side operation down to 0.9 V and high-side operation from 2.7 V to 5.5 V, in an 8-pin SOIC package. The device separates SDA and SCL buses into low-voltage and high-voltage domains so controllers and peripherals using different logic levels can communicate without direct logic-level incompatibility. An I2C level translator, also called a voltage-level translator, is an interface IC placed between two bidirectional open-drain buses. The PCA9517 belongs to the I2C buffer/repeater hierarchy, where it combines bidirectional buffering, voltage-level translation, and bus-segmentation functions. Its two-channel architecture allows SDA and SCL to cross independently between a low-voltage domain and a higher-voltage domain while preserving I2C clock stretching and SMBus-compatible operation. Key features include two bidirectional channels, operation from 0.9 V on the low side to 5.5 V on the high side, a maximum I2C bus speed of 400 kHz, and compatibility with both I2C and SMBus systems. The buffered channels can extend usable bus reach by isolating capacitance accumulated on the source side from the destination side. A quoted propagation delay of 170 ns and input capacitance of 6 pF are important when selecting pull-up resistors and evaluating timing margins. The PCA9517 uses bidirectional buffers rather than unidirectional voltage-level shifters. Because I2C and SMBus signals are open-drain and pulled up externally, each translated channel can conduct in either direction. This makes the device suitable for a host controller operating at a lower voltage communicating with sensors, memory devices, or expansion components whose pull-up network uses a higher supply voltage. The manufacturer describes the PCA9517 as a CMOS and BiCMOS integrated circuit for these applications. Typical uses include voltage adaptation between 1.8 V, 2.5 V, 3.3 V, and 5 V logic domains; isolating a long or heavily loaded I2C branch; and extending communication between a microcontroller and higher-voltage sensors or EEPROMs. Because both SDA and SCL require translation, the complete two-channel arrangement keeps data and clock voltage domains aligned. Designers must provide correct pull-up resistors on each side of the translator and account for the 170 ns propagation delay when calculating the maximum operating frequency. The 8-SOIC package is also used by the PCA9515A, while Texas Instruments' TCA9517 is identified as a comparable dual bidirectional I2C buffer. Review device-specific enable behavior, bus capacitance, and logic thresholds before finalizing a replacement. This page organizes the PCA9517DG4 specifications, replacement candidates, application guidance, and design considerations into one engineering-focused reference. It also distinguishes the published 0.9 V low-side capability from the 2.7 V to 5.5 V high-side range and identifies package and functional differences that matter when reusing an existing PCB.
PCA9517DGKR - 2-Bit 400kHz I2C Level Translator | Texas Instruments
The Texas Instruments PCA9517DGKR is a 2-bit level-translating I2C bus buffer/repeater designed for bidirectional voltage-level translation between low-voltage and higher-voltage logic domains. It supports I2C and SMBus systems operating up to 400 kHz, uses two independently supplied voltage rails, and is housed in an 8-pin VSSOP package. The device is intended for systems in which the I2C bus must cross between different supply-voltage domains while retaining bidirectional communication. An I2C level-translating buffer, also called an I2C bus repeater or bidirectional level translator, is an interface IC that separates two I2C bus segments connected to separate voltage supplies. It allows a low-voltage controller to communicate with a higher-voltage peripheral without violating the input thresholds of either device. In the broader hierarchy, the PCA9517DGKR belongs to the voltage-translator and interface-controller class within interface ICs, rather than acting as a standalone microcomputer or power converter. The PCA9517 family provides two bidirectional channels, allowing the repeater to extend or isolate an I2C or SMBus connection. Its separate low-side and high-side supply pins permit the two sides of the bus to operate at different logic levels. The device is specified for a maximum bus frequency of 400 kHz, making it appropriate for standard-speed I2C systems and SMBus-compatible equipment. Its level-translation function helps reduce voltage-threshold, noise-immunity, and capacitive-loading problems that occur when devices with incompatible supply voltages share the same bus. The device is identified as a BiCMOS integrated circuit intended for I2C bus and SMBus systems. The verified manufacturer product page describes it as a 2-bit level-translating 400-kHz I2C/SMBus buffer/repeater. Because the sides are independently powered, the translator can accommodate logic-domain differences that are commonly encountered between low-voltage sensors, embedded processors, EEPROMs, and higher-voltage interface peripherals. The translator does not change the serial data format and does not increase the protocol's maximum clock rate beyond its specified 400-kHz capability. Typical uses include voltage isolation between a low-voltage microcontroller and a higher-voltage sensor bus, extending an I2C connection into a separate voltage domain, and interfacing peripheral groups that require different supply rails. The device can also be used in industrial equipment, portable electronics, instrumentation, and communication modules where a robust I2C bus segmentation strategy is preferred over directly tying incompatible logic levels together. System designers should account for bus capacitance, pull-up resistor placement, supply sequencing, and the operating limits of both connected bus domains. PCA9517DGKR is packaged in the compact 8-pin VSSOP form identified by the TI ordering code DGKR. The DGK package is intended for surface-mount assembly and supports compact PCB layouts. The key design tradeoff is that level translation adds a buffer and separate supply domains, so the design must preserve correct pull-up placement and ensure that both supplies remain within the limits specified for the device. The TI comparison materials identify TCA9517 as a related device with application and datasheet guidance that should be reviewed when selecting a replacement or new-design alternative. This page organizes the manufacturer product information, package identity, source links, technical use cases, and drop-in replacement findings for PCA9517DGKR. It emphasizes verified interface characteristics rather than treating every similarly packaged translator as automatically interchangeable, because enable behavior, electrical limits, pin functions, and bus-direction assumptions can differ between devices.
PCA9517DR - 2-Channel 400kHz I2C Level Translator | Texas Instruments (Tape & Reel)
The Texas Instruments PCA9517DR is a two-channel bidirectional I2C and SMBus buffer/repeater operating up to 400kHz, with a supply voltage range of 2.7V to 5.5V and an 8-pin SOIC package. It provides voltage-level translation between low-voltage and higher-voltage bus domains and includes independent enable control for each side. What is a level-translating I2C buffer/repeater? It is an interface IC that connects two bidirectional serial buses operating at different voltage levels. The PCA9517DR belongs to the I2C repeater and voltage-level-translator hierarchy, within interface ICs and semiconductors. Its two channels isolate bus voltage domains while preserving bidirectional data transfer, helping systems separate voltage levels without redesigning the upstream and downstream devices. Key verified features include two bidirectional channels, 400kHz operation, and compatibility with I2C and SMBus applications. The device can translate signals between low-voltage domains, including voltages down to 0.9V in the NXP-described PCA9517 function, and higher-voltage domains from 2.7V to 5.5V. The 8-SOIC package supports conventional surface-mount assembly and is identified by Texas Instruments as a two-channel signal buffer/repeater. The PCA9517DR is useful when two I2C domains require different voltage ranges or when a bus segment needs buffering. Its two independent enables allow unused channels to be disabled, while the bidirectional architecture supports data flow in either direction. The verified distributor listing specifies 400kHz operation and an 8-SOIC package; detailed electrical limits should be confirmed against the manufacturer datasheet before production release. Typical applications include voltage-level translation between low-voltage sensors and higher-voltage controllers, SMBus isolation between subsystems, interface conditioning between PCB domains, and embedded systems where I2C devices use different supply rails. Because it is a repeater rather than a regulator, system designers must verify pull-up voltage, bus capacitance, propagation delay, and enable sequencing on each side. A key design consideration is that both sides of each channel must be properly referenced and pulled up for the voltage domains being supported. Do not assume that level translation removes the need for correct pull-up placement or timing review. Confirm the exact pinout, enable polarity, maximum loading, and operating limits from the official Texas Instruments documentation. This page combines verified distributor information, manufacturer product identity, interface-function context, package information, and practical selection guidance to support engineers searching for a PCA9517DR replacement, equivalent, pinout, price, or I2C level-translation solution.
PCA9517DRG4 - 2-Channel 400kHz I2C Buffer | Texas Instruments
The Texas Instruments PCA9517DRG4 is a 2-channel, bidirectional I2C/SMBus level-translating buffer operating up to 400 kHz in an 8-pin SOIC package. It buffers both SDA and SCL, supports a 2.7 V to 5.5 V operating supply, and can connect two I2C buses with up to 400 pF of bus capacitance each. The device is intended for voltage translation, capacitance extension, and isolation between bus segments. A level-translating I2C buffer is an interface IC positioned within the hierarchy of I2C interface devices, bus repeaters, and semiconductor signal-conditioning components. It sits between a controller or peripheral and a remote I2C segment, reproducing each logic transition in the appropriate voltage domain. Unlike a unilateral digital buffer, the PCA9517 supports bidirectional signal flow, allowing SDA and SCL traffic to travel in either direction without changing the bus wiring. The principal features are two independently buffered channels, a maximum signaling rate of 400 kHz, and operation from 2.7 V to 5.5 V. According to the manufacturer datasheet, the device can connect two buses having up to 400 pF of capacitance per bus, making it useful for extending a system beyond the capacitance limit of a direct controller connection. An enable input and reference-voltage structure support controlled bus-segment operation. BiCMOS implementation combines low-voltage BiCMOS logic with bipolar circuitry, providing bidirectional level translation in an 8-pin SOIC package. The buffered architecture isolates capacitive loading on the remote side from the driving controller while preserving standard I2C behavior. The manufacturer datasheet identifies the PCA9517 as a BiCMOS integrated circuit intended for I2C bus and SMBus systems. Typical uses include separating a main controller from a high-capacitance sensor bus, isolating noisy or slow-changing peripheral groups, and supporting mixed-voltage I2C segments. It is also appropriate when a cable-connected module requires buffering to improve signal integrity, provided the complete circuit remains within the specified capacitance, voltage, and frequency limits. For layout, keep SCL and SCL2 routing short and maintain continuous ground return paths between the buffered sections. Place the device where both bus branches remain electrically short, and validate the remote branch for the datasheet capacitance limit rather than relying on the 400 kHz rating alone. Confirm enable-state behavior during power-up and shutdown before releasing the downstream bus. This page organizes the PCA9517DRG4 electrical characteristics, package details, pin assignment, verified sourcing references, drop-in alternatives, and application guidance. It also highlights practical differences among same-footprint options so engineers can select a replacement without overlooking enable behavior, voltage range, or channel configuration.