Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
SN65HVD96D - 5 Mbps SymPol Transceiver | Texas Instruments
The Texas Instruments SN65HVD96D is a half-duplex, 1/1 SymPol transceiver operating from a single 5 V supply in an 8-pin SOIC package. It supports signaling up to 5 Mbps, communicates reliably on normal or reversed-wire bus lines, and uses a symmetric-polarity receiver with 100 mV hysteresis. These characteristics make it suitable for industrial point-to-point, multi-drop, and multi-point communication networks. A SymPol transceiver is a physically robust bus interface integrated circuit that combines a differential driver and differential receiver into one package. It belongs to the interface IC hierarchy, alongside RS-485 transceivers, but uses symmetric polarity rather than the conventional RS-485 differential signaling convention. The SN65HVD96 series is an upgrade path for RS-485 installations, although the devices are not protocol-compatible with existing RS-485 networks. Key electrical features include a 4.75 V to 5.25 V supply range, one transmitter and one receiver, 5 Mbps signaling, 100 mV receiver hysteresis, and support for reversed-wire connections. The symmetric-polarity receiver helps the device interpret bus states consistently when conductors are connected in reverse. The 8-pin SOIC package also saves board area compared with equivalent discrete driver and receiver implementations. TI specifies an industrial operating range from -40 °C to 85 °C, making the device suitable for industrial instrumentation, factory automation, and commercial equipment that operates outside extended automotive temperature limits. The SOIC outline supports conventional surface-mount assembly, while the eight-pin footprint reduces the number of components needed to implement a robust bus node. Typical uses include industrial sensor networks, process-control equipment, remote monitoring stations, PLC peripheral interfaces, and point-to-point data links between controllers and field devices. Because the SN65HVD96D supports reversed wiring and 5 Mbps signaling, it is particularly useful where field installation errors or shorter, higher-speed interconnects are expected. The device pinout is identical to the industry-standard SN75176 transceiver, allowing an SN75176-based board to be considered for a SymPol migration. Existing RS-485 firmware and system behavior are not automatically compatible because SymPol is not backward compatible with RS-485, so the bus protocol and termination strategy must be reviewed before replacement. This page consolidates verified manufacturer and distributor information, package and pinout details, application guidance, and migration considerations that are not presented together on a standard distributor listing. Pricing and drop-in replacement availability are reported only where supported by verified source data.
SN65LBC176DR - 10Mbps RS-485 Transceiver 5V | Texas Instruments
The Texas Instruments SN65LBC176DR is a differential bus transceiver combining a 3-state differential line driver and a differential input line receiver, both operating from a single 5V supply, in an 8-pin SOIC (D) package rated from -40C to +85C. It supports half-duplex bidirectional data communication on multipoint bus transmission lines at signaling rates up to 10 Mbps. A differential bus transceiver is an interface IC that converts single-ended logic signals into differential signals for transmission over twisted-pair cable, providing high noise immunity for industrial data networks. The SN65LBC176 belongs to the RS-485/RS-422 transceiver family within the broader hierarchy of interface ICs and line drivers, and it meets or exceeds the requirements of ANSI TIA/EIA-485 (RS-485) and ISO 8482:1987 (E). Key features include a driver enable (DE, active-high) and receiver enable (RE, active-low) that can be tied together to form a single direction-control pin, low-skew LinBiCMOS technology designed for high-speed serial and parallel data transmission, and bus fault protection across a -10V to +15V common-mode range. The driver outputs differential signals on pins A and B while the receiver accepts differential input, allowing direct connection to the multipoint bus. One driver and one receiver per device simplify point-to-point and multidrop network nodes. The LinBiCMOS process yields low power consumption with high output drive, supporting bus loading of up to 32 unit loads and cable lengths of several thousand feet at lower data rates. Typical applications include industrial automation networks, motor-drive communication links, building automation, energy metering, and any half-duplex RS-485 fieldbus requiring 10 Mbps throughput. Design tip: bias the bus with fail-safe resistor dividers (typically 560 ohm to the A-line pull-down and B-line pull-up) and terminate both bus ends with 120 ohm to prevent reflections and ensure a defined receiver state when all drivers are disabled.
SN65LVDS31D - 400 Mbps Quad LVDS Driver | Texas Instruments
The Texas Instruments SN65LVDS31D is a 400-Mbps low-voltage differential signaling (LVDS) quad high-speed differential driver with four independent driver outputs, a 3.3 V supply, and a 16-pin SOIC package. According to the manufacturer product data, it meets or exceeds ANSI TIA/EIA-644 requirements and provides a typical differential output voltage of 350 mV into a 100-ohm load. An LVDS differential line driver is a high-speed interface IC that converts CMOS or LVTTL inputs into low-voltage differential outputs. In the broader hierarchy, an LVDS driver belongs to differential line-driver ICs, interface ICs, and semiconductors. Its differential signaling reduces common-mode noise sensitivity and supports reliable point-to-point data transmission over balanced interconnects. Key features include four drivers in one package, operation from a 3.3 V supply, 400-Mbps signaling capability, typical 1.7 ns propagation delay, and typical output rise and fall times of 500 ps. The manufacturer product page also identifies pin compatibility with AM26LS31, MC3487, and µA9638, enabling board-level substitution where electrical and timing requirements are confirmed. The SN65LVDS31D is intended for high-speed point-to-point links, including display and video backplanes, industrial control links, communications equipment, and test systems. Differential outputs help maintain signal integrity when the source and destination are connected through controlled-impedance traces or a suitable cable. When designing around this device, use the manufacturer’s recommended termination and layout practices. Confirm trace impedance, keep the differential pair routed with matched geometry, provide adequate bypassing near the supply pins, and verify receiver, cable, and connector characteristics. The supplied data confirms -40°C to +85°C operation for the SOIC-16 device, while other electrical limits should be taken directly from the manufacturer datasheet. This page combines the verified manufacturer identification, distributor listing, pricing reference, interface context, and engineering-focused application guidance. It is intended to help engineers identify the correct part, validate compatibility, and plan a robust LVDS interconnect without treating unsupported parameters as guaranteed specifications.
SN65LVDS32D - 400 Mbps Quad LVDS Receiver | Texas Instruments
Texas Instruments SN65LVDS32D is a 400 Mbps quad high-speed differential receiver designed for low-voltage differential signaling (LVDS), supplied from a single 3.3 V supply and housed in a 16-pin SOIC package. It provides four differential receiver channels, differential input thresholds of 100 mV maximum, typical propagation delay of 2.1 ns, and typical power dissipation of 60 mW. The receiver is intended for systems requiring reliable high-speed differential input reception under industrial and automotive-qualified conditions. An LVDS receiver is an interface circuit that converts a small differential voltage across a balanced pair into a digital logic signal. It belongs to the receiver and transceiver interface IC category, within broader communication-interface and signal-conditioning electronics. Differential reception rejects common-mode noise and helps maintain signal integrity across longer interconnects or cables than ordinary single-ended logic receivers. The SN65LVDS32D implements the electrical characteristics associated with ANSI TIA/EIA-644, as identified in the manufacturer product data. Key features include four independent receiver channels, operation from one 3.3 V supply, signaling rates up to 400 Mbps, 100 mV maximum differential input threshold, and open-circuit fail-safe behavior suitable for cold-sparing and redundant systems. The manufacturer product page also identifies pin compatibility with AM26LS32, MC3486, and µA9637. Automotive qualification and ESD protection features make the device relevant to industrial control, communications, test equipment, and vehicle electronics where differential signaling is required. The electrical performance is centered on low-latency differential reception. A typical 2.1 ns propagation delay is useful when the system must preserve timing relationships across multiple channels. The 60 mW typical power dissipation provides a practical baseline for power budgeting, although actual dissipation depends on supply voltage, input activity, output loading, and operating temperature. The single-supply architecture simplifies system power design while requiring correct input common-mode and termination practices. Typical applications include industrial automation links, high-speed data acquisition, point-to-point communications, test and measurement equipment, and automotive or other harsh-environment interfaces. In these systems, the receiver is placed after a balanced transmission line and connected to downstream digital logic through its four differential receiver outputs. Designers should verify the complete channel budget, cable or PCB loss, termination, grounding, and input common-mode range in the system-level design. A key design consideration is preserving the LVDS signal path: use controlled-impedance routing, matched differential pair geometry, appropriate termination, and short return paths to avoid degrading the 400 Mbps target. Do not treat the receiver as a general-purpose comparator or add logic without checking the output timing, supply requirements, and pin-specific electrical limits. This page combines the verified manufacturer and distributor information with practical LVDS design guidance for component selection and implementation.
SN65LVDS93ADGGR - LVDS Serializer 10-135MHz 56-TSSOP | TI
The Texas Instruments SN65LVDS93ADGGR is a FlatLink LVDS serializer (SerDes transmitter) that converts 28 bits of single-ended LVTTL parallel data into 4 LVDS data pairs plus 1 LVDS clock pair, operating over a 10 MHz to 135 MHz input clock range in a 56-pin TSSOP (DGG) package rated from -40C to +85C. An LVDS (Low-Voltage Differential Signaling) serializer is an interface IC that compresses a wide parallel data bus onto a small number of high-speed differential pairs, dramatically reducing connector size, cable count, and EMI between a host processor and a display or backplane. Within the signal-chain hierarchy, it belongs to the SerDes (serializer/deserializer) family of high-speed interface products, sitting between parallel LVTTL logic and LVDS physical-layer line drivers. Key features of the SN65LVDS93A include 28:4 data channel compression delivering up to 1.904 Gbps serialized throughput per the datasheet, an integrated 7x clock synthesizer that multiplies the input reference clock, and five LVDS line drivers meeting the TIA/EIA-644 LVDS standard for low EMI differential signaling. The A-suffix version extends the supported operating range to 10 MHz - 135 MHz, making it faster than the base SN65LVDS93, which is specified from 20 MHz to 68 MHz on TI.com. Architecturally, the device contains four 7-bit parallel-load serial-out shift registers, the 7x PLL clock synthesizer, and five LVDS drivers in a single IC. Data is latched on the parallel clock, shifted out at 7x rate, and transmitted with the embedded clock pair so a matching deserializer such as the SN65LVDS96 or DS90CF384 can recover timing without a separate clock channel. LVDS current-mode drivers on a 3.3V supply produce approximately 350 mV differential swings with low skew. Typical applications include TFT-LCD panel interfacing in industrial displays and medical monitors, video transmission between a graphics controller and a FlatLink-compatible display, and point-to-point board-to-board links where a 28-bit parallel bus must cross a flex cable or backplane with minimal wiring. When designing with this device, keep the parallel input setup/hold times within datasheet limits and route the LVDS pairs as controlled-impedance 100-ohm differential traces; also confirm the exact input clock range against your system, since TI lists both a 10-135 MHz range (A version) and 20-68 MHz (base part) across product pages. This page synthesizes distributor inventory data, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet alone, with pricing refreshed as of 2026-10-19.
SN65LVDT100DGK - 2Gbps LVDS Repeater/Translator | Texas Instruments
The Texas Instruments SN65LVDT100DGK is a 2-Gbps LVDS, LVPECL and CML to LVDS repeater/translator in an 8-pin VSSOP (DGK) package. It accepts low-voltage differential signaling (LVDS), positive-emitter-coupled logic (PECL), or current-mode logic (CML) input signals at signaling rates up to 2 Gbps and regenerates them as clean LVDS output levels, operating from a single 3 V to 3.6 V supply. A differential repeater/translator is an interface IC that sits in a high-speed serial signal path, receiving a degraded or logic-incompatible differential signal and re-driving it with fresh, standard-compliant output levels. Within the signal-chain hierarchy, it belongs to the buffer/repeater family of interface ICs, bridging logic families (LVDS, LVPECL, CML) that would otherwise require discrete level-shifting networks and termination circuitry. Key features include a maximum total jitter of 100 ps, low part-to-part skew, and receiver input threshold hysteresis of tens of millivolts for noise immunity on marginal input signals. A distinctive advantage is the integrated 110-ohm differential line termination resistor, which shortens stub length, reduces component count, and saves board space compared with discrete 100-ohm termination schemes. TI positions this device as a low-power alternative to the MC100EP16 ECL repeater. Architecturally, the receiver front-end accepts a wide-range differential input (LVDS, PECL, or CML swings) and drives a current-mode LVDS output stage designed for 100-ohm differential transmission lines. The short signal path through the device (analog repeat, no FIFO or retiming logic) keeps propagation delay low, and TI's Bipolar/high-speed process supports multi-gigabit signaling while remaining within a modest supply-current budget at 3.3 V. Typical applications include backplane and point-to-point LVDS link conditioning, clock distribution and repeating in telecom and networking equipment, and extending LVDS display or camera links where cable losses degrade eye diagrams. Where a PECL output is required instead of LVDS, the companion SN65LVDS100/SN65LVDT101 family members cover that case in related packages. Design consideration: keep the input traces to the integrated termination as short as possible; the device must receive a differential signal that crosses its threshold window with hysteresis, so check eye margins at 2 Gbps with your actual channel loss before committing to layout. This page synthesizes distributor availability data, TI family cross-references, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet alone. Pricing shown is as of 2026-10-19 and is an estimate pending live distributor verification.
SN65MLVD200ADR - Half-Duplex M-LVDS Transceiver, 8-SOIC | TI
The Texas Instruments SN65MLVD200ADR is a half-duplex Multipoint-LVDS (M-LVDS) transceiver in an 8-pin SOIC package, with one driver and one receiver sharing a single differential bus pair. It conforms to the M-LVDS standard (TIA/EIA-899) and supports data rates up to 100 Mbps (200 Mbps in some drive modes) with low 700 ps driver output skew, making it suitable for high-speed multipoint backplane and clock-distribution links. The IC operates from a single 3.3 V supply and provides 24 mA of drive current on the M-LVDS bus pins, with internal fail-safe biasing on the receiver inputs. Background: An LVDS (Low-Voltage Differential Signaling) transceiver is a type of high-speed differential interface IC that transmits data across a balanced pair of wires using low-swing, current-mode signaling, achieving high noise immunity at low power. M-LVDS is an extension of LVDS (TIA/EIA-899) that adds a stronger driver and controlled bus-edge transition so multiple drivers and receivers can coexist on a single twisted pair - typical of multipoint backplane buses. Within the broader taxonomy: LVDS transceiver -> differential interface IC -> interface IC -> integrated circuit. Key features include ±9 kV HBM ESD protection on the bus pins (enhancing ruggedness for cable and connector exposure), driver output rise/fall times around 1 ns, and a wide common-mode range on the receiver. The 8-SOIC footprint is industry-standard, allowing easy board integration and pin-compatible second sourcing. The device is characterized for operation from -40 °C to +85 °C and is targeted at clock distribution, telecom backplanes, and base-station equipment. Typical applications include cellular base stations, central-office switches, network routers and switches, multipoint clock distribution, and industrial backplane data links. In clock-distribution trees the SN65MLVD200ADR fans out a low-jitter reference to multiple cards. Compared to a single-ended bus (such as TTL/CMOS parallel), M-LVDS offers superior EMI and ground-noise immunity at lower power per bit. Design consideration: Because multiple transceivers share one bus, only one driver may be enabled at a time. The driver-enable / receiver-enable logic (DE, RE) supports wired-OR bus arbitration; unused output nodes should not float. Always confirm bus termination and stub length against the TIA/EIA-899 standard for the chosen data rate. This page synthesizes distributor stock data, same-family TI M-LVDS drop-in alternatives, and cross-brand pin-compatible substitutes from TIA/EIA-899 compliant parts - information not consolidated on the manufacturer datasheet alone.
SN74AUP1T34DCKR - 1-Bit Level Translator 0.9-3.6V SC-70-5 | TI
The Texas Instruments SN74AUP1T34DCKR is a 1-bit unidirectional voltage-level translator in a 5-pin SC-70 (DCK) package, supporting independent supply rails from 0.9 V to 3.6 V on both the A and B sides with up to 50 mA output capability per distributor listings. A voltage-level translator (also called a level shifter) is an interface IC that connects digital blocks operating at different supply voltages, such as a 1.8 V microcontroller GPIO driving a 3.3 V peripheral. Level translators belong to the interface IC family within the broader semiconductor hierarchy, sitting alongside bus switches, transceivers, and logic buffers. The SN74AUP1T34 is a fixed-direction, non-inverting single-channel device built on TI's Advanced Ultra-Low Power (AUP) process family. Key features include two separately configurable power rails (VCCA and VCCB can each be anywhere from 0.9 V to 3.6 V in any order), making it suitable for asymmetric translation such as 1.2 V to 3.3 V or 2.5 V to 1.8 V. The AUP architecture delivers very low dynamic power consumption and low static supply current, important for battery-powered and always-on designs. The device supports partial power-down operation via Ioff circuitry, so inputs and outputs remain high-impedance when either rail is unpowered, protecting downstream circuits during multi-rail sequencing. Technically, the translator combines a low-voltage input stage referenced to VCCA with a push-pull output stage referenced to VCCB, reproducing the input logic level on the output with correct CMOS levels on the destination rail. Because the direction is fixed (A to B) and the logic is non-inverting, it behaves like a buffer across domains and requires no direction-control pin, simplifying board design compared with bidirectional translators such as the TXB/TXS families. Typical applications include I2C-adjacent GPIO translation, UART and SPI signal buffering between voltage domains, enable/flag signal shifting in power-management circuits, and level adaptation in portable, wearable, and IoT boards where 1.2 V, 1.8 V, 2.5 V, and 3.3 V rails coexist. Design tip: keep both rails within 0.9 V to 3.6 V at all times and place 0.1 uF decoupling capacitors close to both VCCA and VCCB pins; note the SC-70-5 footprint is compact, so thermal and layout effort is minimal but probe access is limited. This page adds value beyond the TI datasheet by combining drop-in alternative cross-references, application guidance, and pricing comparison in one place.
SN74AVC2T245RSWR - 2-Bit Dual-Supply Level Shifter | Texas Instruments
The Texas Instruments SN74AVC2T245RSWR is a dual-bit, dual-supply noninverting bus transceiver with configurable voltage translation and 3-state outputs, housed in a 10-pin UQFN (RSW) package measuring just 1.8 mm x 1.4 mm. It operates from two independent supply rails (VCCA and VCCB) of 1.2 V to 3.6 V, enabling bidirectional logic-level translation between any two voltage domains. A dual-supply bus transceiver is a logic device that transfers data bidirectionally between two ICs operating at different logic levels, such as a 1.8 V microcontroller and a 3.3 V peripheral. It belongs to the broader hierarchy of voltage translators within interface logic ICs, and the SN74AVC2T245 is a member of TI's AVC (Advanced Very-low-voltage CMOS) family, optimized for high speed and low static power. Key features include independent direction control for each channel (DIR1 and DIR2), an output-enable (OE) pin for 3-state bus isolation, and a VCC isolation feature that forces all I/O ports to high impedance when either supply is at GND. The device achieves data rates up to 380 Mbps with a typical propagation delay of 2.4 ns and delivers 12 mA output drive at 3.3 V. The AVC architecture uses configurable level shifting: output levels are set automatically by VCCA and VCCB with no direction-strapping constraints. Ioff circuitry supports partial power-down operation by blocking backflow current when either rail collapses, and quiescent current is approximately 20 uA for battery-friendly designs. Typical applications include level shifting for I2C, SPI, UART, and GPIO buses in personal electronics, industrial control, and networking equipment. The 1.8 mm x 1.4 mm UQFN footprint suits space-constrained portable and wearable designs. Design consideration: keep both supplies within 1.2 V to 3.6 V at all times, and use the OE pin with a pull-down so the bus stays tri-stated during power-up to avoid contention.
SN74AVC4T245PWR - 4-Bit Dual-Supply Level Shifter | TI
The Texas Instruments SN74AVC4T245PWR is a 4-bit dual-supply bus transceiver with configurable voltage translation and 3-state outputs, supplied in a 16-pin TSSOP (PW) package. It operates from two independent supply rails, VCCA and VCCB, each ranging from 0.8V to 3.6V, enabling bidirectional level shifting between mixed voltage domains such as 1.2V, 1.5V, 1.8V, 2.5V, and 3.3V. A bus transceiver is a digital integrated circuit that transfers data bidirectionally between two buses, using direction-control and output-enable inputs plus 3-state outputs so multiple devices can share a common bus. The SN74AVC4T245 belongs to the voltage translator (level shifter) family within the broader logic IC and interface IC hierarchy, and it is essential in mixed-voltage systems where MCUs, FPGAs, sensors, and memory operate at different logic levels. Key features include configurable voltage translation on both ports, control inputs (1DIR, 2DIR, 1OE, 2OE) referenced to VCCA for simplified control logic, and Ioff partial-power-down circuitry that disables outputs and prevents damaging backflow current when either rail is at GND. A VCC isolation feature places all I/O in high-impedance if either supply is absent. Technically, the device supports asynchronous communication between two data buses at data rates up to 380 Mbps with a typical propagation delay around 2.5 ns, suiting high-speed SPI, parallel bus, and GPIO interfaces. The TSSOP-16 package has a 4.4mm body width and 0.65mm pin pitch for space-constrained PCBs. Typical applications include level shifting for SPI, UART, I2C-adjacent GPIO expansion, and FPGA or ASIC interconnects in industrial control, portable battery-powered electronics, and automotive modules where multiple voltage domains coexist. Design tip: keep the DIR and OE pins driven from VCCA-domain logic and place 0.1uF decoupling capacitors close to both VCCA and VCCB pins; avoid bus contention by sequencing direction changes with a brief high-impedance interval. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
SN74LS242N - Quad Inverting Bus Transceiver | Motorola
The Motorola SN74LS242N is a quad inverting bus transceiver with four 3-state outputs in a 14-pin PDIP package. It is designed for four-line asynchronous, two-way data communication between buses and supports one transceiver element per 4-bit group. The inverting outputs allow the same interface device to provide active-low signaling and bus-driver behavior. A bus transceiver is an interface IC that combines driver and receiver functions on a bidirectional data line. In the broader hierarchy, it belongs to the 74LS logic family, within TTL-compatible digital logic, interface ICs, and semiconductor signal-conditioning products. A quad transceiver can connect two buses through four controlled data paths, with enable control determining whether the outputs actively drive a bus or enter a high-impedance state. The SN74LS242N provides a 4-channel, 4-bit-per-element, inverting, 3-state transceiver configuration. Each channel supports a two-way bus connection, and the three-state output capability allows multiple devices to share a bus when their drivers are disabled. Its 14-pin PDIP package is suitable for conventional through-hole assembly rather than high-density surface-mount designs. The SN74LS242N belongs to the SN54/74LS242 function family, whose original application was asynchronous two-way communication between data buses. Unlike the SN74LS243 family member, the SN74LS242 uses inverting output behavior. This distinction must be checked carefully in bidirectional links because reversing the logic polarity can affect receiver sampling, bus arbitration, and system-level timing. Typical uses include instrumentation buses, embedded control interfaces, legacy computer peripherals, test systems, and industrial data links that require four inverting three-state channels. The part is particularly relevant when preserving an existing 74LS-compatible board requires the original inverting transceiver function and the original 14-pin physical footprint. For PCB integration, maintain the pin assignments shown in the manufacturer datasheet and provide adequate bypass and signal-return routing. Because the device is designed for three-state bus operation, verify both enable timing and output polarity before replacing it with a non-inverting family member. A transceiver with a different output logic function is not a functional drop-in substitute even when the package has the same pin count. This product record combines the device identity, package information, public documentation links, sourced pricing references, and drop-in-replacement screening into an engineering-focused guide. It also distinguishes true pin-compatible choices from nearby 74LS bus devices whose enable arrangement or inversion differs, helping designers avoid a mechanically similar but electrically incompatible replacement.
SN74LS243D - 4-Bit Bus Transceiver | Texas Instruments
The Texas Instruments SN74LS243D is a non-inverting, 4-bit, quad bus transceiver with push-pull output in a 14-pin SOIC package. The device provides four transceiver elements, operates from a 5 V supply, and supports two-way asynchronous communication between data buses. It is designed for terminated lines down to 133 ohms. A bus transceiver is an interface circuit that allows data to move in either direction between a host logic system and an external bus. The quad designation indicates four independently controlled transceiver elements, while the 4-bit designation identifies the parallel data width associated with those elements. Together, these features place the SN74LS243D in the logic IC > interface IC > bus transceiver hierarchy. The SN74LS243D combines four bidirectional transceiver elements with non-inverting push-pull outputs. According to the Texas Instruments product page, the SN74LS243 family can drive terminated lines down to 133 ohms. The SN74LS243 commercial-temperature version is characterized for operation from 0°C to 70°C. Its SOIC-14 package supports conventional surface-mount PCB assembly. The device is intended for asynchronous two-way bus communication, allowing each associated data path to operate as an input or output. Its push-pull output structure is appropriate for digital systems that require defined output levels and balanced drive capability. Because the communication path is bidirectional, system designers must control the transceiver direction through associated interface logic and account for signal timing at both ends of the bus. Typical uses include instrumentation buses, computer peripherals, industrial data exchange, test equipment, and embedded control systems. The 14-pin package simplifies routing compared with larger 8-bit bus transceivers, while the four-element arrangement can cover four data paths when the full bus width is not required. The same organization can also be used in bidirectional buffering arrangements where a host processor communicates with a peripheral over shared conductors. When laying out a board, keep the transceiver near the connector or bus interface, provide a low-impedance ground plane, and place input and output decoupling capacitors close to the supply pins. Check the datasheet pin-description table for the exact direction-control and data-pin assignments before assigning PCB tracks. The 133-ohm line requirement also means that cable or board transmission-line characteristics must be considered rather than treating every connection as an ideal point-to-point link. This product page organizes the manufacturer specifications, source documents, procurement path, and practical replacement considerations into one engineering reference. It also highlights where a design can reuse the 14-SOIC footprint and where a full pin-by-pin comparison remains necessary before substituting a part from another supplier.
SN74LS442N - 4-Bit 3-State Bus Transceiver | Texas Instruments
Texas Instruments SN74LS442N is a quadruple tridirectional bus transceiver packaged in a 20-pin PDIP. The device combines four 4-bit transceiver channels in one package, provides non-inverting signal transfer, and places each bus output in a high-impedance state when its direction control is inactive. This combination makes the SN74LS442N suitable for bidirectional parallel-bus interfaces where connected devices must exchange data while maintaining a shared data path. A bus transceiver is a digital interface component that connects two logic sections through a shared bidirectional line. It belongs to the broader transceiver hierarchy: parallel bus transceiver, bidirectional transceiver, bus-interface IC, and digital logic IC. Unlike a unidirectional buffer, a tridirectional transceiver can support both data transmission and reception. Its 3-state output allows the output driver to disconnect electrically from the bus, preventing multiple connected devices from driving the same node simultaneously. The SN74LS442N organizes four independent 4-bit channels into one 20-pin PDIP package. Each 4-bit section provides parallel data transfer, while the tridirectional architecture supports communication in either direction. The non-inverting implementation preserves the logical relationship between bus data and the corresponding transceiver-side signals. Three-state operation is particularly important for shared buses because it permits an inactive channel to avoid loading the common node. The SN74LS442N belongs to the 74LS low-power Schottky TTL logic family. This family is used in systems that require conventional bipolar TTL-compatible interfacing rather than a modern low-voltage differential bus such as LVDS. Because the SN74LS442N operates as a parallel logic device, board-level design must account for shared-bus contention, direction-control sequencing, adequate signal settling time, and correct handling of every enable and direction input. Typical uses include bidirectional data buffers, computer peripheral interfaces, bus isolation points, test equipment, and legacy industrial control systems. The device can sit between two bus segments when data must be exchanged in both directions without continuously loading either segment. It is also suitable for systems that require a defined high-impedance state during reset, test, or bus ownership changes. The 20-pin PDIP format favors through-hole assembly, repair, and legacy control-system maintenance. For a reliable design, define the ownership of every bus segment so that only one enabled driver sources a given bit at a time. Direction and enable signals should be decoded cleanly and should not leave two transceivers driving simultaneously during transitions. Review signal timing and bus loading against the circuit requirements, and use the manufacturer's pin-description table when assigning PCB tracks. The PDIP footprint also requires adequate board spacing and appropriate lead-forming during insertion. This page combines the device's exact catalog identity, package information, application guidance, qualified same-footprint alternatives, and design-oriented cautions. It focuses on the practical role of four non-inverting 4-bit channels and tri-state bus isolation while directing engineers to the manufacturer datasheet for authoritative electrical limits and timing conditions.
SN74LS645N - 8-Bit 3-State Bus Transceiver | Texas Instruments
Texas Instruments SN74LS645N is an 8-bit, non-inverting, 3-state bus transceiver with a 20-pin PDIP package. It operates from a 4.75 V to 5.25 V supply, supports asynchronous two-way communication between data buses, and includes Schmitt-trigger inputs with a 15 mA sink capability. The device is designed for systems that need to place one side of an eight-bit data path into a high-impedance state so that multiple bus drivers can share a common conductor. An octal bus transceiver is a bidirectional interface IC that combines a bus driver, receiver, and direction-control logic in one package. Within the broader hierarchy of interface ICs, it supports the 74LS bipolar logic family and the TTL-compatible 5 V system environment. Its eight parallel channels make it suitable for routing byte-wide data among processor, memory, peripheral, and backplane interfaces without requiring eight separate single-channel transceivers. The main features include non-inverting data transfer, 3-state output control, eight independently usable I/O paths, and Schmitt-trigger input behavior. The Schmitt trigger helps improve noise tolerance by providing hysteresis at the input threshold. The 3-state output can actively drive a logic high or low, or present a high-impedance state when disabled, allowing several devices to share a bus when only one driver is enabled at a time. The 20-pin PDIP format also supports conventional through-hole assembly and prototyping. Technically, the SN74LS645N combines directional control with bus-state management. Direction and output-enable inputs determine whether data flows from the A-side bus to the B-side bus, from B to A, or remains disabled at the outputs. Because this is a bipolar 74LS-family device, designers should account for the logic levels, transition timing, fanout, and supply tolerances associated with that family rather than treating it as a modern low-voltage CMOS bus device. Typical uses include bidirectional eight-bit CPU and peripheral buses, data multiplexers, test equipment, memory-interface routing, and industrial control boards. In each case, the transmitter is useful where two bus masters or independent subsystems must exchange byte-wide data while retaining tri-state control over bus ownership. The SN74LS645N is most appropriate when legacy 5 V TTL signaling, through-hole construction, and established 74LS interoperability are priorities. During layout, keep the data paths short and route the eight corresponding A and B signals as matched groups. Place decoupling close to the supply pins, provide a common ground reference, and confirm that enable and direction timing does not create contention. This page combines verified product attributes, documented replacement options, and practical bus-interface design guidance for faster component selection.
SN74LVC1G3157DCKR - SPDT Analog Switch, 15Ohm, SC-70-6 | TI
The Texas Instruments SN74LVC1G3157DCKR is a single-channel single-pole double-throw (SPDT) analog switch designed for 1.65V to 5.5V VCC operation, housed in a 6-pin SC-70 (DCK) package. Key parameters include a typical on-state resistance of 15 ohm, a wide 340 MHz bandwidth, and a propagation delay of typically 0.5 ns at 50 pF load, making it suitable for both analog and digital signal routing. An analog switch (also called a bilateral switch or pass gate) is a semiconductor device that uses CMOS transmission gates to connect or isolate two signal paths under logic-level control. In the broader taxonomy, analog switches sit under signal switches -> multiplexers/switches -> interface ICs -> integrated circuits. They are widely used to route analog audio, video, sensor signals, or digital logic between multiple sources and a common destination, replacing mechanical relays with a solid-state, low-power alternative. Key features of the SN74LVC1G3157 include rail-to-rail signal handling, specified break-before-make switching, low on-state resistance flatness across the signal range, 1.8V logic-compatible control input, and ESD protection per the JESD22 standard. The device supports 5V tolerant signal passing even when VCC is only 1.8V, increasing design flexibility in mixed-voltage systems such as mobile phones, tablets, and wearables that interface legacy 5V peripherals with newer 1.8V cores. Architecturally, the SN74LVC1G3157 uses complementary CMOS N-channel and P-channel MOSFETs in a transmission-gate configuration. This topology delivers bidirectional current flow, near-zero DC offset (tens of microvolts), and high linearity. The device draws very low quiescent current (typically <1 uA), extending battery life in always-on monitoring paths. ESD protection on the signal and control pins exceeds 2 kV HBM, providing robustness in handling and field deployment. Typical applications include audio signal routing (headset/handset multiplexing), SIM card multiplexing in mobile handsets, USB signal switching, analog/digital signal multiplexing in test equipment, signal fan-out for ADCs, and space-constrained IoT sensor nodes. The SC-70-6 footprint occupies only 2.0 mm x 1.25 mm of board area, ideal for compact consumer designs. When designing with this device, place ceramic bypass capacitors (0.1 uF) adjacent to VCC and GND, and keep high-speed signal traces short and impedance-controlled. Verify break-before-make behavior at your specific load capacitance, as excessive capacitance can cause momentary shorts during transition. This page synthesizes distributor pricing, drop-in SC-70-6 alternatives, and practical signal-integrity design notes not consolidated in any single manufacturer datasheet.
SN75112D - Dual 2/0 Line Driver | Texas Instruments
The Texas Instruments SN75112D is a dual 2/0 line driver with two independent driver channels, 27 mA output current capability, and a 14-pin SOIC package. Designed for digital-interface transmission, it provides improved output-current regulation across supply-voltage and temperature variations. The manufacturer also identifies high output impedance, a high common-mode output-voltage range, and 10 V TTL-input compatibility as important characteristics for systems that require robust line-driving behavior. A line driver is a digital interface IC that converts a low-voltage logic signal into a stronger output signal suitable for driving a transmission line or connected load. In the broader semiconductor hierarchy, the SN75112D belongs to the interface IC family, where transmitters and drivers condition logic signals for reliable communication between circuit blocks. The SN75112D implements this function as two channels in a single package, allowing one component to service two independent data paths. The device's principal technical feature is its regulated output-current behavior. According to the Texas Instruments product page, the SN75112's higher current of 27 mA permits data transmission over longer lines than lower-current family members. Two channels support economical point-to-point interfaces, while independent operation reduces the need for separate single-channel driver packages. Its 10 V TTL-input compatibility broadens its usefulness in mixed legacy and modern logic environments. Internally, the SN75112D is optimized for constant-current output behavior rather than simple rail-to-rail switching. The manufacturer highlights improved stability over supply-voltage and temperature ranges, high output impedance, and an extended common-mode output-voltage range. These features are particularly relevant when the connected line presents variable loading, long interconnect distances, or noise-prone industrial environments. Exact propagation-delay, supply-voltage, and absolute-maximum limits should be confirmed in the manufacturer datasheet before final circuit release. Typical uses include industrial data links, control interfaces, test equipment, and communications equipment where a transmitter must drive a terminated or capacitively loaded cable. Texas Instruments specifically notes optimum performance with the SN55107A, SN75107A, and SN75108A line receivers. The dual-channel organization also makes the device appropriate for paired control and data paths, provided the receiver and transmitter voltage levels remain compatible. For implementation, verify the supported supply voltage, input logic thresholds, timing limits, and output load capability against the manufacturer datasheet. Place the device close enough to the driven line interface to limit additional trace loading, maintain a continuous return path, and observe the required bypass-capacitor arrangement. Input and output ringing should be evaluated with the actual cable, termination, connector, and receiving-device loading. This product page consolidates the verified manufacturer identity, package information, interface characteristics, related receiver options, and engineering selection criteria. It also separates a true dual line driver from broader transceiver categories and identifies the two same-family line-driver alternatives that can be evaluated for legacy-interface designs.
SN75113N - Dual Differential Line Driver | Texas Instruments
The Texas Instruments SN75113N is a dual differential line driver with two independent differential output channels and three-state output capability, supplied in a 16-pin PDIP package. It operates from a nominal 5 V supply, with the listed operating supply range of 4.75 V to 5.25 V. Each differential output pair can be placed in a high-impedance state, allowing the driver outputs to share a bus when the required output control is inactive. A differential line driver is an interface IC that converts complementary logic signals into a balanced pair of outputs. Differential signaling helps reject common-mode noise, reduces sensitivity to ground offsets, and supports dependable communication over cables or PCB traces where a single-ended driver may be vulnerable to interference. The SN75113 combines two such channels with separate output-pair controls and a common control, providing flexible bus-management options in digital systems. The SN75113 family provides the features associated with the SN75114 line drivers while adding dedicated driver output controls. According to the manufacturer product description, individual controls are available for each output pair, together with a common control for both pairs. When a relevant output control is low, its associated output enters a high-impedance state. This tri-state behavior permits multiple driver sources to be connected to a shared bus when only one source is active at a time. The SN75113N is identified as a 2/0 driver, meaning two driver outputs and no receiver inputs. Its differential output structure is intended for balanced digital interfaces, including point-to-point links, backplanes, test equipment, industrial data acquisition, and older computer peripheral buses. The 16-pin PDIP format also supports through-hole assembly and prototyping workflows, although it occupies more board area than a comparable surface-mount package. Designers should account for the 4.75 V to 5.25 V supply requirement and confirm that the connected logic family uses compatible voltage levels. Output-enable and common-enable logic must be sequenced so that no two enabled drivers contend on the same bus. Signal-integrity work should include controlled-impedance routing, appropriate termination at the receiver, and return-path continuity for the differential pair. SN75113N is suitable when a legacy or industrial system specifically requires a dual differential line driver in a 16-pin PDIP package. For new compact designs, a surface-mount equivalent may reduce board area, but it is not automatically a drop-in replacement because package dimensions, lead geometry, pin functions, and electrical limits must all be reviewed before substitution. This page combines manufacturer product information, distributor identification, package details, replacement guidance, application analysis, and comparison data to support component selection and board-level implementation. It also distinguishes true same-footprint alternatives from related SN75113-family devices that do not provide identical output-control behavior.
SN75114D - Dual Differential Line Driver | Texas Instruments
Texas Instruments SN75114D is a dual differential line driver interface IC designed for digital communication and TTL-compatible signal conditioning. The device operates from a 4.75 V to 5.25 V supply and is specified for a 0 °C to +70 °C commercial temperature range. It is packaged in a 16-pin SOIC package. According to the Texas Instruments product information, the output stages are similar to TTL totem-pole outputs and include sink outputs YS and ZS with corresponding active pullup terminals YP and ZP on adjacent package pins. This arrangement provides a flexible interface for systems that require differential drive, phase splitting, or TTL-compatible expansion. A differential line driver is an interface circuit that converts logic signals into stronger, balanced outputs suitable for driving transmission lines or connecting digital equipment over longer interconnects. SN75114D provides two driver channels in one package, allowing a system designer to drive two related signals while reducing board area and component count. The device can also operate as a TTL expander or phase splitter because its output levels are compatible with TTL logic. The SN75114D is identified as a 2/0 driver, meaning it contains two driver outputs and no corresponding receiver inputs. The 16-pin SOIC package provides a conventional surface-mount footprint and is suitable for industrial control, communications, instrumentation, and legacy computer-interface equipment. Its 5 V supply requirement places it among standard TTL-compatible interface components, allowing it to share a regulated rail with compatible digital logic. The key design consideration is understanding the output-stage architecture. The YS and ZS pins are sink outputs, while YP and ZP provide the corresponding active pullup paths. Board routing should preserve the intended pairing of driver outputs and pullup terminals, and unused inputs or outputs should be handled according to the manufacturer pin descriptions and recommended circuit arrangements. Decoupling and transmission-line routing should follow the datasheet's application guidance to prevent ringing, excessive current, or logic-level errors. Typical uses include differential digital buses, phase-splitting arrangements, TTL logic interfacing, and clock or control-signal distribution where two outputs are required. This product page combines the manufacturer's device description, package information, operating limits, cross-reference results, and practical interface-design guidance for engineers evaluating the SN75114D.
SN75114N - Dual Differential Line Driver, 5 V | Texas Instruments
Texas Instruments SN75114N is a dual differential line driver designed for 5 V systems, with a 16-pin PDIP package and output current rated up to 40 mA. The device generates differential outputs for balanced lines such as twisted-pair interconnects while maintaining TTL-compatible output levels. Its two driver channels provide separate sink outputs and corresponding active pull-up terminals for flexible output configurations. A differential line driver is an interface IC that converts logic-level signals into complementary differential outputs suitable for balanced interconnects. This device belongs to the line-driver hierarchy within interface ICs, where it can drive twisted-pair circuits more effectively than an ordinary single-ended logic output. It also supports applications beyond conventional differential transmission, including TTL expanders and phase splitters. The SN75114N offers two differential driver channels, 5 V operation, TTL-compatible outputs, and a maximum output current of 40 mA per the manufacturer documentation. Sink outputs labeled YS and ZS operate alongside active pull-up terminals labeled YP and ZP on adjacent package pins. This arrangement allows the output stage to be configured according to the signaling requirements and loading of the balanced line. The output architecture resembles a TTL totem-pole output, but the separation of sink and active pull-up terminals provides additional routing flexibility. These terminals can be used independently when the interface requires different drive arrangements. Designers should account for output rise and fall times, propagation delay, and the allowable loading when driving long cables or slow logic inputs. Typical uses include balanced digital data links, differential clock distribution, TTL bus expansion, and phase-splitting circuits. The device is particularly useful when a system needs stronger source current than standard logic gates can provide while retaining TTL-compatible signal levels. Keeping the differential return path close to the signal conductors helps reduce susceptibility to common-mode noise. For PCB implementation, place the device close to the driven line and route each differential conductor as a compact pair. Avoid long stubs, maintain a continuous ground reference, and terminate the line according to its impedance and topology. Verify output current, cable length, logic thresholds, and timing margins under the intended temperature and supply conditions. This product page combines the manufacturer's core electrical and functional information with package-level design guidance, replacement analysis, application examples, and engineering-focused comparison criteria. These supporting sections help engineers distinguish exact family alternatives from broader RS-422, RS-485, and differential-interface devices that may use different packages or logic levels.
SN75116D - 5V Differential Line Transceiver | Texas Instruments
Texas Instruments SN75116D is a 1/1 differential line transceiver with a single 4.5 V to 5.5 V supply, TTL-compatible driver inputs and receiver outputs, and a 16-pin SOIC (D) package. It combines a 3-state differential driver and a differential receiver for bidirectional communication over party-line or data-bus networks. A differential line transceiver is an interface IC that converts between single-ended digital logic signals and differential signals carried by a balanced line. This signal conversion helps equipment communicate more reliably over cables or buses while remaining compatible with TTL-based systems. The SN75116D belongs to the interface IC hierarchy, where transceivers connect digital logic to physical communication lines. The principal features include a 4.5 V to 5.5 V operating supply range, TTL-compatible driver inputs, TTL-compatible receiver outputs, 3-state driver output circuitry, and differential line operation. Its single transceiver arrangement integrates one driver channel and one receiver channel in each 16-pin SOIC package, making it appropriate for compact point-to-point, bus-organized, and party-line interfaces. The SN75116D is designed for party-line and data-bus applications where multiple nodes may share a communication line. The 3-state driver output allows the driver to be disconnected electrically when it is not active, supporting shared-bus architectures. TTL-compatible logic levels simplify interfacing with conventional digital systems, while differential line operation improves signal integrity across the physical transmission path. Typical uses include industrial data acquisition, instrumentation, test equipment, embedded control links, and industrial communication networks. The device is particularly relevant when a system requires bidirectional differential signaling but only one driver and one receiver channel. Its SOIC package also supports conventional surface-mount assembly rather than requiring a through-hole connection. Designers should use the manufacturer datasheet pin-description table when assigning signals and should account for the 4.5 V to 5.5 V supply requirement. The 3-state output must be controlled correctly on a shared bus, and the external line network should be configured to prevent multiple drivers from actively driving the same node at the same time. This page organizes the SN75116D technical characteristics, sourcing information, verified drop-in alternative, interface applications, comparison parameters, and practical PCB design guidance. It helps engineers evaluate the transceiver against same-footprint replacements while keeping electrical compatibility and bus topology central to the selection.
SN75116N - Differential Line Transceiver | Texas Instruments
Texas Instruments SN75116N is a single differential line transceiver containing one 3-state driver and one receiver, operates from a single 5 V supply, and is packaged in a 16-pin PDIP. The device interfaces TTL-type digital systems with differential data-transmission lines and is intended primarily for party-line or data-bus arrangements where multiple nodes can share a bus. Its specified operating-temperature range is 0 to 70 °C. A differential line transceiver is an interface IC that converts between single-ended TTL logic and a differential line signal. This signal hierarchy belongs to the broader sequence of transceiver, interface IC, semiconductor, and electronic communication systems. Differential signaling helps reject common-mode noise because the receiver evaluates the voltage difference between two conductors rather than one conductor referenced only to ground. The SN75116N therefore fits between a bus controller or terminal logic and a physical differential bus. Key features include a single 5 V supply, TTL-compatible driver inputs, TTL-compatible receiver outputs, and a 3-state driver output that allows a connected node to release the bus when inactive. The integrated driver and receiver reduce the number of external interface components needed in a party-line topology. The 16-pin PDIP package also supports conventional through-hole assembly and prototyping workflows. Driver and receiver timing, propagation delay, and bus loading remain important system-level considerations when this device is added to an existing bus. The SN75116N is intended for TTL-to-differential line conversion in party-line data buses. Its 3-state driver supports shared-bus arrangements, while the differential receiver improves noise immunity over a direct single-ended connection. Designers should account for propagation delay, bus termination, cable length, node stub effects, and the voltage margins required by the connected TTL devices. Because the device combines one driver and one receiver, system partitioning may require additional transceivers to balance each node's transmit and receive paths. Typical uses include industrial control buses, instrumentation interfaces, point-to-point differential links, and legacy TTL equipment connected to balanced cabling. The device is also appropriate for laboratory prototypes and repair systems that need a straightforward 16-pin through-hole interface. In every case, the selected cables, connectors, grounding method, and logic family must preserve the voltage thresholds and signal timing expected by the bus. A key implementation consideration is the receiver control function associated with this transceiver family. Confirm the exact control-pin behavior and timing from the manufacturer datasheet before substituting a related family member. When the PCB footprint must remain unchanged, the SN75116N should be treated as a design-specific component rather than replaced solely because another differential transceiver has similar headline features. This page combines the manufacturer's product identity, exact ordering package, commercial sourcing path, functional comparisons, and practical interface-design guidance. It also identifies where timing, pin-level, compliance, and alternative-device details require direct verification before schematic release or PCB reuse.
SN751177NSR - Dual RS-422/RS-485 Transceiver, 10Mbps, 16-SO | TI
The Texas Instruments SN751177NSR is a dual differential driver and receiver pair in a 16-pin Small-Outline (SOIC, NS package) form factor, designed for full-duplex RS-422 and RS-485 balanced multipoint bus transmission at data rates up to 10 Mbits/s. It integrates two drivers and two receivers in a monolithic BiCMOS IC, with positive- and negative-output current limiting on the driver stages for robust bus-fault handling in noisy industrial environments. A transceiver IC is an interface device that converts single-ended logic signals (TTL/CMOS) into the differential voltage levels required by standards such as RS-422 and RS-485, while also converting incoming differential signals back to single-ended logic for a UART, MCU, or ASIC. The RS-485 family in particular enables robust multipoint communication over long twisted-pair cables by using differential signaling with high common-mode rejection, supporting up to 32 nodes on a single bus segment. The SN751177 meets ANSI TIA/EIA-422-B and TIA/EIA-485-A standards as well as ITU-T V.10 and V.11 recommendations, making it suitable for interbuilding and industrial backbone links. Key specifications include 10 Mbits/s signaling rate, a wide 4.75V to 5.25V supply range, 50 mV typical receiver hysteresis for noise immunity, and thermal shutdown with current limiting on the driver outputs. The driver slew-rate design enables reliable 10 Mbps operation without excessive EMI. This part is implemented in TI's bipolar/CMOS mixed process, allowing low power consumption (typical supply current around 50 mA) combined with high drive strength (differential output >2V across 50 ohm loads). The 16-pin SOIC (NS) package provides a compact footprint suitable for point-to-point cables, multidrop backplanes, and isolated data links when paired with digital isolators. An enable pin arrangement supports half-duplex direction control on the SN751178 variant; the SN751177 offers a fixed direction split suitable for full-duplex point-to-point links. Typical applications include factory-floor PLC networking, building-automation RS-485 trunks, point-of-sale (POS) terminals, motor-control encoder feedback links, and industrial sensor aggregation nodes. Its 50 mV receiver hysteresis makes it tolerant of slow edge rates from long cables and opto-isolated interfaces. When designing with the SN751177NSR, ensure proper bus termination (typically 120 ohms across the differential pair at each cable end) and use a fail-safe biasing network to prevent false receiver output during idle bus states. A 100 nF decoupling capacitor placed within 5 mm of the VCC pin is essential for stable high-speed operation. This page synthesizes distributor stock, parametric drop-in alternatives, and practical RS-485 design notes not typically consolidated in the manufacturer datasheet, helping engineers quickly evaluate fit, supply, and second-source options.
SN75117D - 5V Differential Line Transceiver | Texas Instruments
The Texas Instruments SN75117D is a 5 V differential line transceiver in an 8-pin SOIC package, combining a differential driver, a differential receiver, and three-state driver output circuitry in one device. It operates from a single 5 V supply, accepts a maximum supply voltage of 5.5 V, and provides a maximum transmit delay of 30 ns with a maximum receive delay of 75 ns. A differential line transceiver is an interface IC that transmits and receives data across a balanced connection. The transmitter converts a single-ended logic signal into a differential pair, while the receiver detects the voltage difference between the two conductors. Differential signaling rejects common-mode noise, reduces electromagnetic interference, and supports dependable communication over cables or board-level twisted-pair interconnects. The SN75117D features TTL-compatible driver inputs and a TTL-compatible receiver output. Its driver output can be placed in a three-state condition, allowing the driver to be disabled when shared bus direction control is required. The receiver supports differential line operation and includes receiver-output strobe control as a family-level feature of the SN75117 device. The device is intended for balanced data links where low propagation delay, noise immunity, and bus direction control are important. Its 30 ns maximum transmit delay is suitable for moderate-speed control and instrumentation links, while the 75 ns maximum receive delay provides a defined upper limit for receiver-side timing. The single 5 V supply also simplifies interfacing with TTL and other 5 V digital systems. Typical uses include industrial equipment links, instrumentation buses, data acquisition systems, telecommunications equipment, and computer peripherals. In these systems, the SN75117D can place a balanced signal onto a cable, recover the signal at the far end, and provide a logic-compatible receiver output to downstream digital circuitry. PCB design should preserve the differential signal path, use a controlled ground reference, and place termination and protection components close to the line interface. The receiver and driver timing should be checked against the connected cable length and system clock requirements. Power decoupling should follow the manufacturer datasheet layout to minimize supply disturbance during output transitions. This product page combines the manufacturer's device features with practical interface-circuit guidance, timing considerations, package information, sourcing instructions, and design guidance for engineers evaluating the SN75117D in a differential communications design.
SN75118N - 5V Differential Line Transceiver | Texas Instruments
The Texas Instruments SN75118N is a 5 V differential line transceiver that combines a 3-state differential line driver and a differential-input line receiver in a 16-pin PDIP package. It interfaces TTL-type digital systems with balanced data-transmission lines and supports party-line or data-bus arrangements where multiple nodes share one differential pair. Its single 5 V supply, TTL-compatible driver inputs, TTL-compatible receiver output, and separate receiver enable control make it suitable for legacy industrial, communications, instrumentation, and data-acquisition equipment. The SN75118N uses an enable input on the receiver rather than the receiver strobe arrangement used by the related SN75117, allowing the receiving path to be disabled independently of the driver output. The transceiver is designed to place a TTL or CMOS-style logic signal onto a differential line and recover a logic-level output from the differential signal arriving on the same bus. Differential signaling rejects common-mode noise and improves noise immunity when the two line conductors receive equal interference. The driver's 3-state output can be released for party-line operation, preventing a disabled node from blocking the shared bus while another node transmits. The SN75118N family is intended for point-to-point and multipoint data-bus interfaces rather than modern high-rate LAN or automotive Ethernet links. Its differential driver, receiver, and control architecture allow a controller to manage transmit and receive paths within one device. Because it is a legacy bipolar-era interface IC, the design must account for the electrical limits and operating conditions stated in the manufacturer datasheet rather than assuming compatibility with contemporary RS-485 or RS-422 transceivers. The SN75118 is identified by Texas Instruments as a differential line transceiver. The N ordering code denotes the 16-pin PDIP package, measuring 19.3 mm by 9.4 mm with a stated body area of 181.42 mm². The device operates from a single 5 V supply and provides a driver input that accepts TTL-compatible logic levels, a receiver output that drives TTL-compatible logic levels, and a three-state driver output suitable for shared-bus designs. Typical uses include industrial data acquisition, telemetry interfaces, test and measurement equipment, multipoint control buses, and legacy communications equipment. The SN75118N is most appropriate where a 5 V TTL system must connect to a differential line and where transmitter disable and receiver enable functions are required. It is also suitable for systems that need a shared bus rather than a dedicated point-to-point link. When laying out a circuit around the SN75118N, route the differential pair together, keep the driver output in a high-impedance state whenever the node is not transmitting, and follow the receiver-enable polarity shown in the manufacturer pin description table. Confirm the bias and termination arrangement for the specific line length and data rate, because the device is a general-purpose differential transceiver rather than a network PHY with integrated cable compensation. This page organizes the SN75118N specifications, verified sourcing references, and design considerations into a single engineering reference. It also distinguishes the N-package ordering option from related family members whose receiver-control arrangements and package formats differ, helping engineers determine whether a substitute is genuinely pin-to-pin compatible before committing to a PCB change.