بەرهەمەکان (5,100+)

SN65HVD3082EDR - 200kbps Low-Power RS-485 | Texas Instruments
SN65HVD3082EDR

SN65HVD3082EDR - 200kbps Low-Power RS-485 | Texas Instruments

The Texas Instruments SN65HVD3082EDR is a half-duplex RS-485 transceiver designed for 5 V data-bus systems, supporting signaling rates up to 200 kbps in an 8-pin SOIC package. It combines one driver and one receiver with low active quiescent current of 0.3 mA and shutdown current of 1 nA, helping reduce power in distributed industrial, building-automation, and instrumentation networks. The transceiver is designed for balanced twisted-pair buses and supports up to 256 nodes at a 1/8 unit-load configuration. An RS-485 transceiver is an interface IC that combines differential line driver and receiver functions into a two-wire, half-duplex communication link. RS-485 belongs to the broader interface-IC hierarchy and is widely used where multiple distributed devices must communicate over a relatively long cable. Differential signaling improves common-mode noise rejection, while controlled transition times reduce unwanted emissions and help maintain reliable operation across industrial environments. The SN65HVD3082EDR provides one driver and one receiver, a 4.5 V to 5.5 V supply range, and TIA/EIA-485A compliance according to the retrieved manufacturer information. Its low-power architecture is especially useful when the transceiver must remain connected to a bus while minimizing standby consumption. The device also includes bus-pin ESD protection up to 15 kV, a feature important for physically exposed communication ports. Typical applications include industrial RS-485 networks, building-control equipment, factory automation, remote sensor nodes, and low-speed serial data acquisition. The half-duplex arrangement requires the design to manage transmit-enable direction control so that the driver does not contend with the receiver during reception. Bus termination, biasing, grounding, and cable routing remain essential parts of a reliable implementation. The key design consideration is ensuring that the external bus network and transceiver control logic match the application’s transmission direction. A 120-ohm termination resistor is commonly placed at each end of a properly terminated RS-485 cable, while fail-safe biasing should be designed for the system’s idle state. The SOIC-8 package simplifies assembly, but exposed bus pins require careful layout and protection planning. This product page combines verified manufacturer and distributor information, structured application guidance, and explicit data-availability markers for parameters not present in the retrieved source set. It is intended to support engineering comparison and sourcing without inferring unverified electrical values.

RFQ پەیوەندی
SN65HVD30D - 3.3V Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD30D

SN65HVD30D - 3.3V Full-Duplex RS-485 Transceiver | Texas Instruments

The Texas Instruments SN65HVD30D is a 3.3 V full-duplex RS-485 driver and receiver in an 8-pin SOIC package. It combines a differential line driver and differential-input line receiver, with separate driver and receiver input and output pins for full-duplex bus communication designs. The transceiver supports RS-422 and RS-485 data transmission over cable lengths of up to 1500 m, according to the manufacturer product page. The SN65HVD30D is supplied in the D package and is specified for operation from -40°C to 85°C. An RS-485 transceiver is the physical-layer interface between digital logic and a balanced, differential communications bus. The driver converts a differential logic input into balanced line output, while the receiver converts the differential bus voltage into a single-ended logic output. Full-duplex operation requires separate transmit and receive paths, so the SN65HVD30D provides four bus-facing pins in addition to its data-interface and supply pins. Its 3.3 V supply operation supports systems using low-voltage digital logic. The SN65HVD30 is a 3-state differential line driver and differential-input line receiver designed for robust communication links. The device family supports both RS-422 and RS-485 applications, and the SN65HVD30, SN65HVD31, and SN65HVD32 are identified as fully featured members of the SN65HVD3x family by Texas Instruments. The driver and receiver each have independent input and output pins, allowing a controller to transmit and receive simultaneously without sharing the same pair of bus conductors. Typical installations include industrial RS-485 networks, factory automation equipment, building controls, instrumentation, and embedded communications systems. The balanced differential signaling helps reject common-mode noise, while the separate full-duplex channels support continuous two-way communication. Because the interface is intended for cable lengths of up to 1500 m, designers should still evaluate cable impedance, termination, topology, grounding, and transceiver loading for the complete network. For a new layout, place the transceiver and its interface components close to the bus connector and ground-return arrangement, and route differential traces as a closely coupled pair. Decoupling capacitors should be placed directly beside the supply pins, while protection components should be selected to match the cable environment. The 8-pin SOIC package requires careful pin assignment and controlled routing because there is limited space for high-density bypass and protection networks. The SN65HVD30D is most appropriate when a design needs a dedicated 3.3 V full-duplex RS-422 or RS-485 physical layer rather than a half-duplex transceiver with shared driver pins. Designers should verify the complete data sheet for electrical characteristics, enable and disable behavior, receiver thresholds, driver output limits, thermal performance, and recommended application circuits before releasing a production layout. This product overview combines the manufacturer’s device description with practical guidance for interface design. It also provides sourcing answers, application context, design checks, and same-package replacement guidance intended to make component evaluation and PCB planning more efficient.

RFQ پەیوەندی
SN65HVD32D - 3.3V Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD32D

SN65HVD32D - 3.3V Full-Duplex RS-485 Transceiver | Texas Instruments

The Texas Instruments SN65HVD32D is a 3.3 V full-duplex RS-485 and RS-422 transceiver with one driver and one receiver, data rates up to 1 Mbps, and a 3 V to 3.6 V supply range. The device is packaged in an 8-pin SOIC package and is designed for bidirectional differential data transmission over cable lengths up to 1500 meters. An RS-485 transceiver is an interface IC that combines a differential line driver with a differential receiver. It belongs to the interface transceiver class, connects digital logic to a balanced communication bus, and supports noise-resistant transmission in industrial, commercial, and telecommunications systems. The SN65HVD32 family uses separate driver and receiver signal paths for full-duplex communication rather than sharing a single bus direction. Key features include support for up to 256 nodes through the 1/8 unit-load option, bus-pin electrostatic-discharge protection exceeding 15 kV HBM, and driver transition times suitable for 1 Mbps signaling. The 3.3 V operating supply supports modern low-voltage digital systems, while the differential bus interface improves common-mode noise rejection. The SN65HVD32D temperature grade is rated from -40°C to 85°C for the specified D-package ordering option. The SN65HVD3x architecture uses separate input and output pins for full-duplex bus communication. The driver converts logic-level inputs into differential bus outputs, while the receiver converts differential bus inputs into a logic-level output. Because each direction has independent signal pins, the device can transmit and receive simultaneously when the bus, termination, and system design support that operating mode. Typical uses include industrial automation equipment, factory-floor controllers, building automation systems, telecom equipment, data acquisition systems, and other long-distance differential communication networks. In these systems, the transceiver provides the physical-layer interface between a microcontroller, DSP, FPGA, or other controller and a balanced RS-485 bus. Its 1 Mbps capability supports factory automation traffic while the 1/8 unit-load option supports networks containing as many as 256 nodes. PCB design must preserve the differential signal path from the transceiver to the bus connector. Place termination and protection components close to the appropriate bus pins, route the driver and receiver traces as a tightly coupled pair, and provide a low-impedance ground connection. The bus should use twisted-pair cable, with termination applied according to the physical network topology rather than at every node. This page combines manufacturer specifications, interface-application guidance, verified drop-in alternatives, and practical PCB considerations to support component selection, schematic review, and hardware design. It also highlights the distinctions that matter when comparing full-duplex transceivers, bus loading, signaling speed, package compatibility, and node-count requirements.

RFQ پەیوەندی
SN65HVD33D - 3.3V Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD33D

SN65HVD33D - 3.3V Full-Duplex RS-485 Transceiver | Texas Instruments

The Texas Instruments SN65HVD33D is a 3.3 V full-duplex RS-422/RS-485 driver and receiver with a one-eighth unit-load interface, 256-node bus capability, and bus-pin ESD protection exceeding 15 kV HBM. The device is packaged in an 8-pin SOIC (MS-012AA) and supports signaling rates up to 26 Mbit/s, with optional controlled output transition times for 1 Mbit/s signaling. An RS-485 transceiver is an interface IC that combines a differential line driver, differential receiver, and electrical protection for bidirectional data buses. It belongs to the RS-422 and RS-485 transceiver family within the broader interface-IC and semiconductor hierarchy. Full-duplex operation uses separate transmit and receive paths, allowing a node to transmit and receive simultaneously without sharing the same differential pair. Key features include one driver and one receiver in an 8-pin package, 3.3 V operation, one-eighth unit loading, support for as many as 256 nodes on a bus, and fault protection from -9 V to +14 V. The bus pins include ESD protection exceeding 15 kV HBM. A 1 Mbit/s option provides slower driver edges to reduce ringing and electromagnetic interference on longer or imperfectly terminated interconnects. The SN65HVD33D uses differential signaling to reject common-mode noise and support reliable communication over cable distances where single-ended logic would be more susceptible to interference. Independent receiver and driver enable controls support point-to-point links, multidrop buses, industrial equipment, and systems that require controlled direction changes. The 8-pin SOIC package allows straightforward surface-mount assembly and compatibility with standard small-outline PCB land patterns. Typical applications include industrial RS-485 links, building automation equipment, instrumentation, motor-control systems, factory communication networks, and data acquisition systems. Designers should account for the difference between the normal 26 Mbit/s signaling capability and the optional slow-edge behavior intended for 1 Mbit/s buses. Use the manufacturer pin-description table when assigning PCB tracks, and preserve the exposed spacing required by the SOIC footprint. Input and output filtering, bus termination, protection grounding, and enable sequencing should be validated against the actual cable length, topology, data rate, and grounding arrangement. This page combines manufacturer specifications, drop-in replacement guidance, comparative engineering information, and practical interface-design notes. It helps engineers evaluate the SN65HVD33D against electrically similar devices while keeping the same-package and pin-compatibility requirements in view.

RFQ پەیوەندی
SN65HVD34D - 3V Full-Duplex RS-485 Transceiver | TI
SN65HVD34D

SN65HVD34D - 3V Full-Duplex RS-485 Transceiver | TI

Texas Instruments SN65HVD34D is a 3 V full-duplex RS-485 and RS-422 driver and receiver with separate enable controls, supplied in a 14-pin SOIC (D) package. The integrated transceiver provides the physical-layer driver, receiver, and enable functions needed for balanced industrial communication links, while the full-duplex architecture supports simultaneous transmission and reception on separate signal pairs. An RS-485 transceiver is an interface IC that converts logic-level signals between a host controller and a differential bus. The RS-485 standard defines a balanced physical layer for robust data transmission over longer distances and in electrically noisy environments. In the hierarchy of electronic components, the SN65HVD34D belongs to the interface IC family and specifically implements a differential line driver, differential receiver, and bus transceiver for industrial communications equipment. The principal device-level features are its 3 V supply operation, full-duplex communication, RS-485 and RS-422 compatibility, integrated enables, and 14-pin SOIC package. Full-duplex operation is important when transmit and receive paths must operate concurrently rather than sharing a half-duplex bus pair. Separate driver and receiver enables also allow a controller to control the operating state of each circuit independently. The SN65HVD34D belongs to the SN65HVD3x family of 3.3 V full-duplex RS-485 transceivers. Its receiver and driver sections support balanced differential signaling while presenting a conventional digital interface to the surrounding controller. The manufacturer datasheet is the authoritative source for electrical thresholds, propagation delay, driver-output levels, common-mode limits, and recommended external-network values. Typical uses include industrial automation controllers, factory data-acquisition equipment, building-control gateways, motor-control interfaces, and instrumentation connected to RS-485 or RS-422 networks. Because the device supports full-duplex communication, it is particularly appropriate for point-to-point links or multi-drop systems designed with separate driver and receiver bus pairs. When laying out a board, place the transceiver close to the connector and bus-network components, and route the differential pair as a tightly coupled pair with a continuous reference plane beneath it. Confirm the grounding strategy, surge protection, termination, and fail-safe requirements against the manufacturer datasheet for the intended cable and topology. This page provides a sourcing-oriented product summary, same-family drop-in alternatives, application guidance, comparison parameters, and practical PCB considerations. It helps engineers evaluate the SN65HVD34D efficiently while preserving the distinction between published device facts and design-specific engineering decisions.

RFQ پەیوەندی
SN65HVD37D - 3.3V Full-Duplex RS-485 Transceiver | TI (Tape & Reel)
SN65HVD37D

SN65HVD37D - 3.3V Full-Duplex RS-485 Transceiver | TI (Tape & Reel)

The Texas Instruments SN65HVD37D is a low-power, 3.3V full-duplex RS-485/RS-422 transceiver housed in a 14-pin SOIC package. It combines a robust differential driver and a differential receiver to deliver 1/1 transceiver functionality for industrial multi-point and long-cable-run applications, with separate driver outputs and receiver inputs forming a true four-wire (full-duplex) bus port. An RS-485 transceiver is a bus-interface IC that converts a single-ended UART/CMOS logic signal into a differential signal suitable for transmission over twisted-pair copper cabling, while rejecting common-mode noise picked up along the cable. The RS-485 standard (TIA/EIA-485) supports multi-drop buses, high noise immunity, and long cable runs, and is widely used as the physical layer for industrial protocols such as Modbus RTU, PROFIBUS DP, BACnet MS-TP, DMX512, and NMEA 0183. The HVD37 family belongs to the 3.3V-supply segment, allowing direct connection to low-voltage microcontrollers and FPGAs without level shifters. Key specifications include a 3.3V nominal supply (3V to 3.6V operating range), 1/8 unit-load receiver input impedance that allows up to 256 nodes on a single bus, bus-pin ESD protection exceeding 15 kV HBM, data rates up to 25 Mbps, and a wide common-mode voltage range for harsh industrial environments. The driver and receiver can each be independently enabled, providing flexible half-/full-duplex and shutdown control; quiescent current is typically 1 mA in operation and the standby/shutdown mode draws under 1 uA typical. High receiver hysteresis (typ. 60 mV) delivers robust noise immunity on long cables. Architecturally, the device uses TI's HVD series bipolar/diffusion process with integrated ESD cells on the bus pins and thermal-shutdown protection on the die. Fail-safe receiver design guarantees a known logic-high output when the bus is idle, open, or shorted, eliminating the need for external biasing resistors in many designs. The combination of 3.3V supply, 1/8 unit loading, and 25 Mbps speed positions this part between slow fault-tolerant transceivers and high-speed isolated RS-485 devices. Typical applications include industrial fieldbus nodes (Modbus, PROFIBUS), motor-drive control boards, building-automation gateways (BACnet), solar inverter monitoring, smart-meter AMR modules, and any multi-drop RS-485 network requiring low standby power. Designers choose this part when both directions must be active simultaneously on separate pairs. Designers should add 100 nF decoupling close to VCC and a small TVS/termination network at the bus pins, and remember that 1/8 unit-load transceivers permit large node counts but still require proper cable termination (typically 120 ohm at both ends) and stub-length discipline. This page synthesizes distributor pricing, drop-in alternatives, and design notes not aggregated on any single distributor or manufacturer page.

RFQ پەیوەندی
SN65HVD37DR - 3.3V Full-Duplex RS-485 Transceiver | TI
SN65HVD37DR

SN65HVD37DR - 3.3V Full-Duplex RS-485 Transceiver | TI

The Texas Instruments SN65HVD37DR is a low-power, 3.3V full-duplex RS-485/RS-422 transceiver housed in a 14-pin SOIC package. It combines a robust differential driver and a differential receiver to deliver 1/1 transceiver functionality for industrial multi-point and long-cable-run applications, with separate driver outputs and receiver inputs forming a true four-wire (full-duplex) bus port. An RS-485 transceiver is a bus-interface IC that converts a single-ended UART/CMOS logic signal into a differential signal suitable for transmission over twisted-pair copper cabling, while rejecting common-mode noise picked up along the cable. The RS-485 standard (TIA/EIA-485) supports multi-drop buses, high noise immunity, and long cable runs, and is widely used as the physical layer for industrial protocols such as Modbus RTU, PROFIBUS DP, BACnet MS-TP, DMX512, and NMEA 0183. The HVD37 family belongs to the 3.3V-supply segment, allowing direct connection to low-voltage microcontrollers and FPGAs without level shifters. Key specifications include a 3.3V nominal supply (3V to 3.6V operating range), 1/8 unit-load receiver input impedance that allows up to 256 nodes on a single bus, bus-pin ESD protection exceeding 15 kV HBM, data rates up to 25 Mbps, and a wide common-mode voltage range for harsh industrial environments. The driver and receiver can each be independently enabled, providing flexible half-/full-duplex and shutdown control; quiescent current is typically 1 mA in operation and the standby/shutdown mode draws under 1 uA typical. High receiver hysteresis (typ. 60 mV) delivers robust noise immunity on long cables. Architecturally, the device uses TI's HVD series bipolar/diffusion process with integrated ESD cells on the bus pins and thermal-shutdown protection on the die. Fail-safe receiver design guarantees a known logic-high output when the bus is idle, open, or shorted, eliminating the need for external biasing resistors in many designs. The combination of 3.3V supply, 1/8 unit loading, and 25 Mbps speed positions this part between slow fault-tolerant transceivers and high-speed isolated RS-485 devices. Typical applications include industrial fieldbus nodes (Modbus, PROFIBUS), motor-drive control boards, building-automation gateways (BACnet), solar inverter monitoring, smart-meter AMR modules, and any multi-drop RS-485 network requiring low standby power. Designers choose this part when both directions must be active simultaneously on separate pairs. Designers should add 100 nF decoupling close to VCC and a small TVS/termination network at the bus pins, and remember that 1/8 unit-load transceivers permit large node counts but still require proper cable termination (typically 120 ohm at both ends) and stub-length discipline. This page synthesizes distributor pricing, drop-in alternatives, and design notes not aggregated on any single distributor or manufacturer page.

RFQ پەیوەندی
SN65HVD50D - 25Mbps RS-485/RS-422 Transceiver | Texas Instruments
SN65HVD50D

SN65HVD50D - 25Mbps RS-485/RS-422 Transceiver | Texas Instruments

The Texas Instruments SN65HVD50D is a high-output, full-duplex RS-485 and RS-422 interface transceiver designed for reliable point-to-point and multipoint communications. It operates from a 4.5 V to 5.5 V supply, supports signaling rates up to 25 Mbps, and combines one driver with one receiver in an 8-pin SOIC package. The device includes selectable driver transition-time options for 1 Mbps, 5 Mbps, and 25 Mbps signaling, allowing designers to balance transmission distance, signal integrity, and electromagnetic compatibility requirements. An RS-485 transceiver is an interface IC that converts logic-level signals into differential bus voltages and receives differential bus signals back into logic-level outputs. This product belongs to the broader RS-485 transceiver family, which is part of the interface IC category and supports industrial, telecommunications, building automation, instrumentation, and data-communication equipment. The SN65HVD50D is appropriate where a system requires a dedicated full-duplex RS-485 or RS-422 interface rather than a half-duplex transceiver. Key features include 1/8 unit-load operation for networks containing as many as 256 nodes, bus-pin ESD protection exceeding 15 kV HBM, and a low-current standby mode with 1 µA typical standby current. The receiver provides 50 mV hysteresis, which helps improve noise immunity during differential signaling. The 25 Mbps maximum data rate makes the device suitable for high-speed data links where cable length and topology must be considered carefully. The SN65HVD50D is a single-channel transceiver with separate transmit and receive paths, allowing full-duplex communication. Its high-output driver is intended for driving differential cables and interconnects while maintaining robust signal margins. The manufacturer product page identifies the device as a High Output Full-Duplex RS 485 Driver and Receiver, while distributor listings identify the package as 8-SOIC and describe it as an RS-422/RS-485 interface IC. Typical applications include industrial control networks, factory automation equipment, instrumentation systems, building-control networks, and high-speed industrial data links. When selecting it, engineers should verify cable length, node count, termination, common-mode range, grounding, and connector requirements against the complete manufacturer datasheet before layout release. A practical design consideration is that the driver transition-time setting affects edge rate and therefore can influence EMI behavior. Keep the differential pair routed with controlled geometry, provide the required bus protection and termination, and validate the complete board-level signal integrity at the selected data rate. This page combines manufacturer and distributor information with application guidance, comparison criteria, and drop-in replacement findings to support faster engineering evaluation.

RFQ پەیوەندی
SN65HVD51D - 5Mbps Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD51D

SN65HVD51D - 5Mbps Full-Duplex RS-485 Transceiver | Texas Instruments

Texas Instruments SN65HVD51D is a high-output, full-duplex RS-422/RS-485 interface transceiver with one driver and one receiver, a maximum signaling rate of 5 Mbps, a 4.5 V to 5.5 V supply range, and an 8-pin SOIC package. The device provides separate driver and receiver paths for balanced industrial communications. An RS-485 transceiver is an interface IC that converts logic-level signals into differential bus signals and converts received differential signals back into logic levels. It belongs to the communication-interface hierarchy: RS-422/RS-485 transceiver, differential line driver and receiver, interface IC, and semiconductor. This signal conversion allows equipment to communicate reliably over longer cable runs, especially in industrial environments where common-mode noise and ground-potential differences can disrupt single-ended signaling. Key features include a one-eighth unit-load option supporting as many as 256 nodes on a bus, bus-pin electrostatic-discharge protection exceeding 15 kV HBM, and optional driver output transition times for 1 Mbps, 5 Mbps, and 25 Mbps signaling. The SN65HVD51D also supports a low-current standby mode below 1 µA and provides glitch-free operation. Its high-output design is intended for industrial communication and data-transmission systems using balanced transmission lines. The SN65HVD51 family operates from a 5 V supply and is offered in an 8-pin SOIC package. The D ordering option is specified for operation from -40 °C to 85 °C. According to the Texas Instruments product information, the SN65HVD51, SN65HVD50, and SN65HVD52 are fully enabled and have no external enable pins, allowing continuous operation without external driver or receiver control. The D suffix identifies the 8-pin SOIC package rather than a different transceiver function. Typical applications include industrial automation controllers, factory data-acquisition equipment, remote sensor interfaces, building-control systems, and communications equipment operating in electrically noisy environments. Full-duplex operation permits simultaneous transmission and reception on separate differential pairs, while the one-eighth unit-load capability helps designers connect more nodes than a conventional one-unit-load receiver would support. When laying out a board, use a controlled-impedance differential pair for each bus direction, provide a continuous ground reference, and place termination, protection, and common-mode components at the physical bus interface. Supply decoupling should be placed close to the device. Because RS-485 communication quality also depends on cable characteristics, grounding, topology, and termination—not only the transceiver—validate the complete channel in the target environment. This page combines verified Texas Instruments product information, distributor availability references, cross-reference results, and practical engineering guidance. It also distinguishes the confirmed pin-compatible THVD1451 replacement from same-family Texas Instruments alternatives whose enable and electrical characteristics require board-level verification before substitution.

RFQ پەیوەندی
SN65HVD52D - 1 Mbps Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD52D

SN65HVD52D - 1 Mbps Full-Duplex RS-485 Transceiver | Texas Instruments

The Texas Instruments SN65HVD52D is a high-output, full-duplex RS-485 driver and receiver interface IC operating at a 1 Mbps data rate. It is packaged in an 8-pin SOIC (D) and provides one driver and one receiver for balanced RS-422 and RS-485 communications. The device is intended for industrial, instrumentation, communications, and data-acquisition systems where a low-noise differential physical-layer interface is required. According to the manufacturer product page, SN65HVD52D is a High Output Full-Duplex RS-485 Driver and Receiver in an 8-pin SOIC package. An RS-485 transceiver is a physical-layer interface device that combines a differential line driver with a differential line receiver. The driver converts a single-ended logic signal into a balanced differential signal, while the receiver converts the differential bus voltage back into a logic signal. Full-duplex operation provides separate transmit and receive paths, allowing a system to transmit and receive simultaneously when the bus wiring and protocol support it. This makes the SN65HVD52D suitable for point-to-point links, multidrop RS-422 systems, and full-duplex RS-485 networks. The SN65HVD52D is specified for operation from a 5 V supply and supports signaling rates up to 1 Mbps. The SN65HVD5X family includes low-current standby operation, glitch-free operation, and selectable driver transition-time options for different signaling rates. The device also supports an eighth-unit-load option, allowing substantially larger bus populations than a standard unit-load transceiver when system capacitance and topology permit. Bus-pin ESD protection exceeds 15 kV HBM according to the device documentation. Typical applications include industrial automation links, programmable-logic-controller communication, factory-floor equipment, building-control networks, instrumentation, motor-control systems, and industrial data-acquisition equipment. The receiver is designed for balanced differential inputs, while the driver produces a high-output differential signal suitable for reliable communication over longer cable runs when the system uses proper termination and biasing. When designing around the SN65HVD52D, verify the data rate, cable length, topology, termination, and common-mode range together. The 8-pin SOIC footprint is compatible with conventional surface-mount assembly, but the exact pin function and enable or standby behavior must be checked in the manufacturer pin-description table. This page combines device specifications, practical application guidance, package information, and verified source links for engineering evaluation.

RFQ پەیوەندی
SN65HVD53D - High-Output Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD53D

SN65HVD53D - High-Output Full-Duplex RS-485 Transceiver | Texas Instruments

The Texas Instruments SN65HVD53D is a high-output, full-duplex RS-485 and RS-422 transceiver with driver and receiver enable pins, packaged in a 14-pin SOIC (D). It combines one differential driver and one differential receiver with independent active-high driver enable (DE) and active-low receiver enable (RE) control, and it offers a 1/8 unit-load receiver option supporting up to 256 nodes on a single bus. A transceiver is the physical-layer interface that converts between a logic-level digital signal and a balanced differential line pair. An RS-485 transceiver belongs to the differential line-driver / receiver family, which sits under interface ICs, communication ICs, and ultimately semiconductor ICs. Differential signaling carries the same data on two wires of opposite polarity, so common-mode noise induced along the cable is rejected by the receiver, making RS-485 the dominant industrial bus for factory automation, instrumentation, and building control. Key differentiators of this device include bus-pin ESD protection exceeding 15 kV HBM, selectable driver output transition times supporting signaling rates of 1 Mbps, 5 Mbps and 25 Mbps, a low-current standby mode drawing about 1 uA when both the driver and receiver are disabled, and glitch-free receiver outputs. The 14-pin SOIC body measures 3.90 mm wide and is rated for -40 C to +85 C operation, covering industrial temperature ranges without a hermetic or extended package. Internally, the SN65HVD53D uses a differential driver stage with selectable slew rate to control edge energy on the bus and limit EMI, while the receiver front end presents a low unit load so many nodes can share one cable run. Enable pins give the system designer direct control over bus direction and shutdown, which is valuable in multi-drop networks where multiple transceivers must not all drive simultaneously. Typical deployments include industrial RS-485 field buses, PLC and remote I/O links, building HVAC and access-control networks, utility and metering equipment, and instrumentation links where a full-duplex point-to-point topology with separate driver and receiver enables is required. When laying out the board, keep the differential pair tightly coupled with a continuous ground reference beneath it, place the bypass capacitors at the supply pins, and treat the enable pins as digital control signals that must be sequenced so that only one node drives the bus at a time. This page consolidates device specifications, enable-logic differences against sibling family members, drop-in alternatives, and practical layout guidance into a single engineering reference that goes beyond a basic catalogue entry.

RFQ پەیوەندی
SN65HVD54D - 5 Mbps Full-Duplex RS-485 | Texas Instruments
SN65HVD54D

SN65HVD54D - 5 Mbps Full-Duplex RS-485 | Texas Instruments

The Texas Instruments SN65HVD54D is a high-output, full-duplex RS-485 driver and receiver with separate driver and receiver enables, operating from a single 5 V supply in a 14-pin SOIC (D) package. It supports signaling rates up to 5 Mbps, provides a 1/8-unit-load option for as many as 256 nodes on a bus, and includes bus-pin ESD protection exceeding 15 kV HBM. The device also offers a low-current standby mode with 1 µA typical standby current and selectable driver transition times optimized for 1 Mbps, 5 Mbps, and 25 Mbps signaling environments. An RS-485 transceiver is an interface integrated circuit that combines a differential line driver and differential receiver for balanced digital communications. It belongs to the RS-422/RS-485 transceiver hierarchy within interface ICs, where the driver translates logic-level signals into differential bus voltage and the receiver converts differential bus voltage back into a logic-level signal. Full-duplex operation provides separate paths for transmission and reception, making the SN65HVD54D suitable for systems that cannot share the same bus conductors in both directions. The SN65HVD54D provides one driver and one receiver, with independent enables that allow the system to place either side into a low-power state. Its high-output architecture is intended for demanding balanced-line links, while the selectable driver edge rates let engineers optimize signaling behavior for 1 Mbps, 5 Mbps, or faster communication links. The 1/8-unit-load receiver option can support up to 256 nodes, reducing the loading burden in large multi-node industrial systems. Bus-pin ESD protection exceeding 15 kV HBM adds an important ruggedness margin where cables and external connectors are exposed to electrostatic discharge. The device operates across the -40 °C to +85 °C temperature range in the SN65HVD54D ordering option. Its separate full-duplex driver and receiver structure is particularly useful when the transmitting and receiving nodes must remain active simultaneously. Typical uses include industrial factory automation, building-control networks, industrial instrumentation, motor-control systems, process monitoring, and other full-duplex RS-485 links. The 5 Mbps capability supports factory-floor communication, while the standby function can reduce consumption when a node is not communicating. Component placement and termination remain important because the transceiver does not eliminate the need for a balanced cable, appropriate bus topology, and correctly engineered termination. Designers should verify enable polarity in the host logic, place the device close to the bus connector, and provide protection appropriate to the installation environment. The internal high-impedance state supports controlled bus participation, but software and fault-management circuitry must still prevent multiple transmitters from driving the same bus at the same time. This page consolidates verified manufacturer and distributor information, package details, lifecycle attributes, replacement guidance, and application-oriented engineering context. It also distinguishes documented drop-in family options from alternatives that may require different packages or interface behavior, helping engineers shorten component-selection and PCB-validation work.

RFQ پەیوەندی
SN65HVD55D - 1Mbps Full-Duplex RS-485 | Texas Instruments
SN65HVD55D

SN65HVD55D - 1Mbps Full-Duplex RS-485 | Texas Instruments

The Texas Instruments SN65HVD55D is a high-output, full-duplex RS-485 driver and receiver with enables, supporting data rates up to 1 Mbps and operation from -40°C to +85°C in a 14-pin SOIC package. It provides a 1/8-unit-load option for networks containing as many as 256 nodes, 50 mV receiver hysteresis for improved noise immunity, and bus-pin ESD protection exceeding 15 kV HBM. An RS-485 transceiver is a bidirectional communications interface that combines a differential line driver, a differential receiver, and associated enable controls. It belongs to the interface-IC hierarchy and enables robust communication over long, noisy cables by representing digital data as a differential voltage across a balanced pair of conductors. The SN65HVD55D uses separate driver and receiver paths, allowing full-duplex operation on a four-wire bus. Key features include a maximum data rate of 1 Mbps, 1/8-unit-load operation, and optional driver transition times intended for signaling rates of 1 Mbps, 5 Mbps, and 25 Mbps. The low-current standby mode consumes 1 µA, making the enables useful for power-conscious systems. Bus-pin ESD protection exceeding 15 kV HBM helps improve robustness where cables connect the transceiver to external equipment. The high-output architecture increases the amount of signal energy available on the bus, while the receiver's 50 mV hysteresis rejects noise within the transition region between differential output states. The device is suitable for RS-422 and RS-485 equipment where point-to-point or multipoint differential signaling is required. Its independent enable controls permit the driver and receiver to be switched according to the operating state of the connected system. Typical applications include industrial automation equipment, factory-floor controllers, building-control systems, data-acquisition equipment, communications modules, and external bus interfaces. In a full-duplex installation, the driver connects to one differential pair and the receiver connects to another pair, allowing simultaneous transmission and reception without sharing the same bus conductors. Designers should account for cable length, topology, termination, grounding, and the slew-rate option when selecting the device. The bus must remain within the transceiver's specified electrical limits, and unused inputs should be handled according to the manufacturer guidance. Enable sequencing should also prevent simultaneous bus contention where multiple nodes share a conductor pair. This product page combines the verified manufacturer description, distributor availability, package information, RS-485 operating characteristics, and documented family differences. It also provides application guidance and a structured comparison for engineers evaluating drop-in interface choices without adding unverified electrical claims.

RFQ پەیوەندی
SN65HVD61D - Single-Channel ControlNet Transceiver | Texas Instruments
SN65HVD61D

SN65HVD61D - Single-Channel ControlNet Transceiver | Texas Instruments

Texas Instruments SN65HVD61D is a single-channel ControlNet physical-layer transceiver with one driver and one receiver, supplied in a 14-pin SOIC package. Designed for single-node operation and distributed stand-alone applications, it provides the circuitry required by ControlNet coaxial-based physical layers. Its pull-or-pull transmitter sinks current from a center-tapped transformer, supporting galvanic isolation between the transceiver circuitry and the external network interface. The combination of one integrated transceiver channel, transformer-compatible drive topology, and a compact 14-SOIC package makes the device applicable to industrial automation, controller, sensor, and factory-control networks. A ControlNet transceiver is a specialized interface IC that converts digital logic signals into a balanced physical-layer network connection and converts received network signals back into logic-level data. Within the product hierarchy, it belongs to the interface transceiver class, with ControlNet operation representing its defining protocol and physical-layer function. Its isolation-oriented transmitter arrangement is particularly useful where system designers require a transformer-based link between the transceiver and a coaxial cable network. The SN65HVD61D integrates one driver and one receiver into a single channel. The manufacturer describes the transmitter as a pull-or-pull arrangement that sinks current from a center-tapped transformer rather than driving the cable directly. This architecture allows the external transformer to establish the physical signal coupling and galvanic isolation. The 14-SOIC package supports conventional surface-mount assembly while providing a practical pin count for a complete single-channel interface. The primary system benefit is functional consolidation: one device contains both sides of the ControlNet physical-layer connection. This can reduce the number of separate interface components required for a single-node or stand-alone node. The galvanic-isolation capability provided by the center-tapped transformer arrangement is also important in industrial environments where isolation between the electronic circuitry and external cabling is a system requirement. Actual isolation voltage, data rate, supply range, and timing limits must be confirmed in the manufacturer datasheet before final qualification. Typical use cases include ControlNet-compatible programmable logic controllers, industrial automation controllers, remote I/O nodes, factory sensor interfaces, motor-control supervisory nodes, and distributed process-monitoring equipment. In each case, the SN65HVD61D handles the local logical transceiver function while a suitable center-tapped transformer connects the device to the ControlNet physical layer. The primary design consideration is transformer and network compatibility. The external center-tapped transformer must match the device's electrical and timing requirements, and its wiring must preserve the intended isolation boundary. PCB signal integrity, return paths, bypass-capacitor placement, and connector or cable characteristics also require careful implementation because the transceiver communicates through a coupled physical layer rather than a direct point-to-point logic interface. This page consolidates the verified manufacturer description, distributor identification, package information, sourcing links, and practical engineering guidance. It also distinguishes the SN65HVD61D from family ordering variants and identifies where additional electrical, timing, compliance, or lifecycle data must be obtained from the authoritative manufacturer documentation.

RFQ پەیوەندی
SN65HVD70DGSR - 3.3V Full-Duplex RS-485 400kbps Transceiver, 10-VSSOP | Texas Instruments
SN65HVD70DGSR

SN65HVD70DGSR - 3.3V Full-Duplex RS-485 400kbps Transceiver, 10-VSSOP | Texas Instruments

The Texas Instruments SN65HVD70DGSR is a 3.3 V, full-duplex RS-485 transceiver rated for data rates up to 400 kbps, integrating ±12 kV IEC 61000-4-2 contact discharge ESD protection, in a 10-pin VSSOP (DGS) PowerPAD package. The device pairs one differential driver with one differential receiver, each with dedicated input/output pins, enabling simultaneous transmit and receive on a four-wire bus typical of RS-422 and full-duplex RS-485 networks. The driver includes active-high enable control and the receiver includes active-low enable control, allowing a sub-5 µA standby current when both functions are disabled. A transceiver of this class is the physical-layer interface between a UART/MCU and a differential twisted-pair cable in industrial multipoint networks. The SN65HVD70 extends TI's RS-485 portfolio as a low-power, robust 3.3 V member of the SN65HVD7x family, suitable for half- and full-duplex links across factory floors, building automation, and motor-drive backplanes. As a line transceiver it sits hierarchically below the protocol layer (Modbus, PROFIBUS, DMX512) and above the cable plant, converting CMOS/TTL logic levels into the differential A/B signaling defined by TIA/EIA-485-A and TIA/EIA-422-B. Key features include ±30 kV HBM ESD on the bus pins, a wide 3.0 V to 3.6 V supply range, a 1.8 V to 5 V logic interface (no level shifter needed in 1.8 V systems), open-circuit, short-circuit, and bus-idle fail-safe receiver inputs, and a thermal-shutdown protected driver. The 10-pin VSSOP package with thermal pad keeps the footprint compact while supporting industrial -40 °C to +125 °C operation. The device uses a precision differential architecture with large receiver hysteresis (typically 50 mV) to reject common-mode noise on long cable runs. The wide common-mode range of -7 V to +12 V tolerates ground potential differences between nodes, and the 1/8 unit-load option permits up to 256 nodes on a single bus. Slew-rate limiting reduces EMI reflections on unterminated stubs. Typical applications include industrial multi-drop RS-485 networks, building-automation backbones, motor-control command links, point-of-sale peripherals, and full-duplex RS-422 point-to-point data links. The device is well matched to long cable runs with proper 120 Ω termination at both ends. When designing with this part, place 100 nF decoupling capacitors within 2 mm of VCC and use a 120 Ω termination resistor at each end of the bus. Do not leave unused driver outputs floating - tie them to GND through a resistor. Maintain a 1/8 unit-load budget when scaling beyond 32 nodes. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including cross-vendor equivalents and full intent coverage in the FAQ for engineers planning second-source qualification.

RFQ پەیوەندی
SN65HVD71D - 400kbps Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD71D

SN65HVD71D - 400kbps Full-Duplex RS-485 Transceiver | Texas Instruments

Texas Instruments SN65HVD71D is a 3.3 V full-duplex RS-485 and RS-422 transceiver with one driver and one receiver, a 400 kbps data rate, and 12 kV IEC ESD protection. It is packaged in an 8-pin SOIC (D) package and operates without driver or receiver enable controls. The separate driver input and receiver output pins support simultaneous bidirectional communication on a multidrop industrial bus. An RS-485 transceiver is an interface integrated circuit that converts logic-level signals into differential bus signals and converts received differential signals back into CMOS-compatible logic. RS-485 extends communication distance and noise immunity compared with single-ended interfaces by using balanced differential signaling. This family belongs to the interface IC hierarchy: transceiver > RS-485 interface > differential bus interface > semiconductor. The SN65HVD71D provides a 3.3 V supply range of 3 V to 3.6 V, operation from -40 °C to +125 °C, and a data rate up to 400 kbps. Its 12 kV IEC-rated ESD protection helps protect the transceiver when cables are connected to external equipment. Full-duplex operation allows transmitting and receiving simultaneously, which is useful for point-to-point links and systems that cannot wait for a bus turnaround. Internally, the device combines one differential driver and one differential receiver. The driver accepts a CMOS-compatible transmit input, while the receiver produces a CMOS-compatible receive output. The absence of enable pins simplifies control logic, although the design must manage bus direction externally when the transceiver is connected to a shared multidrop network. Typical applications include industrial RS-485 links, building automation, factory equipment, motor-control systems, security equipment, and other long-distance serial networks. The device can also support point-to-point RS-422-style connections when the system requires independent transmit and receive paths. Designers should check the pin assignment and termination requirements in the manufacturer datasheet before layout. A 120-ohm termination resistor is commonly used at each end of a standard RS-485 bus, while bias resistors should be placed only where required. Keep the differential pair routed together, minimize stubs, and provide a stable return path to reduce common-mode noise. This product page combines the manufacturer's electrical specifications with practical interface guidance, application context, comparison information, and verified sourcing references. It is intended to help engineers identify whether the SN65HVD71D fits a 3.3 V full-duplex RS-485 design before beginning PCB implementation.

RFQ پەیوەندی
SN65HVD72D - 3.3V 250kbps Half-Duplex RS-485 | Texas Instruments
SN65HVD72D

SN65HVD72D - 3.3V 250kbps Half-Duplex RS-485 | Texas Instruments

The Texas Instruments SN65HVD72D is a 3.3 V half-duplex RS-485 transceiver with IEC ESD protection and a maximum signaling rate of 250 kbps, packaged in an 8-pin SOIC (D) package. It combines one RS-485 driver and one RS-485 receiver in a single integrated circuit, making it suitable for bidirectional industrial communication links using differential bus wiring. The part is identified by Texas Instruments as an active product with an operating temperature range of -40 °C to 125 °C and RoHS-compliant construction. An RS-485 transceiver is an interface IC that translates between a logic-level UART or digital signal and a differential RS-485 bus. The differential architecture supports noise-resistant communication over longer cable runs than single-ended signaling, while the half-duplex arrangement allows the same pair of bus conductors to support both transmission and reception. In this device, the 3.3 V supply and 250 kbps data rate suit embedded systems, industrial controllers, sensors, and equipment using low-speed field-bus links. Key verified characteristics include a 3.3 V supply, 250 kbps maximum signaling rate, half-duplex operation, RS-422/RS-485 transceiver functionality, and IEC ESD protection. The SOIC-8 package provides a compact surface-mount footprint for industrial control boards and communication modules. The device is marketed for demanding industrial applications where robust bus interfacing and protection are important. The SN65HVD72D integrates the physical-layer functions needed to connect a microcontroller or programmable logic controller to a differential RS-485 network. Designers should pay attention to bus biasing, termination, grounding, cable length, and the exact logic-control requirements of the selected family variant. The manufacturer product page and part-details page are the authoritative sources for ordering information, electrical characteristics, and package details. Typical uses include industrial automation equipment, remote sensor interfaces, building-control systems, instrumentation, and embedded serial networks. Compared with lower-speed or more highly integrated interface solutions, the SN65HVD72D provides a focused 250 kbps half-duplex RS-485 solution with ESD protection in a standard 8-pin SOIC package. This page combines verified manufacturer and distributor information with practical selection guidance, pricing context, and application notes for engineers evaluating the SN65HVD72D.

RFQ پەیوەندی
SN65HVD73D - 20Mbps Full-Duplex RS-485 | TI
SN65HVD73D

SN65HVD73D - 20Mbps Full-Duplex RS-485 | TI

The Texas Instruments SN65HVD73D is a 3.3 V full-duplex RS-485/RS-422 transceiver with a 20 Mbps maximum data rate, ±12 kV IEC ESD protection, and individual driver and receiver enables in a 14-pin SOIC (D) package. The device integrates one driver and one receiver, supports a 3 V to 3.6 V supply range, operates across -40°C to +125°C, and provides 70 mV receiver hysteresis. An RS-485 transceiver is a physical-layer interface IC that converts low-voltage digital logic signals into differential bus signals and reconstructs logic-level data from a differential bus. It belongs to the transceiver hierarchy within interface ICs and enables robust, point-to-point or multidrop communication over longer distances than single-ended logic interfaces. Full duplex means the driver and receiver can operate simultaneously on separate differential pairs. The SN65HVD73D's principal features include a 20 Mbps data rate, 70 mV receiver hysteresis, separate active-high driver enable and active-low receiver enable controls, and ±12 kV IEC-rated ESD protection. Its 3 V to 3.6 V operating range is appropriate for 3.3 V systems. The broad -40°C to +125°C temperature range supports industrial and extended-temperature equipment when the complete system qualification permits it. The integrated driver and receiver provide one RS-485/RS-422 communication channel in full-duplex configuration. Separate enables allow the transmitter and receiver to be disabled independently, and the manufacturer product page states that standby current can be reduced below 5 µA when both functions are disabled. A common ground reference and carefully terminated differential wiring remain necessary for reliable operation. Typical applications include industrial control networks, factory automation equipment, data acquisition systems, building-automation controllers, and communications between a host controller and a peripheral transceiver. The 20 Mbps capability supports high-speed point-to-point links, while the ±12 kV IEC ESD rating helps protect external bus connectors in electrically noisy environments. Designers should follow the manufacturer datasheet for transceiver pinout, termination, fail-safe biasing, and differential routing. Keep the RS-485 differential pair routed as a controlled-impedance pair, minimize stub lengths, place termination only where required by the bus topology, and verify grounding and surge-protection requirements for the installed environment. This product summary consolidates verified manufacturer and distributor information, supply parameters, design guidance, and replacement constraints into one engineering-focused reference. It also clearly distinguishes verified specifications from electrical values that require confirmation from the complete datasheet before schematic release.

RFQ پەیوەندی
SN65HVD73DGS - 3.3V Full-Duplex RS-485 20Mbps | Texas Instruments
SN65HVD73DGS

SN65HVD73DGS - 3.3V Full-Duplex RS-485 20Mbps | Texas Instruments

The Texas Instruments SN65HVD73DGS is a 3.3 V full-duplex RS-485 transceiver with integrated active-high driver enable and active-low receiver enable pins, supporting data rates up to 20 Mbps in a 10-pin VSSOP (DGS) package. It integrates a differential driver, a differential receiver, and 12 kV IEC ESD protection on bus pins, operating from a single 3.3 V supply across the industrial -40°C to +125°C temperature range. The device is designed for high-speed, half-duplex-to-full-duplex RS-485 networks in industrial automation, motor control, and point-to-point data links. A RS-485 transceiver is a balanced differential line driver/receiver IC that converts a single-ended TTL/CMOS logic signal into a differential signal conforming to the TIA/EIA-485-A standard, enabling robust multi-drop communication over twisted-pair cable with common-mode voltage tolerance up to ±25 V and cable lengths up to 1200 m at reduced data rates. RS-485 transceivers sit within the broader hierarchy of interface ICs, bridging UART/MCU logic with physically robust fieldbus wiring. The SN65HVD73DGS belongs to the 3.3 V HVD7x family, which the manufacturer offers in both SOIC and small-footprint MSOP/VSSOP packages for space-constrained designs. Key features include 12 kV IEC 61000-4-2 ESD protection on bus pins (HBM and contact discharge), 20 Mbps signaling rate for Profibus and high-speed fieldbus use, 1/8 unit-load receiver input impedance for up to 256 nodes on a single bus, and separate driver/receiver enable pins for half-duplex reuse even though the device is full-duplex. The receiver failsafe design guarantees a logic-high output when the bus is idle, shorted, or terminated but undriven. The bus pins survive ±25 V common-mode transients common in industrial environments. Architecturally, the SN65HVD73DGS uses a 3.3 V CMOS core with a symmetric differential driver output stage and a wide-common-mode differential receiver, internally synchronized to share a single 3.3 V supply rail. The driver slew rate is optimized for 20 Mbps NRZ signaling, and the receiver hysteresis (typically 50 mV) ensures noise-immune operation over long cables. Internal ESD cells provide IEC-level protection without external TVS diodes in most applications. Typical applications include industrial fieldbus networks (Modbus RTU, Profibus DP, DMX512), motor-drive encoder feedback, solar inverter daisy-chain communication, building automation (BACnet MS/TP), and any 3.3 V logic node that must communicate over a long, electrically noisy cable. Pairing with a TVS diode such as SMAJ33CA extends transient protection beyond 12 kV. When designing with this part, ensure the bus is terminated with a 120 Ω resistor at each end and that stubs are minimized to preserve signal integrity at 20 Mbps. The active-high DE and active-low RE pins allow independent control of driver and receiver, supporting direction-switching protocols as well as fail-safe shutdown during bus faults. Decouple VCC with a 0.1 µF ceramic capacitor placed within 5 mm of the supply pin.

RFQ پەیوەندی
SN65HVD73DGSR - 3.3V Full-Duplex RS-485, 20Mbps, 12kV ESD | TI
SN65HVD73DGSR

SN65HVD73DGSR - 3.3V Full-Duplex RS-485, 20Mbps, 12kV ESD | TI

The Texas Instruments SN65HVD73DGSR is a 3.3-V full-duplex RS-485 transceiver with separate driver and receiver pins, 20 Mbps signaling rate, and ±12-kV IEC 61000-4-2 contact ESD protection, housed in a 10-pin MSOP/VSSOP (DGS) package. The wide common-mode voltage range makes the device suitable for multi-point RS-485 / RS-422 bus applications over long cable runs in industrial, building automation, and motor-control networks. A RS-485 transceiver is a physical-layer interface IC that converts between a low-voltage UART/logic-level signal on the controller side and a balanced differential signal on the bus side. Full-duplex (a.k.a. 4-wire RS-485) uses separate differential pairs for transmit and receive, allowing simultaneous two-way communication. The SN65HVD73 belongs to the broader family of half- and full-duplex RS-485 transceivers -> differential line transceivers -> interface ICs -> integrated circuits in the data-communication hierarchy defined by TIA-485 / EIA-422 standards. Key features include 3.3-V single-supply operation (compatible with modern low-power MCUs and FPGAs), 20 Mbps maximum data rate, ±30-kV HBM and ±12-kV IEC 61000-4-2 contact-discharge ESD on bus pins, large receiver hysteresis for noise immunity in harsh industrial environments, 1/8 unit-load support that lets up to 256 nodes share one bus, and separate driver-enable (DE) and receiver-enable (RE) pins for direction control and half-duplex reuse. Operating temperature spans -40 °C to +125 °C. The architecture uses a differential line driver and differential line receiver with a wide common-mode range (typically -7 V to +12 V), allowing reliable communication in installations with large ground-potential differences. Internal slew-rate control and low bus-current loading support PROFIBUS, DMX512, and similar multi-drop protocols at 20 Mbps without external components. Typical applications include industrial field-bus nodes, motor encoder feedback links, building-automation gateways, solar inverter monitoring, and point-to-point backplane links between 3.3-V controllers. The wide common-mode range and IEC-grade ESD simplify compliance with industrial EMC requirements without external TVS arrays. When designing with this device, place the 100 nF VCC bypass capacitor as close to pin 10 as possible and use 120 Ω termination only at the two physical ends of the bus. Leave the middle of the bus unterminated to avoid loading reflections. The DE and RE pins let the host power-gate the part in sleep-mode designs by de-asserting both enables. This page synthesizes distributor pricing, drop-in alternatives from the TI SN65HVD7x family and cross-brand RS-485 ICs in the VSSOP-10 footprint, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
SN65HVD74D - 3.3V 20Mbps Full-Duplex RS-485 | TI
SN65HVD74D

SN65HVD74D - 3.3V 20Mbps Full-Duplex RS-485 | TI

The Texas Instruments SN65HVD74D is a 3.3 V full-duplex RS-485 transceiver with a 20 Mbps data rate, 12 kV IEC ESD protection, and an 8-pin SOIC package. It combines one differential driver and one differential receiver, providing separate data paths for simultaneous bidirectional communication over an RS-485 bus. The device supports a 3.0 V to 3.6 V supply range and operates from -40°C to 125°C. A transceiver interface IC converts between digital logic signals and balanced differential bus signals. The SN65HVD74 belongs to the RS-485 transceiver category within interface ICs, interface semiconductors, and broader communication semiconductors. Its differential signaling improves noise immunity by comparing the voltage between two bus conductors rather than referencing one conductor to ground, making it suitable for industrial, building-automation, and communications equipment operating over longer cable runs. The SN65HVD74D combines a 20 Mbps maximum data rate with more than 30 kV HBM ESD protection and more than 12 kV IEC61000-4-2 contact-discharge protection. Receiver hysteresis is 70 mV, helping reject conducted differential noise and prevent unwanted output transitions. Separate driver and receiver input and output pins support full-duplex bus arrangements without sharing a single half-duplex direction-control path. The transceiver operates from a single 3.3 V power supply and supports both RS-485 and RS-422 interface applications. Its surface-mount SOIC package permits automated assembly, while the stated -40°C to 125°C operating range supports industrial equipment, data-acquisition systems, factory controls, and industrial communication equipment. Each driver and receiver has separate input and output pins, allowing transmit and receive paths to operate simultaneously. Typical applications include full-duplex RS-485 industrial networks, high-speed instrumentation links, factory automation equipment, building-control systems, and industrial data acquisition. In a typical circuit, the microcontroller-facing pins connect to digital logic, while the differential A, B, Y, and Z pins connect to the balanced bus through suitable termination and protection components. The 70 mV receiver hysteresis helps maintain reliable decisions in electrically noisy environments. When designing the interface, maintain compatible logic levels, observe recommended bus biasing and termination, and verify that the selected cable length and topology remain valid for 20 Mbps operation. Protection-device capacitance should be included when calculating edge rate and channel performance. The 3.3 V supply must remain within the specified 3.0 V to 3.6 V range, and system designers should check all logic thresholds against their controlling device. This page combines the manufacturer's key electrical and environmental ratings with practical interface-design guidance, packaging information, and a focused drop-in replacement assessment. It highlights where the SN65HVD74D fits within a 3.3 V full-duplex RS-485 design and the checks that matter when evaluating bus speed, ESD robustness, receiver noise immunity, and PCB implementation.

RFQ پەیوەندی
SN65HVD75D - 3.3V 20Mbps RS-485 Transceiver | Texas Instruments
SN65HVD75D

SN65HVD75D - 3.3V 20Mbps RS-485 Transceiver | Texas Instruments

Texas Instruments SN65HVD75D is a 3.3 V half-duplex RS-485 transceiver with IEC ESD protection and a maximum signaling rate of 20 Mbps, housed in an 8-pin SOIC package. It supports operation from -40°C to 125°C and accepts 5 V-tolerant logic inputs compatible with 3.3 V or 5 V controllers. An RS-485 transceiver is an interface IC that combines a differential line driver and differential receiver, allowing digital data to be transmitted reliably over balanced, multipoint communication buses. The SN65HVD75 belongs to the transceiver hierarchy of interface ICs, differential line-driver and receiver circuits, and industrial communication semiconductors. Its half-duplex configuration permits a shared pair of conductors to carry data in either direction, but only one direction at a time. The SN65HVD75D operates from a 3.3 V supply, reaches 20 Mbps, and provides IEC ESD protection on the bus pins. Its logic interface supports 3.3 V and 5 V controllers, which simplifies connection to mixed-voltage digital systems. The wide -40°C to 125°C temperature range also makes the device suitable for industrial environments where commercial-temperature interface ICs may be inadequate. Exact ESD ratings, receiver thresholds, and electrical limits must be confirmed in the manufacturer datasheet. Each device combines a differential driver and differential receiver operating from one 3.3 V power supply. The bus pins are designed for robust ESD-event handling, including Human Body Model and IEC Contact Discharge protection. The manufacturer datasheet also identifies 250 kbps, 20 Mbps, and 50 Mbps signaling-rate options across the SN65HVD7x family, with 20 Mbps specifically associated with the SN65HVD75. Typical uses include industrial automation controllers, factory data buses, industrial instrumentation, building automation, and communications equipment operating on RS-485 networks. Its 20 Mbps capability supports high-speed half-duplex links, while 5 V-tolerant logic inputs ease interfacing with both 3.3 V and 5 V controllers. The half-duplex arrangement also requires careful direction-control design because the driver and receiver share the same bus pair. When designing the circuit, place a 100 nF ceramic bypass capacitor close to the supply pins and use a 3.3 V source capable of supporting the transceiver's operating current. The manufacturer recommends the TPS76333 for a suitable 3.3 V supply and the SN6501 for isolated power-supply designs. Bus routing should minimize stubs and maintain controlled differential impedance. This page combines verified manufacturer and distributor information, transparent pricing-status notes, same-family replacement analysis, and practical RS-485 design guidance. It also distinguishes verified electrical facts from parameters that still require confirmation against the complete SN65HVD7x manufacturer datasheet.

RFQ پەیوەندی
SN65HVD76D - 50Mbps Full-Duplex RS-485 | Texas Instruments
SN65HVD76D

SN65HVD76D - 50Mbps Full-Duplex RS-485 | Texas Instruments

Texas Instruments SN65HVD76D is a 3.3 V full-duplex RS-485 transceiver with a 50 Mbps data rate, separate driver and receiver enables, and 12 kV IEC contact-discharge ESD protection. It is packaged as a 14-pin SOIC for surface-mount industrial and instrumentation systems. An RS-485 transceiver combines a differential line driver and differential receiver to communicate reliably over noisy, long-distance industrial buses. The SN65HVD76 family supports both RS-485 and RS-422 applications, while its full-duplex architecture provides simultaneous transmit and receive paths through separate differential pins. It operates from a single 3.3 V power rail, simplifying integration with 3.3 V controllers, sensors, gateways, and test equipment. The principal features include a 50 Mbps maximum data rate, 1/8 unit-load receiver operation for up to 256 nodes, a 70 mV receiver hysteresis, and separate enable controls. According to the Texas Instruments product page, the driver enable is active high and the receiver enable is active low. Disabling both functions can reduce standby current to less than 5 uA, making the device useful in low-power distributed systems. Bus protection includes greater than 30 kV human-body-model protection and greater than 12 kV IEC 61000-4-2 contact-discharge protection, together with greater than 4 kV IEC 61000-4-4 fast-transient burst protection. These ratings help protect the transceiver in electrically noisy environments, although they do not eliminate the need for correct common-mode grounding, cable selection, and termination practices. Typical applications include industrial RS-485 links, factory automation equipment, building controls, instrumentation, and high-speed data acquisition. Full-duplex operation is particularly appropriate when continuous receiving is required while the controller also transmits status, configuration, or diagnostic data. The 14-pin SOIC format also supports conventional surface-mount assembly and thermal design. For a new layout, place the transceiver and its protection or bypass components near the bus connector, maintain a continuous ground reference with the cable, and apply termination only where required by the network topology. Verify that the selected logic controller can tolerate the receiver output levels and that the bus does not exceed the device's electrical limits. This page combines the exact device specifications, practical RS-485 design guidance, application fit, and package-level comparison information. It also distinguishes true board-level drop-in options from related family members whose enable behavior or transceiver configuration differs, helping engineers avoid selecting a substitute that requires schematic or layout changes.

RFQ پەیوەندی
SN65HVD77D - 3.3V 50Mbps Full-Duplex RS-485 | Texas Instruments
SN65HVD77D

SN65HVD77D - 3.3V 50Mbps Full-Duplex RS-485 | Texas Instruments

Texas Instruments SN65HVD77D is a 3.3 V full-duplex RS-485 transceiver with a 50 Mbps data rate, ±12 kV IEC ESD protection, and an 8-pin SOIC package. It combines one differential driver and one differential receiver in a single package, allowing transmit and receive paths to operate simultaneously. The device operates from 3.0 V to 3.6 V and is specified across -40°C to 125°C. An RS-485 transceiver is an interface IC that converts logic-level signals into differential bus signals and converts received differential signals back into logic levels. RS-485 belongs to the differential data-interface hierarchy, where the voltage between the A and Y conductors carries the signal while common-mode noise is rejected. The SN65HVD77D is designed for robust, point-to-point, multidrop, and full-duplex industrial communication links. The primary feature of the SN65HVD77D is its 50 Mbps signaling capability, making it suitable for high-speed data acquisition, factory automation, industrial control, and communications equipment. Its ±12 kV IEC-rated ESD protection improves system resilience when cables connect the transceiver to external equipment. Operating from a 3.3 V rail also simplifies integration with 3.3 V controllers, FPGAs, DSPs, and other digital logic. Each device contains separate driver and receiver inputs and outputs, eliminating the shared bus direction controls commonly found on half-duplex transceivers. Full-duplex operation allows data to be transmitted and received at the same time. The transmitter drives a differential pair, while the receiver provides a complementary logic-level output. Because there are no external enable controls, the device is intended for continuous enabled operation rather than controlled low-power bus shutdown. Typical implementations connect the logic-side data pins to a communications controller, connect the A and Y pins to a protected twisted-pair bus, and place the receiver output in the controller's receive path. Full-duplex systems use separate differential pairs for transmission and reception. The SOIC-8 package supports conventional surface-mount assembly and is suitable for industrial control boards, test equipment, motor-control systems, and embedded communications modules. The principal design consideration is signal integrity. High-speed differential routing requires controlled impedance, a continuous return path, minimized stubs, and proper termination at the bus endpoints. External protection may still be required for severe industrial transients because the integrated ESD rating addresses electrostatic discharge rather than every surge or lightning event. This product page combines the manufacturer's principal electrical and environmental specifications with same-package transceiver options, application guidance, and practical PCB-layout considerations. These engineering details help simplify device selection, footprint verification, and robust RS-485 implementation.

RFQ پەیوەندی