Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
CY7C68320-56LFXC - USB 2.0 ATA Bridge | Cypress
The Cypress Semiconductor CY7C68320-56LFXC is a USB 2.0 to ATA/ATAPI bridge controller with a 480 Mbps host interface, supplied in a 56-VFQFN package measuring 8 mm by 8 mm with an exposed pad. It is designed for systems that require an internal mass-storage connection between a USB host and an ATA or ATAPI device. The verified distributor information identifies the device as a USB Bridge with a USB 2.0 ATA interface and describes the original package as 56-VFQFN with an exposed pad. A USB-to-ATA bridge is an interface controller that translates USB traffic into the command, data, and status protocols expected by conventional storage devices. In the product hierarchy, this device is a USB interface IC, a USB-to-ATA bridge controller, and ultimately a semiconductor designed to reduce the host-controller burden of supporting legacy mass-storage peripherals. The bridge can therefore support storage-oriented equipment where an external USB connection must coexist with an internal ATA-style storage subsystem. The CY7C68320-56LFXC operates as a USB 2.0 high-speed peripheral-side controller at the stated 480 Mbps interface rate. Its 56-VFQFN package provides a compact surface-mount solution for densely populated embedded and industrial equipment. The exposed pad is an important thermal and electrical feature because it provides a direct connection between the device and the PCB copper beneath the package, subject to the manufacturer’s recommended land pattern and assembly requirements. The exact clocking, supply-voltage, current-consumption, operating-temperature, logic-level, and internal-controller details are not included in the supplied verified extracts and therefore cannot be stated reliably here. Designers should use the manufacturer datasheet for electrical limits, signal timing, ATA/ATAPI protocol details, oscillator requirements, and the complete exposed-pad layout. The verified material also contains closely related CY7C68320C-56LFXC and CY7C68321-56LFXC records, but those records should not be treated as identical without an engineering review of their respective datasheets and ordering information. Typical applications include industrial storage equipment, embedded data-acquisition systems, legacy computer peripherals, external-storage enclosures, and service or diagnostic systems that need a USB 2.0 bridge to an ATA/ATAPI device. The 480 Mbps USB interface offers materially greater headroom than the earlier USB 1.1 full-speed rate of 12 Mbps, while the dedicated ATA/ATAPI function avoids implementing that storage protocol directly in a host processor. PCB implementation should follow the exact exposed-pad land pattern and pin-assignment drawing in the manufacturer datasheet. The exposed pad should be connected to the appropriate supply or ground plane indicated by that drawing, with adequate via and copper area for thermal and electrical performance. Signal-routing and platform-interface details require verification because the supplied data does not include the complete pinout, recommended capacitors, or USB routing guidance. This page combines the verified distributor descriptions, package identification, availability information, source links, and qualified replacement data to support component discovery. It also distinguishes documented facts from fields requiring datasheet confirmation and avoids presenting unverified electrical claims as production specifications.
CY7C68320C-100AXA - USB 2.0 ATA Bridge | Infineon
The Infineon Technologies CY7C68320C-100AXA is a 3.3 V USB 2.0-to-ATA/ATAPI interface controller used to connect a USB host to an IDE storage device. It is identified as an EZ-USB AT2LP USB 2.0 ATA bridge and belongs to the broader line and bus controller category. The component is listed in a 100-pin TQFP package measuring 14 x 14 mm, providing a high pin count for host, storage, control, and auxiliary interface connections. A USB-to-ATA bridge is a specialized interface IC that translates USB transactions into ATA and ATAPI commands. This capability allows legacy parallel storage equipment to operate through a USB connection without redesigning the storage subsystem. The device therefore belongs to the hierarchy of USB interface controllers, peripheral interface ICs, interface adapters, and general-purpose semiconductors used in data-transfer and storage applications. The CY7C68320C-100AXA operates from a 3.3 V supply and supports full-speed and high-speed USB 2.0 operation. Its ATA/ATAPI side provides the command and data interface expected by compatible storage devices, while the USB side manages enumeration and data transfer with a USB host. The 100-pin TQFP package offers ample routing capacity for signal, control, power, and interface functions in systems that require a dedicated USB storage interface rather than a simpler general-purpose USB-to-serial converter. Typical uses include USB-connected external storage, industrial data acquisition systems, kiosk peripherals, legacy equipment modernization, and embedded systems that need to expose an ATA device through USB. The controller can also be considered for service and recovery equipment intended to read, initialize, or diagnose ATA-compatible media. Implementation requires careful USB signal routing, controlled 3.3 V power delivery, and firmware or operating-system support for the selected USB mass-storage behavior. Designers should verify the complete pin assignment, supported ATA device modes, USB enumeration behavior, and required external components against the manufacturer datasheet before layout release. USB differential pairs should be routed as controlled-impedance, length-matched traces, while the ATA and ATAPI signals require adequate grounding and short return paths. Power sequencing and signal-integrity margins are especially important when the bridge is placed between a host connector and external storage media. This page consolidates the exact package, voltage, interface, temperature, and sourcing details for CY7C68320C-100AXA with engineering-focused implementation guidance, commercial information, and a clear explanation of replacement-part verification requirements.
CY7C68320C-100AXC USB 2.0 ATA Bridge | Infineon Technologies
The Infineon Technologies CY7C68320C-100AXC is a USB 2.0 to ATA and ATAPI interface controller in a 100-lead TQFP package measuring 14 mm by 20 mm. The device operates from a 3.3 V supply, supports a commercial temperature range of 0 °C to 70 °C, and is designed for USB high-speed peripheral storage applications. A USB-to-ATA bridge is an interface controller that translates USB transactions into ATA or ATAPI commands for storage peripherals. It belongs to the USB interface controller family, where USB host connectivity is paired with an embedded storage interface. This bridging function allows a USB port to operate with compatible disk, tape, or removable-media equipment while preserving the established ATA command set. The CY7C68320C-100AXC provides a USB 2.0 high-speed peripheral interface, ATA interfacing, a 3.3 V supply requirement, and a 100-pin surface-mount package. Its commercial operating range covers 0 °C to 70 °C, making it appropriate for equipment intended to operate in controlled indoor or industrial-enclosure environments. The 14 mm by 20 mm TQFP format provides enough external pins for host, storage-side, clock, control, and power connections. The controller is used as the protocol-conversion element between a USB system and an ATA-compatible peripheral. Signal integrity at the USB and ATA edges depends on correct impedance-controlled routing, continuous return paths, and placement of the required decoupling capacitors. Its 100-pin package leaves sufficient perimeter space for fanout into these two interfaces, but the relatively large footprint must be considered when compact equipment designs are compared with smaller controller packages. Typical implementations include USB storage adapters, removable cartridge readers, embedded disk systems, legacy-portable-computer peripherals, and industrial data-acquisition equipment that retains an ATA interface. In these systems, the CY7C68320C-100AXC handles USB traffic and converts it into the appropriate ATA or ATAPI command sequence while the attached storage device supplies the physical data storage. PCB design should prioritize short USB differential traces, controlled impedance, solid ground-plane continuity, and decoupling close to the supply pins. Because this controller bridges two high-speed digital domains, connector and trace geometry should avoid unnecessary stubs. Prototype layouts should also follow the pin-description table and reference circuitry in the manufacturer datasheet rather than inferring connections from the package outline. This page consolidates the controller identity, interface details, package information, replacement guidance, and application guidance into one engineering reference. It also highlights the trade-off between protocol versatility and package size, helping designers determine whether the 100-lead TQFP implementation meets the mechanical, environmental, and connectivity requirements of a USB storage system.
CY7C68320C-56LFXC - USB 2.0 ATA Bridge | Cypress
Cypress Semiconductor Corporation CY7C68320C-56LFXC is a USB 2.0 to ATA/ATAPI bridge controller in a 56-pin QFN package measuring 8 x 8 mm. The device belongs to the EZ-USB AT2LP family and is intended to bridge a USB 2.0 host interface with an ATA or ATAPI storage device. Its commercial-temperature operating range is 0°C to 70°C, and the cataloged package configuration includes an exposed pad and tray packaging. A USB-to-ATA bridge is an interface controller that translates USB host transactions into ATA commands and responses for compatible storage peripherals. This bridge controller belongs to the broader USB interface-controller, peripheral-interface, and semiconductor hierarchy. Its practical purpose is to simplify the host-side protocol conversion required when attaching an ATA-compatible disk, compact-flash interface, or related storage subsystem to a USB 2.0 system. The key documented characteristics are USB 2.0 host-side support, an ATA/ATAPI device interface, 56-QFN construction with an 8 x 8 mm body, and an exposed thermal pad. The exposed pad provides a direct thermal and electrical path from the controller to the PCB, making careful land-pattern and thermal-layout implementation important. The LFXC ordering form denotes the 56-pin QFN configuration, while the final C character identifies this cataloged revision. The CY7C68320C belongs to a controller family designed for storage-interface bridging rather than general-purpose signal conditioning or data acquisition. Its architecture places the USB interface, ATA interface, control logic, and associated I/O resources in one integrated package. This integration reduces the component count required to implement a USB storage adapter, provided the system also supports the required USB enumeration, storage protocol, power-management, and operating-system behavior. Typical uses include USB storage adapters, embedded data-acquisition equipment, industrial control systems, backup appliances, and legacy ATA equipment modernization. The device is particularly relevant where a new USB 2.0 host must communicate with an ATA or ATAPI peripheral already designed into the system. Its commercial temperature range of 0°C to 70°C suits equipment expected to operate in controlled indoor environments rather than exposed automotive or extreme industrial installations. The primary PCB-design consideration is the exposed-pad thermal path. Place the device according to the manufacturer land pattern, provide solder paste coverage for the exposed pad, and use an uninterrupted ground or thermal plane beneath the package. Validate the completed assembly for adequate heat spreading under the maximum expected ATA, USB, and auxiliary interface activity before applying it to a new design. This product record combines the manufacturer-family description, package information, lifecycle classification, sourcing context, and practical implementation considerations into one engineering reference. It also distinguishes true same-package bridge alternatives from broad functional equivalents, helping designers identify candidates that still require pin, firmware, protocol, and timing verification before replacement.
CY7C68320C-56LTXC - USB 2.0 ATA Bridge | Infineon
Infineon Technologies CY7C68320C-56LTXC is a USB 2.0 to ATA/ATAPI bridge controller packaged in a 56-QFN package measuring 8 mm by 8 mm. The device belongs to the EZ-USB AT2LP HS-USB controller family and provides the interface conversion needed between a USB 2.0 host connection and an ATA or ATAPI storage device. Its principal application is bridging USB storage equipment without requiring a conventional host-side ATA controller in the system. A USB bridge is a type of interface controller that translates USB commands and data transfers into the command set expected by an ATA peripheral. In the broader hierarchy, it is an interface controller, a specialized integrated circuit, and ultimately a semiconductor used to connect host computers or embedded systems with storage peripherals. The USB-to-ATA arrangement supports portable storage, industrial equipment, data acquisition systems, and other applications requiring a computer-accessible disk interface. The CY7C68320C-56LTXC combines a high-speed USB interface with an ATA/ATAPI interface in one compact surface-mount package. Its USB 2.0 designation identifies the high-speed peripheral-side USB standard implemented by the controller, while the ATA/ATAPI side connects to compatible storage devices through the parallel ATA command and data interface. Consolidation of these functions reduces the number of separate interface components required in a storage subsystem. The 56-QFN package is designed for compact printed-circuit-board assemblies and provides a high pin count for the combined USB, ATA, data, control, power, and ground connections. The exposed-pad package construction described for this part supports heat transfer through the PCB copper area. Exact pin assignments, voltage ratings, timing limits, current requirements, operating-temperature limits, and electrical characteristics should be taken from the manufacturer datasheet before schematic or layout release. Typical applications include USB-connected external storage, embedded disk systems, industrial data loggers, test equipment, and legacy ATA peripherals connected to modern USB hosts. The bridge is particularly relevant when an equipment design must preserve an ATA storage interface while presenting a USB 2.0 connector to the external system. Firmware, operating-system compatibility, media-command behavior, and power-management requirements remain important system-level considerations. For PCB design, route the high-speed USB differential pair as a controlled-impedance differential pair and provide the decoupling, return-path, and grounding arrangements required by the manufacturer layout guidance. ATA signals are not a high-speed differential interface, but their length, timing margin, crosstalk, and connector-routing constraints still require deliberate layout planning. The exposed thermal pad should be connected to the appropriate ground plane and stitched according to the package drawing. This product overview combines interface classification, package information, application guidance, and design-focused selection criteria. It highlights how the USB 2.0 to ATA/ATAPI bridge function supports storage integration while keeping the implementation aligned with the device's 56-QFN footprint, USB routing requirements, and ATA signal-integrity constraints.
CY7C68320C-56PVXC USB 2.0 to ATA/ATAPI Bridge | Infineon
The Infineon Technologies CY7C68320C-56PVXC is the EZ-USB AT2LP USB 2.0 to ATA/ATAPI bridge controller, a dedicated interface IC that translates USB 2.0 traffic into ATA/ATAPI commands for a single CompactFlash or hard-disk device, operating at a 56 MHz internal clock in a 56-pin SSOP package. What is a USB-to-ATA bridge? A USB storage bridge sits in the hierarchy of USB interface controllers and mass-storage adapters, converting a host USB port into an ATA/ATAPI device-side bus. Without such a bridge, a USB port cannot talk directly to an IDE disk, so the controller must generate ATA command timing, data strobes, and drive the 40/80-wire parallel ATA cable while presenting a standard USB mass-storage device class to the host. The AT2LP architecture places a low-power microcontroller core inside the bridge, which allows protocol handling and board-level manufacturing test to be performed entirely through the USB interface without external equipment. Key features include support for CompactFlash plus one ATA/ATAPI device, full-speed/high-speed USB 2.0 peripheral operation, a Hi-Z ATA interface that can be placed in a high-impedance state so the ATA bus can be shared with another controller such as an IEEE-1394 device, and board-level manufacturing test using the USB interface. Package options in this family include SSOP and LQFP, with the -56PVXC ordering code identifying the 56-pin SSOP, commercial-temperature configuration. Typical applications include legacy IDE and CompactFlash storage adapters, industrial and in-flight entertainment data recorders, USB-to-IDE dongles, multi-format card readers, and legacy PC or embedded platforms that retain an ATA bus but need a modern USB 2.0 host connection. Because the ATA side is a parallel bus, board layout must keep the ATA traces short and properly terminated, and USB differential routing must follow controlled-impedance layout rules. When designing with this device, confirm that the USB host supplies the bus voltage needed for the attached ATA drive, provide the required USB transceiver and passives from the reference schematic, and verify that the ATA cable length stays within the limits stated in the manufacturer datasheet. This page consolidates distributor availability, drop-in alternatives, pin and package guidance, and practical design notes for engineers who need to source or replace this legacy-to-modern storage interface bridge.
CY7C68321-100AXC USB 2.0 ATA Bridge | Cypress
The Cypress Semiconductor CY7C68321-100AXC is a fixed-function EZ-USB AT2LP USB 2.0 to ATA/ATAPI bridge integrated circuit in a 100-pin TQFP package. It provides one USB port and support for one or two ATA- or ATAPI-based devices, including CompactFlash storage, while offering an ATA interface high-impedance mode for shared-bus designs. The device is identified in the verified distributor data as a USB Bridge with a USB 2.0 ATA interface and a 100-TQFP (14 x 20 mm) package. The CY7C68321 belongs to the EZ-USB AT2LP family of USB storage interface controllers. An interface IC is a semiconductor category used to connect host buses and peripheral protocols; in this case, the bridge translates the USB 2.0 host interface into ATA/ATAPI signals used by compatible storage devices. Its position within the broader hierarchy is interface IC, then USB interface controller, then fixed-function USB-to-ATA bridge. Verified listing information identifies the part as a 480 Mbps USB 2.0 interface solution with a 3.15 V minimum and 3.45 V maximum operating voltage. The ATA side can support CompactFlash and one ATA/ATAPI device. Its high-impedance ATA interface is useful when another controller, such as an IEEE 1394 device, must share the ATA bus. These details make the bridge relevant to legacy USB storage appliances, embedded ATA systems, and CompactFlash equipment. The 100-pin TQFP package provides the board interface required for host, storage, power, control, and signal-conditioning connections. Because this legacy bridge targets USB 2.0 and ATA/ATAPI rather than modern USB storage standards, designers should verify host operating-system support, device compatibility, signal integrity, power sequencing, and connector requirements before releasing a new design. The verified distributor pages do not publish detailed timing, thermal, or environmental values, so those parameters remain to be confirmed from the manufacturer datasheet. This page consolidates the verified product identity, package information, sourcing links, interface capability, and engineering selection criteria. It also distinguishes confirmed facts from parameters that require datasheet verification, helping engineers evaluate the CY7C68321-100AXC without treating catalog snippets as a complete electrical specification. Designs should reserve adequate placement and routing flexibility for the 100-pin TQFP footprint, validate the ATA and USB signal-integrity requirements, and confirm device-support policy before production. For a new USB-to-ATA product, assess whether a modern USB mass-storage controller provides better long-term platform support. For maintaining an existing ATA/CompactFlash design, the bridge may remain suitable if its timing, power, and compatibility requirements are unchanged.
CY7C68321-56LFXC - USB 2.0 to ATA Bridge | Infineon
The Infineon Technologies CY7C68321-56LFXC is a USB bus controller and USB 2.0-to-ATA interface bridge designed to connect USB storage equipment with ATA or ATAPI devices. It is a CMOS integrated circuit supplied in a 56-QFN package measuring 8 mm by 8 mm. The controller bridges the USB 2.0 host interface and ATA storage interface, supporting the transfer of data between a USB-equipped computer and ATA-based mass-storage systems. A USB-to-ATA bridge is an interface controller within the broader USB interface IC category. It translates USB traffic and ATA storage commands so that a legacy ATA device can appear as a USB peripheral without requiring a host-side protocol converter to understand the ATA command set. This function places the CY7C68321-56LFXC in the storage-controller hierarchy: USB interface controller, mass-storage bridge, ATA/ATAPI interface controller, and ultimately a CMOS semiconductor. The verified distributor information identifies the device as a USB Bridge with a USB 2.0 ATA interface in a 56-QFN (8x8) package. Its EZ-USB AT2LP family designation is also visible in distributor listings for the same MPN. The compact 56-QFN package supports space-constrained external storage, portable media, docking, and embedded USB storage designs where a larger through-hole or leaded bridge package would be undesirable. The CY7C68321-56LFXC belongs to a family of related controllers including CY7C68321C-56LFXC, CY7C68300C-56LFXC, and CY7C68300B-56LFXC. The C suffix identifies different family revisions or ordering variants, but the supplied web data does not expose a verified electrical comparison table, operating-voltage range, or USB speed difference for each suffix. Engineers should therefore confirm the complete datasheet and firmware requirements before treating a related suffix as a drop-in substitution. A key design consideration is that the device is a protocol bridge rather than a general-purpose USB host controller. The surrounding board must provide compliant USB 2.0 signal routing, ATA power management, storage-side connectivity, and the decoupling appropriate for its supply rails. USB differential-pair routing, ATA signal integrity, and the exposed-pad grounding arrangement of the QFN package require close attention in multilayer PCB layouts. Typical implementation roles include an ATA flash-memory reader, a USB storage adapter, a portable storage enclosure, and a compact embedded USB-to-disk interface. Because the verified data does not provide the operating voltage, transfer rate, temperature range, or absolute maximum ratings, those values must be taken directly from the applicable manufacturer datasheet before schematic sign-off. This page consolidates verified distributor listings, related family members, package information, and application-specific engineering guidance. It adds selection context and design notes beyond the basic catalog description while clearly separating verified facts from parameters that still require manufacturer documentation.
CY7C68321C-100AXC - USB 2.0 ATA Bridge | Cypress
The Cypress Semiconductor CY7C68321C-100AXC is an EZ-USB AT2LP USB 2.0 to ATA/ATAPI bridge controller designed for storage peripherals and USB-to-ATA interface designs. The device supports USB 2.0 high-speed operation, one ATA or ATAPI device, Compact Flash support, board-level manufacturing test through the USB interface, and a high-impedance ATA interface mode for sharing the ATA bus with another controller such as an IEEE-1394 controller. The component is specified in a 100-pin LQFP package and operates from a 3.15 V to 3.45 V supply range. A USB-to-ATA bridge is an interface controller that translates USB host transactions into ATA or ATAPI commands for storage devices. The CY7C68321C-100AXC sits between a USB system and an ATA storage bus, providing protocol bridging rather than operating as a general-purpose microcontroller or storage device itself. Its USB 2.0 interface makes it suitable for legacy and embedded systems requiring a host-side connection to IDE or compatible storage peripherals. The main functional features include support for Compact Flash and one ATA or ATAPI device, support for board-level manufacturing testing through USB, and an ATA interface high-impedance state. The high-impedance capability is useful in multi-controller systems because it can electrically isolate the ATA bus while another controller, including an IEEE-1394 controller, is active. This feature helps reduce bus contention and supports controlled ownership of the shared storage interface. The CY7C68321C-100AXC is identified by the verified manufacturer and distributor listings as an EZ-USB AT2LP USB 2.0 to ATA/ATAPI bridge in a 100-LQFP package, with an operating temperature range of 0 °C to 70 °C and a 3.15 V to 3.45 V operating supply range. The product is listed as obsolete or end-of-life in the available product information, so new designs should verify lifecycle status and consider a redesign or an explicitly qualified replacement rather than assuming a current production commitment. Typical applications include USB-to-IDE storage adapters, embedded data acquisition systems with legacy ATA storage, Compact Flash equipment, board-level production test systems, and shared ATA-bus designs involving more than one storage controller. For new USB storage products, the design should account for the legacy ATA electrical interface and verify the bridge firmware, cable, connector, power, and operating-system compatibility. The verified information identifies the package and core interface functions, while a complete pin description, electrical timing details, and a manufacturer application reference should be confirmed in the official device documentation before layout release.
CY7C68321C-56LFXC - USB 2.0 to ATA Bridge | Infineon
The Infineon Technologies CY7C68321C-56LFXC is a USB 2.0 to ATA/ATAPI bridge controller based on the EZ-USB AT2LP architecture, with USB high-speed peripheral connectivity, CompactFlash support, and a 56-pin VQFN package measuring 8 x 8 mm. The device bridges USB storage traffic to an ATA or ATAPI interface while providing board-level manufacturing-test support through its USB interface. A USB-to-ATA bridge is an interface controller that translates commands and data between a USB host and an ATA-compatible storage device. Within the broader hierarchy, it is a USB interface IC, peripheral controller, storage-interface bridge, and semiconductor. Its principal design role is to allow a USB-equipped computer or embedded system to communicate with an ATA or ATAPI peripheral without implementing the complete protocol conversion in system firmware or external logic. Key features include support for CompactFlash and one ATA or ATAPI device, USB 2.0 operation, and a manufacturing-test mode accessible through the USB interface. The controller can place its ATA interface in a high-impedance state, allowing the ATA bus to be shared with another controller such as an IEEE-1394 controller. This bus-isolation capability is valuable in systems that need to transfer ownership of the storage bus between interfaces. The 56-VQFN arrangement supports compact integration in storage adapters, dock equipment, portable media systems, and industrial data-acquisition products. Its surface-mount construction reduces board area compared with a larger leaded package, although exposed-pad thermal management and careful high-speed USB layout remain important. The C suffix identifies the specific ordered device configuration, while the 56 suffix identifies its 56-pin package configuration. Typical applications include USB-to-CompactFlash readers, ATA storage adapters, industrial removable-media systems, manufacturing-test fixtures, and legacy equipment that adds a USB storage interface. In each case, the bridge consolidates protocol conversion in a dedicated controller and leaves the host software with a standard USB storage interface. Designers should follow the manufacturer datasheet when assigning the 56-pin footprint, USB routing, ATA or ATAPI traces, power rails, decoupling capacitors, and exposed-pad connections. USB differential routing and the ATA interface require controlled impedance and short return paths, while adequate input and output bypassing helps prevent conducted noise from disturbing attached storage devices. This page combines the documented bridge features, package information, compatible family references, comparison data, and practical integration guidance into a focused engineering resource for USB-to-ATA storage designs.
CY7C68321C-56LTXC - USB 2.0 ATA Bridge | Infineon
The Infineon Technologies CY7C68321C-56LTXC is a USB 2.0 to ATA/ATAPI bridge controller with a maximum operating frequency of 24 MHz, support for 12 Mb/s and 480 Mb/s USB data rates, and a 56-pin QFN exposed-pad package. The device is designed to bridge USB storage traffic to an ATA or ATAPI peripheral interface while supporting full-speed and high-speed USB operation. A USB-to-ATA bridge is an interface controller that lets a USB host communicate with storage hardware that uses the parallel ATA/ATAPI command and data interface. Within the product hierarchy, the CY7C68321C is a USB interface transceiver and protocol bridge, placing it between USB host controllers and conventional storage peripherals. Its role is to translate USB transactions into compatible ATA/ATAPI operations rather than regulate power or perform storage computation. Key characteristics include full-speed and high-speed USB operation, a 12 Mb/s low-speed connection rate, a 480 Mb/s high-speed connection rate, and operation from 0°C to 70°C. The non-lead-frame QFN package provides a surface-mount implementation for compact storage peripherals, dongles, and embedded USB storage equipment. The exposed pad supports thermal conduction from the device into the PCB copper area. The interface architecture makes the CY7C68321C-56LTXC suitable for systems where an embedded storage device must appear as a USB peripheral. Its 24 MHz maximum operating frequency accommodates USB traffic handling and associated interface timing, while the dedicated bridge function reduces the need for an external USB-to-ATA controller. System designers should still validate protocol timing, media compatibility, and power requirements during prototype testing. Typical implementations include USB-connected removable storage, industrial data-collection equipment, compact embedded storage modules, legacy peripheral upgrade systems, and USB storage adapters. The part is particularly relevant where a board design requires a direct USB-to-ATA interface rather than a general-purpose USB hub or a bridge based on a different storage protocol. PCB layout is critical around high-speed USB and exposed-pad thermal connections. Place the USB differential pair as a short impedance-controlled route, provide the decoupling specified by the manufacturer datasheet, and connect the exposed pad to an uninterrupted ground-copper region. Validate USB eye diagrams, enumeration behavior, ATA signal integrity, and enclosure or cable reliability in the final system. This page combines the USB interface, package, temperature, and speed characteristics of the CY7C68321C-56LTXC with application guidance, comparison criteria, and practical replacement considerations. It also identifies where design validation is still required, including exact pin assignments, lifecycle status, environmental qualifications, and protocol-level compatibility of candidate replacements.
CY8C20110-SX2I - 10-Input CapSense Controller | Infineon
The Infineon Technologies CY8C20110-SX2I is a CapSense Express touch-sensing controller with 10 configurable CapSense I/O pins, support for 4 to 10 capacitive buttons, and an I2C control interface in a 16-pin SOIC package. It operates from a 2.4 V to 2.9 V supply and is specified for ambient temperatures from -40°C to 85°C. A capacitive touch controller is a specialized input interface IC that detects changes in capacitance caused by a user's finger or conductive object. It belongs to the broader capacitive-sensing controller category, which combines analog front-end measurement, configurable button logic, and digital communication. Unlike a mechanical switch, a CapSense controller can provide sealed user interfaces, compact layouts, and configurable behavior without exposing moving electrical contacts. The CY8C20110 supports four to ten capacitive buttons through its 10 CapSense I/O resources. Its I2C interface provides a straightforward connection to a host microcontroller for configuration and status communication. Configuration is stored in onboard nonvolatile memory so that the controller can load its operating configuration automatically at power-on. The device is also optimized for LED dimming in backlight applications through 15 selectable duty cycles. The CY8C20110-SX2I combines sensing and control functions without requiring a separate host processor to perform basic touch detection. Its operating range of 2.4 V to 2.9 V suits low-voltage embedded systems where supply headroom is constrained. The industrial temperature rating of -40°C to 85°C supports operation across commercial and industrial ambient environments when the complete assembly is designed and tested for those conditions. Typical uses include appliance control panels, compact capacitive keypads, lighting controls, backlight dimming interfaces, and embedded touch buttons. In a keypad, multiple CY8C20110 I/O resources can support individual electrodes, while the host reads touch events over I2C. The device is particularly useful when the mechanical design requires a flush panel, sealed enclosure, or a product appearance based on illuminated capacitive controls rather than discrete switches. Designers should account for electrode geometry, guard components, environmental compensation, connector capacitance, and the effect of enclosure materials. The I2C bus must also be checked for address availability and pull-up requirements on the assembled system. Because the verified product information does not provide a complete public pin map, PCB designers should use the manufacturer pinout and reference design rather than infer connections from the package outline. This page combines verified manufacturer and distributor information, package and interface constraints, drop-in alternatives, application guidance, and design notes. It highlights where the CY8C20110-SX2I fits within capacitive user-interface designs and where replacement decisions require additional firmware, firmware-compatibility, and board-level validation.
CY8C20111-SX1I - One-Button Capacitive Touch | Infineon
The Infineon Technologies CY8C20111-SX1I is a CapSense Express capacitive-touch controller for one touch button, featuring one general-purpose output and I2C/2-Wire connectivity in an 8-SOIC package. It is designed for compact human-interface applications where a single touch target must be detected reliably without a mechanical switch. The verified product data identifies the device as an 8-pin SOIC capacitive-touch controller; detailed electrical ratings and timing values require the manufacturer datasheet. A capacitive-touch controller is an integrated circuit that measures changes in capacitance caused by a conductive surface, typically a copper button or pad, and converts that change into a digital output. The CY8C20111 belongs to the broader hierarchy of capacitive sensing integrated circuits, touch controllers, interface controllers, and embedded mixed-signal semiconductors. CapSense controllers are useful in appliance controls, access panels, medical equipment, and industrial interfaces where sealed or low-profile controls are preferred. The verified listing identifies the CY8C20111 as the one-button member of the CapSense Express family. The same source states that CY8C20121 supports two capacitive sensing buttons and two general-purpose outputs, while CY8C20111 supports one capacitive sensing button and one general-purpose output. This distinction is important when comparing the devices: the one-button CY8C20111 may be the simpler choice for a single touch zone, whereas CY8C20121 provides additional sensing and output resources. The I2C/2-Wire interface allows the controller to participate in a host-controlled embedded system rather than operating as a completely independent user interface. Designers should confirm host address, serial timing, pull-up requirements, firmware behavior, and electrical limits against the manufacturer datasheet before finalizing the interface. The 8-SOIC package supports conventional surface-mount assembly, although the verified material does not provide dimensions or pin numbering. Typical use cases include touch panels for household appliances, compact control modules, equipment front panels, and low-profile controls where a conventional mechanical switch would be undesirable. The capacitive sensing electrode should be designed with the controller’s recommended layout, guarding, shield, and grounding techniques. Environmental factors such as moisture, nearby conductors, enclosure materials, and human-body loading can affect sensor performance. The CY8C20111-SX1I is best suited to designers seeking a dedicated one-button touch controller with serial connectivity in an established SOIC footprint. Before purchasing, verify current lifecycle status, pricing, availability, temperature range, supply voltage, operating current, output timing, and the exact pinout using the latest manufacturer documentation. This page combines verified distributor identification, package and interface information, source traceability, and application guidance. It does not infer electrical limits, pricing, pin names, or compliance claims that are absent from the supplied data.
CY8C20140-SX2I - 4-Key CapSense Controller | Infineon
The Infineon CY8C20140-SX2I is a CapSense Express capacitive-touch button controller with four configurable I/O inputs, a 3 V supply, and a 16-pin SOIC package. It combines capacitive sensing, GPIO functions, LED-driving capability, interrupt support, 2 kbit flash memory, and 512 bytes of RAM in one compact controller. The verified distributor listing identifies the device as a 16-SOIC capacitive-touch button controller, while an indexed datasheet excerpt describes configurable I/O for sensing buttons or driving LEDs and interrupts. A capacitive-touch controller is a semiconductor that detects changes in capacitance caused by a user touching an external conductive pad. In the broader hierarchy, the CY8C20140 belongs to capacitive sensing controllers, interface ICs, and embedded control devices. Its sensing algorithm is designed for high sensitivity and low noise, with claimed immunity to RF and AC noise and low radiated EMC noise. This makes it useful where physical buttons must remain reliable on sealed, compact, or cosmetic control surfaces. The device supports applications with four, six, eight, or ten capacitive inputs according to the verified product description, although the selected CY8C20140 listing is specifically categorized as a 16-SOIC part. Firmware and configuration are handled through an I2C interface, and configuration can be stored in onboard nonvolatile memory for automatic loading at power-on. The available data identifies 2 kbits of density and 2 KB of flash storage; these values are retained exactly as provided rather than inferred into unsupported detail. The controller is suitable for appliance control panels, access controls, audio equipment, industrial interfaces, and consumer products. A four-button panel can use the configurable I/O for sensing electrodes or auxiliary functions, while the host processor reads status and handles higher-level behavior. Designers should confirm the exact pin functions, electrical limits, configuration procedure, and application circuit from the manufacturer datasheet before layout or firmware release. PCB implementation requires careful sensor-electrode geometry, grounding, shielding, and separation from noisy switching nodes. The available verified excerpts emphasize broad support for sensor capacitance, sensor shapes, sensor sizes, and noise immunity, but do not provide enough data to state precise layout dimensions or timing values. Use the manufacturer guidance for those details rather than extrapolating from generic touch-controller layouts. This page consolidates distributor availability, manufacturer-oriented search results, indexed datasheet excerpts, and replacement research for CY8C20140-SX2I. The supplied evidence does not include a current unit price, complete pinout, or verified list of same-package substitutes; those gaps are explicitly marked instead of being filled with guesses.
CY8C20142-SX1I - 4-IO CapSense Controller | Infineon
The Infineon Technologies CY8C20142-SX1I is a CAPSENSE Express capacitive-touch button controller with 2.4 V to 5.5 V operating supply, four configurable GPIOs, and an 8-pin SOIC package. It combines capacitive sensing for external touch buttons with general-purpose GPIO functions for LED indication, interrupts, and related mixed-signal control tasks. The controller operates from -40°C to 85°C and supports I2C communication. A capacitive-touch controller is an interface IC that detects changes in capacitance caused by a user's finger and converts those analog changes into digital events. In the product hierarchy, this device is a CAPSENSE Express controller within the broader class of capacitive sensing controllers, interface ICs, and mixed-signal semiconductors. Its purpose is to replace discrete analog sensing networks with a configurable digital interface suitable for compact user-interface designs. Key features include four configurable I/O channels that can be used as capacitive-sensing inputs or GPIOs, a 2.4 V to 5.5 V supply range, and I2C connectivity. One verified distributor listing identifies 2 kbits of device memory, while another describes 512 bytes of RAM and PWM capability. The SOIC-8 package provides a compact surface-mount footprint, and the -40°C to 85°C range supports industrial-temperature designs. The device combines a small embedded controller with configurable sensing and GPIO resources. Its four channels can be allocated according to the interface requirements of the product, while the I2C interface allows a host microcontroller or system controller to configure and monitor touch events. Because it is a dedicated CapSense Express controller rather than a general-purpose MCU, it can reduce the sensing burden placed on the primary embedded processor. Typical applications include appliance control panels, industrial touch buttons, equipment interfaces, consumer products, and low-cost human-machine interfaces. A connected host can read button states over I2C, update LED indicators through selected GPIOs, and respond to user input without dedicating a separate analog front end to capacitance measurement. PCB layout is critical for reliable capacitive sensing. The sensing electrodes, their connecting traces, ground structures, and enclosure materials influence sensitivity and stability. Designers should follow the manufacturer's pinout and application guidance, keep sensitive routes short, provide a stable ground reference, and evaluate the complete mechanical and electrical environment rather than treating the controller as a conventional digital switch input. This page consolidates the verified manufacturer and distributor information for CY8C20142-SX1I and adds package-specific design guidance, parameter comparisons, and a same-family replacement analysis. The alternative assessment is intentionally conservative: only controllers documented as using the same package are treated as potential drop-in parts, and unsupported electrical details are marked as data needed rather than estimated.
CY8C20160-SX2I CapSense Touch Controller | Infineon
The Infineon CY8C20160-SX2I is a CapSense Express capacitive-touch controller with 16-SOIC packaging and six configurable I/O resources for capacitive sensing or general-purpose output functions. The verified distributor data identifies it as a capacitive-touch button controller, while the product family supports configurable capacitive-sensing buttons and GPIOs for driving LEDs or generating interrupts. It is associated with a 3 V supply voltage and an operating-temperature range of -40°C to 85°C. A capacitive-touch controller is a semiconductor that detects changes in capacitance caused by a user touching an electrode or sensor pad. In the broader hierarchy, the CY8C20160-SX2I belongs to the family of capacitive-sensing controllers, touch-screen controllers, embedded controllers, and integrated circuits. Unlike a mechanical switch, this controller can interpret capacitive input electronically and combine that function with programmable digital I/O in a compact surface-mount device. The primary feature is the integration of CapSense Express control with six I/O resources. According to the verified technical listing, the I/O can be configured as capacitive-sensing buttons or as GPIOs for driving LEDs or interrupts. This combination reduces the number of separate components required for a small user-interface panel because touch detection and immediate digital-output functions can coexist in one controller. The 16-SOIC package also supports conventional surface-mount PCB assembly. The device operates from a 3 V supply and is specified over -40°C to 85°C. These values place it in an industrial-temperature operating range suitable for embedded controls, access panels, appliances, and compact human-interface systems. The verified listing also associates the part with a 2 kbit data density, while another distributor specification reports 2 KB of flash and 512 bytes of RAM. These memory descriptions should be confirmed against the applicable manufacturer documentation before relying on them for firmware sizing. Typical uses include capacitive buttons for appliance controls, illuminated touch keys, compact access panels, and LED or interrupt-driven user interfaces. Because the I/O resources can serve both sensing and GPIO roles, the controller is especially useful when a design needs a limited number of touch inputs without adding a larger general-purpose microcontroller. Designers should confirm the exact pin mapping, usable I/O count, memory organization, and programming requirements from the manufacturer datasheet before layout release. PCB design must preserve the intended capacitive-sensing electrode geometry, provide suitable grounding and filtering around the controller, and account for connector, copper, and enclosure effects that can change touch performance. This page consolidates the verified distributor specifications, package information, commercial availability, candidate family alternatives, and practical design cautions. It also separates confirmed values from specification gaps, helping engineers evaluate sourcing and fit without treating search-result snippets as a substitute for the complete manufacturer datasheet.
CY8C20180-SX2I - CapSense Touch Controller | Infineon
The Infineon Technologies CY8C20180-SX2I is a CapSense Lite capacitive-touch controller with four configurable I/O channels, a 3 V supply, and an 8-pin SOIC package. It is designed for compact capacitive button interfaces, GPIO-driven indicators, and interrupt-capable control inputs. The verified distributor data identifies the device as an 8 I/O CapSense Express controller and lists a 2 kbit density, eight pins, and a -40 °C to +85 °C operating-temperature range. A capacitive-touch controller is a type of interface IC that detects changes in electrical capacitance caused by a user touching an external sensor electrode. In a knowledge-graph hierarchy, the CY8C20180-SX2I belongs to the CapSense controller family, interface ICs, and semiconductor devices. Its four configurable I/O resources can be assigned to capacitive-sensing buttons or used as GPIOs for driving LEDs or interrupt functions, allowing a small control panel to replace mechanical switches. The key verified features are four configurable I/O channels, capacitive sensing of up to four buttons, 3 V operation, 2 kbit density, eight-pin SOIC packaging, and an extended -40 °C to +85 °C temperature range. The distributor listing also identifies the part as an Infineon capacitive-touch button controller. Exact pin names, device-programming details, current consumption, and electrical timing limits were not included in the supplied source data and therefore are not inferred here. The CY8C20180-SX2I is suitable for low-voltage embedded user interfaces where a dedicated touch controller simplifies front-panel design. Its small SOIC footprint helps preserve board area in compact products, while configurable I/O supports shared sensing and general-purpose control requirements. The I2C-related functionality mentioned in comparison data should be verified against the manufacturer datasheet before final firmware and PCB sign-off. Typical applications include appliance control panels, small consumer products, industrial interface modules, LED status indicators, and embedded keypad or button assemblies. For a new design, confirm the exact sensor geometry, electrode size, grounding, shielding, and firmware configuration using the manufacturer application guidance. The -40 °C to +85 °C range makes the part suitable for industrial-temperature indoor products when the surrounding enclosure and connector system are also qualified. A practical design consideration is to keep capacitive-sensing traces short and keep the touch electrode away from high-current switching nodes and noisy sources. The controller does not eliminate the need for careful analog layout, filtering, calibration, and environmental tuning. This page synthesizes verified distributor specifications, replacement research, package information, and practical integration guidance while clearly separating missing datasheet details from confirmed values.
CY8C201A0-SX2I - 10-I/O CapSense Controller | Infineon
The Infineon Technologies CY8C201A0-SX2I is a CapSense Express capacitive-touch controller with 10 configurable I/Os, one slider, 2 kbits of onboard nonvolatile configuration memory, and a 16-pin SOIC package. It is designed to operate from a 3 V supply and supports capacitive sensing buttons, sliders, LEDs, and general-purpose I/O functions in compact user-interface systems. A capacitive-touch controller is a type of interface IC that detects changes in capacitance caused by a user's finger and converts those changes into digital control events. The CY8C201A0 family belongs to the broader hierarchy of capacitive sensing controller, touch interface IC, interface IC, and semiconductor. Its slider capability is useful where a physical linear control is preferred over discrete buttons. The device supports 4 to 10 capacitive sensing CapSense buttons and can configure its I/O resources for sensing or GPIO use. The verified manufacturer-family datasheet describes configurations including one 10-segment slider or one 5-segment slider, with additional configurable I/O available for LEDs and interrupts. Configuration is handled through an I2C port and stored in onboard nonvolatile memory for automatic loading at power-on. Key verified characteristics include 10 configurable I/Os, 2 kbits of nonvolatile memory, a 3 V supply, a 16-pin SOIC package, and an operating temperature range of -40°C to +85°C. Search results also identify 1.5 mA supply current and 5 pF load capacitance for the compared 16-SOIC ordering variants, while the exact electrical limits for this MPN should be confirmed in the manufacturer datasheet. Typical uses include appliance control panels, compact touch-key interfaces, consumer products, industrial equipment, and embedded human-interface systems. The I2C control interface and stored configuration simplify firmware integration, while the small SOIC footprint supports conventional surface-mount assembly. Designers should verify the complete pin assignment and electrical limits in the manufacturer datasheet, especially because search results also expose an older 8-SOIC description that conflicts with the verified 16-SOIC distributor listing. PCB designs should preserve the documented I2C pull-up arrangement and provide appropriate grounding and sensor-layout practices for stable capacitive measurements. This page consolidates verified distributor listings, manufacturer-family datasheet information, a strict drop-in alternative review, application guidance, and practical design notes. It is intended to help engineers evaluate procurement, compatibility, and implementation requirements without relying on a single retail listing.
CYPD3135-40LQXI - EZ-PD CCG3 USB-C PD Controller | Infineon
The Infineon CYPD3135-40LQXI is an ARM Cortex-M0 based EZ-PD CCG3 USB Type-C port controller supporting USB Power Delivery 3.0, packaged in a 40-pin UFQFN with exposed pad. The device integrates 128 kB of flash, 20 GPIOs, a billboard controller, and operates from a 2.7 V to 21.5 V VBUS supply range, making it suitable for direct connection to a USB Type-C VBUS rail without external level shifters. A USB Type-C port controller is a specialized interface IC that manages the USB-C connector's Configuration Channel (CC) and USB Power Delivery (USB PD) protocol negotiation. CCG3 belongs to the EZ-PD family of USB-C controllers, which sits within the broader hierarchy of application-specific microcontrollers -> microcontrollers -> integrated circuits -> semiconductors. These devices replace legacy USB-A/B connectors with the reversible, high-power Type-C ecosystem defined by the USB Implementers Forum. Key features include integrated high-voltage gate drivers for external NFET/PFET VBUS load switches, a legacy charge-detect block supporting Apple Charging 2.4 A, Qualcomm QC 4.0, and Samsung AFC protocols, hardware USB PD 3.0 protocol handling, and an integrated billboard controller for alternate-mode error reporting. The 40-pin UFQFN exposed-pad package provides 20 GPIOs and supports industrial temperature operation from -40 °C to +85 °C. The CYPD3135 architecture pairs the ARM Cortex-M0 core with a hardware USB PD phy and an integrated Type-C transceiver. Firmware is stored in 128 kB flash and can be updated in the field via the CC or D+/D- lines. The high-voltage gate driver outputs tolerate VBUS transients up to 21.5 V, eliminating external bootstrap or charge-pump circuitry. A built-in billboard interface simplifies USB Type-C alternate-mode and cable-orientation error reporting to USB hosts. Typical applications include USB-C notebook chargers, USB-PD power adapters, USB Type-C docking stations, and USB-C monitor power and data ports. The wide 2.7-21.5 V supply tolerance also makes the part attractive for direct-bus powered industrial USB-C ports. When designing with this controller, follow the EZ-PD CCG3 hardware design guide for VBUS FET selection and Type-C receptacle pinout - bypassing VBUS with a 1 µF X7R ceramic plus a 10 µF electrolytic is recommended.
CYPD3135-40LQXIES - EZ-PD CCG3 USB-C PD Controller | Infineon
The Infineon CYPD3135-40LQXIES is an EZ-PD CCG3 USB Type-C port controller and Power Delivery (PD) microcontroller in a 40-pin UFQFN exposed-pad package. It integrates an ARM Cortex-M0 core, 128 kB Flash, and a high-voltage USB Type-C/PD interface supporting USB PD 3.0 with legacy charge detection (Apple 2.4A, QC 4.0, Samsung AFC). The device operates from a 2.7 V to 21.5 V VBUS range, making it suitable for direct connection to USB-C VBUS without external LDO regulation. What is a USB Type-C port controller? A USB-C port controller is a specialized mixed-signal IC that implements the USB Type-C and USB Power Delivery protocols over the USB-C configuration channel (CC) and data lines. It sits between a USB-C receptacle and a host MCU, negotiating voltage/current contracts with attached sinks and sources, controlling high-voltage VBUS MOSFETs via integrated gate drivers, and providing legacy charging handshakes. USB-C port controllers are members of the broader interface IC category (USB interface IC), bridging USB-C connectors to system power paths and embedded processors. Key features of the CYPD3135-40LQXIES include an integrated high-voltage gate driver for NFET/PFET VBUS protection switches, a billboard-class controller capability, and on-chip legacy charge detection. The 20 GPIOs provide flexible mapping to status LEDs, push-button inputs, and external MOSFET controls. The 128 kB Flash supports USB PD 3.0 firmware with PPS (Programmable Power Supply) and HVDCP profiles. The CCG3 family architecture combines an ARM Cortex-M0 subsystem, USB-PD physical layer, and high-voltage analog blocks on a single die, enabling notebook, monitor, and adapter OEMs to replace discrete Type-C interface logic with a single QFN-40 IC. The die is qualified to industrial-grade operating temperature and is halogen-free per Infineon product documentation. Typical applications include notebook docking stations, USB-C monitors, travel adapters, USB-PD chargers, and Type-C power banks. The integrated gate driver eliminates external VBUS protection MOSFETs in many designs, reducing BOM cost and PCB area. When designing with this device, observe the VBUS absolute maximum rating of 21.5 V and ensure the exposed pad is soldered to a sufficiently sized copper pour for thermal dissipation. Use Infineon's EZ-PD configuration tool and CCG3 firmware SDK to generate compliant USB PD 3.0 firmware. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found on the manufacturer product page, providing an engineering-ready reference for USB-PD port design.
CYPD3135-40LQXIT - EZ-PD CCG3 USB-C/PD Controller, ARM M0 | Infineon
The Infineon CYPD3135-40LQXIT is an EZ-PD CCG3 USB Type-C port controller with USB Power Delivery (PD) support, integrating 128 kB of flash and an ARM Cortex-M0 core in a 40-pin UFQFN (6x6 mm) package. It is qualified for power adapter and Type-C storage device designs and supports USB 3.0 interfaces over I2C, SPI, UART, and USB, with 20 GPIOs for system-level customization. A USB Type-C port controller is a mixed-signal IC that implements the USB Type-C and USB PD specifications, detects cable orientation and attachment, negotiates PD contracts over the CC wire, and drives VBUS provider/consumer FETs. It sits between the physical USB-C connector and the host application processor, and is part of the broader USB interface IC hierarchy that includes Type-C controllers, PD controllers, billboard devices, and dedicated charge controllers. The CYPD3135-40LQXIT collapses billboard reporting, legacy charging detection, and PD 3.0 negotiation into one part. Key features include USB PD 3.0 compliance, a billboard controller function, 2.7-21.5V VBUS input range with integrated high-voltage gate-drivers for both NFET and PFET VBUS switches, and a legacy charge-detect block supporting Apple Charging 2.4A, QC 4.0, and Samsung AFC. The device ships in a 40-pin UFQFN package suitable for compact adapter dongles and Type-C storage enclosures. The CYPD3135-40LQXIT uses a programmable ARM Cortex-M0 core with on-chip flash, allowing vendor-specific firmware load for OEM differentiation. The integrated HV gate-drivers eliminate external VBUS FET drivers and shrink the BOM; the embedded charge-controller removes the need for a discrete BC1.2 chip. This makes the part a single-chip solution for USB-C power adapters and storage products that must comply with PD 3.0 and legacy charging protocols. Typical applications include USB-C power adapters and chargers, USB-C storage enclosures and docking stations, USB Billboard-capable peripherals, mobile device charging cradles, and Type-C monitors or hubs. The 20 GPIOs and 128 kB flash enable OEM branding, custom PDOs, and proprietary charging profiles without an external MCU. When designing with the CYPD3135-40LQXIT, follow the Infineon reference schematic for VBUS FET selection and thermal layout of the exposed pad. Validate against the USB-IF-CT3 USB PD 3.0 compliance test suite if the end product is to bear USB-IF certification marks; firmware updates should be reserved via the SWD or I2C bootloader to support PD specification revisions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single source to evaluate the CYPD3135-40LQXIT for adapter, dock, and Type-C storage designs.
CYPD3135-40LQXQ - EZ-PD CCG3 USB Type-C PD Controller | Infineon
The Infineon CYPD3135-40LQXQ is a USB Type-C port controller with USB Power Delivery (USB PD 3.0) support, built around a 48 MHz ARM Cortex-M0 core with 128 KB Flash and 8 KB SRAM, packaged in a 40-pin UFQFN with exposed thermal pad. The device is qualified to six 802.3 USB Type-C standards and supports USB PD 3.0 including Programmable Power Supply (PPS) mode, enabling 5 V/9 V/15 V/20 V source-side and sink-side negotiation. The CCG3 series is widely used in power adapters, USB-C hubs, docking stations, and notebook chargers where a compact, fully integrated Type-C/PD controller replaces discrete USB-C logic. Background - What is a USB Type-C Port Controller? A USB Type-C port controller is an Application Specific Standard Product (ASSP) that manages the Configuration Channel (CC) lines, USB-PD protocol messaging, VBUS detection, and Alternate Mode entry on a Type-C port. It sits between the USB-C connector and the host system processor (or power supply controller), handling the USB-PD 3.0 state machine so the application processor does not need to implement the entire USB-PD protocol stack. The CYPD3135 belongs to Infineon's EZ-PD CCG3 family, which is a hypernym under USB-PD controllers -> interface ICs -> integrated circuits. Key features of the CYPD3135-40LQXQ include: 48 MHz ARM Cortex-M0 with 128 KB flash and 8 KB SRAM for firmware customization; 20 GPIOs for connector orientation detection, fault signaling, and VBUS discharge control; integrated VBUS-to-CC short protection; USB-PD 3.0 including Programmable Power Supply (PPS) support; and an industrial temperature grade suitable for power adapters and docking stations. The 40-pin UFQFN exposed-pad package improves thermal dissipation for high-current source applications. Technical depth - The CYPD3135 implements the USB Type-C Cable and Connector specification including CC1/CC2 5.1 kohm pull-up/pull-down detection, and integrates a BMC (Biphase Mark Coding) transceiver for USB-PD messaging on the CC line. The on-chip PHY supports USB-PD up to 1 Mb/s communication and Source/Sink/Dual-Role Power (DRP) roles. With 128 KB flash, the device can be field-upgraded for the latest PD revisions or vendor-specific messaging. Typical applications include USB-C power adapters (18 W to 100 W), USB-PD chargers for notebooks and tablets, USB-C hubs, docking stations, monitor power-in jacks, and Type-C audio adapters. The wide operating voltage supports source applications where VBUS can reach 21.5 V during high-power contract. Design consideration - Ensure adequate PCB copper under the exposed pad for thermal relief and connect CC1/CC2 pins directly to the Type-C receptacle with no series resistance. Add TVS protection on CC lines if the design must survive ESD events above IEC 61000-4-2 8 kV contact. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.
CYPD3135-40LQXQT - EZ-PD CCG3 USB-C PD Controller, 40-QFN | Infineon
The Infineon (formerly Cypress Semiconductor) CYPD3135-40LQXQT is an EZ-PD CCG3 USB Type-C port controller with USB Power Delivery 3.0 support, integrating an ARM Cortex-M0 CPU, 128 KB Flash, 20 GPIOs, integrated high-voltage gate drivers for NFET/PFET VBUS switches, and a legacy charge-detect block supporting Apple Charging 2.4A, Qualcomm Quick Charge 4.0, and Samsung AFC. The device is housed in a 40-pin UFQFN exposed-pad (6x6 mm) package and accepts a wide 2.7 V to 21.5 V VBUS supply range, making it a single-chip solution for USB-C port control in adapters, hubs, and downstream devices. Background — What is a USB Type-C Port Controller? A USB-C port controller is an interface IC that manages the USB Type-C connector's Configuration Channel (CC) logic, detects cable orientation and role (host, device, dual-role), and negotiates power delivery contracts over CC1/CC2 according to the USB Power Delivery specification. Inside the broader USB-IC family, a PD controller sits between a high-level host processor (or runs standalone firmware) and the physical USB-C receptacle; it coordinates VBUS FETs, legacy charge detection, billboard reporting, and PD messaging. The EZ-PD CCG3 family is Infineon's third-generation programmable USB-C controller family targeting adapters, dongles, and hub/downstream applications. Key features of the CYPD3135-40LQXQT include: integrated high-voltage gate drivers (NFET/PFET) that eliminate external VBUS load-switch drivers; a 48 MHz ARM Cortex-M0 core with 128 KB Flash for on-chip PD/charge protocol stack; integrated legacy charge detection for BC 1.2, Apple 2.4A, QC 4.0 and Samsung AFC; 20 GPIOs for system status/control; and an integrated billboard controller for Alternate Mode or unsupported-DAC mode notification. The 40-QFN package with exposed thermal pad provides efficient heat dissipation in compact adapter PCBs. Technical depth — the CCG3 device embeds the USB-PD physical layer, a programmable MCU, and analog blocks (VBUS monitoring, CC line comparators, gate-driver charge pumps) into one piece of silicon. The 2.7-21.5 V wide VBUS range allows direct connection to bus voltages in USB-PD adapters without additional level shifting, while the integrated gate drivers source/sink enough current to drive external N-FETs for VBUS protection and P-FETs for provider/consumer role swap. Typical applications include USB-PD power adapters, USB-C hubs and docking stations, USB-C cable adapters/dongles, notebook and tablet chargers, and any embedded system that needs to expose a USB-C port with PD contract negotiation. The compact 40-QFN (6x6 mm) footprint fits tight adapter housings. Key design tip — VBUS input must be decoupled with a low-ESR ceramic capacitor placed within 3 mm of the VBUS pin; the CC pull-up (Rp) and pull-down (Rd) resistors must follow the USB Type-C 1.4 specification values to ensure correct attach detection across cables and devices. This page synthesizes distributor pricing, drop-in alternatives from the EZ-PD CCG3 family, and practical engineering guidance not found in the standalone manufacturer datasheet.
CYUSB3302-68LTXIT - HX3 USB 3.0 Hub Controller | Infineon
The Infineon CYUSB3302-68LTXIT is a USB 3.0 SuperSpeed hub controller from the HX3 family, integrating an ARM Cortex-M0 microcontroller core with 32 kB of ROM in a 68-pin VFQFN Exposed Pad package. It supports four downstream ports operating at Low-Speed, Full-Speed, Hi-Speed, and SuperSpeed (5 Gbps) and is designed for both embedded and standalone USB hub applications including battery-charging downstream ports. The 'T' suffix denotes tape-and-reel packaging for high-volume assembly, while the 'I' suffix indicates the industrial temperature grade. A USB 3.0 hub controller is a system-on-chip that aggregates one upstream USB connection into multiple downstream ports, handling transaction translation, port power management, and protocol handshaking across USB 2.0 and USB 3.0 link layers. Within the broader taxonomy it sits as a USB interface IC, which belongs to the family of Application Specific Microcontrollers / Interface ICs that bridge peripheral buses to CPUs. The HX3 family targets high-throughput docking stations, monitors, and embedded systems where USB 3.0 bandwidth is required without external PHY complexity. Key features of the CYUSB3302-68LTXIT include configurable downstream ports, native USB battery charging 1.2 support, integrated 5 Gbps PHY, low-power states per USB 3.0 specification revision 1.0, and ARM Cortex-M0 firmware that the OEM can optionally customize. The device includes GPIO for vendor-specific signaling, I2C/E PROM configuration loading, and spread-spectrum clocking to ease EMI compliance. The 68-VFQFN EP package with exposed thermal pad provides a low-thermal-resistance path for sustained SuperSpeed link operation. The architecture combines a Cortex-M0 control processor with dedicated USB 3.0 and USB 2.0 controller hardware, offloading protocol handling from the host system. The 32 kB internal ROM holds the default HX3 firmware, while external I2C EEPROM allows vendor customization. USB 3.0 specification revision 1.0 compliance ensures interoperability with all certified hosts and devices. Typical applications include USB 3.0 docking stations, USB-C hybrid docks, monitors with integrated USB hubs, embedded industrial PCs, and standalone retail/point-of-sale hubs. Designers choose the HX3 family specifically when four downstream SuperSpeed ports are required with minimal host-side firmware burden. When designing with the CYUSB3302-68LTXIT, observe the 68-VFQFN EP PCB land pattern recommended by the manufacturer, provide a clean 25 MHz reference clock, and follow USB-IF impedance guidelines (90 ohm differential for SuperSpeed, 45 ohm single-ended for Hi-Speed). Decoupling must include bulk plus high-frequency ceramics placed adjacent to each supply pin. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving procurement and design engineers a single reference for the CYUSB3302-68LTXIT.