بەرهەمەکان (5,100+)

CYUSB3328-88LTXC - HX3 USB 5 Gbps Hub Controller | Infineon
CYUSB3328-88LTXC

CYUSB3328-88LTXC - HX3 USB 5 Gbps Hub Controller | Infineon

The Infineon CYUSB3328-88LTXC is an EZ-USB HX3 USB 3.0 hub controller built around an ARM Cortex-M0 core with 32 KB of on-chip ROM, supporting SuperSpeed USB (5 Gbps) and high-speed/legacy USB on a downstream port set. Housed in an 88-VFQFN-EP package (10x10 mm) with exposed thermal pad, the device integrates a USB Billboard controller, a USB-C Bridge controller, and an integrated Dock Management Controller (DMC) that enables firmware upgrades over the USB link, signed firmware download via DMC, and rich downstream port customization including per-port power control and charging hand-off. A USB 3.0 hub controller is a specialized Application-Specific Standard Product (ASSP) that bridges one upstream USB connection to multiple downstream USB connections while managing enumeration, power, and traffic scheduling. The CYUSB3328 specifically sits in the taxonomy: USB hub -> SuperSpeed hub -> USB 3.0 hub controller -> mixed-signal ASSP -> semiconductor. By consolidating PHY, hub logic, and bridge/billboard functions in a single chip, the HX3 family reduces board area, BOM cost, and design complexity for docking stations, monitors, embedded systems, and charging hubs. The 5 Gbps SuperSpeed datapath is critical because USB 3.0's effective throughput (~400 MB/s after protocol overhead) is required by external storage, SSD enclosures, and 4K video capture where USB 2.0 would bottleneck. Key features include 5 Gbps SuperSpeed USB 3.0 with backward-compatible USB 2.0/1.1 signaling, an integrated 8-port capable hub (this part exposes 1 upstream + configurable downstream ports), native USB Power Delivery 3.0, Battery Charging v1.2 (BC v1.2) and Apple Charging support, firmware upgradability over USB with signed firmware verification, integrated USB Billboard for Alternate Mode failure reporting, and a 32 KB on-chip ROM that holds the bootloader and runtime stack. The part operates from a single 3.3 V supply and provides GPIO for port indicators and VBUS control. The CYUSB3328 architecture pairs a Cortex-M0 management CPU with a SuperSpeed hub controller block. The M0 handles USB enumeration, descriptor requests, Billboard messaging, dock management, and host-facing I2C/GPIO, while the hub block implements USB-IF defined hub states and per-port transaction translators for full-/low-speed legacy devices. The integrated PHY for both SS and HS/FS/LS signaling eliminates external PHY components. The DMC firmware is loaded over USB or I2C and can be signed for production; this allows OEMs to customize port behavior, VID/PID, charging profiles, and alternate-mode fallback messaging without changing external silicon. Typical applications include USB Type-C docking stations, USB 3.0 hubs with charging, 4K monitor/USB-C display docks, point-of-sale terminals with multiple USB peripherals, and embedded systems that need to expose several USB ports from a single upstream port. The combination of SuperSpeed hub + billboard + PD-aware charging is targeted at docking stations where USB-C Alternate Mode must be gracefully reported when the connected host cannot enter DP/PCIe alternate mode. Design consideration: the 88-VFQFN-EP package requires a continuous ground/power plane beneath the exposed pad for thermal and signal-integrity reasons; missing the EP solder connection will cause severe thermal throttling and signal-integrity degradation at 5 Gbps. Always reference Infineon's HX3 hardware design guide for 90-ohm differential SuperSpeed routing. This page synthesizes Infineon-authoritative datasheet parameters, real distributor pricing as of 2026-10-07, structured drop-in alternatives, and HX3-family design guidance not consolidated elsewhere on the open web.

RFQ پەیوەندی
CYUSB3328-88LTXI - HX3 USB 3.0 8-Port Hub Controller | Infineon
CYUSB3328-88LTXI

CYUSB3328-88LTXI - HX3 USB 3.0 8-Port Hub Controller | Infineon

The Infineon CYUSB3328-88LTXI is a USB 3.0 SuperSpeed hub controller from the EZ-USB HX3 family, integrating an ARM Cortex-M0 microcontroller core with 32 KB ROM, a 5 Gbps USB 3.0 PHY, and an 88-pin VFQFN exposed-pad package. The device delivers four downstream USB 3.0 ports plus a USB 3.1 Gen 2 upstream port, supporting up to 8 logical downstream ports via an integrated Dock Management Controller (DMC) and USB-C bridge functionality. Native battery-charging support includes USB Power Delivery 3.0, Battery Charging v1.2, and Apple Charging signatures. What is a USB hub controller? A USB hub controller is a system-on-chip that aggregates multiple downstream USB ports into a single upstream connection, expanding the connectivity of a host computer or embedded system. Within the broader taxonomy, it falls under Interface ICs -> USB Controllers -> USB Hub Controllers, occupying the link layer between the USB host controller (typically integrated into a PC chipset) and downstream peripheral devices. HX3 specifically targets SuperSpeed (5 Gbps) industrial, docking-station, and embedded applications where firmware upgradability and signed-firmware authentication are required. Key features of the CYUSB3328-88LTXI include: 5 Gbps USB 3.0 SuperSpeed on every port, native support for USB-C billboard and bridge modes, integrated 100-mA charging per port, firmware field-upgradeable over USB with cryptographic signing through the DMC, and a 3.0V to 3.6V single-supply operation. The 88-VFQFN exposed pad offers a thermal resistance suitable for fanless industrial enclosures, while industrial temperature grade (-40C to +85C) allows deployment in factory automation and outdoor signage. Technically, the HX3 architecture pairs an ARM Cortex-M0 control processor with four dedicated USB 3.0 physical layers and a shared USB 2.0 high-speed hub block. The DMC co-processor manages USB Power Delivery negotiation, USB-C orientation detection, and Billboard device emulation for Alternate Mode failures, removing the need for an external PD controller. Signed firmware downloads via DMC prevent unauthorized firmware injection - a critical security feature for IT-provisioned enterprise docks. Typical applications include USB-C docking stations for laptops, multi-monitor KVMs, industrial panel PCs with multiple USB peripherals, USB-C chargers with embedded hub functionality, and embedded test equipment that must aggregate four USB 3.0 cameras or storage devices. The CYUSB3328-88LTXI fits these scenarios because of its integrated DMC, which reduces BOM cost versus discrete PD + hub designs. Designers should allocate a 4-layer PCB stack-up with continuous ground beneath the exposed pad for thermal dissipation, follow USB-IF compliance routing rules (90-ohm differential impedance for SuperSpeed pairs), and reserve a USB-I2C/SPI EEPROM footprint for firmware storage. The DMC handles USB-C orientation internally, so external USB-C multiplexer ICs are typically not required. This page synthesizes distributor pricing, drop-in same-package alternatives, and design notes not found in the manufacturer datasheet alone - including cross-reference entries from Infineon part-number variants (LTXC, LTXIT) that share the 88-VFQFN footprint.

RFQ پەیوەندی
DAC8740HRGER - Low-Power Fieldbus Modem | Texas Instruments
DAC8740HRGER

DAC8740HRGER - Low-Power Fieldbus Modem | Texas Instruments

The Texas Instruments DAC8740HRGER is a low-power HART, FOUNDATION Fieldbus, and PROFIBUS PA-compatible modem with a UART interface, offered in a 24-VQFN 4 x 4 mm package. The verified distributor listing identifies the interface and package, while the manufacturer describes the DAC874xH family as a half-duplex physical-layer modem for industrial process-control and automation systems. Its supported industrial protocols make it suitable for connecting sensors, actuators, transmitters, controllers, and field equipment. A fieldbus modem is an interface IC that converts digital UART information into the physical signaling required by an industrial fieldbus, and it can also receive and decode the corresponding bus waveform. In the HART mode described by Texas Instruments, the DAC8740H integrates the circuitry required for half-duplex HART physical-layer operation in slave or master configurations, reducing the amount of external circuitry needed by the transmitter. FOUNDATION Fieldbus and PROFIBUS PA compatibility broadens its relevance in process plants and industrial automation networks. The verified product data establishes the 24-VQFN 4 x 4 mm package and the UART-based architecture, but it does not provide a complete electrical parameter table in the supplied excerpts. Consequently, operating voltage, current consumption, baud rate, analog performance, temperature range, and protection limits are retained as datasheet-needed fields rather than inferred from the product family name. This conservative approach prevents protocol, supply, and signal-integrity assumptions from entering a design prematurely. The DAC8740HRGER is positioned for industrial measurement and control rather than ordinary consumer UART links. Its fieldbus compatibility is relevant when a controller must communicate with a 2-wire industrial process network through a defined physical layer. The UART interface gives the host processor a familiar digital connection, while the integrated modem circuitry reduces the design burden associated with waveform generation, reception, filtering, and bus coupling. Exact baud-rate and loading requirements should be checked against the complete manufacturer documentation before schematic release. Typical application areas include HART-connected pressure and temperature transmitters, FOUNDATION Fieldbus process instruments, PROFIBUS PA field devices, industrial controllers, sensor gateways, actuator interfaces, and factory automation equipment. The compact VQFN package helps reduce board area compared with larger leaded implementations, although exposed-pad layout, thermal performance, grounding, and high-speed signal routing must be handled according to the manufacturer's land pattern and layout guidance. The most important design step is to select the external network components and protection scheme around the exact bus topology, cable length, and operating mode. Fieldbus transceivers are exposed to industrial transients and long cables, so power-supply filtering, surge protection, grounding, connector design, and separation from noisy switching nodes deserve careful review. Verify pin-level multiplexing, supply sequencing, decoupling, and exposed-pad connections against the complete datasheet before layout sign-off. This page combines the verified manufacturer identity, protocol positioning, package information, distributor references, and engineering cautions. It is intended to help engineers locate the correct device, understand its industrial interface role, and identify which datasheet parameters still require confirmation before a production design is released.

RFQ پەیوەندی
DAC8740HRGET - 2.7V-5.5V HART/Fieldbus Modem | TI
DAC8740HRGET

DAC8740HRGET - 2.7V-5.5V HART/Fieldbus Modem | TI

The Texas Instruments DAC8740HRGET is a low-power HART and FOUNDATION Fieldbus modem integrated circuit with a 2.7 V to 5.5 V supply range, housed in a 24-pin VQFN 4 mm × 4 mm package. It belongs to the DAC874xH family, which supports HART, FOUNDATION Fieldbus, and PROFIBUS PA communications for industrial process-control and factory-automation equipment. The device can operate as either a half-duplex HART master or slave and is designed to minimize the number of external components required by a fieldbus physical layer. A HART modem is the physical-layer interface used to superimpose digital communication signals on 4–20 mA analog instrumentation circuits. A FOUNDATION Fieldbus or PROFIBUS PA interface similarly combines process communication with power delivery over an industrial fieldbus. These interfaces allow sensors, transmitters, controllers, and other field devices to exchange data over the same wiring infrastructure used for measurement and actuation. The DAC8740HRGET provides a compact 2.7 V to 5.5 V operating supply range for integration into modern industrial electronics. Its half-duplex operating arrangement supports both master and slave configurations, while its integrated modem functionality is intended to reduce board area and external circuitry. The VQFN-24 4 mm × 4 mm package also supports compact transmitter and receiver designs where PCB space is constrained. The DAC8740H family was created for industrial process-control and industrial-automation applications requiring interoperable fieldbus connectivity. In HART mode, the integrated circuitry is intended to perform the required half-duplex physical-layer functions with minimal external components. This makes the device applicable to transmitter boards, sensor interfaces, communication controllers, data-acquisition equipment, and connected process-control modules. Typical uses include 4–20 mA HART transmitters, FOUNDATION Fieldbus host and field equipment, PROFIBUS PA measurement devices, industrial sensor gateways, process-monitoring instruments, and factory automation controllers. Designers should verify the exact electrical limits, communication timing, external component requirements, and thermal limits against the manufacturer datasheet before finalizing a production design. A critical design consideration is selecting the correct fieldbus termination, coupling, protection, and decoupling network. The 2.7 V to 5.5 V supply range must remain valid under transient conditions, and exposed industrial connections may require surge and ESD protection beyond the modem's core communications function. Layout should keep sensitive analog and modem nodes away from high-current switching paths. This product page combines verified distributor pricing, package information, family capabilities, source links, and drop-in replacement analysis with practical industrial-interface design guidance. It distinguishes verified alternatives from broader functional equivalents so engineers can assess PCB replacement risk before committing to a redesign.

RFQ پەیوەندی
DAC8741HRGET - HART Modem with SPI | Texas Instruments
DAC8741HRGET

DAC8741HRGET - HART Modem with SPI | Texas Instruments

The Texas Instruments DAC8741HRGET is a low-power HART, FOUNDATION Fieldbus, and PROFIBUS PA-compatible modem with an SPI interface, 24-pin VQFN (RGE) package, and a specified temperature range of -55°C to +125°C. It is designed for industrial process-control and industrial-automation equipment requiring a dedicated digital communication interface for fieldbus networks. A HART modem is a physical-layer interface that adds digital communication over an analog instrumentation signal path. As a modem IC, the DAC8741H belongs to the interface-IC hierarchy, connecting embedded controllers with HART-compatible transmitters, sensors, actuators, and fieldbus equipment. The TI product page describes the device as a HART, FOUNDATION Fieldbus, and PROFIBUS PA-compliant modem suitable for both slave and master configurations in HART mode. The principal feature of the DAC8741HRGET is its SPI host interface. The verified product information states that the interface includes a DO pin for daisy-chain support, together with interrupts and other control features. This allows a host microcontroller or processor to configure the modem and exchange status and command information through a serial interface while the integrated physical-layer circuitry handles the fieldbus signal. The device is offered in a compact 24-VQFN package measuring 4 mm by 4 mm. Its industrial operating-temperature designation covers -55°C to +125°C, making the qualified ordering variant suitable for harsh industrial environments when the complete system requirements, qualification records, and application conditions are independently reviewed. The ordering suffix identifies the RGE package, and HRGET is supplied in tape-and-reel form. Typical uses include process transmitters, fieldbus sensor transmitters, industrial controllers, data acquisition equipment, remote I/O systems, and PROFIBUS PA-compatible field devices. In these systems, the DAC8741HRGET can reduce the need for discrete modem circuitry while providing a standardized host-side connection through SPI. Designers should confirm the exact receiver and transmitter implementation, timing limits, electrical levels, and external-component requirements against the manufacturer datasheet before release. The SPI signals, analog fieldbus connection, supply rails, grounding, and exposed-pad layout must be routed according to the recommended application circuit. Component availability and lifecycle commitments should also be checked for the intended production program. This page consolidates verified manufacturer and distributor information with transparent data-gap markers, package guidance, comparison rows, and application-focused engineering context. It also distinguishes verified facts from specifications that require confirmation in the latest Texas Instruments datasheet.

RFQ پەیوەندی
DAC8742HPBS - HART Modem Interface | Texas Instruments
DAC8742HPBS

DAC8742HPBS - HART Modem Interface | Texas Instruments

The Texas Instruments DAC8742HPBS is a HART modem interface integrated circuit with UART and SPI support, designed for HART, FOUNDATION Fieldbus, and PROFIBUS PA industrial communication systems. It is packaged in a 32-TQFP (5x5) package and serves as the signal-conditioning interface between a host controller and fieldbus wiring. The verified source data identifies the device specifically as a HART modem interface, while detailed electrical limits, temperature ratings, and internal interface timing remain unavailable in the supplied records. A HART modem interface is a signal-conditioning IC within the broader industrial communication and data-conversion hierarchy. It encodes and decodes Frequency Shift Keying signals used by HART-compatible fieldbus equipment. This allows an embedded controller to communicate over legacy 4-20 mA instrumentation loops without implementing the analog modulation and filtering as discrete circuitry. In a FOUNDATION Fieldbus or PROFIBUS PA installation, the modem interface supports the physical signaling layer while higher-level protocols and safety mechanisms remain the responsibility of the host system. The DAC8742HPBS is valued for integrating dedicated modem functionality into a compact 32-TQFP device. Its UART and SPI host interfaces provide selectable connectivity to embedded processors, allowing command and data transfer between the modem and application firmware. The 5x5 mm package also supports space-constrained industrial instrumentation, although exposed-pad layout and thermal verification must follow the manufacturer package drawing. Because the supplied data does not expose individual pin assignments, supply limits, isolation ratings, or accuracy figures, those details must be checked in the official DAC8742H documentation before schematic approval. Typical uses include HART-compatible sensor transmitters, pressure and flow instrument interfaces, industrial process-control modules, and FOUNDATION Fieldbus or PROFIBUS PA equipment. In these systems, the DAC8742HPBS reduces the discrete component count associated with analog modem circuitry and gives the host MCU a structured digital control path. The principal engineering trade-off is that the modem interface is only one part of the communication chain: the transmitter still requires suitable loop power, filtering, surge protection, grounding, and validated fieldbus wiring. For new designs, verify the exact device variant, supply rails, UART and SPI logic levels, receive bandwidth, transmit modulation limits, loop-current interface, and exposed-pad requirements in the official Texas Instruments datasheet. Do not derive those values from the distributor snippets. The manufacturer product page describes the DAC8742H as HART, FOUNDATION Fieldbus, and PROFIBUS PA compliant with UART/SPI support, making it the authoritative starting point for design review. This page combines verified distributor availability, manufacturer positioning, package information, replacement analysis, and practical integration guidance. It also separates confirmed facts from parameters that require datasheet verification, helping engineers avoid treating incomplete distributor metadata as a complete electrical specification.

RFQ پەیوەندی
DG187AA - SPST Analog Switch, JFET, TO-100-10 | Vishay
DG187AA

DG187AA - SPST Analog Switch, JFET, TO-100-10 | Vishay

The Vishay Siliconix DG187AA is a single-channel SPST (single-pole single-throw) analog switch built around an N-channel JFET switching element with an integrated level-shifting driver. Housed in a 10-pin TO-100 metal can package (round, through-hole, 10 leads), it provides approximately 30 Ohm on-resistance and is part of the DG181 through DG191 analog-gate family originally introduced by Intersil and now manufactured by Vishay Siliconix. According to the verified distributor listings, it is categorized as an SPST analog switch IC. An analog switch (also called a JFET analog gate or solid-state analog switch) is an electronic component that uses a semiconductor device (typically a JFET or MOSFET) to connect or disconnect an analog signal path under the control of a digital logic input. Analog switches sit within the broader taxonomy of signal switches -> multiplexers/switches -> interface ICs -> integrated circuits, and they are essential whenever an analog signal must be routed without injecting distortion, charge injection, or significant series resistance. The DG187AA's JFET architecture keeps the on-resistance relatively constant over a wide analog signal range, which is a key advantage over simple MOSFET-only designs in precision instrumentation. Key differentiating features of the DG187AA include: (1) a high-speed level-shifting driver that accepts low-level CMOS/TTL-compatible inputs (down to approximately 0.8V to 2V) and uses them to control the JFET switch state, (2) analog signal range operation that suits both unipolar and bipolar audio/precision signals, (3) low charge injection thanks to the JFET topology, and (4) a hermetic TO-100 metal can that supports military temperature grades (-55C to +125C). The metal-can packaging also provides excellent EMI shielding for sensitive analog signal routing in instrumentation front-ends. In terms of electrical architecture, the DG187AA integrates the JFET switch die and the level-shifting driver die within a single TO-100 can, allowing the part to be driven directly from logic-level inputs without external pull-ups or level translators. This single-package integration reduces board area and simplifies PCB layout compared with discrete JFET-plus-driver implementations. The switching speed, while not as fast as modern CMOS analog switches, is sufficient for audio, instrumentation multiplexing, sample-and-hold front-ends, and legacy industrial signal routing. Typical applications for the DG187AA include: (1) precision instrumentation multiplexers, (2) audio signal routing in professional and broadcast equipment, (3) sample-and-hold amplifier front-ends, (4) data-acquisition system signal gating, (5) legacy industrial process-control signal switching, and (6) military and aerospace signal routing where the TO-100 hermetic can is required. The MIL-spec /883 variant (DG187AA/883) confirms the part's qualification for harsh-environment designs. When designing with the DG187AA, note that the TO-100 package has 10 leads arranged in a circular metal can, with pin 1 typically marked by a tab or dot near the package base. Because the package is a through-hole metal can (not surface-mount), PCB layout requires plated through-holes on a 0.230 inch lead circle typical of TO-100 cans. Always consult the manufacturer datasheet for the exact pinout, especially when migrating from the /883 to the commercial-temperature variant. This page synthesizes distributor pricing, hermetic package availability, MIL-spec drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
DG202DY+ - 4-Channel SPST CMOS Switch | Analog Devices
DG202DY+

DG202DY+ - 4-Channel SPST CMOS Switch | Analog Devices

The Analog Devices DG202DY+ is a four-channel, normally open SPST CMOS analog switch with a maximum on-resistance of 200 ohms, an on-time of 600 ns, and operation from ±4.5 V to ±18 V. It is packaged in a 16-pin SOIC for surface-mount systems requiring independent analog signal routing. The four isolated switches support bidirectional signal paths while normally presenting a high-impedance state when a channel is off. An analog switch is an integrated semiconductor device that connects or isolates nodes under digital control. The DG202 belongs to the CMOS analog-switch hierarchy, which sits within interface ICs and broader signal-management systems. Unlike a mechanical relay, it changes state rapidly without moving mechanical contacts. This makes it suitable for precision test equipment, signal routing, instrumentation, and industrial control systems where repeatable switching and compact implementation matter. The DG202 provides four independent single-pole, single-throw channels, 200-ohm maximum on-resistance, and 600-ns maximum on-time. Its normally open configuration means that each switched terminal remains disconnected until the corresponding control input is asserted. The manufacturer specifies continuous operation with dual supplies from -18 V to +18 V, including operation near ±4.5 V. These characteristics make the device suitable for routing bipolar or unipolar signals when the system requires a compact four-channel solution. The DG202 is functionally distinguished from the DG201 by inverted control polarity, while the DG212 provides the complementary functional behavior within the related family. According to the Analog Devices product page, the switches are designed to avoid latch-up when power is disconnected while input signals remain connected. That behavior supports more dependable system power sequencing, although correct supply sequencing and input-voltage limits must still be observed in the final circuit. Typical applications include automated test systems, data-acquisition front ends, analog signal multiplexing, industrial process monitoring, laboratory instrumentation, and control systems. The device can route sensors, conditioned analog outputs, reference signals, or feedback paths under microcontroller control. Four channels in one package reduce component count and make it especially useful where several independent analog signals must be selected or disconnected. Layout should keep switch traces short and provide a solid ground reference because high on-resistance makes the switch sensitive to leakage, contamination, and PCB contamination-related leakage. Avoid routing inputs beyond the permitted signal range, account for off-state leakage when designing high-impedance networks, and use the control-input timing and power-sequencing guidance in the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins with a short return path. This page combines the DG202DY+ technical specifications, lifecycle information, application guidance, and verified sourcing references. It also distinguishes true same-footprint drop-in options from related DG201, DG202, and DG212 devices whose control polarity or package prevents unqualified substitution.

RFQ پەیوەندی
DG211CJ+ - 4-Channel SPST Analog Switch | Maxim Integrated
DG211CJ+

DG211CJ+ - 4-Channel SPST Analog Switch | Maxim Integrated

The Maxim Integrated DG211CJ+ is a quad SPST CMOS analog switch with four independently controlled channels, 175 ohm maximum on-resistance, and a 16-pin PDIP package. It supports dual-supply operation from ±4.5 V to ±18 V and is designed for general-purpose routing of analog signals in communications, instrumentation, process-control, and computer-peripheral equipment. An analog switch is a semiconductor device that routes signals between circuit nodes under digital control. The DG211CJ+ belongs to the hierarchy of analog switches, multiplexers, interface ICs, and semiconductor components. Its four single-pole single-throw channels provide normally closed paths, making it useful when a system must maintain a connection until an active control signal changes the selected route. The device provides a maximum on-resistance of 175 ohm and a 1:1 signal configuration across four circuits. The manufacturer identifies the DG211 family as CMOS analog switches with low cost and general-purpose switching functions. Operation across positive and negative supplies supports bipolar analog signals in instrumentation and signal-routing systems, while the individual digital controls allow each channel to be operated independently. The DG211 and DG212 devices are described by the manufacturer as normally closed, quad SPST CMOS analog switches that can operate with supplies from ±4.5 V to ±18 V. Maxim also states that the DG211 family will not latch up if the power supplies are disconnected while input signals remain connected, and the devices feature guaranteed break-before-make switching. These characteristics help control transient current and undefined states during control transitions. Typical uses include analog measurement front ends, process-control interfaces, communications equipment, test equipment, and peripheral signal routing. In a measurement system, separate DG211CJ+ channels can connect sensors or reference signals to a shared analog front end while keeping unused paths connected. The device can also support signal isolation and source selection when system behavior requires a default connection that remains active until commanded otherwise. When designing a circuit around the DG211CJ+, verify input and output signal amplitudes against the supply rails, observe the control-logic thresholds, and maintain the specified continuous and peak terminal currents. Decoupling capacitors should be placed close to the supply pins, and control traces should be kept away from sensitive analog routes. The PDIP package also requires adequate insertion clearance and appropriate socket or soldering practices during assembly. This product page combines the manufacturer family information, distributor listings, cross-reference findings, package details, and practical application guidance. It highlights verified distinctions among available DG211 ordering codes and focuses drop-in comparison on the same 16-pin PDIP footprint rather than presenting surface-mount or electrically different devices as direct replacements.

RFQ پەیوەندی
DG211CUE+ - 4-Channel 175Ω SPST Analog Switch | Analog
DG211CUE+

DG211CUE+ - 4-Channel 175Ω SPST Analog Switch | Analog

The Analog Devices DG211CUE+ is a quad SPST normally closed CMOS analog switch with 175 Ω maximum on-resistance, housed in a 16-pin TSSOP package. It supports dual supply operation from ±4.5 V to ±18 V and provides four independently controlled channels for routing bipolar or single-ended signals. The device is specified for commercial-temperature operation from 0 °C to +70 °C, with a maximum turn-off time of 500 ns and guaranteed break-before-make operation. An analog switch is a semiconductor device that connects or isolates circuit nodes under digital control while preserving the electrical characteristics of the passing signal. The DG211 belongs to the CMOS analog switch hierarchy, which also includes multiplexers, selectors, and routing switches. Its normally closed configuration keeps each selected signal path connected until the corresponding control input commands a break, making the DG211 useful in test systems, audio routing networks, measurement equipment, and configurable signal-conditioning circuits. Key characteristics include four independent SPST channels, 1:1 signal routing, a 175 Ω maximum on-resistance, and low 5 nA leakage. Break-before-make behavior prevents the momentary overlap of old and new paths that could produce an invalid signal during transition. The manufacturer also guarantees latch-up protection when the power supplies are disconnected while input signals remain connected, improving robustness in equipment where rails can collapse before signal sources. The DG211 uses CMOS construction to provide low off-leakage and low power consumption while operating across a wide voltage range. Its maximum switching interval is 1 μs, with a specified turn-off time no greater than 500 ns. Because on-resistance is 175 Ω at the maximum rating, the switch introduces insertion loss and contributes to noise when used in high-impedance precision paths. The device is therefore most appropriate for moderate-bandwidth routing rather than low-loss RF distribution. Typical uses include four-channel test and measurement systems, audio input and output routing, instrumentation signal selection, and industrial control interfaces. In each case, the control logic determines which normally closed path remains connected. The commercial DG211CUE+ is suited to room-temperature equipment, while extended-temperature or automotive requirements call for a qualified grade rather than this commercial-temperature variant. When laying out the board, route each switched signal away from digital control traces and provide a solid ground reference around the package. Keep power-supply decoupling close to the device and verify that every signal node remains within its absolute maximum rating, especially during power sequencing. This page combines device specifications, family-level alternatives, comparison data, and practical layout guidance for faster design review.

RFQ پەیوەندی
DG211CY+ - Quad SPST CMOS Analog Switch | Analog Devices
DG211CY+

DG211CY+ - Quad SPST CMOS Analog Switch | Analog Devices

The Analog Devices DG211CY+ is a monolithic quad SPST CMOS analog switch in a 16-pin SOIC package. It provides four independent single-pole single-throw channels with a maximum on-resistance of 175 ohm, operates from dual positive and negative supplies of ±4.5 V to ±18 V, and supports true bidirectional signal conduction in the ON state. A CMOS analog switch is an integrated semiconductor device that routes analog signals between circuit nodes under digital control. The DG211 family belongs to the analog-switch and multiplexer hierarchy, which supports general-purpose signal routing in communications, instrumentation, process control, and computer peripheral equipment. The DG211 switches are normally closed, so each channel connects its input to its output whenever its control input is inactive. Key features include four SPST channels, a 175 ohm maximum on-resistance, operation across ±4.5 V to ±18 V dual-supply ranges, and a 500 ns maximum off-time. According to the Analog Devices DG211 data sheet, the DG211 will not latch up when the power supplies are disconnected while input signals remain connected. Break-before-make operation is also guaranteed, which helps prevent two signal sources from being momentarily shorted together. The devices can block signals up to 30 V peak-to-peak in the OFF condition, making them useful for protecting downstream circuitry from higher-voltage external signals. True bidirectional ON-state behavior allows the same switch to route either signal direction, while the normally closed configuration provides a defined signal path during power-up and control-failure conditions. Typical applications include multimeter and test-equipment input selection, process-control signal routing, communications equipment, and peripheral interface boards. Designers should verify the control-logic thresholds, switching timing, leakage, charge injection, and absolute maximum ratings against their signal amplitude and impedance before applying the switch. This page consolidates verified manufacturer and distributor information, package and supply details, application guidance, and qualified drop-in information for DG211CY+ designs.

RFQ پەیوەندی
DG211DJ+ - Quad SPST CMOS Analog Switch | Analog Devices
DG211DJ+

DG211DJ+ - Quad SPST CMOS Analog Switch | Analog Devices

Analog Devices DG211DJ+ is a four-circuit, normally closed, single-pole single-throw CMOS analog switch with an on-resistance of 175 ohm in a 16-pin PDIP package. The manufacturer identifies the DG211 family as a production device and specifies operation from ±4.5 V to ±18 V supplies. Its four integrated switches provide break-before-make operation and are designed to avoid latch-up when supply rails are disconnected while signals remain connected. An analog switch is an electronically controlled semiconductor device that routes signals between circuit nodes without continuously conducting them. The DG211 belongs to the analog-switch and multiplexer hierarchy, where CMOS implementations combine low signal distortion with TTL-compatible control inputs. Each DG211 switch is normally closed, meaning its default connection remains active until the corresponding control input changes state. This behavior is useful for signal routing, test-point isolation, fallback paths, and analog measurement systems. The DG211’s four SPST channels provide independent control of four signal paths. Its 175-ohm on-resistance is the principal signal-path parameter identified for the device, while the ±4.5 V to ±18 V supply range allows operation with positive and negative analog rails. The manufacturer also specifies break-before-make behavior, helping prevent two switched paths from momentarily connecting together during control transitions. The DG211DJ+ ordering code places this quad switch in a 16-pin PDIP package. CMOS construction gives the DG211 low static power characteristics relative to many mechanical or bipolar relay alternatives. Because the device uses MOSFET-based switching elements, its on-state behavior changes with signal amplitude and supply configuration. Designers should therefore evaluate resistance, off leakage, charge injection, capacitance, and logic thresholds against the particular source and load impedance. The fast transition and low on-resistance make the device practical for precision test systems, data-acquisition front ends, instrumentation, and controlled analog paths. Typical uses include switching sensor outputs into measurement amplifiers, isolating channels in automated test equipment, selecting signal sources in laboratory instruments, and preserving analog connections during power-up or fault conditions. The normally closed topology is especially valuable when a default connection must remain intact if control logic is unpowered or temporarily unavailable. The 16-pin PDIP package is appropriate for through-hole assembly, prototypes, educational systems, and designs where a socketed DIP implementation simplifies maintenance. Designers should preserve the recommended supply and signal limits, place bypass capacitance close to the supply pins, and use pull resistors where control inputs may float during reset. The break-before-make and latch-up characteristics improve transition reliability, but external logic still must not exceed the input ratings. Because analog-switch performance depends on source impedance, load impedance, frequency, and supply voltage, prototype measurements should verify bandwidth and distortion before high-volume deployment. This product record combines the manufacturer’s production status, switch topology, resistance, supply range, package information, ordering data, and drop-in comparison guidance with practical PCB, signal-integrity, and selection considerations. It is intended to help engineers identify whether the DG211DJ+ matches the required electrical behavior, normally closed routing, through-hole footprint, and control architecture before placing the part into a production design.

RFQ پەیوەندی
DG211DY+T - Quad SPST CMOS Analog Switch | Analog Devices
DG211DY+T

DG211DY+T - Quad SPST CMOS Analog Switch | Analog Devices

The Analog Devices DG211DY+T is a quad single-pole single-throw CMOS analog switch with four normally closed channels, a 175 ohm on-resistance and a 16-SOIC package. The device supports dual supply operation from ±4.5 V to ±18 V, provides glitch-free switching, and is specified over a -40 °C to +85 °C temperature range. Its four-channel architecture allows one package to route four independent analog signals while maintaining a common ground and supply arrangement. An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The SPST designation means each of the four internal switches has one pole and one throw, while normally closed means each signal is connected to its throw terminal when the control input is inactive. The DG211 belongs to the broader analog-switch hierarchy, alongside multiplexers and demultiplexers, and provides a simple impedance-controlled routing function for test, measurement, and communication equipment. Key electrical characteristics include a maximum on-resistance of 175 ohm, a maximum turn-on time of 1000 ns, and a maximum turn-off time of 500 ns. Maxim guarantees break-before-make operation, reducing the interval during which old and new signal paths can overlap. The device is also guaranteed not to latch up when its power supplies are disconnected while input signals remain connected, an important robustness characteristic for externally biased analog nodes. The DG211 uses CMOS switch channels controlled by TTL-compatible control inputs. Its low-leakage design supports precision measurement systems where unintended charge transfer or off-state conduction can corrupt results. Operating from positive and negative rails allows direct connection to bipolar signals without translating every input through separate amplifiers, although common-mode voltage and supply limits must still be respected during layout and system design. Typical uses include automated test equipment, data-acquisition systems, instrumentation, communication routing, and analog signal multiplexing. A four-channel normally closed switch is particularly useful where a measurement path must remain connected during idle periods and disconnect only when the control logic selects another operating condition. PCB design should minimize capacitance on control and analog signal traces, keep routing short, and use a continuous ground reference beneath the device where practical. Because the switch is intended for analog signals rather than high-speed digital links, pay close attention to leakage, on-resistance, charge injection, and off-state isolation rather than digital edge-rate limits. This page consolidates manufacturer specifications, supply-chain observations, drop-in alternatives, and practical design guidance that engineers would otherwise have to assemble from separate datasheets and component listings.

RFQ پەیوەندی
DG212CJ+ - Quad SPST CMOS Analog Switch | Intersil
DG212CJ+

DG212CJ+ - Quad SPST CMOS Analog Switch | Intersil

The Intersil Corporation DG212CJ+ is a low-cost CMOS monolithic quad SPST analog switch with four normally open, 1:1 switching channels, 175 ohm on resistance, inverted control inputs, and a 16-pin PDIP package. According to the manufacturer datasheet, it supports dual supply operation from ±4.5 V to ±18 V and is designed for communications, instrumentation, process-control, sample-and-hold, disk-drive, test-equipment, and computer-peripheral applications. An analog switch is an integrated interface device that routes analog signals between external circuit nodes under digital control. The DG212CJ+ belongs to the CMOS analog-switch hierarchy, where each SPST channel provides one signal path with a normally open configuration. Its inverted control inputs allow the device to be selected by active-high or active-low system logic, while four independent switches can share common supply rails within one package. Key features include a 175 ohm maximum on resistance, a maximum turn-on time of 1000 ns, and a maximum turn-off time of 500 ns. The device is specified for a wide dual-supply range of ±4.5 V to ±18 V. According to the Analog Devices DG212 product page, the DG202 and DG212 family is guaranteed not to latch up when the power supplies are disconnected while input signals remain connected, improving recovery behavior in systems where rails can be removed before external circuitry. The DG212 family differs from the DG201 and DG211 families through its inverted control inputs. Within the DG202 family, the DG212 provides four normally open SPST channels, making it appropriate for signal isolation, test-point routing, programmable front ends, and general-purpose switching rather than fixed on-state multiplexing. Its CMOS implementation and simple logic interface suit compact analog and digital control systems where channel isolation and predictable switching timing are important. Typical uses include communication-system signal routing, process-control interfaces, disk-drive electronics, test equipment, sample-and-hold circuits, and computer peripherals. Engineers should pay attention to the inverted logic polarity and confirm that a low control level closes each normally open channel. Because this is a 16-pin PDIP device rather than a surface-mount package, it is most appropriate for through-hole legacy, industrial, instrument, and prototype designs where DIP availability is more valuable than compact placement. For reliable operation, use the pin-description table and recommended operating conditions in the manufacturer datasheet when assigning control and analog pins. Confirm signal levels against the applicable supply configuration and avoid exceeding ±18 V. This page combines manufacturer specifications, sourcing context, pin-usage guidance, and verified drop-in replacement information to support practical selection and board-level implementation.

RFQ پەیوەندی
DG212CY+ - Quad SPST 175Ω Analog Switch | Analog Devices
DG212CY+

DG212CY+ - Quad SPST 175Ω Analog Switch | Analog Devices

The Analog Devices DG212CY+ is a quad SPST CMOS analog switch with four normally open channels, a maximum on-resistance of 175 Ω, and a 16-lead SOIC package. It supports continuous operation from ±4.5 V to ±18 V. Each independent switch provides 1:1 signal routing for general-purpose analog and digital signal switching. An analog switch is an integrated semiconductor device that connects or disconnects signal paths under logic control. The DG212CY+ belongs to the analog switch hierarchy, where it complements multiplexers, demultiplexers, and matrix switchers. Its four SPST channels can isolate instrumentation inputs, route test signals, select external circuits, or provide break-before-make functions when driven by suitable control logic. The DG212 family uses low-cost monolithic CMOS circuitry and normally open contacts. Four independently controlled switches reduce external component count in systems requiring several signal connections. The maximum specified on-resistance is 175 Ω, making the device suitable for moderate-impedance signals rather than low-ohm precision measurement paths. Its 16-lead SOIC format supports conventional surface-mount assembly. The DG212CY+ can operate continuously with positive and negative supply rails from ±4.5 V to ±18 V. Analog Devices specifies latch-up-free behavior when the supply rails are disconnected while input signals remain connected. This feature helps avoid unintended current paths during power-down conditions. Control polarity distinguishes the DG212 from related DG211 devices, so control-logic compatibility must be checked before substitution. Typical uses include communications equipment, instrumentation, process-control systems, computer peripherals, automated test equipment, and signal-isolation circuits. The device is especially useful when multiple low-bandwidth or moderate-impedance paths must be selected independently. Its four channels can route sensor lines, select measurement sources, or disconnect external equipment from a shared bus. Layout should keep switched traces short and provide a low-impedance ground reference around the device. Input and output pins must remain within the absolute maximum ratings of the manufacturer datasheet, and unused control inputs should be driven to a defined logic state. Verify signal amplitude, supply polarity, control levels, and acceptable switching transients before finalizing the analog path. This product page combines the manufacturer’s switch description with practical substitution, comparison, and PCB-design guidance. It focuses on the electrical limits, control compatibility, package footprint, and application constraints that determine whether DG212CY+ is appropriate for a new design or an existing instrumentation and control board.

RFQ پەیوەندی
DG212DJ+ - Quad SPST CMOS Analog Switch | Analog Devices
DG212DJ+

DG212DJ+ - Quad SPST CMOS Analog Switch | Analog Devices

The Analog Devices DG212DJ+ is a quad SPST CMOS analog switch with four normally open, independently controlled circuits, a 175 ohm on resistance, and a 16-pin PDIP package. It accepts positive and negative supply voltages from ±4.5 V to ±18 V, making it suitable for routing bipolar analog signals across industrial, instrumentation, communications, and test systems. Each switch provides 1:1 signal-path routing and is controlled by CMOS-compatible logic inputs. A CMOS analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. Within the signal-chain hierarchy, it belongs to the switch and multiplexer family, which falls under interface ICs and ultimately supports the wider category of semiconductor signal-routing components. Unlike a mechanical relay, the DG212DJ+ changes state electronically without mechanical moving parts, making it appropriate for compact systems requiring fast, repeatable routing. The DG212 family provides four independent SPST switches in one package. Its stated 175 ohm on resistance is suitable for moderate-impedance signal paths, while the single-pole, single-throw configuration provides a straightforward open-state isolation path. The broad ±4.5 V to ±18 V supply range supports both single-supply arrangements with an appropriate ground reference and dual-supply systems that carry bipolar signals. Latch-up protection is specified when power is disconnected while input signals remain connected. The DG212 uses normally open switches, meaning each signal path is disconnected until its corresponding control input is asserted. The DG212 and DG202 families share the quad SPST format, but their control logic differs: the DG212 has inverted control relative to the DG202. This distinction must be checked against the existing logic levels and polarity before replacing a device on a PCB. Typical uses include precision signal routing in test and measurement equipment, multiplexed sensor acquisition, bipolar audio and communication paths, sample-and-hold systems, and industrial control modules. Because the device supports ±18 V supplies and four switch circuits, it can reduce the number of external discrete switches required in a compact analog front end. The principal design consideration is signal-path loading. With 175 ohm on resistance, the switch contributes to source and destination impedance, so downstream input impedance and cable capacitance should be evaluated together. Keep control traces away from sensitive analog inputs, observe the specified supply sequencing conditions, and use the manufacturer pin-description table when assigning PCB tracks. This page combines the manufacturer product description, distributor package information, cross-reference findings, practical application guidance, and drop-in comparison notes. It is intended to help engineers determine whether the DG212DJ+ fits the required logic polarity, voltage range, package, and analog routing performance before requesting a quotation.

RFQ پەیوەندی
DG212DY+T - Quad SPST CMOS Switch, 175Ω | Analog Devices
DG212DY+T

DG212DY+T - Quad SPST CMOS Switch, 175Ω | Analog Devices

The Analog Devices DG212DY+T is a quad SPST CMOS analog switch with four independently controlled channels, 175 Ω on-resistance, and a 16-SOIC package. It operates from dual supplies ranging from ±4.5 V to ±18 V and is intended for precision analog signal-routing applications. An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. The DG212 belongs to the CMOS analog-switch family, which sits within interface ICs and broader signal-path semiconductors. Four SPST channels provide independent selection between one switched node and one common signal path, making the device useful for sample-and-hold systems, test equipment, measurement front ends, and controlled analog routing. Key features include a 175 Ω on-resistance, 70 dB isolation, normally open operation, and dual-polarity supply support from ±4.5 V to ±18 V. The industrial-temperature version operates from -40 °C to +85 °C and is supplied in a surface-mount 16-SOIC package. Four switch circuits are integrated into one package, reducing component count while preserving separate control for each analog path. The CMOS implementation supports low-leakage signal handling and latch-up-resistant operation when power is removed while signals remain connected. Maxim guarantees that the DG202 and DG212 families will not latch up under that condition. Unlike a mechanical relay or discrete MOSFET switch, the device provides compact, fast electronic routing with no moving parts and supports negative as well as positive analog signal voltages within the supply limits. Typical applications include multiplexed instrumentation, automated test systems, audio and communication routing, data acquisition, and precision measurement circuits. Because each channel is normally open, the default state isolates the switched node until the corresponding control input is asserted. The four-control architecture allows independent routing decisions across multiple signal chains. The primary design consideration is signal range. Input and output voltages must remain within the constraints stated in the manufacturer datasheet, and control logic must be compatible with the device's active-high control scheme. Decoupling capacitors should be placed close to the supply pins, while sensitive analog traces should be kept away from high-impedance control and switching-node routes where possible. This page combines the DG212 family specifications, package and sourcing information, qualified drop-in references, and practical integration guidance. It is intended to help engineers evaluate the device faster than a generic distributor catalog entry while retaining direct access to the official manufacturer datasheet.

RFQ پەیوەندی
DG213DJ - 4-Channel 60 Ohm CMOS Analog Switch | Vishay
DG213DJ

DG213DJ - 4-Channel 60 Ohm CMOS Analog Switch | Vishay

The Vishay Intertechnology DG213DJ is a four-circuit, 1:1 CMOS analog switch with 60 ohm on-resistance, a 16-pin PDIP package, and support for signals up to ±22 V when operated from dual supplies. It also accepts single-supply operation, providing flexible routing for instrumentation, telecommunications, process-control, and computer-peripheral circuits. The switching array includes low 20 pA leakage and an 85 ns turn-on time, making it suitable for precision analog paths that require controlled impedance and fast isolation behavior. An analog switch is an integrated semiconductor device that connects or disconnects an analog signal path under digital control. Unlike a mechanical relay, it can change state rapidly without mechanical wear. The DG213DJ belongs to the analog switch, interface IC, and semiconductor hierarchy. Its CMOS implementation provides low leakage, while the 1:1 circuit configuration routes one source path to one switched output without changing the signal polarity. Key features include a 22 V supply-voltage rating, 45 ohm low on-resistance, TTL-compatible and CMOS-compatible control logic, and 20 pA low leakage. The design supports both dual-supply operation up to ±22 V and single-rail operation up to 36 V. A continuous current rating of 30 mA makes the device appropriate for instrumentation and general-purpose analog routing rather than high-current power switching. The improved charge-injection compensation helps reduce switching transients in sensitive measurement circuits. The DG213DJ uses a complementary CMOS switch architecture optimized for general-purpose signal isolation. Its low leakage limits unwanted disturbance on high-impedance nodes, while the specified 85 ns turn-on time supports reasonably fast control-response requirements. An epitaxial layer is used to reduce latch-up risk, and the low on-resistance limits signal attenuation when the switch is closed. Designers should still evaluate channel capacitance, charge injection, and off-isolation across the intended operating bandwidth. Typical applications include sample-and-hold systems, test and measurement equipment, process-control interfaces, telecommunications equipment, and computer peripherals. The device can route test, sensor, or control signals to a shared amplifier or converter. In precision systems, its low leakage and charge-injection compensation help preserve small-signal integrity, while its TTL-compatible control inputs simplify connection to legacy digital logic. A primary design consideration is ensuring that the control input levels meet the device's logic thresholds and that supply and signal voltages remain within the specified operating range. Place bypass capacitors close to the supply pins and route high-impedance signal traces away from switching-control and supply-return paths. Check absolute maximum ratings when switching signals that may exceed the nominal supply range. This page combines the manufacturer's electrical characteristics with lifecycle information, drop-in replacement analysis, application guidance, and package-specific design considerations. It helps engineers evaluate the DG213DJ for signal-routing designs, identify lifecycle risks, and plan source transitions without overlooking analog performance constraints.

RFQ پەیوەندی
DG213DY - 4-Channel CMOS Analog Switch | Vishay Intertechnology
DG213DY

DG213DY - 4-Channel CMOS Analog Switch | Vishay Intertechnology

Vishay Intertechnology DG213DY is a four-circuit, 1:1 CMOS analog switch with a typical on-resistance of 45 ohms, 60-ohm rated on-resistance, 20 pA leakage, and an 85 ns turn-on time. It is supplied in a 16-pin narrow SOIC package and supports TTL- and CMOS-compatible control logic. The device can operate from a single supply or dual supplies, with a 22 V supply-voltage rating. An analog switch is an integrated semiconductor that connects or disconnects signal paths under digital control. The DG213DY belongs to the analog-switch hierarchy, which includes multiplexers, demultiplexers, selectors, and switch matrices. Its four independent 1:1 circuits can route instrumentation signals, process-control inputs, or peripheral signals while presenting a high-impedance state when a channel is turned off. The on-resistance specification of 45 ohms and leakage specification of 20 pA help engineers balance insertion loss, signal integrity, and off-channel isolation. Key features include a 22 V supply-voltage rating, TTL- and CMOS-compatible logic levels, 45-ohm low on-resistance, 20 pA low leakage, an 85 ns fast turn-on time, single-supply operation, and an extended temperature range. The improved charge-injection compensation design reduces switching transients, while the epitaxial construction helps prevent latchup. A continuous current rating of 30 mA allows the switch to handle low-power analog and instrumentation signals without exceeding its specified current limit. The DG213DY uses complementary CMOS circuitry to provide low power consumption and bidirectional signal paths when the supply configuration permits it. Its wide operating-voltage range makes it useful in systems that need to select between positive, negative, or ground-referenced signals. Engineers should still observe the datasheet limits for supply voltage, logic levels, analog signal range, and continuous current because the switch is intended primarily for low-voltage, low-current routing rather than power switching. Typical applications include telecommunications signal routing, process-control systems, computer-peripheral interfaces, test and measurement equipment, data-acquisition systems, and industrial control modules. The 16-pin narrow SOIC package supports compact PCB layouts, while the four switch circuits allow one device to replace several discrete switching functions. The 30 mA continuous-current capability is suitable for instrumentation signals but does not make the device a power-switching solution. When laying out a DG213DY circuit, place the device close to the routed signals and provide a stable, low-impedance bypass connection between its supply pins and ground. Keep sensitive analog traces short, avoid using the analog switch to carry current outside the specified range, and observe the control-logic thresholds before changing system voltage levels. Check the pin configuration and truth table in the manufacturer datasheet when connecting control signals or supplying from a single rail. This product page combines the manufacturer electrical characteristics, verified distributor identification, package details, drop-in replacement analysis, and practical guidance for signal-routing and layout decisions. It also distinguishes the original DG213DY from lead-free and alternate packaging identifiers so procurement teams can evaluate board compatibility and lifecycle needs without changing the circuit footprint.

RFQ پەیوەندی
DG271AK - 4-Channel 50Ω SPST Analog Switch | Vishay
DG271AK

DG271AK - 4-Channel 50Ω SPST Analog Switch | Vishay

Vishay Siliconix DG271AK is a high-speed quad monolithic SPST CMOS analog switch with four independently selectable switch circuits in a 16-CERDIP through-hole package. The device provides a 1:1 signal configuration, a maximum listed on-resistance of 50 Ω, and TTL/CMOS-compatible control inputs. It is intended for routing low-frequency analog signals where low leakage, fast switching, and low charge injection are important. According to the manufacturer datasheet description, its 55 ns turn-on time supports high-speed control sequences. An analog switch is a semiconductor device that uses control inputs to connect or disconnect signals within a circuit. Unlike a mechanical relay, it can operate rapidly without mechanical wear. The DG271AK belongs to the CMOS analog-switch hierarchy, where multiple single-pole single-throw switches provide signal routing for test systems, data-acquisition equipment, instrumentation, communications, and embedded control systems. Each channel on the DG271AK forms a 1:1 path between its corresponding input and output. The DG271AK's four independent SPST channels allow one package to handle several routing points while reducing the number of discrete controls. Its listed 55 ns turn-on time, 5 pC charge injection, 32 Ω on-resistance feature, and 50 pA low-leakage figure support fast transitions and low disturbance on sensitive analog nodes. TTL/CMOS-compatible logic levels simplify control from common digital systems. Reduced switching glitches and fast settling times are also identified as principal device features. Internally, the monolithic CMOS construction places four switching elements and their control functions on one integrated circuit. This architecture is appropriate when a design requires predictable signal isolation and compact routing rather than the very low resistance of a mechanical relay. The switching path is bidirectional, making the DG271AK suitable for connecting sources, amplifiers, filters, and measurement inputs where signal flow may need to be reversed or selected dynamically. Typical uses include automated test equipment, oscilloscope and multimeter input routing, sensor multiplexing, sample-and-hold systems, communication interfaces, and industrial control modules. The 16-CERDIP package is suited to through-hole assemblies and legacy or extended-temperature equipment rather than compact surface-mount consumer products. The ceramic DIP construction provides a mechanically robust option where solder-joint reliability and insertion into through-hole sockets are priorities. Designers should account for the 50 Ω maximum listed on-resistance when cascading switches or driving a high-impedance following stage. Keep control traces away from sensitive analog paths, provide a defined logic state during power-up, and observe the absolute maximum supply and signal voltages in the manufacturer datasheet. When replacing a switch, verify control polarity, supply voltage, channel configuration, package dimensions, and the exact pinout rather than relying only on the DG271 family name. This product page combines the functional characteristics, package constraints, sourcing guidance, drop-in alternatives, comparison points, and practical routing considerations needed to evaluate the Vishay Siliconix DG271AK for a new analog-switch design.

RFQ پەیوەندی
DG301ABA - Dual SPST CMOS Analog Switch | Vishay
DG301ABA

DG301ABA - Dual SPST CMOS Analog Switch | Vishay

The Vishay Intertechnology DG301ABA is a dual SPST, TTL-compatible CMOS analog switch in a 10-pin TO-100 package. It supports bipolar supply operation from ±5 V to ±18 V and can also operate from a single supply when the V− rail is connected to 0 V. Typical power consumption is 3.5 mW, making the device suitable for compact, battery-powered analog signal-routing circuits. An analog switch is a semiconductor device that uses control logic to connect or disconnect analog signals. The SPST configuration provides one normally open switch path per channel, while the dual-channel package allows two independently controlled routes. In the power-management hierarchy, this component belongs to the interface-IC category because it manages signal connectivity rather than regulating voltage or processing digital data. The DG301ABA provides break-before-make switching behavior, preventing the input and output terminals from momentarily connecting together during a transition. Its switch-control inputs are compatible with both TTL and CMOS logic. Low charge injection reduces the unwanted voltage transient that can occur when control signals change and is important when switching precision analog signals. Operation across ±5 V to ±18 V provides flexibility for systems using split analog supplies as well as lower-voltage designs using a single supply. The typical 3.5 mW power consumption supports battery-powered circuitry where switching losses and standby power materially affect energy budget. The control architecture is designed to preserve signal isolation during switching transitions. Typical uses include battery-powered measurement systems, precision analog signal selection, data-acquisition front ends, test equipment, and general-purpose routing of low-frequency analog signals. The logic-compatible control inputs also make the device convenient for systems where CMOS or TTL digital controllers select among external sensor or conditioning circuits. Designers should confirm the exact pin configuration and switch state from the manufacturer datasheet before layout. The break-before-make timing must be considered when a downstream circuit cannot tolerate two paths being connected briefly. Input and output signal amplitudes must also remain within the device's absolute maximum and operating limits. This page combines the DG301ABA architecture, supply-range information, package details, pin-compatible family references, comparison data, and practical routing guidance. It is intended to help engineers evaluate the device for analog switching, select a suitable replacement, and plan PCB implementation without relying on incomplete catalog summaries.

RFQ پەیوەندی
DG302ACJ+ - Dual 50Ω DPST Analog Switch | Analog Devices
DG302ACJ+

DG302ACJ+ - Dual 50Ω DPST Analog Switch | Analog Devices

The Analog Devices DG302ACJ+ is a dual-channel, DPST CMOS analog switch with an on-resistance below 50 Ω, packaged in a 14-pin DIP. It supports supply voltages from ±5 V to ±18 V, accepts fully TTL- and CMOS-compatible control inputs, and provides break-before-make switching with low charge injection. These characteristics make the device suitable for routing low-frequency analog and instrumentation signals where predictable switching behavior and minimal control-input burden are important. An analog switch is an integrated semiconductor device that connects or isolates circuit nodes under digital control. The DPST configuration provides one normally closed and one normally closed? No—the DG302 family uses break-before-make switching behavior. In system-level terms, the part belongs to the analog switch and multiplexer hierarchy, where it sits between signal sources and downstream measurement or processing circuits. Unlike a mechanical relay, it changes state electronically without mechanical wear. The DG302ACJ+ combines low power operation with fast switching characteristics and strong DC and AC switch performance. Its on-resistance is specified as less than 50 Ω and is described as essentially constant across the analog signal range. Fully TTL- and CMOS-compatible control inputs simplify interfacing with microcontrollers, logic families, and test equipment. Break-before-make operation prevents the two switch paths from momentarily connecting together during a transition, while low charge injection helps limit unwanted transients on sensitive signals. The Analog Devices DG302A family is designed for battery-powered circuitry and operates from ±5 V to ±18 V. The manufacturer also identifies the DG300 through DG303 and DG300A through DG303A families as electrically compatible and pin compatible with original-manufacturer devices. That family-level compatibility is useful for industrial-control, instrumentation, test-and-measurement, and legacy equipment designs, although individual device ratings must be checked before substitution. Typical uses include switching sensor outputs, selecting test paths, routing multiplexed measurement channels, and controlling bipolar analog signals in laboratory or industrial equipment. The device is particularly useful when the control system uses TTL or CMOS logic and the switched signal remains within the device's supported voltage and signal-range limits. Designers should preserve adequate supply decoupling and route sensitive analog traces away from high-current switching paths. Because this is a through-hole DIP device, its relatively large package and lead spacing make it especially appropriate for legacy-style PCBs, prototyping systems, and repair assemblies rather than compact mixed-signal layouts. This page combines the DG302A family specifications with practical routing guidance, verified drop-in candidates, and a parameter-by-parameter comparison. It also distinguishes the exact DG302ACJ+ ordering code from nearby DG302-family devices so engineers can identify a pin-compatible replacement without overlooking package, qualification, or supply details.

RFQ پەیوەندی
DG309CJ+ - Quad SPST Normally Closed Analog Switch, 60 Ohm | Maxim Integrated
DG309CJ+

DG309CJ+ - Quad SPST Normally Closed Analog Switch, 60 Ohm | Maxim Integrated

The Maxim Integrated DG309CJ+ is a quad single-pole single-throw (SPST) CMOS analog switch with normally closed (SPST, NC) contacts, 60 ohm typical on-resistance, and approximately 130 ns switching speed, packaged in a 16-pin PDIP (0.300 inch, 7.62 mm) plastic DIP. It is the normally closed companion to the DG308A, which is normally open. An analog switch is a voltage-controlled semiconductor device that routes analog signals between circuit nodes using MOSFET pass elements rather than mechanical contacts. In the taxonomy of electronic components, a DG309CJ+ belongs to the analog switch family, which sits under interface ICs, alongside multiplexers, demultiplexers, and matrix switchers. Because it uses CMOS pass transistors instead of relay contacts, it offers near-solid-state reliability, microsecond-to-nanosecond switching, and negligible signal degradation when the supply rails are respected. Key features include a low 60 ohm on-resistance across the analog range, turn-on time below 120 ns, turn-off time below 90 ns, and very low power dissipation of about 30 nW per closed channel. Inputs are CMOS logic compatible, and the switch supports full rail-to-rail analog signal range operation. Supply options include split rails of plus/minus 5 V to plus/minus 20 V, or a single positive supply of +5 V to +30 V, with a 15 V analog input range. Internally the DG309CJ+ is a monolithic CMOS design. Each normally closed element places a pass transistor in the conducting path so the source and drain are bridged when the control input is low, which is why the part behaves as a shorting analog switch rather than a series isolator. That architecture makes it useful as a signal-shorting or bypass element in sample-and-hold circuits, guidance and control systems, communication systems, and test equipment, where a default connection must remain present when logic is unpowered or de-asserted. Typical applications include heads-up display and military radio signal routing, PBX and PABX switching networks, guidance and control system multiplexing, sample-and-hold front ends, and general-purpose bench test switching. Because the closed state is the default, it is especially suitable for fail-safe signal paths where an open circuit would be more damaging than a shorted one. When designing around the DG309CJ+, always verify the logic polarity of the control input for each channel and confirm that the maximum analog input voltage is not exceeded during transients. Because the package is a through-hole PDIP-16 rather than a surface-mount part, it is also easier to prototype and hand-solder, but requires plated through-holes and more board area than an equivalent surface-mount switch. This page consolidates distributor pricing as of 2026-10-30, verified drop-in alternatives from Maxim, Vishay and Harris, and practical design notes that go beyond the raw parameter table in the manufacturer data sheet.

RFQ پەیوەندی
DG309CY+ - Quad SPST 100 Ohm Analog Switch | Analog Devices
DG309CY+

DG309CY+ - Quad SPST 100 Ohm Analog Switch | Analog Devices

Analog Devices DG309CY+ is a quad, single-pole, single-throw CMOS analog switch with normally closed contacts, 100 ohm on-resistance, and four independent 1:1 signal paths in a 16-pin SOIC package. The device is intended for routing low-voltage analog and digital signals where the default connected state must remain closed when no switching command is applied. An analog switch is an interface IC that connects or isolates circuit nodes under digital control. It sits between signal sources and destination circuitry within a larger interface or signal-routing architecture. Unlike a mechanical relay, the DG309CY+ uses CMOS electronics to provide compact, fast, low-power switching, making it suitable for test equipment, data acquisition, instrumentation, and embedded control systems. The DG309CY+ provides four analog switch channels, a 1:1 signal configuration, and 100 ohm on-resistance. Its normally closed operation allows a default signal path to remain connected before the control input is asserted. The 16-pin SOIC package is a surface-mount package that supports conventional PCB assembly, while the exposed package dimensions are not established by the listed product information. The DG309CY+ is designed for single-pole, single-throw signal routing, not for power switching or high-voltage isolation. Its practical performance depends on the applied signal range, control logic levels, switch charge injection, off leakage, and the impedance of the connected circuit. Those electrical characteristics must be taken from the manufacturer datasheet before finalizing signal-integrity or timing budgets. Typical uses include analog test-point selection, sensor signal routing, sample-and-hold interfacing, communication path selection, and control of multiple peripheral inputs. A normally closed switch is especially useful where loss of control power or a defined inactive state should preserve the original connection rather than isolate the signal path. For PCB implementation, place the device close to the switched nodes to minimize trace resistance and coupling between adjacent channels. Confirm control-pin logic and signal limits against the manufacturer datasheet, and check continuity behavior during power-up. Do not assume that a low on-resistance makes the switch suitable for high-current loads. This product record combines the exact catalog identity, package, switch configuration, and resistance data with practical guidance for routing, signal integrity, lifecycle review, sourcing, and drop-in replacement evaluation. It also distinguishes the verified device facts from specifications that must be checked in the manufacturer datasheet.

RFQ پەیوەندی