Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
DG309DJ - Quad SPST Analog Switch | Maxim Integrated
Maxim Integrated DG309DJ is a four-circuit, 1:1 CMOS analog switch with a maximum on-resistance of 100 ohm, supplied in a 16-pin PDIP package. Each circuit provides one normally closed single-pole single-throw path, allowing the connected signal to pass when the control input is inactive and disconnecting it when the switch is actuated. An analog switch is an electronic routing component that connects or isolates signal paths under digital control. Its broader hierarchy is CMOS analog switch, analog multiplexer or demultiplexer, interface IC, and semiconductor. Unlike a mechanical relay, the DG309DJ changes the connected state electronically and is intended for signal-routing functions in communication, guidance, control, display, radio, sample-and-hold, and test-equipment systems. The four independent circuits provide an economical way to route multiple analog signals in one package. The 100 ohm maximum on-resistance is suitable for applications where the source and load impedance do not demand exceptionally low insertion resistance. Fast switching behavior helps minimize transition time when control signals change. CMOS-compatible control inputs simplify interfacing with digital logic, while the package's through-hole PDIP-16 format supports conventional PCB assembly and prototype rework. The DG309 family supports split supplies from ±5 V to ±20 V and a single positive supply from +5 V to +30 V, according to the manufacturer product page. This operating range allows the device to be used in both dual-rail analog circuits and higher-voltage single-rail systems. Exact device ratings, switch logic levels, leakage currents, switching times, and temperature limits should be checked against the manufacturer datasheet before final circuit design. Typical uses include signal multiplexing in communication equipment, channel selection in guidance and control systems, source selection for heads-up displays, routing in military radios, sample-and-hold circuits, and general-purpose test equipment. The normally closed state can also support signal bypassing, redundant routing, or fail-safe paths where continuity is preferred when control power is absent. Designers should account for the switch's on-resistance, off leakage, charge injection, control-logic levels, and supply voltage when calculating signal integrity. Keep analog traces short, connect decoupling capacitors close to the supply pins, and verify that the control signals meet the device's CMOS-compatible input thresholds. These practices reduce loading, switching transients, and unintended coupling between routed channels. This product page combines the DG309DJ architecture, supply-range information, package details, application guidance, and replacement considerations into a design-focused guide. It helps engineers identify the correct normally closed function, verify the 16-pin footprint, and distinguish it from normally open, multiplexer, and different-package alternatives before beginning PCB or firmware work.
DG309DY+ - 4-Channel SPST Analog Switch | Analog Devices
Analog Devices DG309DY+ is a four-circuit, normally closed, single-pole-single-throw CMOS analog switch with 100 Ω on-resistance, 1:1 signal routing, and a 16-pin SOIC package. It operates from 5 V to 30 V or from ±5 V to ±20 V, making it suitable for bipolar instrumentation and industrial control systems. The manufacturer reports turn-on time below 120 ns, turn-off time below 90 ns, and channel on-resistance of 60 Ω. An analog switch is an integrated semiconductor device that routes signals between an input terminal and an output terminal under digital control. The DG309DY+ belongs to the CMOS analog-switch hierarchy, which includes SPST, SPDT, and multiplexed switching products. Its four normally closed channels remain connected when the control input is inactive and disconnect when commanded, making the device useful for signal isolation, test-point routing, and channel selection. Key features include four independent SPST channels, normally closed operation, low on-resistance, fast switching transitions, CMOS-compatible control inputs, and operation across both positive supply and dual-supply rails. The 100 Ω resistance shown in the distributor catalog and the 60 Ω channel resistance reported on the Analog Devices product page describe different aspects of the published device performance; consult the manufacturer datasheet for the exact test conditions and applicable limits before finalizing a high-impedance design. The DG309DY+ uses CMOS construction to reduce input current and provide TTL-compatible control operation. Four channels in one package reduce board area compared with four discrete mechanical or relay-based switches. Because each switch has a finite on-resistance and off leakage, the selected switch must be checked against source impedance, capacitance, signal level, and the allowable insertion loss of the application. Typical uses include battery-powered test equipment, data-acquisition systems, sample-and-hold isolation, analog signal multiplexing, industrial controllers, and communication equipment. Positive-only operation at 5 V to 30 V is useful when only one supply rail is available, while ±5 V to ±20 V operation supports bipolar signals that must pass through the switch without shifting to a single-ended reference domain. For layout, keep input and output traces short, place the device close to the signal source, and avoid long unprotected routes adjacent to fast-switching nodes. Confirm the control-logic levels, supply sequencing, and absolute maximum ratings in the manufacturer datasheet before applying power. This page organizes the DG309DY+ specifications, verified package details, application guidance, pin-compatible alternatives, and practical comparison points into one engineering-focused reference for analog-signal routing designs.
DG381ACJ+ - Dual SPST 50 Ohm Analog Switch | Analog Devices
The Analog Devices DG381ACJ+ is a dual-circuit CMOS analog switch with two 1:1 SPST channels, a typical on-state resistance of 50 ohms, and a 14-pin PDIP package. It supports dual supply voltages from ±5 V to ±18 V, operates across the 0°C to +70°C commercial temperature range, and provides approximately 250 ns turn-off and 300 ns turn-on switching times. The device is intended for general-purpose signal routing in analog, instrumentation, communication, and test systems. An analog switch is a voltage-controlled semiconductor that connects or isolates circuit nodes using low-impedance CMOS transmission gates. The DG381 belongs to the analog switch and multiplexer hierarchy within interface ICs and power-management-adjacent signal-path components. Its two independent single-pole, single-throw channels allow a source signal to be routed to one destination at a time, making the device useful when a compact, logic-controlled routing element is required. The DG381ACJ+ provides a 50-ohm on-state resistance, approximately 6 pF of switch capacitance, and dual-rail operation extending to ±18 V. These characteristics are important for systems that switch moderate-amplitude analog signals rather than high-current loads. The 0°C to +70°C rating identifies the device as a commercial-temperature component, so applications requiring extended industrial or automotive temperature coverage need separate qualification. Internally, the device uses CMOS circuitry to control the analog channels. A specified on-resistance value alone does not determine signal fidelity; channel matching, capacitance, switching time, leakage, off-state isolation, and crosstalk also affect performance. The published crosstalk rating of -74 dB at 500 kHz indicates isolation between channels at that test frequency. Designers should account for these dynamic characteristics when routing fast edges, low-level signals, or sources connected through long PCB traces. Typical uses include sensor selection, sample-and-hold paths, measurement-signal routing, dual-channel test interfaces, and control systems that need two independently controlled analog paths. The device can also serve as a compact isolation element between a source and destination stage when the controlled signal lies within its supply-voltage range. A dual supply permits bipolar signal handling, while single-ended operation may also be possible depending on the circuit configuration described in the manufacturer datasheet. For PCB implementation, preserve short analog traces and place input and output decoupling close to the device. Treat the control pins as digital signals that should not be allowed to overshoot the supply rails. Check absolute maximum voltage and current limits before switching unusual waveforms, and account for injected charge and off-state leakage when the switched source has a high impedance. This product page combines the DG381ACJ+ electrical characteristics, package and supply limits with verified drop-in references and practical circuit guidance. It is intended to help engineers identify whether the dual SPST topology, switching speed, resistance, and commercial temperature rating match a specific analog-routing design.
DG381CJ - CMOS Analog Switch IC | Analog Devices
Analog Devices DG381CJ is a general-purpose CMOS analog switch IC listed in stock at LCSC, with a verified starting price of $1.1653 per unit. The device belongs to the analog-switch category, where CMOS-controlled switches route signals between circuit nodes without continuously conducting current. The verified source identifies the DG381 family as general-purpose CMOS analog switches, while the DG381CJ ordering code is associated with a DIP-14 package. Its detailed supply-voltage rating, channel configuration, on-resistance, leakage current, switching time, and logic thresholds were not included in the supplied data and must be confirmed in the manufacturer datasheet before design release. A CMOS analog switch is a semiconductor interface device that uses electronic control signals to connect or disconnect an analog signal path. The broader hierarchy is analog switch → analog multiplexer or demultiplexer → interface IC → semiconductor. General-purpose versions are selected when a compact board needs programmable signal routing for instrumentation, test, communications, industrial control, or data-acquisition systems. Unlike a mechanical relay, an analog switch changes state electronically; unlike a continuous analog amplifier, it primarily controls signal-path connectivity. The most important verified attributes are the in-stock listing, the $1.1653 starting unit price, the general-purpose CMOS technology classification, and the DIP-14 package associated with the ordering code. These attributes support cost-sensitive prototype and production sourcing, but they do not establish electrical interchangeability by themselves. Before using DG381CJ in a precision measurement path, engineers should verify channel count, normally-open or normally-closed behavior, signal polarity, bandwidth, insertion loss, charge injection, off-state isolation, and maximum analog signal excursion. The DG381 family uses integrated MOS transistors as analog switching elements controlled by CMOS-compatible logic. In a typical circuit, the control pins receive host-generated enable signals while the switched terminals carry analog or digital signals. Because a physical switch has finite resistance, capacitance, leakage, and switching transients, layout and control timing can affect measurement accuracy. The exact architecture, truth table, logic thresholds, and timing values must be taken from the DG381 manufacturer datasheet rather than inferred solely from the distributor listings. Potential uses include automated test equipment, data-acquisition front ends, industrial sensor interfaces, communication routing, laboratory instrumentation, and embedded control systems where multiple signal paths must be selected under software control. A suitable design must keep every signal and control voltage inside the device's documented limits. It should also provide clean supply decoupling and keep high-impedance routing paths short enough to limit capacitive loading and pickup. The primary design consideration is verification of the exact DG381CJ electrical table before schematic sign-off. Cross-reference search results describe DG381ACJ+ and DG300ACJ+ as complete replacements with consistent terminals and packages, but the supplied excerpts do not expose their individual voltage, resistance, timing, or leakage ratings. Engineers should therefore treat those parts as candidate drop-ins and compare every operating limit and timing parameter against the authoritative datasheet. This page consolidates the verified stock and price evidence, candidate pin-compatible replacements, package information, and practical validation guidance into one engineering-focused resource. It also distinguishes confirmed facts from unavailable specifications so procurement and design teams can make a documented decision rather than relying on an incomplete distributor summary.
DG384ACJ - Dual CMOS Analog Switch, 15V | Maxim Integrated
The Maxim Integrated DG384ACJ is a dual general-purpose CMOS analog switch designed for signal-routing applications. It is housed in a 16-pin DIP package and is associated with a maximum supply rating of 15V and an on-resistance of 50 ohms. The part combines low-power CMOS operation with a conventional dual-switch configuration, making it suitable for routing analog signals in instrumentation, test equipment, control systems, and signal-conditioning circuits. A general-purpose CMOS analog switch is an integrated semiconductor device that connects or disconnects an analog signal path under digital control. Unlike a mechanical relay, a solid-state analog switch changes state rapidly without mechanical wear. Within the broader semiconductor hierarchy, analog switches belong to interface ICs and support the signal-path functions required by measurement, communication, industrial-control, and mixed-signal systems. The DG384ACJ uses an integrated 16-pin DIP package and is specified as a dual analog switch with a 15V maximum voltage. A reported on-resistance of 50 ohms makes it relevant to designs where the switch resistance is acceptable relative to the input impedance and signal amplitude. The CMOS implementation also supports low-power operation when the application does not require continuously switching the analog path. The DG384ACJ can be used to select one of two signal sources, connect an instrumentation node to a measurement circuit, or provide controlled isolation between circuit sections. Because the on-resistance contributes to channel loss and can introduce distortion with high-frequency signals, the surrounding amplifier and source impedances must be considered carefully. The device is also intended for positive supply operation, based on its 15V rating. Typical uses include automated test equipment, data-acquisition systems, analog signal selectors, laboratory instruments, industrial controllers, and communication-interface boards. In these systems, the switch can reduce the number of external relays or mechanical contacts while providing faster operation and compact PCB placement. Layout should keep the analog input and output traces short, provide a low-impedance return path, and place the device close to the switched node. Supply bypassing and protection should follow the circuit conditions present at each analog pin. This product page combines the documented device characteristics with practical guidance for footprint reuse, signal-path planning, procurement, and drop-in replacement assessment.
DG401AK - Dual High-Speed SPST Analog Switch | Vishay
The Vishay Siliconix DG401AK is a dual, normally open CMOS analog switch with two independent SPST circuits, a 1:1 signal configuration, 35 ohm on-resistance, and a 16-pin CERDIP package. It is designed for low-power, high-speed signal routing where low insertion resistance, compact logic-driven control, and reliable packaged operation are important. An analog switch is a semiconductor device that uses digital control signals to connect or disconnect analog signal paths. The DG401AK belongs to the analog switch and switch-matrix hierarchy, where the SPST configuration provides one selectable path per circuit. Its CMOS implementation supports low-power operation and high-speed switching, making the device suitable for test equipment, signal routing, instrumentation, and communication systems. The principal features are two switch circuits, normally open SPST behavior, a 1:1 routing configuration, and a specified 35 ohm on-resistance. These characteristics allow it to serve as a building block in larger switch matrices and signal-selection networks. The CERDIP package provides a through-hole mechanical format and is intended for applications where leaded components and conventional PCB assembly methods are preferred. The DG401AK uses independent control and common-source switching structures within a dual analog-switch package. Because each channel is normally open, the default state presents a high-impedance path until the corresponding control input activates its channel. The low-power CMOS architecture is particularly useful when system power consumption, switching speed, and signal-path isolation must be balanced in the same compact package. Typical uses include multimeter and oscillometer signal selection, automated test equipment, data-acquisition front ends, sample-and-hold systems, analog signal routing, and communication or instrumentation interfaces. In each application, the DG401AK can isolate unused signal branches or connect a source to a downstream measurement channel while the control logic determines the active path. Designers should pay close attention to the 35 ohm on-resistance and the complete timing, voltage, and logic-level specifications in the manufacturer datasheet. Place the device so that sensitive analog traces remain short, provide adequate return paths, and account for off-state leakage, control timing, and switch capacitance when establishing signal-integrity limits. This product page consolidates package identification, verified distributor specifications, practical application guidance, and pin-compatible sourcing options. It is intended to help engineers compare the DG401AK with military-qualified and manufacturer-labeled versions while keeping the required 16-pin CERDIP footprint and electrical architecture in view.
DG401CJ+ - Dual 45 Ohm SPST Analog Switch | Analog Devices
The Analog Devices DG401CJ+ is an improved dual high-speed analog switch with two independent SPST (normally open) channels, a 45 Ω maximum on-resistance rating, and a 16-pin PDIP package. It is designed for signal-routing applications that require low distortion, fast operation, and low charge injection. An analog switch is an integrated semiconductor device that routes a signal between circuit nodes under logic control. The DG401CJ+ belongs to the analog-switch and multiplexer category, where it sits above discrete MOSFET switches and below more complex multiplexing or switching systems. Each of its two channels can connect or disconnect one signal path, making the device suitable for sample-and-hold systems, test equipment, audio routing, and data-acquisition front ends. Key electrical characteristics include a 45 Ω maximum on resistance and a 20 Ω typical value in the redesigned DG401 series. The manufacturer also specifies guaranteed on-resistance matching of 2 Ω maximum between switches and on-resistance flatness of 3 Ω maximum across the signal range. Charge injection is limited to 15 pC maximum, helping reduce switching glitches in precision measurement systems. The DG401 series uses a CMOS-style analog-switch architecture that operates equally well in either signal direction. Two separately controlled switches provide independent routing for dual-channel or differential systems. The 75 ns switching-time figure published for the DG401 series supports high-speed sampling and measurement applications where the switch must settle rapidly after a control transition. Typical uses include automated test equipment, sample-and-hold circuits, audio and video signal routing, analog measurement front ends, and instrumentation requiring two independently switched paths. The 16-pin PDIP package is suitable for through-hole prototyping, legacy industrial boards, and applications where a socketed or manually assembled package is preferred over a surface-mount option. When designing around the DG401CJ+, treat the 45 Ω on resistance as part of the signal-path impedance budget and keep control-edge layout short to limit capacitive coupling. Because the device is a normally open switch, the signal path is disconnected until the corresponding logic input is asserted. Confirm the control polarity and timing against the manufacturer pin-description table before assigning PCB nets.
DG401CY+ Dual 45Ω SPST Analog Switch | Maxim Integrated
The Maxim Integrated DG401CY+ is a dual, single-pole single-throw analog switch with a 1:1 circuit configuration, 45 Ω on-resistance, and a 16-SOIC package. It provides 150 ns switching time, 100 ns break-before-make behavior, 500 pA leakage, 15 V supply capability, rail-to-rail signal handling, and TTL/CMOS-compatible control logic. The two independent switch channels make it suitable for routing analog signals in test, measurement, communications, and instrumentation systems. An analog switch is an integrated semiconductor device that routes an electrical signal between terminals under digital control. Unlike a mechanical relay, it changes state rapidly with low switching delay and limited control power. The DG401CY+ belongs to the analog-switch hierarchy within interface ICs and is commonly used when a compact, logic-controlled signal path is required. Each SPST channel connects one signal terminal to one common terminal, providing straightforward routing for multiplexed or configurable analog front ends. The device’s 45 Ω on-resistance is suitable for many low- and moderate-impedance signal paths. The listed 150 ns switching time supports fast control-loop or acquisition sequencing, while the 100 ns break-before-make interval prevents the two sides of a switched connection from momentarily shorting together. Rail-to-rail operation allows signals to approach the supply limits, and TTL/CMOS-compatible logic simplifies connection to common digital controllers. Power capability is specified for single-supply operation from +10 V to +30 V and bipolar-supply operation from ±4.5 V to ±20 V. Low power consumption is listed at 35 µW maximum. These operating ranges give designers flexibility for laboratory instrumentation, industrial control systems, signal-conditioning modules, and communication equipment while preserving compatibility with both positive-only and split-supply architectures. Typical applications include multimeter input routing, automated test equipment, programmable signal-path modules, analog measurement front ends, sample-and-hold isolation, and communication-channel selection. Independent control inputs allow the two channels to be switched independently when a system needs one signal route at a time or coordinated routing between two external nodes. Layout and signal integrity require close attention because the on-resistance, leakage current, and switching transients can affect high-impedance or precision circuits. Keep analog traces short, use a solid ground reference, and avoid routing sensitive signals directly beneath control inputs. Confirm the complete pin configuration and operating limits against the manufacturer datasheet before finalizing the PCB footprint. This page consolidates the switch configuration, electrical characteristics, operating ranges, application guidance, and design cautions into an engineering-focused reference. It also distinguishes true pin-to-pin replacements from merely similar switch products, helping designers avoid substitutions that differ in logic polarity, supply range, pinout, or switching behavior.
DG401DJ+ - Dual 45Ω High-Speed SPST Switch | Analog Devices
The Analog Devices DG401DJ+ is a dual, high-speed, normally open SPST CMOS analog switch with two independently controlled circuits, an on-resistance of 45 Ω, and a 16-pin PDIP package. It combines TTL- and CMOS-compatible control inputs with low charge injection for applications requiring accurate signal-path switching. An analog switch is an interface IC that connects or isolates an analog signal without amplifying its voltage. The DG401 family belongs to the broader switch hierarchy that includes analog switches, multiplexers, and digital multiplexers. Its CMOS implementation provides low power consumption, while the high-speed switching characteristics make it useful in test equipment, sample-and-hold circuits, data acquisition systems, and precision signal routing. Key features include two SPST, normally open switch circuits, a 1:1 signal configuration, on-resistance below 45 Ω, turn-on time below 150 ns, and a maximum supply rating of 44 V. The control inputs accept TTL-compatible or CMOS-compatible logic. Low charge injection reduces the unwanted voltage pulse that can disturb a sampled signal when the switch changes state. The switch supports analog signals spanning up to 15 V while operating from a single supply. Its low on-resistance minimizes insertion loss and voltage drop in signal paths, while low leakage helps preserve the output when a channel is disconnected. The internal architecture is designed for low-power operation, which supports portable instrumentation and battery-powered test systems. Typical uses include high-speed signal routing, multiplexed measurement systems, sample-and-hold circuits, industrial control interfaces, and laboratory or communication equipment. The dual independent configuration allows two separate signals to be controlled with one device, reducing component count when board space is constrained. PCB design should keep analog traces short and provide a ground return close to the device. Control inputs must remain within their rated logic levels, and unused control or signal pins should be connected according to the manufacturer datasheet. Review voltage limits carefully because the 44 V maximum supply rating does not imply that all 15 V analog signals are safe under every operating condition. This page combines the manufacturer's core switch characteristics, package and electrical details, practical routing guidance, application fit, and a structured comparison with qualified same-footprint alternatives to support faster component selection.
DG401DY+ - Dual 45Ω High-Speed SPST Switch | Analog Devices
The Analog Devices DG401DY+ is a production dual, high-speed analog switch IC with two 1:1 SPST normally-open channels, 45 Ω maximum on resistance, and a 16-pin SOIC package. It combines TTL- and CMOS-compatible control inputs with low analog on resistance and switching times below 150 ns, making it suitable for precision signal-routing and test-and-measurement systems. An analog switch is an integrated semiconductor device that connects or disects signal paths under digital control. The DG401 belongs to the monolithic CMOS analog-switch hierarchy, which also includes multiplexers and demultiplexers. Unlike a mechanical relay, it changes connection state electronically and enables compact, repeatable routing of low-voltage analog signals in instrumentation, communications, and industrial control equipment. Key characteristics include two independent SPST switch circuits, 45 Ω maximum analog on resistance, and switching time below 150 ns. According to the Analog Devices DG401 product page, the redesigned DG401, DG403, and DG405 families also feature guaranteed low on-resistance matching between switches of 2 Ω maximum and guaranteed on-resistance flatness over the signal range of 3 Ω maximum. The typical on resistance is 20 Ω. The DG401DY+ uses TTL- and CMOS-compatible digital inputs, allowing its control signals to be driven by a broad range of digital logic families. Its monolithic CMOS implementation provides consistent bidirectional analog conduction when a switch is closed. The normally-open topology keeps each switched node disconnected during the off state, which helps prevent unintended signal paths in test systems and measurement circuits. Typical uses include automated test equipment, sample-and-measurement systems, instrumentation signal routing, communications equipment, and industrial control modules. Its dual-channel organization reduces the number of packages required when two independently controlled signal paths are needed. The 16-pin SOIC format supports conventional surface-mount assembly and is convenient for designs that require multiple switch functions without using a large connectorized relay. When designing around the DG401DY+, place the device close to the routed signal nodes to minimize PCB-trace resistance and capacitance. Check the absolute maximum signal and supply ratings in the manufacturer datasheet, particularly for bipolar analog signals, and use a defined control state during power transitions to prevent unwanted switching. Treat the 45 Ω maximum on resistance as a signal-loss term when calculating attenuation and bandwidth. This page combines the manufacturer specifications, sourcing guidance, pin-package details, and practical comparison information to support faster component selection. It also distinguishes true same-footprint drop-in choices from related DG401-family variants and highlights the electrical trade-offs engineers should review before replacing an installed switch.
DG401DY+T - 45Ω Dual SPST Analog Switch | Maxim Integrated
The Maxim Integrated DG401DY+T is an improved dual, high-speed CMOS analog switch with two 1:1 SPST channels, 45Ω on-resistance, and a 16-pin narrow SOIC package. The switch is manufactured for production and is supplied in tape-and-reel packaging under the +T ordering suffix. Its principal characteristics include 20Ω typical on-resistance, 2Ω maximum on-resistance matching, 3Ω maximum on-resistance flatness, and 15pC maximum charge injection. An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. The DG401 belongs to the broader CMOS analog switch hierarchy, which sits between passive interconnects and more complex multiplexers. Two independent switches provide separate routing control for signals that must not share a common terminal configuration, while the low on-resistance supports relatively low insertion loss in signal paths. The DG401 design emphasizes consistent behavior between its two channels. Guaranteed on-resistance matching of 2Ω maximum improves channel-to-channel uniformity, while 3Ω maximum on-resistance flatness helps maintain resistance across the operating signal range. The device also features low charge injection of 15pC maximum, reducing unwanted transient voltage when switching state changes. These characteristics are important in measurement, control, and signal-conditioning systems where switch-induced errors affect overall accuracy. The manufacturer identifies the DG401 as an improved dual high-speed CMOS analog switch. The 45Ω rating in distributor catalog data represents the nominal catalog on-resistance associated with this ordering configuration, while the redesigned family is also described as having 20Ω typical on-resistance. Supply-voltage information associated with the DG401 family covers 5V to 34V and dual-supply ranges of ±5V to ±17V. Typical uses include sample-and-hold signal paths, test-equipment routing, data-acquisition systems, analog measurement front ends, and dual-channel control interfaces. The two-channel structure is useful when a system needs two coordinated analog connections but does not require the channel count or architecture of a larger multiplexer. The 16-pin SOIC package also supports conventional surface-mount PCB assembly. Designers should verify control-logic levels, allowable analog signal excursions, switching timing, and supply sequencing against the manufacturer datasheet before finalizing a circuit. Keep analog traces short, connect return currents cleanly, and provide stable supply bypassing near the device. The low charge injection and controlled on-resistance are valuable, but they do not eliminate errors caused by unsuitable control timing, excessive loading, or out-of-range signal voltages. This product record combines the DG401's manufacturer specifications, distributor catalog parameters, package information, lifecycle status, and application-oriented engineering guidance. It also identifies verified same-footprint alternatives and distinguishes them from cross-package or functionally different switch architectures, helping engineers evaluate replacement decisions without changing the PCB land pattern.
DG403 - Dual High-Speed SPDT Analog Switch, 44V | Analog Devices
The Analog Devices DG403 is an improved, dual high-speed SPDT (single-pole double-throw) CMOS analog switch designed for precision, high-performance switching of analog signals, with a maximum signal voltage range of 44V permitting control of 30Vp-p signals, guaranteed on-resistance matching of 2 ohm max between switches, and guaranteed on-resistance flatness of 3 ohm max over the signal range, housed in a 16-pin SOIC package. An analog switch is a semiconductor device that passes or blocks analog signals under digital control, acting as the solid-state equivalent of a relay contact. Within the signal-chain hierarchy, the DG403 belongs to the analog switches and multiplexers family, positioned below analog multiplexers (which route many channels) and above simple pass elements, and it is a core building block of analog front-end and signal-routing subsystems in data acquisition systems. Key features include CMOS or TTL-level compatible logic activation, operation from single-ended supplies of +5V to +34V or split supplies from plus/minus 5V to plus/minus 17V, and a high-voltage silicon-gate process. Each of the two independent control inputs selects between two signal paths, providing the equivalent of two SPDT relay contacts with no moving parts. The improved redesign (originally by Maxim Integrated, now Analog Devices) added guaranteed low on-resistance matching between switches and flatness over the signal range, while the epitaxial layer prevents the latch-up associated with older CMOS technologies. The ON-resistance variation with analog signal level is quite low over a plus/minus 15V analog input range, ensuring low signal distortion. Typical applications include audio and video signal routing, precision data-acquisition channel selection, sample-and-hold circuits, and replacing electromechanical relays in industrial and instrumentation signal paths. Where two single-pole single-throw contacts are needed, the DG401 offers SPST functionality; the DG405 offers DPST. Designers should observe supply-rail headroom: analog signal swings must remain within the supply rails, and logic inputs must meet CMOS/TTL threshold levels for correct switching. This page synthesizes distributor pricing, family cross-references, and practical design notes not found in the manufacturer datasheet.
DG403CJ+ - Dual High-Speed SPDT Analog Switch | Analog Devices
The Analog Devices DG403CJ+ is a dual high-speed SPDT analog switch with two independently controlled 2:1 channels, 45 ohm nominal on-resistance, and a 16-pin plastic DIP package. It supports positive supply operation from 10 V to 30 V and bipolar supply operation from -4.5 V to +20 V, making it suitable for precision signal-routing systems that require low distortion and controlled switching behavior. An analog switch is an integrated semiconductor device that routes a signal between circuit nodes using controlled electrical resistance. The SPDT, or single-pole double-throw, topology connects one common terminal to one of two selectable terminals. As a dual analog switch, the DG403CJ+ contains two such channels, allowing a system to select among two signal paths for each switch. It belongs to the broader analog switch and multiplexer IC category within signal-chain semiconductors. Key characteristics include 20 ohm typical on-resistance, maximum on-resistance matching of 2 ohm, and maximum on-resistance flatness of 3 ohm across the signal range. The redesigned switch conducts equally well in either signal direction and provides guaranteed charge injection of no more than 15 pC. Its improved matching and flatness reduce gain variation when the selected source changes, while low charge injection limits transient errors in precision sampling systems. The DG403 family uses a low-voltage on-resistance architecture that is designed for bidirectional signal conduction. This makes the device appropriate for both source and destination switching positions. The dual-channel organization can implement a two-to-one analog multiplexer, a two-input selection network, or two independent SPDT paths when suitable control logic drives the select inputs. Designers should still account for control-logic levels, input voltage limits, and off-impedance behavior when integrating the switch with external circuitry. Typical uses include precision test and measurement systems, data-acquisition front ends, audio routing, communication equipment, and instrumentation in which two signals must be selected with limited insertion loss. Because the part is available in a through-hole 16-pin DIP package, it is also practical for legacy boards, prototype systems, repair assemblies, and industrial equipment where surface-mount conversion would require PCB changes. The principal design consideration is ensuring that signal amplitudes, supply rails, and logic thresholds remain within the operating limits defined by the manufacturer. Keep routing short to reduce parasitic capacitance, connect supply bypassing close to the device, and use a consistent ground reference between the switch and downstream circuitry. Adequate decoupling is especially important when the switch handles high-impedance sources or sampling networks sensitive to charge injection. This product page combines the manufacturer's functional description with practical switching, layout, and selection guidance. It also distinguishes genuine same-footprint family options from devices with incompatible multiplexer topologies, helping engineers avoid substitutions that fit electrically but require a different pin configuration or system architecture.
DG403CY+ - Dual High-Speed SPDT Analog Switch | Analog Devices
The Analog Devices DG403CY+ is a dual high-speed analog switch with two independently controlled SPDT channels, a maximum on-resistance of 45 ohms, and a 16-pin NSOIC package. It supports positive supply voltages from 4.5 V to 20 V and negative supply voltages from -4.5 V to -20 V, while the switch paths conduct equally well in either direction. The device is designed for precision signal-routing applications where fast operation, controlled charge injection, and low off leakage are important. An analog switch is a semiconductor device that routes an analog signal between circuit nodes under digital control. Unlike a mechanical relay, it provides faster switching and compact solid-state construction. The DG403 belongs to the SPDT switch hierarchy: each of its two channels connects one common terminal to one of two switched terminals, allowing a source to select between two destinations. This makes the device suitable for test equipment, signal-chain routing, instrumentation, and data-acquisition systems. Key characteristics include a maximum on-resistance of 45 ohms, guaranteed on-resistance matching of 2 ohms maximum, guaranteed on-resistance flatness of 3 ohms maximum, and charge injection of 15 pC maximum. The redesigned DG403 family also provides low off leakage below 5 nA at +85°C. These characteristics help limit signal attenuation, channel-to-channel resistance variation, transient switching errors, and leakage into sensitive measurement nodes. The DG403CY+ uses independent control inputs to operate its two SPDT channels, with operation supported by positive and negative supply rails. Equal on-resistance in both directions makes the switch useful for bidirectional paths, including instrumentation, automated test, data acquisition, and signal-conditioning systems. The 16-pin NSOIC package supports conventional surface-mount PCB assembly, while its two-channel architecture reduces the number of discrete switches required for dual-path routing. Typical applications include multiplexed sensor acquisition, oscilloscope and measurement-instrument signal routing, automated test equipment, sample-and-hold systems, and industrial control modules. The low charge-injection specification is particularly useful when the switched node feeds a high-impedance amplifier because it limits the control-induced voltage transient that could otherwise disturb a measurement. When laying out a board, keep the common and switched signal traces short, provide a low-impedance return path, and place supply-bypass capacitors near the device. Avoid routing high-impedance signals beside digital control traces, and account for the 45-ohm maximum on-resistance when designing voltage dividers, termination networks, or gain stages. Verify the exact pin mapping and recommended application circuit in the Analog Devices DG403 data sheet before layout release. This page combines manufacturer specifications, replacement guidance, application analysis, and practical implementation notes. It also distinguishes same-footprint upgrades from cross-package options so engineers can identify realistic drop-in choices without treating every functionally similar switch as a direct replacement.
DG403DJ+ - Dual High-Speed SPDT Analog Switch | Analog Devices
The Analog Devices / Maxim Integrated DG403DJ+ is an improved dual, high-speed SPDT analog switch with two independently controlled switches, an on-resistance below 45 ohm, and switching times below 150 ns. The device is supplied in a 16-pin PDIP package and uses TTL- and CMOS-compatible digital control inputs. An analog switch is a semiconductor device that connects or disconnects analog signal paths under digital control. The DG403DJ+ belongs to the monolithic CMOS analog switch hierarchy, where each SPDT pole can route one source node to either of two destination nodes. This makes the device useful for signal routing, sampling, test systems, measurement equipment, and audio or communication circuits that require controlled bidirectional analog paths. Key characteristics include low analog ON resistance, fast switching, and low charge injection. Charge injection is the unwanted voltage pulse produced when control charge enters the analog signal node during a transition. Because the DG403DJ+ limits this effect, it simplifies precise sample-and-hold and switched-capacitor circuits. The TTL- and CMOS-compatible inputs simplify interfacing with both older logic families and modern low-voltage digital controllers. The DG403DJ+ uses a monolithic CMOS implementation to provide low power consumption while supporting bidirectional analog conduction. The Analog Devices product page identifies the DG403 family as production devices and describes a redesigned series with guaranteed on-resistance matching of 2 ohm maximum, on-resistance flatness of 3 ohm maximum, typical on-resistance of 20 ohm, and low charge injection of 15 pC maximum for applicable family specifications. Typical uses include precision analog signal selection, sample-and-hold front ends, automated test equipment, audio routing, and instrumentation where a digital controller must select between two signal sources. Each switch can operate in either signal direction because the on-resistance is specified for bidirectional analog conduction. A practical design consideration is to keep input and output traces short and minimize parasitic capacitance around control and analog nodes. Because charge injection and switching transients are inherent to the transition process, the selected source impedance, downstream capacitance, and acquisition timing should be evaluated together rather than relying only on the 150 ns maximum turn-on time. This page consolidates manufacturer information, distributor pricing, verified same-package alternatives, and application-focused design guidance. It also distinguishes documented family-level specifications from parameters that were not present in the supplied source data, making the remaining engineering uncertainties explicit.
DG403DY+ - Dual High-Speed 45Ω SPDT Switch | Maxim
The Maxim Integrated DG403DY+ is a dual, high-speed analog switch containing two independent 2:1 SPDT circuits, with a maximum on-resistance of 45Ω, a 10V to 30V supply range, and a 16-pin NSOIC package. It also supports dual-polarity analog signals from ±4.5V to ±20V. These characteristics make the DG403DY+ suitable for precision signal routing, test systems, sample-and-hold circuits, and instrumentation where short switching times and low charge injection are important. An analog switch is a semiconductor device that routes analog signals between terminals under digital control. Within the interface-IC hierarchy, the DG403DY+ belongs to the CMOS analog-switch family and supports bidirectional signal conduction with TTL- and CMOS-compatible control inputs. Unlike a mechanical relay, it changes connection state electronically with no mechanical movement, allowing faster operation and compact implementation. The DG403DY+ combines a typical on-resistance of 20Ω with a maximum specified resistance of 45Ω. Manufacturer specifications also guarantee on-resistance matching within 2Ω and on-resistance flatness within 3Ω over the signal range. Its switching time is below 150ns, while charge injection is limited to 15pC maximum. These specifications improve signal integrity by reducing amplitude error, timing uncertainty, and unwanted switching transients. The dual SPDT architecture provides two selectable throws for each signal. Operation is symmetric, so the switch conducts equally well in either direction. The redesigned DG403 family is optimized for high-speed routing rather than high-voltage power switching. Input logic levels are compatible with both TTL and CMOS systems, which simplifies control from common digital controllers while retaining analog operating voltages of ±4.5V to ±20V. Typical uses include automated test equipment, oscilloscope and measurement front ends, sample-and-hold acquisition systems, data-acquisition modules, and precision signal-conditioning boards. The two independently controlled channels can route one measurement path to a DUT and another to an instrument or termination. For applications requiring extremely low leakage or fixed matched resistance, engineers should compare the DG403DY+ with other members of the DG400 switch family. Design the layout with short analog traces and a solid ground reference. Keep control traces away from sensitive switched nodes to minimize capacitive coupling. Account for charge injection as a transient step in the output, and use input and output buffering when the source impedance, leakage, or switching glitch would otherwise affect measurement accuracy. This page consolidates the DG403DY+ electrical characteristics, pin-compatible alternatives, application guidance, and design cautions into a practical engineering reference for selecting and implementing this high-speed dual analog switch.
DG403DY+T - Dual 45Ω High-Speed SPDT Switch | Analog Devices
The Analog Devices DG403DY+T is a dual, high-speed CMOS analog switch with two SPDT channels, 45 Ω on resistance, and a 16-pin SOIC package. The device supports ±4.5 V to ±20 V analog signal ranges and is designed for precision, high-performance signal routing where low on resistance, fast switching, and controlled channel behavior are important. The +T ordering code identifies the tape-and-reel shipping configuration. An analog switch is a semiconductor device that routes an electrical signal between circuit paths under digital control. The DG403 belongs to the analog-switch hierarchy, where the dual-SPDT topology provides two independently selectable throw paths per switch. This makes the device useful in test equipment, data acquisition, instrumentation, communication interfaces, and sampling systems that require compact, high-speed multiplexing without mechanical relay delays. The DG403 series combines a maximum on resistance of 45 Ω with switching times below 150 ns, according to the family data. Analog Devices also states that its redesigned DG401, DG403, and DG405 devices provide guaranteed on-resistance matching between switches of 2 Ω maximum and on-resistance flatness of 3 Ω maximum. These characteristics help reduce gain errors and distortion when signals pass through a selected channel. The monolithic CMOS implementation provides TTL-compatible and CMOS-compatible control inputs, low analog on resistance, low charge injection, and low power consumption. The controlled charge injection is particularly useful in sample-and-hold circuits because it limits the unwanted voltage step introduced by control transitions. Its dual-channel architecture also allows two signal paths to be switched concurrently, reducing the number of packages required in multi-channel systems. Typical uses include precision test and measurement, multiplexed sensor acquisition, industrial signal routing, communication equipment, and sample-and-hold circuits. The 45 Ω maximum on resistance is appropriate for many medium-impedance analog signals, while the sub-150 ns transition capability supports high-speed routing. Applications requiring substantially lower resistance or less signal degradation should compare the DG405 family or a dedicated low-resistance multiplexer before finalizing the design. PCB layout should keep analog traces short and provide a direct ground-return path beneath or beside the switch. Control inputs should be driven with clean CMOS-compatible logic, and unused inputs must not float. Signal amplitude and supply voltage must remain inside the datasheet limits because excessive voltage can increase distortion or compromise channel isolation. This product page combines the manufacturer’s DG403 family information with distributor listings, verified package details, application guidance, and clearly qualified drop-in alternatives. It helps engineers identify the correct 16-SOIC replacement while avoiding parts that merely provide similar switching functions but do not preserve the required footprint.
DG403DYZ - Dual 2:1 SPDT 45Ω Analog Switch | Renesas
The Renesas Electronics DG403DYZ is a monolithic CMOS dual analog switch configured as two independent 2:1 SPDT circuits, with a maximum on-resistance of 45 Ω in a 16-pin SOIC package. It supports TTL-compatible and CMOS-compatible control inputs and provides fast switching, with tON specified below 150 ns. The DG403DYZ is designed for precision signal routing where a compact, dual-channel SPDT function is required. An analog switch is an integrated semiconductor that routes electrical signals between circuit nodes under digital control. The SPDT, or single-pole double-throw, configuration connects one common terminal to one of two switched terminals. As a dual 2:1 CMOS analog switch, the DG403DYZ places two such routing elements in one package. It belongs to the broader analog-switch and multiplexer hierarchy, connecting precision measurement, test, signal-processing, and communication circuits. Key characteristics include two switch circuits, a 45 Ω maximum on-resistance rating, switching time below 150 ns, and low charge injection suitable for sample-and-hold applications. TTL- and CMOS-compatible control inputs simplify interfacing with digital controllers. The manufacturer describes the monolithic CMOS implementation as providing low analog on-resistance and improved switching performance while retaining a standard 16-SOIC footprint. The two independent SPDT channels allow a compact board to route control, measurement, or low-energy analog signals without using two separate switch packages. Because both channels share one IC, system designers can simplify routing logic and reduce component count. The Renesas datasheet also states that DG401 and DG403 pinouts are similar, permitting a standard layout for different switch functions, although the DG401 is SPST rather than a direct functional substitute. Typical uses include sample-and-hold acquisition, test-equipment signal routing, data-acquisition systems, battery-powered instrumentation, and industrial control interfaces. The DG403DYZ is especially appropriate when TTL-compatible control is useful, switching speed below 150 ns is adequate, and a 45 Ω maximum on-resistance is acceptable for the signal path. Its dual-channel arrangement can simplify designs that require two coordinated or independent routing decisions. PCB design should preserve the manufacturer's pin and footprint requirements and route each switched signal away from digital control traces where possible. Keep the analog source, drain, and common paths short, use a ground plane, and place input and output protection close to the external connector. Verify the actual signal amplitude and bandwidth against the 45 Ω on-resistance specification before using the switch in precision or high-impedance measurement paths. This product page combines the manufacturer's DG403 family information, exact ordering-code details, source links, package guidance, comparison information, and practical selection criteria. Those engineering details help distinguish a true same-footprint replacement from a merely similar analog switch and support faster design evaluation for analog routing applications.
DG405AK - Dual High-Speed 35Ohm Analog Switch | Maxim
The Maxim Integrated DG405AK is a dual, high-speed analog switch with two independently controlled SPST channels, a 2:1 circuit configuration, 35 ohm on resistance, and a 16-pin CERDIP package. It is a normally open CMOS switch designed for routing analog signals where low on resistance, controlled channel matching, and fast operation are important. The DG405 family is identified as production by the manufacturer. An analog switch is an interface IC that connects or disconnects a signal path under digital control. The DG405AK belongs to the broader analog-switch hierarchy, which includes multiplexers, demultiplexers, and CMOS switch ICs used in data acquisition, test, communications, instrumentation, and signal-routing systems. Its normally open architecture leaves each channel disconnected until the corresponding control signal activates it. The redesigned DG405 family provides guaranteed on-resistance matching between the two switches of 2 ohm maximum and guaranteed on-resistance flatness over the signal range of 3 ohm maximum. The manufacturer also identifies a typical on resistance of 20 ohm. These characteristics help reduce channel-dependent amplitude error and distortion when the same signal is routed through different switch paths. The distributed 35 ohm value identifies the DG405AK configuration and should be checked against the operating signal range during design. The DG405AK uses dual SPST CMOS switching elements and high-speed control logic. Two switches provide separate routing decisions rather than multiplexing a larger number of inputs through one common terminal. This arrangement is useful when a system must select between two signal paths, isolate a source from a downstream instrument, or implement a sample-and-hold acquisition network. Exact switching-time, voltage, leakage, and channel-count details must be confirmed in the manufacturer data sheet. Typical applications include precision signal routing in data-acquisition systems, switched-capacitor filter control, audio and communications routing, automated test equipment, and laboratory instrumentation. The matched on-resistance specification is especially valuable when comparing channels in instrumentation, while the high-speed architecture suits systems that require rapid settling between measurement or routing states. External clocking, drive levels, and control timing must remain within the device's documented operating limits. Design the surrounding circuit so that signal amplitude, bandwidth, and transient current remain compatible with the switch. Place bypass and protection components close to the supply and signal pins, and use controlled-impedance routing when signals are sensitive to reflection or crosstalk. Account for off-state isolation, charge injection, and control-logic timing when planning precision measurements or synchronous acquisition sequences. This page combines the manufacturer's DG405 family information, package and configuration details, and practical routing guidance with a pin-compatible comparison focused on military-qualified DG405 variants. It is intended to help engineers identify the correct switch configuration, verify package compatibility, and plan the surrounding analog signal path before releasing a PCB design.
DG405CJ+ - Dual 45Ω DPST Analog Switch | Maxim Integrated
The Maxim Integrated DG405CJ+ is a dual, high-speed CMOS analog switch with two 2:1 DPST normally open circuits, 45 Ω on resistance, and a 16-pin PDIP package. It is designed for routing high-frequency or low-noise analog signals in test, measurement, instrumentation, and signal-conditioning systems. The through-hole package measures 0.300 inch, or 7.62 mm, in body width and supports conventional breadboard and through-hole PCB assembly. An analog switch is an integrated circuit that connects or disconnects signal paths under digital control. The DPST configuration provides one normally open connection per switch, while the dual architecture controls two independent circuits from a shared package. As a CMOS analog switch, the DG405CJ+ combines low-power operation with bidirectional signal handling and compact integration. It belongs to the broader interface IC hierarchy, where analog switches and multiplexers route external signals into precision measurement and signal-processing systems. The redesigned DG405 family includes guaranteed matching between the two switches of 2 Ω maximum and guaranteed on-resistance flatness over the signal range of 3 Ω maximum. These matching characteristics are important when two channels are treated as differential or when signal-path resistance must remain consistent across operating conditions. The DG405CJ+ also supports a 45 Ω nominal on-resistance and normally open switch behavior for applications requiring the default path to be disconnected. Its high-speed CMOS implementation is intended for signal routing where transition time and resistance matching affect measurement accuracy. Because the device uses a bipolar CMOS process, it combines fast switching behavior with controlled off-state characteristics. Signal integrity still depends on the source and load impedance, trace geometry, supply bypassing, and whether the selected switch architecture supports break-before-make operation where required. Typical uses include precision test-and-measurement front ends, oscilloscope and communications test paths, data-acquisition systems, sample-and-hold circuits, and industrial analog multiplexing. The two switch sections can support paired routing, differential measurements, or independent channel selection. Its 16-pin PDIP format is particularly useful for legacy instrumentation, prototype boards, educational platforms, and through-hole assembly processes. For a new PCB, place the DG405CJ+ close to the signal source and destination to minimize trace capacitance and resistance. Keep analog routing away from switching-power nodes, provide a local bypass capacitor near the supply pin, and use a ground plane that supports low-impedance return current. Verify the actual control truth table, break-before-make behavior, supply limits, and maximum signal swing in the manufacturer datasheet before finalizing the layout. This product page combines package, function, matching, and application details with practical selection guidance for engineers comparing the DG405CJ+ with related dual DPST switches. The key decision is not only package compatibility but also on-resistance, leakage, switching speed, control logic, signal range, and whether the replacement is qualified for the original operating conditions.
DG405CY+ - Dual 45Ω Analog Switch | Analog Devices
The Analog Devices DG405CY+ is an improved dual high-speed analog switch with two 2:1 channels, a specified 45 Ω on-resistance, rail-to-rail signal handling, and a 16-pin SOIC package. It operates from +10 V to +30 V in single-supply systems or from ±4.5 V to ±20 V in bipolar systems, with maximum power consumption listed as 35 μW. The device supports TTL and CMOS logic-compatible control signals. An analog switch is a semiconductor interface that connects or disconnects analog signals under digital control. The DG405CY+ belongs to the analog switch and multiplexer hierarchy, where switches provide signal routing while multiplexers combine multiple inputs onto a shared output. Its low power consumption and rail-to-rail operation make it suitable for precision measurement, test equipment, communication systems, and industrial control circuits that route low-frequency or moderate-bandwidth signals. The key feature of the DG405CY+ is its pair of independent 2:1 analog channels. A low on-resistance limits signal attenuation and distortion when the switch is closed, while the 30 Ω maximum on-resistance stated for the DG405 family provides a defined performance limit. Rail-to-rail signal handling allows signals to approach the supply rails, and TTL/CMOS-compatible control inputs simplify interfacing with digital controllers, counters, and field-programmable logic. The improved DG405 family is specified with low on-resistance matching between switches, with a maximum matching value of 2 Ω, and low on-resistance flatness over the signal range, with a maximum value of 3 Ω. These characteristics reduce channel-to-channel and signal-level-dependent errors in instrumentation architectures. The manufacturer product page also identifies a typical on-resistance of 20 Ω for the redesigned family. Typical applications include multiplexed sensor acquisition, automated test equipment, sample-and-hold signal paths, audio and communication routing, and industrial control interfaces. The dual-channel organization reduces the number of switch packages needed when two independently controlled routes are required. For designs requiring more inputs on one output, the DG419 family and related analog multiplexer products offer a different multiplexing architecture rather than a direct functional substitute for the DG405CY+. Designers should account for the 45 Ω listed operating resistance and the maximum on-resistance variation when calculating insertion loss for high-impedance or precision analog nodes. Control logic must remain within the device's TTL and CMOS compatibility levels, and unused inputs should be connected according to the manufacturer pin-description table. PCB signal integrity also benefits from short routing, a continuous ground plane, and careful placement of any external protection or filtering components. This product page combines the manufacturer specifications, distributor identification, pin-package details, application guidance, drop-in alternatives, and design considerations needed to evaluate the DG405CY+ before integrating it into an analog-routing design.
DG405DY+ - Dual 2:1 CMOS Analog Switch, 45 Ohm, 16-SOIC
The Analog Devices DG405DY+ is a dual 2:1 CMOS analog switch with 45 Ohm typical on-resistance and a 16-SOIC package. The device routes analog signals through two independent switch circuits, supports analog signals up to 15 V, and is specified for a maximum supply voltage of 44 V. Its low-power CMOS design provides TTL- and CMOS-compatible control inputs, low leakage, fast switching, and single-supply operation. An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. Unlike a mechanical relay, a CMOS analog switch changes state rapidly with no moving parts. The DG405 belongs to the analog switch hierarchy, which includes multiplexers, demultiplexers, and matrix switches. These devices are widely used to route measurements, control signals, and sensor outputs between shared circuit nodes. Key electrical features include 45 Ohm typical on-resistance, 20 Ohm typical on-resistance in the redesigned DG405 series, low off leakage of 40 pA, and switch-on time below 100 ns. Charge injection is limited to 15 pC, while on-resistance matching and flatness are guaranteed to 2 Ohm and 3 Ohm maximum, respectively. These characteristics support accurate, high-speed signal routing without the switching transients associated with mechanical contacts. The DG405 uses monolithic CMOS construction to combine low power consumption with fast control response. TTL-compatible inputs simplify interfacing with legacy digital logic, while CMOS compatibility supports modern controllers. Its 44 V maximum supply rating and 15 V analog signal range provide additional headroom in industrial, instrumentation, and test systems, although the precise minimum supply voltage must be confirmed in the manufacturer datasheet. Typical uses include multiplexed measurement front ends, sample-and-hold systems, automated test equipment, and control paths where one of two signal sources must be connected to a common amplifier or converter. The device is particularly useful where switching speed and low leakage matter more than ultra-low on-resistance, such as sensor selection, video routing, and precision measurement multiplexing. When laying out a DG405DY+ board, place input and output traces short, keep analog routing paths away from high-current switching nodes, and use a ground plane that provides a low-impedance return for control and signal currents. Verify that every signal remains within the 15 V analog range and that the supply never exceeds the 44 V maximum rating. This page combines manufacturer and distributor product information, documented cross-reference alternatives, package details, application guidance, and design notes. It also identifies the verified electrical data and highlights the parameters that still require confirmation from the full manufacturer datasheet before a production design is released.
DG406CJ+ - 16-Channel CMOS Analog Multiplexer | Analog Devices
The Analog Devices DG406CJ+ is an improved 16-channel or dual 8-channel CMOS analog multiplexer packaged in a 28-pin DIP. It provides a maximum on-resistance of 100 ohms, channel matching of 8 ohms maximum, and guaranteed on-resistance flatness of 9 ohms maximum. The device accepts single-supply operation up to +30 V and dual-supply operation up to ±20 V. An analog multiplexer is an analog switch integrated with address-decoding logic that connects one of several inputs to a shared output. The DG406 family belongs to the broader switch and multiplexer hierarchy, which includes analog switches, multiplexers, demultiplexers, interface ICs, and semiconductor signal-routing components. Its CMOS construction and rail-to-rail signal handling make it appropriate for routing signals across a wide common-mode range when the signal remains within the device's stated operating limits. Key features include low charge injection of 15 pC maximum, low input leakage of 5 nA maximum at +85 °C, and low power consumption of 1.25 mW maximum. TTL-compatible digital controls simplify interfacing with common logic systems. The manufacturer identifies the improved DG406 as a pin-compatible plug-in upgrade for the industry-standard DG406 and DG407 families, making it useful when maintaining existing analog-routing boards. The internal switch array uses independently controlled analog paths to implement either one 16-channel multiplexer or two 8-channel multiplexers. Address inputs select the active channel, while an inhibit function can place the device in a disabled state. The guaranteed matching and flatness specifications help minimize gain and distortion changes when the selected channel changes, which is important in precision measurement paths. Typical uses include audio signal routing, communication systems, data-acquisition systems, guidance and control systems, sample-and-hold circuits, and test equipment. These applications benefit from the combination of multiple channels, low leakage, low charge injection, broad supply-voltage options, and compact integration. A design can use one device for a larger 16-channel bank or configure it as two separate 8-channel banks when the system requires independent routing. When designing around the DG406CJ+, verify that every routed signal stays within the selected supply range and that control levels meet the TTL-compatible input requirements. Treat the maximum on-resistance as part of the source and amplifier impedance budget, and account for charge injection when sampling rapidly changing signals. Use the manufacturer pin-description table when assigning PCB nets and verify the address and inhibit logic in the final system. This product data combines the manufacturer's device description, identified performance limits, operating applications, and replacement information into an engineering-oriented guide. It also distinguishes the device from lower-information suffix and packaging references by focusing on functional compatibility, electrical limits, and concrete design trade-offs.
DG406DJ+ - 16-Channel CMOS Analog Multiplexer | Maxim
Analog Devices DG406DJ+ is a 16-channel single-ended CMOS analog multiplexer with a maximum on-resistance of 100 ohm, housed in a 28-pin PDIP package. It accepts TTL/CMOS-compatible 4-bit address logic, provides an enable input for cascaded or multiplexed systems, and supports single supplies from +5 V to +30 V or dual supplies from ±4.5 V to ±20 V. A CMOS analog multiplexer is an analog switch network that connects one selected input signal to a common output while blocking the unselected paths. The DG406 belongs to the broader analog switch and signal-routing hierarchy, where low on-resistance, low leakage, controlled charge injection, and accurate channel matching determine how faithfully a measurement or audio signal passes through the selected channel. The DG406 family provides guaranteed channel-to-channel matching of 8 ohm maximum and on-resistance flatness of 9 ohm maximum across the specified signal range. Maximum on-resistance is 100 ohm, maximum charge injection is 15 pC, and input leakage is 5 nA at +85°C. These characteristics support consistent signal attenuation, low switching transients, and reduced measurement error across the 16 channels. Internally, the device combines 16 analog switches with a TTL/CMOS-compatible binary decoder, a logic-threshold reference, and an enable input. The four address inputs select one of 16 channels, while ENABLE controls participation in a larger multiplexed system. The DG406 and DG407 families are positioned as pin-compatible plug-in upgrades to the established DG406 and DG407 industry-standard devices. Typical uses include high-speed data-acquisition systems, automated test equipment, audio routing, avionics, battery-operated instrumentation, and remote measurement platforms. The DG406DJ+ is especially suitable when one analog source must be selected from 16 inputs while keeping channel resistance and capacitance matching under control. Design the interface around the supported supply range, logic thresholds, address sequencing, and enable timing. Check the maximum signal voltage, ensure every analog pin remains within the supply rails, and account for charge injection when changing channels. A through-hole PDIP footprint also requires adequate board spacing and routing clearance around adjacent high-impedance nodes.