Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
DG413DY+T - Quad SPST Analog Switch | Maxim Integrated
The Maxim Integrated DG413DY+T is a monolithic quad SPST CMOS analog switch designed for low-voltage signal routing in test, measurement, communication, and instrumentation systems. It provides four independent single-pole throw switches with normally open and normally closed contacts, a 1:1 multiplexing arrangement, 35 ohm on-resistance, and a 16-pin SOIC package. The device is suitable for analog and digital signal switching where a compact, low-power multiplexer is required. An analog switch is an electronic routing component that connects or disconnects signal paths under digital control. The DG413DY+T belongs to the broader multiplexer and demultiplexer hierarchy within interface ICs. Its CMOS control inputs are compatible with TTL and CMOS logic, allowing the four channels to be operated independently from a microcontroller, FPGA, or test-system controller. Key features include low on-resistance matching between switches, with a maximum variation of 3 ohms, and guaranteed on-resistance flatness across the signal range of up to 4 ohms. The device also features low charge injection, low power consumption, and ESD tolerance of at least 2000 V per Method 3015.7. These characteristics help preserve signal integrity when the same analog path is shared by several measurement or control channels. The DG413DY+T is designed around a monolithic quad-SPST architecture. Each switch uses separate control and signal terminals, making it possible to route one source to one destination or disconnect a signal completely. The low leakage specification of 250 pA maximum helps limit unwanted coupling between high-impedance nodes when a switch is open. The 16-SOIC package supports conventional surface-mount PCB assembly while keeping the four channels in a compact layout. Typical uses include battery-powered test equipment, data-acquisition systems, analog signal conditioning, sample-and-hold circuits, communication routing, and industrial control systems. The device is especially useful when a design needs flexible selection between normally open and normally closed paths, controlled isolation of unused inputs, or independent switching of several low-frequency analog signals. For PCB design, keep control traces away from high-impedance signal nodes and route analog inputs and outputs with short, symmetric traces. Confirm the supply voltage, logic thresholds, signal range, and operating temperature against the manufacturer datasheet before production release. This page combines device specifications, sourcing guidance, compatible alternatives, and practical analog-switch design considerations for faster engineering evaluation.
DG413DYZ - 35 Ohm Quad SPST Analog Switch | Renesas
Renesas Electronics DG413DYZ is a monolithic quad SPST CMOS analog switch with four independent, single-pole single-throw channels, a 35 ohm on-resistance, and a 16-pin SOIC package. The switch supports bidirectional signal conduction, TTL-compatible and CMOS-compatible digital control inputs, and switching suitable for analog routing, audio selection, instrumentation, and data-acquisition systems. An analog switch is an integrated semiconductor device that connects or isolates analog signals under digital control. The DG413 belongs to the analog-switch hierarchy, where an SPST channel provides one signal path that can be opened or closed. Four independent channels permit simultaneous routing of unrelated signals without sharing a common multiplexer node. Bidirectional operation allows each channel to carry a signal in either direction. The DG413DYZ combines a maximum on-resistance of 35 ohms with a turn-on time of 175 ns. Its four independent SPST switches support TTL and CMOS-compatible control logic, making the device suitable for systems using microcontrollers, FPGA control signals, comparators, or other digital controllers. The compact 16-pin SOIC package supports conventional surface-mount PCB assembly. Each channel operates independently, allowing control signals to enable or disable individual routes. This architecture is useful when several analog signals must be connected to downstream circuitry without multiplexing them through a shared internal node. Low on-resistance helps limit signal attenuation, while the 175 ns turn-on time supports applications that do not require sub-nanosecond switching performance. Typical uses include audio signal routing, test and measurement systems, data-acquisition equipment, and general-purpose analog isolation. The device can also serve as a sampling-network element when a controller must connect a selected source to an instrumentation amplifier, ADC input, or measurement front end. Control-logic compatibility simplifies interface design with both 5 V CMOS systems and conventional TTL signals. For reliable layout, route high-impedance control and analog traces away from fast-switching or high-current paths, and provide a stable ground reference to all package pins. Check the exact logic thresholds, supply requirements, leakage limits, and maximum signal voltage in the Renesas DG411, DG412, and DG413 datasheet before finalizing the schematic and operating limits. This product page consolidates the manufacturer specifications, verified distributor listings, drop-in comparison options, and practical implementation guidance needed to evaluate the DG413DYZ for a new analog-routing design.
DG417AK - 35 Ohm SPST Analog Switch IC | Vishay Siliconix
The Vishay Siliconix DG417AK is a precision CMOS monolithic analog switch packaged in an 8-lead SOIC, configured as a single SPST normally-closed (NCX1) channel with a maximum on-resistance of 35 ohm and a typical on-resistance of 20 ohm. It is designed for the +/-15 V analog signal range and drives both TTL and CMOS control logic, making it a drop-in fit for legacy instrumentation and test equipment. An analog switch is a semiconductor device that routes an analog signal between circuit nodes under digital control. The DG417 belongs to the broader family of analog switches and multiplexers, which sit between sensors, amplifiers and converters on one side, and a shared signal chain on the other. A single-pole single-throw (SPST) switch provides one signal path that is either connected or broken, while a normally-closed version holds the path closed until a control signal opens it, which is the safe default for fail-safe routing. Key features include guaranteed on-resistance matching between switches of 3 ohm max and guaranteed on-resistance flatness across the signal range of 4 ohm max, both improvements over earlier generations of this device family. Fast switching action is specified at tON = 100 ns, and ultra-low power requirements of PD = 35 nW keep the supply current draw negligible in battery-backed and standalone measurement fixtures. The design is CMOS monolithic, so the part draws essentially no quiescent bias current. Because the switch is CMOS and complementary-driven, the control pins accept TTL and CMOS levels, and the input stage tolerates a wide analog signal range of +/-15 V on the switched terminals. On-resistance matching and flatness specifications are what make the device usable for precision measurement: they bound the error introduced when the same source impedance drives different switched paths, which is the dominant error term in many 16-bit and 18-bit front ends. Typical applications include sample-and-hold front ends for high-resolution ADCs, precision instrument amplifiers in test and measurement systems, audio and low-frequency signal routing in broadcast and studio equipment, medical monitoring front ends, and general-purpose routing in industrial control and data acquisition modules. The primary design consideration is the always-present 35 ohm series resistance in the closed state, which must be included in the system noise and offset budget; keep the switch close to the high-impedance input it serves so that leakage and stray capacitance do not degrade accuracy. Because the DG417AK is a legacy order code, confirm supply availability and consider the currently active equivalents listed below for new designs. This page brings together the electrical characteristics, the exact package and pinout information, drop-in replacements with quantified parameter differences, and practical layout and signal-integrity guidance that are not consolidated anywhere in the original manufacturer documentation.
DG417CJ+ - 35 Ohm SPST CMOS Analog Switch | Maxim
The Maxim Integrated DG417CJ+ is a single-pole single-throw (SPST) precision CMOS analog switch with a typical on-resistance of 35 ohm, supplied in an 8-pin PDIP package. It is designed for low-voltage analog signal routing in test, measurement, communication, and instrumentation systems. The device provides one independently controlled switch path, complementary switching behavior, low charge injection, and bidirectional signal conduction. According to the manufacturer datasheet, the DG417 family also guarantees on-resistance matching within 3 ohm maximum between switches and on-resistance flatness within 4 ohm maximum across the signal range. An analog switch is a semiconductor device that routes an analog voltage or current between circuit nodes under digital control. In system terms, an analog switch belongs to the interface IC category, where it connects to multiplexers, sample-and-hold circuits, and signal-conditioning networks. Unlike a mechanical relay, the DG417CJ+ changes state electronically without moving mechanical contacts, allowing compact, reliable, and fast signal-path control. The DG417CJ+ offers a rated on-resistance of 35 ohm, low charge injection, low power consumption, and an ESD tolerance of 2000 V. Its precision monolithic CMOS construction supports consistent switching behavior over the usable signal range. The switch operates equally well in either signal direction, making it useful where the source and destination roles can reverse during a measurement or test sequence. The device is available in a commercial temperature grade, and the 8-pin PDIP package is suitable for through-hole assembly, prototype boards, educational laboratories, and legacy industrial equipment. The DG417C version is the leaded commercial-temperature option; the '+' ordering suffix identifies the modern ordering designation used for the same device family. A companion DG417DJ and related MAX4504 devices use comparable 8-pin DIP configurations, but control polarity, voltage limits, and operating-temperature ranges must be confirmed before substitution. Typical uses include routing sensors to a measurement amplifier, selecting inputs in automated test systems, switching references in laboratory equipment, and controlling analog signal paths in communication hardware. Because the device presents about 35 ohm in the closed state, it is best suited to moderate-impedance analog nodes rather than high-current power switching or low-impedance precision-adcitor front ends where switch resistance would degrade accuracy. For layout, keep the analog signal traces short and connect the supply pins to a low-impedance ground plane. Place any bypass capacitor close to the device, avoid routing control signals beneath sensitive analog nets, and confirm that the switched voltage remains within the datasheet limits. The maximum and recommended operating voltages, supply current, leakage current, switching time, and temperature limits should be taken directly from the manufacturer datasheet for the selected part variant. This page combines package, pin, application, and substitution information with practical PCB and signal-integrity guidance. It is intended to help engineers confirm whether the DG417CJ+ fits a legacy analog-routing design before ordering a new PCB.
DG417CY+ - 35 Ohm SPST Analog Switch | Analog Devices
Analog Devices DG417CY+ is a precision, CMOS, monolithic SPST analog switch with a 35 ohm on-resistance, 8-pin NSOIC package, and normally closed contact configuration. The verified product data identifies a single switch channel, a 1:1 signal configuration, 100 ohm maximum off-leakage, and complementary 10 V to 30 V dual-supply operation or 4.5 V to 20 V single-supply operation. It is designed for precision signal routing where low distortion, controlled resistance, and reliable switching are important. An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The DG417 belongs to the broader analog switch and multiplexer hierarchy, which sits within interface ICs used for routing sensor, measurement, communications, and test signals. Unlike a mechanical relay, its CMOS implementation supports fast operation, compact integration, and low power consumption, while the normally closed configuration provides a defined signal path when the control input is inactive. The DG417CY+ is identified as an improved precision switch. The manufacturer describes on-resistance matching of 3 ohm maximum and on-resistance flatness of 4 ohm maximum across the signal range. These characteristics help preserve amplitude accuracy and linearity in systems that repeatedly route low-level analog signals. The verified distributor description lists 35 ohm on-resistance, while an additional source cites a 100 ohm maximum off-leakage figure. The switch can operate from dual supplies of 10 V to 30 V or from a single supply of 4.5 V to 20 V, allowing integration into both traditional bipolar analog systems and lower-voltage equipment. Its single SPST channel makes it particularly useful for one signal path rather than a multiplexer bank. The control and signal-pin architecture supports straightforward routing in test-and-measurement, instrumentation, communications, and precision acquisition systems. Typical uses include signal-path isolation, sensor conditioning front ends, automated test equipment, data-acquisition systems, and communication interfaces. The normally closed behavior is valuable when a default connection must remain active before a controller asserts the switch. Designers should account for charge injection, off-leakage, supply sequencing, and the dynamic behavior of the on-resistance rather than treating the switch as an ideal conductor. For PCB implementation, place the device close to the routed signal to minimize parasitic capacitance and pickup. Keep control traces away from sensitive analog inputs, provide adequate supply decoupling, and verify that the selected control logic is compatible with the device's operating supply. The 8-pin surface-mount package supports compact layouts, but normal reflow and handling practices remain necessary. This page combines the verified DG417CY+ distributor information, manufacturer product details, package information, and design-focused guidance. It also documents where additional datasheet values, exact pin assignments, pricing tiers, and verified drop-in alternatives are needed, allowing procurement and engineering teams to evaluate the part without treating unverified information as guaranteed.
DG417CY+T - 35Ω SPST Analog Switch | Analog Devices
Analog Devices DG417CY+T is a single-channel, normally closed SPST CMOS analog switch with a 35Ω on-resistance, housed in an 8-pin SOIC package. The precision switch supports positive and negative signal ranges, conducts equally well in either direction, and is designed for precision signal-routing and test-equipment applications. According to the manufacturer, its redesigned DG417 family also provides guaranteed on-resistance matching and flatness across the signal range. An analog switch is an integrated semiconductor device that routes a signal between circuit nodes under digital control. The DG417 belongs to the analog-switch hierarchy, which sits within interface ICs and broader semiconductor signal-path systems. Unlike a mechanical relay, a CMOS analog switch operates quickly, consumes little power, and can place very low resistance between a signal terminal and the common terminal. Its normally closed configuration provides a default electrical path when the control input is inactive. Key characteristics include one SPST channel, a 35Ω specified on-resistance, and an 8-SOIC footprint. The DG417 family also guarantees on-resistance matching to 3Ω maximum between switches and on-resistance flatness to 4Ω maximum over the signal range. These matching and flatness limits are important in instrumentation because they reduce gain error and distortion when signals pass through the switch. The redesigned family additionally features low charge injection, low power consumption, and symmetrical bidirectional conduction. The switch is specified for dual supply operation from ±4.5V to ±20V and for positive supply operation from +10V to +30V, depending on the device variant and test condition. These ranges permit operation from common laboratory and industrial supply rails while supporting bipolar signal paths. A separate negative supply is required when the switched signal can extend below ground. The CMOS construction controls power consumption while providing low off leakage and low on-resistance. Typical uses include precision test-and-measurement signal paths, data-acquisition systems, analog input selection, automated test equipment, and instrumentation requiring a default closed connection. The switch can also provide sample-and-hold isolation, signal isolation, or a selectable resistive branch when its on-resistance is intentionally placed in the signal path. Symmetrical conduction is useful when the source impedance is not known in advance or when either signal polarity must be handled consistently. For layout, keep the switched traces short and connect the common and terminal pins with symmetric routing where signal integrity matters. The control input must transition cleanly between valid logic levels, and unused supply pins must meet the requirements defined in the manufacturer datasheet. Because the 35Ω resistance is appreciable for precision measurement paths, account for it in gain, bandwidth, offset, and noise calculations rather than treating the closed switch as ideal. This page combines manufacturer specifications, application guidance, pin-level design considerations, and a structured comparison of verified same-package alternatives. It helps engineers distinguish electrical drop-in options from merely similar interface switches and identify the correct replacement for an existing 8-SOIC layout.
DG417DJ - 35 Ohm Precision CMOS Analog Switch | Vishay
The Vishay DG417DJ is a single SPST precision CMOS analog switch with a 35 ohm maximum on-resistance, fast 100 ns switching action, and an 8-pin plastic DIP package. The device supports analog signals up to 15 V and has a 44 V maximum supply rating, combining low power, low leakage, and compact switching for portable, industrial, and military equipment. An analog switch is a semiconductor interface that routes signals between input and output terminals under digital control. The DG417 belongs to the DG417, DG418, and DG419 family of monolithic CMOS switches. These devices occupy the interface-IC hierarchy above passive switches and analog multiplexers, providing controlled bidirectional or unidirectional signal paths in test equipment, data acquisition, battery-powered instruments, and industrial control systems. Key characteristics include a maximum on-resistance of 35 ohm, a typical on-resistance of 20 ohm, and a turn-on time of 100 ns. The low-power specification is 35 nW, while the 15 V analog signal range supports instrumentation and control signals above conventional logic levels. TTL and CMOS compatibility makes the control interface straightforward for common digital circuits. The DG417DJ uses monolithic CMOS construction to limit power consumption and leakage. Its fast switching action is useful for multiplexing analog measurement channels, while its low on-resistance helps preserve signal integrity when the source impedance is low. Exact off-leakage, channel capacitance, charge injection, and temperature limits should be confirmed in the manufacturer data sheet before finalizing a high-impedance or precision acquisition design. Typical uses include portable data loggers, battery-powered test instruments, industrial process-control modules, military electronics, sample-and-hold systems, and general analog signal routing. For designs requiring higher current or lower resistance, the switch rating must remain within the load and signal-integrity limits of the complete analog path. When laying out the PCB, place the DG417DJ close to the signal source and destination to minimize parasitic capacitance and resistance. Keep the analog and digital return paths disciplined, provide stable supply decoupling, and verify the control-pin logic levels. Reviewing the DG417 data sheet pin description and timing diagrams is essential when new switches are added to an existing board.
DG417DY+ - 35 Ohm SPST Analog Switch | Maxim Integrated
The Maxim Integrated DG417DY+ is a precision CMOS monolithic analog switch with one normally closed SPST channel, 35 ohm maximum on-resistance, and an 8-SOIC package. The verified distributor listing identifies a 1:1 switch configuration and 8-SOIC package, while the manufacturer page places the DG417 family in production and describes improved precision switching. A manufacturer-listed starting price is $3.56 for 1,000 units, making the part suitable for signal-routing designs that need low leakage, controlled charge injection, and bidirectional conduction. An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The DG417 belongs to the broader interface-IC hierarchy: analog switch, CMOS analog switch, SPST switch, and signal-routing component. Its normally closed configuration means the selected signal path is conductive in the default power-down state, while the control input determines the switching state. This topology is useful when continuity must be maintained unless a separate control signal actively interrupts the path. Verified family-level features include maximum on-resistance of 35 ohms, on-resistance matching up to 3 ohms between switches, on-resistance flatness up to 4 ohms over the signal range, charge injection up to 10 pC, off leakage below 5 nA at +85 degrees Celsius, and ESD withstand of at least 2000 V per Method 3015.7. The device also offers low power consumption and is designed to conduct equally well in either signal direction. The DG417 family is specified for precision analog routing rather than high-voltage power switching. Its CMOS construction supports low leakage and compact integration, while controlled charge injection helps limit transient errors when the switch changes state. Exact supply range, control-logic levels, switch timing, and channel-specific pin behavior are not present in the supplied excerpts and are therefore not inferred here. Typical uses include analog signal conditioning, test-equipment routing, instrumentation, communications equipment, and precision measurement paths. The switch can route a sensor, amplifier, or converter signal when system timing requires a normally closed connection. Designers should verify the complete datasheet limits for supply voltage, signal range, control thresholds, and absolute maximum ratings before finalizing a new design. For PCB implementation, place the device close to the routed signal so trace capacitance and resistance remain low. Keep sensitive analog traces away from fast digital control lines, provide a stable ground reference, and account for injected charge at downstream amplifiers or sampling circuits. The 8-SOIC package is a surface-mount package suitable for conventional PCB assembly and hand or automated placement. This page combines the verified manufacturer overview, distributor identification, and public comparison data with engineering guidance focused on signal integrity, switching behavior, and design validation. It intentionally distinguishes verified facts from parameters that require confirmation in the complete manufacturer datasheet.
DG418AK - 35Ω SPST CMOS Analog Switch | Vishay
The Vishay DG418AK is a single-channel, single-pole single-throw CMOS analog switch with a 35 ohm on-resistance, housed in an 8-pin CERDIP package. It supports a -15 V to +15 V supply-voltage range and is specified for operation from -55°C to +125°C. The DG418AK is designed for precision analog-signal routing where low leakage, repeatable switching, and a stable low on-resistance are important. An analog switch is an integrated semiconductor device that routes an electrical signal between circuit nodes under digital control. The DG418AK belongs to the analog-switch hierarchy, where its SPST configuration provides one independently controlled connection path. Unlike a mechanical relay, it changes state electronically and can operate within systems that require compact signal-routing devices with CMOS-compatible control logic. The switch features a nominal 35 ohm on-resistance and switching times of 175 ns for turn-on and 145 ns for turn-off. It is specified for a 15 V analog-signal range and uses TTL- and CMOS-compatible control signals. The -55°C to +125°C temperature range makes the part suitable for industrial, instrumentation, communications, and temperature-extended signal-conditioning equipment when the complete circuit meets its environmental requirements. Internally, the DG418AK is a precision monolithic CMOS analog switch designed to minimize resistance variation across the operating signal range. The DG418 family is associated with guaranteed on-resistance matching and flatness characteristics, which help preserve amplitude accuracy when signals pass through the switch. Its bidirectional signal path supports use in input selection, output isolation, test-signal routing, and sampled measurement systems. Typical applications include precision test and measurement systems, data-acquisition front ends, analog signal multiplexing, sensor conditioning, communications equipment, and industrial control modules. A designer can use the DG418AK when a single SPST path is sufficient and the signal amplitude remains within the supported range. The 175 ns turn-on time and 145 ns turn-off time are suitable for moderate-speed routing rather than very high-frequency applications. For layout, keep analog traces short and provide a low-impedance return path to minimize coupling from adjacent digital or switching circuits. Confirm the logic levels against the device control-input thresholds, review leakage across the full temperature range, and ensure the switched signal remains within the stated analog-signal range. The manufacturer datasheet pin description should be used directly when assigning PCB connections. This page combines the exact DG418AK device characteristics, commercial sourcing guidance, related precision-switch options, and practical design considerations. It helps engineers evaluate the DG418AK for high-temperature and precision-routing designs while distinguishing verified drop-in candidates from alternatives that require a different package or PCB footprint.
DG418CJ+ - 35 Ohm SPST Analog Switch | Analog Devices
Analog Devices DG418CJ+ is a precision CMOS analog switch with a 35 ohm maximum on-resistance, configured as a single SPST circuit in an 8-pin PDIP package. The normally open architecture provides a high-impedance off state between the switched terminals, making the device useful when signal routing, isolation, sampling, and test-fixture control are required. The manufacturer identifies the DG418 family as a production product designed for improved switching consistency and low leakage over temperature. An analog switch is an interface integrated circuit that connects or disconnects an analog signal path under digital control. Within the semiconductor hierarchy, the DG418CJ+ is an analog switch, a member of the multiplexer and demultiplexer family, and an interface IC used between sensors, measurement circuits, converters, and digital control logic. Unlike a mechanical relay, it can switch without moving physical contacts and can therefore support compact, repeatable signal control. Key characteristics include a maximum on-resistance of 35 ohms, SPST switching, normally open operation, and an 8-pin PDIP package. The on-resistance specification is important because series resistance can produce signal attenuation and voltage-dependent error in divider networks. The normally open state also provides a useful default: the switched path remains disconnected until the control input asserts the switch. Additional electrical and environmental details should be taken from the DG418 manufacturer datasheet before finalizing a precision signal-chain design. The DG418 family uses CMOS circuitry to control analog signal paths while keeping the controlled terminals electrically distinct from the logic interface. In the 1:1 configuration identified for DG418CJ+, the switch is suited to routing one signal path between circuit sections or providing isolation during measurement. Its logic levels and switching timing determine how directly it can be connected to a controller, so input thresholds, supply requirements, and allowable control-state combinations must be checked against the datasheet. Typical applications include precision test and measurement systems, sensor isolation paths, battery-powered instrumentation, analog signal routing, and sample-and-hold or data-acquisition front ends. The 8-pin PDIP format is particularly useful for prototype boards, educational equipment, and legacy industrial designs that use through-hole DIP sockets rather than high-density surface-mount packages. The package also simplifies socketed replacement and hand soldering during engineering validation. Designers should treat the 35 ohm maximum on-resistance as a signal-integrity constraint. Place the switch close to the protected or routed node, provide a defined return path, and evaluate the resulting attenuation against the source impedance and downstream amplifier input. State-dependent logic behavior, power rails, and unused control terminals should be validated using the manufacturer's pin-description and application guidance rather than inferred from the family name. This product page organizes the DG418CJ+ electrical facts, package information, drop-in candidates, and practical selection guidance into one engineering reference. It also distinguishes directly compatible replacements from broader functional similarities, helping PCB designers preserve pin and footprint continuity while accounting for temperature-grade, switching-state, and application-specific requirements.
DG418CY+ - 35Ω SPST CMOS Analog Switch | Maxim
The Maxim Integrated DG418CY+ is a precision, CMOS, monolithic SPST analog switch with one normally open channel, a maximum on-resistance of 35 Ω, and an 8-pin SOIC package. It is designed to route analog signals while providing guaranteed on-resistance matching of 3 Ω maximum between switches and on-resistance flatness of 4 Ω maximum across the signal range. An analog switch is a semiconductor-controlled routing component that connects or disconnects analog signals under digital control. The DG418 belongs to the broader analog-switch and multiplexer hierarchy, where it belongs to the interface-IC and signal-routing category. Unlike a mechanical relay, it operates without moving contacts and is therefore suitable for compact instrumentation, data-acquisition, industrial-control, and test-equipment systems. Key electrical features include a low on-resistance, low charge injection of 10 pC maximum, and off-leakage current below 5 nA at +85 °C. These characteristics reduce signal-distortion and settling effects in precision circuits. The switch conducts equally well in either signal direction and includes ESD protection of 2000 V minimum according to Method 3015.7. Its low power consumption also makes it suitable for systems where supply current is constrained. The DG418CY+ uses precision CMOS circuitry to provide a consistent resistance when the switch closes. On-resistance matching limits channel-to-channel variation in designs that use multiple switches, while flatness describes how little the on-resistance changes across the usable signal range. These two properties help preserve amplitude accuracy and simplify calibration when the device is used in measurement front ends or signal-routing matrices. Typical applications include data acquisition, instrumentation, industrial control, sample-and-hold systems, test and measurement equipment, and general-purpose analog signal routing. In these systems, the DG418CY+ can isolate a sensor, route a test signal, or select a measurement path without introducing excessive resistance, charge injection, or off-state leakage. Designers should use the pin-description and typical application circuits in the manufacturer data sheet when assigning control inputs and signal pins. The analog signal path should remain within the device's published voltage and current limits, while the control signal should use the logic levels specified for the particular DG418 variant. PCB signal traces should be short and appropriately terminated to minimize coupling into the switched node. This product page combines the manufacturer's DG418 family documentation, package and circuit details, procurement facts, replacement analysis, and practical design guidance. It also distinguishes exact drop-in interchangeability from devices that merely use the same package or offer related switching functions.
DG418DJ+ - 35Ω SPST Analog Switch | Analog Devices
Analog Devices DG418DJ+ is a precision CMOS analog switch with a 35 Ω maximum on-resistance, 100 ns switching action, and a normally open SPST configuration in an 8-pin PDIP package. It supports analog signals up to 15 V, accepts a maximum supply voltage of 44 V, and is compatible with TTL and CMOS control logic. The device is intended for applications requiring fast, low-power signal routing. An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. Unlike a mechanical relay, it has no moving contacts and can switch rapidly with low power consumption. In the power-management hierarchy, the DG418DJ+ belongs to the interface-IC category, where analog switches connect precision measurement, communication, audio, and instrumentation circuits to shared signal paths. The principal features include a 35 Ω on-resistance, 100 ns turn-on action, and 35 nW power dissipation. A 15 V analog signal range provides compatibility with conventional bipolar and CMOS signal systems, while the 44 V maximum supply rating provides additional operating margin. TTL compatibility allows the switch to be driven by common digital logic levels without an additional level-conversion stage. Internally, the DG418DJ+ uses CMOS circuitry to control the analog path. Its low power requirement makes it appropriate for continuously connected signal-routing systems where relay-style control current would be excessive. Fast switching action also allows the device to respond quickly to digital selection signals, although delay, bandwidth, charge injection, and off-isolation characteristics must be considered when designing around the switching edges. Typical uses include multimeter and oscilloscope input routing, test and measurement systems, sample-and-hold systems, battery-powered instrumentation, analog signal multiplexing, and industrial control interfaces. The normally open configuration is particularly useful when a signal path must remain disconnected until the control input activates it. For layout, keep routing from the control pin and analog terminals short, and maintain a common ground reference between the switch and the connected circuit. Check the supply input, control thresholds, signal range, and off-state isolation in the manufacturer datasheet before finalizing a design. The through-hole PDIP package also requires adequate spacing for lead insertion and soldering.
DG418DY+ - 35 Ohm Precision CMOS Analog Switch | Analog Devices
The Analog Devices DG418DY+ is a single-channel precision CMOS analog switch configured as a 1:1 SPST normally open switch, with an on-resistance of 35 ohms in an 8-pin SOIC package. It supports a 12 V single-supply configuration and belongs to the DG417, DG418, and DG419 precision analog-switch family. An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The DG418DY+ combines low power, low leakage, high switching speed, and low on-resistance in a compact surface-mount package. In this switching role, the 1:1 configuration provides one signal path for signal-routing, test, measurement, and control systems. Key features include a typical on-resistance of 35 ohms, maximum on-resistance matching of 3 ohms between switches, and maximum on-resistance flatness of 4 ohms across the signal range. These characteristics help limit resistance variation when a switched signal changes amplitude. The device is manufactured in an 8-SOIC package for compact surface-mount PCB layouts. The DG418DY+ is part of Maxim Integrated's redesigned precision CMOS monolithic analog-switch family. Its low-leakage behavior is suitable for circuits where the off-state contribution to system error must remain small. The 35-ohm on resistance also makes the switch appropriate for general-purpose low- and moderate-impedance analog signals rather than applications requiring near-zero resistance. Typical uses include battery-powered instrumentation, industrial control systems, data-acquisition equipment, test and measurement setups, and portable or military electronic systems. The 8-pin SOIC package supports conventional surface-mount assembly, while the low power and leakage characteristics suit systems where standby current and signal integrity affect overall performance. When designing around the DG418DY+, verify the control logic, supply arrangement, input signal range, and external pull-up or pull-down requirements against the manufacturer pin description and application guidance. The switching node should also be kept away from fast digital return paths to reduce coupling into the analog signal path. This product page combines the manufacturer specifications, drop-in replacement research, a package and pinout reference, and practical engineering guidance to support component selection and PCB implementation.
DG418LDJ+ - 35 Ohm SPST Analog Switch | Analog Devices
The Analog Devices DG418LDJ+ is a single-channel, normally open SPST CMOS analog switch with 35 ohm on resistance, 3 V logic compatibility, and an 8-pin PDIP package. It supports dual supply voltages from ±4.5 V to ±20 V and is intended for precision signal-routing applications requiring low control logic compatibility and fast switching performance. An analog switch is a semiconductor device that connects or isolates circuit nodes under digital control. The DG418LDJ+ belongs to the analog switch and multiplexer hierarchy, where it provides one independently controlled SPST path. Unlike a mechanical relay, the CMOS implementation switches without moving contacts, making it suitable for test systems, instrumentation, data acquisition, communications, and industrial control equipment where repetitive operation, compact size, and controlled switching behavior are important. The device provides a 1:1, one-circuit configuration with a maximum on resistance of 35 ohm. Its normally open SPST topology keeps the switched path disconnected until the control input activates it. A 3 V logic-compatible control interface allows the switch to be operated by modern low-voltage digital logic, while the ±4.5 V to ±20 V analog supply range supports both dual-rail and bipolar signal environments. The listed maximum switching turn-off time is 185 ns. Internally, the DG418LDJ+ uses CMOS circuitry to control the analog conduction path while separating the control input from the switched terminals. This architecture supports fast operation and low off-state leakage, although the exact leakage, bandwidth, charge injection, and channel capacitance values must be confirmed in the manufacturer datasheet before final signal-integrity calculations. The 8-pin PDIP package also provides generous lead spacing for breadboard, through-hole prototype, and manually assembled industrial applications. Typical uses include precision test-and-measurement systems, sensor signal switching, sample-and-hold subsystems, battery-powered acquisition equipment, and communication interface routing. The normally open behavior is useful when a default isolation state is preferred, while the dual-supply range supports bipolar waveforms commonly encountered in instrumentation and industrial control systems. PCB layout should keep the analog signal path short and place decoupling capacitors close to the supply pins. Confirm logic thresholds, signal swing, bandwidth, leakage, and switch capacitance against the application before release, especially when switching low-amplitude or high-impedance signals where charge injection and off-state leakage can affect measurement accuracy. This page consolidates the component configuration, electrical limits, package details, comparison data, and practical replacement guidance for engineers evaluating the DG418LDJ+. It also distinguishes verified drop-in options from broader functional equivalents, helping simplify sourcing and board-level design decisions.
DG419AK - 35Ω SPDT CMOS Analog Switch | Vishay Siliconix
The Vishay Siliconix DG419AK is a single-circuit, 2:1 SPDT CMOS analog switch with a listed on-resistance of 35 Ω, supplied in an 8-pin CERDIP package. It is designed to route analog signals by connecting one common terminal to either of two independent input terminals. The DG419 family provides low power consumption, low charge injection, low on-resistance matching, and a flat on-resistance characteristic across the analog signal range. An analog switch is an integrated semiconductor device that controls the path of voltage or current signals without mechanically moving a contact. The DG419AK belongs to the interface-IC hierarchy, where CMOS analog switches connect sensors, amplifiers, converters, test circuits, and other signal-processing blocks. Its SPDT configuration makes it useful where one signal path must be selected from two sources, including test and measurement, data acquisition, and industrial control systems. The manufacturer describes the DG419 family's redesigned precision switches as having guaranteed on-resistance matching of 3 Ω maximum between switches and guaranteed on-resistance flatness of 4 Ω maximum over the signal range. These characteristics help reduce channel-dependent gain errors when the same switch is used for multiple paths. The DG419AK listing also identifies a 35 Ω on-resistance, while another catalog record for the DG419AK lists 30 Ω. The monolithic CMOS construction supports bidirectional signal conduction and low power consumption. The DG419 family is also described as providing low charge injection, which is important when switching signals into sampling capacitors. Manufacturer documentation states a minimum ESD tolerance of 2000 V per Method 3015.7. These characteristics make the switch suitable for precision analog routing where insertion resistance, switching transients, leakage, and signal integrity affect overall measurement accuracy. Typical applications include multimeter and oscilloscope input routing, automated test-equipment signal paths, sensor-selection networks, sample-and-hold front ends, and industrial measurement systems. In these systems, the switch can reduce the number of external relays and reduce the number of amplifiers, while providing consistent analog paths across multiple channels. The common package also supports legacy instrument and test-system designs that use 8-pin ceramic DIP footprints. Designers should verify supply-voltage limits, signal-range limits, switching-time requirements, leakage, charge injection, and control-logic thresholds against the manufacturer datasheet before production. Pay particular attention to break-before-make behavior, off-state isolation, and the external clock or control signal used to change the selected path. Prototype layouts should preserve the footprint and pin assignment of the original ceramic DIP design when evaluating a replacement. This page organizes the DG419AK technical characteristics, sourcing information, comparison criteria, and practical design guidance. It also distinguishes the confirmed 8-CERDIP replacement path from electrically similar parts offered in other packages, helping engineers evaluate PCB compatibility before making a drop-in substitution.
DG419CJ+ - 35Ω SPDT CMOS Analog Switch | Analog Devices
Analog Devices DG419CJ+ is a precision, 1-channel CMOS SPDT analog switch with a maximum on-resistance of 35 Ω, on-resistance matching of 3 Ω maximum, and on-resistance flatness of 4 Ω maximum. The device is packaged in an 8-pin through-hole DIP package and supports dual supply configurations of ±10 V to ±30 V or ±4.5 V to ±20 V. It is designed for precision signal-routing applications requiring low and repeatable insertion resistance. An SPDT analog switch is a semiconductor device that connects one common terminal to one of two switched terminals. In the broader component hierarchy, the DG419CJ+ belongs to the analog switch, analog multiplexer, interface IC, and semiconductor categories. This topology allows a signal source to be routed to either destination, or alternately connects two external nodes, making it useful for test systems, measurement equipment, signal routing, and precision analog systems. Key characteristics include matching between the two switch paths to within 3 Ω maximum and flatness across the signal range to within 4 Ω maximum. These parameters help minimize path-dependent gain error and distortion when the same signal is routed through either side of the switch. The monolithic CMOS construction supports equal signal conduction in either direction and provides a compact interface IC solution for bipolar and split-supply analog circuits. The DG419CJ+ offers a practical 35 Ω maximum on-resistance for precision, rather than ultra-low-impedance, routing. Its 8-pin DIP package accepts a 0.300-inch, 7.62 mm body width and facilitates through-hole assembly, prototyping, and socket-based laboratory use. The switch operates with positive and negative analog supplies, allowing bipolar signals to pass without single-ended signal-path restrictions. Typical uses include precision test and measurement systems, sample-and-hold front ends, signal-routing matrices, laboratory equipment, and industrial control modules. The matched paths are especially useful when calibration or measurement results must remain consistent regardless of which switched terminal is selected. It is also suitable for designs that route low-frequency analog signals rather than high-speed RF or ultrafast data lines. Designers should evaluate the 35 Ω on-resistance against the source and load impedance. A high-impedance receiving circuit will reduce the impact of that resistance, while a low-impedance load may require an amplifier or a lower-resistance switch. Also verify control-pin levels, supply sequencing, and unused-pin handling against the Analog Devices DG419 data sheet before finalizing the layout. This product page combines the manufacturer’s core electrical characteristics with application-specific design guidance, package information, comparison criteria, and practical selection guidance. It is intended to help engineers determine whether the DG419CJ+ offers the required switch topology, resistance behavior, supply range, and through-hole footprint before beginning a board design.
DG419CY+ - 35Ω SPDT Analog Switch | Analog Devices
The Analog Devices DG419CY+ is a precision CMOS monolithic SPDT analog switch with 35Ω maximum on-resistance, one switch circuit, and an 8-SOIC package. The device operates from 10V to 30V as an analog switch and supports ±4.5V to ±20V dual-supply operation. According to the manufacturer product page, the DG419 family provides guaranteed on-resistance matching of 3Ω maximum and on-resistance flatness of 4Ω maximum across the signal range. An analog switch is an integrated semiconductor that routes an electrical signal between terminals under digital control. An SPDT switch has one common terminal and two switched terminals, making it useful for signal selection, routing, and multiplexing. Within the interface-IC hierarchy, this device belongs to the analog switch and multiplexer class rather than a digital logic or power-management component. The DG419CY+ is designed for balanced low-power consumption and low signal errors. Maxim's DG417, DG418, and DG419 family is specified to conduct equally well in either direction, with low charge injection, low power dissipation, and a minimum ESD tolerance of 2000V. These characteristics make the switch appropriate where controlled routing of precision or low-level signals is required. Electrical operation covers a 10V to 30V analog signal range and supply configurations of ±4.5V to ±20V. The 35Ω maximum on-resistance specification defines the worst-case signal-path resistance, while the 3Ω maximum matching specification limits difference between switch paths. Matching is particularly useful in differential or balanced systems where unequal path resistance could create gain errors or channel mismatch. Typical uses include precision test and measurement equipment, guidance and control systems, analog signal multiplexing, instrumentation interfaces, and communication routing. The 8-SOIC surface-mount package supports compact layouts while retaining conventional small-outline lead spacing. Designers should verify supply limits, signal swing, leakage, switching timing, and operating-temperature requirements against the exact production data before finalizing a high-reliability design. A key implementation consideration is to identify the common and switched pins correctly and account for the 35Ω insertion loss when calculating downstream signal attenuation. The switch also adds capacitance and charge injection, which can affect timing-sensitive or high-impedance nodes. This page combines verified distributor information, manufacturer documentation, drop-in alternatives, and practical selection guidance to support an informed design decision.
DG419DJ+ - 35Ω Precision SPDT CMOS Switch | Analog Devices
Analog Devices DG419DJ+ is a precision, monolithic CMOS SPDT analog switch with one 2:1 switch circuit, a 35 Ω on-resistance rating, and an 8-pin PDIP package. The device uses low charge injection and low power consumption to route analog signals with minimal disturbance. According to the Analog Devices product page, the redesigned DG417, DG418, and DG419 family guarantees on-resistance matching of 3 Ω maximum between switches and on-resistance flatness of 4 Ω maximum over the signal range. An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. The SPDT topology provides one common terminal and two switched terminals, making the DG419DJ+ useful for signal selection, polarity routing, test-point isolation, and channel multiplexing. In the broader hierarchy, it is an analog switch, an interface IC, and a discrete signal-routing function that complements power management, data converters, and communication components. Key benefits include a maximum on-resistance of 35 Ω, bidirectional signal conduction, low charge injection, low power consumption, and ESD tolerance of at least 2000 V per Method 3015.7. The 44 V maximum supply rating gives the device useful headroom for dual-supply analog systems, while the VSS-to-VDD analog signal range supports switching across positive and negative rails. The package is an 8-pin PDIP, allowing conventional through-hole assembly rather than requiring a fine-pitch surface-mount footprint. The DG419DJ+ is built around a monolithic CMOS analog-switch architecture. Its two throws provide complementary routing paths, while the control input determines which terminal is connected to the common node. Matching between the switched paths is important in precision systems because unequal resistance can create gain or attenuation differences after the signal changes direction. The family’s specified 3 Ω maximum matching therefore helps preserve channel consistency. Typical uses include precision signal-path routing in test and measurement equipment, analog front-end channel selection, instrumentation multiplexing, and bipolar analog-signal switching. In a measurement circuit, the common terminal can be connected to either sensor or reference path. In a test system, it can isolate a device-under-test input while keeping the external node disconnected from the source. Designers should account for the 35 Ω on-resistance when calculating signal attenuation, and should verify charge injection against the accuracy required by the selected amplifier or converter. Supply bypassing and control-signal timing also require attention because the CMOS switch and surrounding analog circuitry must remain stable across the intended signal and common-mode ranges. This page consolidates the verified manufacturer information, distributor availability data, package details, parameter comparisons, and practical switching considerations. It also separates confirmed DG419 family characteristics from parameters that were not available in the supplied source data, helping engineers evaluate the DG419DJ+ without relying on unverified specifications.
DG419DY+ - 35Ω Precision CMOS SPDT Switch | Analog Devices
The Analog Devices DG419DY+ is a single-channel precision CMOS analog switch in an 8-SOIC package, configured as one SPDT or 2:1 multiplexer. Its headline ratings include a maximum on-resistance of 35 Ω, guaranteed on-resistance matching of 3 Ω maximum between switches, and on-resistance flatness of 4 Ω maximum over the signal range. The monolithic switch supports analog signal ranges from 10 V to 30 V and supply operation from 4.5 V to 20 V. An analog switch is an electronic routing component that connects or disconnects signal paths under digital control. The SPDT architecture transfers one common terminal between two switched terminals, making it suitable for signal selection, polarity routing, test-point isolation, and bidirectional signal-path control. As a precision CMOS switch, the DG419DY+ belongs to the interface IC and analog switch hierarchy while adding low power consumption and bidirectional operation. The DG419 family combines matched on-resistance, flat on-resistance behavior, low charge injection, and low power consumption. Maximum on-resistance matching of 3 Ω supports applications where closely matched paths reduce gain or timing errors. The specified on-resistance flatness of 4 Ω limits resistance variation as the analog voltage changes, which is valuable in precision measurement and signal-conditioning systems. The improved DG419 design also provides an ESD tolerance of 2000 V minimum under Method 3015.7. The switch operates bidirectionally, allowing signals to flow through the selected path in either direction. Its CMOS implementation supports low power dissipation without requiring a normally closed mechanical contactor. Charge injection can create transient errors when the control state changes, so systems using the switch for sampling or high-impedance measurements should account for control timing, source impedance, and downstream capacitance. Typical applications include precision test equipment, guidance and control systems, battery-powered instruments, data-acquisition front ends, and switching networks for low-frequency analog signals. The DG419DY+ is particularly appropriate when a compact 8-SOIC footprint, matched resistance, and low-noise switching are more important than the very low capacitance of specialized RF switch products. Use the manufacturer pin-description table when assigning PCB tracks and confirm the control polarity and terminal arrangement for the exact DG419DY+ orderable device. Keep the switched signal within the stated analog and supply ratings, provide a stable control reference, and account for charge injection when the switch changes state. This product page combines the DG419DY+ datasheet specifications, verified manufacturer and distributor sources, compatible replacement candidates, and application-oriented engineering guidance. It also distinguishes direct footprint alternatives from functional substitutes so engineers can assess drop-in replacement risk before modifying an existing analog switching circuit.
DG419DY-T1-E3 - Precision CMOS SPDT Analog Switch | Vishay
The Vishay Siliconix DG419DY-T1-E3 is a single-pole double-throw (SPDT) precision monolithic CMOS analog switch that combines low power consumption with high switching speed and excellent signal integrity. Housed in an 8-pin SOIC (NSOIC) package, the part provides a single 2:1 switch channel with a typical on-resistance of 35 ohms, supporting analog signal rails up to ±15 V or 30 V single supply. The DG419DY-T1-E3 is supplied on a 3000-piece tape-and-reel carrier and targets precision signal routing in industrial, instrumentation, and battery-powered systems. An analog switch (also called a CMOS switch or bilateral switch) is an active semiconductor device that uses MOSFET transistors to pass or block analog signals. It belongs to the broader hierarchy of interface ICs -> analog switches/multiplexers -> signal conditioning -> data acquisition. Unlike electromechanical relays, CMOS analog switches offer nanosecond switching, low power draw, no contact bounce, and zero off-state current leakage when fully turned off, making them ideal for solid-state signal multiplexing in modern mixed-signal designs. Key features of the DG419DY-T1-E3 include a typical on-resistance of 35 ohms, low charge injection, break-before-make switching action, and TTL/CMOS-compatible digital logic inputs. The device operates from a single 10 V to 30 V supply or from dual ±5 V to ±15 V supplies, with a logic threshold that allows direct interface to 3.3 V or 5 V microcontrollers. Its low power consumption (under 35 mW quiescent) and rugged ESD protection make it suitable for both portable and line-powered designs. The DG419DY-T1-E3 uses a precision CMOS architecture with on-resistance matching between channels and flat on-resistance across the analog signal range, minimizing total harmonic distortion when passing audio or precision DC signals. The break-before-make switching topology prevents momentary shorts between input sources during channel transitions, which protects upstream drivers and downstream ADCs from current spikes. Typical applications include precision test equipment, guidance and control systems, battery-powered instrumentation, data acquisition front-ends, audio signal routing, sample-and-hold circuits, and programmable gain amplifiers. The wide operating voltage range and high off-isolation make it equally suitable for industrial 4-20 mA signal routing and for low-voltage sensor multiplexing. When designing with the DG419DY-T1-E3, observe the absolute maximum supply voltage of 44 V to avoid permanent damage. Place 0.1 µF decoupling capacitors close to V+ and V- pins, and ensure the logic input does not exceed V+ or fall below ground. For high-impedance source signals, add a small series resistor at the output to limit capacitive kickback during switching transitions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers select the right CMOS switch and validate its drop-in compatibility against the most popular Vishay, Maxim Integrated, and Texas Instruments equivalents.
DG419LDJ+ - 35 Ohm SPDT Analog Switch | Analog Devices
The Analog Devices DG419LDJ+ is a single-channel SPDT CMOS analog switch with 35 ohm maximum on-resistance, +3 V logic compatibility, and an 8-pin PDIP package. It supports dual-supply operation from ±4.5 V to ±20 V and an extended operating temperature range of -40°C to +85°C. The switch is designed for low-voltage, low-power signal-routing applications where one source must connect to one of two destinations. An analog switch is an interface IC that connects or isolates an analog signal under digital control. A SPDT switch can route one common terminal to either of two independent terminals, making it useful for signal selection, polarity routing, test-point isolation, and signal-path multiplexing. The DG419LDJ+ belongs to the Analog Devices DG419L precision analog-switch family, combining low on-resistance with improved matching, flat on-resistance, low charge injection, and low off-leakage. Key features include a maximum on-resistance of 35 ohms, on-resistance matching within 3 ohms, and flat on-resistance variation limited to 4 ohms across the signal range. Charge injection is limited to 10 pC, while off-leakage remains below 5 nA at +85°C. The logic-compatible control architecture allows +3 V control operation when the device is powered from ±12 V or ±15 V supplies, simplifying interfacing with modern control logic. The DG419LDJ+ uses a low-power CMOS analog-switch architecture to support signal routing without adding substantial dynamic power. Its improved matching between channels and guaranteed flat on-resistance make it appropriate where consistent insertion loss matters across the selected signal range. The 185 ns maximum off-time supports applications requiring rapid transition between routed states. Typical uses include audio signal routing, battery-operated equipment, communication systems, guidance and control circuits, military radios, modems, and PBX or PABX equipment. The device is particularly useful where a ±4.5 V minimum dual supply is acceptable and a through-hole PDIP package simplifies inspection, prototyping, and serviceability. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks. Keep the common and switched terminals away from long parallel routes carrying fast signals, connect supply decoupling close to the appropriate pins, and verify the control voltage against the selected supply configuration before powering the device. This page consolidates manufacturer specifications, sourcing guidance, application fit, and practical design notes for engineers evaluating the DG419LDJ+. It also distinguishes true package-compatible alternatives from related surface-mount versions that require a different PCB footprint.
DG421CJ - Dual SPST Analog Switch | Analog Devices
The Analog Devices DG421CJ is a low-power CMOS analog switch containing two independently controlled SPST-NO switches, each with a maximum on-resistance of 35 ohms. The device is packaged in a 16-pin through-hole DIP and is specified for dual 15 V supply operation. Its latched control inputs support retained switch state and are suited to analog signal routing, instrumentation, test equipment, and industrial control systems. An analog switch is a semiconductor device that connects or isolates signal paths under digital control. The DG421CJ belongs to the analog switch hierarchy within multiplexers and interface ICs. Unlike a mechanical relay, it offers compact size, low switching power, and fast electronic control. Its normally open configuration provides a defined open state when a control input is deasserted, while the paired switches can route two independent channels or provide isolation between source and measurement circuitry. Key features include guaranteed on-resistance matching of 3 ohms maximum between switches and on-resistance flatness of 4 ohms maximum over the signal range. Typical on-resistance is 20 ohms, and the low-power CMOS design is intended to minimize power consumption in multi-switch systems. The 16-PDIP package uses a 0.300-inch, 7.62 mm body width and supports conventional through-hole PCB assembly rather than surface-mount reflow. The switch architecture provides independent control paths for two SPST-NO channels. Guaranteed matching between the two switches is useful when both devices must present similar resistance to sampled signals. Flatness limits resistance variation across the selected signal range, helping preserve measurement consistency when the source voltage changes. Low-power CMOS operation also makes the device appropriate for portable test and measurement systems where supply efficiency and predictable signal behavior are important. Typical uses include battery-powered instrumentation, automated test equipment, analog measurement front ends, sample-and-hold isolation networks, and industrial interface modules. The two channels can be used for measurement-source selection, signal isolation, or alternating access to two external circuits. In systems with higher voltage levels, designers must confirm the complete absolute-maximum and signal-range limits in the manufacturer datasheet before applying the switches outside the intended dual-supply domain. For PCB layout, place the device so its through-hole leads do not cross sensitive analog traces, and route switched signals away from clocks, relay drivers, and switching power converters. Use a common ground reference for control and analog circuitry. Because this legacy part is obsolete, production replacements should be qualified for pin compatibility, supply voltage, on-resistance, leakage current, switching speed, and temperature range rather than selected by package name alone. This product page organizes the DG421CJ technical characteristics, sourcing information, application guidance, and drop-in replacement assessment. It also distinguishes verified device capabilities from engineering checks that should be completed before approving any substitute in an existing analog signal path.
DG421DJ - Low-Power Latched SPST CMOS Switch | Maxim
The Maxim Integrated DG421DJ is a low-power CMOS analog switch with latch, configured as a dual SPST switch and supplied in a 16-pin DIP package. Its headline characteristics include a typical on-resistance of 20 ohms, guaranteed on-resistance matching of 3 ohms maximum between switches, and guaranteed on-resistance flatness of 4 ohms maximum across the signal range. The device is intended for industrial-grade applications requiring low-power signal routing with controlled channel resistance. An analog switch is a semiconductor device that connects or disconnects an electrical signal path under digital control. The DG421 belongs to the analog-switch hierarchy within interface ICs and broader signal-management semiconductors. Unlike a mechanical relay, a CMOS analog switch operates without moving contacts, enabling compact circuitry, low power consumption, and electronic control. Its latch feature allows the switching state to be retained, which is useful when downstream circuitry must retain a selected connection without continuous control-signal activity. The redesigned DG421 series provides guaranteed matching between the two switches and controlled on-resistance flatness over the signal range. These characteristics are important in instrumentation, data acquisition, test equipment, and control systems where different switch paths should present similar resistance. The 20-ohm typical on resistance can support moderate-voltage, low-frequency signal routing, although the supplied data does not include the complete voltage, current, bandwidth, capacitance, leakage, and logic-level limits. The DG421DJ uses a 16-pin DIP package and is identified as an industrial-temperature-grade, through-hole device. Its 16 terminals accommodate two independently controlled SPST channels, latch-related control connections, power rails, and associated pins. The verified source material confirms a 16-pin DIP package and SPST configuration, but it does not provide a complete public pin-number table. The pinout is therefore left unpopulated rather than assigning terminal functions without direct evidence. Typical uses include multiplexed sensor acquisition, programmable test fixtures, analog signal routing, sample-and-hold systems, and industrial control equipment. In each case, the guaranteed 3-ohm maximum matching and 4-ohm maximum flatness help limit channel-to-channel errors. The DG421DJ is also suitable where a latched switch state simplifies control logic, although engineers should verify the exact electrical limits from the complete manufacturer datasheet before finalizing signal levels, clocking arrangements, and operating conditions. This page consolidates the verified package, configuration, resistance, and sourcing information into an engineer-focused comparison and selection guide. It also distinguishes the DIP-16 DG421DJ from related suffix variants and emphasizes that a true drop-in replacement requires verified pin compatibility, not merely a similar function or shared package family.
DG421DY+ - Dual Latching SPST Switch | Maxim Integrated
The Maxim Integrated DG421DY+ is a two-circuit, 1:1 CMOS analog switch with latching control in a 16-pin SOP package. Its principal electrical ratings include a maximum on-resistance of 35 ohms, guaranteed on-resistance matching of 3 ohms maximum between switches, and on-resistance flatness of 4 ohms maximum over the signal range. The device is intended for industrial-temperature signal-routing systems where two independently controlled SPST paths must occupy one compact package. An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. The DG421DY+ belongs to the analog switch hierarchy, where a CMOS switch is an interface IC used for multiplexing, sampling, test, and signal routing. Its latching control preserves the commanded switch state, making it useful when system logic must remain stable during power-management transitions or when control lines are shared with other bus circuitry. The two-circuit configuration provides separate 1:1 signal paths rather than a multiplexer arrangement. Guaranteed matching between the two switches limits channel-to-channel variation in on-resistance, while the 4-ohm maximum flatness specification limits resistance changes across the signal range. These characteristics are relevant when attenuation, insertion loss, or signal integrity must remain reasonably consistent between selected channels. The DG421DY+ is manufactured as a low-power CMOS analog switch using Maxim Integrated's monolithic switch design. Latch-based operation separates the stored control state from the immediate logic level applied to the device. As a result, a control input can be pulsed without unintentionally changing the routing state after the command has been accepted, provided the application observes the timing and supply conditions specified in the manufacturer datasheet. Typical uses include battery-powered instrumentation, automated test equipment, analog signal multiplexing, sample-and-hold systems, and communication equipment that requires isolated SPST routing. The device can also support circuits where different sensors, amplifiers, or measurement channels must be connected selectively while keeping the routing state stable between control transactions. Designers should account for supply voltage, input-signal range, switching transients, control timing, and the effect of 35-ohm maximum on-resistance when calculating signal loss. The 16-pin SOP package requires adequate board spacing and careful routing of control and analog traces. Decoupling and grounding practices should follow the application guidance in the Maxim Integrated datasheet. This product page combines the switch configuration, resistance characteristics, package details, application guidance, and drop-in qualification information into an engineering-oriented reference for analog routing designs.