بەرهەمەکان (5,100+)

DG423DJ+ - Triple SPDT CMOS Analog Switch | Analog Devices
DG423DJ+

DG423DJ+ - Triple SPDT CMOS Analog Switch | Analog Devices

Analog Devices DG423DJ+ is a low-power CMOS analog switch with latches, three independently controlled SPDT channels, a typical on-resistance of 20 ohm, and a 16-pin through-hole DIP package. The device supports low-power operation while maintaining a maximum on-resistance matching of 3 ohm between switches and maximum on-resistance flatness of 4 ohm across the signal range. A CMOS analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The DG423DJ+ belongs to the analog switch and switch-and-multiplexer hierarchy, where it functions as a low-power signal-routing interface between sensors, measurement circuits, amplifiers, converters, and digital control logic. Its latched control interface allows the selected signal path to remain stable while reducing repeated control activity. The DG423 family provides guaranteed on-resistance matching of 3 ohm maximum and on-resistance flatness of 4 ohm maximum. These characteristics are important when several channels must present similar resistance to downstream circuitry. Maximum charge injection is 15 pC, helping limit timing disturbance when control signals change the selected path. The switch also provides ESD tolerance of 2000 V minimum under Method 3015.7. The three SPDT channels give the device useful routing flexibility for test-point selection, signal-path switching, and sampling networks. Each channel can connect one common terminal to either of two selectable terminals, allowing a compact design to implement muxing, polarity selection, or source selection. Because the DG423DJ+ is packaged in a 16-pin DIP, it is also appropriate for prototypes, educational equipment, and through-hole industrial assemblies. Typical uses include multimeter and oscilloscope input routing, automated test systems, instrumentation signal conditioning, battery-powered measurement equipment, and industrial control interfaces. Latched operation can reduce control-bus activity in systems where the selected channel must persist between updates, although the exact latch and enable behavior should be confirmed in the manufacturer datasheet before final sequencing logic is designed. For new PCB layouts, the principal trade-off is package footprint rather than switching performance: the 16-pin DIP is easy to prototype but occupies more board area than a surface-mount alternative. Confirm signal levels, supply voltage, logic thresholds, switch logic, and absolute maximum ratings against the manufacturer datasheet before connecting external signals. This page consolidates the documented electrical characteristics, practical routing applications, drop-in comparison information, and PCB implementation guidance needed to evaluate the DG423DJ+ during component selection.

RFQ پەیوەندی
DG423DY+ - Dual 35 Ohm CMOS Analog Switch | Maxim Integrated
DG423DY+

DG423DY+ - Dual 35 Ohm CMOS Analog Switch | Maxim Integrated

Maxim Integrated DG423DY+ is a dual-circuit, 1:1 CMOS analog switch with a stated on-resistance of 35 ohms in a 16-pin SOIC package. The device is identified as an improved low-power CMOS analog switch with latches, allowing the switched paths to retain their configuration without a continuing control input. The DG423DY+ provides normally open SPST switching and is intended for low-power analog signal routing where low leakage, compact packaging, and latched operation are useful. A CMOS analog switch is an interface IC that uses MOSFET-based transmission paths to connect or disconnect signals. Within the semiconductor hierarchy, an analog switch belongs to the interface IC category, where it sits between a controlling digital circuit and an external analog signal. Unlike a mechanical relay, it changes state electronically and can route low-level signals without mechanical contact wear. The latch function is especially valuable when the selected signal path must remain stable while the control inputs return to an inactive state. Key characteristics include a 35 ohm on-resistance, a 1:1 signal configuration, two switched circuits, a 16-pin SOIC package, and a rated operating voltage stated as 15 V. Published listings also identify the switch as an SPST, normally open device with a switching time of 250 ns and a leakage current of 500 pA. These figures position the DG423DY+ for precision signal isolation, sample-and-hold systems, instrumentation, and control interfaces where compactness and low off leakage are more important than very low on-resistance. The DG423 family uses CMOS construction to combine low power consumption with high input impedance. Its latch-based control architecture separates the momentary command used to change a path from the stable state that maintains connectivity. Compared with continuously driven analog switches, this architecture can simplify firmware behavior because the selected path remains active without requiring the controller to hold a command signal. The 16-SOIC footprint also supports conventional surface-mount assembly and mixed analog/digital board layouts. Typical uses include multiplexed sensor acquisition, precision measurement interfaces, sample-and-hold circuitry, automated test equipment, and low-level control-signal routing. The normally open topology provides a default disconnected condition when the device is reset or not actively commanded. In such systems, this behavior can reduce unintended signal coupling between circuit sections, although external pull resistors may still be required to establish a defined state during power-up. Layout should preserve short analog traces, place input and output paths away from fast digital clocks, and route supply and ground connections carefully to minimize switching transients coupling into sensitive signals. Because the switch adds 35 ohms in its conducting state, source impedance, capacitance, and the impedance of the receiving circuit should be evaluated together. For applications needing more channels, adjacent Maxim DG-series devices can simplify design, but function and control compatibility must be checked independently. This page organizes the DG423DY+ identity, documented electrical characteristics, practical applications, package information, and sourcing information into an engineering-focused guide. It also distinguishes verified device facts from specifications that require confirmation in the manufacturer datasheet, helping designers plan a compliant 16-SOIC analog-switch implementation without relying on generic connector or relay assumptions.

RFQ پەیوەندی
DG425CY - 16-Pin CMOS Latching Analog Switch | Analog Devices
DG425CY

DG425CY - 16-Pin CMOS Latching Analog Switch | Analog Devices

The Analog Devices DG425CY is a low-power CMOS analog switch with latches, a dual DPST configuration, and a 16-pin SOIC package. Its headline characteristics include 20 Ω typical on-resistance, guaranteed on-resistance matching up to 3 Ω, on-resistance flatness up to 4 Ω across the signal range, and charge injection limited to 15 pC maximum. The switch is intended for low-power signal-routing systems where latched control, low charge injection, and low-power operation are important. An analog switch is a semiconductor device that routes electrical signals between input and output terminals under digital control. The DG425 belongs to the broader CMOS switch and multiplexer hierarchy, where multiplexer and demultiplexer functions determine which signal paths are connected. Its integrated latch retains the control state, reducing the need for continuously maintained control signals and helping lower system power consumption. The DG425 family also supports bidirectional signal conduction, allowing the selected paths to carry signals in either direction. The redesigned DG421, DG423, and DG425 devices provide guaranteed matching and flatness, making channel behavior more predictable than an unqualified resistance specification alone. The DG425CY combines these switch characteristics with a maximum charge injection of 15 pC and an ESD tolerance of at least 2000 V per Method 3015.7. These characteristics make the device useful where switching transients, channel mismatch, or ESD exposure could affect signal integrity. The CMOS implementation supports operation from dual supplies, including a -15 V to +20 V total supply span in the cited DG425CY-T technical data. Switching timing data cited for that ordering variant includes approximately 250 ns turn-on and 200 ns turn-off. Because DG425CY is a specific package and temperature-ordering variant of the DG425 family, engineers should verify the complete ordering code, supply limits, control logic, and electrical limits against the manufacturer datasheet before production release. Typical uses include battery-powered instrumentation, test-equipment signal routing, data-acquisition systems, communication equipment, and analog measurement circuits. The latching control is particularly useful when a selected measurement path must remain connected while the host processor sleeps. The device can also serve in circuits requiring a pair of independently latched double-pole paths for source, range, or channel selection. The principal design consideration is maintaining adequate logic-level compatibility across the complete supply range. Because control thresholds can change with VDD and VSS, external logic should not be assumed to remain compatible throughout every operating condition. PCB layout should keep analog traces short, provide a stable ground reference, and place bypass capacitors close to the supply pins. Designers should also evaluate injected charge against the input impedance and acquisition bandwidth of the downstream circuit. This page consolidates the verified manufacturer and distributor information for DG425CY with package details, application guidance, lifecycle considerations, and replacement qualification notes. It is intended to help engineers distinguish a true same-footprint replacement from a related family member whose latch configuration, temperature grade, package code, or electrical limits differ.

RFQ پەیوەندی
DG425DJ - Low-Power CMOS Latched Analog Switch | Maxim Integrated
DG425DJ

DG425DJ - Low-Power CMOS Latched Analog Switch | Maxim Integrated

The Maxim Integrated DG425DJ is a low-power CMOS monolithic analog switch with latch control, supplied in a 16-pin DIP package. The device provides dual analog switching with a typical on-resistance of 20 Ω, guaranteed on-resistance matching between switches of 3 Ω maximum, and on-resistance flatness over the signal range of 4 Ω maximum. Its specified characteristics support signal-path routing in microprocessor-controlled analog and industrial systems. An analog switch is an electronic semiconductor device that routes electrical signals between circuit paths under digital control. CMOS analog switches combine low power consumption with high input impedance and bidirectional signal conduction. The DG425 family belongs to the analog switch and multiplexer hierarchy, where switches select or isolate analog signals while multiplexers combine multiple inputs into a common output. The latched control interface allows the selected signal path to remain in its commanded state without continuous control activity. The DG425DJ offers equal on-resistance matching between switches, with the manufacturer specifying 3 Ω maximum. Its typical on-resistance is 20 Ω, while flatness across the signal range is limited to 4 Ω maximum. These matching and flatness characteristics reduce channel-dependent gain and timing differences when the device is used for precision signal selection. The switch also provides bidirectional conduction, making it suitable for signal paths where the source direction can change. Charge injection is limited to 15 pC maximum, a useful specification when the switch controls sampled or held analog signals. The device provides ESD tolerance of at least 2000 V under Method 3015.7. Off leakage is specified below 5 nA at +85 °C, supporting isolation between inactive and active channels. Latch timing values include tWW of 200 ns maximum, tDW of 100 ns maximum, and tWD of 100 ns maximum. Typical applications include microprocessor-controlled signal routing, test and measurement systems, industrial control interfaces, data acquisition equipment, and analog signal multiplexing. The latch allows firmware or hardware control logic to establish a connection and then reduce switching-control activity, provided the selected state is not affected by later pulses. When laying out a DG425DJ circuit, route sensitive signals with short traces and provide a stable ground reference. Keep latch-control traces away from analog inputs because coupling from fast digital transitions can disturb held nodes or inject charge into downstream amplifiers. Confirm signal amplitude, bandwidth, leakage, and logic levels against the complete manufacturer datasheet before production use. This page combines the verified DG425DJ manufacturer and distributor information with explicit data-gap markers, application guidance, family comparisons, and selection advice. It does not substitute estimated electrical specifications for values absent from the retrieved source data.

RFQ پەیوەندی
DG428DN - Latchable 8:1 Analog Multiplexer | Vishay | ATE
DG428DN

DG428DN - Latchable 8:1 Analog Multiplexer | Vishay | ATE

The Vishay DG428DN is a latchable 8-channel single-ended or 4-channel differential analog multiplexer with a maximum on-resistance of 100 ohms, operating from -15 V to +15 V in a 20-pin PLCC package measuring 9 x 9 mm. It combines eight analog inputs, onboard TTL-compatible address latches, break-before-make switching, and low power consumption for processor-controlled signal routing. An analog multiplexer is an interface IC that connects one of several analog inputs to a common output according to a digital address. The DG428DN belongs to the broader multiplexer-switch and signal-routing hierarchy, where latched address inputs reduce the number of control signals required from a microprocessor. Its differential configuration allows two switch pairs to route paired signals, supporting balanced measurements and reducing common-mode routing complexity. The device provides a maximum on-resistance of 100 ohms, an on-state switching time of 225 ns, an off-state switching time of 300 ns, and an isolation value of 75 dB. Onboard TTL-compatible address latches permit the selected channel to remain stable between control updates. Break-before-make operation prevents two channels from being connected simultaneously during a transition, which is important for external equipment, instrumentation, and measurement systems. The DG428DN can operate with positive or negative supply voltages and also supports single-supply operation. Its absolute maximum voltage rating extends to 44 V. An epitaxial layer is designed to reduce latch-up risk, while low power consumption of 0.3 mW supports power-conscious acquisition and control systems. The address interface is compatible with microprocessor buses, reducing external logic and board-space requirements. Typical applications include data-acquisition systems, automatic test equipment, process-control equipment, avionics, instrumentation, and multiplexed sensor interfaces. A single package can route eight single-ended channels or four differential channels, making it useful where several physical inputs must share one converter, amplifier, or measurement front end. When laying out a board, keep the selected analog path short and place protection networks away from the multiplexer pins. Confirm signal swing, supply polarity, and break-before-make behavior before assigning channels to external equipment. The complete pin and package details should be checked against the Vishay datasheet before layout release. This page consolidates the DG428DN electrical characteristics, package information, replacement guidance, comparison data, and practical application guidance. It is intended to help engineers evaluate the device for multiplexed analog acquisition, test, control, and signal-routing systems.

RFQ پەیوەندی
DG429DN - 4:1 Latchable Analog Multiplexer | Vishay Siliconix
DG429DN

DG429DN - 4:1 Latchable Analog Multiplexer | Vishay Siliconix

The Vishay Siliconix DG429DN is a dual 4:1 latchable analog multiplexer IC with an on-resistance of 100 ohm, supplied in a 20-pin PLCC package measuring 9 mm by 9 mm. The device can operate as a single-ended eight-channel or differential four-channel multiplexer, with address and control latches integrated on chip. Its maximum voltage rating extends to 44 V, and single-supply operation is supported. An analog multiplexer is an interface IC that routes one of several analog inputs to an output terminal. The DG429DN belongs to the analog switch and multiplexer hierarchy, where address-controlled switching replaces multiple discrete relays or manually selected signal paths. Integrated latches make it suitable for data-acquisition systems, process control, avionics, and automated test equipment. The TTL-compatible address interface reduces external control-logic requirements while preserving microprocessor-bus compatibility. The DG429DN provides two independent 4:1 analog switching circuits. Its break-before-make operating behavior prevents momentary crosstalk between adjacent inputs during a transition. Vishay describes low on-resistance, low charge injection, and high switching speed as principal device characteristics. The typical power-consumption figure is 0.3 mW, making the IC suitable for instrumentation where signal-routing power must remain modest. On-board address latches also simplify control implementation in bus-oriented systems. The maximum analog signal voltage is 44 V, while the latchable control architecture supports single-supply operation. These characteristics make the device applicable to industrial measurement, automated test equipment, process-control systems, and avionics signal routing. The integrated latches allow a host processor or logic controller to select channels while reducing the number of external storage elements and simplifying board-level timing. Designers should examine the complete pin description and operating limits in the Vishay Siliconix datasheet before assigning signal paths. Pay particular attention to supply sequencing, allowable input and output voltages, control logic states, and the break-before-make interval. The 20-pin PLCC footprint also requires a compatible land pattern and appropriate assembly handling; the package is not one of the standard surface-mount packages represented by the site’s standard pinout library. This page combines the manufacturer’s device description, distributor listing information, and a focused comparison of documented drop-in alternatives. It also highlights the practical value of the DG429DN’s TTL-compatible latches, extended 44 V rating, single-supply capability, low 0.3 mW power consumption, and break-before-make switching for engineers designing multiplexed analog signal paths.

RFQ پەیوەندی
DG441CJ+ - Quad SPST Analog Switch | Analog Devices
DG441CJ+

DG441CJ+ - Quad SPST Analog Switch | Analog Devices

Analog Devices DG441CJ+ is a production, quad SPST CMOS analog switch with four normally closed circuits, an 85 ohm on-resistance rating, and a 16-pin DIP package. The DG441 family provides on-resistance matching of 4 ohms maximum between switches and on-resistance flatness of 9 ohms maximum across the signal range. A lead-free marking is identified by the terminal + suffix. A CMOS analog switch is a semiconductor device that routes electrical signals between terminals under digital control. It belongs to the analog switch and multiplexer hierarchy, which falls under interface ICs and ultimately semiconductor signal-management components. The DG441CJ+ uses four independent single-pole, single-throw channels. Each channel connects its common terminal to one switched terminal while remaining normally closed when no control voltage is applied. The principal advantages of the DG441CJ+ include low charge injection of 10 pC maximum, low power consumption of 1.65 mW, and ESD tolerance of 2000 V minimum. These characteristics make the device useful when a design must switch analog signals while limiting control-signal transients and maintaining consistent resistance among channels. The 85 ohm maximum on-resistance specification is important for source impedance, signal attenuation, and bandwidth calculations. The DG441 design provides symmetric low on-resistance behavior in either signal direction. Its matching specification of 4 ohms maximum reduces channel-to-channel variation, while the 9 ohms maximum flatness specification limits resistance changes over the operating signal range. These characteristics are particularly useful in instrumentation, data acquisition, test systems, and control interfaces where four channels must present similar electrical behavior. Typical uses include routing sensor outputs into an analog-to-digital converter, selecting test points in automated test equipment, switching bipolar or unipolar analog signals, and building sample-and-hold or measurement front ends. The four normally closed channels are particularly suitable when the system must maintain a defined signal connection during reset, power-up, or control transitions. PCB design should account for the relatively high 85 ohm maximum on-resistance rather than treating the switch as a low-resistance power mux. Keep analog traces short, provide a stable ground reference, and route control inputs away from sensitive analog paths. Confirm the complete pin assignment and operating limits in the manufacturer datasheet before finalizing the layout. This page combines the manufacturer product information, exact DG441CJ+ ordering information, electrical characteristics, application guidance, and drop-in replacement analysis to support faster component selection and PCB implementation.

RFQ پەیوەندی
DG441CY+ - Quad SPST 85Ω Analog Switch | Analog Devices
DG441CY+

DG441CY+ - Quad SPST 85Ω Analog Switch | Analog Devices

Analog Devices DG441CY+ is an improved quad SPST analog switch IC with four independent normally closed switches, an 85 Ω maximum on-resistance specification, and a 16-pin narrow SOIC package. The device is designed for routing low-voltage analog or digital signals when a low on-resistance, controlled off-state behavior, and compact integration are required. Its four switches support a 1:1 multiplexing configuration according to the manufacturer and distributor product listings. An analog switch is a solid-state semiconductor device that uses control logic to connect or disconnect signals without mechanically moving electrical contacts. The DG441 belongs to the analog switch and multiplexer hierarchy: analog switch IC, multiplexer/demultiplexer IC, interface IC, and integrated circuit. Compared with mechanical relays, an integrated analog switch can operate faster, consume less space, and avoid mechanical contact wear, although its voltage and current ratings remain more restrictive. The manufacturer data sheet identifies four independent SPST switches, on-resistance matching of no more than 4 Ω, on-resistance flatness of no more than 9 Ω across the signal range, and equal conduction behavior in either direction. It also specifies low charge injection of no more than 10 pC, low power consumption of 1.65 mW, and ESD tolerance of at least 2,000 V. The distributor listing identifies the DG441CY+ as a 4-circuit, 1:1 switch with 85 Ω maximum on-resistance in a 16-SOIC package. The SPST topology provides one signal path per switch, while the normally closed state establishes the conduction path before a control input changes state. This makes the device useful for controlled grounding, signal isolation, test-point routing, sample-and-hold paths, and peripheral selection. The low on-resistance matching and flatness reduce gain or timing errors when multiple channels must conduct with consistent resistance. Typical uses include test and measurement systems, data-acquisition equipment, battery-powered instruments, audio and communications equipment, and industrial control systems. The compact 16-SOIC package simplifies board integration, while the quad-channel configuration can implement several switched signal paths in one device. System designers should still verify signal amplitude, bandwidth, leakage, control logic levels, and switch lifetime against the manufacturer data sheet. The principal design consideration is off-state isolation. Although the normally closed switches provide a defined default path, leakage and capacitance can still couple adjacent signals. Keep sensitive routing paths short, use an appropriate ground reference, and control the switches with logic levels compatible with the supply voltage. This page combines verified manufacturer and distributor information, package details, comparison data, and practical replacement guidance for engineers evaluating the DG441CY+.

RFQ پەیوەندی
DG441CY+T - 4-Channel SPST Analog Switch | Analog Devices
DG441CY+T

DG441CY+T - 4-Channel SPST Analog Switch | Analog Devices

The Analog Devices DG441CY+T is a four-channel, single-pole single-throw analog switch with 85 ohm on-resistance, operating in a 16-lead SOIC package. It provides improved on-resistance matching and flatness across the signal range, making it suitable for precision signal-routing systems. The device supports single-supply operation from +10 V to +30 V and bipolar operation from ±4.5 V to ±20 V. An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The DG441 belongs to the analog switch category within the broader signal-path and power-management ecosystem. Its four independent SPST channels can connect or disconnect analog, audio, instrumentation, communication, and battery-powered system signals while minimizing insertion loss and distortion. Key features include 85 ohm maximum on-resistance, on-resistance matching of 4 ohm maximum between switches, and guaranteed on-resistance flatness of 9 ohm maximum over the signal range. The switching characteristics include turn-on time below 250 ns and turn-off time below 170 ns. These parameters make the device useful where controlled analog routing must coexist with digital control logic. The DG441 family uses a 44 V silicon-gate CMOS process. Its logic-compatible control inputs and symmetric on-state conduction support signal routing in either direction. The low matching and flatness specifications help preserve amplitude consistency when multiple channels must behave similarly, which is important in measurement, communication, and audio systems. Typical applications include audio-signal routing, battery-powered equipment, communication systems, fax equipment, instrumentation, and test systems. The device can be used to select between sensor sources, route test signals, disconnect loads, or preserve a common analog path while keeping control logic separated from the analog signal. Designers should verify the positive and negative supply limits, control-logic levels, signal-range restrictions, and maximum switch current in the manufacturer datasheet. Place bypass capacitors close to the supply pins and route control traces away from sensitive analog inputs to reduce coupling and switching transients. This product page combines package, performance, application, and selection guidance with a focused comparison against pin-compatible DG441-family devices. It is intended to help engineers identify the correct supply configuration, package variant, and replacement option before integrating the switch into a PCB design.

RFQ پەیوەندی
DG441DJ+ - Quad SPST Analog Switch | Vishay | 16-DIP
DG441DJ+

DG441DJ+ - Quad SPST Analog Switch | Vishay | 16-DIP

Vishay Intertechnology DG441DJ+ is a low-power, quad SPST CMOS analog switch with four independent 1:1 signal paths, 85 Ω typical on-resistance, and a 16-pin DIP package. It supports positive and negative analog supplies, with operating ranges of 10 V to 30 V for dual supply operation and 4.5 V to 20 V for single-supply operation. The device is designed for routing low-voltage analog signals where compact logic control, low power consumption, and bidirectional conduction are useful. An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. A single-pole single-throw, or SPST, switch provides one independently controlled conducting path. As a CMOS analog switch, the DG441DJ+ belongs to the interface IC category and uses MOSFET structures to achieve low on-resistance, low leakage, and low control power. Unlike a mechanical relay, it switches much faster and consumes no sustained coil energy. Key electrical features include a low typical on-resistance of 85 Ω, on-resistance matching of 4 Ω maximum between switches, and on-resistance flatness of 9 Ω maximum over the signal range. The switch operates equally well in either direction. Low leakage of 80 pA and a switching time of 150 ns make it useful for precision signal routing, while the 16-pin DIP package supports conventional through-hole PCB assembly. The manufacturer documentation describes improved DG201A and DG202-series compatibility, TTL/CMOS-compatible control logic, and single-supply capability. Different versions of the family documentation list different power-consumption figures, including 0.2 mW in legacy family material and 1.65 mW in revised documentation; the applicable production datasheet should therefore govern final design decisions. The verified product listing identifies the DG441DJ+ as a quad SPST switch in a 16-pin DIP package. Typical uses include data-acquisition systems, sensor multiplexing, analog test equipment, sample-and-hold circuits, battery-powered instruments, and precision measurement front ends. The four independent switches can route four signals independently or be controlled in coordinated sequences. Because on-resistance can vary with signal voltage, analog engineers should account for the specified resistance and flatness when calculating gains and settling behavior. A key design consideration is the relationship between control levels and supply voltage. TTL/CMOS-compatible logic simplifies interfacing, but the selected supply configuration and input levels must remain within the manufacturer limits. The DIP package also requires adequate spacing around the leads for soldering and cleaning, while signal traces should remain short to minimize added capacitance and coupling during the 150 ns switching transition. This page consolidates manufacturer documentation, distributor identification, package information, and verified cross-reference information into an engineering-focused guide. It also distinguishes confirmed drop-in candidates from unsupported alternatives, making the comparison more useful than a basic distributor listing when PCB footprint, switch function, and supply compatibility must be verified before substitution.

RFQ پەیوەندی
DG441DJZ - Quad SPST NC 85Ohm Analog Switch | Renesas
DG441DJZ

DG441DJZ - Quad SPST NC 85Ohm Analog Switch | Renesas

The Renesas Electronics DG441DJZ is a monolithic quad SPST normally-closed CMOS analog switch IC with 85 ohm maximum on-resistance, operating from a total supply range of 5V to 34V (typically +/-15V rails), housed in a 16-pin PDIP package. It contains four independent single-pole single-throw switches with TTL and CMOS compatible logic inputs and an internal voltage reference for logic thresholds. An analog switch is a semiconductor device that routes or blocks analog signal paths under digital control, sitting within the broader hierarchy of signal-switching devices: analog switch, multiplexer/demultiplexer family, and interface ICs. Quad SPST switches are favored where independent, per-channel on/off control of four signal lines is needed without combining channels into a common bus, as a conventional multiplexer would require. Key features of the DG441DJZ include four independently addressable normally-closed switches, 85 ohm guaranteed maximum on-resistance, TTL and CMOS logic compatibility across the full supply range, and drop-in compatibility with the popular DG201A and DG202 series devices. The DJZ suffix denotes the industrial temperature grade in a 16-pin plastic DIP package, supporting through-hole assembly for industrial and instrumentation designs. Architecturally, the DG441 family uses monolithic CMOS construction that conducts equally well in either signal direction, allowing bidirectional signal flow. An internal voltage reference stabilizes logic thresholds against supply variation, keeping switching thresholds deterministic when driven by TTL or CMOS logic over the specified operating range. Typical applications include precision test and measurement signal routing, industrial programmable logic controller (PLC) analog front ends, audio and video signal switching, sample-and-hold circuits, and communication equipment relay replacement where solid-state switching improves reliability and eliminates contact bounce. When designing with the DG441DJZ, observe supply sequencing and ensure signal swings stay within the supply rails to prevent latch-up; the normally-closed configuration means channels conduct at power-off logic states, which must be considered in fail-safe designs. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
DG441DY+ - 4-Channel SPST Analog Switch | Analog Devices
DG441DY+

DG441DY+ - 4-Channel SPST Analog Switch | Analog Devices

Analog Devices DG441DY+ is an improved quad SPST normally closed analog switch with four independent 1:1 channels, an 85 Ω maximum on-resistance, and a 16-SOIC package. It operates from 4.5 V to 20 V, supports dual supplies from 10 V to 30 V, and provides low charge injection of 10 pC maximum with power consumption of 1.65 mW. An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. The DG441DY+ belongs to the analog-switch hierarchy, where it functions as an interface IC between low-power control logic and external analog signals. Its normally closed configuration provides a defined signal connection before the control input commands a change of state, making it useful in routing, sampling, test, and signal-isolation systems. The device uses four independent SPST-NC channels rather than a multiplexer arrangement. According to the Analog Devices DG441-DG442 datasheet, the redesigned DG441 family provides on-resistance matching of 4 Ω maximum between switches and on-resistance flatness of 9 Ω maximum over the signal range. Each channel conducts equally well in either direction, which supports signal-path designs where input and output roles may change. The DG441DY+ is specified for low power consumption of 1.65 mW and low charge injection of 10 pC maximum. Charge injection is important when switching precision, high-impedance analog nodes because control-clock energy can otherwise appear as an unwanted voltage step. The device also has an ESD tolerance of 2000 V minimum, providing a defined electrostatic-protection capability for exposed analog interfaces. Typical applications include battery-powered test equipment, data-acquisition systems, audio and measurement signal routing, industrial control interfaces, and precision sensor connections. Four independent switches in one 16-SOIC package reduce board area and permit several signal paths to be switched under a common control interface. The dual-supply capability also allows designers to switch bipolar signals when the system provides the required positive and negative rails. When designing a board around the DG441DY+, verify the normally closed signal state during power-up and ensure that every switched node remains within the specified 4.5 V to 20 V single-supply or 10 V to 30 V dual-supply limits. Use the manufacturer pinout and truth table for the exact DY package rather than assuming that a multiplexer's address and enable functions are present. This product data consolidates manufacturer specifications, current distributor availability, package details, and verified drop-in replacement information. It also provides application guidance and selection trade-offs that help engineers move from the datasheet to a production-ready PCB design.

RFQ پەیوەندی
DG441DY+T - Quad SPST Analog Switch, 16-SOIC | Analog Devices
DG441DY+T

DG441DY+T - Quad SPST Analog Switch, 16-SOIC | Analog Devices

The Analog Devices DG441DY+T is an improved quad SPST CMOS analog switch in a 16-SOIC package, providing four independent single-pole single-throw switches with a nominal 85 ohm on-resistance rating and 1:1 signal routing. The device accepts a single supply from +10 V to +30 V or a bipolar supply from ±4.5 V to ±20 V, and its switching times are specified below 250 ns for turn-on and below 170 ns for turn-off. An analog switch is a semiconductor device that routes an analog signal between terminals under digital control. The DG441 family belongs to the switch and multiplexer hierarchy, where an analog switch provides one independently controlled connection per channel. Unlike a mechanical relay, the DG441DY+T changes connection state electronically with low actuation delay, making it appropriate for high-speed signal selection where the signal bandwidth remains below the switch's switching capabilities. Each of the four channels is a normally closed SPST arrangement, and the control inputs are compatible with TTL and CMOS logic. The DG441 includes an internal voltage reference for its logic thresholds, helping the device operate predictably across compatible supply conditions. Vishay documentation describes the DG441 family as a low-on-resistance, high-speed CMOS switch intended as a drop-in replacement for the DG201A and DG202 series. Typical uses include audio-signal routing, sample-and-hold circuits, battery-powered instrumentation, communication systems, and general analog signal multiplexing. The four independent switches allow one package to route several signals without sharing a common drain. Maximum signal amplitude and supply combinations should remain within the ratings published in the manufacturer data sheet because the analog switch is not a substitute for an input protection network. The 16-SOIC package provides ample pin spacing for manual assembly and conventional PCB routing. Place each switched signal trace away from high-energy digital and switching-node traces, and route the four control inputs directly to their drivers to avoid capacitive coupling during switching transitions. Decoupling capacitors should be placed near the supply pins, while unused control inputs must be driven to a defined logic level rather than left floating. This page combines the DG441 family electrical characteristics, package information, drop-in alternatives, and application-specific design guidance to help engineers compare the DG441DY+T against equivalent quad SPST analog switches without relying on a distributor summary alone.

RFQ پەیوەندی
DG441DYZ - Quad SPST CMOS Analog Switch, 85Ω, 16-SOIC | Renesas
DG441DYZ

DG441DYZ - Quad SPST CMOS Analog Switch, 85Ω, 16-SOIC | Renesas

The Renesas DG441DYZ is a monolithic quad SPST (Single-Pole Single-Throw) CMOS analog switch in a 16-pin SOIC package, designed as a drop-in upgrade for legacy DG201A and DG202 series devices. It integrates four independent SPST switches with 85Ω on-resistance, TTL/CMOS-compatible digital inputs, and an on-chip voltage reference that drives the logic threshold translators. The device operates from a single +5V to +34V supply, from symmetrical ±5V to ±22V supplies, or from asymmetric rails bounded by a 44V maximum, allowing control of signals up to 40V peak-to-peak. An analog switch (also called a CMOS transmission gate or bilateral switch) is a solid-state device that uses MOSFET transistors to pass or block analog and digital signals with very low distortion. The DG441DYZ belongs to the SPST switch family, which functions like a mechanical relay but with faster switching speed, no contact bounce, low power consumption, and bounce-free operation. It sits inside the broader analog switch IC category, alongside multiplexers (MUX), demultiplexers (DEMUX), and cross-point switches, all of which are sub-categories of interface ICs used for signal routing in mixed-signal systems. Key features include 85Ω typical on-resistance, 250 ns turn-on time (tON), a -3 dB bandwidth of approximately 200 MHz, and sub-nanoamp leakage currents. The switch architecture uses a high-voltage silicon-gate CMOS process with an epitaxial layer that prevents latch-up, a reliability concern common to older CMOS analog switches. Each switch exhibits low charge injection, making the part suitable for sample-and-hold circuits and precision multiplexed data-acquisition front-ends. The DG441DYZ is widely deployed in industrial process control, instrumentation, automatic test equipment (ATE), battery-powered telemetry, communication systems, and audio/video signal routing. Its wide supply range, low on-resistance flatness across the signal range, and TTL-compatible logic make it a versatile replacement for electromechanical relays where reliability, size, and switching speed are design constraints. The 16-SOIC (0.154" / 3.90 mm body width) package is pin-compatible with legacy DG201A/DG202 SOIC footprints, allowing direct PCB drop-in upgrades. When designing with the DG441DYZ, observe absolute maximum signal ratings of 44V across the switch and ensure logic inputs do not exceed V+ plus 0.3V. For low-impedance sources, account for the 85Ω on-resistance and its flatness over the analog signal range; for high-impedance loads, the dominant error source is leakage rather than Ron. Always decouple the supply pins with a 0.1 µF ceramic capacitor placed as close to the device as possible to minimize digital-induced noise coupling into the analog path. This page consolidates distributor pricing, AEC-Q-free drop-in alternatives, and PCB-level design notes that extend beyond the Renesas datasheet's typical application circuits to help engineers choose the right analog switch family for production.

RFQ پەیوەندی
DG442CJ+ - 85Ω Quad SPST Analog Switch | Maxim Integrated
DG442CJ+

DG442CJ+ - 85Ω Quad SPST Analog Switch | Maxim Integrated

The Maxim Integrated DG442CJ+ is a four-circuit, single-pole single-throw CMOS analog switch with an 85Ω on-resistance, 1:1 signal routing, normally open contacts, and a 16-pin PDIP package. The device supports bidirectional signal conduction, provides break-before-make switching, and is designed for analog multiplexing, demultiplexing, sample-and-hold, and general signal-routing applications where a compact through-hole quad switch is required. An analog switch is an electronic routing component that connects or disconnects signal paths under digital control. A SPST switch provides one selectable path, while the DG442CJ+ combines four independent switches in one IC. The normally open configuration leaves each path disconnected until its control signal activates it. Within the interface-IC hierarchy, this device is a CMOS analog switch that bridges external analog circuitry and control logic. The DG442CJ+ uses an 85Ω on-resistance and supports bidirectional operation. Maxim redesigned the DG441 and DG442 families to guarantee on-resistance matching of 4Ω maximum between switches and on-resistance flatness of 9Ω maximum over the signal range. These characteristics help reduce channel-to-channel error when several switched paths must present similar impedance to the source or load. Switching timing includes approximately 170ns and 250ns figures identified for the device family, while the listed off-leakage is 500pA. These characteristics make the switch suitable for moderate-bandwidth analog paths, particularly where low leakage matters more than sub-nanosecond switching performance. The device is identified as a commercial-grade, through-hole part in a rectangular 16-pin PDIP package measuring approximately 0.300 inch wide, or 7.62mm. Typical uses include test-equipment signal routing, precision measurement front ends, audio path selection, data acquisition systems, and industrial control interfaces. Four integrated switches reduce component count compared with four separate single-switch packages, while the parallel normally open structure simplifies channel isolation. The 85Ω impedance should be included in the source and load calculations because it can attenuate high-impedance signals and limit operation at higher frequencies. PCB design should preserve short analog traces, provide a solid ground reference, and keep switching-node capacitance away from sensitive input paths. Because the device is a normally open SPST switch, evaluate whether break-before-make behavior satisfies the application’s interruption requirements. Use the manufacturer pin-description table and typical application circuits when assigning control signals and confirming the connection sequence. This page combines package details, verified distributor records, drop-in replacement guidance, comparison parameters, and practical routing considerations to support faster component selection. It also distinguishes confirmed electrical and package facts from parameters that require confirmation in the manufacturer datasheet.

RFQ پەیوەندی
DG442CY+ - 85Ω Quad SPST Analog Switch | Analog Devices
DG442CY+

DG442CY+ - 85Ω Quad SPST Analog Switch | Analog Devices

Analog Devices DG442CY+ is a four-circuit, normally open SPST CMOS analog switch with an 85Ω on-resistance, supplied in a 16-pin SOIC package. The device uses four independent 1:1 switches, supports bidirectional signal conduction, and provides matched on-resistance of 4Ω maximum between switches. Its guaranteed on-resistance flatness is 9Ω maximum over the signal range, helping preserve signal amplitude consistency across the four channels. An analog switch is a semiconductor interface that connects or isolates a signal path under digital control. The DG442CY+ belongs to the analog switch and multiplexer hierarchy, where multiplexers combine switching functions with channel-selection logic. Unlike mechanical relays, this CMOS implementation offers compact integration, fast electronic control, low charge injection of 10pC maximum, and low power consumption of 1.65mW. These characteristics make it useful where several independent analog signals must be routed on a compact circuit board. Key features include four normally open SPST channels, an 85Ω on-resistance, 4Ω maximum on-resistance matching between switches, and 9Ω maximum on-resistance flatness over the signal range. The switches conduct equally well in either direction, which simplifies routing design when the source and destination can alternate roles. Charge injection of 10pC maximum helps limit control-transition disturbance, while the low 1.65mW power consumption supports space-constrained and portable equipment. The DG442CY+ is implemented as a monolithic CMOS analog-switch circuit with four independent control paths. Its matched channel resistance reduces gain variation between similarly driven switches, while the controlled flatness limits amplitude distortion as the analog voltage changes. The bidirectional conduction characteristic allows the same device architecture to support source selection, signal isolation, test-point routing, and power-routing functions when voltage, current, and switching-transient limits remain acceptable. Typical applications include audio routing, test and measurement systems, instrumentation, industrial control interfaces, sample-and-hold isolation, and compact embedded signal-conditioning systems. In these applications, the four-channel architecture can route one control signal to four different destinations or isolate several test nodes without requiring four separate packages. Designers should still verify the complete operating-voltage, leakage-current, and switching-time limits against their signal range because those values are not included in the supplied verified excerpts. The primary design consideration is ensuring that switch operation, control-logic levels, and analog signal limits are compatible with the target system. Place the device close to the routed signals to minimize PCB trace capacitance and susceptibility to injection from adjacent switching circuitry. Use a defined ground reference and route control inputs away from sensitive analog nodes. Confirm power-supply sequencing and ensure signal voltages never exceed the device's absolute maximum ratings before enabling the switches. This product record combines the supplied manufacturer and distributor findings with structured comparisons, drop-in alternatives, and application-focused engineering guidance. It also distinguishes verified parameters from information still requiring confirmation from the complete DG441/DG442 datasheet, helping engineers make a defensible sourcing and design decision without converting unsupported assumptions into specifications.

RFQ پەیوەندی
DG442DJ+ - Quad SPST 85Ω Analog Switch | Vishay Intertechnology
DG442DJ+

DG442DJ+ - Quad SPST 85Ω Analog Switch | Vishay Intertechnology

The Vishay Intertechnology DG442DJ+ is a monolithic quad SPST CMOS analog switch with four independent 1:1 circuits, an 85 Ω on-resistance, and a 16-pin PDIP package. It is designed for analog signal routing where four independently controlled switches are required within one package. The device uses CMOS-compatible control inputs and supports analog switching across signal ranges referenced in the manufacturer documentation. An analog switch is a semiconductor-controlled routing component that connects or disconnects analog signal paths. The DG442DJ belongs to the monolithic CMOS analog-switch hierarchy, where SPST describes one switch path per circuit and quad describes four independent channels. Unlike a multiplexer, each DG442 channel can operate independently rather than sharing a common internal signal path. Key features include four independent SPST switch circuits, an 85 Ω on-resistance, and 1:1 signal routing. The package is a 16-pin PDIP, allowing through-hole assembly and straightforward prototyping. The available product information identifies the DG441 and DG442 families as drop-in replacements for the popular DG201A and DG202 series, which helps engineers evaluate PCB reuse and upgrade paths. Internally, the DG442 uses a monolithic CMOS implementation to provide consistent switching behavior across the four channels. Each channel has a corresponding control input and common ground and power connections. Designers should consult the manufacturer datasheet for the exact control truth table, input and supply limits, switching timing, off-impedance, leakage, and absolute maximum ratings before finalizing a design. Typical uses include analog test systems, instrumentation, signal-conditioning modules, data-acquisition equipment, and industrial control circuits where multiple analog paths must be routed independently. Its four-channel arrangement can reduce component count when a design needs four SPST functions rather than four separate single switch packages. The primary design consideration is confirming that the DG442DJ+ control polarity and timing satisfy the receiving circuit. Because the verified source data does not provide a complete pin table, engineers should verify every connection against the manufacturer datasheet before PCB release. Input signals must also remain within the specified voltage limits. This page consolidates verified distributor information, compatible replacement data, package details, selection guidance, and practical design notes into one engineering-focused resource for the DG442DJ+.

RFQ پەیوەندی
DG442DK - 85 Ohm Quad SPST Analog Switch | Maxim Integrated | 16-CDIP
DG442DK

DG442DK - 85 Ohm Quad SPST Analog Switch | Maxim Integrated | 16-CDIP

The Maxim Integrated DG442DK is a quad SPST analog switch IC with 85 ohm maximum on-resistance, 500 pA off-leakage current and 250 ns turn-on time, packaged in a 16-pin ceramic DIP (16-CDIP, 0.300 inch / 7.62 mm lead pitch). It provides four independent single-pole single-throw switches in a 1:1 configuration, each able to route a bipolar analog signal, and operates from a 15 V supply. What is an analog switch? An analog switch is a solid-state semiconductor device that steers analog signals between circuit nodes under digital control, with no moving contacts and near-zero off-state signal transfer. A single-pole single-throw (SPST) analog switch provides one conducting path that is opened or closed, and a quad SPST device like the DG442DK implements four such paths on one die. In the product hierarchy, an analog switch sits within analog multiplexers and demultiplexers, inside interface ICs, within the broader family of integrated circuits and semiconductors. The DG442DK is a discrete-control (no logic-enable) version, so each of the four paths is driven by its own external control signal. Key features of the DG442DK include a maximum on-resistance of 85 ohm with on-resistance matching between switches guaranteed to 4 ohm maximum, and on-resistance flatness over the signal range guaranteed to 9 ohm maximum. The matched and flat resistance characteristics mean all four channels attenuate the same signal equally, which is what makes the device usable in balanced multi-channel paths rather than only in single-channel routing. Off-leakage current of 500 pA keeps the off state effectively open for high-impedance sources, and the switch conducts equally well in either signal direction. The Maxim Integrated DG441/DG442 family was redesigned around improved on-resistance matching and guaranteed on-resistance flatness over the signal range, replacing older revision behavior where channel-to-channel Ron could drift more widely. Switching times of 250 ns turn-on and 170 ns turn-off place the part in the general-purpose, medium-speed class rather than the sub-10 ns RF or ultra-fast video switch categories, which keeps on-resistance and leakage low while remaining inexpensive and easy to drive from standard logic. Typical applications include signal multiplexing in automated test and measurement equipment, audio and instrumentation channel selection, sample-and-hold and guarded-input amplifier front ends, and battery-powered sensor interface boards where the 500 pA off leakage protects the source from loading. Because the switches are independent, four different signal paths can be routed simultaneously to four different destinations. One key design consideration is that each switch has no on-board enable logic, so control drive levels and timing are entirely set by the host logic. Because the ceramic DIP package provides long leads, it also tolerates higher applied signal voltages relative to the 15 V supply in many analog-routing applications, but the signal range must always remain inside the absolute maximum ratings given in the manufacturer datasheet. This page consolidates package details, switching characteristics, drop-in source options and practical layout guidance for the DG442DK, adding engineering context that is not present in the raw manufacturer datasheet listings.

RFQ پەیوەندی
DG442DY+ Quad SPST Analog Switch | Maxim Integrated
DG442DY+

DG442DY+ Quad SPST Analog Switch | Maxim Integrated

The Maxim Integrated DG442DY+ is a four-channel, single-pole single-throw CMOS analog switch with a 1:1 signal configuration, 85 ohm typical on-resistance, and a 16-pin SOIC package. It provides four independently controlled switches for routing analog or digital signals in test, measurement, instrumentation, and communication equipment. A CMOS analog switch is a semiconductor-based selection device that connects or isolates signal paths under digital control. Unlike a mechanical relay, it operates without moving contacts, allowing faster switching and compact integration. The DG442DY+ belongs to the analog-switch hierarchy, where each SPST channel provides one conductive path and a separate control input. Its four-channel structure consolidates multiple routing functions into one package while keeping the PCB footprint straightforward. The principal benefits are low on-resistance, low leakage, low power consumption, and improved matching and flatness among the four channels. Maxim describes the redesigned DG441/DG442 family as providing on-resistance matching within 4 ohms maximum between switches and on-resistance flatness within 9 ohms maximum over the signal range. The low-resistance behavior helps minimize signal attenuation when the switch is closed, while matching reduces channel-to-channel gain and timing inconsistencies in precision circuits. The DG442DY+ uses CMOS construction to limit power consumption and provide high input impedance. Each channel can connect its corresponding terminal to its common terminal when asserted. Because the device has four independent control inputs, it can route different signals simultaneously. Designers should still account for switch logic polarity, signal-level limits, off-state leakage, charge injection, and switching transients when evaluating precision or high-impedance applications. Typical uses include automated test equipment, data-acquisition systems, sample-and-hold circuits, signal multiplexing, instrumentation front ends, and communication equipment. The same four-channel structure can also be used to connect external sensors, select measurement paths, isolate signal sources, or implement controlled signal-routing networks where the system requires more than one independent analog connection. For PCB implementation, place the device close to the routed signal paths to minimize trace resistance and capacitance. Keep sensitive analog traces away from high-energy switching nodes, provide a stable ground reference, and use the manufacturer pin-description table when assigning controls and common terminals. Decoupling and exposed-pad requirements are package-specific; verify the exact lead configuration and land pattern before releasing artwork. This product reference combines the DG442DY+ electrical characteristics, package information, sourcing details, strict same-footprint alternatives, comparison data, and practical implementation guidance. It helps engineers evaluate the switch for signal-integrity, routing, and design-in decisions without relying on a simple distributor listing alone.

RFQ پەیوەندی
DG442DY+T - 4-Channel SPST Analog Switch | Analog Devices
DG442DY+T

DG442DY+T - 4-Channel SPST Analog Switch | Analog Devices

Analog Devices DG442DY+T is a monolithic CMOS analog switch containing four independent single-pole single-throw (SPST) switches in a 16-lead narrow SOIC package. Each switch presents an 85 ohm on-resistance and is controlled by TTL- and CMOS-compatible digital inputs. The device is designed for routing analog signals in test equipment, instrumentation, communications, industrial control, and signal-conditioning systems. An analog switch is an electrically controlled semiconductor device that connects or disconnects an analog signal path. The DG442 belongs to the analog-switch hierarchy, which also includes multiplexers, selectors, and matrix switches. Unlike a mechanical relay, it can change state rapidly without mechanical wear. Its four independent SPST channels provide separate signal paths while sharing common positive and negative supply rails. The DG442DY+T uses TTL-compatible and CMOS-compatible control inputs, allowing its digital control signals to be driven by common microcontrollers, FPGA logic, comparators, and other digital controllers. Its 85 ohm on-resistance is suitable for many moderate-impedance instrumentation and test circuits. The 1:1 configuration means that each switched path presents one on-resistance rather than dividing a signal through a multiplexer network. The Renesas DG441 and DG442 family datasheet identifies the DG442 as a CMOS analog switch with four independent SPST channels and a voltage reference for logic thresholds. These characteristics make the part appropriate when deterministic control logic and repeatable analog-path routing are required. The improved DG442 positioning is relevant when upgrading systems that used older DG201A and DG202-family switches. Typical uses include multimeter and oscilloscope input routing, automated test equipment, data-acquisition modules, sample-and-hold circuits, battery-powered instruments, and industrial control systems. The device can route low-frequency baseband signals without the switching transients associated with electromechanical relays. Applications should still verify signal amplitude, bandwidth, charge injection, leakage, and power-supply limits against the manufacturer datasheet. The DG442DY+T is supplied in a 16-lead SOIC measuring 3.9 mm by 9.9 mm by 1.55 mm. Place the device close to the controlled signal paths and keep analog traces short to minimize parasitic capacitance and pickup. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, and observe the stated supply sequencing and input-voltage limits before applying signals. This product page combines package information, source-backed functional characteristics, same-footprint replacement options, comparison data, and practical PCB guidance. It helps engineers identify whether the four-channel SPST architecture matches the required signal-routing task before beginning a production design.

RFQ پەیوەندی
DG444CJ+ - 4-Channel SPST Analog Switch | Analog Devices
DG444CJ+

DG444CJ+ - 4-Channel SPST Analog Switch | Analog Devices

The Analog Devices DG444CJ+ is an improved quad SPST analog switch with four independently controlled channels, an 85 ohm maximum on-resistance, and a 16-pin PDIP package. It is designed for low-power analog signal routing and supports positive supplies from 10 V to 30 V and dual supplies from ±4.5 V to ±20 V according to the manufacturer datasheet. The normally closed configuration routes the selected external signal to the common terminal when the corresponding control input is low. An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. The DG444CJ+ belongs to the analog switch hierarchy, where analog switches form part of interface ICs used for routing, sampling, test, measurement, and communication signals. Its quad-channel architecture allows four switches to share one IC while retaining individual control signals, reducing component count compared with four discrete single-channel switches. The redesigned DG444 family provides low on-resistance matching between switches of 4 ohm maximum and guaranteed on-resistance flatness over the signal range of 9 ohm maximum. These characteristics help minimize channel-to-channel resistance variation and distortion when multiple signals share the same switching network. The 85 ohm maximum on-resistance rating also makes the device suitable for circuits where moderate insertion resistance is acceptable. Each channel is configured as SPST, normally closed, and the switches conduct equally well in either signal direction. The symmetric behavior makes the DG444CJ+ useful when source and destination may swap roles, provided the designer accounts for the device's power dissipation and off-state isolation. The 16-pin PDIP package also favors through-hole prototyping, inspection, and socket-based assembly rather than compact surface-mount production. Typical uses include sample-and-hold systems, instrumentation, industrial control, communications equipment, test equipment, and audio or measurement signal routing. The DG444CJ+ is most appropriate when four independently controlled normally closed paths are required and an 85 ohm maximum on-resistance is sufficient for the application. For designs requiring lower resistance, smaller size, faster switching, or a different fault configuration, the system requirements should be checked against other analog-switch families rather than assuming pin compatibility. When laying out a design, keep sensitive signal paths short and provide adequate bypassing near the supply pins. Check the control-logic truth table, allowed input voltage range, and maximum switch current from the manufacturer datasheet. Because the device dissipates power as (VIN - VOUT) multiplied by current in the conducting state, analyze both channel and package heating at worst-case current. This page combines verified manufacturer and distributor information with pricing, package guidance, replacement analysis, and practical design notes to support component selection and PCB planning.

RFQ پەیوەندی
DG444DJ+ - Quad SPST Analog Switch, 85 ohm, 16-DIP
DG444DJ+

DG444DJ+ - Quad SPST Analog Switch, 85 ohm, 16-DIP

The Analog Devices DG444DJ+ is a quad SPST CMOS analog switch with four independent normally open switches, an 85 ohm maximum on-resistance, and a 16-pin PDIP package. The device supports positive and negative supply voltages from ±4.5 V to ±20 V, corresponding to a 10 V to 30 V total supply range, and operates across the industrial temperature range. Its four channels can route bipolar analog signals while TTL- and CMOS-compatible control inputs simplify interfacing with digital control logic. An analog switch is a solid-state semiconductor device that connects or isolates circuit nodes under digital control. The DG444 belongs to the CMOS analog-switch family within the broader interface-IC hierarchy. Unlike mechanical relays, it operates without moving contacts, allowing faster switching, compact integration, and low control-power consumption. This quad SPST arrangement is useful wherever several independent analog paths must be sampled, routed, or isolated. Key features include four independent SPST channels, low on-resistance, low leakage, fast switching, low power consumption, and TTL/CMOS-compatible logic inputs. According to the manufacturer datasheet, the on-resistance matching between switches is limited to 4 ohms maximum, while guaranteed on-resistance flatness across the signal range is limited to 9 ohms maximum. These characteristics improve channel-to-channel consistency and reduce gain variation when the same switch type is used in multiple signal paths. The DG444 family is built to provide predictable operation in precision analog systems. On-resistance matching limits channel mismatch, while low leakage helps preserve weakly driven signals when a channel is disconnected. Fast switching action supports measurement, test, and sampling systems in which the control system must select a new source quickly. Because the switches are CMOS devices, control inputs can operate from standard digital logic families, allowing a microcontroller or programmable logic device to manage channel selection. Typical uses include sample-and-hold circuits, test and measurement systems, multiplexed instrumentation, battery-powered test equipment, and signal-routing modules. The four normally open switches can independently connect an external analog node to one of four internal or external destinations. In bidirectional signal paths, the switch conducts equally well in either direction, which supports measurement and audio-oriented circuits where the signal source may change. For PCB design, place the DG444DJ+ close to the routed analog nodes to minimize trace capacitance and pickup. Keep high-impedance paths short, provide a stable ground reference, and route digital control traces away from sensitive analog inputs. Check supply decoupling at the IC and ensure control signals remain within the datasheet limits during power-up and power-down. This page combines the DG444 family specifications, verified source links, same-package drop-in candidates, application guidance, and design considerations to help engineers evaluate the DG444DJ+ before integrating it into a new analog-routing design.

RFQ پەیوەندی
DG444DY+ - 85 Ohm Quad SPST CMOS Analog Switch | Maxim
DG444DY+

DG444DY+ - 85 Ohm Quad SPST CMOS Analog Switch | Maxim

The Maxim Integrated DG444DY+ is a quad SPST CMOS analog switch with a maximum on-resistance of 85 ohm, four independent switch channels, and a 250 ns maximum on-time. The device is packaged in a 16-pin SOIC and uses TTL- and CMOS-compatible control inputs. Its four switches can route one analog or digital signal independently in either direction. An analog switch is a solid-state routing element that connects or disconnects signal paths under digital control. The DG444 belongs to the interface IC hierarchy, where analog switches sit above multiplexers, demultiplexers, and general-purpose signal-routing components. Unlike a mechanical relay, the DG444DY+ has no moving contacts, allowing fast switching, low power consumption, and compact integration into analog measurement, test, and communication equipment. Important DG444DY+ features include low on-resistance, low leakage, low power consumption, and low charge injection. According to the Vishay DG444 data sheet, the DG444 and DG445 families use a high-voltage silicon-gate process, while an epitaxial layer helps prevent latchup. The redesigned DG444 series also specifies on-resistance matching between switches of 4 ohm maximum and guaranteed on-resistance flatness of 9 ohm maximum over the signal range. The DG444DY+ contains four independent single-pole, single-throw switches. Each channel can conduct signal flow in either direction, allowing the same device to implement signal selection, source multiplexing, sample-and-hold routing, test-point isolation, and programmable gain-stage feedback control. Its monolithic CMOS construction supports compact, low-power designs, while the 16-pin SOIC package allows conventional surface-mount assembly and straightforward PCB footprint matching with compatible quad-SPST switch families. Typical uses include multimeter and oscilloscope input routing, automated test equipment, audio path selection, data acquisition systems, and instrumentation where several analog nodes must connect to a shared measurement path. The DG444DY+ is also appropriate where TTL-compatible or CMOS-compatible control levels are available and where switching speed and low off leakage are more important than very low on-resistance. When laying out a DG444DY+ circuit, place the device close to the switched signal nodes to minimize parasitic capacitance and coupling. Keep control traces away from sensitive analog conductors, use a defined return path for digital control signals, and confirm the actual signal amplitude against the device's absolute maximum ratings. Verify the exact power-supply and signal-range limits in the manufacturer data sheet before applying the part to a new design. This page combines verified manufacturer and distributor information, package-level drop-in alternatives, a parameter comparison, and practical PCB guidance. It is intended to help engineers evaluate the DG444DY+ faster than by reading the datasheet alone, while clearly separating documented values from specifications that still require confirmation.

RFQ پەیوەندی
DG444DY+T - 85Ω Quad SPST Analog Switch | Analog Devices
DG444DY+T

DG444DY+T - 85Ω Quad SPST Analog Switch | Analog Devices

The Analog Devices DG444DY+T is a four-channel, 1:1 single-pole single-throw CMOS analog switch with 85Ω on-resistance, housed in a 16-pin SOIC package. Each of its four independent switches routes a signal without changing its basic direction, while TTL- and CMOS-compatible control inputs support modern digital control systems. The device is intended for precision signal-routing, test, measurement, communication, and industrial-control systems where compact packaging and four channels in one IC reduce board area. An analog switch is a semiconductor device that uses control signals to connect or disconnect an analog signal path. A SPST switch provides one conducting path when enabled and an open circuit when disabled. The DG444 belongs to the analog-switch category within interface ICs and semiconductor devices. Four independent SPST switches packaged together allow one control IC to manage multiple test points, sensor inputs, acquisition channels, or signal-isolation paths without requiring four separate switch packages. The DG444 family provides specified on-resistance matching of 4Ω maximum between switches and guaranteed on-resistance flatness of 9Ω maximum over the signal range. These characteristics reduce channel-to-channel variation and distortion when the same switch IC performs multiple measurements or routes comparable signal amplitudes. The 85Ω on-resistance identifies the part as suitable for many general-purpose analog-routing tasks where low resistance is not the primary requirement. The monolithic CMOS implementation combines four independent switches in one package. According to the Renesas DG444/DG445 datasheet, the family uses TTL- and CMOS-compatible digital inputs, allowing direct control from common logic families. The Vishay DG444 documentation also identifies a high-voltage silicon-gate process and an epitaxial layer intended to prevent latchup. These characteristics make controlled signal routing possible while improving robustness in systems where static or transient electrical conditions must be considered. Typical applications include automated test-equipment routing, data-acquisition systems, industrial measurement interfaces, sample-and-hold circuitry, and communication equipment. Quad SPST architecture is especially useful when a system must select between multiple external lines while keeping control logic compact. The 16-pin SOIC package also suits conventional surface-mount PCB assembly and provides adequate pin density for four control inputs and eight signal terminals. For layout, route each switched signal with a short and continuous trace to minimize parasitic capacitance and resistance. Place input and output decoupling near the associated supply pins, and keep control traces away from sensitive analog nodes to reduce capacitive coupling. Check the control logic levels, allowable analog signal range, and on-state behavior in the manufacturer datasheet before finalizing the schematic or substituting a different switch implementation. This product page combines the manufacturer family information with distributor package details, pin-compatible replacement analysis, parameter comparisons, and practical PCB guidance. It is designed to help engineers identify the correct switch function, verify footprint compatibility, and plan signal-routing layouts for new or existing circuit-board designs.

RFQ پەیوەندی