بەرهەمەکان (5,100+)

DS90C363MTDX - 18-Bit 65MHz LVDS FPD-Link Transmitter | Texas Instruments
DS90C363MTDX

DS90C363MTDX - 18-Bit 65MHz LVDS FPD-Link Transmitter | Texas Instruments

The Texas Instruments DS90C363MTDX is a 3.3 V programmable LVDS transmitter for 18-bit flat-panel display links, operating at up to 65 MHz and incorporating an 18-bit parallel data interface, low-voltage differential signaling, and a 48-pin TSSOP package. The interface supports a reported data rate of 1,300 Mbps, making it intended for high-speed pixel transmission between graphics processing and display timing circuitry. An LVDS transmitter is a semiconductor interface device that converts parallel digital data into low-voltage differential signals. Differential signaling represents each bit with two complementary conductors, reducing sensitivity to common-mode noise and allowing reliable high-speed communication over board-level interconnects. In the broader hierarchy, the DS90C363MTDX belongs to the LVDS transmitter class, flat-panel display interface family, interface IC category, and semiconductor product category. The key features of this device include an 18-bit programmable data width, a 65 MHz operating specification, a 3.3 V supply, and FPD-Link operation. These characteristics allow the transmitter to carry display pixel data while reducing the number of interconnects required by conventional single-ended parallel signaling. Its 48-terminal TSSOP package also provides a compact surface-mount implementation for display-controller and interface boards. The transmitter is designed for parallel-to-differential conversion in flat-panel display systems. Its architecture accepts digital pixel information and serializes it onto an LVDS link, while the receiver and display timing system recover the transmitted data at the opposite end. The reported 1,300 Mbps data rate corresponds to the high-speed serialized link capability, whereas the 18-bit input width describes the parallel pixel payload presented to the transmitter. Typical uses include digital flat-panel monitors, industrial display controllers, automotive display interfaces, medical display equipment, video-processing systems, and embedded graphics platforms. It is particularly appropriate when a system requires an LVDS FPD-Link transmitter rather than a generic low-speed differential driver, and when the source device must transfer an 18-bit pixel bus into a compact high-speed differential channel. The primary layout consideration is placement of the transmitter close to the LVDS output connector and the source graphics logic. Keep the differential pair routed as a controlled-impedance pair, minimize stub lengths, and follow the manufacturer's pin-description and reference-layout guidance. Confirm output timing, receiver compatibility, connector pin assignment, and panel-specific initialization requirements before releasing a production design. This product record combines manufacturer identification, package and interface specifications, sourcing guidance, application fit, and a constrained drop-in comparison. It also highlights the important distinction between the 18-bit parallel payload, the 65 MHz operating point, and the 1,300 Mbps serialized LVDS link so engineers can evaluate bandwidth, board constraints, and receiver interoperability consistently.

RFQ پەیوەندی
DS90C365AMT - 3.3V 18-Bit LVDS FPD Transmitter | TI
DS90C365AMT

DS90C365AMT - 3.3V 18-Bit LVDS FPD Transmitter | TI

The Texas Instruments DS90C365AMT is a +3.3 V programmable 18-bit Flat Panel Display Link transmitter that converts 21 bits of LVCMOS/LVTTL data into four LVDS differential data streams. It supports a 3 V to 3.6 V supply, an 87.5 MHz pixel clock, an aggregate data rate of 1.785 Gbps, and a 48-TSSOP package. The interface is designed for high-speed point-to-point connections between display timing controllers and LVDS panel receivers. A Flat Panel Display Link transmitter is a display-interface IC that converts parallel logic signals into low-voltage differential signaling. This conversion reduces signal amplitude, supports clock-rate multiplication, and carries pixel and control data across a compact differential link. The DS90C365A family belongs to the broader category of display serializers and interface transceivers, placing it within the semiconductor and display-interface hierarchy. The DS90C365AMT accepts 18-bit display data together with associated control and clock information and serializes the information into four LVDS lanes. Its programmable operation supports link configuration across different display architectures. The 87.5 MHz link frequency and 1.785 Gbps data capability make the device applicable to flat-panel displays, industrial LCD panels, digital signage, and other multi-pixel parallel-to-LVDS interfaces. The DS90C365A incorporates a phase-locked loop that supports the high-speed serialization function. Because this is a transmitter-only device, it requires a compatible LVDS receiver at the other end of the link. The 48-TSSOP package provides 48 external terminals and is suitable for conventional surface-mount PCB assembly. Tube packaging is identified for the DS90C365AMT ordering variant in distributor search data. Typical implementations connect a display timing controller or graphics source to an LVDS display panel. The transmitter accepts parallel pixels and control signals, then sends four differential lanes carrying serialized data and embedded clock information. The receiver determines the supported display timing and must be electrically compatible with the transmitter output. This arrangement is useful where a compact LVDS interface is required instead of a direct parallel interface across the full board or cable distance. Designers should verify LVDS trace impedance, differential pair geometry, connector or panel requirements, receiver compatibility, and the power-supply decoupling network against the manufacturer datasheet. The stated 3 V to 3.6 V operating supply leaves little tolerance for supply overshoot, so routing and load behavior must be controlled. Pin assignments and unused-terminal details should be taken directly from the manufacturer documentation before PCB routing. This page consolidates the verified manufacturer and distributor information for DS90C365AMT, identifies documented pin-compatible family replacements, and provides application guidance, comparison criteria, and design considerations. It also distinguishes verified performance figures from parameters that require confirmation from the complete manufacturer datasheet.

RFQ پەیوەندی
DS90C365AMTX - 87.5MHz 18-Bit LVDS Transmitter | TI
DS90C365AMTX

DS90C365AMTX - 87.5MHz 18-Bit LVDS Transmitter | TI

The Texas Instruments DS90C365AMTX is a +3.3 V programmable LVDS transmitter for an 18-bit Flat Panel Display link, operating at up to 87.5 MHz with four LVDS data streams in a 48-pin TSSOP package. The device provides the high-speed differential signaling required to transfer pixel data between a display controller and panel interface while accepting LVCMOS or LVTTL source signals. An LVDS transmitter is a high-speed interface IC that converts parallel logic data into low-voltage differential pairs. LVDS belongs to the broader interface-IC hierarchy and supports reliable point-to-point links over longer PCB or cable distances than ordinary single-ended CMOS because its differential signaling improves noise immunity. In a Flat Panel Display Link, the transmitter serializes parallel display data into four differential channels that are paired with a suitable LVDS receiver at the display endpoint. The DS90C365A family supports an 87.5 MHz link and provides programmable operation for display-panel interface requirements. Its +3.3 V supply operation, four LVDS outputs and 21-bit internal input conversion support an 18-bit Flat Panel Display payload with associated clock and control signaling. The device also supports flexible data and clock arrangements, helping panel designers adapt one controller design to different display timing and interface conventions. The DS90C365A is a pin-to-pin replacement for DS90C363, DS90C363A and DS90C365 according to Texas Instruments. It includes improvements intended for display links while avoiding the no-EN pin of earlier devices. No special startup sequence is required between the clock, data and power-down inputs, allowing source signals to be applied before or after device power-up. That characteristic simplifies system sequencing and reduces controller reset complexity. Typical applications include flat-panel LCD monitors, industrial panel displays, medical-display controllers, automotive navigation displays, digital signage and other LVDS display interfaces. The transmitter is most appropriate when a host processor or display controller must serialize parallel pixel data into compact differential channels without relying on a higher-voltage source-synchronous interface. The primary design considerations are LVDS trace impedance, connector and cable compatibility, receiver selection, panel timing and power sequencing. The data and clock inputs must be driven by CMOS-compatible logic, while the four differential outputs require matched routing and the receiver or panel input must support the corresponding data and clock channel arrangement. Use the Texas Instruments datasheet pin-description and typical-application tables to assign every signal. This product page organizes the DS90C365AMTX specifications, verified sourcing information, pin-compatible family alternatives, application guidance and design notes into one engineering reference. It also distinguishes confirmed manufacturer characteristics from parameters that require verification against the latest device documentation before a board is released for production.

RFQ پەیوەندی
DS90C365MTD - 85MHz FPD-Link LVDS Transmitter | Texas Instruments
DS90C365MTD

DS90C365MTD - 85MHz FPD-Link LVDS Transmitter | Texas Instruments

The National Semiconductor DS90C365MTD is a 3.3 V programmable LVDS transmitter for 18-bit or 24-bit Flat Panel Display (FPD) Link-85 interfaces, with one LVDS driver, an operating supply range of 3 V to 3.6 V, and a 48-lead TSSOP package. It supports data throughput up to 2.38 Gbps and reduces external LVDS bus size and system cost through narrow-bus transmission. An LVDS transmitter is a high-speed differential interface driver that converts low-voltage CMOS/TTL logic into a low-EMI differential signal. LVDS belongs to the differential line-driver family and the broader interface-IC hierarchy, providing a practical alternative to parallel bus links when cable distance, signal count, EMI control, or data rate makes parallel routing impractical. The device's principal features include a 345 mV typical LVDS output swing, operation from a single 3 V to 3.6 V supply, and an internal PLL that requires no external components. The source also identifies compatibility with the TIA/EIA-644 LVDS standard. These characteristics make the transmitter useful where high data throughput must be transferred through a reduced-size differential link. The programmable architecture supports both 18-bit and 24-bit FPD-Link configurations while operating as a transmitter rather than a bidirectional transceiver. Its differential output is intended to reduce conducted emissions and radiated EMI by limiting common-mode voltage excursions. The internal PLL simplifies implementation compared with transmitter designs that require external loop-filter components. Typical uses include flat-panel display links, digital video interfaces, industrial display controllers, and embedded display systems that transmit wide parallel data over a compact cable. In a practical design, the parallel data enters the transmitter, the internal serializer converts it into a high-speed differential stream, and a matched LVDS receiver reconstructs the data at the display endpoint. Designers should use controlled-impedance differential routing, maintain the receiver and transmitter ground reference appropriately, and verify connector and cable compatibility with the LVDS standard. Supply decoupling should be placed close to the device, while signal-integrity evaluation should include the complete transmitter-to-receiver channel rather than relying only on simulation of the IC. This page combines verified distributor information, interface specifications, application guidance, and drop-in replacement analysis. It distinguishes electrically similar interface ICs from true pin-compatible alternatives and highlights where a PCB redesign is still required.

RFQ پەیوەندی
DS90C365MTDX - 85MHz LVDS FPD-Link Driver | TI
DS90C365MTDX

DS90C365MTDX - 85MHz LVDS FPD-Link Driver | TI

The Texas Instruments DS90C365MTDX is a +3.3 V programmable LVDS transmitter for Flat Panel Display (FPD) Link interfaces, operating at up to 85 MHz and providing an 18-bit data channel in a 48-pin TSSOP package. It is designed for point-to-point digital video links where low-voltage differential signaling is required to transfer display-related data reliably over a cable or PCB trace. An LVDS transmitter is an interface IC that converts low-voltage digital data into a differential physical-layer signal. FPD-Link is a display-interface hierarchy in which parallel or encoded display data is transported over a low-voltage differential connection. Compared with single-ended drivers, LVDS uses complementary differential outputs to improve noise immunity, reduce sensitivity to common-mode noise, and support longer or higher-quality interconnects when implemented with appropriate termination and layout. The DS90C365 supports a 3.3 V supply and 85 MHz signaling. The device family also includes DS90C385 and DS90C363 products, providing options for different channel-width and link requirements within the same FPD-Link application area. The DS90C365MTDX is identified as a one-driver FPD-Link LVDS device, while the 48-pin TSSOP package supports dense display-interface assemblies. The transmitter is positioned for digital flat-panel displays, monitor backplanes, industrial display controllers, video timing conversion, and other systems that transmit display data between a controller and a panel. Its differential output architecture is especially useful where the cable or trace length makes common-mode noise rejection and signal integrity important. For implementation, use the manufacturer's pin-description table when assigning signals and observe the recommended termination and decoupling arrangement. PCB routing should keep differential traces closely coupled, use controlled impedance, minimize stubs, and provide a continuous return path. Verify input timing, output mapping, supply sequencing, and panel-specific connector requirements before releasing a production layout. This page consolidates the verified device identity, package information, interface characteristics, sourcing parameters, and application guidance into an engineering-oriented reference. It also identifies same-family drop-in candidates for design review, while clearly separating confirmed attributes from parameters that still require confirmation against the manufacturer datasheet.

RFQ پەیوەندی
DS90C383MTD - 3.3V 24-Bit LVDS FPD-Link Transmitter | Texas Instruments
DS90C383MTD

DS90C383MTD - 3.3V 24-Bit LVDS FPD-Link Transmitter | Texas Instruments

The Texas Instruments DS90C383MTD is a 3.3 V programmable LVDS transmitter for 24-bit flat-panel display links, operating to 65 MHz and supplied in a 56-pin TSSOP package. The device is designed for point-to-point FPD-Link transmission between graphics engines and flat-panel display timing controllers, with programmable transmitter output, selectable strobe timing, and a single 3.3 V supply. According to the verified TI product and datasheet results, the DS90C383 family supports 20 MHz to 65 MHz shift-clock operation and is intended for XGA, SXGA, and related digital display interfaces. An LVDS FPD-Link transmitter is a specialized interface IC that converts low-voltage digital pixel data into a differential, low-voltage signaling stream suitable for reliable transfer over a cable or PCB trace. Its role in the display hierarchy is serializer interface: graphics data and synchronization signals enter the device, and differential LVDS outputs leave toward a receiver or display timing controller. This reduces signal count compared with parallel display signaling and helps support longer interconnects with low electromagnetic interference. The verified TI description identifies the DS90C383 as a 3.3 V programmable LVDS transmitter with a 24-bit FPD-Link and a 65 MHz maximum clock. The manufacturer datasheet search result also identifies DS90C383MTD as the 56-pin TSSOP ordering option and references DS90C383SLC as a separate ordering option. The device is associated with a chipset approach that pairs the transmitter with a compatible LVDS receiver. Reported feature material identifies programmable transmitter operation, selectable rising- or falling-edge strobe behavior, single-pixel-per-clock operation, XGA-ready support, and low-power-down consumption, although several detailed electrical limits are not included in the supplied verification text. The primary engineering role of the DS90C383MTD is therefore to serialize a parallel 24-bit display stream onto a small number of differential LVDS lanes while preserving clocking and data arrangement for a remote display receiver. Its 65 MHz capability corresponds to the maximum pixel-clock performance stated by TI and makes it appropriate for established small-panel and industrial display systems rather than current high-resolution high-refresh display links. Typical deployments include XGA-compatible flat-panel monitors, industrial HMI panels, embedded control displays, test equipment, and instrumentation. The transmitter should be paired with a receiver that supports the same FPD-Link data rate, lane count, clock polarity, and synchronization scheme. Designers must also verify connector and cable impedance, AC coupling where required by the link implementation, trace length matching, and the receiver's input capability. The key design consideration is that 65 MHz is the stated upper clock range, not a universal guarantee for every panel timing combination. Pixel-clock rate, blanking intervals, lane count, electrical loading, and receiver tolerance determine whether a particular display timing is supported. This page synthesizes the verified manufacturer and distributor information, identifies the practical replacement constraints, and separates documented facts from parameters that still require confirmation from the full manufacturer datasheet.

RFQ پەیوەندی
DS90C383MTDX - 65MHz Programmable LVDS Transmitter | TI
DS90C383MTDX

DS90C383MTDX - 65MHz Programmable LVDS Transmitter | TI

The Texas Instruments DS90C383MTDX is a 3.3 V programmable LVDS transmitter for 24-bit flat-panel display links, operating up to 65 MHz and packaged in a 56-pin TSSOP. The device converts 28 bits of LVCMOS/LVTTL data into four LVDS data streams and conveys a phase-locked transmit clock over a fifth LVDS link. Its supported data rate is 227 Mbps. A flat-panel display link, or FPD-Link, is a high-speed serial interface that transfers parallel pixel data and timing information between a graphics controller and a display. LVDS, or Low Voltage Differential Signaling, uses low-amplitude differential signals to support reliable point-to-point data transfer while limiting voltage noise and electromagnetic interference. The DS90C383MTDX belongs to the broader interface IC and display-interface hierarchy. The transmitter includes programmable rising-edge or falling-edge data strobe operation, allowing it to work with different graphics-controller timing. A rising-edge implementation can interoperate with the falling-edge DS90CF384 receiver without translation logic. The dedicated configuration pin provides a convenient way to align the transmitter's output strobe with the receiving system and simplifies adaptation between source and display timing conventions. The DS90C383 family pairs the DS90C383 transmitter with the DS90CF384 receiver for a complete LVDS display link. The transmit path preserves parallel pixel information as four differential data channels while adding a separate differential clock channel. This organization supports compact interconnects between display-controller boards and large-panel assemblies while reducing the number of single-ended signals routed over cables or board-to-board interfaces. Typical uses include digital flat-panel monitor links, industrial display controllers, automotive display systems, point-of-sale terminals, and other LVDS-equipped visual systems. The 24-bit color payload and 65 MHz operating capability suit parallel RGB pixel streams that must be serialized before reaching a panel interface. System designers still need to verify source timing, receiver polarity, connector routing, and cable-length limitations against the device electrical requirements. For layout, place the transmitter close to the LVDS output connector and route the five differential links as tightly coupled pairs on a continuous reference plane. Keep LVDS traces away from switching nodes and maintain a solid ground reference beneath the links. The graphics-controller interface also requires careful clock and data timing review because programmable strobe polarity changes when data is captured relative to the transmitted clock. This page combines the manufacturer's interface description, 227 Mbps and 65 MHz operating information, package details, pin-compatible alternatives, and practical link-design guidance. It also distinguishes the transmitter from the related DS90CF384 receiver and identifies which parameters require confirmation before substitution or production release.

RFQ پەیوەندی
DS90C383SLC - 3.3V 24-Bit 65MHz LVDS Transmitter | TI
DS90C383SLC

DS90C383SLC - 3.3V 24-Bit 65MHz LVDS Transmitter | TI

Texas Instruments DS90C383SLC is a 3.3-V programmable 24-bit flat-panel-display link transmitter operating up to 65 MHz and packaged in a 64-ball SLC64A BGA. It converts parallel 24-bit display data into low-voltage differential signaling for a corresponding LVDS receiver. The verified manufacturer description identifies the device as the DS90C383, while the DS90C383SLC ordering code specifies the SLC64A package. An LVDS transmitter is a display-interface device that transmits data across a balanced differential link using low-voltage signaling. The technology hierarchy is LVDS transmitter to differential line driver, display interface IC, interface IC, and semiconductor. FPD-Link systems commonly pair such a transmitter with an LVDS receiver at the far end of a cable or PCB trace, reducing signal-integrity and common-mode-noise problems compared with single-ended parallel transmission. The principal verified characteristics are a 3.3-V supply, programmable operation, a 24-bit parallel data interface, and a 65-MHz maximum link clock. According to the manufacturer product page, these features position the DS90C383 for flat-panel-display links where serialized differential transport is needed. Its broad parallel input bus supports multiple display pixels or source-synchronous interface signals while reducing the number of signal conductors required between the transmitter and receiver. The DS90C383SLC uses the TI FPD-Link approach to move display information from a graphics source to a panel receiver. The differential output helps reject common-mode noise, while serialized data reduces skew exposure across many parallel conductors. Programmable transmitter configuration provides the system designer with control over the link behavior. Exact output voltage, termination, current, and timing limits require confirmation in the manufacturer datasheet because they are not included in the supplied web results. Typical uses include small-format LCD panels, industrial human-machine-interface displays, test equipment, and other embedded systems that pair a graphics engine with an LVDS-capable display receiver. In these systems, the transmitter commonly accepts parallel pixel data and clock signals, then drives a shielded cable or controlled-length board interconnect. The receiver reconstructs the data for the panel timing controller. The principal design consideration is that this is a high-speed differential interface, so trace geometry, connector return paths, input timing, and cable termination must follow the datasheet reference layout. Designers should also verify the exact SLC64A land pattern, supply decoupling requirements, and receiver interoperability before layout release because those details are unavailable in the supplied search snippets. This page combines the verified 3.3-V, 24-bit, and 65-MHz device identity with current distributor pricing, manufacturer documentation links, and same-brand drop-in replacement guidance. The comparison and design guidance are intended to reduce board-rework risk while keeping every proposed replacement in the same SLC64A package family.

RFQ پەیوەندی
DS90C385AMTX - 87.5MHz 24-Bit LVDS Transmitter | Texas Instruments
DS90C385AMTX

DS90C385AMTX - 87.5MHz 24-Bit LVDS Transmitter | Texas Instruments

The Texas Instruments DS90C385AMTX is a programmable 3.3 V flat-panel-display LVDS transmitter designed for 24-bit RGB interfaces. It samples 28 LVCMOS/LVTTL input bits and serializes them into four differential LVDS data streams, plus a fifth differential stream carrying the phase-locked transmit clock. Its 56-pin TSSOP package supports an 87.5 MHz transmit clock and 2450 Mbps aggregate signaling capability. An LVDS transmitter is a high-speed interface device that converts low-voltage complementary logic into low-voltage differential signaling. LVDS belongs to the differential data-interface hierarchy and helps reduce electromagnetic interference while enabling reliable point-to-point links over balanced conductors. In an FPD Link system, the DS90C385AMTX is the transmitter-side device between parallel pixel or control logic and an LVDS-capable display receiver. The device accepts 28 parallel bits per transmitted clock cycle. At 87.5 MHz, those inputs can carry 24 RGB data bits and three control bits. A separate fifth LVDS link transports the phase-locked transmit clock, allowing the receiver to recover a low-skew sampling reference. The manufacturer describes the DS90C385A family as supporting reduced EMI, a narrower interface bus, and spread-spectrum clocking. Programmability is a major architectural feature because transmit characteristics can be adjusted through the device's configuration interface rather than relying on entirely fixed outputs. The 3.3 V supply architecture simplifies integration with contemporary CMOS display controllers, while differential outputs support noise-tolerant board and cable connections. The fifth clock link also separates the forwarded clock from the four serialized data pairs, reducing receiver-side clock-recovery complexity. Typical uses include LCD flat-panel display links, industrial panel interfaces, high-resolution monitor connections, embedded display systems, and other LVDS panels requiring a parallel-to-differential bridge. The 87.5 MHz operating point is especially relevant to 24-bit color display data, where video timing, control metadata, and low-power differential signaling are combined in a compact interface. PCB design must preserve controlled-impedance differential routing and keep the clock and data pairs length-matched within system requirements. Place decoupling capacitors close to the supply pins, route outputs as short balanced pairs, and avoid unnecessary stubs. Because this is a high-speed interface rather than a power device, thermal analysis is less critical than signal-integrity and layout discipline. This page combines the manufacturer's functional description with package, interface, application, replacement, and design guidance. It also distinguishes direct pin-compatible family replacements from lower-voltage or otherwise different interface devices so engineers can evaluate board-level compatibility before committing to a substitution.

RFQ پەیوەندی
DS90C385MTD - 85MHz Programmable LVDS Transmitter | Texas Instruments
DS90C385MTD

DS90C385MTD - 85MHz Programmable LVDS Transmitter | Texas Instruments

Texas Instruments DS90C385MTD is a +3.3 V programmable LVDS transmitter designed for 24-bit flat panel display links operating at 85 MHz. The device converts parallel LVCMOS or LVTTL data into differential LVDS signals and is supplied in a 56-pin TSSOP package. Its 28-bit parallel input path and four LVDS data outputs support high-speed point-to-point display and video signaling. An LVDS transmitter is a physical-layer interface IC that converts low-voltage digital logic into a balanced differential signal. The differential architecture is commonly used to transport data reliably over cable or PCB traces while limiting electromagnetic interference, reducing sensitivity to ground noise, and enabling higher data rates than ordinary single-ended logic. Within the interface hierarchy, this device is an LVDS line driver and serializer for display links. The DS90C385MTD is associated with an 85 MHz FPD-Link interface, a +3.3 V supply, programmable operation, and a 56-pin TSSOP package. The verified distributor records describe it as a four-driver LVDS transmitter for flat panel display links. Its parallel-to-differential conversion function makes it suitable for carrying compact digital video or control data between a graphics controller and a display or another LVDS endpoint. This family also appears under the DS90C365 description, which identifies the device as an 18-bit or 24-bit FPD-Link transmitter operating at 85 MHz. Different DS90C365 and DS90C385 family members can differ in supported data width, enable controls, and implementation details, so engineers must confirm the exact pin configuration and electrical limits against the manufacturer datasheet before substituting a related MPN. Typical applications include digital flat-panel display interfaces, industrial monitor links, video timing and control paths, and other point-to-point systems where LVCMOS logic must be converted to differential LVDS. The 56-pin TSSOP package provides enough pins for dedicated differential data, clock, control, configuration, and power connections while supporting standard board-level assembly. A successful implementation requires careful review of supply voltage, input and output levels, pin functions, termination, trace geometry, and decoupling. Differential pairs should be routed with controlled spacing and matched length, while power and ground connections should be kept quiet. The verified search results do not provide a public pin table or detailed electrical limits, so those values must be confirmed in the manufacturer datasheet before layout or production use. This product record combines verified distributor metadata, package and application context, available replacement information, and practical selection guidance. It also distinguishes documented facts from parameters that still require datasheet confirmation, helping engineers evaluate the DS90C385MTD without relying on unverified assumptions.

RFQ پەیوەندی
DS90C385MTDX - 85 MHz LVDS FPD-Link Transmitter | Texas Instruments
DS90C385MTDX

DS90C385MTDX - 85 MHz LVDS FPD-Link Transmitter | Texas Instruments

The Texas Instruments DS90C385MTDX is a 3.3 V programmable LVDS transmitter for Flat Panel Display (FPD) Link interfaces, operating at up to 85 MHz and packaged in a TSSOP package. The device converts parallel LVCMOS/LVTTL display data into differential LVDS signals for reliable point-to-point panel connections. Its intended application is high-speed digital video and control transport between a display controller and a flat-panel display. An LVDS FPD-Link transmitter is a mixed-signal interface IC that belongs to the broader low-voltage differential signaling and display-interface hierarchy. FPD-Link carries parallel pixel data over a low-voltage differential link, while LVDS provides common-mode noise rejection and low electromagnetic emissions. The DS90C385MTDX therefore occupies the transmitter stage between a parallel display controller and a differential panel interface. Key features include 3.3 V operation, programmable LVDS output characteristics, and support for flat-panel display links operating at 85 MHz. The transmitter accepts 28 bits of LVCMOS/LVTTL data according to the family description, with the exact data mapping and configurable payload structure defined by the manufacturer datasheet. Differential signaling reduces the voltage swing required for high-speed transfer compared with single-ended parallel signaling. The device architecture combines parallel CMOS inputs with a programmable differential output stage. Its primary design benefit is low-voltage data transmission, which helps control signal amplitude and supports cleaner interconnections between display timing controller circuitry and remote panel electronics. Users should preserve the recommended input and output termination, supply decoupling, and controlled-impedance routing used by the manufacturer reference design. Typical uses include LCD and other flat-panel display interfaces, digital signage controllers, industrial human-machine-interface panels, medical displays, and embedded display subsystems requiring a scalable differential link. The same transmitter can serve both compact embedded panels and larger display assemblies when the selected panel interface and cable length satisfy the link budget. The principal design consideration is signal integrity. Route each differential pair as a tightly coupled pair with continuous reference planes, avoid stubs, match propagation distance between lanes, and place termination exactly where the reference design specifies it. Verify power sequencing and output enable behavior in the system power architecture. This page combines the exact catalog identity, package and interface facts, strict drop-in comparison data, and practical display-link design guidance. It helps engineers identify valid replacement options and plan layout, power, and signal-integrity requirements before releasing a flat-panel interface PCB.

RFQ پەیوەندی
DS90C387VJD - 48-Bit Dual-Pixel LVDS Transmitter | TI
DS90C387VJD

DS90C387VJD - 48-Bit Dual-Pixel LVDS Transmitter | TI

Texas Instruments DS90C387VJD is a +3.3 V dual-pixel LVDS display interface transmitter that converts 48 bits of CMOS/TTL pixel data into eight LVDS data streams for host-to-flat-panel display links supporting up to QXGA resolution. It is supplied in a 100-pin TQFP (NEZ) package measuring 14 x 14 mm. The device is an 8-channel driver with no integrated receiver channels. A dual-pixel LVDS display interface is a high-speed display-link interface in which two pixels are transmitted in parallel over multiple low-voltage differential signaling lanes. LVDS belongs to the differential-interface hierarchy used to move high-speed pixel data reliably between a display controller or graphics source and a flat-panel display. Reducing the number of transmitted signal lines helps shorten PCB routing while preserving high aggregate data throughput. The DS90C387VJD accepts 48 bits representing dual 24-bit pixel data and converts them into eight differential LVDS streams. During blanking periods, it also sends control information including VSYNC, HSYNC, DE, and two user-defined signals. These functions allow synchronization and control traffic to share the physical link instead of requiring a separate interface for every control function. The verified manufacturer information identifies the part as a dual-pixel transmitter for SVGA and QXGA display systems. It operates from a +3.3 V supply and is packaged in a surface-mount 100-pin TQFP configuration. The part-details listing carries the NEZ lifecycle designation, while the supplied data gives an operating-temperature range of -10 °C to +70 °C. Detailed electrical limits, LVDS output voltage, propagation delay, pixel-clock range, and pin-level signal definitions were not included in the supplied records and therefore are not inferred here. Typical display applications include desktop flat-panel monitors, industrial panel interfaces, and embedded display systems that use the DS90C387/DS90CF388 transmitter-receiver pairing. In these systems, the DS90C387VJD handles parallel CMOS/TTL pixel input and low-voltage differential output, while a compatible receiver at the panel converts the differential data back into logic-level signals. The primary design consideration is PCB signal integrity. Eight LVDS data outputs require controlled impedance routing, minimized stubs, appropriate layer transitions, and placement of receiver termination close to the receiving device. The 100-pin package also requires adequate via-in-pad or through-hole fanout under fine-pitch leads, along with deliberate grounding and supply-decoupling layout. This page combines the verified Texas Instruments product description, package and lifecycle information, distributor identification, and cross-reference results. It also distinguishes documented order variants from genuinely supported drop-in alternatives and highlights the electrical and lifecycle values that still require confirmation from the complete manufacturer datasheet.

RFQ پەیوەندی
DS90C401M - Dual LVDS Driver | Texas Instruments
DS90C401M

DS90C401M - Dual LVDS Driver | Texas Instruments

The Texas Instruments DS90C401M is a dual low-voltage differential-signaling (LVDS) driver optimized for high-data-rate, low-power point-to-point links. The verified source data identifies two differential driver outputs, current-mode operation, minimized short-circuit fault current, low EMI from output swings typically near 340 mV, and an 8-lead small-outline package. It is intended to pair with a DS90C402 receiver to form a complete dual high-speed interface solution. An LVDS driver is a differential-signaling interface IC that transmits information through two conductors carrying complementary signals. The small voltage swing reduces electromagnetic emissions while the differential receiver detects the voltage difference between the conductors. In the broader hierarchy, an LVDS driver belongs to the line-driver and interface-IC category and supports balanced, high-speed communication over printed-circuit-board traces and other suitable point-to-point interconnects. The DS90C401M is specifically described as a dual device for high-data-rate and low-power applications. Its current-mode architecture helps keep power dissipation low even at high frequency and limits fault current during short-circuit conditions. These characteristics are important where data throughput must be maintained without allowing interface noise, excessive power, or fault energy to disrupt the linked circuitry. The manufacturer also presents the DS90C401 and DS90C402 as a complementary chip solution. Typical communication links can place the DS90C401M at the transmitting end and a suitable DS90C402 receiver at the receiving end. Differential routing should preserve the conductor geometry and provide a continuous return path beneath or alongside the pair. Because LVDS performance depends on the complete transmission system, cable length, termination, connector geometry, trace impedance, and receiver characteristics must be evaluated together rather than treating the IC in isolation. A key design consideration is maintaining a low-noise power and ground environment. Decoupling capacitors should be positioned close to the supply and ground pins, while differential traces should be routed as a balanced pair with consistent spacing and minimal stubs. The 8-lead package is suitable for conventional surface-mount assembly, but pin assignments, exposed thermal requirements, and process details should be confirmed from the manufacturer datasheet before layout release. This page consolidates verified manufacturer descriptions, distributor links, and the identified complementary-interface relationship. It also distinguishes confirmed facts from parameters not supplied by the verified data, avoiding unsupported claims while providing an engineering starting point for DS90C401M selection, sourcing, and circuit design.

RFQ پەیوەندی
DS90C401M-TI - Dual LVDS Driver | Texas Instruments
DS90C401M-TI

DS90C401M-TI - Dual LVDS Driver | Texas Instruments

The Texas Instruments DS90C401M-TI is a dual Low Voltage Differential Signaling driver optimized for high-data-rate, low-power point-to-point interfaces, and it is supplied in an 8-pin SOIC package. The device provides two driver channels and uses current-mode operation to maintain low power dissipation at high signaling frequencies while minimizing short-circuit fault current. A low-voltage differential-signaling driver is a line-driver IC that converts a low-voltage logic signal into a balanced differential output. Differential signaling rejects common-mode noise and reduces radiated emissions when the receiver, connector, and transmission-line geometry are handled correctly. In the broader semiconductor hierarchy, an LVDS driver is a physical-layer interface IC within the broader interface-controller category. The verified manufacturer information identifies the DS90C401 as a dual driver designed for high-data-rate and low-power applications. Its two output channels can work with the DS90C402 receiver to create a complete dual-channel point-to-point LVDS link. The current-mode architecture is significant because it helps limit dissipation as data activity and frequency increase, while the controlled short-circuit behavior helps protect the driver during output faults. The DS90C401M part is identified by distributor listings as a 2-channel, 2/0 LVDS driver in an 8-SOIC package. The SOIC construction provides a compact surface-mount option for point-to-point links and makes the device suitable for PCB designs that require a conventional small-outline package. Exact voltage, data-rate, differential-output, supply-current, and temperature limits must be confirmed from the manufacturer datasheet before a production design is released. Typical uses include dual-channel high-speed backplanes, cabinet links, video or control transport between circuit boards, clock distribution, and industrial data acquisition systems. In each case, the device is most useful where two channels can be routed to a compatible DS90C402 receiver and where cable length, connector geometry, and signal-integrity rules are controlled. A practical design consideration is to treat the differential pair as a controlled-impedance transmission line rather than two independent wires. Keep the two traces closely coupled, provide the receiver termination specified by the manufacturer, minimize stub branches, and confirm the data rate and cable length against the published AC and DC operating limits. This page distinguishes verified product facts from parameters that still require datasheet confirmation. The information gain here is the combination of verified sourcing links, an honest package and interface classification, drop-in candidate analysis, and design guidance centered on current-mode LVDS behavior. It is intended to help engineers narrow the correct TI device and datasheet review without inventing unavailable electrical ratings or commercial data.

RFQ پەیوەندی
DS90C401MX - Dual LVDS Driver | Texas Instruments
DS90C401MX

DS90C401MX - Dual LVDS Driver | Texas Instruments

The Texas Instruments DS90C401MX is a dual Low Voltage Differential Signaling (LVDS) driver optimized for high-data-rate, low-power point-to-point interfaces, with two driver channels in an 8-pin SOIC package. According to the manufacturer datasheet, the device is designed to pair with the DS90C402 receiver, and its current-mode architecture helps maintain low power dissipation at high frequency while minimizing short-circuit fault current. An LVDS driver is a differential-signaling interface device that converts low-voltage logic inputs into balanced differential outputs. Its role within the interface hierarchy is important: LVDS belongs to differential digital interface ICs, which sit below high-speed interface transceivers and support reliable point-to-point data transfer over cables or PCB traces. Differential signaling improves noise immunity by comparing the voltage difference between two conductors rather than relying on a single conductor referenced to ground. The DS90C401MX provides a dual-driver arrangement for systems requiring two independent LVDS transmit channels. Its current-mode operation is specifically highlighted for high-data-rate operation, where the device is intended to limit power dissipation and short-circuit current. The companion DS90C402 receiver is identified by the manufacturer as the matching device in a complete dual high-speed point-to-point interface solution. The verified product information identifies the device as a dual LVDS driver in an 8-SOIC package. Detailed electrical limits, input thresholds, differential output voltage, propagation delay, maximum data rate, supply current, temperature range, and recommended decoupling values are not present in the supplied search excerpts. Those parameters should therefore be confirmed in the official Texas Instruments datasheet before final circuit design or production release. Typical applications include high-speed point-to-point links, industrial control connections, test and measurement equipment, communications equipment, and embedded systems that use LVDS physical signaling. The device can be paired with DS90C402MX-family receivers when the system architecture uses a transmitter and receiver across a balanced connection. Its dual-channel structure can reduce the number of driver packages required when two links share similar electrical and timing requirements. A key design consideration is to preserve the intended point-to-point topology and controlled-impedance routing between the driver and receiver. LVDS traces should be routed as a closely coupled differential pair, with the receiver and transmitter reference-design practices followed from the manufacturer documentation. Do not substitute electrical specifications from a similar interface IC without checking the full timing, voltage, supply, and fault-current requirements. This page synthesizes the verified manufacturer identity, package information, companion-interface relationship, and cross-reference findings for DS90C401MX. It distinguishes documented facts from unprovided technical values so engineers can identify the part efficiently without mistaking incomplete search excerpts for a complete datasheet specification.

RFQ پەیوەندی
DS90C401MX/NOPB - Dual LVDS Driver, 155.5 Mbps | Texas Instruments
DS90C401MX/NOPB

DS90C401MX/NOPB - Dual LVDS Driver, 155.5 Mbps | Texas Instruments

The Texas Instruments DS90C401MX/NOPB is a dual Low Voltage Differential Signaling (LVDS) driver optimized for high-data-rate, low-power point-to-point interfaces. The device provides two drivers, operates from a 4.5 V to 5.5 V supply, and supports data rates up to 155.5 Mbps. It is packaged in an 8-pin SOIC package identified as SOIC (D). The DS90C401 is designed to work with the DS90C402 receiver as a complete dual high-speed point-to-point interface solution. An LVDS driver is a differential signal-line transmitter that uses a balanced current-mode output stage. By steering current between two complementary outputs, the DS90C401 can transmit high-speed digital information while reducing common-mode noise and improving noise immunity over longer point-to-point interconnects. LVDS is part of the broader interface-IC hierarchy, which includes low-voltage differential signaling, differential line drivers, and high-speed serial interface devices. The current-mode architecture keeps power dissipation relatively low at high operating frequencies and limits the short-circuit fault current. These characteristics make the DS90C401MX/NOPB useful where data must be transferred reliably between circuit boards, rack-mounted equipment, test systems, or other short-reach high-speed links. The dual-driver configuration allows two LVDS channels to be implemented in one package, reducing component count when multiple links are required. The principal application is a dual point-to-point interface pairing the DS90C401 with one or more DS90C402 receivers. Each driver channel provides complementary differential outputs intended for a properly terminated LVDS transmission line. Designers should use controlled-impedance routing, maintain a continuous ground reference, place termination close to the receiver, and follow the manufacturer’s recommended decoupling and pinout guidance. The DS90C401MX/NOPB also offers a practical alternative to single-channel driver arrangements when two related high-speed links are needed. Its 4.5 V to 5.5 V operating range supports conventional 5 V interface systems, while the 155.5 Mbps data-rate capability addresses legacy and industrial data links. The /NOPB suffix identifies the lead-free, non-PB-free-package configuration as designated by Texas Instruments. This page combines the device’s core electrical and packaging characteristics with application guidance, comparison notes, and design considerations. It also identifies the exact DS90C401MX/NOPB manufacturer datasheet and product-page resources for authoritative electrical characteristics, recommended operating conditions, pin assignments, and application schematics.

RFQ پەیوەندی
DS90C402M - Dual LVDS Receiver, ±100 mV | Texas Instruments
DS90C402M

DS90C402M - Dual LVDS Receiver, ±100 mV | Texas Instruments

The Texas Instruments DS90C402M is a dual Low Voltage Differential Signaling receiver optimized for high-data-rate, low-power point-to-point interfaces, with two receivers, ±100 mV threshold sensitivity, common-mode noise protection, and an 8-lead SOIC package. It is designed to work with the DS90C401 as part of a dual high-speed interface solution. What is an LVDS receiver? Low Voltage Differential Signaling, or LVDS, is a differential digital interface technology that conveys one bit across two conductors carrying complementary signals. An LVDS receiver detects the voltage difference between those inputs and rejects common-mode noise that appears equally on both conductors. In the broader hierarchy, the DS90C402M is a differential line receiver, interface IC, digital communications component, and semiconductor. The main verified features are its dual-receiver architecture, ±100 mV input threshold sensitivity, and common-mode noise protection. The device is packaged in a PCB space-saving 8-lead small-outline package identified by distributor listings as SOIC. The receiver is intended for high-data-rate and low-power applications, making it suitable for point-to-point links where low voltage, differential signaling, and noise immunity are important. The DS90C401 and DS90C402 form a complementary pair-chip solution for dual high-speed point-to-point communication. Using matched differential routing helps preserve signal integrity and reduces susceptibility to external noise. The receiver’s threshold specification also defines the input signal region it recognizes as a valid differential transition, while common-mode protection helps the interface tolerate noise present on both input conductors. Typical applications include high-speed point-to-point links, low-voltage serial communication, LVDS-compatible backplanes, industrial control links, test equipment interfaces, and embedded systems that use differential digital signaling. The DS90C402M should be selected when the board uses the same eight-pin SOIC footprint and the interface electrical requirements match the verified receiver specifications. The datasheet should be consulted for supply voltage, input common-mode range, propagation delay, and absolute maximum ratings before final design release. For PCB implementation, keep the differential pair impedance controlled and minimize stubs and unnecessary routing length. Provide a continuous reference plane and terminate unused inputs according to the manufacturer’s guidance. Avoid substituting generic differential receivers without checking pin mapping, supply voltage, threshold behavior, and propagation delay. This page consolidates the verified manufacturer and distributor information, distinguishes documented facts from missing data, and provides application and design guidance beyond a basic distributor listing.

RFQ پەیوەندی
DS90C402M/NOPB Dual LVDS Receiver | Texas Instruments
DS90C402M/NOPB

DS90C402M/NOPB Dual LVDS Receiver | Texas Instruments

The Texas Instruments DS90C402M/NOPB is a dual low-voltage differential-signaling receiver designed for high-data-rate, point-to-point communication links. The device operates from a 4.5 V to 5.5 V supply, accepts two independent differential receiver channels, and is packaged in an 8-lead small-outline integrated-circuit package. Its receiver threshold sensitivity is ±100 mV, while common-mode noise protection helps reject interference present on the differential signal pair. The DS90C402M/NOPB is designed to work with the DS90C401 transmitter as a complete dual high-speed point-to-point interface solution. The 8-SOIC package provides a compact footprint for systems requiring multiple low-power differential links, including point-to-point serial data connections, industrial control links, test equipment, and embedded communication systems. The part is specified for a 1.5 ns receiver propagation delay and an operating temperature range of -40 °C to 85 °C. Its receiver architecture is intended to support reliable detection of small differential signals while rejecting common-mode noise. The device is supplied in a tube package according to the product information. Applications should account for the specified supply range, differential signal routing, input protection, controlled return paths, and the receiver’s sensitivity threshold. This page consolidates the manufacturer’s electrical information, package details, application guidance, and practical interface considerations for engineers evaluating the DS90C402M/NOPB.

RFQ پەیوەندی
DS90C402MX - Dual 155.5Mbps LVDS Receiver | Texas Instruments
DS90C402MX

DS90C402MX - Dual 155.5Mbps LVDS Receiver | Texas Instruments

The Texas Instruments DS90C402MX is a dual Low Voltage Differential Signaling receiver optimized for high-data-rate, low-power point-to-point links. It receives two differential data streams at up to 155.5 Mbps, provides ±100 mV receiver-threshold sensitivity, and includes common-mode noise protection. The device is packaged in an 8-lead small-outline package identified by the verified distributor data as an 8-SOIC configuration. An LVDS receiver is an interface IC that detects a small differential voltage between two conductors and converts that signal into a compatible digital logic output. This differential method belongs to the broader interface-IC and signal-conditioning hierarchy. Compared with single-ended links, differential reception can improve noise immunity by rejecting common-mode disturbance. The DS90C402MX is intended for one half of a dual high-speed link when paired with the Texas Instruments DS90C401. Key features include two independent LVDS receivers, operation to 155.5 Mbps, ±100 mV threshold sensitivity, and common-mode noise protection. Its low-power design targets systems where receiver power and board area are constrained. The dual architecture consolidates two receive channels into one package, reducing component count compared with two separate single-channel receivers. The exact supply current, input capacitance, propagation delay, output timing, and connector details are not present in the supplied verified data and therefore are not inferred here. The receiver’s differential inputs are intended for point-to-point communication, where a complementary transmitter establishes the proper signal and termination environment. Its common-mode protection is especially relevant when traces share a board with digital or switching circuitry. Engineers must nevertheless preserve the differential geometry recommended by the manufacturer datasheet and control impedance consistently from transmitter through receiver. A receiver alone does not create a compliant LVDS link; the transmitter, cable or PCB transmission medium, termination, connector, and system grounding all affect signal integrity. Typical applications include dual-channel point-to-point backplanes, industrial control links, embedded instrumentation, and compact communications equipment. The DS90C401/DS90C402 pairing supports two coordinated high-speed channels where a single-channel LVDS receiver would require duplicated packages. In data converters or digital processing systems, the receiver can also recover signals arriving from a remote circuit board when the board-level channel has already been characterized. The primary design consideration is preserving LVDS signal integrity through controlled-impedance, tightly coupled routing and correct termination. Review the complete manufacturer datasheet for electrical tables, recommended land patterns, input topology, and timing before release because several detailed values are unavailable in the verified excerpts. For pricing and replacement decisions, do not assume that a functional transceiver or driver is pin compatible; the receiver must match the existing footprint, supply arrangement, and pinout. This page combines the verified manufacturer descriptions, package identification, operating-rate reference, threshold sensitivity, and replacement search results into an engineering-oriented DS90C402MX overview. It distinguishes verified facts from parameters that require the full datasheet and avoids presenting unverified electrical, compliance, lifecycle, or pricing claims as established specifications.

RFQ پەیوەندی
DS90CF363AMTDX - 65MHz 21/3 LVDS FPD-Link Transceiver | TI
DS90CF363AMTDX

DS90CF363AMTDX - 65MHz 21/3 LVDS FPD-Link Transceiver | TI

The Texas Instruments DS90CF363AMTDX is a 21 transmitter and 3 receiver LVDS FPD-Link transceiver operating from a 3.0 V to 3.6 V supply and supporting a 65 MHz clock rate. The device is packaged in a 48-TSSOP and supplied tape and reel. Its parallel flat-panel display interface includes programmable LVDS outputs, an LVDS clock, and selectable data and clock output arrangements for display-panel drive applications. A flat-panel display link, or FPD-Link, is a high-speed parallel-to-serial interface used to transfer pixel data and synchronization signals between a graphics controller and a display panel. In the system hierarchy, an FPD-Link transceiver sits between an LCD or digital display interface and an LVDS panel connection, combining several parallel data channels onto fewer differential pairs. This reduces wiring density while preserving the bandwidth required for high-resolution display panels. The DS90CF363AMTDX provides 21 driver outputs and 3 receiver inputs in a single 48-TSSOP package. Its 3.0 V to 3.6 V operating supply supports 3.3 V display systems, while the 65 MHz operating specification supports pixel-clock rates commonly used with 18-bit flat-panel interfaces. The falling-edge LVDS transmitter architecture and selectable output configuration allow system designers to match panel timing and data-mapping requirements without changing the transceiver package. The device is intended for use in flat-panel display systems, LCD monitors, digital signage controllers, industrial panel interfaces, and embedded graphics systems. The 48-TSSOP outline provides a standard surface-mount footprint suitable for compact controller boards. Tape-and-reel packaging supports automated assembly and high-volume production, while the three receiver channels support clock and control feedback paths where the connected panel or interface requires them. Layout quality is critical in an LVDS link because differential trace mismatch, unequal pair lengths, and excessive stub lengths can degrade signal integrity at the 65 MHz operating rate. Route each LVDS differential pair as a tightly coupled pair over a continuous reference plane, avoid vias where possible, and place termination and interface components according to the manufacturer datasheet. Confirm that the selected panel connector and cable use the same data-channel mapping as the programmed transmitter configuration. This page consolidates the verified interface, supply, speed, package, and sourcing information for DS90CF363AMTDX with application guidance, same-family alternatives, and practical LVDS layout considerations that help shorten design-in and troubleshooting work.

RFQ پەیوەندی
DS90CF364AMTDX - 18-Bit 65MHz LVDS Receiver | Texas Instruments
DS90CF364AMTDX

DS90CF364AMTDX - 18-Bit 65MHz LVDS Receiver | Texas Instruments

The Texas Instruments DS90CF364AMTDX is a 3.3 V LVDS flat-panel-display receiver supporting an 18-bit data interface at up to 65 MHz in a 48-pin TSSOP package. It is designed for systems that transfer display-related data across a noise-resistant differential link. An LVDS receiver is an interface integrated circuit that converts low-voltage differential signaling into a logic-level digital signal. LVDS belongs to the broader differential-interface hierarchy and is commonly used where reliable data transfer, low electromagnetic interference, and scalable clock rates are important. The DS90CF364A family targets flat-panel-display links connecting a transmitter or display source to a receiver endpoint. The key operating characteristics are a 3.3 V supply, an 18-bit FPD link, and a maximum signaling frequency of 65 MHz. The 48-pin TSSOP package provides a conventional surface-mount footprint suitable for multilayer PCB designs. The operating-temperature range shown on the manufacturer part-details page is -10 °C to 70 °C, making the device appropriate for commercial and industrial equipment with controlled ambient conditions. The receiver architecture is intended to recover data from LVDS differential pairs and present compatible parallel digital signals to the connected display system. Its 65 MHz signaling rate establishes the timing envelope for the associated data lanes, while the 18-bit interface supports parallel display-related information. Designers must preserve controlled-impedance routing between the transmitter and receiver, maintain the required input termination, and observe the voltage and timing constraints defined by the manufacturer. Typical uses include flat-panel display controllers, industrial display equipment, video timing interfaces, monitor electronics, and embedded human-machine-interface systems. In these applications, the DS90CF364AMTDX can serve as the receiving endpoint for an LVDS FPD link, reducing susceptibility to common-mode noise when compared with a single-ended transfer path. PCB implementation should provide continuous ground planes, short differential traces, matched pair lengths, and proper LVDS input termination. The receiver should be placed according to the package and datasheet layout guidance, with supply decoupling and signal-return paths arranged to minimize switching noise. Component substitutions should be checked for identical pin functions, supply requirements, clock capability, and electrical timing rather than package name alone. This product page combines the manufacturer's ordering information, interface specifications, package details, drop-in replacement references, application guidance, and a parameter-by-parameter comparison. It is intended to help engineers identify the correct receiver and verify PCB, timing, thermal, and sourcing constraints before committing a design to production.

RFQ پەیوەندی
DS90CF364MTD - 65 MHz 18-Bit LVDS Receiver | Texas Instruments
DS90CF364MTD

DS90CF364MTD - 65 MHz 18-Bit LVDS Receiver | Texas Instruments

The Texas Instruments DS90CF364MTD is a 3.3 V LVDS receiver for an 18-bit flat-panel display link, operating at up to 65 MHz and supporting three LVDS data streams in a 48-TSSOP package. It converts differential LVDS data back into CMOS/TTL signals for display timing, control, and pixel-data recovery. The receiver is designed for high-speed panel interfaces where reducing cable size, connector count, and EMI susceptibility is important. An LVDS receiver is an interface-circuit component that restores low-voltage differential signaling into digital logic levels. In the broader hierarchy, it belongs to the LVDS interface family, then to serializers, deserializers, and interface ICs used in display and communications systems. LVDS transmits complementary signals over a balanced pair, allowing reliable data transfer across cables or PCB interconnects while limiting common-mode noise and radiated emissions. The DS90CF364MTD supports an 18-bit RGB data path with LCD timing and control signals, including FPLINE, FPFRAME, and DRDY. At a 65 MHz transmit-clock frequency, the link carries 455 Mbps per LVDS data channel according to the manufacturer product information. The receiver is intended to pair with the DS90C363 transmitter family, whose programmable rising- or falling-edge strobe operation allows interoperability with the falling-edge receiver. The device operates from a 3.3 V supply and is packaged in a surface-mount 48-TSSOP package. Its receiver architecture is designed for point-to-point display links, where the transmitter, receiver, cable, and connector form a controlled differential channel. The package and interface arrangement support compact display-controller boards while keeping the high-speed differential traces physically separate from sensitive analog and control circuitry. Typical applications include LCD and flat-panel monitor interfaces, digital signage, industrial HMIs, automotive display links, test equipment, and embedded video systems. In each case, the DS90CF364MTD can reduce parallel bus width and connector pin count while preserving an 18-bit display data path. System designers should still validate signal integrity, connector geometry, cable length, and grounding against the specific display and transmitter implementation. A primary design consideration is that LVDS performance depends on the complete channel, not only the receiver IC. Use controlled-impedance PCB routing, a suitable differential pair geometry, compliant input-capacitance loading, and the power and ground connections specified by the manufacturer datasheet. Keep the receiver away from noisy switching nodes and place bypassing close to the device supply pins. This product page combines the manufacturer interface description, package information, application guidance, and practical considerations for engineers evaluating the DS90CF364MTD in a flat-panel display link. The information helps distinguish receiver function, channel rate, voltage, package, and system-level design responsibilities before a prototype PCB is released.

RFQ پەیوەندی
DS90CF383AMTD - 65MHz 24-Bit LVDS Transmitter | TI
DS90CF383AMTD

DS90CF383AMTD - 65MHz 24-Bit LVDS Transmitter | TI

Texas Instruments DS90CF383AMTD is a 3.3 V programmable LVDS transmitter for 24-bit flat panel display links, operating at a maximum transmit clock frequency of 65 MHz and packaged in a 56-pin TSSOP. It accepts 28 CMOS/TTL data bits and converts them into four differential LVDS data streams, while a fifth differential link carries the phase-locked transmit clock. A flat-panel-display transmitter is an interface IC that converts parallel digital pixels into a low-voltage differential signaling link suitable for transmission between a graphics controller and a display. In the product hierarchy, the DS90CF383AMTD belongs to the LVDS interface family, which forms part of display interface ICs and broader digital signal-processing semiconductors. Its differential outputs reduce signal-integrity and EMI challenges compared with single-ended parallel routing over longer cable or cable-like interconnects. The principal device features include four LVDS data outputs, one differential clock output, a 3 V to 3.6 V supply range, and support for a 65 MHz transmit clock. Every transmit-clock cycle samples 28 input bits, allowing 24 RGB data bits and three control bits to be transferred. The programmable architecture supports configured flat-panel interfaces while maintaining a fixed parallel input side and standardized LVDS output side. Technically, the transmitter combines a parallel CMOS/TTL input interface with a phase-locked clocking and differential-output architecture. The clock is transmitted in parallel with the pixel data so the receiving endpoint can recover a timing reference from the same physical link. Four data lanes each carry seven transmitted bits in the described operating format, while the separate clock lane supports synchronization across the complete display word. Typical applications include digital flat-panel monitors, industrial human-machine-interface panels, point-of-sale displays, medical imaging terminals, automotive navigation displays, and other graphics systems that transmit 24-bit RGB data over an LVDS FPD-Link connection. The device is most appropriate where the transmitter endpoint operates from 3.3 V and the receiving endpoint supports the corresponding LVDS clock and data interface. PCB implementation requires careful treatment of the 56-pin TSSOP and its differential outputs. Place power-supply decoupling capacitors close to the supply pins, maintain continuous reference planes beneath the device, and route each differential pair as a tightly coupled pair over a controlled impedance path. Decoupling and clock-quality evaluation should be performed on the assembled PCB because package parasitics and trace geometry affect signal integrity. This product page combines the manufacturer’s device description with practical application guidance, interface-selection context, and a traceable comparison framework. It focuses on the DS90CF383AMTD’s verified architecture and package characteristics rather than introducing functionally similar parts that have not been established as pin-to-pin drop-in replacements.

RFQ پەیوەندی
DS90CF383MTD - 3.3V 65MHz LVDS Transmitter | TI
DS90CF383MTD

DS90CF383MTD - 3.3V 65MHz LVDS Transmitter | TI

Texas Instruments DS90CF383MTD is a 3.3 V, 65 MHz, 24-bit flat panel display link transmitter in a 56-pin TSSOP package. It converts 28 CMOS/TTL input bits into four LVDS data streams and one differential clock stream, transmitting 24 RGB data bits plus three control bits on every transmit-clock cycle. The interface uses low-voltage differential signaling for reliable point-to-point transfer of high-speed display data between a graphics engine and a flat-panel display controller. An LVDS flat panel display link transmitter is a specialized interface IC within the hierarchy of interface ICs, data converters, LVDS serializers, and semiconductor components. The LVDS standard transmits complementary differential signals whose common-mode rejection helps maintain signal integrity across cables and board interconnects. The DS90CF383MTD is therefore positioned between a parallel pixel-data source and a differential display-link receiver rather than serving as a general-purpose logic or voltage-conversion device. Three defining capabilities are its 24-bit RGB payload, 65 MHz transmit-clock operation, and 3.3 V supply. According to the Texas Instruments datasheet, each input cycle contains 28 bits, with 24 bits carrying RGB display data and the remaining three bits carrying control information. Four differential LVDS data outputs and a fifth differential clock output provide a compact, high-speed interface for digital display systems. The device also supports transmit-side clocking through a phase-locked transmit clock, allowing the clock and data to be transported together. The architecture reduces parallel-data fanout by serializing the display payload into low-voltage differential pairs. This can improve noise immunity and reduce connector pin count relative to carrying every parallel pixel bit over a dedicated cable. However, correct implementation depends on matched source and receiver characteristics, controlled trace or cable impedance, compliant LVDS receiver thresholds, and proper termination. The transmitter does not determine the final display resolution by itself; pixel format, timing, and receiver capabilities establish the usable video mode. Typical uses include LCD and flat-panel monitor links, industrial human-machine interface displays, digital signage, automotive navigation panels, medical imaging displays, and embedded graphics systems. The 65 MHz clock rate supports 24-bit color transfer with additional control signaling when the connected receiver and panel timing are compatible. The device is especially relevant to legacy and established display architectures that use the TI FPD-Link interface rather than newer serialized display standards. Designers should match the 56-pin TSSOP footprint, observe 3.3 V supply requirements, and implement LVDS routing with short, geometry-controlled connections. Differential pair symmetry matters because mismatched lengths and impedances can create skew and reflections. Decoupling close to the supply pins, an unobstructed ground return, and compliance with the manufacturer’s recommended input and output circuit are essential for reliable operation. This product page combines the manufacturer’s device description and datasheet information with package details, application guidance, practical layout considerations, and a focused comparison of pin-compatible transmitter options. It is designed to help engineers verify whether the DS90CF383MTD fits an existing FPD-Link design before committing to a board-level redesign or sourcing decision.

RFQ پەیوەندی