Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
DS90CF384AMTDX - 24-Bit 3.3V LVDS Receiver | Texas Instruments
The Texas Instruments DS90CF384AMTDX is a +3.3 V LVDS receiver for 24-bit flat panel display links operating at 65 MHz, packaged in a 56-pin TSSOP. It is designed for display-interface systems that require reception of serialized low-voltage differential signaling data. The device is associated with an 1800 Mbps data-rate description in the product listing, making it suitable for high-speed display link interfaces where signal integrity and receiver performance are important. An LVDS receiver is an interface circuit that converts differential data signals into logic-level signals for the receiving system. LVDS, or low-voltage differential signaling, belongs to the interface IC category and supports high-speed data transfer over balanced interconnects. The DS90CF384AMTDX is used in display applications where a transmitter sends serialized pixel or control data over a differential link and the receiver restores usable digital data for downstream logic. Key features of the device include its +3.3 V supply operation, 24-bit flat panel display link support, 65 MHz operating frequency and 56-pin TSSOP package. The 56-pin package provides the physical interface for the receiver's digital, differential and power connections. The listed operating temperature range is -10 °C to +70 °C, making the device suitable for commercial and industrial equipment where that temperature range is acceptable. The DS90CF384AMTDX is specifically identified as an LVDS interface IC for 24-bit flat panel display links. In a typical link, the receiver accepts low-voltage differential data from a display transmitter, applies receiver functions designed for the LVDS interface, and presents recovered data to the display or video processing circuitry. Designers should pay close attention to trace geometry, connector and cable topology, supply decoupling and the timing relationship between the transmitter and receiver. Typical uses include flat panel display controllers, monitor and television interface boards, industrial display equipment, test systems for display links and embedded display subsystems. The receiver can be considered when the system already uses an LVDS display link and requires a 24-bit, 65 MHz class receiver in a 56-pin TSSOP footprint. A key design consideration is the use of controlled-impedance differential routing and a properly engineered connector or cable path. Keep the receiver supply and ground connections close to the device, follow the manufacturer's recommended decoupling arrangement and validate the complete transmitter-to-receiver channel for eye margin, jitter and common-mode behavior. The DS90CF384AMTDX should be selected only when its 3.3 V supply, 24-bit link, 65 MHz frequency and TSSOP package requirements match the existing system. This product page combines manufacturer identification, interface parameters, package information, sourcing guidance and practical considerations for evaluating the DS90CF384AMTDX in a flat panel display receiver design.
DS90CF384MTD - 24-Bit 65MHz LVDS Receiver | Texas Instruments
Texas Instruments DS90CF384MTD is a 3.3 V low-voltage differential signaling receiver designed for a 24-bit flat-panel display link operating to 65 MHz. The device accepts CMOS/TTL display data through its LVDS inputs and reconstructs parallel pixel data for the display controller, supporting EIA-644 and TIA-644 LVDS signaling. It is packaged in a 56-pin TSSOP with a 0.45 V LVDS receiver output and supports display-interface data rates up to 1800 Mbps. An LVDS receiver is a high-speed differential interface component that converts low-amplitude differential signals into parallel CMOS/TTL logic. It belongs to the LVDS interface IC hierarchy, where differential signaling reduces voltage swing, provides common-mode rejection, and supports reliable point-to-point links over cables or controlled PCB traces. The DS90CF384 is intended for flat-panel display systems in which pixel and control data must cross a noisy enclosure or equipment boundary without excessive electromagnetic interference. The DS90CF384MTD operates from a 3.3 V supply and is identified as a 24-bit FPD link receiver rated for 65 MHz operation. The 56-pin TSSOP provides a compact surface-mount interface for industrial and embedded display controllers. Its differential receiver architecture supports four LVDS data streams, while CMOS/TTL output logic presents the recovered parallel data to the host controller. The receiver's designated role in the FPD link allows it to pair with the related DS90CF383B transmitter described in the device documentation. Timing behavior is central to LVDS panel systems because the transmitter's rising- or falling-edge data-strobe selection must agree with the receiver and display timing requirements. The related transmitter can be programmed for either rising-edge or falling-edge strobe operation through a dedicated pin. Designers should use the manufacturer pin-definition table and application timing diagrams when assigning control inputs, differential data pairs, and parallel outputs rather than inferring connector order from a generic LVDS receiver footprint. Typical uses include industrial HMIs, medical control panels, test instruments, automotive information displays, and other flat-panel interfaces where a 24-bit pixel bus must traverse a balanced connection. The 3.3 V supply, 65 MHz FPD link capability, and 56-pin TSSOP package make the DS90CF384MTD most appropriate where panel timing, signal integrity, and thermal margins have already been validated. For a new layout, route each differential pair as a tightly coupled, length-matched pair on a continuous reference plane and keep the receiver-side return path continuous. Follow the manufacturer's recommended decoupling, unused-pin, and test-point arrangements. This page also consolidates interface requirements, replacement constraints, package details, and practical design guidance to support component selection and PCB implementation.
DS90CF384SLC - 24-Bit 65MHz LVDS FPD Receiver | Texas Instruments
The Texas Instruments DS90CF384SLC is a 3.3 V low-voltage differential signaling receiver for 24-bit Flat Panel Display Link interfaces operating up to 65 MHz. The device is packaged in a 64-pin NFBGA measuring 8 mm by 8 mm and is identified by a 28-bit-to-4-bit receiver configuration in the manufacturer product listing. It is designed for systems that receive serialized pixel and related display-control data over a differential LVDS link. A Flat Panel Display Link receiver is an interface IC that accepts serialized, low-voltage differential signals from a compatible transmitter and reconstructs parallel data for downstream display or graphics logic. In the electronics hierarchy, this function belongs to display interface receivers, which are a subtype of interface ICs and mixed-signal semiconductors. LVDS signaling reduces the voltage swing used to represent data while providing differential noise immunity for high-speed links. The primary published characteristics of the DS90CF384SLC include a 3.3 V supply, support for a 24-bit FPD-Link interface, operation to 65 MHz, and a 28/4 receiver organization. These attributes place the device in systems requiring the receiver side of a compatible 24-bit LVDS display-link connection. The NFBGA-64 package supports compact PCB layouts, although its fine ball pitch makes careful escape routing and assembly control important. The DS90CF384SLC is primarily a receiver rather than a transmitter. It therefore belongs in the signal path between an FPD-Link-compatible source, such as a graphics or display controller, and circuitry requiring the recovered parallel data. The manufacturer product page identifies the device as a 24-bit Flat Panel Display Link receiver, while the target ordering code is associated with the 64-NFBGA, 8 mm by 8 mm package. Typical uses include flat-panel display systems, digital signage, industrial visualization equipment, medical diagnostic displays, automotive display modules, and embedded human-machine-interface panels. In each case, the source device must implement a compatible FPD-Link transmitter and electrical interface, and the PCB must preserve the controlled-impedance differential routing characteristics required by LVDS links. A key implementation consideration is the 64-ball NFBGA land pattern. Use the manufacturer pin description and package drawing to assign power, ground, differential inputs, and data outputs exactly; do not infer ball assignments from generic BGA libraries. Validate the receiver configuration, signal polarity, clocking arrangement, and display timing against the complete system interface specification before releasing a PCB layout. This product record consolidates the verified manufacturer identity, package information, interface class, and sourcing context into an engineering reference. It also distinguishes confirmed characteristics from unspecified electrical details, helping designers determine whether the device belongs in a Flat Panel Display Link architecture before committing to layout or production sourcing.
DS90CF386MTD - 3.3V 85MHz LVDS FPD Receiver | Texas Instruments
Texas Instruments DS90CF386MTD is a +3.3 V LVDS receiver for 24-bit or 18-bit flat panel display links, operating at a maximum clock frequency of 85 MHz. The device is supplied in a 56-pin TSSOP package and is identified by the DGG package designation. It converts differential LVDS serial data into parallel CMOS data for display-interface applications. An LVDS receiver, or low-voltage differential-signaling receiver, is an interface circuit that detects small differential voltages across paired conductors and converts them into digital logic signals. LVDS belongs to the broader differential-data-interface and display-interface hierarchy, where it is used to reduce signal amplitude, improve noise immunity, and support reliable high-speed transmission over a compact printed-circuit-board connection. The DS90CF386 is therefore a display-link receiver rather than a general-purpose logic buffer or voltage regulator. The receiver phase-locks to the incoming LVDS clock, samples the serial bit streams presented on the LVDS data lines, and produces parallel output data. According to the manufacturer product documentation, the receiver LVDS clock operates from 20 MHz to 85 MHz. At an incoming clock rate of 85 MHz, each LVDS input line operates at 595 Mbps, producing a maximum throughput of 2.38 Gbps for the DS90CF386 configuration. The DS90CF386 family supports 24-bit and 18-bit flat panel display links and is intended for systems requiring parallel digital data delivery after LVDS deserialization. The 56-pin TSSOP package is surface mount and provides the package arrangement used by the DS90CF386MTD ordering option. The manufacturer lists a -10°C to +70°C operating-temperature range for this ordering option. Typical applications include flat-panel LCD controller interfaces, digital display links, industrial display equipment, and other systems that transmit high-speed display data across a differential interface. The 85 MHz clock rate supports demanding pixel-data streams while the parallel output reduces the need for repeated high-speed differential reception downstream. When designing the receiver, preserve controlled-impedance routing for the LVDS clock and data pairs, keep the receiver and transmitter ground references well connected, and place bypass and termination components according to the manufacturer reference layout. Confirm the exact pin assignments and signal names for the 56-pin DGG package in the manufacturer datasheet before assigning PCB nets. This page combines the manufacturer’s interface description, package information, operating limits, and practical implementation guidance with a focused comparison of drop-in candidates. It is intended to help engineers identify the correct DS90CF386 ordering option, understand its LVDS throughput, and plan a compatible display-interface layout.
DS90CF386SLC - 85MHz 24-Bit LVDS FPD Receiver | TI
Texas Instruments DS90CF386SLC is a 3.3 V low-voltage differential signaling receiver for 24-bit flat panel display links, operating to 85 MHz and packaged in a 64-pin NFBGA (NZC) with 0.8 mm ball pitch. The receiver supports EIA-644 and TIA-644 signaling and is designed for high-speed digital video interfaces where low-voltage differential signaling reduces signal-integrity and EMI challenges. A flat panel display link receiver is an interface IC that converts a serialized differential display signal into parallel CMOS data for downstream display or timing circuitry. In the broader electronic-component hierarchy, the DS90CF386 belongs to interface ICs, specifically the LVDS receiver class used alongside flat panel display transmitters. Its differential input architecture is intended to improve noise immunity while supporting compact, high-speed connections between display controller and panel electronics. The primary identified features are an 85 MHz maximum link rate, 24-bit color data capability, a 3.3 V supply, and EIA-644/TIA-644 signaling support. The device also operates in 24-bit mode for flat panel display links. An identified comparison listing reports a 2.38 Gbps data rate for the DS90CF386 family, representing the aggregate signaling capability associated with multiple differential data lanes rather than the per-pixel clock rate. The DS90CF386 family supports both 24-bit and 18-bit flat panel display operation. Its 64-pin NFBGA option uses a 0.8 mm fine ball pitch and occupies 44 percent less PCB area than the family's 56-pin TSSOP package. This makes the NFBGA implementation particularly useful when display electronics require a compact receiver footprint, although ball-grid-array assembly requires appropriate inspection and rework capability. Typical applications include digital flat panel display interfaces, LCD controller backplanes, industrial panel displays, commercial display controllers, and embedded display systems using LVDS links. The receiver is most appropriate when the transmitter, cable or PCB channel, connector, and panel electronics have already been designed around EIA-644/TIA-644 LVDS signaling and an 85 MHz pixel-clock requirement. PCB design should preserve controlled-impedance LVDS routing, provide an uninterrupted reference plane beneath the pair, and place receiver bypass capacitance close to the supply pins. Signal-pair geometry should remain symmetrical, with matched routing through connectors and test points. Because the NFBGA package has fine-pitch balls, assembly process capability, solder-mask design, and board-side thermal and manufacturing requirements should be reviewed before committing the footprint. This page combines the device identity, package distinctions, interface applications, replacement constraints, and practical PCB considerations needed to evaluate DS90CF386SLC. It also distinguishes the compact NFBGA implementation from package variants that cannot be substituted on an existing board without footprint and pin-assignment changes.
DS90CF388VJD - 3.3V Dual-Pixel LVDS Receiver | TI
Texas Instruments DS90CF388VJD is a 3.3 V dual-pixel LVDS display-interface receiver designed for host-to-flat-panel data links supporting resolutions up to QXGA. The receiver is packaged in a 100-pin TQFP measuring 14 mm by 14 mm and is the receiving counterpart to the DS90C387 transmitter. In the dual-pixel architecture, the transmitter converts 48 bits of CMOS/TTL dual-pixel color data into eight LVDS data streams, while the DS90CF388 reconstructs and delivers the received data to the display interface. A dual-pixel LVDS display interface is a high-speed serial link used to reduce the number of conductors required between a video source and a flat-panel display. LVDS, or Low Voltage Differential Signalling, transfers complementary data signals across differential pairs. The dual-pixel arrangement processes two 24-bit pixel streams in parallel, allowing 48 bits of color information to be carried over eight LVDS data lanes. The DS90CF388VJD is therefore positioned within the broader hierarchy of display-interface ICs, interface ICs, and semiconductors. The principal features include compliance with the OpenLDI specification for digital display interfaces and support for panel resolutions from SVGA through QXGA. The interface provides DC-balanced data transmission, which helps maintain suitable duty-cycle characteristics across the serial links. At the receiver, cable deskew corrects pair-to-pair skew of plus or minus one LVDS data-bit time, supporting clock rates up to 80 MHz. Control information including VSYNC, HSYNC, DE, and two user-defined signals is transmitted during blanking intervals. The DS90CF388 is intended to be used with the DS90C387 transmitter as an endpoint pair for dual-pixel CMOS/TTL display links. Differential signaling reduces sensitivity to common-mode noise compared with single-ended parallel routing, while balanced data transfer helps limit electromagnetic interference. Receiver-side deskew compensates for propagation-delay differences between the eight LVDS data channels and therefore supports longer or less uniformly routed cable connections when the implementation follows the manufacturer’s layout and termination requirements. Typical applications include QXGA flat-panel monitor interfaces, industrial display controllers, digital signage systems, point-of-sale terminals, and embedded human-machine-interface panels. In a typical link, the host supplies parallel CMOS/TTL pixel and control data to the DS90C387, which serializes the information across LVDS pairs. The DS90CF388 receives those pairs, performs deskew and data recovery, and presents the reconstructed pixel information to the downstream display electronics. PCB implementation should preserve the differential signal topology recommended by the manufacturer, including controlled impedance, symmetrical routing, and suitable LVDS termination. Input and output interface traces should be evaluated for connector and cable parasitics, while the TQFP layout must provide adequate fanout around all 100 leads. The receiver should be placed according to the signal path so that the 80 MHz maximum clock-rate capability is not undermined by unequal routing or excessive external loading. This product page combines the functional description, package details, pin-compatible ordering variants, interface applications, and design considerations needed to evaluate the DS90CF388VJD. It also distinguishes exact drop-in ordering options from functionally similar devices that may require different circuit implementation, helping engineers confirm PCB compatibility before approving a replacement.
DS90CF562MTD - 18-Bit LVDS FPD Link | Texas Instruments
Texas Instruments DS90CF562MTD is an interface IC for an LVDS 18-bit color flat-panel display link, supplied in a 48-pin TSSOP package. The DS90CF561/DS90CF562 interface family converts 21 bits of CMOS or TTL display data into three LVDS data streams, and the family supports transmission of a phase-locked transmit clock in parallel. This combination targets reliable, scalable connections between digital graphics sources and flat-panel display panels. An LVDS flat-panel display link is an interface within the broader display-interface and data-conversion hierarchy. LVDS means low-voltage differential signaling: a small-amplitude differential signal transfers information over a balanced pair, providing useful noise immunity and allowing display data to travel between circuit boards or across a cable. The DS90CF562MTD is therefore positioned as a display-interface IC rather than a general-purpose logic device, communications transceiver, or graphics processor. Key features include 18-bit color flat-panel display support, 21-bit CMOS or TTL input data, three LVDS data streams in the associated interface family, and a 48-pin TSSOP package. The differential signaling architecture is intended for display links where data integrity, common-mode noise rejection, and deterministic clocking are important. Commercial temperature-grade positioning and surface-mount construction suit compact industrial, instrumentation, and embedded display systems. The DS90CF561/DS90CF562 interface family uses a phase-locked transmit-clock arrangement, allowing the clock to be carried in parallel with the serialized LVDS data. This architecture separates clock transport from the three low-voltage data lanes and helps the receiving display interface reconstruct the required pixel stream. Implementation still requires careful control of data timing, differential impedance, connector or cable geometry, and grounding. Typical applications include industrial flat-panel displays, test and measurement equipment with integrated screens, medical monitoring displays, point-of-sale terminals, automotive information displays, and embedded human-machine interfaces. In these systems, the interface connects a graphics engine or display controller to an LVDS-capable panel while using low-amplitude differential signaling to support longer interconnects than a conventional single-ended display bus. When laying out a board, treat the differential pairs as controlled-impedance nets and keep the transmitter and receiver interfaces away from noisy power stages. Use the manufacturer datasheet for the exact pin assignments, supply requirements, timing limits, and reference circuit before assigning tracks or selecting bypass capacitors. The 48-pin TSSOP footprint also requires adequate assembly-line spacing and a pin-one orientation that follows the package drawing. This page combines the device's documented interface function, package information, sourcing data, application context, and design guidance. It also distinguishes the exact DS90CF562MTD ordering code from related family members and explains where engineers should verify pin compatibility before treating any proposed substitute as a drop-in replacement.
DS90CF562MTDX - 280Mbps 18-Bit LVDS FPD Link | TI
The Texas Instruments DS90CF562MTDX is an 18-bit color flat-panel display (FPD) interface transmitter that converts CMOS/TTL pixel data into three LVDS data streams, supports a 280 Mbps signaling rate, operates from a 0.45 V supply, and is packaged in a 48-pin TSSOP. An LVDS FPD link is a high-speed, low-voltage differential interface used to carry pixel and control information between a display controller and a flat-panel display panel. The DS90CF562MTDX belongs to the interface IC hierarchy, where parallel CMOS data is serialized and transmitted differentially to reduce electromagnetic interference, support balanced signaling, and preserve data integrity across cable or PCB interconnect. The device supports an 18-bit color data path and three LVDS outputs. Its 280 Mbps rate provides the headroom required for legacy color flat-panel display interfaces, while the 0.45 V supply reduces the voltage required by the digital interface circuitry. The 48-pin TSSOP package provides a conventional surface-mount footprint suitable for established display-controller and panel-interface designs. DS90CF561-family devices use complementary CMOS/TTL-to-LVDS conversion to distribute serialized pixel information across differential channels. The transmitter architecture allows a display subsystem to use low-voltage differential signaling instead of carrying high-speed single-ended pixel signals directly across the board or cable, improving noise immunity and reducing radiated emissions in the completed display link. Typical applications include small color flat-panel display controllers, industrial panel interfaces, medical display modules, automotive information-display systems, and legacy computer or instrumentation panels. The device is particularly relevant when an existing design requires an 18-bit FPD link operating at 280 Mbps rather than a modern high-speed eDP or DisplayPort interface. When designing a replacement board, preserve the manufacturer-recommended input and output network, differential pair geometry, ground return, and decoupling arrangement. Confirm that the panel timing, mapping of parallel input bits to LVDS outputs, connector arrangement, and cable length match the original display architecture because a compatible IC package does not by itself guarantee panel-level interoperability. This product record consolidates the verified electrical, package, ordering, and cross-reference details with practical guidance for LCD controller, industrial panel, medical display, and legacy FPD interface designs.
DS90CR211MTD - 21-Bit LVDS Transmitter | Texas Instruments
The Texas Instruments DS90CR211MTD is a 21-bit LVDS transmitter interface IC with a 4.5 V to 5.5 V supply range in a 48-pin TSSOP package. It converts 21 CMOS/TTL input bits into three LVDS data streams and transmits a phase-locked clock, providing a compact solution for multi-bit serial links. An LVDS transmitter is a specialized interface circuit that converts low-voltage CMOS or TTL signals into balanced differential data streams. Within the signal-chain hierarchy, it belongs to the LVDS interface family, differential line-driver class, and broader interface IC category. Balanced signaling improves noise immunity and enables reliable data transfer over longer printed-circuit-board traces than ordinary single-ended digital interfaces. The DS90CR211MTD accepts 21 parallel data bits and serializes them into three differential LVDS lanes. It also forwards a phase-locked transmit clock, allowing the receiver to recover timing from the transmitted stream. The manufacturer describes the device as a 21-bit Channel Link transmitter, and its architecture is intended for transferring parallel digital data over a compact differential interface. The operating supply range of 4.5 V to 5.5 V supports conventional 5 V interface environments. The 48-TSSOP package offers a relatively high pin count for a parallel-to-serial transmitter, accommodating the 21 data inputs, differential outputs, clock path, power connections, and control functions. Its rectangular surface-mount construction is suitable for automated assembly and multilayer PCB designs. Typical uses include point-to-point digital backplanes, industrial control links, test and measurement equipment, communication modules, and embedded systems that need to move parallel data across a PCB without relying on a parallel bus. LVDS is especially useful when signal integrity, trace routing, or data-transfer distance becomes more important than connector pin count. When laying out the transmitter, treat every differential pair as a controlled-impedance route and keep the LVDS outputs short and properly terminated according to the receiver implementation. Confirm the receiver's supported data format, clocking method, supply voltage, and termination before treating the DS90CR211MTD as a drop-in component in a new design. This product page combines the manufacturer interface description with package information, practical PCB guidance, source-backed alternatives, and a parameter comparison designed to accelerate component selection and board-level integration.
DS90CR212MTD - 48-TSSOP LVDS Line Receiver | TI
The Texas Instruments DS90CR212MTD is a quad LVDS line receiver designed for receiving low-voltage differential signals, with four receivers arranged in a 48-pin TSSOP package. The device is associated with 21-bit Channel Link signaling, operates over a commercial temperature range of -10°C to +70°C, and is supplied in a surface-mount rectangular package with gull-wing leads. Its 48-terminal package and balanced differential inputs position it for point-to-point digital links that require a dedicated receiver function. An LVDS line receiver is an interface IC that detects the voltage difference between two complementary conductors and converts that differential information into a CMOS-compatible logic signal. Within the signal-chain hierarchy, an LVDS receiver belongs to the broader family of differential line receivers, interface ICs, and semiconductor devices. This category is distinct from an LVDS transmitter: the receiver restores valid digital logic at the far end of a cable or board-to-board connection after differential transmission. The DS90CR212MTD provides four line-receiver channels in one package, reducing component count on multi-channel interface boards. Its rectangular 48-pin TSSOP construction is intended for surface-mount assembly, while the commercial temperature range covers applications operating from -10°C through +70°C. The package body measures 12.5 mm by 6.1 mm according to the product listing, allowing it to be accommodated on boards requiring a higher pin-count interface package rather than a small-outline package. The DS90CR212MTD is categorized as a specialized interface IC and is specifically described as an LVDS line receiver. Its channel architecture is intended to accept low-amplitude differential signaling, which is commonly used to carry clock or data information over balanced interconnects. The exact signaling rate, input voltage range, supply voltage, output timing, and input impedance must be confirmed from the manufacturer datasheet before a new design relies on those values. Typical implementation areas include multi-channel digital backplanes, industrial control links, embedded data acquisition, test and measurement systems, and communications equipment that uses balanced interconnects. Consolidating four receivers into one package is particularly useful when a system must terminate or translate several parallel differential signals. Board designers should preserve controlled-impedance routing and provide the decoupling and grounding arrangements recommended for high-speed interface circuits. The primary layout consideration is the pin density of the 48-terminal TSSOP package. Use the manufacturer pin-description table to assign supply, ground, differential inputs, and logic outputs, and keep unused inputs in their specified termination states. Because no complete pin map is published on the product pages associated with this part, verify each connection against the current Texas Instruments datasheet rather than inferring functions from neighboring pins. This product record combines package, environmental, interface-classification, and cross-reference information with practical implementation guidance. It also identifies nearby same-package TI line-receiver options for design reviews while clearly separating confirmed attributes from parameters that require datasheet confirmation. Use the Request a Quote form on this page for current commercial availability, lead time, and sourcing requirements.
DS90CR213MTD - 21-Bit 66MHz Channel Link | Texas Instruments
The Texas Instruments DS90CR213MTD is a 21-bit Channel Link interface IC operating at 66 MHz, supplied in a 48-terminal TSSOP package. It supports a maximum supply voltage of 5.25 V and is designed for commercial-temperature operation from -10°C to +70°C. The device is associated with the EIA-644 and TIA-644 interface standards, placing it within the broader hierarchy of LVDS interface ICs, digital interface controllers, interface adapters, and semiconductors. A Channel Link interface is a high-speed serializing and deserializing interface that transfers multiple low-speed parallel data bits over a balanced differential link. The 21-bit width allows parallel data from a controller, processor, display, or communications equipment to be transferred efficiently over fewer conductors than a conventional parallel bus. The 66 MHz operating rate gives the interface a nominal 21-bit parallel-to-serial transfer capability of 1.386 Gb/s before protocol overhead. The DS90CR213MTD is identified as a line-driver-class interface device in commercial catalogs. Key cataloged attributes include 48 gull-wing terminals, a TSSOP package, a 5.25 V maximum supply voltage, and a -10°C to +70°C operating-temperature range. Its 12.5 mm package length supports compact printed-circuit-board placement while preserving adequate lead spacing for automated assembly and inspection. The EIA-644 and TIA-644 references place the device within standardized low-voltage differential-signaling interface practice. Differential signaling is valuable in systems where low voltage noise tolerance, reduced ground-reference sensitivity, and controlled signal polarity are important. The exact clocking, termination, connector, and system-bus requirements should be implemented according to the pin-description table and application guidance in the manufacturer datasheet. Typical uses include point-to-point Channel Link connections between industrial controllers, test equipment, video or imaging subsystems, computer peripherals, and communications hardware. In each case, the 21-bit word width and 66 MHz signaling rate support compact high-speed transfers while limiting the number of inter-board conductors. When laying out the circuit, preserve the differential-signal topology specified by the manufacturer datasheet, maintain the intended transmission-line impedance, and place termination and interface components close to their corresponding device pins. Confirm that the 5.25 V maximum supply rating, operating-temperature range, and logic levels match the intended system before releasing the layout. This product page combines the exact catalog attributes of the DS90CR213MTD with interface guidance, drop-in family references, and application-oriented design considerations. Use the manufacturer pinout and interface-standard documentation to complete board-level signal-integrity and power-distribution decisions.
DS90CR216AMTDX - 21-Bit LVDS Receiver | Texas Instruments
The Texas Instruments DS90CR216AMTDX is a +3.3 V rising-edge data-strobe LVDS receiver designed for 21-bit Channel Link interfaces operating at up to 66 MHz. It is packaged in a 48-pin TSSOP (DGG) package and is identified by the manufacturer as a 1.386 Gbps LVDS interface device. The receiver is intended for systems that require low-voltage differential signaling across board, cable, or backplane connections where signal integrity, clock recovery, and deterministic data transfer are important. Its single-ended CMOS-side interface works with LVDS signaling on the differential side, helping connect older parallel digital systems to modern high-speed serial links. The DS90CR216A family is associated with the DS90CR215/DS90CR216 3.3 V rising-edge data-strobe LVDS Channel Link architecture. The 21-bit parallel data path supports transfers of 21 bits per channel at the stated 66 MHz operating frequency, corresponding to the listed 1.386 Gbps class of aggregate signaling performance. The device is a receiver rather than a transmitter, so the system designer must provide the complementary LVDS source, clocking, termination, and downstream logic. The rising-edge data-strobe arrangement supports designs that recover data and transfer timing from the incoming differential signal rather than relying on a separate parallel source-synchronous clock. The principal engineering benefits are reduced connector pin count compared with a parallel-only implementation, differential noise immunity over longer interconnects, and compatibility with established Channel Link signaling conventions. The 48-pin TSSOP package provides a standard surface-mount footprint and is suitable for compact industrial, communications, and embedded control systems. Because the device operates from a single +3.3 V supply, the power architecture is straightforward, although supply decoupling and LVDS return-path design remain critical. Typical uses include industrial control links, point-to-point backplanes, embedded video or data acquisition systems, and communication equipment using LVDS over copper. In these applications, the receiver converts a differential LVDS data stream into a 21-bit parallel CMOS data bus while providing the associated strobe or clocking behavior expected by Channel Link designs. The parallel output can connect directly to FPGA, ASIC, DSP, or microcontroller interface logic when voltage, timing, and signal-integrity requirements are satisfied. A practical design should follow the manufacturer datasheet for pin assignment, termination, decoupling, and layout. Place the receiver close to the connector or cable entry, keep LVDS traces short and tightly matched, provide the required differential termination, and route the outputs to controlled-impedance CMOS destinations. Confirm that the source voltage, cable length, data rate, and downstream input thresholds are compatible before releasing a production board. This page summarizes the manufacturer product identity, package, interface class, commercial information, and design implications of the DS90CR216AMTDX. It also distinguishes the documented device from related ordering variants and focuses replacement decisions on same-package, pin-compatible LVDS receivers rather than functionally similar but mechanically different parts.
DS90CR216MTD-TI - 21-Bit 66MHz LVDS Receiver | Texas Instruments
Texas Instruments DS90CR216MTD-TI is a +3.3 V rising-edge data-strobe LVDS receiver for a 21-bit Channel Link interface, operating at up to 66 MHz and packaged in a 48-pin TSSOP. It receives 21 parallel low-voltage differential data signals and a differential clock while providing serialized data and strobe outputs for reliable point-to-point or balanced cable communication. A Channel Link receiver is a high-speed interface circuit that converts parallel source-synchronous data into a differential, clock-forwarded transmission format. In the broader semiconductor hierarchy, it belongs to the interface IC class and uses LVDS signaling to reduce voltage noise, ground-reference requirements, and conductor count compared with an unwrapped parallel bus. The DS90CR216 family is intended for high-speed point-to-point links carrying video, control, or general digital data. The principal operating characteristics are a +3.3 V supply, a 66 MHz maximum data-strobe frequency, 21 data outputs, and a 48-pin TSSOP package. Its rising-edge data-strobe architecture transfers data on the clock edge for a deterministic sampling arrangement. Differential signaling improves common-mode noise rejection, while the multiplexed LVDS outputs reduce cable size relative to routing 21 separate single-ended signals over a long distance. The receiver includes 21 parallel data inputs, a differential clock input, differential data and strobe outputs, and power-ground connections. Its electrical performance depends on correct termination, controlled-impedance routing, and stable supply decoupling. Because the data and strobe are transmitted differentially, the interface can reject a substantial amount of common-mode noise while preserving signal timing over a cable or backplane connection. Typical uses include industrial control links, video transport systems, instrumentation, embedded display connections, and equipment requiring a compact multi-bit differential interface. The 21-bit width is especially useful where transferring each bus as separate single-ended traces would consume excessive board area or cable conductors. Systems must account for propagation delay between the clock and data channels when defining timing margins. For implementation, follow the pin-description table and recommended external-circuit diagram in the manufacturer datasheet. Place the differential clock and data traces with controlled impedance, keep the input and output interfaces away from high-current switching paths, and validate connector or cable length against the required transfer rate. Do not treat TSSOP lead spacing as a substitute for correct high-speed routing discipline. This page combines the family-level operating data with practical interface guidance, verified replacement candidates, and a package-aware comparison. It is intended to help engineers identify the correct LVDS Channel Link receiver, verify replacement compatibility, and plan a signal-integrity-conscious implementation rather than relying only on a basic component description.
DS90CR216MTDX/NOPB - 3.3V LVDS 21-Bit Channel Link Receiver | TI
The DS90CR216MTDX/NOPB is a 3.3V LVDS (Low-Voltage Differential Signaling) receiver from Texas Instruments that converts three LVDS data streams and one LVDS clock back into 21 bits of parallel LVCMOS data. It is part of the Channel Link chipset, designed for high-speed data transmission over reduced conductor counts. The device operates from a 3.0V to 3.6V supply and supports LVDS clock rates from 20 MHz to 66 MHz, corresponding to data rates up to 1386 Mbps. It is housed in a 48-pin TSSOP package (also referred to as 48-TFSOP) with a 6.10mm width, and is available in tape and reel packaging. What is an LVDS receiver? LVDS (Low-Voltage Differential Signaling) is a high-speed, low-power interface standard used to transmit data over twisted-pair or PCB traces. An LVDS receiver is a specialized interface IC that converts differential LVDS signals back into single-ended CMOS/TTL logic levels. In the hierarchy of interface ICs, an LVDS receiver falls under the category of high-speed serializers/deserializers (SerDes) and is a key component in display interfaces, industrial video links, and automotive infotainment systems. The DS90CR216 is specifically a deserializer that reconstructs parallel data from a serialized LVDS stream. Key features of the DS90CR216MTDX/NOPB include a 21-bit parallel output, rising-edge data strobe, and backward compatibility with existing 5V Channel Link transceivers (DS90CR213/DS90CR214). The device provides substantial cable reduction: a 21-bit wide data bus plus clock typically requires up to 44 conductors in a single-ended parallel interface, but with Channel Link, only 9 conductors (3 data pairs, 1 clock pair, and ground) are needed. This reduces cable size, cost, and EMI. The receiver also features a power-down mode and supports interconnects up to 5 meters depending on cable quality. Technically, the DS90CR216 uses a differential signaling scheme with a typical differential output voltage of 0.45V, ensuring low electromagnetic interference and high noise immunity. The device is designed for point-to-point or multi-drop configurations and includes internal termination for the LVDS inputs. The rising-edge data strobe simplifies timing by aligning data capture with the clock edge, reducing setup/hold requirements. The receiver is specified for the industrial temperature range of -40°C to +85°C, making it suitable for harsh environments. Typical applications include flat panel display interfaces, digital video transmission, industrial machine vision, and automotive camera links. The DS90CR216 is often paired with the DS90CR215 transmitter to form a complete Channel Link solution. When designing with this device, ensure proper PCB layout with controlled impedance traces for the LVDS pairs and place the receiver close to the connector to minimize skew. Also, provide adequate decoupling on the VCC pins with 0.1uF and 10uF capacitors. In summary, the DS90CR216MTDX/NOPB is a robust, high-speed LVDS receiver that simplifies data transmission in space-constrained applications. Its low-voltage operation and reduced conductor count make it an efficient choice for modern digital interfaces.
DS90CR217MTD - 3.3V LVDS 21-Bit Transmitter | Texas Instruments
Texas Instruments DS90CR217MTD is a 3.3 V rising-edge data-strobe LVDS transmitter designed for high-speed digital point-to-point links. The device accepts 21 parallel CMOS/TTL data bits and a clock, then serializes the payload into three differential LVDS data streams plus a separate LVDS clock output. Its 85 MHz rising-edge Channel Link interface supports transfer rates of 1.785 Gbps and is designed for use in display, video, communications, and industrial control systems. An LVDS transmitter is a differential signaling interface IC that converts low-voltage CMOS/TTL logic into low-voltage differential signals. This technique reduces signal amplitude while improving noise immunity and allowing reliable transmission across cable or PCB connections. The DS90CR217MTD belongs to the LVDS interface IC hierarchy, alongside differential line drivers, receivers, serializers, and Channel Link devices. The primary electrical features include a 3.3 V supply, 21-bit parallel data input, three LVDS outputs, and an 85 MHz maximum rising-edge data-strobe frequency. The 48-pin TSSOP package supports compact board layouts, while the differential outputs are intended for controlled-impedance routing. The transmitter architecture is particularly useful when a system needs to move parallel digital data across a board-to-board cable, backplane, or external module. Typical applications include video and display interfaces, industrial visualization systems, test equipment, imaging systems, and communications equipment. When selecting this transmitter, verify the receiver's clocking convention, lane mapping, termination arrangement, cable length, and LVDS voltage levels before releasing a PCB layout. The manufacturer datasheet should be used for the complete pin list, electrical limits, timing values, and recommended termination network.
DS90CR282MTD - 28-Bit LVDS Channel-Link Receiver | Texas Instruments
Texas Instruments DS90CR282MTD is a 28-bit Channel-Link receiver that recovers four parallel LVDS data streams and an embedded differential clock from a serialized source. It operates from a 4.5 V to 5.5 V supply and is packaged in a 56-pin TSSOP. The receiver converts four differential LVDS data pairs into 28 parallel CMOS/TTL output bits while supporting high-speed point-to-point digital links. A Channel-Link receiver is a specialized interface IC that bridges the voltage and signaling domains between a high-speed differential transmitter and downstream parallel logic. The DS90CR282MTD belongs to the broader low-voltage differential signaling interface hierarchy: Channel-Link receiver, differential line receiver, digital interface IC, and semiconductor. Its role is to deserialize or reconstruct parallel data from a compact group of differential conductors, reducing connector pin count while preserving a parallel data presentation to the receiving system. The principal interface characteristics include a 28-bit parallel data width, four LVDS data streams, LVDS protocol support, and a 4.5 V to 5.5 V supply range. These features make the device applicable to industrial control systems, digital video processing, instrumentation, test equipment, and embedded systems that use a Channel-Link transmitter such as the DS90CR281. The wide parallel output interface allows each recovered bit to be routed directly into FPGA, ASIC, or other digital logic. Operationally, the receiver relies on differential signaling to reject common-mode voltage and reduce sensitivity to noise encountered along a cable or PCB interconnect. Differential clock recovery coordinates the parallel outputs, while the four LVDS lanes carry groups of serialized data. Board-level implementation must preserve controlled impedance, short return paths, and adequate coupling between the transmitter and receiver. Power and ground distribution should be planned to prevent simultaneous output switching from disturbing adjacent sensitive circuitry. Typical uses include transferring control and pixel data in video-processing equipment, transporting automation commands between distributed controllers, and carrying parallel bus data over a compact cable connection. The interface is particularly useful when a design already uses a Channel-Link-compatible transmitter and therefore benefits from a standard 28-bit parallel receiver architecture. A principal design consideration is signal integrity. The differential pairs require matched routing, suitable layer-stack geometry, and compliant LVDS input capacitance. The supply rails need local high-frequency decoupling, while the parallel output timing budget must include receiver latency and clock-alignment requirements. Power sequencing and signal integrity should be evaluated together because a stable supply does not compensate for an incorrectly implemented differential channel. This product overview combines the confirmed device identity, interface width, supply range, protocol, package, and packaging information with practical guidance for LVDS routing, decoupling, timing, and source selection. It also distinguishes direct drop-in alternatives from related Channel-Link parts that may require a different transmitter, voltage, protocol, or board footprint.
DS90CR283MTDX/NOPB - 5V LVDS 28-Bit Channel Link Transmitter | TI
The Texas Instruments DS90CR283MTDX/NOPB is a 28-bit Channel Link transmitter that converts 28 bits of CMOS/TTL data into four LVDS (Low Voltage Differential Signaling) data streams, with a phase-locked transmit clock transmitted in parallel. Operating from a 4.75V to 5.25V supply, this device supports data rates up to 66 MHz, delivering a total throughput of 1.848 Gbps. Housed in a 56-pin TSSOP (TFSOP) package, it is designed for high-speed point-to-point data transmission over PCB traces or cables, minimizing EMI and reducing interconnect count. Channel Link is a proprietary interface technology developed by National Semiconductor (now part of Texas Instruments) that serializes parallel data into LVDS pairs. This device belongs to the family of LVDS interface ICs, which are used to transmit high-speed digital data with low power consumption and excellent noise immunity. The DS90CR283MTDX/NOPB is the 5V version of the popular DS90CR285, which operates at 3.3V, making it suitable for legacy 5V logic systems. Key features include a 28:4 data compression ratio, a rising-edge data strobe, and a phase-locked loop (PLL) for clock generation. The transmitter accepts 28 single-ended CMOS/TTL inputs and outputs four LVDS data pairs plus one LVDS clock pair. The device supports a wide input clock range and includes a power-down mode to reduce quiescent current. The TSSOP-56 package offers a compact footprint for space-constrained designs. Technically, the DS90CR283MTDX/NOPB uses a differential signaling scheme with a typical output voltage swing of 350 mV across a 100-ohm termination resistor. The LVDS outputs are current-mode drivers that provide low electromagnetic interference (EMI) and high noise immunity. The PLL ensures that the transmitted clock is aligned with the data, simplifying receiver timing. The device is specified for the commercial temperature range (0°C to 70°C) and is RoHS compliant. Typical applications include flat panel displays, digital video interfaces, and high-speed data links in industrial and consumer electronics. The 5V supply makes it ideal for interfacing with legacy TTL logic. When designing with this device, ensure proper termination of the LVDS lines with 100-ohm resistors and maintain controlled impedance on the PCB to preserve signal integrity.
DS90CR285MTD - 28-Bit 66MHz LVDS Transmitter | Texas Instruments
The Texas Instruments DS90CR285MTD is a 28-bit Channel Link LVDS transmitter operating from a 3.3 V supply and supporting a 66 MHz rising-edge data strobe. The device converts 28 LVCMOS/LVTTL input bits into four differential LVDS data streams and transmits a phase-locked differential clock over a fifth LVDS link. It is housed in a 56-pin TSSOP package rated for -40°C to +85°C operation. An LVDS transmitter is a high-speed interface device that converts low-voltage complementary logic into balanced differential signals. LVDS belongs to the broader differential-interface and data-transceiver hierarchy, where low signal amplitude, common-mode rejection, and reduced electromagnetic interference support reliable point-to-point data transfer. DS90CR285 devices are commonly positioned between parallel digital logic and a high-speed LVDS link on displays, industrial controllers, and communications equipment. The principal features include 28 parallel data inputs, four LVDS data outputs, one additional LVDS clock output, and a 66 MHz maximum parallel-clock frequency. The transmitted clock is phase-locked to the source data, allowing the receiving system to recover timing. The device also accepts a rising-edge data strobe and operates from a single 3.3 V supply. Its 56-pin TSSOP package provides a conventional surface-mount interface for systems using high-density parallel-to-differential signaling. The transmitter architecture divides the 28-bit parallel payload into four differential data lanes and provides a separate clock lane. This arrangement limits the number of high-speed differential conductors required to carry the payload. Compared with single-ended parallel transmission, the balanced outputs improve noise immunity and can reduce connector and PCB signal-integrity problems when the receiver, termination network, trace geometry, and clock distribution are designed correctly. Typical uses include digital display interfaces, flat-panel monitor backplane links, industrial imaging equipment, video-processing systems, test equipment, and embedded control systems that exchange parallel data over a short differential cable or board-level LVDS connection. The transmitter is also suitable where a source device has a 28-bit parallel bus but the destination requires a smaller number of low-voltage differential conductors. PCB implementation should treat the LVDS outputs as controlled-impedance differential pairs. Route each pair continuously over a solid reference plane, keep the spacing within the pair consistent, and place the receiver-side termination close to the receiver. Avoid adding test pads or routing discontinuities that create impedance mismatches, and verify AC-coupled or DC-coupled connectivity against the receiver's input requirements. This product record combines the device's key interface characteristics, package information, sourcing guidance, compatible ordering variants, and practical implementation considerations. It helps engineers identify the correct Texas Instruments LVDS transmitter, compare its electrically identical ordering options, and plan a robust 28-bit parallel-to-LVDS interface before committing a PCB layout.
DS90CR285SLC - 28-Bit 66MHz LVDS Transmitter | TI
Texas Instruments DS90CR285SLC is a 28-bit rising-edge data-strobe LVDS transmitter rated for 66 MHz and packaged in a 64-NFBGA (8 x 8 mm) package. It operates from a 3 V to 3.6 V supply and converts 28 bits of LVCMOS or LVTTL data into four differential LVDS outputs, with one clock channel providing a 66 MHz data-strobe interface. A low-voltage differential signaling transmitter is an interface IC that transfers high-speed data between circuit boards or between devices over differential pairs. LVDS belongs to the broader interface-IC hierarchy, where low-voltage, low-power differential signaling is used for clock distribution, video, graphics, communications, and industrial control systems. Compared with single-ended parallel signaling, LVDS provides common-mode noise rejection and enables reliable transmission through controlled-impedance interconnects. The DS90CR285 provides a 28-bit parallel input and serializes that data across four LVDS data outputs at up to 66 MHz. The 3 V to 3.6 V operating range supports conventional 3.3 V digital systems. The 64-NFBGA package provides a compact surface-mount footprint, while its many connections support separate data channels, differential pairs, power, ground, and control functions. The transmitter is designed for parallel-to-LVDS conversion where a source device must communicate with an LVDS receiver over a balanced cable, backplane, or controlled-impedance PCB channel. Its rising-edge data-strobe architecture carries a forwarded clock alongside data, allowing the receiving system to establish a deterministic sampling relationship. Systems using this device must account for signal-pair geometry, termination, trace impedance, connector loss, and skew between the clock and data channels. Typical uses include industrial control systems, data-acquisition equipment, display and graphics interfaces, telecommunications equipment, and embedded systems that connect a CMOS parallel bus to an LVDS link. The 66 MHz operating rate and four differential outputs make the device especially relevant to multi-lane transfers requiring more aggregate bandwidth than a single LVDS pair can provide. For layout, route each differential pair as a tightly coupled, length-matched pair over a continuous reference plane. Place receiver-side termination close to the endpoint and verify AC coupling, biasing, and clock/data alignment in the complete channel. Because the package has 64 balls, inspect the manufacturer pin-description table before assigning power, ground, data, clock, and no-connect positions to the PCB. This page combines the device’s documented interface characteristics, practical PCB implementation guidance, sourcing questions, and an explicit assessment of drop-in replacement evidence. It also highlights the distinction between a mechanically similar serializer and a genuinely pin-compatible substitute, helping engineers avoid replacement assumptions that could compromise signal integrity or system functionality.
DS90CR286AMTDX - 28-Bit LVDS Receiver | Texas Instruments
Texas Instruments DS90CR286AMTDX is a 3.3 V rising-edge data-strobe LVDS receiver designed for 28-bit Channel Link transfers at up to 66 MHz. The device is offered in a 56-pin DGG TSSOP package and supports a -40°C to 85°C operating-temperature range. An LVDS receiver is an interface circuit that converts low-voltage differential signaling into a logic-level output. It belongs to the signal-chain hierarchy of transceiver ICs, interface ICs, and semiconductors. LVDS, or Low-Voltage Differential Signaling, provides a noise-resistant method for transferring high-speed data across a cable or PCB link while using low signal amplitudes. The DS90CR286A family is intended for parallel-to-serial data-strobe connections between processors, controllers, displays, imaging equipment, and other digital systems. The receiver accepts eight LVDS data channels plus a differential clock, reconstructs the parallel data at the receiver, and supplies a data-strobe clock output. Its 20 MHz to 66 MHz shift-clock support and 50% receiver-output-clock duty cycle are important for systems that transfer wide parallel data over a compact differential link. The manufacturer also identifies compatibility with the TIA/EIA-644 LVDS standard, low-profile 56-pin or 48-pin DGG TSSOP options, and an automotive-qualified Grade 3 option within the DS90CR286A family. Channel Link is a parallel bus architecture that separates data and clock rather than relying on source-synchronous clocking. This arrangement can simplify implementation in older computing, industrial-control, display, and machine-vision systems. By carrying data and clock across balanced differential lines, the interface reduces sensitivity to common-mode noise and can support reliable transmission where a single-ended bus would be more susceptible to crosstalk and ground-offset problems. Typical uses include industrial imaging systems, video-processing equipment, display controllers, printers, machine-vision hardware, and embedded parallel-bus interfaces. When implementing the receiver, preserve the differential pair geometry specified by the manufacturer, provide an appropriate LVDS termination and bias network at the transmitter side, and route the recovered clock and data outputs as ordinary single-ended digital signals. Keep the receiver and its decoupling capacitors close to the source impedance and observe the recommended layer-stack and return-path arrangement to minimize edge degradation. For clock-sensitive designs, check receiver output setup and hold timing against the receiving logic rather than relying only on the 66 MHz clock limit. The automotive Grade 3 variant should be selected only when the complete system requires that qualification; the DS90CR286AMTDX ordering designation must also be checked for its exact package, temperature range, reel or tube configuration, and lead-free status before placement. This page combines family-level specifications, ordering distinctions, drop-in candidates, and interface-level design guidance to simplify component selection and PCB integration.
DS90CR286ASLC - 28-Bit LVDS Channel-Link Receiver | Texas Instruments
The Texas Instruments DS90CR286ASLC is a 3.3 V rising-edge data-strobe LVDS receiver that converts four differential LVDS data streams into 28 parallel CMOS/TTL data bits. It is designed for 28-bit Channel Link communication at up to 66 MHz and uses a 64-pin NFBGA package, identified in distributor information as an 8 x 8 mm package. The receiver is intended for high-speed point-to-point links where four LVDS data channels and a separate clock channel carry data from a transmitter to a receiving device. A Channel Link receiver is an interface IC that reconstructs parallel digital data from differential low-voltage differential signaling pairs. LVDS, or low-voltage differential signaling, is a high-speed electrical interface designed to reduce common-mode noise and support reliable data transfer over balanced conductors. The DS90CR286ASLC is therefore positioned within the interface-IC hierarchy, alongside parallel-to-serial and serial-to-parallel data converters, rather than with general-purpose logic or memory devices. The main functional characteristics visible in the manufacturer and distributor information are the 4-to-28 LVDS-to-parallel conversion, 3 V to 3.6 V supply range, 66 MHz channel-link operating frequency, and up to 1.848 Gbps throughput or 231 MB/s bandwidth. The rising-edge data-strobe architecture allows the receiver to transfer 28 data bits in parallel while the companion DS90CR285 transmitter serializes the corresponding data stream. The use of LVDS can help reduce signal-integrity problems associated with single-ended high-speed interconnects. The DS90CR286ASLC is used in industrial data acquisition, test and measurement equipment, instrumentation, communications equipment, and other systems requiring a high-speed parallel data interface. The receiver can be paired with a compatible transmitter and an FPGA or other parallel-processing device. Designers must account for the specified 3.3 V supply, correct LVDS input termination and topology, clock/data-strobe alignment, decoupling, and the package's thermal and layout requirements. For PCB implementation, place the receiver close to the LVDS connector or transmitter, follow the manufacturer's recommended decoupling and controlled-impedance routing, and keep unused inputs in the states specified by the datasheet. The package pinout and detailed electrical limits should be taken from the current Texas Instruments DS90CR286 datasheet before final schematic and layout release. This page organizes the available technical information, sourcing guidance, comparison points, and design considerations around the DS90CR286ASLC.
DS90CR286MTD - 28-Bit 66MHz LVDS Receiver | Texas Instruments
Texas Instruments DS90CR286MTD is a 28-bit channel-link receiver that converts differential LVDS data into 28-bit LVCMOS/LVTTL data. It operates from a 3.3 V supply, supports a 66 MHz transmit clock, and handles 462 Mbps per LVDS data channel. The device is packaged in a 56-pin TSSOP and uses rising-edge data strobing. A channel-link receiver is an interface integrated circuit that terminates low-voltage differential signaling and reconstructs parallel logic data at the receiving end of a point-to-point link. In the electronic-component hierarchy, it is an interface IC, a data-conversion device, and a semiconductor. Its primary role is to connect a high-speed differential transmitter to a digital controller, processor, FPGA, or other parallel-logic receiver while maintaining a controlled signal path across the cable or PCB interface. The defining electrical characteristics of the DS90CR286MTD are its 28-bit data width, 66 MHz operating clock, 3.3 V supply, and 462 Mbps per-channel data rate. It accepts four LVDS data inputs and provides 28 LVCMOS/LVTTL outputs in the 56-pin TSSOP package. The rising-edge data-strobe architecture allows the receiver to transfer parallel data on the designated clock edge. Industrial temperature-grade ordering information identifies the device for industrial equipment applications. The receiver is intended for high-speed point-to-point links where parallel logic cannot be carried directly across the interconnect. Its differential inputs are suited to balanced cable or PCB channels because they reduce sensitivity to common-mode noise compared with single-ended transmission. The parallel LVCMOS/LVTTL output side is compatible with digital logic systems, although output timing, trace length, and termination details must be controlled at the board level. Typical uses include industrial control systems, test equipment, instrumentation, embedded processors, communication modules, and FPGA or CPLD data interfaces. The 462 Mbps per-channel capability is particularly relevant when a system must transfer 28 parallel bits across a compact differential link. In a transmitter-receiver pair, the companion device supplies the corresponding serialized differential signals, while the DS90CR286MTD restores the parallel data bus for downstream logic. Layout is a central engineering consideration because the difference between a correctly designed channel and a marginal one is often determined by controlled impedance, pair geometry, grounding, and return-path continuity. Place the receiver close enough to the link connector or transmitter to minimize the unterminated differential segment, maintain a continuous reference plane, and route the LVDS pair as a tightly coupled pair. The manufacturer data sheet should govern capacitor selection, connector pin assignments, and any recommended test or termination arrangements. This product overview combines the device identity, electrical operating points, packaging information, application context, and replacement considerations with practical design guidance. It is intended to help engineers determine whether the DS90CR286MTD fits a 3.3 V, 66 MHz channel-link architecture before beginning PCB implementation or production sourcing.
DS90CR287MTD - 85MHz 28-Bit LVDS Transmitter | Texas Instruments
The Texas Instruments DS90CR287MTD is a +3.3 V rising-edge data-strobe LVDS 28-bit Channel Link transmitter with an 85 MHz operating frequency, four LVDS data outputs plus a transmitted clock, and a 56-pin TSSOP package. It converts 28 parallel LVCMOS/LVTTL input bits into four differential LVDS data streams while forwarding a phase-locked transmit clock on a fifth LVDS link. A Channel Link transmitter is a high-speed parallel-to-differential interface IC used to move multiple data bits across a cable or PCB interconnect. The DS90CR287 belongs to the LVDS interface IC hierarchy, which includes differential line drivers, channel-link serializers, clock transmitters, and receiver counterparts. Its parallel-to-LVDS architecture reduces the number of signal conductors required for wide data transfers while supporting reliable clocking across that link. The principal features include 28 LVCMOS/LVTTL data inputs, four LVDS data streams, a fifth differential clock output, an 85 MHz operating frequency, and operation from a +3.3 V supply. The transmitter is intended for rising-edge data-strobe applications and supports an industrial temperature range of -10°C to +70°C. A 56-pin TSSOP provides adequate routing density for the wide parallel input interface and five differential outputs. Technically, the device serializes each cycle of the transmit clock into four differential data lanes. The transmitted clock provides a source-synchronous reference at the receiver, allowing the receiving system to capture the data relative to the forwarded clock. This architecture is useful when the source and destination must exchange parallel data across a limited number of high-speed conductors while retaining deterministic timing. Typical applications include industrial imaging equipment, video transport systems, data-acquisition modules, digital cameras, test and measurement instruments, and industrial control panels. The 28-bit parallel input and multi-lane LVDS output can reduce connector pin count compared with driving every parallel bit as a single-ended signal, especially in space-constrained equipment. The key design consideration is that the LVDS link still requires controlled impedance, short stubs, suitable connectors, and compliant differential routing. Input and output timing, cable length, connector behavior, and receiver capability determine whether the full 85 MHz operating rate is practical in a specific system. This product page organizes the DS90CR287MTD interface details, verified source links, replacement analysis, and application guidance into a design-focused reference for engineers evaluating parallel-to-LVDS data links.
DS90CR288AMTDX - 85 MHz 28-Bit LVDS Receiver | Texas Instruments
The Texas Instruments DS90CR288AMTDX is a +3.3 V rising-edge data-strobe LVDS receiver for a 28-bit Channel Link interface, operating up to 85 MHz in a 56-pin TSSOP package. The receiver supports 20 MHz to 85 MHz shift-clock operation and provides a 50% duty-cycle receiver output clock. It is designed to deserialize four LVDS data streams carrying 28 bits of parallel data into an LVCMOS or LVTTL output bus. A Channel Link serializer or transmitter converts parallel logic data into low-voltage differential signaling for reliable transfer across cables, backplanes, and circuit-board interconnects. An LVDS interface receiver reverses that process by detecting the differential voltage on each pair and reconstructing the corresponding digital bit stream. The DS90CR288AMTDX therefore belongs to the interface-IC hierarchy: LVDS receiver, high-speed interface IC, data converter, and semiconductor. Principal features include an 85 MHz maximum clock rate, four differential data inputs handling 28 bits per transfer, a rising-edge data-strobe architecture, and a +3.3 V supply. The device accepts shift clocks from 20 MHz through 85 MHz while maintaining a 50% duty cycle on the receiver output clock. Its 56-pin TSSOP package provides a standardized surface-mount footprint for high-speed interface designs. The differential signaling architecture reduces sensitivity to common-mode noise compared with single-ended interconnects. This makes the receiver appropriate for point-to-point links where data must cross a connector, cable, or noisy backplane region. The parallel output side converts the recovered data into logic-level signals for a controller, display, video pipeline, or data-capture system. Typical applications include industrial control links, video and imaging data transport, test-and-measurement equipment, instrumentation, and embedded systems that use the National Semiconductor Channel Link interface. It is normally paired with a compatible DS90CR287-family transmitter, with the link topology and support circuitry determined from the manufacturer datasheet. Layout is critical because the receiver must process small differential signals at clock rates as high as 85 MHz. Place the device close to the connector or cable termination, maintain symmetric routing between differential pairs, and provide the bypass capacitance specified by the manufacturer. Keep return-path current continuous and avoid routing data strobe signals across the differential inputs. This page consolidates interface specifications, lifecycle information, verified cross-references, and practical replacement guidance. It is intended to help engineers identify the correct receiver variant, evaluate equivalent parts, and plan a pin-compatible redesign without overlooking signal-integrity or board-layout constraints.