بەرهەمەکان (5,100+)

ADM232AARW - 200 kB/s Dual RS-232 Transceiver | Analog Devices
ADM232AARW

ADM232AARW - 200 kB/s Dual RS-232 Transceiver | Analog Devices

Analog Devices ADM232AARW is a 200 kB/s RS-232 interface transceiver integrating two drivers and two receivers for full-duplex serial communication. It operates from a single 5 V supply, uses four 0.1 µF charge-pump capacitors, and is packaged in a surface-mount 16-lead SOIC. The device also includes onboard DC-DC converter circuitry and provides approximately 9 V of transmitter output swing. An RS-232 transceiver is the interface bridge between a low-voltage digital controller and a physical serial port. The driver converts logic-level signals into RS-232-compatible levels, while the receiver converts bipolar RS-232 signals back into CMOS-compatible logic. As a member of the interface-IC hierarchy, the ADM232AARW belongs to the RS-232 transceiver class, where full-duplex operation, voltage levels, signaling rate, and supply voltage determine its system suitability. Key features include a 200 kB/s transmission rate, two drivers, two receivers, and receiver input protection to 30 V. The single 5 V supply allows operation from 4.5 V to 5.5 V, eliminating the need for a separate negative rail. The charge-pump network generates the positive and negative voltage levels required by RS-232, while the integrated DC-DC converter supports the on-board receive path. Its industrial temperature range extends from -40°C to +85°C. The ADM232AARW uses CMOS-compatible driver inputs and receiver outputs, making it suitable for UARTs, microcontrollers, modems, and industrial controllers with conventional 5 V or 3.3 V-compatible interface levels. Its 200 kB/s rate exceeds the throughput of many legacy serial links while retaining the familiar RS-232 electrical interface. The 16-SOIC package also supports automated board assembly and occupies substantially less board area than discrete driver and receiver implementations. Typical applications include industrial instrumentation, point-of-sale equipment, data acquisition systems, test equipment, and embedded control systems that exchange serial commands over an RS-232 port. It can also support legacy peripherals through short cables, although modern designs must consider ground continuity, protection, and the practical distance limitations of RS-232. Designers should place the four 0.1 µF charge-pump capacitors close to their assigned pins and route the serial outputs and inputs away from noisy switching circuitry. Input protection to 30 V improves tolerance to accidental voltage excursions, but it does not replace surge protection for cables exposed to industrial transients. This page combines the ADM232AARW's interface characteristics, verified drop-in references, package-level guidance, and practical comparison criteria to help engineers evaluate board compatibility and select the appropriate RS-232 transceiver.

RFQ پەیوەندی
ADM232AARWZ - 200 kB/s Dual RS-232 | Analog Devices
ADM232AARWZ

ADM232AARWZ - 200 kB/s Dual RS-232 | Analog Devices

The Analog Devices ADM232AARWZ is a dual, full RS-232 interface transceiver designed for data rates up to 200 kB/s. It operates from a single 5 V supply and uses a compact 0.1 µF external charge-pump capacitor arrangement. The device is offered in a 16-lead wide-body SOIC package and integrates two line drivers with two line receivers, making it suitable for bidirectional serial-port equipment. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts received RS-232 signals back into logic levels. It belongs to the interface IC hierarchy, alongside UART interface devices, level translators, and isolated communication transceivers. The ADM232A family is designed to simplify legacy and industrial serial connectivity without requiring a separate external negative supply. The principal features of the ADM232AARWZ include two transmit channels, two receive channels, operation from one 5 V supply, and transmission rates up to 200 kB/s. Its on-chip charge pump supports operation with small 0.1 µF external capacitors. The integrated receiver and driver arrangement reduces component count on boards that need more than one RS-232 connection. The 16-lead SOIC package is a standard surface-mount format suitable for conventional PCB assembly. The ADM232A is described by Analog Devices as a pin-compatible, high-speed upgrade for the AD232 and ADM232L families. This positioning makes it useful when a board requires faster serial throughput while retaining a familiar RS-232 transceiver architecture. Because it is a single-supply device, system designers can avoid a separate negative rail for the RS-232 interface, although external protection and signal-integrity components may still be required in long or electrically noisy installations. Typical uses include industrial serial adapters, instrumentation control ports, data-acquisition equipment, point-of-sale terminals, embedded service interfaces, and legacy peripheral connectivity. The dual-driver and dual-receiver organization allows one device to support two channels or to provide transmit and receive functions in one compact package. Its 200 kB/s capability is useful for moderate-speed command and control traffic rather than continuous high-throughput file transfer. PCB layout should keep charge-pump capacitors close to their designated pins, provide an uninterrupted ground reference, and keep the RS-232 driver outputs away from sensitive receiver and logic traces. External protection may be required for exposed cables because RS-232 is an unbalanced interface susceptible to electrostatic discharge and surge events. Confirm the complete pin assignment and recommended external-capacitor values against the manufacturer datasheet before releasing a PCB layout. This product page combines the ADM232A family architecture, verified distributor identification, package information, practical interface-circuit guidance, and clearly qualified replacement candidates. It is intended to help engineers identify the correct 16-lead SOIC variant and distinguish genuine footprint-compatible options from functional alternatives that require PCB changes.

RFQ پەیوەندی
ADM232LAN - 120 kbps Dual RS-232 Transceiver | Analog Devices
ADM232LAN

ADM232LAN - 120 kbps Dual RS-232 Transceiver | Analog Devices

Analog Devices ADM232LAN is a 2/2 RS-232 line-driver and receiver transceiver operating from a single 5 V supply, with a data rate of 120 kbps and a 16-pin through-hole DIP package. The device is intended for EIA-232-E and V.28 interfaces when conventional ±12 V supplies are unavailable. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar signaling used by RS-232 equipment. The ADM232LAN integrates two transmitters and two receivers, an onboard DC-to-DC converter, and charge-pump circuitry capable of producing approximately 9 V output swing from a 5 V supply. This places it in the interface IC hierarchy alongside RS-232 line drivers, receivers, and full-duplex communication transceivers. Key features include operation from one 5 V supply, 120 kbps data transmission, 1 µF external charge-pump capacitors, low-power shutdown, receiver operation during shutdown, and receiver input protection to 30 V. The dual 2/2 configuration allows two serial channels to be supported by one package. Its through-hole DIP construction is useful for legacy industrial control, instrumentation, test equipment, and system prototypes where surface-mount packages would be inconvenient. The ADM232LAN uses an on-chip DC-to-DC converter and charge pump to develop the positive and negative voltages required by RS-232 drivers. This topology avoids external ±12 V rails, although the external capacitors must be connected correctly and placed close to the device. The receiver converts incoming RS-232 voltage levels to CMOS-compatible logic, while each driver converts CMOS logic into RS-232 output levels. Typical uses include RS-232 ports in industrial controllers, laboratory instruments, barcode and data-acquisition equipment, configuration interfaces, and legacy computer peripherals. A two-channel implementation is especially useful where one port carries data and another carries control or status information. PCB design should reserve the documented charge-pump capacitor connections and provide adequate copper and grounding around the interface. Because the ADM232LAN is packaged in a 16-pin DIP, existing through-hole layouts may be easier to reuse than with a surface-mount alternative. Verify signal levels, capacitor values, grounding, and system shutdown behavior before substituting another RS-232 transceiver. This page combines verified distributor and datasheet-search information with practical interface-design guidance. It also distinguishes package-compatible alternatives from functionally similar devices that require different footprints or external-capacitor arrangements, helping engineers assess replacement risk before changing an RS-232 design.

RFQ پەیوەندی
ADM232LAR - 5V 2/2 RS-232 Transceiver, 120kB/s | Analog Devices
ADM232LAR

ADM232LAR - 5V 2/2 RS-232 Transceiver, 120kB/s | Analog Devices

The Analog Devices ADM232LAR is a 5 V-powered CMOS RS-232 line driver and receiver providing two drivers and two receivers (2/2) in a 16-lead SOIC package. It supports data rates up to 120 kB/s, meets all EIA-232-E and V.28 specifications, and delivers a 9 V output swing from a single 5 V supply. An RS-232 transceiver is an interface IC that translates logic-level CMOS signals into the bipolar, +/- voltage signalling used by the RS-232 (EIA-232) standard. It sits between a UART or microcontroller and a physical cable. The wider ADM2xx family of line drivers and receivers was designed for EIA-232-E and V.28 communications interfaces, especially where +/-12 V supplies are not available, and the ADM232 in particular adds on-board DC-DC converters so no external charge-pump components or negative supply are needed. Key features include a single 5 V power supply, on-board DC-DC converters with 9 V output swing capability, small 1 uF external capacitors, a low-power shutdown mode, 1 uA receiver operation while in shutdown, and receiver inputs tolerant to 30 V. The CMOS implementation keeps power consumption low compared with classic bipolar RS-232 transceivers. Technically, the part uses an on-chip switched-capacitor DC-DC converter to generate the positive and negative rail voltages required for compliant RS-232 output levels, while the receiver stage is designed for high noise immunity and failsafe operation when the driver is disabled or the line is unconnected. The result is full RS-232 compliance from a single rail, which simplifies board layout and reduces the external component count to a small number of 1 uF capacitors. Typical applications include industrial serial port adapters, instrumentation and test equipment, barcode and data-collection terminals, security and access-control panels, and general-purpose RS-232 links between a host UART and peripheral equipment where cable lengths and ground offsets require the +/- voltage swing of the RS-232 standard. When designing around the ADM232LAR, place the 1 uF capacitors close to the charge-pump and driver pins, keep the RS-232 connector and cable routing separated from sensitive analog and clock traces to limit EMI, and account for the shutdown pin when the host needs to tri-state or power down the port. Because the receivers remain active in shutdown, the interface can still report line state while the driver current is minimized. This page consolidates distributor listings, verified datasheet features, drop-in replacement options in the identical 16-SOIC footprint, and practical PCB and EMI design notes that are not assembled in one place in the original manufacturer documentation.

RFQ پەیوەندی
ADM232LJN - 5V RS-232 Transceiver | Analog Devices
ADM232LJN

ADM232LJN - 5V RS-232 Transceiver | Analog Devices

The Analog Devices ADM232LJN is a 5 V-powered CMOS RS-232 transceiver with two transmitters and two receivers, supplied in a 16-pin PDIP package. It supports 120 kB/s data rates, on-board DC-DC converters, approximately ±9 V output swing from a 5 V supply, 1 µF external capacitors, low-power shutdown, and receiver inputs that remain active during shutdown. According to the manufacturer product page, the ADM232L family is intended for EIA-232-E and V.28 communications interfaces where ±12 V is not available. An RS-232 transceiver is an interface IC that combines differential signal drivers and receivers for serial data communication over single-ended, bipolar RS-232 links. The transmitter converts logic-level signals into RS-232 levels, while the receiver converts bipolar RS-232 inputs back into CMOS-compatible logic levels. In the product hierarchy, an RS-232 transceiver is a line driver/receiver, a communications interface IC, and a semiconductor designed to bridge modern digital logic and older serial-interface equipment. The ADM232LJN combines a single 5 V supply with onboard charge-pump DC-DC converters, allowing the device to generate the bipolar voltage levels needed for RS-232 transmission without separate ±12 V rails. Its specified 120 kB/s data rate supports legacy serial ports, industrial equipment, and control systems. The approximately ±9 V output swing provides the required interface voltage amplitude while the CMOS implementation supports operation from one 5 V supply. The interface also includes low-power shutdown to reduce power dissipation when the link is not active. The receivers are specified as active in shutdown, allowing selected receive paths to remain operational during a low-power state. The use of small 1 µF capacitors makes the charge-pump and supply bypassing network relatively compact, which is useful in equipment where PCB area is constrained. Typical applications include legacy PC serial ports, industrial instrumentation, barcode scanners, test equipment, embedded control systems, and communications links to equipment designed for EIA-232-E or V.28 interfaces. The device is particularly useful where the system has a 5 V logic rail but the connected peripheral requires RS-232 signal levels. Designers should preserve the intended capacitor values, place charge-pump capacitors close to their specified pins, and route the RS-232 connector and cable interface away from sensitive analog or high-speed digital circuitry. The verified ADM232LJN data confirms a 16-pin PDIP package and a 120 kB/s data rate, but it does not provide a complete public pin-by-pin pinout or current distributor price table in the supplied material. This page consolidates the verified manufacturer and distributor information, separates confirmed specifications from unavailable data, and identifies a confirmed same-package family alternative. It also provides practical selection guidance for engineers choosing between single-supply RS-232 transceivers and legacy multi-rail implementations.

RFQ پەیوەندی
ADM232LJNZ - 5V Dual RS-232 Transceiver | Analog Devices
ADM232LJNZ

ADM232LJNZ - 5V Dual RS-232 Transceiver | Analog Devices

The Analog Devices ADM232LJNZ is a dual-driver, dual-receiver RS-232 transceiver that operates from a single 4.5 V to 5.5 V supply. It supports data rates up to 100 kbps and is packaged in a 16-pin PDIP package. The device converts logic-level transmit and receive signals to and from RS-232-compatible line levels, allowing a 5 V system to communicate with legacy serial equipment. An RS-232 transceiver is an interface integrated circuit within the broader communications-interface hierarchy. It combines line drivers, which translate CMOS logic into bipolar RS-232 signals, with receivers, which recover logic-level data from those signals. Because RS-232 uses voltage levels that can exceed the supply rails of modern CMOS logic, the onboard charge-pump circuitry generates the positive and negative voltages required on the bus. Key characteristics of the ADM232LJNZ include its 5 V CMOS-compatible supply, 100 kbps maximum signaling rate, two transmit channels, two receive channels, and EIA-232-E and V.28 interface support. The single-supply architecture eliminates the need for a separate negative rail at the device interface. Its through-hole PDIP package is also suitable for legacy industrial control boards, laboratory equipment, and instrumentation where leaded components are preferred. The ADM232L family was designed for communications interfaces where positive and negative 12 V rails are not available. Internally, the device combines transmit and receive functions in one package, reducing board area compared with separate driver and receiver ICs. External charge-pump capacitors are required, so the PCB layout must follow the manufacturer's recommended connection and grounding arrangement to achieve reliable operation and minimize transmitted noise. Typical applications include legacy PC serial-port interfaces, industrial control panels, barcode and label equipment, test instruments, and embedded systems that communicate with RS-232 printers, scanners, or data acquisition units. The dual-channel arrangement allows one port to transmit while the other receives, which is useful for bidirectional console links and device-control protocols. When designing around the ADM232LJNZ, connect the interface ground and signal ground carefully to minimize common-mode noise, place the charge-pump capacitors close to their assigned pins, and verify that every connected RS-232 port uses compatible signaling limits. The 100 kbps rate is suitable for moderate-speed control traffic, but it should not be selected for higher-bandwidth legacy serial links. This page combines manufacturer specifications, package information, interface-family comparisons, and application-oriented design guidance. It also identifies pin-compatible RS-232 transceiver alternatives that can support sourcing decisions where the original 16-pin PDIP footprint must be retained.

RFQ پەیوەندی
ADM232LJR - 5V 120kbps RS-232 Transceiver | Analog Devices
ADM232LJR

ADM232LJR - 5V 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices ADM232LJR is a 5 V powered RS-232 line-driver and receiver IC with two drivers, two receivers, a 120 kbps data rate, and a 16-pin SOIC package. It provides ±9 V output swing, onboard DC-DC converters, and 1 µF charge-pump capacitors, allowing EIA-232-E and V.28 communication without external ±12 V rails. The receiver remains active during shutdown according to the supplied manufacturer-family data. An RS-232 transceiver is an interface IC that converts logic-level signals into differential bipolar voltages for transmission and converts received bipolar voltages back into CMOS-compatible logic levels. In the product hierarchy, it belongs to the communications interface IC class, where it bridges a host controller or UART with a cable-based RS-232 port. Unlike RS-422 and RS-485 interfaces, RS-232 uses single-ended signaling referenced to ground and is primarily intended for point-to-point communication. The ADM232LJR operates from a single 5 V supply and supports data rates up to 120 kbps. Its integrated DC-DC converter generates the positive and negative voltage levels required by the EIA-232-E drivers without requiring an external dual supply. Other documented features include low-power shutdown, 1 µF external charge-pump capacitors, approximately ±9 V driver output swing from a 5 V supply, and receiver input protection rated to 30 V. The device contains two transmit channels and two receive channels, allowing two serial ports or one full-duplex port with flow-control signals to share one package. Its CMOS-compatible digital inputs connect directly to the transmit and shutdown-control circuitry of microcontrollers, DSPs, and embedded processors. The balanced set of receive and transmit functions supports protocol-handshake signals as well as primary data channels without requiring separate RS-232 line-driver ICs. Typical uses include industrial serial consoles, point-of-sale equipment, instrumentation, embedded control systems, and legacy peripheral connectivity. The 120 kbps rate comfortably supports many UART protocols and short-distance point-to-point links. Systems that previously used ±12 V RS-232 can simplify their power architecture by using one 5 V rail, provided the selected connector, cable, and protection network are suitable for the intended installation. Designers should use the manufacturer's recommended charge-pump capacitor values and observe polarity and voltage limits on all interface pins. The 30 V receiver-input rating does not permit unrestricted hot-plug or surge exposure, so external protection may still be required for exposed industrial cabling. The shutdown function should also be checked against the system requirement because the supplied family data states that the receivers remain active while the drivers are shut down. This page combines verified manufacturer and distributor information, package-aware replacement guidance, application engineering notes, and a specification comparison that are not consolidated on a typical distributor product listing. The alternatives are presented as candidates that still require schematic, pinout, and system-level verification before substitution.

RFQ پەیوەندی
ADM232LJRZ - 2/2 RS-232 Transceiver, 5V, 120kbps | Analog Devices
ADM232LJRZ

ADM232LJRZ - 2/2 RS-232 Transceiver, 5V, 120kbps | Analog Devices

The Analog Devices ADM232LJRZ is a 2/2 full-duplex RS-232 transceiver operating from a single 4.5 V to 5.5 V supply, with a maximum data rate of 120 kbps and ±9 V output swing from a 5 V supply. The device is packaged in a 16-pin SOIC for compact industrial, instrumentation, and embedded communication equipment. An RS-232 transceiver is an interface IC that combines line drivers and line receivers with the electrical conversion required by EIA-232 links. It belongs to the RS-232 interface IC hierarchy, where a dual driver converts logic-level transmit signals into bipolar RS-232 levels and two receivers convert incoming bipolar signals back into CMOS-compatible logic. This device is intended for systems where ±12 V is unavailable, using its on-board dc-to-dc converters to generate the required positive and negative voltage swings. Key characteristics include two transmitters, two receivers, a single 5 V supply, operation over a 4.5 V to 5.5 V input range, and a data rate of up to 120 kbps. The on-board converters produce approximately ±9 V output swing, while the charge-pump network uses small 1 µF capacitors. The interface is designed to meet EIA-232-E and V.28 requirements, making it appropriate for point-to-point serial links, instrumentation, data acquisition, and control systems. The ADM232L family combines CMOS power-efficient logic with bipolar RS-232 signal levels. Its integrated dc-to-dc converter avoids a separate negative supply and allows the interface to operate from one 5 V rail. Because the transmitter outputs are not TTL-compatible, downstream circuitry must use the transceiver's RS-232 output levels directly rather than driving the outputs from ordinary 5 V logic without proper translation. Typical applications include serial adapters, industrial control links, test and measurement equipment, embedded instrumentation, and communication ports that require two transmit and two receive channels. In a typical implementation, the device connects logic-level UART pins to an external DB9 or other RS-232 connector, while protection components handle electrostatic-discharge and cable-transient risks. When laying out the PCB, place the charge-pump capacitors and interface-side protection components close to the device. Keep RS-232 driver traces away from sensitive analog inputs, and provide a solid ground reference between the transceiver and connected equipment. Confirm connector-level fault protection and cable length against the system communication requirements.

RFQ پەیوەندی
ADM233LAN - 5V RS-232 Transceiver, 120kB/s | Analog Devices
ADM233LAN

ADM233LAN - 5V RS-232 Transceiver, 120kB/s | Analog Devices

The Analog Devices ADM233LAN is a 5 V RS-232 transceiver with two drivers and two receivers, a maximum data rate of 120 kB/s, and integrated DC-DC converters that produce ±9 V output swing from a single 5 V supply. The device is supplied in a 20-pin PDIP package and is intended for EIA-232-E and V.28 communications interfaces. An RS-232 transceiver is an interface IC that combines differential line-driver and receiver functions with the voltage conversion required by the EIA-232 standard. It belongs to the interface IC hierarchy, where an RS-232 transceiver operates between a digital logic circuit and a wired communications port. This is particularly useful when the equipment-side logic supply is 5 V but the RS-232 port requires positive and negative signal voltages. Key features include operation from one 5 V supply, support for data rates up to 120 kB/s, on-board DC-DC converters, ±9 V output swing, and operation with small 1 µF capacitors. The integrated charge-pump circuitry eliminates the need for a separate external power-supply circuit, reducing board area and simplifying serial-interface implementation. Technically, the ADM233LAN is a 2/2 full RS-232 transceiver: two transmitter channels and two receiver channels are provided in one package. Its on-board converters generate the bipolar voltage levels required by RS-232 while the device interfaces with conventional 5 V CMOS logic. This integration is valuable in compact industrial, instrumentation, and embedded systems where component count and PCB area are constrained. Typical uses include RS-232 test equipment, data-acquisition systems, industrial control links, service interfaces, and legacy peripheral connections. In these applications, the device can translate 5 V TTL or CMOS UART signals to and from the bipolar RS-232 interface. Designers should still include appropriate line protection and verify signal-integrity requirements in long or electrically noisy installations. A primary design consideration is charge-pump capacitor selection and placement. The manufacturer documentation specifically highlights small 1 µF capacitors, and these components should be placed close to the associated device pins to minimize loop area and preserve stable converter operation. Decoupling, grounding, and protection requirements should be implemented according to the manufacturer datasheet. This page consolidates the verified manufacturer and distributor information with a pin-compatible family alternative, parameter comparison, application guidance, and practical interface-design notes. It distinguishes documented electrical facts from parameters that require confirmation in the current manufacturer datasheet or distributor inventory record.

RFQ پەیوەندی
ADM233LJN - 2/2 RS-232, 5V, 120kbps | Analog Devices
ADM233LJN

ADM233LJN - 2/2 RS-232, 5V, 120kbps | Analog Devices

The Analog Devices ADM233LJN is a 5 V-powered CMOS RS-232 transceiver with two drivers and two receivers, a 120 kbit/s data rate, and a 20-pin PDIP package. Its integrated DC-DC converter produces approximately ±9 V output swing from a single 5 V supply, while its small 1 µF charge-pump capacitors simplify implementation of EIA-232-E and V.28 interfaces. An RS-232 transceiver is an interface IC that converts logic-level digital signals into differential bipolar transmission signals and converts received bipolar signals back into CMOS logic levels. The ADM233LJN belongs to the RS-232 transceiver category, where it bridges the gap between low-voltage digital systems and the voltage-tolerant, ground-referenced communication interface historically defined by RS-232. Key features include one 5 V supply, two driver and two receiver channels, operation at 120 kbit/s, onboard DC-DC conversion, ±9 V output swing, low-power shutdown, and 1 µF external charge-pump capacitors. The receiver input withstands voltages up to 30 V, while shutdown keeps the receivers active, allowing a connected system to retain incoming data during a local transmitter shutdown. The integrated charge-pump architecture eliminates the need for a separate ±12 V supply and reduces external component count compared with conventional RS-232 implementations. The transmitter actively drives the RS-232 signal levels, while the receiver provides noise tolerance and level translation for incoming data. This makes the device suitable for equipment in which a modern 5 V logic supply is available but a legacy computer serial port is not. Typical applications include industrial serial adapters, point-of-sale terminals, instrumentation, barcode scanners, security equipment, and embedded control systems. The ADM233LJN is particularly useful when a PCB must implement a full RS-232 port using only a 5 V rail and through-hole assembly, while its integrated converters reduce the external power-tree complexity. Designers should verify the external charge-pump capacitor values, connector protection, and ground arrangement against the manufacturer datasheet. Although the receiver tolerates inputs up to 30 V, exposed RS-232 connectors should receive appropriate surge and electrostatic-discharge protection. Decoupling and charge-pump capacitor placement also require careful PCB layout to minimize switching noise and data errors. This page combines verified manufacturer specifications, current sourcing information, drop-in replacement analysis, and practical application guidance. It also distinguishes verified electrical differences from unknown parameters so engineers can assess PCB, regulatory, and lifecycle implications before committing to a design.

RFQ پەیوەندی
ADM233LJNZ - 120kbps RS-232 Transceiver | Analog Devices
ADM233LJNZ

ADM233LJNZ - 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices ADM233LJNZ is a single-chip, 2/2 RS-232 line transceiver operating from one 5 V supply, with a maximum data rate of 120 kbps in a 20-pin PDIP package. It includes two RS-232 drivers, two RS-232 receivers, on-board DC-DC converters, and approximately ±9 V output swing for reliable single-ended EIA-232-E and V.28 communications. A line transceiver is an interface circuit that translates logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into digital logic levels. Within the interface hierarchy, it belongs to the RS-232 transceiver family of communication ICs, where it bridges modern controller logic and legacy point-to-point serial equipment. The ADM233L is particularly useful when a system cannot provide the traditional ±12 V RS-232 supply. The integrated DC-DC conversion system produces the bipolar voltages required by RS-232 from a single 5 V rail, eliminating the need for external charge-pump components. The device supports 120 kbps signaling, provides two transmit channels and two receive channels, and uses small 1 µF external capacitors as stated by Analog Devices. Its dual-driver, dual-receiver arrangement makes it suitable for links requiring one bidirectional channel plus one additional direction, or for a design that can be configured differently around the two driver and receiver sections. The ADM233L is intended for EIA-232-E and V.28 interfaces where 12 V is unavailable. Its single-supply architecture simplifies power distribution while retaining the voltage levels expected by RS-232 equipment. Because RS-232 is a single-ended, unbalanced interface, board layout should keep the driver outputs and receiver inputs away from sensitive analog and high-speed digital traces. The transmitter and receiver functions should also be routed so outgoing and incoming signals do not unnecessarily share long parallel paths. Typical uses include industrial serial-control links, data-acquisition equipment, service interfaces, test systems, and embedded controllers communicating with RS-232 peripherals. The 120 kbps rate is appropriate for configuration commands, telemetry, firmware transfer, and general-purpose serial control where longer distances and noise immunity are more important than very high throughput. A null modem or crossover arrangement is still required when connecting two similarly configured data-terminal devices. The principal design consideration is decoupling and signal integrity. Place the specified 1 µF capacitors close to their associated pins, provide a stable 5 V supply, and route each RS-232 signal as a direct point-to-point channel. Avoid long unprotected traces adjacent to switching nodes or high-current return paths. For industrial equipment, verify the complete board against the applicable EMC requirements and provide appropriate chassis grounding at the connector rather than relying on the logic ground alone. This product overview combines the confirmed ADM233LJNZ electrical features, package details, interface standards, and practical RS-232 layout guidance with drop-in comparison information intended to accelerate component selection and PCB redesign planning.

RFQ پەیوەندی
ADM234LAN - 5V RS-232 Driver/Receiver | Analog Devices
ADM234LAN

ADM234LAN - 5V RS-232 Driver/Receiver | Analog Devices

The Analog Devices ADM234LAN is a 5 V-powered CMOS RS-232 driver and receiver IC with four driver channels and four receiver channels in a 16-pin PDIP package. It supports EIA-232-E and V.28 communications interfaces without requiring external ±12 V supplies. Verified data identifies a 120 kB/s data rate, on-board DC-DC converters, 9 V output swing from a 5 V supply, low-power shutdown, 1 A receiver inputs, and receiver inputs that remain active during shutdown. A line transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into CMOS-compatible logic. The ADM234LAN belongs to the line-driver and receiver hierarchy, within interface transceivers and communications interface ICs. Its integrated charge-pump and DC-DC circuitry allows a single-ended 5 V supply to generate the positive and negative voltage levels required by a conventional RS-232 port. The four transmitters and four receivers make the ADM234LAN suitable for implementing a complete multi-channel RS-232 interface on one integrated circuit. Its 120 kB/s rated data rate supports legacy serial links, industrial equipment, data-acquisition systems, and control equipment that use EIA-232-E or V.28 signaling. The 9 V output swing provides the voltage amplitude needed by RS-232 while the receiver section handles signals arriving from a cable-connected remote device. The device includes low-power shutdown control and receiver behavior designed to remain operational while the rest of the interface is shut down. That feature can simplify asynchronous serial designs in which one channel must monitor a remote link while the remaining transmitter and receiver functions are inactive. The receiver input also withstands 30 V, increasing tolerance to transients and voltage levels encountered on external RS-232 connections. The ADM234LAN is supplied in a 16-pin PDIP package, making it appropriate for legacy through-hole boards, prototypes, and industrial control systems that use conventional DIP footprints. Designers should provide the required external capacitors, route the interface connector and cable ground appropriately, and verify every signal pin against the current manufacturer datasheet before production use. For a new design, the ADM234LAN offers a practical way to add RS-232 capability from one 5 V rail without implementing an external switched-capacitor inverter. Its tradeoff is the relatively slow 120 kB/s data rate compared with USB, LVDS, or modern high-speed differential interfaces. The ADM234LAN is therefore most appropriate where protocol compatibility and legacy EIA-232-E or V.28 support matter more than throughput.

RFQ پەیوەندی
ADM234LANZ - 100kbps Quad RS-232 Driver | Analog Devices
ADM234LANZ

ADM234LANZ - 100kbps Quad RS-232 Driver | Analog Devices

The Analog Devices ADM234LANZ is a four-channel CMOS RS-232 line driver operating from a single 4.5 V to 5.5 V supply, supporting data rates up to 100 kbps in a 16-pin PDIP package. Designed for EIA-232-E and V.28 communications interfaces, it eliminates the need for external ±12 V supplies in systems where only a +5 V rail is available. The device uses a charge-pump architecture to generate the bipolar voltage levels required by RS-232 transmitters. An RS-232 line driver is a communications interface integrated circuit that converts logic-level signals from a host, controller, or data-acquisition system into bipolar voltage levels suitable for transmission over a serial link. It belongs to the interface IC hierarchy, specifically the line-driver and transceiver class used to bridge digital logic and legacy serial communication ports. The ADM234LANZ provides four driver channels, a maximum supply voltage of 5.5 V, CMOS technology, and a 100 kbps maximum data rate. Its industrial temperature grade supports use in factory automation, industrial controls, instrumentation, and embedded equipment where RS-232 compatibility must coexist with a modern single-supply architecture. The through-hole PDIP package also favors repairable industrial assemblies and designs assembled with conventional DIP sockets. Each driver channel provides the electrical voltage translation required for RS-232 signaling, while the integrated charge-pump circuitry generates the positive and negative transmitter levels from the +5 V supply. This architecture reduces the external component count compared with a discrete RS-232 implementation and avoids separate power rails for the interface. Designers should still treat the driver outputs as differential-voltage, bipolar signaling nodes rather than ordinary CMOS logic outputs. Typical applications include RS-232 links in industrial controllers, laboratory instruments, barcode and test equipment, legacy data-collection systems, and service interfaces for embedded machinery. The device is particularly suitable when a modern controller has a 5 V UART but the peripheral connection still requires EIA-232-E levels. Its four channels support several independent transmit paths where the system needs more than one serial endpoint. For reliable implementation, place the driver close to the connector or protected board edge, route each RS-232 output as a differential pair, and provide the supply and ground connections required by the Analog Devices datasheet. Add appropriate surge and ESD protection when the cable leaves the enclosure, and account for the non-inverting logic thresholds and slew behavior when designing system-level timing. This page consolidates the exact ADM234LANZ electrical ratings, verified package information, sourcing guidance, cross-reference findings, and practical implementation considerations. It also distinguishes ordering and package variants from true pin-compatible replacements so engineers can make a controlled substitution without assuming that every similar RS-232 part is electrically identical.

RFQ پەیوەندی
ADM234LAQ 5V RS-232 Driver/Receiver | Analog Devices
ADM234LAQ

ADM234LAQ 5V RS-232 Driver/Receiver | Analog Devices

The Analog Devices ADM234LAQ is a 5 V powered CMOS RS-232 driver and receiver interface IC with integrated DC-DC converters, 120 kB/s data-rate capability, and low-power shutdown support. The device is designed for single-supply systems that require RS-232 communication without a separate negative supply. The ADM234LAQ provides four drivers and four receivers in a 16-pin package, making it suitable for industrial control, instrumentation, data acquisition, and embedded equipment interfaces. An RS-232 interface IC is a signal-conditioning device that converts logic-level digital signals into RS-232-compatible levels and converts incoming RS-232 signals back into CMOS logic levels. The RS-232 standard is widely used for point-to-point serial links in industrial equipment, test systems, and legacy computer peripherals. The ADM234LAQ belongs to the interface-IC hierarchy, where transceivers combine drivers, receivers, and the voltage-conversion functions required by the RS-232 electrical specification. The ADM234LAQ operates from a single 5 V supply and includes on-board DC-DC converters that generate the negative voltage needed by an RS-232 line driver. The on-board converters reduce external power-supply complexity while allowing the device to meet RS-232 output-swing requirements from a 5 V source. Its CMOS implementation supports low-power operation and includes a shutdown function for systems where the interface must be disabled during inactive periods. The device supports data rates up to 120 kB/s, making it appropriate for standard RS-232 links rather than high-speed differential protocols. Its receiver section is designed to reject noise and withstand the voltage range commonly encountered on RS-232 connections. The integrated four-driver and four-receiver organization supports multiple serial ports or separate control and data channels in one package. Typical applications include industrial PLC and sensor interfaces, laboratory measurement equipment, barcode and scanner connections, service-console links, and embedded control boards. The single 5 V architecture is particularly useful when the host system does not provide a negative analog rail. The shutdown input can reduce system power when a port is not communicating, while the receiver remains active during shutdown according to the device features described by the manufacturer. Designers should pay close attention to line-driver load, cable length, grounding, and logic-level compatibility. The RS-232 interface is point-to-point, and cable capacitance or excessive loading can reduce the usable data rate. Place the device close to the connector when practical, provide a low-impedance ground connection, and verify that the host UART voltage levels match the CMOS logic inputs and outputs. The integrated DC-DC architecture should be evaluated against the application’s noise requirements, particularly near sensitive analog measurement circuits.

RFQ پەیوەندی
ADM234LAR - 4/4 5V RS-232 Interface | Analog Devices
ADM234LAR

ADM234LAR - 4/4 5V RS-232 Interface | Analog Devices

The Analog Devices ADM234LAR is a 5 V-powered CMOS RS-232 interface IC containing four drivers and four receivers, supporting data rates up to 120 kB/s in a 20-lead SSOP package. It is designed for single-supply equipment that must communicate with legacy RS-232 ports using EIA-232-E and V.28-compatible signaling. An RS-232 interface IC is a transceiver within the broader interface-IC and data-communication semiconductor hierarchy. It converts low-voltage CMOS logic into RS-232-compatible line levels and converts incoming RS-232 signals back into CMOS logic. The ADM234LAR integrates this bidirectional conversion so a system can connect a UART, microcomputer, or embedded controller to a serial port without implementing discrete charge-pump and level-shifting circuits on the PCB. Key features include a single 5 V power supply, 120 kB/s data rate, onboard DC-DC converters, approximately 9 V output swing from a 5 V supply, and support for 1 µF charge-pump capacitors. Low-power shutdown is also listed, while the receivers remain active during shutdown. A 30 V receiver-input rating provides additional tolerance for exposed serial connections. The integrated DC-DC converter allows the drivers to generate the positive and negative voltage swings required by RS-232 without a negative supply rail. This simplifies system power architecture, although external charge-pump capacitor selection, layout, and ripple behavior remain important. The four-driver/four-receiver arrangement consolidates multiple serial channels in one package and can reduce board area when compared with separate single-channel transceivers. Typical applications include industrial serial controllers, data-logging equipment, instrumentation, point-of-sale systems, embedded control panels, and legacy peripheral connectivity. The ADM234LAR is particularly useful where the host logic operates from 5 V but the external cable interface requires bipolar RS-232 levels. Designers must still account for cable length, common-mode voltage, ground noise, and protection requirements. The principal layout consideration is keeping charge-pump and high-voltage driver paths compact while maintaining adequate separation from sensitive logic. Place the specified capacitors close to their associated pins, use a low-inductance ground return, and route protected connector-side traces away from clocks, analog inputs, and precision references. A solid ground plane and short return path help reduce RS-232 return-current effects. This product page combines the verified ADM234LAR feature data with package guidance, application analysis, comparison criteria, and design notes. Because verified pricing, exact pin functions, operating-temperature limits, and several electrical limits were not included in the supplied records, those fields are marked for confirmation rather than inferred from unrelated parts.

RFQ پەیوەندی
ADM234LJNZ - 4/0 Low-Power RS-232 Driver | Analog Devices
ADM234LJNZ

ADM234LJNZ - 4/0 Low-Power RS-232 Driver | Analog Devices

The Analog Devices ADM234LJNZ is a low-power +5 V CMOS RS-232 line driver with four driver channels and no receiver channels, specified for data rates up to 100 kBPS and supplied in a 16-pin PDIP package. Its operating supply range is 4.5 V to 5.5 V, and the commercial temperature grade covers standard industrial and instrument applications. An RS-232 driver is a differential line-interface circuit that converts CMOS logic-level inputs into the bipolar voltage levels used by the RS-232 standard. The ADM234LJNZ belongs to the broader interface IC category, specifically the RS-232 driver and receiver family. Unlike a complete RS-232 transceiver, this device provides four transmit channels only, making it useful when the receiving function is implemented elsewhere or when four independent outbound ports are required. Key features include four RS-232 drivers, a 4.5 V to 5.5 V supply range, operation up to 100 kBPS, and low-power CMOS implementation. The device is designed for systems that cannot provide the traditional plus-or-minus 12 V RS-232 supply. Its CMOS input structure allows direct connection to 5 V digital control logic while internal charge-pump circuitry produces the required bipolar output levels. The 16-pin PDIP package favors through-hole assembly and repairable industrial equipment. Because the ADM234LJNZ is a transmitter-only device, it cannot directly receive RS-232 signals. Designers should therefore verify the companion receiver, connector protection, cable routing, and grounding strategy before releasing a PCB layout. Typical applications include industrial control panels, test and measurement instruments, embedded serial ports, point-of-sale equipment, and multi-port RS-232 expansion boards. The 100 kBPS maximum data rate is more than adequate for legacy serial peripherals, instrument control, configuration links, and short-distance point-to-point communication. For PCB implementation, place the device close to the RS-232 connector, keep driver traces short, and provide suitable transient protection on exposed serial lines. Confirm that the selected connector and cable arrangement support the intended signaling distance, and verify the logic levels and data-rate margin of the connected peripheral. This page summarizes the manufacturer product information, distributor listings, technical attributes, and practical integration considerations for engineers evaluating the ADM234LJNZ in a new RS-232 interface design.

RFQ پەیوەندی
ADM234LJR - 5V CMOS RS-232 Drivers/Receivers | Analog Devices
ADM234LJR

ADM234LJR - 5V CMOS RS-232 Drivers/Receivers | Analog Devices

The Analog Devices ADM234LJR is a 5 V-powered CMOS RS-232 line driver and receiver integrated circuit designed for EIA-232-E and V.28 communication interfaces. It provides four drivers and four receivers in a 16-lead SOIC package, supporting operation from a single 5 V supply while producing approximately 9 V RS-232 output swing. The device includes on-board DC-DC converters, allowing ±12 V RS-232-level signaling without an external dual supply. According to the manufacturer datasheet, the interface supports data rates up to 120 kB/s, includes low-power shutdown, and provides approximately 1 F charge-pump capacitors. The ADM234LJR is suitable for industrial equipment, instrumentation, data acquisition, and embedded serial links where a single 5 V rail must connect to an RS-232 transceiver port. Its CMOS implementation targets low power consumption and compact PCB area compared with discrete RS-232 interface designs. The 16-pin SOIC package is available in commercial temperature-grade product ordering and is identified by the ADM234LJR part number. Designers should account for RS-232 cable length, signal polarity, grounding, and the voltage limits of the connected equipment when deploying this interface. The internal charge-pump architecture simplifies the power-supply arrangement, but external bypass and charge-pump capacitors remain necessary according to the datasheet application guidance.

RFQ پەیوەندی
ADM235LJN - 5V RS-232 Transceiver | Analog Devices
ADM235LJN

ADM235LJN - 5V RS-232 Transceiver | Analog Devices

The Analog Devices ADM235LJN is a single-supply CMOS RS-232 line driver and receiver with a 5 V power supply, 120 kB/s data rate, and onboard DC-DC converters. The integrated converters produce a 9 V output swing without requiring external ±12 V supplies, while the device is housed in a 24-pin PDIP package measuring 0.600 inch, or 15.24 mm, across the lead span. An RS-232 transceiver is an interface IC that combines a transmitter and receiver for serial data links using differential voltage signaling. It belongs to the RS-232 line transceiver and interface IC hierarchy, where EIA-232-E and V.28 define the electrical behavior expected by compatible computer and industrial equipment. The ADM235LJN is intended for systems that need an RS-232 port but cannot conveniently provide both positive and negative supply rails. Key features include operation from one 5 V supply, onboard DC-DC conversion, 120 kB/s data throughput, a 9 V output swing, and support for low-power shutdown. The receivers remain active during shutdown and tolerate input voltages to 30 V. These characteristics make the device useful when an existing embedded system must deliver conventional RS-232 levels from a single low-voltage rail. The internal charge-pump and DC-DC circuitry eliminates the external negative supply normally associated with older RS-232 implementations. A 9 V output swing provides useful margin against the RS-232 voltage thresholds, while the 30 V receiver input rating helps protect the interface when connected to exposed or longer cables. Receiver and driver performance should still be evaluated against the system’s grounding and noise environment. Typical applications include industrial control consoles, POS terminals, service equipment, data acquisition systems, and embedded instrumentation. The device is especially appropriate where a 5 V logic rail is available but a separate negative voltage rail would increase power-supply complexity or reduce reliability. Cable length and data rate must be considered when designing the physical link. For implementation, place the device close to the RS-232 connector and keep the unprotected transceiver-side traces away from sensitive analog and high-speed digital signals. Verify bypass-capacitor placement and grounding against the manufacturer application guidance. The 24-pin PDIP format favors through-hole assembly and prototype or industrial equipment where a socket or leaded component is appropriate. This page organizes the electrical capabilities, interface use cases, comparison points, and implementation considerations of the ADM235LJN. It also distinguishes true package-level replacement options from related RS-232 devices that require different supplies, different packages, or different interface functions.

RFQ پەیوەندی
ADM236LAN - 5V 4/3 RS-232 Transceiver | Analog Devices
ADM236LAN

ADM236LAN - 5V 4/3 RS-232 Transceiver | Analog Devices

Analog Devices ADM236LAN is a 5 V powered CMOS RS-232 interface transceiver with four drivers, three receivers, 120 kB/s data rate, and on-board DC-DC converters in a 24-pin PDIP package. The single-supply design produces a 9 V output swing from a 5 V supply, while small 1 F capacitors support the on-board converters. Low-power shutdown keeps the receivers active, and the receiver inputs tolerate voltages up to 30 V. A CMOS RS-232 transceiver is an interface IC that converts digital logic levels into RS-232 line levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy, where transceiver ICs bridge low-voltage digital systems and older, high-voltage serial interfaces. The ADM236LAN combines transmit and receive functions in one device, reducing the number of separate line-interface components required by an RS-232 port. Key features include compliance with EIA-232-E and V.28 specifications, operation from one 5 V supply, a 120 kB/s maximum data rate, and four transmitters with three receivers. The integrated DC-DC converters eliminate the need for a separate negative supply rail and permit approximately 9 V output swing. The shutdown function reduces power use when the interface is inactive, while the always-active receivers can continue detecting incoming data. The device uses CMOS drivers and receivers to combine RS-232 signal conditioning with modern low-power logic interfacing. Its 1 F charge-pump capacitors support the on-board converters, and the 30 V receiver input rating provides margin for exposed serial ports. Designers should still protect the driver outputs against sustained overvoltage, electrostatic discharge, and uncontrolled cable transients according to the system-level requirements. Typical uses include industrial equipment, laboratory instruments, data acquisition systems, legacy controller ports, configuration interfaces, and service equipment requiring a compact RS-232 connection. The four-driver capability allows multi-channel arrangements, while three receiver channels support monitoring or handshake signals. It is particularly useful where a modern controller must communicate with equipment that retains an RS-232 interface. A key design consideration is that the ADM236LAN operates from 5 V, but its RS-232 driver outputs still use elevated voltage levels generated internally. Place the 1 F converter capacitors and interface-protection components close to their associated pins, keep the converter loop compact, and provide suitable return paths for high-current driver transitions. This page consolidates verified manufacturer and distributor information, same-package alternatives, technical comparisons, and practical integration guidance. It also distinguishes documented electrical characteristics from parameters that require confirmation against the current Analog Devices datasheet before a new design is released.

RFQ پەیوەندی
ADM236LJN - 4/3 5V RS-232 Transceiver | Analog Devices
ADM236LJN

ADM236LJN - 4/3 5V RS-232 Transceiver | Analog Devices

Analog Devices ADM236LJN is a 4-driver, 3-receiver CMOS RS-232 interface transceiver operating from a single 5 V supply at data rates up to 120 kB/s, housed in a 24-pin DIP package. The integrated DC-DC converter produces approximately 9 V signal swings without requiring external ±12 V rails, while onboard 1 uF charge-pump capacitors simplify the application circuit. A CMOS RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible voltage levels and converts received RS-232 signals back into logic levels. In the interface hierarchy, it belongs to the RS-232 transceiver category, then to communications interface ICs, then to broader interface and semiconductor families. It is useful wherever two systems must exchange serial data across a noise-prone, unbalanced cable using the EIA-232-E and V.28 signaling specifications. Key features include a single 5 V power supply, four drivers, three receivers, a maximum data rate of 120 kB/s, an approximately 9 V output swing, and receiver input levels extending to 30 V. Low-power shutdown is supported, and the receivers remain active in shutdown according to the supplied family data. The interface also offers ESD protection greater than 2 kV and is described as latch-up free. The ADM236L family uses onboard charge-pump circuitry to generate the bipolar voltage required by RS-232 drivers from a single positive supply. This architecture removes the external ±12 V requirement common to older RS-232 implementations. A 4-to-3 driver and receiver arrangement suits asymmetric links, including systems that transmit on several lines but receive data on a smaller number of channels. Typical uses include industrial control links, point-of-sale equipment, instrumentation, data acquisition, and embedded serial ports where a 5 V system cannot provide ±12 V. The 120 kB/s capability is suitable for moderate-speed control and data-transfer channels rather than high-bandwidth protocols. Its DIP-24 package is also appropriate for through-hole legacy and industrial boards. Designers should provide the datasheet-specified 1 uF capacitors, route the charge-pump and interface connections according to the manufacturer's application guidance, and keep RS-232 routing away from sensitive analog signals. Confirm supply tolerance, transceiver direction, and connector-level protection against the actual board requirements before production use. This page combines verified manufacturer-family specifications, distributor availability information, structured comparison data, and practical integration guidance. It distinguishes package-level replacement constraints from merely similar RS-232 devices, helping engineers avoid substitutions that require pinout, channel-count, or board-layout changes.

RFQ پەیوەندی
ADM236LJR - 5V 120kbps RS-232 Transceiver | Analog Devices
ADM236LJR

ADM236LJR - 5V 120kbps RS-232 Transceiver | Analog Devices

Analog Devices ADM236LJR is a +5 V powered CMOS RS-232 drivers/receivers interface IC with a 120 kB/s data rate, 9 V output swing, and a 20-pin SOIC package. It integrates three drivers and three receivers with on-board DC-DC converters, allowing EIA-232-E and V.28 communications from a single 5 V supply without external +12 V and -12 V rails. The device also supports low-power shutdown below 5 µW and provides small 1 µF charge-pump capacitors. An RS-232 transceiver is an interface IC that combines line drivers, line receivers, and voltage-level translation for serial communications. In the product hierarchy, it belongs to interface ICs, data converters and interface devices, and semiconductor components. The ADM2xx family is intended for systems where conventional negative supply voltages are unavailable. The integrated converter approach reduces board complexity by producing bipolar RS-232 levels internally while the external system operates from 5 V. Key features include a maximum stated data rate of 120 kB/s, on-board DC-DC conversion, approximately 9 V output swing from a 5 V supply, and 1 µF external charge-pump capacitors. The low-power shutdown function reduces power dissipation to less than 5 µW, making the interface suitable for portable and power-conscious equipment. Two receivers remain active during shutdown, allowing selected incoming signals to be monitored while most of the transceiver is inactive. The receiver input withstands voltages up to 30 V, providing protection in industrial environments where connected equipment can present larger voltage excursions. The manufacturer datasheet also states that the drivers maintain approximately ±5 V signal levels at data rates up to 100 kbps under worst-case loading. These characteristics make the ADM236LJR useful where a compact, single-supply RS-232 connection is required without relying on an external bipolar power supply. Typical applications include industrial serial-port equipment, point-of-sale terminals, data acquisition systems, test and measurement instruments, security-system controllers, and battery-powered communication equipment. Designers should verify line capacitance, cable length, driver loading, and receiver input levels against the application’s EIA-232-E requirements. The shutdown-control logic and the behavior of the two always-active receivers should also be checked to ensure they meet the system power-management sequence. For a robust layout, place the 1 µF charge-pump capacitors close to their associated IC pins and keep the high-voltage driver outputs away from sensitive input traces. Confirm that the external supply remains stable during data transmission, and account for the positive temperature coefficient of RS-232 thresholds when designing across the full operating environment. The exact pin names, package dimensions, and full electrical limits should be confirmed against the official Analog Devices datasheet before layout release. This page combines the verified Analog Devices datasheet information, current distributor availability, same-package alternatives, and practical design guidance. It highlights the ADM236LJR’s single-supply operation, integrated DC-DC conversion, shutdown behavior, and interface trade-offs in a format intended for component selection and PCB design decisions.

RFQ پەیوەندی
ADM237LAN - 5V 5/3 RS-232 Transceiver | Analog Devices
ADM237LAN

ADM237LAN - 5V 5/3 RS-232 Transceiver | Analog Devices

The Analog Devices ADM237LAN is a 5 V powered CMOS RS-232 transceiver with five drivers and three receivers, housed in a 24-pin plastic dual-inline package. It supports data rates up to 120 kB/s, meets EIA-232-E and V.28 interface requirements, provides 9 V output swing from a 5 V supply, and includes onboard DC-DC converters for single-supply operation. An RS-232 transceiver is a semiconductor interface device that combines line drivers and receivers for point-to-point serial data links. The transmitter converts logic-level signals into RS-232 voltage levels, while the receiver converts bipolar RS-232 signals back into logic-level voltages. The ADM237LAN belongs to the interface IC hierarchy as a communication transceiver and provides the electrical conversion required between CMOS systems and the EIA-232-E signal interface. The five-driver and three-receiver arrangement supports equipment with more transmit channels than receive channels. Onboard DC-DC converters allow the driver outputs to achieve a 9 V swing from one 5 V supply, reducing the external power-supply count in compact serial interfaces. The device also includes low-power shutdown, receiver activity during shutdown, and small 1 F capacitors as highlighted in the indexed datasheet information. RS-232 receivers in the ADM237LAN support input voltages up to 30 V. This tolerance helps protect receiver inputs when connected to an RS-232 port that may experience transients or voltage offsets. The CMOS implementation operates from a single 5 V supply and is intended for EIA-232-E and V.28 communications interfaces, including applications where a separate 12 V rail is unavailable. Typical uses include industrial control consoles, data acquisition equipment, test instruments, service interfaces, and embedded serial ports. Designers can use the ADM237LAN to bridge a 5 V controller to an RS-232 host while retaining a 120 kB/s communication rate. In multi-port systems, the asymmetric channel count should be matched to the actual cable directions and loading requirements of each port. The primary design consideration is ensuring that every driver and receiver has a defined signal path. Place the specified charge-pump capacitors close to their associated pins, route the interface connector and cable return path to minimize noise pickup, and use the receiver tolerance rating only as protection margin rather than as a substitute for correct RS-232 voltage levels. This page organizes the ADM237LAN's core interface, electrical, package, and lifecycle information with practical application guidance, shutdown considerations, and a validation-conscious replacement workflow. It also distinguishes confirmed product characteristics from parameters that require confirmation before a new PCB layout or production release.

RFQ پەیوەندی
ADM237LAQ - 5V RS-232 Transceiver | Analog Devices
ADM237LAQ

ADM237LAQ - 5V RS-232 Transceiver | Analog Devices

The Analog Devices ADM237LAQ is a 5 V powered CMOS RS-232 drivers and receivers IC packaged in a 24-pin ceramic DIP. It supports data rates up to 120 kB/s, provides an on-board DC-DC converter for 9 V output swing, and uses 1 uF capacitors for charge-pump operation. The device also includes low-power shutdown, receivers that remain active in shutdown, and receiver inputs rated to 30 V. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a peripheral using the RS-232 electrical standard. Its transmitter translates CMOS logic into RS-232-compatible levels, while its receiver converts the bipolar serial signal back into CMOS logic. Within the interface hierarchy, the ADM237LAQ belongs to the RS-232 transceiver class of interface ICs used for robust point-to-point serial data links. Key features include a single 5 V supply, compliance with the EIA-232-E and V.28 specifications listed in the manufacturer datasheet, operation at 120 kB/s, and a 9 V output swing generated by the internal DC-DC converter. Small 1 uF charge-pump capacitors reduce board-area requirements. A shutdown function supports power-sensitive systems, while active-in-shutdown receivers can monitor a remote link when the main transmitter circuitry is disabled. The ADM237LAQ combines multiple drivers and receivers with internal charge-pump circuitry, allowing a compact implementation of an RS-232 port without external level-shifting transistors. Its CMOS implementation is intended for low-power logic systems operating from 5 V. The internal voltage conversion allows the transmitters to produce RS-232-level voltages from the single 5 V supply, reducing the number of external power rails required by the host system. Typical applications include industrial control links, test equipment, instrumentation, data-acquisition systems, and embedded serial ports. The device is particularly useful where a legacy RS-232 interface must coexist with modern 5 V CMOS logic and where a regulated 5 V supply is available but a separate RS-232 supply is undesirable. The 24-pin ceramic DIP format is suited to through-hole industrial and legacy-system assemblies rather than compact surface-mount designs. When designing around the ADM237LAQ, place the 1 uF charge-pump capacitors close to their specified pins and route the interface connector and cable ground correctly because RS-232 is a single-ended, bipolar standard. Confirm signal levels and timing at the receiver before assuming a modern serial controller can connect directly. The ceramic DIP package also requires adequate through-hole spacing and appropriate assembly clearances. This product page consolidates the exact orderable MPN, interface characteristics, package information, design guidance, and sourcing questions into one engineering reference. It also distinguishes documented drop-in substitutions from merely similar RS-232 devices, helping engineers avoid PCB, logic-family, or voltage-swing mismatches during redesign and maintenance.

RFQ پەیوەندی
ADM237LAR - 5V 120kbps RS-232 Transceiver | Analog Devices
ADM237LAR

ADM237LAR - 5V 120kbps RS-232 Transceiver | Analog Devices

Analog Devices ADM237LAR is a 5 V powered CMOS RS-232 interface IC integrating five drivers, three receivers, and onboard DC-DC converters in a 24-pin SOIC package. It supports a 4.75 V to 5.25 V supply, operates at up to 120 kB/s, and provides approximately ±9 V output swing. The device is designed for compact point-to-point serial interfaces where transmitter bias voltages must be generated from a single low-voltage supply. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 levels back into digital logic. The RS-232 interface belongs to the broader interface-IC and data-communication semiconductor categories. It is intended for point-to-point serial links between computers, industrial controllers, test equipment, and peripheral systems where single-ended logic cannot directly meet the EIA-232-E and V.28 voltage requirements. The ADM237LAR combines five transmit channels and three receive channels, allowing several communications ports to share one package. Its 120 kB/s maximum data rate supports moderate-speed control and instrumentation links. Operation from a single 4.75 V to 5.25 V supply simplifies system power design because the integrated converters generate the bipolar voltage levels needed by RS-232 drivers without requiring a separate negative supply rail. The onboard DC-DC architecture is a key technical feature because it separates the device's 5 V supply requirement from the higher-amplitude RS-232 signal levels. This allows the IC to operate from common 5 V logic systems while maintaining approximately ±9 V driver swing. The CMOS implementation combines this voltage-generation capability with a 24-lead surface-mount package suitable for compact equipment. Typical applications include industrial serial controllers, laboratory data-logging equipment, point-of-sale systems, security equipment, and embedded service interfaces. The five-driver, three-receiver arrangement is particularly useful when a system needs multiple unidirectional outputs and several inputs on the same RS-232 port. Its 120 kB/s limit should be treated as the design ceiling when choosing cable length, baud rate, and protocol timing. The main design consideration is that ADM237LAR is listed as obsolete. Existing equipment can be maintained with this device when exact functional continuity is required, but new designs should evaluate a current interface product and confirm pin compatibility, supply requirements, and driver direction assignments before making any substitution. Use the manufacturer pin-description table when assigning PCB tracks and connecting external charge-pump capacitors. This page combines the device's key RS-232 characteristics, lifecycle status, sourcing information, and engineering guidance with comparison-oriented selection criteria. It helps designers distinguish the ADM237LAR from lower-speed, higher-voltage, or differently pinned interface circuits while emphasizing the need for schematic-level verification before replacement.

RFQ پەیوەندی