بەرهەمەکان (5,100+)

ADM237LJN - 120kbps 5V RS-232 Interface IC | Analog Devices
ADM237LJN

ADM237LJN - 120kbps 5V RS-232 Interface IC | Analog Devices

The Analog Devices ADM237LJN is a 5 V powered CMOS RS-232 interface IC with five drivers, three receivers, a 120 kbps data rate, and onboard DC-to-DC converters that produce approximately ±9 V output swing. The device is supplied in a 24-pin PDIP package. According to the manufacturer datasheet, it meets EIA-232-E and V.28 specifications, supports low-power shutdown at 1 µA or less, and accepts receiver input voltages of ±30 V. An RS-232 interface IC is a transceiver that connects low-voltage digital logic to a bipolar serial communications port. It combines line drivers, which convert CMOS logic into RS-232 voltage levels, with line receivers, which convert RS-232 signals back into CMOS-compatible logic. As an interface IC within the broader semiconductor category, the ADM237LJN allows equipment to communicate with RS-232 devices when a conventional ±12 V supply and external level-shifting circuitry are unavailable. The ADM237LJN operates from a single 5 V supply while generating the bipolar voltage levels required for RS-232 transmission. Its onboard DC-to-DC converters produce approximately ±9 V output swing, while the use of small 1 µF capacitors helps reduce the external support-component burden. The 120 kbps maximum data rate supports legacy serial links commonly found in industrial-control, instrumentation, test-equipment, and point-of-sale systems. The five-driver and three-receiver arrangement supports multiple RS-232 channels without requiring a separate interface IC for every line. Shutdown control can reduce supply consumption to 1 µA or less when the interface is not active. Receiver inputs tolerate ±30 V, improving robustness against voltage transients encountered on long or noisy cable connections. These characteristics make the device useful where a single logic supply must also support a physical-layer port protected from moderate overstress. Typical applications include industrial serial controllers, laboratory instruments, barcode and point-of-sale equipment, data-acquisition systems, and service interfaces on embedded products. In these systems, the ADM237LJN can bridge UART or general-purpose I/O signals to an RS-232 connector. Designers should still provide appropriate cable protection, grounding, and connector-level surge mitigation for installations where cables extend beyond controlled equipment wiring. A key design consideration is that the ADM237LJN is intended for RS-232 rather than RS-485 or RS-422 signaling. Its onboard charge-pump converters and driver outputs create bipolar RS-232 levels, so the transceiver cannot be connected directly to a differential RS-485 bus. Review the datasheet pin and capacitor recommendations before layout because converter and charge-pump performance depends on correct capacitor placement and low-impedance supply routing. This page combines the manufacturer electrical capabilities, package details, interface applications, design guidance, and validated cross-reference findings. It also distinguishes genuine same-footprint drop-in options from superficially similar RS-232 transceivers whose pin counts or electrical functions do not permit PCB-level substitution.

RFQ پەیوەندی
ADM237LJR - 5V 5-Driver 3-Receiver RS-232 | Analog Devices
ADM237LJR

ADM237LJR - 5V 5-Driver 3-Receiver RS-232 | Analog Devices

Analog Devices ADM237LJR is a 5 V powered CMOS RS-232 driver/receiver transceiver with five drivers, three receivers, and a 24-SOIC package. It operates from a single 5 V power supply, supports data rates up to 120 kB/s, and provides 9 V output swing using onboard DC-DC converters. The device is designed for systems that require RS-232 communication without externally supplied positive and negative voltage rails. An RS-232 interface transceiver belongs to the communications IC hierarchy and combines digital line-driver and receiver functions with the voltage conversion needed for unbalanced point-to-point serial links. The ADM237LJR is a multichannel variant intended to reduce the number of interface packages required in industrial control, instrumentation, data acquisition, and embedded systems. Its five-driver and three-receiver organization supports asymmetric channel counts where several devices transmit and fewer devices receive data. Key features include single 5 V operation, compliance with EIA-232-E and V.28 specifications, a maximum data rate of 120 kB/s, onboard DC-DC converters, and a 9 V output swing from a 5 V supply. The advertised 1 µF charge-pump capacitor requirement helps keep the external component count low. Low-power shutdown is supported, while the receivers remain active during shutdown according to the supplied manufacturer and distributor information. The integrated charge-pump architecture raises the 5 V supply to the bipolar voltage levels required by RS-232 drivers. This architecture eliminates a separate external power supply for positive and negative transceiver rails, although the internal converters, driver output swing, receiver thresholds, and supply noise still require careful PCB treatment. With three receivers receiving up to 30 V input, the receive network must be protected from excessive voltage and ESD exposure. Typical uses include multi-channel RS-232 test equipment, industrial data-acquisition controllers, serial port expanders, point-of-sale terminals, communications adapters, and embedded control systems. A design with more than three receive endpoints should account for the receiver-count limitation, while a design requiring more than five transmit endpoints needs another transceiver or a different channel configuration. Place the charge-pump capacitors and interface bypass capacitors close to their specified pins, and route each RS-232 driver and receiver as a separate routed signal rather than through shared buses. Confirm connector-level transient protection and chassis grounding separately from logic-side protection because the ADM237LJR is not a surge-protection device. This product page consolidates the verified manufacturer description, distributor pricing, channel configuration, package information, interface characteristics, and practical replacement guidance. It also distinguishes a true same-package alternative from related devices that differ in package, channel count, or interface function, preventing a functionally similar part from being presented as an unqualified drop-in replacement.

RFQ پەیوەندی
ADM238LAN - 120 kbps 4/4 RS-232 Transceiver | Analog Devices
ADM238LAN

ADM238LAN - 120 kbps 4/4 RS-232 Transceiver | Analog Devices

The Analog Devices ADM238LAN is a 4/4 full-duplex RS-232 transceiver with four drivers and four receivers, a 120 kB/s data rate, and a single 5 V supply in a 24-pin PDIP package. Its integrated DC-DC converters generate the bipolar voltage required by RS-232 drivers from one 5 V input, while four external 1 uF capacitors support the charge-pump circuitry. According to the manufacturer product information, the device provides a 9 V output swing with a 5 V supply, low-power shutdown, receiver operation in shutdown, and receiver input levels extending to 30 V. An RS-232 transceiver is an interface IC that combines line drivers and receivers for serial data links using the EIA-232-E and V.28 standards. It belongs to the broader interface IC hierarchy and converts between low-voltage digital logic levels and the bipolar voltage swings used on an RS-232 cable. The ADM238LAN is especially useful when a system has only a 5 V supply but requires full-duplex RS-232 connectivity rather than single-direction or unbalanced logic-level signaling. The four drivers provide transmit-side level shifting, while the four receivers support independent receive channels. A 120 kB/s maximum data rate suits industrial equipment, data acquisition systems, service interfaces, embedded controllers, and legacy peripheral connections. The single-supply architecture reduces external power complexity compared with traditional RS-232 designs that require positive and negative supplies, while the onboard converters preserve the bipolar signaling required at the cable interface. The ADM238LAN family meets EIA-232-E and V.28 requirements and supports a data rate up to 120 kB/s. Its advertised 9 V output swing is adequate for reliable RS-232 signaling in noise-prone industrial environments, and the 30 V receiver input rating provides additional protection against excessive interface voltage. The integrated shutdown function can reduce consumption when the interface is not needed, although applications must account for the device-specific shutdown and receiver-enable timing shown in the manufacturer datasheet. Typical applications include multi-port RS-232 connections in industrial controllers, laboratory instrumentation, point-of-sale equipment, telecommunications equipment, and embedded systems requiring four transmit and four receive channels. Because the device is a 4/4 transceiver, it supports full-duplex links and can handle bidirectional traffic without separate driver and receiver packages. The 24-pin PDIP package also facilitates prototyping and through-hole service access where fine-pitch surface-mount assembly is undesirable. The principal design consideration is the external charge-pump capacitor network. Use the required 1 uF capacitors with close PCB placement, observe the stated polarity, and route the high-voltage driver outputs away from sensitive logic and clock lines. Confirm the transceiver’s shutdown behavior in the system power sequence, especially when receivers must remain active while drivers are disabled. This page combines the manufacturer’s ADM238L product information with interface-family specifications and practical selection guidance. It distinguishes pin-compatible family options from related devices with different driver or receiver counts and highlights the ADM238LAN’s 120 kB/s, four-channel, single-supply architecture for engineers designing robust RS-232 links.

RFQ پەیوەندی
ADM238LANZ - 4/4 RS-232 Transceiver, 5V | Analog Devices
ADM238LANZ

ADM238LANZ - 4/4 RS-232 Transceiver, 5V | Analog Devices

The Analog Devices ADM238LANZ is a four-driver, four-receiver RS-232 transceiver designed for a single 5 V supply and data rates up to 120 kbps. It meets the EIA-232-E and V.28 interface specifications, provides approximately ±9 V driver output swing from a 5 V supply, and operates in a 24-pin plastic DIP package. Its integrated dc-to-dc converters eliminate the need for an external ±12 V supply, making the device suitable for compact serial-interface equipment. An RS-232 transceiver is an interface IC that combines differential-to-single-ended line drivers and single-ended-to-differential receivers. It belongs to the broader hierarchy of interface ICs, communication transceivers, and semiconductors. Unlike RS-422 and RS-485 interfaces, which commonly use balanced differential signaling and multipoint arrangements, RS-232 is a single-ended, point-to-point interface designed for shorter cable connections and logic-level serialization between data-terminal equipment and data-communication equipment. Key features include a single 5 V power supply, four integrated drivers, four integrated receivers, 120 kbps data-rate capability, small 1 μF charge-pump capacitors, and a shutdown mode that reduces supply current to 1 μA or less. The receiver inputs tolerate ±30 V, providing protection against voltage excursions encountered on an RS-232 connection. These characteristics make the ADM238LANZ useful where legacy RS-232 ports must coexist with modern low-voltage digital logic. The on-board dc-to-dc converters generate the bipolar voltage required by RS-232 drivers from the single 5 V rail. A 1 μF capacitor is specified for each converter, while the driver side supplies approximately ±9 V output swing. The device includes four drivers and four receivers, allowing multiple serial channels to be implemented without repeating the power-conversion circuitry. Its receiver architecture supports operation with the supply rail removed when inputs remain within the specified ±30 V range. Typical applications include industrial serial adapters, test and measurement equipment, data acquisition systems, legacy peripheral interfaces, point-of-sale equipment, and embedded-control systems that retain an RS-232 port. The integrated power conversion is especially useful where a ±12 V rail is unavailable but the logic system operates from 5 V. For each channel, the board must also provide the connector protection and signal-routing considerations appropriate to the cable environment. Design attention should be given to charge-pump capacitor placement, grounding, and protection at the connector. Keep the 1 μF converter capacitors close to their specified pins, route RS-232 traces away from sensitive analog or high-speed digital paths, and use an appropriately rated protection network for exposed cables. The shutdown function must be controlled correctly because entering shutdown disconnects the interface and reduces supply current to 1 μA or less. This page combines the ADM238LANZ operating characteristics, package information, sourcing guidance, interface design considerations, and a qualified drop-in comparison. It also identifies where a candidate replacement has the same 24-pin DIP footprint and where additional design verification is required before substitution.

RFQ پەیوەندی
ADM238LAQ - 4/4 RS-232 Transceiver, 120 kB/s | Analog Devices
ADM238LAQ

ADM238LAQ - 4/4 RS-232 Transceiver, 120 kB/s | Analog Devices

The Analog Devices ADM238LAQ is a four-driver, four-receiver RS-232 transceiver designed for single 5 V operation in a 24-lead ceramic DIP package. It supports data rates up to 120 kB/s, provides on-board DC-DC converters, and uses 1 uF capacitors for charge-pump operation. The device meets EIA-232-E and V.28 specifications while delivering a 9 V output swing from a 5 V supply. These characteristics make the ADM238LAQ suitable for industrial control, instrumentation, data acquisition, and legacy serial-port interfaces that require four RS-232 channels without external transmit voltage conversion. An RS-232 transceiver is an interface integrated circuit that combines line drivers and line receivers for bidirectional or unidirectional serial communication. It belongs to the interface IC hierarchy, converting between low-voltage CMOS logic levels and the positive and negative voltage levels used by RS-232 links. The ADM238LAQ provides four driver channels and four receiver channels, allowing one package to support several data paths or to provide transmit-only and receive-only groups on the same board. Key features include a single 5 V power supply, operation to 120 kB/s, integrated DC-DC converters, a 9 V output swing, and low-power shutdown with receivers remaining active. The receiver input withstands voltages up to 30 V according to the product information. A 1 uF charge-pump capacitor requirement and integrated conversion circuitry reduce the external component count compared with discrete RS-232 implementations. The 24-CDIP package is 0.300 inches wide, or 7.62 mm. Technically, the device integrates four CMOS RS-232 drivers, four receivers, and the supporting charge-pump converters needed to generate bipolar output levels from one 5 V rail. This architecture suits equipment with multiple asynchronous serial ports, including test systems, industrial controllers, service interfaces, and data-logging equipment. Shutdown behavior is especially useful for systems where transmitters must stop driving while incoming data must still be monitored. Typical applications include four-channel RS-232 instrument control, factory automation equipment with multiple serial links, legacy peripheral connections, and embedded control systems that retain an RS-232 interface. The 120 kB/s rate is substantially faster than the original 20 kB/s RS-232 target, although actual application throughput remains constrained by protocol overhead and cable characteristics. A key design consideration is the ceramic DIP footprint: unlike a surface-mount alternative, it requires through-hole insertion and adequate spacing for assembly and service. Designers should preserve the pinout assigned to the 24-CDIP variant, validate signal levels at the connector, and confirm that the selected charge-pump capacitors meet the manufacturer's stability and temperature requirements. This page consolidates the confirmed electrical characteristics, package information, interface use cases, and design considerations for engineers evaluating the ADM238LAQ as a four-channel RS-232 interface solution.

RFQ پەیوەندی
ADM238LAR - 4-Channel 5V RS-232 Transceiver | Analog Devices
ADM238LAR

ADM238LAR - 4-Channel 5V RS-232 Transceiver | Analog Devices

The Analog Devices ADM238LAR is a four-channel, four-transmitter and four-receiver RS-232 interface transceiver operating from a single 5 V supply. It supports data rates up to 120 kbps, generates approximately ±9 V output swings through on-board DC-DC converters, and is packaged in a 24-pin SOIC. The integrated charge-pump design eliminates the need for an external ±12 V supply, making the device suitable for compact single-board serial interfaces. An RS-232 transceiver belongs to the interface IC hierarchy, where it converts logic-level signals between a host or controller and a cable-based communications port. Unlike a direct TTL serial connection, an RS-232 interface uses unbalanced differential voltage signaling, greater noise tolerance, and inverting line levels. The ADM238LAR integrates four drivers and four receivers so one package can support multiple serial channels while preserving a compact board footprint. Key operating characteristics include compliance with EIA-232-E and V.28 interface requirements, a maximum data rate of 120 kbps, and receiver input protection extending to ±30 V. Its on-board converters permit approximately ±9 V output swing from a 5 V supply, while small 1 µF charge-pump capacitors simplify the external power-supply network. A shutdown function reduces supply current to no more than 1 µA and allows the receivers to remain active during shutdown. The ADM238LAR combines CMOS-compatible logic interfacing with integrated isolated-looking charge-pump conversion, although the interface ground remains part of the circuit and should not be interpreted as galvanic isolation. The ±30 V receiver tolerance improves robustness when a connected RS-232 port can experience ±12 V, ±15 V, or other elevated voltage levels. Latch-up-free operation further supports dependable behavior in electrically noisy equipment. Typical applications include industrial control consoles, test and measurement equipment, POS terminals, instrumentation links, and embedded systems that require several RS-232 ports without a separate negative supply rail. In multiport designs, each transmitter and receiver can be assigned to a different cable or peripheral, while the common 5 V supply simplifies system power architecture. Care is still required to control cable transients and maintain an appropriate common-mode relationship between connected equipment. For PCB implementation, place the charge-pump capacitors close to their associated pins and route each RS-232 line away from clocks, data buses, and switching-power nodes. Add suitable input protection for long or exposed cables, and verify the logic polarity of each receiver output against the firmware protocol. These practices preserve the device's low-voltage operation while improving field reliability. This product page organizes the ADM238LAR's core electrical characteristics, drop-in alternatives, application guidance, pin-package considerations, and design checks into one engineering reference. It supports component selection, schematic review, and PCB planning for single-supply RS-232 interfaces operating at up to 120 kbps.

RFQ پەیوەندی
ADM238LJN - 4/4 120kbps RS-232 IC | Analog Devices
ADM238LJN

ADM238LJN - 4/4 120kbps RS-232 IC | Analog Devices

Analog Devices ADM238LJN is a 4/4 full-duplex RS-232 line-driver and receiver interface IC with a 120 kB/s data rate, single 5 V power supply, and 24-pin PDIP package. It provides four transmit drivers and four receive channels, producing approximately 9 V output swing from the 5 V supply through on-board DC-DC converters. The device targets EIA-232-E and V.28 serial interfaces where a ±12 V supply is unavailable. An RS-232 transceiver is an interface IC that combines differential digital signaling levels with a single logic-level supply. In the broader electronics hierarchy, the ADM238LJN belongs to the interface IC class, specifically the RS-232 transceiver family. Its integrated DC-DC converter generates the higher voltage needed for RS-232 driver outputs while the receiver circuitry restores serial data to compatible logic levels. The ADM238LJN's principal features include a 120 kB/s data rate, 9 V output swing, 1 F charge-pump capacitors, a low-power shutdown function, and receivers that remain active during shutdown. A 1 A receiver output capability supports the stated receiver-load condition, while the 30 V receiver-input rating provides additional tolerance for exposed serial lines. These characteristics simplify legacy and industrial RS-232 connections without requiring a separate negative supply rail. The device is intended for EIA-232-E and V.28 communications interfaces, including industrial equipment, instrumentation, data-acquisition systems, service consoles, and legacy peripheral connections. Four full-duplex channels allow one connector to carry four data paths in each direction. Its 120 kB/s rate is suitable for conventional serial control and communication links rather than high-speed differential or Ethernet protocols. PCB design must preserve the RS-232 interface requirement for a single 5 V supply even though driver outputs swing to approximately 9 V. Place the specified 1 F capacitors close to the charge-pump pins, route driver outputs away from sensitive receiver and logic traces, and maintain the 24-pin PDIP footprint without changing the land pattern. Review the receiver input rating before connecting externally accessible lines. The ADM238LJN is listed as obsolete, so availability may be limited. This page synthesizes the device specifications, sourcing guidance, drop-in comparison, application guidance, and design considerations that engineers need when supporting an installed ADM238LJN design.

RFQ پەیوەندی
ADM238LJNZ - 4/4 RS-232 Transceiver, 5V, 100k BPS | Analog Devices
ADM238LJNZ

ADM238LJNZ - 4/4 RS-232 Transceiver, 5V, 100k BPS | Analog Devices

The Analog Devices ADM238LJNZ is a low-power, +5V CMOS RS-232 transceiver with 4 drivers and 4 receivers, operating at up to 100 k BPS and housed in a 24-pin PDIP package. The device is intended for EIA-232-E and V.28 communications interfaces where a conventional ±12 V supply is unavailable. Its four-driver, four-receiver arrangement consolidates two full RS-232 channels into one package, making it useful for multi-port serial connectivity, industrial equipment, instrumentation, and embedded control systems. An RS-232 transceiver is an interface integrated circuit that combines line drivers and line receivers. The driver converts TTL-compatible logic signals into RS-232-compatible levels, while the receiver converts incoming RS-232 signals back into logic levels. In the broader hierarchy, the ADM238LJNZ belongs to the interface IC family, specifically the RS-232 transceiver and communications-interface category. The 24-pin PDIP format supports through-hole assembly and straightforward panel or legacy industrial PCB layouts. The ADM238L family is designed for low-power operation from a single +5V supply. The manufacturer identifies the device as a 5V CMOS RS-232 driver/receiver set with four drivers and four receivers. Its 100 k BPS communication rate is suitable for moderate-speed data links rather than high-speed synchronous or differential bus applications. The four-channel organization reduces the number of interface packages required when several RS-232 ports must share a common supply and ground architecture. Typical uses include industrial controllers, barcode and weighing equipment, test systems, security equipment, and board-level communication links. Because the device operates from +5V, it can be placed between a modern microcontroller UART and an external RS-232 connector without requiring a separate bipolar supply. The logic-side interface remains compatible with the voltage levels used by the surrounding digital circuitry, while the line-side interface provides the voltage translation required by RS-232. PCB implementation should preserve the manufacturer’s recommended decoupling arrangement and provide adequate copper and signal-return paths for the RS-232 connector. RS-232 is an unbalanced, point-to-point interface, so cable length, grounding, protection, and connector transients can influence reliability. Shielded or transient-protected cabling is appropriate when the port is exposed to industrial electrical noise. The manufacturer product page and ADM238L datasheet remain the primary references for pin assignment, electrical limits, and application-circuit details. This page organizes the ADM238LJNZ specifications, package information, pricing references, pin-level application guidance, and available drop-in cross-reference information into an engineering-focused resource. It also identifies the principal design trade-offs between the ADM238LJNZ and other RS-232 transceiver options, helping designers select the interface device that best fits their voltage, throughput, packaging, and assembly requirements.

RFQ پەیوەندی
ADM238LJR - 4/4 5V RS-232 Transceiver | Analog Devices
ADM238LJR

ADM238LJR - 4/4 5V RS-232 Transceiver | Analog Devices

The Analog Devices ADM238LJR is a four-driver, four-receiver RS-232 transceiver powered by a single 5 V supply and packaged in a 24-pin SOIC. It supports data rates up to 120 kB/s, provides approximately 9 V driver output swing from the 5 V supply, and operates with 1 uF capacitors according to the manufacturer feature summary. The device is designed for EIA-232-E and V.28 interfaces where traditional positive and negative ±12 V supplies are unavailable. An RS-232 transceiver is an interface IC that combines differential signaling drivers and receivers for point-to-point serial communication. The ADM238LJR belongs to the RS-232 interface transceiver category, where the transmitter converts logic-level signals into RS-232-compatible levels and the receiver converts those levels back into CMOS-compatible signals. Its four independent channels support bidirectional data paths in equipment requiring more than one serial connection. The integrated DC-DC converter allows the IC to generate the positive and negative voltages needed by RS-232 drivers from one 5 V supply. This reduces external power-supply complexity while preserving the required bipolar signaling levels. The manufacturer lists approximately 9 V output swing, low-power shutdown, receivers that remain active during shutdown, and 1 uF external capacitors as key operating characteristics. The ADM2xx family supports EIA-232-E and V.28 communications interfaces, and the driver architecture is designed for data transmission beyond the formal EIA-232-E rate. The ADM238LJR combines four transmit channels and four receive channels in one device, making it suitable for console links, instrumentation, industrial control equipment, and legacy peripheral connectivity. A single IC can serve multiple RS-232 ports while centralizing supply and decoupling requirements. Common application areas include industrial controllers, test and measurement equipment, point-of-sale terminals, security systems, and embedded systems that retain an RS-232 interface. The 24-pin SOIC package is suitable for conventional surface-mount PCB assembly. Designers should maintain the required charge-pump capacitor connections and place bypass and charge-pump capacitors close to their associated pins according to the manufacturer datasheet layout guidance. The principal design trade-off is that its four-driver, four-receiver arrangement is more specialized than single-channel transceivers. It provides higher channel density and simpler 5 V-only power design, but applications needing only one RS-232 link may not use every channel. Input protection, cable length, grounding, and data-rate limits must be evaluated against the EIA-232-E and V.28 interface requirements. This page organizes the ADM238LJR specifications, pin-compatible family alternatives, application guidance, and comparison criteria to support component selection and PCB planning. It also identifies the documentation and electrical details that require confirmation in the Analog Devices data sheet before production release.

RFQ پەیوەندی
ADM239LAN - 5V 3/5 RS-232 Transceiver | Analog Devices
ADM239LAN

ADM239LAN - 5V 3/5 RS-232 Transceiver | Analog Devices

The Analog Devices ADM239LAN is a 5 V powered CMOS RS-232 transceiver combining three drivers and five receivers in a 24-pin PDIP package. It supports data rates up to 120 kB/s, meets the EIA-232-E and V.28 specifications cited in the manufacturer documentation, and provides an on-board DC-DC converter that produces a 9 V output swing from the single 5 V supply. These characteristics make the ADM239LAN useful for industrial equipment, data acquisition systems, and service interfaces where a compact multichannel RS-232 solution is required. An RS-232 transceiver is an interface IC that translates between complementary logic-level signals and the voltage levels defined by the EIA-232 standard. A transmitter converts logic data into RS-232 line signals, while a receiver converts incoming line signals back into CMOS-compatible data. In the broader semiconductor hierarchy, the ADM239LAN is a line driver and receiver, then an interface transceiver, and ultimately an interface IC. Its three transmitters permit three outgoing data channels, while its five receivers provide five incoming channels. The principal features of the ADM239LAN are its single 5 V supply operation, 120 kB/s data rate, integrated DC-DC conversion, approximately 9 V output swing, low-power shutdown capability, and receiver operation during shutdown. The integrated DC-DC converter eliminates the need for a separate external RS-232 charge-pump supply in applications where the 5 V system rail is already available. The shutdown function can reduce consumption when the interface is not actively communicating. The verified manufacturer-related search information identifies the ADM239LAN as a 5 V powered CMOS RS-232 driver and receiver device and confirms the 3/5 channel arrangement through the available comparison result. The listed package is 24-pin PDIP, which provides a through-hole footprint with widely spaced leads for easier inspection and assembly. Detailed pin names, receiver input thresholds, supply-current limits, and operating-temperature limits were not included in the supplied verification data and therefore are not inferred here. Typical uses include multiport industrial controller connections, laboratory instrument control, point-of-sale equipment, and embedded systems that need several RS-232 channels sharing one logic-level supply. The integrated DC-DC approach is particularly useful where board space is constrained. System designers should still account for the higher line-side voltage, maintain appropriate RS-232 grounding, and verify transient protection for cables connected to external equipment. This page combines the verified ADM239LAN specifications, package information, purchasing-source links, interface application guidance, and a conservative drop-in replacement assessment. It distinguishes electrically similar family members from alternatives that require a different package or an engineering review, helping engineers avoid assuming that a similar RS-232 device is pin-compatible.

RFQ پەیوەندی
ADM239LAQ - 120 kbps RS-232 Interface | Analog Devices
ADM239LAQ

ADM239LAQ - 120 kbps RS-232 Interface | Analog Devices

The Analog Devices ADM239LAQ is a +5 V powered CMOS RS-232 driver and receiver interface IC with a 120 kbps data rate, on-board DC-DC converters, and a 24-lead CDIP package. It supports three drivers and three receivers, provides approximately 9 V output swing from a 5 V supply, and accepts receiver inputs up to 30 V. An RS-232 interface IC is a semiconductor that converts logic-level signals between a host or peripheral and the voltage levels used by the EIA-232-E serial bus. The ADM239LAQ combines CMOS transceivers, charge-pump converters, driver slew control, receiver threshold detection, and shutdown control in one integrated device. It sits between digital logic and the physical RS-232 connector. Key features include operation from a single +5 V supply, support for 120 kbps data rates, TTL- and CMOS-compatible receiver thresholds, and low-power shutdown. The on-board DC-DC converters generate the elevated voltage required for RS-232 driver outputs. A 9 V output swing from the 5 V supply supports reliable communication over longer cable runs than a conventional ±5 V-compatible interface. The receiver switching threshold is VCC/4, which is 1.25 V typical at a 5 V supply. Unused receiver inputs may remain unconnected because an internal 400 kΩ pull-up forces the corresponding output low. The EIA-232-E implementation also limits driver slew rate, helping control unwanted ringing and electromagnetic interference on connected cables. Typical applications include industrial serial controllers, test and measurement equipment, point-of-sale terminals, diagnostic interfaces, and embedded systems that need bidirectional RS-232 communication without an external negative supply. The device is particularly useful when equipment must combine several RS-232 ports with low-power standby operation on a single 5 V rail. Designers should follow the manufacturer datasheet for external charge-pump capacitor selection, receiver and driver pin assignments, and unused-channel handling. Place the required capacitors close to their associated pins and route the RS-232 connector interface away from sensitive analog or high-speed digital circuits to minimize coupling. This page combines the ADM239LAQ electrical characteristics, interface guidance, application fit, and verified sourcing information in one engineering-focused reference. It helps designers distinguish the device's integrated DC-DC architecture, 120 kbps capability, shutdown behavior, and 30 V receiver tolerance when planning an RS-232 interface.

RFQ پەیوەندی
ADM239LAR - 5V RS-232 Interface with DC-DC | Analog Devices
ADM239LAR

ADM239LAR - 5V RS-232 Interface with DC-DC | Analog Devices

Analog Devices ADM239LAR is a 5 V powered CMOS RS-232 drivers and receivers IC with 3 driver channels, 5 receiver channels, 120 kB/s data rate, and an on-board DC-DC converter. It is packaged in a 24-lead SOIC measuring 0.295 inch, or 7.50 mm, wide. The device also provides low-power shutdown, 1 μF charge-pump capacitors, 9 V output swing from a 5 V supply, and receiver inputs rated to 30 V. An RS-232 transceiver is an interface IC that converts logic-level digital signals into differential, bipolar RS-232 signals and converts received RS-232 signals back into CMOS logic levels. The RS-232 transceiver belongs to the serial-interface hierarchy, which includes interface ICs, line drivers and receivers, communication transceivers, and broader data-communication semiconductors. It is designed for equipment-to-equipment communication over cables where voltage levels exceed ordinary CMOS input and output ranges. The ADM239LAR's principal advantages include operation from one 5 V supply, compliance with EIA-232-E and V.28 specifications, a maximum data rate of 120 kB/s, and an integrated DC-DC converter that generates the elevated RS-232 output voltage. Its 9 V output swing provides useful noise margin over the approximately 2 V RS-232 transition region. Low-power shutdown reduces consumption when the interface is not required, while the receiver remains active during shutdown. The integrated charge-pump circuit develops the bipolar transmitter voltage required by RS-232 from the single 5 V supply. The manufacturer datasheet specifies small 1 μF capacitors for the charge-pump circuit. Three transmitters provide enough channels for common control, status, and data paths, while five receivers allow the opposite direction of the link to carry several signals. The CMOS implementation supports integration into systems that already operate from 5 V rather than requiring the additional negative supply traditionally associated with RS-232. Typical uses include industrial control links, point-of-sale equipment, test and measurement instruments, data-acquisition systems, and embedded equipment interfaces. In each case, the ADM239LAR can translate between a 5 V controller and an external RS-232 port. The 120 kB/s rate is suitable for moderate-speed serial links, while the integrated DC-DC converter simplifies implementation where only a positive 5 V rail is available. The main design consideration is external line protection. Although the receiver input is specified to 30 V, exposed RS-232 ports may encounter larger transients or incorrect polarity. Appropriate surge and ESD protection should be added where the cable environment requires it, and unused driver outputs should be handled according to the manufacturer recommendations. This page consolidates the verified ADM239LAR specifications, sourcing information, procurement details, interface-application guidance, and data gaps that are not resolved by the supplied manufacturer and distributor records.

RFQ پەیوەندی
ADM239LJR - 120 kB/s 5V RS-232 Interface | Analog Devices
ADM239LJR

ADM239LJR - 120 kB/s 5V RS-232 Interface | Analog Devices

The Analog Devices ADM239LJR is a 5 V powered CMOS RS-232 driver and receiver interface IC with three transmitters, five receivers, a 120 kB/s data rate, on-board DC-DC converters, and a 24-pin SOIC wide package. It supports low-power shutdown while maintaining active receivers, produces a 9 V output swing from a 5 V supply, accepts receiver inputs up to 30 V, and uses small 1 µF capacitors. An RS-232 interface transceiver is a physical-layer integrated circuit that converts logic-level signals into RS-232-compatible voltage levels and converts received RS-232 signals back into CMOS-compatible levels. The ADM239LJR belongs to the line-driver and line-receiver hierarchy, which falls within interface ICs and broader digital and analog semiconductors. Its integrated charge-pump DC-DC converters provide the voltage needed for bipolar RS-232 output drive without requiring a separate 12 V supply. Key features include a single 5 V power supply, compliance with the EIA-232-E and V.28 specifications cited in the retrieved datasheet listing, a 120 kB/s data rate, and three drivers with five receivers. The on-board converters produce a 9 V output swing with a 5 V supply. Low-power shutdown reduces consumption when the interface is not needed, while 1 A receivers remain active during shutdown. The receiver input withstands voltages up to 30 V. The device combines a multichannel RS-232 line interface with internal power-conversion circuitry, reducing the number of external supply rails required by the board. Its CMOS implementation and specified 9 V swing target systems that must bridge short-distance, point-to-point serial links through single-ended RS-232. The combination of three drivers, five receivers, and shutdown behavior supports compact communications equipment where multiple serial lines and power conservation are important. Typical uses include industrial serial-port adapters, data-acquisition equipment, point-of-sale terminals, embedded control consoles, and instrumentation requiring RS-232 connectivity from a 5 V system. A transmitter converts outgoing UART or peripheral logic into RS-232 levels, while the five receivers allow multiple incoming lines to be monitored. The 120 kB/s rate is suitable for many legacy serial-control and data-transfer tasks when paired with a compatible UART and protocol. Designers should verify the external charge-pump capacitor values, UART signal levels, connector protection, and shutdown-state behavior against the Analog Devices datasheet before layout release. Keep RS-232 traces away from sensitive analog and high-speed digital paths, provide the specified bypass capacitance at the supply pins, and account for the 30 V receiver input limit when exposed to industrial wiring or ESD events. This page consolidates the verified ADM239LJR features, current distributor pricing references, package information, application guidance, and a transparent assessment of available drop-in alternatives. It also distinguishes documented device capabilities from fields not supplied by the retrieved sources, preventing unverified electrical claims from being presented as manufacturer specifications.

RFQ پەیوەندی
ADM241LAR - 120 kbps 4/5 RS-232 Transceiver | Analog Devices
ADM241LAR

ADM241LAR - 120 kbps 4/5 RS-232 Transceiver | Analog Devices

The Analog Devices ADM241LAR is a 5 V powered CMOS RS-232 interface transceiver with four drivers, five receivers, and a maximum data rate of 120 kbps. It uses a single 5 V supply, provides approximately ±9 V driver output swing through on-board DC-DC converters, and is packaged in a 28-pin SOIC for surface-mount industrial equipment. An RS-232 transceiver is an interface IC that combines line drivers and line receivers for serial data links using the EIA-232-E and V.28 specifications. The driver channels convert low-voltage logic signals into bipolar RS-232 levels, while the receiver channels convert bipolar line signals back into logic levels. This integrated transceiver category reduces the number of external components required where both transmission and reception are needed in the same equipment. Key features include a single 5 V power supply, four drivers, five receivers, 120 kbps operation, and on-board DC-DC converters that generate approximately ±9 V output swing. The interface uses small 1 µF charge-pump capacitors and includes a low-power shutdown mode in which supply current is no more than 1 µA. Receiver inputs withstand voltages up to ±30 V, improving tolerance to exposed serial-port wiring and transients. The integrated charge-pump architecture eliminates the need for an external ±12 V supply, making the ADM241LAR appropriate for equipment that otherwise operates entirely from 5 V. Its five receivers provide one more receive channel than its four driver channels, which supports designs with an additional receive-only signal, an echo-detection path, or a status input. The 28-pin SOIC package also offers a larger lead pitch than fine-pitch packages, easing assembly and inspection. Typical applications include industrial serial-port adapters, data-acquisition equipment, test and measurement instruments, point-of-sale terminals, barcode scanners, and embedded control systems that exchange RS-232 data with external peripherals. The interface is especially useful when the host lacks a native RS-232 transceiver and the connected equipment requires bipolar signaling rather than a 3.3 V or 5 V logic-level serial port. Design the charge-pump capacitor network and input/output protection for the voltage and current limits stated in the Analog Devices datasheet. Keep the connector-side interface path physically separated from sensitive logic and power traces, provide the required bypass capacitance near the supply pins, and verify signal integrity at the intended baud rate before treating the 120 kbps figure as a guaranteed system-level result. This product page organizes the ADM241LAR’s interface characteristics, package information, sourcing path, design guidance, and replacement considerations into a compact engineering reference. It also distinguishes verified device identity from compatibility checks that must still be completed before approving any substitute in an existing PCB design.

RFQ پەیوەندی
ADM241LARZ - 5V 4/5 RS-232 Transceiver | Analog Devices
ADM241LARZ

ADM241LARZ - 5V 4/5 RS-232 Transceiver | Analog Devices

Analog Devices ADM241LARZ is a single-supply RS-232 transceiver with four drivers and five receivers, a maximum data rate of 120 kB/s, and integrated DC-DC converter support for ±9 V output swing. It operates from a 5 V supply in a 28-lead WSOIC package, making it suitable for compact, single-board serial-interface equipment. An RS-232 transceiver is an interface IC that combines voltage-line drivers and receivers for bidirectional or multipoint serial communication. RS-232 belongs to the interface-IC hierarchy and uses positive and negative voltage levels to represent digital logic. The ADM241L family is designed for EIA-232-E and V.28 communication interfaces where separate ±12 V supplies are impractical. A single 5 V rail and onboard charge-pump circuitry simplify system power design. The ADM241LARZ integrates four driver channels and five receiver channels, allowing one package to support several serial links or a mix of transmit and receive functions. Its 120 kB/s maximum data rate suits equipment-control, instrumentation, point-of-sale, industrial, and data-acquisition links that do not require the throughput of a high-speed LVDS interface. Onboard DC-DC converters produce approximately ±9 V output swing, while the small external capacitor requirement of 1 µF reduces board area. Operationally, the device separates low-voltage logic signaling from the bipolar RS-232 interface. The four drivers translate logic-high and logic-low inputs into RS-232 levels, while the five receivers convert bipolar line voltages back into digital logic outputs. The receiver population is one channel higher than the driver population, allowing a design with four outgoing channels and five incoming channels. The transmitter and receiver enables provide local control over bus participation. Typical uses include industrial control terminals, laboratory interfaces, POS systems, embedded service ports, and legacy peripheral connections. It is particularly useful when the equipment needs several RS-232 ports but has only a 5 V power rail. Compared with discrete RS-232 drivers and receivers, the integrated device reduces footprint, component count, and the chance of inconsistent charge-pump routing. For layout, place the 1 µF charge-pump capacitors close to their designated pins and route the high-current loops with minimal area. Keep the logic side away from connector-side return paths, observe the supply and enable sequencing requirements, and test signal integrity with the actual cable and load. The WSOIC package also requires thermal consideration when several drivers operate continuously on bus-limited signals. This product page consolidates the verified electrical facts, package information, replacement analysis, interface applications, and PCB-design guidance for the ADM241LARZ. It also distinguishes genuine pin-compatible alternatives from related interface ICs that use a different package or channel count.

RFQ پەیوەندی
ADM241LJR - 120 kbps RS-232 Transceiver | Analog Devices
ADM241LJR

ADM241LJR - 120 kbps RS-232 Transceiver | Analog Devices

The Analog Devices ADM241LJR is a four-driver, five-receiver RS-232 transceiver designed for serial communications from a single 5 V supply. It supports data rates up to 120 kbps, produces approximately ±9 V driver output swing through onboard DC-to-DC converters, and is available in a 28-pin SOIC package. The device is intended for systems that cannot provide separate ±12 V RS-232 supply rails. An RS-232 transceiver is an interface IC that combines line drivers and receivers on a serial data link. The drivers translate low-voltage logic signals into bipolar RS-232 levels, while the receivers convert those bipolar levels back into CMOS-compatible logic. Within the broader hierarchy, the ADM241LJR is a serial-interface transceiver, an interface IC, and a semiconductor designed for data communication and signal conditioning. The ADM241LJR operates from one 5 V supply and includes onboard DC-to-DC converters, eliminating the need for a separate negative supply for driver operation. It complies with EIA-232-E and V.28 interface requirements, supports operation at 120 kbps, and accepts receiver input voltages of ±30 V. Small 1 µF charge-pump capacitors reduce the external component count, while the shutdown feature limits supply current to 1 µA or less. The four drivers can independently support transmit channels, and the five receivers support receive or monitoring channels. This channel mix suits equipment that requires multiple serial outputs but has an asynchronous status, control, or acknowledgment input. The receiver circuit is designed to tolerate ±30 V input levels, improving robustness in industrial environments where connected equipment can impose voltage stress on an interface port. Typical applications include industrial control panels, test and measurement equipment, data acquisition systems, point-of-sale terminals, and service interfaces for remotely operated equipment. The 120 kbps maximum rate is suitable for legacy serial links, configuration ports, and equipment-control links that do not require the throughput and protocol complexity of a modern high-speed serial interface. Designers should place charge-pump capacitors and interface protection components close to the device, route driver outputs as short as practical, and maintain a common ground reference between communicating systems. The 5 V supply and ground planes require normal bypass-capacitor placement, while exposed RS-232 connectors should include suitable surge and electrostatic-discharge protection because the ADM241LJR is not presented as a dedicated hardened RS-485 transceiver. This page combines the ADM241LJR operating characteristics, interface use cases, design considerations, and verified source links to support component selection, schematic planning, and PCB implementation.

RFQ پەیوەندی
ADM241LJRS - 120kbps RS-232 Transceiver | Analog Devices
ADM241LJRS

ADM241LJRS - 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices ADM241LJRS is a 4/5 RS-232 transceiver operating from a single 5 V supply, supporting data rates up to 120 kbps in a 28-pin SSOP package. It integrates four drivers and five receivers, on-board DC-to-DC converters, and charge-pump circuitry that produces approximately ±9 V output swing without requiring external ±12 V power rails. The interface meets EIA-232-E and V.28 requirements. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar differential signaling used by RS-232 equipment. It belongs to the interface IC hierarchy, combining line drivers, line receivers, voltage conversion, and port protection into a complete communications interface. This integration is especially useful when the equipment only has a 5 V supply but must communicate with legacy RS-232 ports requiring positive and negative signal voltages. The ADM241LJRS supports a maximum 120 kbps data rate while consuming small 1 µF charge-pump capacitors. Its integrated converters eliminate separate negative-voltage generation circuitry, reducing board area and external component count. A low-power shutdown mode reduces supply current to 1 µA or less, and the receiver inputs tolerate voltages up to ±30 V. The 28-pin SSOP package provides enough channel capacity for four transmit and five receive functions. The ADM241LJRS is intended for industrial control, instrumentation, data acquisition, point-of-sale equipment, and embedded serial-port designs. Its four-driver and five-receiver arrangement suits equipment that sends commands and status information while receiving data from several peripherals. The single 5 V rail also simplifies compatibility with modern digital systems that no longer provide the ±12 V rails traditionally associated with RS-232. PCB design should prioritize short traces between the device and charge-pump capacitors because high-current switching paths can create radiated noise and ground disturbance. Place the interface connector, protection network, transceiver, and connector-side ground connection in a controlled signal-flow arrangement. Review the manufacturer datasheet before finalizing capacitor selection, connector protection, and logic-family compatibility. This page combines the manufacturer's published interface capabilities with application guidance, practical design considerations, verified source links, and a strict assessment of drop-in replacement options. Engineers can use the comparison and selection information to determine whether the ADM241LJRS matches the required channel count, package, data rate, and RS-232 system architecture.

RFQ پەیوەندی
ADM241LJRSZ - 4/5 RS-232 5V 120kB/s | Analog Devices
ADM241LJRSZ

ADM241LJRSZ - 4/5 RS-232 5V 120kB/s | Analog Devices

Analog Devices ADM241LJRSZ is a four-driver, five-receiver full-duplex RS-232 interface transceiver operating from a single 5 V supply at up to 120 kB/s. The device is packaged in a 28-pin SSOP and includes onboard DC-DC converters that produce approximately ±9 V output swing without requiring external ±12 V rails. It is designed for EIA-232-E and V.28 communications interfaces. A full-duplex RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible line levels and converts incoming RS-232 signals back into CMOS-compatible digital levels. The ADM2xx family belongs to the broader line-driver/receiver and interface-IC hierarchy, making it useful where equipment communicates over short point-to-point serial links without a separate negative supply. Key features include four RS-232 drivers, five RS-232 receivers, a single 5 V power supply, and a maximum data rate of 120 kB/s. Onboard DC-DC conversion supports approximately ±9 V output swing, while small 1 µF charge-pump capacitors help reduce the external component count. The architecture is intended to meet EIA-232-E and V.28 interface requirements in industrial, instrumentation, data-acquisition, and embedded-control systems. The integrated charge-pump circuitry allows the transceiver to operate from one 5 V rail rather than conventional ±12 V or ±15 V supplies. This simplifies system power architecture, but the DC-DC converter and driver outputs introduce switching-related considerations around board layout and cable routing. Input and output pins must also be checked against the 4.75 V to 5.25 V supply specification before connecting external logic. Typical uses include industrial control links, laboratory test equipment, POS terminals, medical-instrument interfaces, and embedded systems that exchange RS-232 commands or status data. The four-driver and five-receiver arrangement supports multiple transmit and receive channels in one package, which can reduce board area when several point-to-point RS-232 links terminate on the same controller. PCB layout should keep the 1 µF charge-pump capacitors close to their associated pins, provide a low-impedance 5 V supply connection, and route the RS-232 traces away from sensitive analog and clock signals. Because the transceiver includes a DC-DC converter, use the manufacturer’s recommended grounding and bypass-capacitor arrangement to minimize conducted and radiated emissions. This product page combines the ADM241L family electrical characteristics, 28-SSOP footprint information, package temperature distinctions, and application-oriented design guidance to support faster component selection and PCB implementation.

RFQ پەیوەندی
ADM241LJRZ - 120 kbps RS-232 Transceiver | Analog Devices
ADM241LJRZ

ADM241LJRZ - 120 kbps RS-232 Transceiver | Analog Devices

Analog Devices ADM241LJRZ is a four-driver, five-receiver RS-232 transceiver designed for a single 5 V supply. It supports data rates up to 120 kB/s, provides approximately ±9 V output swing, and uses small 1 µF charge-pump capacitors. The device is offered in a 28-pin SOIC package and is intended for EIA-232-E and V.28 communication interfaces where ±12 V is unavailable. An RS-232 transceiver is an interface IC that converts logic-level signals from a host or controller into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible levels. It belongs to the line-driver and receiver hierarchy within the broader interface-IC and communications-IC categories. The ADM241L family uses on-board DC-DC converters to generate the bipolar voltage needed for compliant RS-232 operation from one low-voltage supply. The ADM241LJRZ provides four transmit channels and five receive channels, allowing four RS-232 outputs and five inputs in one package. Its specified 120 kB/s data rate supports legacy serial-control, point-of-sale, industrial-control, and instrumentation links. The ±9 V output swing is particularly useful when the system does not have the ±12 V rails traditionally associated with an RS-232 interface. A shutdown function is also part of the broader ADM2xx family described by Analog Devices. Operationally, the integrated charge-pump circuitry increases the supply voltage to produce the required positive and negative line voltages. This eliminates the need for a separate dual-polarity RS-232 supply, while the small 1 µF capacitor requirement helps reduce board area. However, charge-pump ripple and switching noise remain important considerations when the transceiver shares a sensitive analog or high-speed digital supply domain. Typical uses include industrial control systems, test and measurement equipment, data-acquisition systems, security equipment, and embedded serial interfaces. The 28-pin SOIC footprint provides a practical upgrade path for designs that need four RS-232 driver outputs and five receiver inputs without using separate driver and receiver ICs. Care is still required for cable routing, ground reference, and protection at exposed connector interfaces. For PCB implementation, place the charge-pump capacitors and interface bypass capacitor close to their specified pins, keep RS-232 traces away from sensitive analog inputs, and provide the connector-side transient protection required by the installation environment. Treat the RS-232 ground as a signal reference and route it with the interface conductors rather than treating it as an incidental chassis connection. This product page combines the ADM241L specification summary, documented drop-in alternatives, application guidance, and package-level design notes to help engineers evaluate the ADM241LJRZ for new and existing RS-232 interfaces.

RFQ پەیوەندی
ADM242AN - 200 kB/s 5 V RS-232 Transceiver | Analog Devices
ADM242AN

ADM242AN - 200 kB/s 5 V RS-232 Transceiver | Analog Devices

The Analog Devices ADM242AN is a 200 kB/s, 5 V RS-232 line transceiver with two drivers and two receivers in an 18-pin PDIP package. It uses an on-chip charge pump with 0.1 µF external capacitors to develop bipolar RS-232 levels, provides a 9 V output swing from a 5 V supply, and accepts receiver inputs up to 30 V. An RS-232 transceiver is an interface IC that combines voltage conversion, line drivers, and line receivers between CMOS-compatible logic and a differential-style, bipolar serial communications port. In the hierarchy of electronics, the ADM242AN belongs to interface ICs and data-interface converters, using charge-pump-assisted level shifting rather than an external negative power supply. The ADM242 family is designed for high-speed RS-232 links operating up to 200 kB/s from a single 5 V supply. Its two-driver, two-receiver arrangement supports full-duplex point-to-point communication, while the 9 V output swing and 30 V receiver input range provide useful margin for standard RS-232 implementations. The 0.1 µF charge-pump capacitors keep the external power-supply requirement compact. The device is identified as an EIA-232-E and V.28-compatible RS-232 interface in the verified manufacturer and distributor material. Its CMOS-based implementation avoids a separate external negative supply and integrates the charge-pump circuitry required to generate bipolar line-driver levels. The 18-pin PDIP package is a through-hole option for prototypes, legacy systems, and designs that prioritize easy inspection and hand soldering. Typical uses include serial adapters, industrial equipment links, test and measurement instruments, and legacy computer peripherals that need two RS-232 channels from one interface IC. The 200 kB/s rate is higher than many slower RS-232 transceivers, while the five-volt supply simplifies integration with digital logic. Designers should verify the ADM242AN package pinout and line-driver loading before layout. Keep charge-pump capacitor connections short, observe the required bypass and decoupling arrangement, and use protection appropriate to the cable environment because ESD and surge voltages on an external RS-232 port can exceed logic-level expectations. This product page synthesizes verified manufacturer and distributor information, comparison-oriented interface details, and practical implementation guidance for engineers evaluating the ADM242AN as a dual-driver, dual-receiver RS-232 solution.

RFQ پەیوەندی
ADM242ANZ - 200 kbps 2/2 RS-232 IC | Analog Devices
ADM242ANZ

ADM242ANZ - 200 kbps 2/2 RS-232 IC | Analog Devices

Analog Devices ADM242ANZ is a high-speed RS-232 line-driver and receiver IC featuring two drivers, two receivers, and a maximum signaling rate of 200 kB/s. It operates from a single 5 V supply in an 18-pin PDIP package and uses an on-chip charge pump with 0.1 µF external capacitors to generate the bipolar voltage levels required by RS-232 links. An RS-232 transceiver is an interface IC that combines digital line drivers and receivers for serial communication over unbalanced point-to-point connections. The driver converts TTL or CMOS logic signals into RS-232 bipolar levels, while the receiver converts bipolar line signals back into logic-level voltages. The ADM242ANZ belongs to the broader interface IC hierarchy, where it bridges modern digital logic and legacy serial equipment. The ADM242ANZ includes two drivers and two receivers, allowing two communication channels to be implemented with one device. Its 200 kB/s signaling rate supports higher-throughput serial links than slower RS-232 transceivers while retaining the broad compatibility of the RS-232 standard. The single 5 V supply simplifies system power design, and the charge-pump architecture avoids a separate negative supply for bipolar driver output. Two 0.1 µF charge-pump capacitors are required to operate the integrated voltage converter. According to the Analog Devices ADM242 family datasheet, the device meets EIA-232-E and V.28 specifications. This makes the interface appropriate for equipment requiring standardized RS-232 electrical behavior, including instrumentation, industrial control, data acquisition, and legacy peripheral connections. Typical uses include two-channel RS-232 links in test equipment, factory automation controllers, barcode and labeling systems, point-of-sale equipment, and embedded serial-port systems. The two-channel arrangement is particularly useful when a system needs both transmit and receive paths on each of two RS-232 ports while keeping the external component count low. When laying out a design, place the charge-pump capacitors close to their designated pins and provide a clean 5 V supply with local high-frequency bypass. RS-232 is an unbalanced interface, so cable routing and grounding can affect noise immunity. Confirm that the selected connector, cable, and remote equipment use compatible RS-232 signal levels before deployment. This page combines the verified ADM242ANZ specifications, package information, sourcing guidance, and practical interface-design considerations. It also distinguishes the available pin-compatible family option from broader functional equivalents, helping engineers assess replacement decisions without changing the PCB footprint.

RFQ پەیوەندی
ADM242AR - 200 kbps 2/2 RS-232 Transceiver | Analog Devices
ADM242AR

ADM242AR - 200 kbps 2/2 RS-232 Transceiver | Analog Devices

The Analog Devices ADM242AR is a 200 kbps, 5 V CMOS RS-232 interface IC with two drivers and two receivers in an 18-pin SOIC package. It accepts a 4.5 V to 5.5 V supply and uses an efficient on-chip charge pump with 0.1 µF external capacitors to produce the bipolar voltage levels required by RS-232. The 2/2 transceiver arrangement supports two transmit channels and two receive channels in one device. An RS-232 transceiver is an interface IC that converts low-voltage CMOS logic signals into voltage levels suitable for RS-232 links, while receivers convert the bipolar line levels back into CMOS-compatible signals. It belongs to the RS-232 transceiver hierarchy, alongside line drivers and line receivers, and is used in the broader category of interface ICs for point-to-point serial communication equipment. Key verified features include a maximum data rate of 200 kbps, operation from a single 5 V supply, two integrated drivers, two integrated receivers, and external charge-pump capacitors rated at 0.1 µF. The SOIC-18 package supports surface-mount assembly. The verified operating-temperature range is -40°C to +85°C, making the device suitable for industrial-temperature equipment when other system requirements are satisfied. The on-chip charge pump avoids a discrete negative-voltage supply and supports a compact interface implementation. In an RS-232 application, the CMOS-side pins connect to a UART or another serial controller, while driver outputs connect through the cable or board-level interface and receiver inputs accept the remote signal. The supply and charge-pump capacitor network must be placed according to the manufacturer datasheet because their stability and layout affect communication reliability. Typical uses include industrial serial adapters, instrumentation, data-acquisition equipment, embedded serial links, and control systems requiring more than one RS-232 direction. The ADM242AR is appropriate when two transmit and two receive channels are needed in one 5 V interface. Because its data rate is specified up to 200 kbps, cable length, termination, grounding, and connector requirements should be evaluated together with the UART baud rate. For new layouts, reserve all 18 package pins, connect the charge-pump capacitors as specified by Analog Devices, and provide a local bypass capacitor near the supply pins. The verified SOIC-18 footprint should be checked against the selected board and the exact ADM242AR pinout. Designers should confirm RS-232 electrical requirements, shutdown or enable behavior, and system-level ground strategy before release. This page combines the verified Analog Devices product description, distributor package and price references, and cross-reference results to help engineers evaluate the ADM242AR. It emphasizes verified facts and flags details that were not available in the supplied data rather than estimating missing electrical values.

RFQ پەیوەندی
ADM242ARZ - 200 kB/s RS-232 Transceiver | Analog Devices
ADM242ARZ

ADM242ARZ - 200 kB/s RS-232 Transceiver | Analog Devices

The Analog Devices ADM242ARZ is a high-speed RS-232 line transceiver with two drivers and two receivers, supporting transmission rates up to 200 kB/s from a single 5 V supply. The device uses 0.1 µF charge-pump capacitors to develop bipolar RS-232 levels and is packaged in an 18-lead SOIC for surface-mount assembly. It also includes shutdown and enable control functions for power-managed serial interfaces. An RS-232 transceiver is an interface IC that combines line drivers and line receivers into a complete logic-side-to-serial-port link. Within the hierarchy of interface ICs, RS-232 transceivers convert standard logic-level signals into differential-voltage, bipolar signaling and then recover the incoming serial data. The ADM242 family is designed for equipment requiring higher serial throughput than conventional RS-232 transceivers while retaining the familiar single-supply implementation. Key features include a maximum transmission rate of 200 kB/s, operation from one 5 V supply, two integrated drivers, and two integrated receivers. The on-chip charge pump requires only 0.1 µF external capacitors. According to the Analog Devices ADM242 product information, the circuit meets EIA-232-E and V.28 specifications and supports full-duplex RS-232 communication. Shutdown and enable controls add flexibility for systems that need to reduce supply current or manage peripheral power states. The charge-pump architecture raises the low-side driver output above the normal logic supply range, enabling approximately 9 V output swing with a 5 V supply. Receiver input levels extend to 30 V, supporting the wider voltage range associated with RS-232 ports. Because these are bipolar line signals, designers should protect exposed serial interfaces against surge, ESD, and accidental overvoltage conditions rather than treating every connector-side node as ordinary logic. Typical applications include industrial serial consoles, data-acquisition equipment, instrumentation, communications adapters, and embedded systems that exchange RS-232 data over cable runs. The 200 kB/s rate is suitable for moderate-speed control and diagnostic traffic, including configuration transfers and periodic status reporting. Systems requiring continuous data flow, very low power, or longer unrepeated distances should compare the interface requirements against the exact RS-232 timing, noise, and cable-loss limits. The principal design consideration is capacitor placement. Position the 0.1 µF charge-pump capacitors close to their designated pins and route the associated current paths carefully to minimize switching disturbance on sensitive circuitry. Place input and output protection components where cable-side connections enter the board, and confirm that the exposed metal package area has adequate copper for thermal dissipation and, where required, an exposed-pad connection. This page combines the manufacturer’s interface specifications, packaging information, practical application guidance, and a documented drop-in comparison to support faster design review and sourcing decisions. It also identifies where detailed pin assignments and procurement conditions must be checked directly against the Analog Devices datasheet and the Request a Quote form.

RFQ پەیوەندی
ADM2482EBRWZ - 2.5kV Isolated RS-485/RS-422 Transceiver | ADI
ADM2482EBRWZ

ADM2482EBRWZ - 2.5kV Isolated RS-485/RS-422 Transceiver | ADI

The Analog Devices ADM2482EBRWZ is a 2.5 kV rms isolated RS-485/RS-422 transceiver with integrated transformer driver, ±15 kV ESD protection, and 16 Mbps data rate, packaged in a 16-lead wide-body SOIC (SOIC-W). It combines a three-channel digital isolator, an RS-485/RS-422 differential line driver, and a differential line receiver on a single die, eliminating the need for an external DC/DC isolation supply by deriving bus-side power from an external center-tapped transformer. What is an isolated transceiver? An isolated transceiver is a type of interface IC that combines a galvanic isolation barrier with a standard serial communication protocol transceiver. It belongs to the broader family of digital isolators -> interface ICs -> wired communication transceivers -> semiconductors. The galvanic isolation (typically 2.5 kV rms or higher) protects low-voltage logic and host circuitry from large ground-potential differences, surge events, and fault voltages on long industrial bus segments. Isolated transceivers are essential when RS-485 cabling leaves the local equipment chassis and traverses factory floors, process plants, or outdoor installations. Key features of the ADM2482EBRWZ include a 25 kV/µs common-mode transient immunity (CMTI), 16 Mbps maximum data rate (suitable for PROFIBUS and high-speed half/full-duplex RS-485), configurable half-duplex or full-duplex operation, and a 3.3 V/5 V logic-side supply with a 3.3 V isolated bus-side supply generated internally from pins D1/D2 driving an external transformer. The wide-body SOIC package provides the required 8 mm creepage clearance for 2.5 kV rms reinforced isolation per IEC 61850 / IEC 61010-1 system standards. Hot-swap glitch rejection on the DE and RE pins prevents data corruption during board insertion into a live backplane. The transceiver uses an iCoupler-style transformer-driven isolation architecture: logic-side data crosses the isolation barrier through ADI's chip-scale micro-transformers, and bus-side power is rectified from a secondary winding. This architecture eliminates optocoupler LED aging concerns and provides stable timing across the industrial temperature range. The device operates over -40 °C to +85 °C ambient and meets ±15 kV ESD per IEC 61000-4-2 air-gap discharge on the bus pins. Typical applications include isolated RS-485 nodes in industrial fieldbus networks (PROFIBUS DP, Modbus RTU), smart-grid metering and substation communications, building automation (BACnet, KNX), solar inverter CAN/RS-485 links, and any system requiring robust high-voltage isolation between a controller and a remote bus segment. Half-duplex mode uses pins Y/Z/A/B; full-duplex mode uses dedicated TX and RX differential pairs. When designing with the ADM2482EBRWZ, pay attention to the center-tapped transformer selection: a 1:1.33 to 1:1.5 turns ratio with adequate isolation rating is recommended. Place the Schottky diodes and smoothing capacitor close to pins D1/D2 for clean bus-side power, and use 120 Ω termination at both ends of the RS-485 bus. The wide-body SOIC footprint requires an 8 mm minimum clearance under the package for 2.5 kV rms reinforced isolation. This page synthesizes distributor pricing, drop-in alternatives from the ADM2482E/ADM2487E family, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی