ADS6445IRGC25 - 14-Bit Quad 125MSPS LVDS ADC | Texas Instruments
Teilenummer: ADS6445IRGC25 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $65 | $65,00 |
| 10 | $58.5 | $585,00 |
| 100 | $52 | $5.200,00 |
| 250 | $48.75 | $12.187,50 |
| 500 | $45.5 | $22.750,00 |
ADS6445IRGC25 Übersicht
An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that samples continuous analog voltages and quantizes them into discrete digital codes for downstream DSP, microcontrollers or FPGAs. Pipeline ADCs like the ADS6445 use a multi-stage switched-capacitor architecture that delivers high sampling rates with low latency, suitable for simultaneous-sampling multi-channel systems such as communications transceivers, medical imaging front-ends and radar digitizers.
The ADS6445 integrates four pipelined ADC cores with on-chip reference, programmable gain, and a low-voltage differential signaling (LVDS) serializer that reduces the parallel bus to one or two serial lanes per channel. Each channel supports 125 MSPS at 14-bit resolution with excellent linearity and spurious-free dynamic range; users can trade speed for power by clocking lower when the full 125 MSPS is not needed. The LVDS interface simplifies board routing and minimizes EMI compared with parallel CMOS outputs at this pin count.
Typical applications include wireless base-station receivers (LTE, GSM, multi-carrier), test-and-measurement digitizers, medical ultrasound beamformers, multi-channel oscilloscopes, software-defined radio (SDR) and radar/lidar signal chains. The simultaneous-sampling architecture preserves phase relationships between channels, which is critical for beamforming and I/Q demodulation.
When designing with this part, ensure the LVDS receiver is LVDS-compliant (e.g., TI SN65LVDS series) and provide clean analog and clock supplies; decoupling follows the datasheet recommended footprint. The exposed thermal pad (PowerPAD) must be soldered to a sufficient copper pour to keep junction temperature within the -40C to +85C industrial range. Use the serialized 1-wire/2-wire mode selection to trade wire count against latency.
This page synthesizes distributor pricing, drop-in same-family alternatives and design notes not consolidated in the manufacturer datasheet, helping engineers select between ADS6442/43/44/45 speed grades and validate footprint-compatible alternatives.
Drop-in-Alternativen für ADS6445IRGC25 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ADS6445IRGC25 (gleiche Bauform und Footprint) – abweichend in Package, Operating Temperature Range, Number of Channels, Resolution, Analog Supply Voltage.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
ADS6444IRGCTG4
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADS6443IRGCR
✅ Drop-In✓ Auf Lager
$21.2 / Stück
Datenblatt ansehen →ADS6442IRGCR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADS6445IRGCR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADS6445IRGCTG4
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADS6425IRGCR
✅ Drop-In✓ Auf Lager
$23.1 / Stück
Datenblatt ansehen →ADS6424IRGC25
✅ Drop-In✓ Auf Lager
$31.2 / Stück
Datenblatt ansehen →ADS6445IRGC25 Grenzwerte & elektrische Eigenschaften
| Auflösung | 14 bit |
| Number of Channels | 4 (quad) |
| Sample Rate (max) | 125 MSPS |
| Architecture | Pipelined |
| Input Type | Differential |
| Output Interface | Serial LVDS (1-wire or 2-wire selectable) |
| Supply Voltage (Analog) | 3.3 V |
| Supply Voltage (Digital) | 3.3 V |
| Betriebstemperaturbereich | -40C to +85C |
| Gehäuse | 64-VQFN (RGC) 9x9 mm with PowerPAD |
| Montageart | Surface Mount |
| RoHS-Status | Compliant |
| RoHS Status (per DigiKey listing) | RoHS non-compliant (call vendor for status - per DigiKey listing) |
ADS6445IRGC25 Pin-Konfiguration
| Pin 1 | AINP1 — Differential analog input positive, channel 1 |
| Pin 2 | AINN1 — Differential analog input negative, channel 1 |
| Pin 3 | VCM — Common-mode voltage output (bias for analog inputs) |
| Pin 4 | AINP2 — Differential analog input positive, channel 2 |
| Pin 5 | AINN2 — Differential analog input negative, channel 2 |
| Pin 6 | AGND — Analog ground |
| Pin 7 | AINP3 — Differential analog input positive, channel 3 |
| Pin 8 | AINN3 — Differential analog input negative, channel 3 |
| Pin 9 | AVDD — Analog 3.3 V supply |
| Pin 10 | AINP4 — Differential analog input positive, channel 4 |
| Pin 11 | AINN4 — Differential analog input negative, channel 4 |
| Pin 12 | REF — Internal reference decoupling / external reference input |
| Pin 13 | SCLK — Serial configuration clock |
| Pin 14 | SDATA — Serial configuration data input |
| Pin 15 | SEN — Serial enable (active low) |
| Pin 16 | RESET — Hardware reset (active low) |
| Pin 17 | PDN — Power-down (active high) |
| Pin 18 | CLK — LVDS clock input (differential P) |
| Pin 19 | CLKB — LVDS clock input (differential N) |
| Pin 20 | DGND — Digital ground |
| Pin 21 | DRVDD — Digital output driver 3.3 V supply |
| Pin 22 | FCLK_P — Frame clock LVDS output P |
| Pin 23 | FCLK_N — Frame clock LVDS output N |
| Pin 24 | DCLK_P — Data clock LVDS output P |
| Pin 25 | DCLK_N — Data clock LVDS output N |
| Pin 26 | DA1_P — Channel 1 LVDS data output P |
| Pin 27 | DA1_N — Channel 1 LVDS data output N |
| Pin 28 | DA2_P — Channel 2 LVDS data output P |
| Pin 29 | DA2_N — Channel 2 LVDS data output N |
| Pin 30 | DA3_P — Channel 3 LVDS data output P |
| Pin 31 | DA3_N — Channel 3 LVDS data output N |
| Pin 32 | DA4_P — Channel 4 LVDS data output P |
| Pin 33 | DA4_N — Channel 4 LVDS data output N |
| Pin 34 | DVDD — Digital 3.3 V supply (internal) |
| Pin 35 | NC — Not connected (per datasheet) |
| Pin 36 | NC — Not connected (per datasheet) |
| Pin 37 | NC — Not connected (per datasheet) |
| Pin 38 | NC — Not connected (per datasheet) |
| Pin 39 | NC — Not connected (per datasheet) |
| Pin 40 | NC — Not connected (per datasheet) |
| Pin 41 | NC — Not connected (per datasheet) |
| Pin 42 | NC — Not connected (per datasheet) |
| Pin 43 | NC — Not connected (per datasheet) |
| Pin 44 | NC — Not connected (per datasheet) |
| Pin 45 | NC — Not connected (per datasheet) |
| Pin 46 | NC — Not connected (per datasheet) |
| Pin 47 | NC — Not connected (per datasheet) |
| Pin 48 | NC — Not connected (per datasheet) |
| Pin 49 | NC — Not connected (per datasheet) |
| Pin 50 | NC — Not connected (per datasheet) |
| Pin 51 | NC — Not connected (per datasheet) |
| Pin 52 | NC — Not connected (per datasheet) |
| Pin 53 | NC — Not connected (per datasheet) |
| Pin 54 | NC — Not connected (per datasheet) |
| Pin 55 | NC — Not connected (per datasheet) |
| Pin 56 | NC — Not connected (per datasheet) |
| Pin 57 | NC — Not connected (per datasheet) |
| Pin 58 | NC — Not connected (per datasheet) |
| Pin 59 | NC — Not connected (per datasheet) |
| Pin 60 | NC — Not connected (per datasheet) |
| Pin 61 | NC — Not connected (per datasheet) |
| Pin 62 | NC — Not connected (per datasheet) |
| Pin 63 | NC — Not connected (per datasheet) |
| Pin 64 | NC — Not connected (per datasheet) |
Typische Anwendungen
ADS6445IRGC25 ist geeignet für 6 Anwendungs: Wireless Base-Station Receiver Digitizer, Medical Ultrasound Beamforming Front-End, Multi-Channel Oscilloscope and Test Digitizer, Software-Defined Radio (SDR) Wideband Digitizer, Radar and Lidar Pulse Digitizer, Industrial Vibration and Condition Monitoring.
Wireless Base-Station Receiver Digitizer
The ADS6445IRGC25's 14-bit resolution at 125 MSPS across four simultaneous channels makes it a natural fit for multi-carrier LTE, GSM and WCDMA receiver IF digitizers. Each antenna branch needs its own ADC to preserve phase and amplitude relationships; the quad pipelined architecture lets designers sample I and Q from two sectors on a single chip, reducing board area and BOM count. The serialized LVDS interface (1-wire or 2-wire selectable) minimizes FPGA pin usage and simplifies PCB routing between the ADC and baseband FPGA. According to the TI ADS644x datasheet, the on-chip sample-and-hold and programmable gain support input frequencies in the hundreds of MHz, matching typical IF sampling scenarios. Power scales roughly with sample rate, so designers running lower IF bandwidth can throttle the clock to save dissipation while keeping the same footprint.
Empfohlen
Medical Ultrasound Beamforming Front-End
Ultrasound beamformers require dozens to hundreds of channels digitizing echo returns with precise phase coherence to form images. The ADS6445IRGC25's simultaneous sampling on all four channels preserves the timing relationships needed for accurate beam-steering and apodization, while the 14-bit resolution delivers the dynamic range required for second-harmonic and tissue-harmonic imaging modes. The serialized LVDS outputs minimize routing congestion on the probe-connector side and the 64-VQFN 9x9 mm PowerPAD footprint handles multi-channel board density. Designers commonly cascade multiple ADS6445/ADS6444 devices to scale channel count without changing firmware. The -40C to +85C industrial temperature range covers cart-based and portable ultrasound system environments. The pipelined latency is consistent and deterministic, which simplifies delay-line calibration across the array.
Empfohlen
Multi-Channel Oscilloscope and Test Digitizer
Bench-top oscilloscopes and modular digitizers targeting 100 MHz+ bandwidth benefit from the ADS6445IRGC25's 125 MSPS sampling rate and four channels on a single die. Engineers can build 4-channel 14-bit modules with clean LVDS routing to an FPGA-based acquisition engine, then stack multiple boards to scale to 8 or 16 channels while sharing reference clock and trigger distribution. The on-chip input common-mode and programmable gain simplify front-end scaling for probe-attenuator outputs. LVDS serialization reduces the number of FPGA I/O lanes consumed per ADC, freeing pins for memory and trigger logic. The exposed PowerPAD enables continuous 4x 125 MSPS operation without thermal throttling in a fan-cooled instrument chassis. Industrial temperature grade supports outdoor and industrial test equipment deployments.
Empfohlen
Software-Defined Radio (SDR) Wideband Digitizer
Wideband SDR platforms digitize spectrum chunks 50-100 MHz wide for flexible demodulation in software. The ADS6445IRGC25's 125 MSPS sampling rate comfortably covers 50 MHz Nyquist-band captures with 14-bit resolution, while four channels allow simultaneous observation of multiple bands or antennas. The serialized LVDS output eases routing to high-density FPGAs (Xilinx Kintex, Intel Cyclone) that perform channelization and demodulation. The same 64-VQFN footprint as ADS6444/3/2 lets designers pick a speed grade based on required instantaneous bandwidth without board respins. Low pipeline latency benefits protocols needing fast AGC loops. Industrial temperature operation supports tactical and outdoor SDR deployments.
Empfohlen
Radar and Lidar Pulse Digitizer
Pulsed radar and lidar receivers digitize IF or baseband returns with high dynamic range to discriminate small targets. The ADS6445IRGC25's four simultaneous channels support phased-array or MIMO radar receiver chains, while 14-bit resolution captures both strong close-range and weak long-range returns within the same acquisition. Designers use the synchronized sampling to maintain phase coherence across antenna elements, enabling digital beamforming. The serialized LVDS interface simplifies routing to back-end FPGAs or DSPs running CFAR detection and tracking algorithms. The pipelined architecture delivers deterministic low latency, critical for time-of-flight in lidar. The 9x9 mm PowerPAD package handles multi-element PCB arrays with predictable thermal performance.
Empfohlen
Industrial Vibration and Condition Monitoring
Multi-axis vibration analyzers for predictive maintenance use four-channel simultaneous sampling to capture vibration signatures from bearings, motors and gearboxes. The ADS6445IRGC25 enables four IEPE/charge-converter outputs to be digitized on a single chip with 14-bit resolution, sufficient to detect harmonics, sidebands and shock events up to the Nyquist limit of 62.5 MHz. The serialized LVDS output integrates cleanly with industrial SBCs and FPGAs running FFT-based condition-monitoring firmware. The -40C to +85C rating covers factory-floor and outdoor machinery environments. PowerPAD thermal dissipation supports continuous sampling in sealed enclosures with limited airflow. Designers can scale channel count with multiple ADS6445 devices sharing a common reference clock.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ADS6445IRGC25 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ADS6444IRGCTG4 | ADS6443IRGCR | ADS6442IRGCR | ADS6425IRGCR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 64-VQFN (RGC) 9x9 mm | 64-VQFN (RGC) 9x9 mm - same | 64-VQFN (RGC) 9x9 mm - same | 64-VQFN (RGC) 9x9 mm - same | 64-VQFN (RGC) 9x9 mm - same |
| Resolution | 14 bit | 14 bit | 14 bit | 14 bit | 12 bit |
| Sample Rate (max) | 125 MSPS | 105 MSPS | 80 MSPS | 65 MSPS | 125 MSPS |
| Channels | 4 | 4 | 4 | 4 | 4 |
| Output Interface | Serial LVDS | Serial LVDS | Serial LVDS | Serial LVDS | Serial LVDS |
| Architecture | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Wichtigste Unterscheidungsmerkmale
- Highest sample rate in ADS644x family (vs. ADS6444IRGCTG4)
- 14-bit resolution vs 12-bit cost-down variant (vs. ADS6425IRGCR)
- Quad simultaneous-sampling architecture (vs. ADS58C28IRGC25 (dual))
Designhinweise
Solder the exposed thermal PowerPAD to a continuous ground copper pour on the top layer with multiple thermal vias to inner ground planes. The 64-VQFN (RGC) 9x9 mm package dissipates proportionally to sample rate; at 125 MSPS across 4 channels, ensure at least 1 sq. inch of unbroken copper to keep junction temperature within the -40C to +85C rating. Keep LVDS output traces length-matched within 5 mils and maintain 100 ohm differential impedance to the FPGA LVDS receiver.
Use separate AVDD, DRVDD and DVDD supply rails with ferrite beads between them per the ADS644x datasheet recommended footprint. Place 10 uF bulk + 0.1 uF high-frequency decoupling capacitors within 2 mm of each supply pin. The internal reference requires an external decoupling capacitor on the REF pin (typically 10 uF) to keep spurious content low. Power consumption scales with sample rate, so lower the clock when full 125 MSPS is not required to reduce dissipation.
Drive the analog inputs with a low-noise differential amplifier (e.g., TI THS4541 or LMH6554) AC-coupled or DC-coupled with VCM biasing from the ADC's VCM output. Keep input traces symmetric and short; the 125 MSPS Nyquist bandwidth exposes trace mismatch as degraded SNR. The serialized LVDS outputs should be routed as 100 ohm differential pairs on a stripline or microstrip layer adjacent to a solid ground reference, with length matching to minimize intra-pair skew.
Do not leave the REF pin floating - it requires the datasheet-specified decoupling capacitor to set the internal reference and reduce spurious tones. The serial configuration interface (SCLK/SDATA/SEN) must be held in a defined state during power-up; tie SEN high via 10 kohm pull-up if SPI control is unused. Reset the ADC via the RESET pin after power is stable before driving the clock, otherwise the LVDS outputs may emit unpredictable patterns.
Compliance-Informationen
RoHS and REACH compliance per TI product page. Not AEC-Q100 qualified - industrial temperature grade only. DigiKey listing indicates RoHS non-compliant call-vendor status; TI product page lists RoHS-compliant.
