LM224KDG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments
N.º de pieza: LM224KDG4 ✓ ActivoLM224KDG4 Descripción general
An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify small voltage differences. The LM224 belongs to the operational-amplifier hierarchy and provides four amplifier channels in one quad package. Each channel can amplify sensor, audio, or feedback signals independently. Internal frequency compensation makes the devices suitable for closed-loop designs without external compensation networks, although the available datasheet information should guide stability and unity-gain layout decisions.
The LM224KDG4 combines four general-purpose amplifier channels with a maximum supply voltage of 30 V. Its 1.2 MHz gain-bandwidth product supports signal paths extending from low-frequency measurement circuits to moderate-bandwidth audio and control applications. The reported input offset voltage is 3 mV, a parameter that contributes to DC error when the amplifier operates near its input limits or in precision current-feedback measurements.
The K suffix identifies an industrial temperature grade covering -25 °C to +85 °C. The four circuits share a common supply arrangement but otherwise operate independently, allowing one package to implement summing, buffering, amplification, filtering, or current-feedback stages. A listing identifies the device as a 14-SOIC surface-mount part with gull-wing terminals, while the ordering code G4 denotes its supplied packaging configuration.
Typical uses include industrial process-signal conditioning, low-frequency sensor interfaces, audio preamplification, feedback networks in power converters, and general control systems. Four channels in one package can reduce PCB area and simplify multi-amplifier analog boards. The 30 V supply capability also accommodates industrial rails higher than conventional 5 V or 12 V systems, subject to the common-mode and output-swing limits stated in the manufacturer datasheet.
PCB layout should keep input, feedback, and decoupling connections short, place the bypass capacitor close to the supply pins, and route sensitive input nodes away from switching and high-current paths. Because the LM224K is not rail-to-rail, verify input and output voltage ranges before choosing it for single-supply sensing near ground. This page combines package, temperature, bandwidth, and cross-reference information with practical guidance for evaluating same-footprint replacements.
Alternativas directas para LM224KDG4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con LM224KDG4 (mismo factor de forma y huella) — difiere en Package.
LM224KAD
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM224KDR
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →LM224KP
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
LM224DR
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$0.1641 / unidad
Ver hoja de datos →LM224D
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →LM224KDG4 Valores máximos y características eléctricas
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Amplifier Channels | 4 circuits |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 3 mV |
| ESD Protection | 2 kV |
| Rango de temperatura de funcionamiento | -25 °C to +85 °C |
| Encapsulado | 14-pin SOIC |
| Terminal Count | 14 terminals |
| Tipo de montaje | Surface mount |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Estado RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Guía de configuración de pines de LM224KDG4 rectangular
Configuración de pines para LM224KDG4 (encapsulado rectangular). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para LM224KDG4.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
LM224KDG4 es adecuado para 6 aplicacións: Industrial Sensor Signal Conditioning, Audio Preamplification, Power Supply Feedback Control, Process Control Loops, Data Acquisition Front Ends, Motor and Actuator Control.
Industrial Sensor Signal Conditioning
The LM224KDG4 is well suited to conditioning low-level industrial sensor signals because its four independent channels can amplify, buffer, and stage multiple inputs within one 14-pin SOIC package. The 1.2 MHz gain-bandwidth product provides useful bandwidth for common temperature, pressure, and position sensing paths, while the 30 V supply rating supports higher-voltage industrial control systems. Use two channels for sensor conditioning and the remaining channels for reference buffering or active filtering. Verify the input common-mode range against the sensor output because this general-purpose amplifier is not specified as rail-to-rail.
Recomendado
Audio Preamplification
The LM224KDG4 can implement four moderate-bandwidth audio preamplifier or mixer channels in a compact circuit. Its 1.2 MHz gain-bandwidth product is substantially above typical audio-bandwidth requirements, and the quad configuration allows left and right channels to be amplified while the other channels support gain or buffer stages. The 30 V maximum supply rating permits operation from elevated single rails when the circuit and output-swing requirements permit it. Because the device is not rail-to-rail, the designer should check output swing and input bias behavior in the selected gain network.
Recomendado
Power Supply Feedback Control
The LM224KDG4 can provide error amplification and feedback functions in industrial power-control systems because four channels are available in one package. Its 1.2 MHz bandwidth is suitable for moderate-speed feedback loops and its 30 V supply rating allows connection to higher-voltage control circuitry where appropriate. A practical allocation might use one channel for the error amplifier, one for output-voltage buffering, and two for current sensing or fault-path conditioning. The final loop compensation and stability network must be selected using the LM224K datasheet and the power-stage characteristics.
Recomendado
Process Control Loops
The LM224KDG4 fits process-control boards that require several conditioning channels around a controller. Each of the four amplifiers can handle a separate sensor input, actuator feedback signal, or buffered reference within a system operating from an elevated industrial rail. The 30 V maximum supply rating and -25 °C to +85 °C operating range align with many factory environments, while the 1.2 MHz gain-bandwidth product covers many slow control signals. Common-mode range, output swing, and stability must be checked for every loop rather than inferred from the family headline specifications.
Recomendado
Data Acquisition Front Ends
The LM224KDG4 can implement multiple input-buffer or gain stages ahead of an analog-to-digital converter in a low-frequency data-acquisition system. Four channels in one 14-pin SOIC reduce package count, and 1.2 MHz bandwidth is adequate for many temperature, pressure, and instrumentation signals rather than high-speed waveform capture. Use short feedback paths and verify settling behavior at the required gain. The amplifier should be bypassed close to its supply pins, and sensitive inputs should remain away from switching regulators and digital clock lines to minimize coupled noise.
Recomendado
Motor and Actuator Control
The LM224KDG4 can provide error amplification, current-loop feedback, and input conditioning around industrial actuator-control circuits. Its quad organization makes it practical to implement several related analog functions in a compact controller, and its 30 V supply rating accommodates elevated control rails better than standard 5 V-only devices. The 1.2 MHz bandwidth is appropriate for many low- and moderate-bandwidth actuator loops. Designers must verify output current, output swing, input common-mode limits, and stability, and should keep power-stage switching nodes separated from sensitive amplifier inputs.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LM224KDG4 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LM224KAD | LM224KDR | LM224KP | LM224DR | LM224D |
|---|---|---|---|---|---|---|
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Channels | 4 | 4 | 4 | 4 | 4 | 4 |
| Maximum Supply Voltage | 30 V | 30 V | 30 V | 30 V | 30 V | 30 V |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Diferenciadores clave
- Four amplifiers in one 14-pin SOIC package (frente a LM224KAD)
- Matches the 30 V and 1.2 MHz core operating ratings (frente a LM224KDR)
- Designed for a documented industrial operating range (frente a LM224DR)
Notas de diseño
Place the supply-bypass capacitor immediately adjacent to the device supply pins, and keep each amplifier's input and feedback traces short. The four channels share package power and ground connections, so common-impedance effects can couple disturbance between channels. Route sensitive inputs away from switching-regulator outputs, power inductors, motor phases, and high-current return paths. The 1.2 MHz gain-bandwidth product makes trace length and parasitic capacitance more relevant as closed-loop gain rises.
Do not assume that the 30 V maximum supply rating permits full 30 V signal swing or rail-to-rail operation. Before using the LM224KDG4 with a sensor whose output approaches ground, verify the input common-mode range and output-swing limits in the manufacturer datasheet. Also confirm that the selected LM224 orderable variant maintains the required -25 °C to +85 °C operating range and the same 14-pin SOIC footprint.
Estimated: four amplifiers can make total supply-current demand more significant than that of a single-channel circuit. Calculate worst-case supply current using the maximum channel-current specification in the LM224K datasheet, multiply it by four, add bias and load requirements, and size the regulator and copper paths accordingly. Because this is a linear amplifier, heat rise also depends on total channel dissipation and the board's thermal resistance.
Use short, direct feedback components and avoid routing inputs near the exposed traces of adjacent channels. When operating at higher closed-loop gains, verify stability with the intended feedback network, source impedance, load capacitance, and board parasitics. The family is internally frequency compensated, but compensation does not remove the need to validate the final gain, bandwidth, and capacitive-loading combination.
Información de cumplimiento
No explicit environmental or automotive compliance statements were identified for LM224KDG4. The industrial temperature grade does not by itself imply AEC-Q100 qualification.