LM324AWDT - Low-Power Quad Op Amp | STMicroelectronics
N.º de pieza: LM324AWDT ✓ ActivoLM324AWDT Descripción general
An operational amplifier is an analog voltage amplifier whose gain, filtering, buffering, and feedback behavior are determined mainly by external components. The LM324 belongs to the general-purpose amplifier hierarchy: op amp, analog amplifier, signal-conditioning IC, and ultimately semiconductor. A quad package contains four amplifiers that may be used independently or together for instrumentation, control, filtering, and signal conversion.
The LM324 family is designed for low power consumption and low input bias current. Internally compensated operation simplifies closed-loop design because no external compensation network is required for typical voltage-feedback use. The four amplifiers are independent, allowing simultaneous sensing and actuation, although the common supply pins mean that all four channels share the same supply-voltage and ground references.
The A designation identifies a distinct qualification or ordering configuration within the LM324 family, while W indicates tape-and-reel packaging and DT identifies the 14-pin small-outline package. Engineers should confirm the exact temperature limits, electrical limits, and qualification status for the selected ordering code in the STMicroelectronics datasheet before using the device in a regulated end application.
Typical uses include low-frequency sensor conditioning, feedback control loops, active filters, audio and communication signal paths, and general analog instrumentation. In a 5 V single-supply system, the common reference arrangement and input/output swing limits remain central design constraints. In split-supply circuits, the device is particularly useful when the signal can swing around 0 V.
Keep input and output voltages within the absolute maximum ratings, observe the input common-mode range, and provide stable bypass capacitance near the supply pins. Because the LM324 is intended mainly for general-purpose and low-frequency work, designs requiring wide input swing, very low offset, high speed, rail-to-rail output, or low-noise performance should compare the exact datasheet limits against precision or modern amplifier families.
This page combines the LM324AWDT family identity, package information, qualification distinctions, drop-in ordering options, application guidance, and practical design considerations in a format designed to help engineers evaluate replacements without overlooking the electrical differences between ordering codes.
Alternativas directas para LM324AWDT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con LM324AWDT (mismo factor de forma y huella) — difiere en Amplifier Type, Package, Input Bias Current, Power Consumption.
LM324WDT
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM324ADT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
LM324DT
✅ Sustitución directa✗ Sin stock
$0.0827 / unidad
Ver hoja de datos →LM324AWDT Valores máximos y características eléctricas
| Number of Amplifiers | 4 channels |
| Amplifier Type | 1 general-purpose operational amplifier |
| Tensión de alimentación | ±15 V (30 V total span) |
| Power Consumption | Low power |
| Input Bias Current | Low input bias current |
| Frequency Compensation | Internal |
| Encapsulado | 14-pin SO package |
| Packaging | Tape and reel |
| Tipo de montaje | Surface mount |
Configuración de pines de LM324AWDT
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | IN1- — Amplifier 1 inverting input |
| Pin 3 | IN1+ — Amplifier 1 non-inverting input |
| Pin 4 | V+ — Positive supply voltage |
| Pin 5 | IN2+ — Amplifier 2 non-inverting input |
| Pin 6 | IN2- — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | OUT3 — Amplifier 3 output |
| Pin 9 | IN3- — Amplifier 3 inverting input |
| Pin 10 | IN3+ — Amplifier 3 non-inverting input |
| Pin 11 | V- — Ground or negative supply connection |
| Pin 12 | IN4+ — Amplifier 4 non-inverting input |
| Pin 13 | IN4- — Amplifier 4 inverting input |
| Pin 14 | OUT4 — Amplifier 4 output |
Aplicaciones típicas
LM324AWDT es adecuado para 6 aplicacións: Industrial Sensor Signal Conditioning, Audio Preamplifier and Mixing Stage, Power Supply Feedback Control, Active RC Filtering, Communication Interface Buffering, Test and Measurement Front End.
Industrial Sensor Signal Conditioning
The LM324AWDT is appropriate for low-frequency sensor-conditioning stages because four independent amplifiers can buffer, scale, and subtract sensor signals within one 14-pin SO package. Its low-power operating characteristic and internally compensated voltage-feedback architecture simplify analog front ends built around resistive dividers and RC networks. A practical arrangement places one channel as a unity-gain input buffer, another as an inverting amplifier, and the remaining channels for gain and offset stages. The confirmed capability to operate at ±15 V supports split-supply instrumentation, but input common-mode range, output swing, offset, bias current, bandwidth, and slew rate must be checked against the sensor output and required measurement bandwidth.
Recomendado
Audio Preamplifier and Mixing Stage
The LM324AWDT can implement low-frequency audio preamplification, channel mixing, and active feedback stages where broad availability and low power consumption are more important than low-noise or high-bandwidth performance. Four amplifiers provide enough channels for a mono amplifier, stereo preamp, or small mixer without using four separate packages. Each channel should use negative feedback to establish its closed-loop gain, while the input and output networks must remain inside the confirmed input common-mode and output-swing limits. The 30 V total supply capability supports split-supply audio boards, but designers should verify slew rate and bandwidth for the highest audio frequency and avoid using this general-purpose amplifier where low-noise or rail-to-rail requirements dictate a more specialized part.
Recomendado
Power Supply Feedback Control
The LM324AWDT can form the error amplifier, voltage-feedback divider, and current-feedback elements in a basic regulated supply, provided the control-loop bandwidth and output requirements are compatible. Its four independent channels allow a single package to combine the main regulation amplifier with auxiliary limiting, soft-start, or monitoring functions. A practical design should compensate the loop for the selected output capacitor and load range, while keeping the amplifier input and output inside the usable signal limits. Because the LM324 is a general-purpose amplifier rather than a dedicated regulator controller, ripple, transient response, stability margins, and load-current capability require careful calculation. The confirmed ±15 V capability is useful for higher-voltage feedback networks, but absolute maximum and common-mode limits must be observed.
Recomendado
Active RC Filtering
The LM324AWDT is suitable for first-order and many second-order active filters built with passive R and C networks, including low-pass, high-pass, and band-pass stages. Internally compensated voltage-feedback operation reduces the number of components required for stable closed-loop gain, while four channels permit multistage filtering without multiple IC packages. Component tolerances directly determine cutoff accuracy, so use resistor networks with suitable matching and account for amplifier offset and bias-current errors when filtering very small signals. The confirmed ±15 V operating capability makes split-supply biasing straightforward for bipolar audio or instrumentation signals. Verify gain-bandwidth product and slew rate against the filter's upper frequency, and confirm that signals remain inside the amplifier's input common-mode and output-swing ranges.
Recomendado
Communication Interface Buffering
The LM324AWDT can buffer slow analog communication, level-conversion, and interface signals when the circuit operates within the amplifier's general-purpose electrical limits. Four channels can support bidirectional sensing, transmit-monitor amplification, offset adjustment, and receive amplification in a compact analog interface. The implementation should use the confirmed supply arrangement for the logic and signal levels, include protection where transients can exceed input limits, and avoid pushing outputs beyond the available swing. The low input bias current is useful when driving high-impedance sources, but source impedance, input capacitance, and bandwidth still determine actual settling behavior. Verify common-mode range at every logic threshold and compare the amplifier's response time with the interface data rate before relying on the part for high-speed digital buffering.
Recomendado
Test and Measurement Front End
The LM324AWDT can support inexpensive test and measurement front ends that require several precision-enough general-purpose amplifiers for buffering, differential amplification, gain adjustment, and output driving. Its four-channel arrangement minimizes board space, while low input bias current helps when the source impedance is relatively high. For laboratory or production equipment, begin by checking the confirmed temperature grade, input offset voltage, input bias current, gain-bandwidth product, slew rate, and output-current capability against the measurement accuracy and bandwidth. Decouple the supply pins locally and use guarding or shielding around high-impedance inputs to reduce leakage and pickup. The device is most appropriate for low-to-moderate frequency measurements where a modern rail-to-rail precision amplifier is not required by the signal range.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LM324AWDT — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LM324WDT | LM324ADT | LM324DT |
|---|---|---|---|---|
| Package | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Number of Amplifiers | 4 channels | 4 channels | 4 channels | 4 channels |
| Amplifier Class | Low-power general-purpose operational amplifier | Low-power general-purpose operational amplifier | Low-power general-purpose operational amplifier | Low-power general-purpose operational amplifier |
| Compensation | Internal frequency compensation | Internal frequency compensation | Internal frequency compensation | Internal frequency compensation |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
| Shipping Format | Tape and reel | Tape and reel | Tube or tray ordering dependent | Tube or tray ordering dependent |
Diferenciadores clave
- Four-channel integration in one 14-pin package (frente a LM2902KNS)
- Internal frequency compensation (frente a LM324WDT)
- Single-package implementation for four analog channels (frente a LM2902KNS)
Notas de diseño
Place the supply bypass capacitor as close as practical to pins 4 and 11, and keep the high-current return path short to reduce supply noise and ground bounce. Route each input connection away from output and switching-node traces. Because the LM324 contains four amplifiers in one package, shared supply impedance can couple noise between channels; separate local bypass paths and solid ground-plane connectivity help preserve channel-to-channel isolation.
Do not assume the full supply rail is available at the output. Check the output-swing limits at the required load current and ensure both inputs remain inside the common-mode range throughout signal excursions. A ±15 V supply does not automatically provide ±15 V signal swing, and an input signal above the common-mode limit can produce distortion or unexpected output behavior even though the absolute maximum supply rating is satisfied.
Use negative feedback to establish the required closed-loop gain and confirm that the selected gain does not exceed the amplifier's bandwidth and stability behavior at the operating frequency. Avoid capacitively loading the output with long cable runs or slow input nodes without checking for oscillation. For high-impedance sources, minimize board leakage and contamination around the input pins because bias current and leakage errors can dominate the measurement.
Estimated: with a 30 V total supply span and a 15 V output at 10 mA load, the ideal linear-stage dissipation is (30 V - 15 V) × 0.01 A = 0.15 W. Actual device dissipation also depends on quiescent current and output stage behavior. This estimate indicates that a small SO package can be adequate in moderate-load applications, but the exact maximum ratings, quiescent current, output current, and thermal characteristics must be verified for the final operating condition.
Información de cumplimiento
The A ordering-code comparison references RoHS and REACH information, but no explicit compliance result was available for extraction. Confirm the exact declarations in the STMicroelectronics product documentation and material declaration.