MCP3426A1-E/SN - 16-Bit Dual-Channel ADC | Microchip
N.º de pieza: MCP3426A1-E/SN ✓ ActivoMCP3426A1-E/SN Descripción general
A delta-sigma analog-to-digital converter is an ADC category that uses delta-sigma modulation and digital filtering to convert analog voltage into high-resolution digital codes. The MCP3426 belongs to the ADC → delta-sigma ADC → data-converter IC hierarchy. It is designed for precision measurement systems where differential inputs, low noise, accurate conversion, and a simple I2C interface are more important than very high sampling speed.
Key features include two differential analog input channels, resolution of up to 16 bits, and a 15 Hz conversion rate. The integrated 2.048 V reference removes the need for an external reference source, while the differential inputs help reject common-mode noise when sensing small signals. The device operates from 2.7 V to 5.5 V and communicates through I2C, making it suitable for embedded measurement systems with a microcontroller or sensor hub.
The MCP3426 family combines a low-noise, high-accuracy delta-sigma conversion stage with an internal precision reference and programmable conversion and gain behavior. The A1 device variant uses a factory-programmed I2C address, allowing deterministic bus addressing without external address straps. Differential input architecture also supports ratiometric or referenced sensor measurements when both input nodes are driven from the same excitation source.
Typical uses include industrial process measurement, battery-powered environmental sensing, strain-gauge instrumentation, pressure-sensor interfaces, and low-speed data acquisition. Its 15 Hz conversion rate is well suited to slowly changing physical variables rather than waveform capture or high-bandwidth communications. The two channels can also be configured for single-ended operation when the application does not require a fully differential signal path.
For PCB design, keep analog input traces short and place the input bypass components close to their associated pins. Provide clean return paths beneath the analog section and isolate the I2C routing from sensitive input nodes. The ADC must also be evaluated for gain, common-mode range, input filtering, reference accuracy, and system noise before the conversion output is interpreted as a precision measurement.
Alternativas directas para MCP3426A1-E/SN — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MCP3426A1-E/SN (mismo factor de forma y huella) — difiere en Package, Operating Temperature Range, ADC Type, Differential Input Range, Number of Input Channels.
MCP3426A2-E/SN
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MCP3426A3-E/SN
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MCP3426A4-E/SN
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MCP3426A5-E/SN
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MCP3426A6-E/SN
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MCP3426A7-E/SN
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MCP3426A1-E/SN Valores máximos y características eléctricas
| ADC Type | Delta-sigma ADC |
| Resolución | Up to 16 bits |
| Number of Input Channels | 2 |
| Input Type | Differential |
| Conversion Rate | 15 samples/s |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | ±2.048 V differential |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Interfaz | I2C |
| Encapsulado | 8-pin SOIC, 0.154 in (3.90 mm) wide |
| Tipo de montaje | Surface mount |
| Noise Performance | Low noise |
| Conversion Accuracy | High accuracy |
| I2C Address | 0x48 factory-programmed for MCP3426A1 |
| Estado RoHS | Unknown |
| REACH Status | Unknown |
Configuración de pines de MCP3426A1-E/SN
| Pin 1 | SCL — I2C clock input |
| Pin 2 | SDA — I2C data input and output |
| Pin 3 | VREF — Reference voltage input or internal reference connection |
| Pin 4 | VDD — Positive supply voltage |
| Pin 5 | VIN0+ — Channel 0 non-inverting analog input |
| Pin 6 | VIN0- — Channel 0 inverting analog input |
| Pin 7 | VIN1- — Channel 1 inverting analog input |
| Pin 8 | VIN1+ — Channel 1 non-inverting analog input |
Aplicaciones típicas
MCP3426A1-E/SN es adecuado para 6 aplicacións: Industrial Pressure Sensor Interface, Strain Gauge Instrumentation, Environmental Monitoring, Battery-Powered Sensor Node, Precision Process Monitoring, Portable Measurement Instrument.
Industrial Pressure Sensor Interface
The MCP3426A1-E/SN suits low-speed bridge or ratiometric pressure-sensor measurements because it accepts two differential input channels, provides up to 16-bit resolution, and operates at 15 sample/s. Connect the sensor excitation and bridge output so common sensor noise and supply variation are rejected. The internal 2.048 V reference supports a ±2.048 V differential range, while the 2.7 V to 5.5 V supply range accommodates common industrial rails. An input RC filter can suppress high-frequency interference, and the converter's I2C output allows the host controller to read settled measurements without continuously clocking a high-rate converter.
Recomendado
Strain Gauge Instrumentation
MCP3426A1-E/SN can digitize millivolt-level strain-gauge changes when both differential inputs remain within the supported common-mode range and the bridge output is suitably conditioned. Its differential conversion architecture rejects equal-magnitude noise on the two input nodes, while the low-noise 16-bit delta-sigma core supports precise static-force or slow-deformation measurements. The 15 sample/s rate is appropriate for load cells, force sensing, and structural monitoring. Use a low-noise bridge excitation, matched input filtering, and a solid ground strategy to preserve the small differential signal before conversion.
Recomendado
Environmental Monitoring
The MCP3426A1-E/SN is appropriate for slowly varying environmental signals such as temperature, humidity, gas concentration, and light levels when the sensor output is compatible with the ±2.048 V differential range. Its 15 sample/s rate provides more than enough throughput for periodic environmental readings, while up-to-16-bit resolution can retain useful detail in slowly changing signals. The internal 2.048 V reference reduces external reference complexity, and the two differential channels allow paired sensing or sensor-plus-reference measurements. The host can read through I2C and apply calibration or compensation in firmware.
Recomendado
Battery-Powered Sensor Node
MCP3426A1-E/SN fits low-duty-cycle battery-powered sensor nodes because it supports a 2.7 V to 5.5 V supply range and is designed for low-noise precision conversion rather than high-rate sampling. The host controller can keep the sensor powered, start a conversion, wait for the 15 sample/s measurement cadence, and transmit the processed value. Differential inputs help reject noise shared by both sensor lines. Because the converter is not intended for waveform acquisition, power-management decisions should focus on sensor duty cycle, board leakage, reference settling, and the number of channels that must remain active.
Recomendado
Precision Process Monitoring
MCP3426A1-E/SN can serve as the measurement ADC in a process-control front end for slow pressure, flow, level, or chemical signals. Differential conversion is valuable when a transmitter outputs a small signal relative to its supply or common-mode voltage, and the 2.048 V internal reference provides a defined conversion basis. Two channels support sequential acquisition, while the 15 sample/s rate suits process variables that evolve more slowly than industrial communication cycles. Firmware can perform gain, offset, and temperature compensation before transmitting the corrected engineering value to supervisory control equipment.
Recomendado
Portable Measurement Instrument
MCP3426A1-E/SN is useful in portable laboratory and field instruments that measure low-level analog quantities with limited board area. The 8-pin SOIC package simplifies assembly, the internal reference limits external components, and the I2C interface allows economical connection to a display controller or embedded processor. Its two differential channels can acquire a measurement and a reference or support two related sensor inputs. The 15 sample/s conversion rate aligns with stable handheld readings, while the up-to-16-bit resolution and differential architecture help preserve accuracy in systems where sensor leads and ground offsets can degrade low-level measurements.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MCP3426A1-E/SN — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MCP3426A2-E/SN | MCP3426A3-E/SN | MCP3426A4-E/SN | MCP3426A5-E/SN | MCP3426A6-E/SN | MCP3426A7-E/SN |
|---|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Resolution | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Conversion Rate | 15 samples/s | 15 samples/s | 15 samples/s | 15 samples/s | 15 samples/s | 15 samples/s | 15 samples/s |
| Internal Reference | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V |
| Differential Input Range | ±2.048 V | ±2.048 V | ±2.048 V | ±2.048 V | ±2.048 V | ±2.048 V | ±2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Factory-Programmed I2C Address | 0x48 | 0x49 | 0x4A | 0x4B | 0x4C | 0x4D | 0x4E |
Diferenciadores clave
- Factory-programmed A1 bus address (frente a MCP3426A2-E/SN)
- Two-channel differential measurement in a compact package (frente a MCP3426A7-E/SN)
- Integrated precision reference reduces external circuitry (frente a MCP3426A4-E/SN)
Notas de diseño
Route VIN0+, VIN0−, VIN1+, and VIN1− as short, quiet analog nets, and place their input filters close to the corresponding converter pins. Keep the I2C SCL and SDA routes away from high-impedance sensor nodes. A continuous ground plane beneath the analog section improves return-path control, but avoid routing digital return currents through the area directly beneath the differential inputs.
Do not select an MCP3426 A-series alternative solely from the package drawing. The converter family shares the 8-pin SOIC footprint while changing the factory-programmed I2C address from 0x48 for A1 through 0x4E for A7. Verify the address in firmware and confirm that no external address configuration is required before using another A-series device in an existing MCP3426A1-E/SN design.
Use the differential inputs for their intended common-mode rejection rather than applying a large signal only to one input unless the single-ended configuration is explicitly supported and correctly programmed. Establish the required input-filter corner frequency from the 15 sample/s conversion rate and the highest signal frequency of interest. Check settling behavior and reject channels through the conversion sequence described in the manufacturer datasheet.
Información de cumplimiento
A product listing references RoHS, but the manufacturer page and datasheet excerpt do not explicitly state the applicable compliance status. Verify RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations for the exact order code during qualification.