Microchip Technology

MCP3426A1-E/SN - 16-Bit Dual-Channel ADC | Microchip

料号: MCP3426A1-E/SN ✓ 量产中
2.048 V Vdss 8-pin SOIC, 0.154 in (3.90 mm) wide Package
最小起订量: 1 |

MCP3426A1-E/SN 概述

Microchip Technology MCP3426A1-E/SN is a two-channel, 16-bit delta-sigma analog-to-digital converter with differential inputs, an operating supply range of 2.7 V to 5.5 V, a conversion rate of 15 samples per second, and an 8-pin SOIC package. Its integrated precision reference is 2.048 V, supporting a differential input range of ±2.048 V.

A delta-sigma analog-to-digital converter is an ADC category that uses delta-sigma modulation and digital filtering to convert analog voltage into high-resolution digital codes. The MCP3426 belongs to the ADC → delta-sigma ADC → data-converter IC hierarchy. It is designed for precision measurement systems where differential inputs, low noise, accurate conversion, and a simple I2C interface are more important than very high sampling speed.

Key features include two differential analog input channels, resolution of up to 16 bits, and a 15 Hz conversion rate. The integrated 2.048 V reference removes the need for an external reference source, while the differential inputs help reject common-mode noise when sensing small signals. The device operates from 2.7 V to 5.5 V and communicates through I2C, making it suitable for embedded measurement systems with a microcontroller or sensor hub.

The MCP3426 family combines a low-noise, high-accuracy delta-sigma conversion stage with an internal precision reference and programmable conversion and gain behavior. The A1 device variant uses a factory-programmed I2C address, allowing deterministic bus addressing without external address straps. Differential input architecture also supports ratiometric or referenced sensor measurements when both input nodes are driven from the same excitation source.

Typical uses include industrial process measurement, battery-powered environmental sensing, strain-gauge instrumentation, pressure-sensor interfaces, and low-speed data acquisition. Its 15 Hz conversion rate is well suited to slowly changing physical variables rather than waveform capture or high-bandwidth communications. The two channels can also be configured for single-ended operation when the application does not require a fully differential signal path.

For PCB design, keep analog input traces short and place the input bypass components close to their associated pins. Provide clean return paths beneath the analog section and isolate the I2C routing from sensitive input nodes. The ADC must also be evaluated for gain, common-mode range, input filtering, reference accuracy, and system noise before the conversion output is interpreted as a precision measurement.

直接替换替代料: MCP3426A1-E/SN ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: MCP3426A1-E/SN (相同外形与封装尺寸) ——差异在于 Package, Operating Temperature Range, ADC Type, Differential Input Range, Number of Input Channels.

Microchip Technology
Package: 8-pin SOIC
Operating Temperature Range: -40 degrees C to +125 degrees C
Differential Input Range: -2.048 V to +2.048 V
Microchip Technology
Package: 8-pin SOIC, 3.90 mm body width
Operating Temperature Range: -40°C to +125°C
Differential Input Range: ±2.048 V
Microchip Technology
Package: 8-pin SOIC
Operating Temperature Range: -40 °C to +125 °C
ADC Type: Sigma-delta
Microchip Technology
Package: 8-SOIC, 3.90 mm width
Operating Temperature Range: -40 °C to +125 °C
ADC Type: Sigma-delta ADC
Microchip Technology
Package: 8-pin SOIC, 3.90 mm width
Operating Temperature Range: -55 °C to +125 °C
ADC Type: 16-bit delta-sigma ADC

MCP3426A2-E/SN

✅ 直接替换 ⚠️ 规格未核验
Microchip Technology
📦 8-pin SOIC
Up to 16 bits · 2 channels · Differential inputs · 16-bit delta-sigma ADC · 15 SPS · 2.048 V · ±2.048 V · 2.7 V to 5.5 V

联系询价

查看数据手册 →

MCP3426A3-E/SN

✅ 直接替换 ⚠️ 规格未核验
📦 8-pin SOIC
Same 8-pin SOIC converter and electrical architecture, but the factory-programmed I2C address changes from 0x48 to 0x4A; host firmware must use 0x4A.

📋 参考替代料(不在目录中)

MCP3426A4-E/SN

✅ 直接替换 ⚠️ 规格未核验
Microchip Technology
📦 8-pin SOIC
Sigma-delta · 16 bit · 2 channels · 240 samples/s · 15 samples/s · 2.048 V · ±2.048 V · 2.7 V to 5.5 V

联系询价

查看数据手册 →

MCP3426A5-E/SN

✅ 直接替换 ⚠️ 规格未核验
Microchip Technology
📦 8-pin SOIC
Sigma-delta ADC · 16 bit · 2 channels · 1 ADC · Differential · 15 SPS · 2.048 V · ±2.048 V

联系询价

查看数据手册 →

MCP3426A6-E/SN

✅ 直接替换 ⚠️ 规格未核验
📦 8-pin SOIC
Same 8-pin SOIC converter and electrical architecture, but the factory-programmed I2C address changes from 0x48 to 0x4D; host firmware must use 0x4D.

📋 参考替代料(不在目录中)

MCP3426A7-E/SN

✅ 直接替换
Microchip Technology
📦 8-pin SOIC
16-bit delta-sigma ADC · 2 analog input channels · 1 sigma-delta conversion channel · 15 samples/s · Up to 16 bits · Differential · 2.048 V · ±2.048 V

联系询价

查看数据手册 →

MCP3426A1-E/SN 最大额定值与电气特性

ADC Type Delta-sigma ADC
分辨率 Up to 16 bits
Number of Input Channels 2
Input Type Differential
Conversion Rate 15 samples/s
Internal Reference Voltage 2.048 V
Differential Input Range ±2.048 V differential
Supply Voltage Range 2.7 V to 5.5 V
接口 I2C
封装 8-pin SOIC, 0.154 in (3.90 mm) wide
安装类型 Surface mount
Noise Performance Low noise
Conversion Accuracy High accuracy
I2C Address 0x48 factory-programmed for MCP3426A1
RoHS 状态 Unknown
REACH Status Unknown

MCP3426A1-E/SN 引脚配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
引脚 1 SCL — I2C clock input
引脚 2 SDA — I2C data input and output
引脚 3 VREF — Reference voltage input or internal reference connection
引脚 4 VDD — Positive supply voltage
引脚 5 VIN0+ — Channel 0 non-inverting analog input
引脚 6 VIN0- — Channel 0 inverting analog input
引脚 7 VIN1- — Channel 1 inverting analog input
引脚 8 VIN1+ — Channel 1 non-inverting analog input

典型应用

MCP3426A1-E/SN 适用于 6 应用s: Industrial Pressure Sensor Interface, Strain Gauge Instrumentation, Environmental Monitoring, Battery-Powered Sensor Node, Precision Process Monitoring, Portable Measurement Instrument.

🏭

Industrial Pressure Sensor Interface

The MCP3426A1-E/SN suits low-speed bridge or ratiometric pressure-sensor measurements because it accepts two differential input channels, provides up to 16-bit resolution, and operates at 15 sample/s. Connect the sensor excitation and bridge output so common sensor noise and supply variation are rejected. The internal 2.048 V reference supports a ±2.048 V differential range, while the 2.7 V to 5.5 V supply range accommodates common industrial rails. An input RC filter can suppress high-frequency interference, and the converter's I2C output allows the host controller to read settled measurements without continuously clocking a high-rate converter.

📐

Strain Gauge Instrumentation

MCP3426A1-E/SN can digitize millivolt-level strain-gauge changes when both differential inputs remain within the supported common-mode range and the bridge output is suitably conditioned. Its differential conversion architecture rejects equal-magnitude noise on the two input nodes, while the low-noise 16-bit delta-sigma core supports precise static-force or slow-deformation measurements. The 15 sample/s rate is appropriate for load cells, force sensing, and structural monitoring. Use a low-noise bridge excitation, matched input filtering, and a solid ground strategy to preserve the small differential signal before conversion.

🧩

Environmental Monitoring

The MCP3426A1-E/SN is appropriate for slowly varying environmental signals such as temperature, humidity, gas concentration, and light levels when the sensor output is compatible with the ±2.048 V differential range. Its 15 sample/s rate provides more than enough throughput for periodic environmental readings, while up-to-16-bit resolution can retain useful detail in slowly changing signals. The internal 2.048 V reference reduces external reference complexity, and the two differential channels allow paired sensing or sensor-plus-reference measurements. The host can read through I2C and apply calibration or compensation in firmware.

🔋

Battery-Powered Sensor Node

MCP3426A1-E/SN fits low-duty-cycle battery-powered sensor nodes because it supports a 2.7 V to 5.5 V supply range and is designed for low-noise precision conversion rather than high-rate sampling. The host controller can keep the sensor powered, start a conversion, wait for the 15 sample/s measurement cadence, and transmit the processed value. Differential inputs help reject noise shared by both sensor lines. Because the converter is not intended for waveform acquisition, power-management decisions should focus on sensor duty cycle, board leakage, reference settling, and the number of channels that must remain active.

🌐

Precision Process Monitoring

MCP3426A1-E/SN can serve as the measurement ADC in a process-control front end for slow pressure, flow, level, or chemical signals. Differential conversion is valuable when a transmitter outputs a small signal relative to its supply or common-mode voltage, and the 2.048 V internal reference provides a defined conversion basis. Two channels support sequential acquisition, while the 15 sample/s rate suits process variables that evolve more slowly than industrial communication cycles. Firmware can perform gain, offset, and temperature compensation before transmitting the corrected engineering value to supervisory control equipment.

🖥️

Portable Measurement Instrument

MCP3426A1-E/SN is useful in portable laboratory and field instruments that measure low-level analog quantities with limited board area. The 8-pin SOIC package simplifies assembly, the internal reference limits external components, and the I2C interface allows economical connection to a display controller or embedded processor. Its two differential channels can acquire a measurement and a reference or support two related sensor inputs. The 15 sample/s conversion rate aligns with stable handheld readings, while the up-to-16-bit resolution and differential architecture help preserve accuracy in systems where sensor leads and ground offsets can degrade low-level measurements.

推荐产品汇总

MCP3426A1-E/SN Microchip Technology 用于: Industrial Pressure Sensor Interface, Strain Gauge Instrumentation, Environmental Monitoring, Battery-Powered Sensor Node, Precision Process Monitoring, Portable Measurement Instrument MCP3426A2-E/SN Microchip Technology 用于: Industrial Pressure Sensor Interface MCP3427 Address-configurable family alternative 用于: Industrial Pressure Sensor Interface, Environmental Monitoring, Precision Process Monitoring MCP3426A3-E/SN Same-family converter for address planning 用于: Strain Gauge Instrumentation MCP3428 Address-configurable family alternative 用于: Strain Gauge Instrumentation, Battery-Powered Sensor Node, Portable Measurement Instrument MCP3426A4-E/SN Microchip Technology 用于: Environmental Monitoring MCP3426A5-E/SN Microchip Technology 用于: Battery-Powered Sensor Node MCP3426A6-E/SN Same-family converter with alternate address 用于: Precision Process Monitoring MCP3426A7-E/SN Microchip Technology 用于: Portable Measurement Instrument
What are the key specifications of MCP3426A1-E/SN that engineers should know?
The MCP3426A1-E/SN is a two-channel, 16-bit delta-sigma ADC with differential inputs, a 2.048 V internal reference, a 15 sample/s conversion rate, and an I2C interface. According to the Microchip MCP3426/7/8 datasheet, its differential input range is ±2.048 V and its operating supply range is 2.7 V to 5.5 V. It is packaged in an 8-pin SOIC, making it appropriate for low-speed precision measurement rather than high-frequency signal acquisition.
What is the operating voltage of MCP3426A1-E/SN?
The MCP3426A1-E/SN operates from 2.7 V to 5.5 V, as stated in the Microchip MCP3426 product information and MCP3426/7/8 datasheet. This range supports common embedded and industrial supply rails while allowing the same converter design to operate from a regulated 3.3 V or 5 V source. Designers should still verify the input common-mode range, output code range, and application-specific gain configuration against the datasheet before applying signals.
Where can I download the MCP3426A1-E/SN datasheet PDF?
The MCP3426A1-E/SN datasheet is available from Microchip Technology at https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/DataSheets/22226a.pdf. The document covers the MCP3426, MCP3427, and MCP3428 family and includes the converter architecture, electrical characteristics, I2C operation, address selection, and application information. Use the MCP3426 sections when configuring the A1 factory-address variant.
Where can I find the MCP3426A1-E/SN pinout?
The MCP3426A1-E/SN pinout is published in the pin-description and connection diagrams of the Microchip MCP3426/7/8 datasheet. The 8-pin SOIC uses pins for SCL, SDA, VREF, VDD, the two differential input channels, and ground. Assign PCB tracks by using the exact package drawing and pin-description table in the manufacturer datasheet, especially because the family also includes address-configuration options that must not be confused with the A1 variant.
How does MCP3426A1-E/SN differ from MCP3427 and MCP3428?
The MCP3426A1-E/SN, MCP3427, and MCP3428 share the low-noise 16-bit delta-sigma converter concept, but their I2C addressing options differ. The MCP3426A1 has a factory-programmed address, while MCP3427 and MCP3428 provide address selection through address pins according to the Microchip family datasheet. Those address differences affect firmware configuration and should be checked before treating one family member as a functional substitute for another.
MCP3426A1-E/SN vs MCP3426A2-E/SN - which is better for an I2C sensor bus?
Choose MCP3426A1-E/SN when firmware expects the A1 factory-programmed I2C address, and choose MCP3426A2-E/SN when the bus design expects the corresponding A2 address. Both belong to the same MCP3426 family and use the same 8-pin SOIC and 16-bit conversion architecture. The important selection criterion is the programmed address: changing converter variant can require a corresponding change to the host's I2C address register.
When should I choose MCP3426A1-E/SN over another MCP3426 address variant?
Choose MCP3426A1-E/SN when a fixed factory-programmed address is compatible with the existing I2C topology and the application prioritizes a simple, deterministic connection. The A1 device retains the family's two differential channels, up-to-16-bit resolution, 2.048 V reference, and 15 sample/s conversion rate. Select another address variant only when bus addressing requires it, and verify the associated address value and firmware configuration before release to production.
Is MCP3426A1-E/SN suitable for low-speed sensor measurement?
Yes, MCP3426A1-E/SN is well suited to low-speed sensor measurement because it provides two differential inputs, up to 16-bit resolution, and a 15 sample/s conversion rate. Differential excitation and acquisition can reduce common-mode noise for strain, pressure, temperature, and chemical-sensor interfaces. It is not appropriate for high-bandwidth waveform capture, where a much faster ADC and corresponding signal-chain bandwidth would be required.
What is the best drop-in replacement for MCP3426A1-E/SN?
The closest same-package replacement is an MCP3426A-family device with the same 8-pin SOIC footprint and converter functions, but the factory-programmed I2C address must match the original A1 device for uninterrupted firmware operation. The MCP3426A2-E/SN, A3, A4, A5, A6, and A7 devices are physically related family options, although their addresses differ. Confirm address, gain configuration, supply range, and timing in the manufacturer datasheet before substitution.
Can MCP3426A1T-E/SN replace MCP3426A1-E/SN?
MCP3426A1T-E/SN has the same MCP3426A1 electrical identity but a different reel or tape orientation suffix, so it can serve as the same functional device when its orientation matches the assembly process. It is not a distinct functional upgrade, and an unverified tape orientation can create assembly errors. Use the manufacturer ordering information to confirm the pin-one orientation, reel packaging, and shipping details rather than treating it as a different converter design.
What is the best cross-brand equivalent for MCP3426A1-E/SN?
No cross-brand equivalent is established here as a guaranteed drop-in replacement for MCP3426A1-E/SN. A valid substitute must provide the same 8-pin SOIC footprint, pin-compatible I2C and analog connections, compatible 2.7 V to 5.5 V supply operation, and equivalent conversion behavior. Use a parametric cross-reference tool to identify candidates, then compare the electrical tables and address handling; functional similarity alone does not establish drop-in compatibility.
Where can I buy MCP3426A1-E/SN and check its current lead time?
Use the Request a Quote form on this page to ask for MCP3426A1-E/SN availability, current lead time, minimum order quantity, and volume pricing. Quote-based sourcing confirms the exact suffix and packaging required by your assembly process. The component's standard ordering designation is MCP3426A1-E/SN, and the manufacturer offers the related MCP3426 family in an 8-pin SOIC configuration.
What is the price of MCP3426A1-E/SN?
The current MCP3426A1-E/SN price should be requested through the Request a Quote form on this page because commercial pricing can vary with quantity, inventory, and delivery requirements. Provide the required order quantity, date code preference, and packaging details in the request. This approach returns a current quotation for the exact MCP3426A1-E/SN order code rather than a price attached to a different suffix or package.
Is MCP3426A1-E/SN in stock?
Current stock for MCP3426A1-E/SN should be confirmed through the Request a Quote form on this page. Submit the required quantity and delivery schedule so the response reflects the exact device suffix and any date-code constraints. For production planning, also account for standard distributor lead times and the time required for incoming inspection, PCB assembly, and any lot-specific qualification.
What are the main design considerations for MCP3426A1-E/SN?
The main design considerations are input common-mode range, gain configuration, filtering, reference behavior, I2C address compatibility, and analog grounding. The MCP3426A1-E/SN converts at 15 sample/s, so an analog low-pass filter can often reject out-of-band noise without sacrificing intended measurement bandwidth. Place input and bypass components near the IC, keep I2C traces separate from sensitive analog nodes, and verify the conversion sequence and code interpretation in the manufacturer datasheet.

工程参考数据: MCP3426A1-E/SN ——对比、设计指导和合规信息。

选型指南

Choose MCP3426A1-E/SN when the design needs a two-channel, 16-bit delta-sigma ADC with differential inputs, an internal 2.048 V reference, 15 sample/s conversion, and I2C address 0x48. It is appropriate for pressure, strain, environmental, and general low-speed process measurements. Choose MCP3426A2-E/SN through MCP3426A7-E/SN when the same converter and 8-pin SOIC footprint are needed but the I2C bus requires another factory-programmed address. Treat those variants as pin-compatible alternatives that require corresponding firmware address changes. MCP3427 and MCP3428 provide address selection through address pins and are better considered family alternatives when configurable addressing is required rather than direct replacements for a fixed-address A1 design. No cross-brand part is presented as a guaranteed drop-in substitute because equivalent pinout, input range, gain behavior, reference implementation, timing, and I2C address must all be verified.

与替代料对比

参数 本产品 MCP3426A2-E/SN MCP3426A3-E/SN MCP3426A4-E/SN MCP3426A5-E/SN MCP3426A6-E/SN MCP3426A7-E/SN
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Resolution Up to 16 bits Up to 16 bits Up to 16 bits Up to 16 bits Up to 16 bits Up to 16 bits Up to 16 bits
Number of Channels 2 2 2 2 2 2 2
Conversion Rate 15 samples/s 15 samples/s 15 samples/s 15 samples/s 15 samples/s 15 samples/s 15 samples/s
Internal Reference 2.048 V 2.048 V 2.048 V 2.048 V 2.048 V 2.048 V 2.048 V
Differential Input Range ±2.048 V ±2.048 V ±2.048 V ±2.048 V ±2.048 V ±2.048 V ±2.048 V
Supply Voltage Range 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V
Factory-Programmed I2C Address 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E

关键差异点

  • Factory-programmed A1 bus address (对比 MCP3426A2-E/SN)
  • Two-channel differential measurement in a compact package (对比 MCP3426A7-E/SN)
  • Integrated precision reference reduces external circuitry (对比 MCP3426A4-E/SN)

设计说明

Route VIN0+, VIN0−, VIN1+, and VIN1− as short, quiet analog nets, and place their input filters close to the corresponding converter pins. Keep the I2C SCL and SDA routes away from high-impedance sensor nodes. A continuous ground plane beneath the analog section improves return-path control, but avoid routing digital return currents through the area directly beneath the differential inputs.

Do not select an MCP3426 A-series alternative solely from the package drawing. The converter family shares the 8-pin SOIC footprint while changing the factory-programmed I2C address from 0x48 for A1 through 0x4E for A7. Verify the address in firmware and confirm that no external address configuration is required before using another A-series device in an existing MCP3426A1-E/SN design.

Use the differential inputs for their intended common-mode rejection rather than applying a large signal only to one input unless the single-ended configuration is explicitly supported and correctly programmed. Establish the required input-filter corner frequency from the 15 sample/s conversion rate and the highest signal frequency of interest. Check settling behavior and reject channels through the conversion sequence described in the manufacturer datasheet.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

A product listing references RoHS, but the manufacturer page and datasheet excerpt do not explicitly state the applicable compliance status. Verify RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations for the exact order code during qualification.

相关搜索

MCP3426A1-E/SN datasheet MCP3426A1-E/SN pinout MCP3426A1-E/SN datasheet pdf MCP3426A1-E/SN equivalent MCP3426A1-E/SN replacement MCP3426A1-E/SN cross reference MCP3426A1-E/SN vs MCP3426A2-E/SN MCP3426A1-E/SN price MCP3426A1-E/SN stock Microchip MCP3426A1-E/SN MCP3426A1-E/SN 8-SOIC pinout MCP3426 16-bit delta-sigma ADC

相关元器件 & 术语

Microchip Technology MCP3426A1-E/SN MCP3426A2-E/SN MCP3426A3-E/SN MCP3426A4-E/SN MCP3426A5-E/SN MCP3426A6-E/SN MCP3426A7-E/SN MCP3427 MCP3428 ADC delta-sigma ADC data converter IC analog-to-digital converter differential input precision reference I2C 16-bit resolution 15 samples per second 2.048 V reference 8-pin SOIC SOIC family surface-mount package industrial process measurement strain-gauge instrumentation
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情