MX30LF1G18AC-XKR-T - 1Gb SLC NAND Flash, 3V, BGA-63 | Macronix
N.º de pieza: MX30LF1G18AC-XKR-T ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $3.42 | $3,42 |
| 10 | $2.99 | $29,90 |
| 100 | $2.45 | $245,00 |
| 500 | $2.1 | $1.050,00 |
| 1.000 | $1.84 | $1.840,00 |
| 3.000 | $1.62 | $4.860,00 |
MX30LF1G18AC-XKR-T Descripción general
What is SLC NAND Flash? SLC (Single-Level Cell) NAND is a non-volatile memory technology that stores one bit per cell, giving it the highest endurance (typically 100k P/E cycles per block), the lowest bit-error rate, and the fastest write speeds of any NAND family. Within the broader hierarchy, SLC NAND sits below DRAM in the memory pyramid: faster than NOR for large-block writes, denser and cheaper per bit than NOR, and far more reliable than MLC/TLC/QLC NAND at the cost of lower density per die. The MX30LF1G18AC-XKR-T therefore fills the niche where designers need MLC-class capacity but cannot tolerate MLC-level endurance or error-rate penalties.
Key differentiating features include ONFI 1.0 command-set compliance, a hardware PT (Protection) pin on ball G5 that block-protects the entire chip at power-on, internal 4-bit ECC engines, and an extended -40 C to +105 C automotive temperature range. The 63-ball VFBGA package keeps board area under 100 mm^2, while the asynchronous interface allows simple MCU/FPGA glue logic without requiring an ONFI controller IP block.
Architecturally, the MX30LF1G18AC implements a single 1 Gbit die organized as 1024 blocks, each containing 64 pages of 2112 bytes (2048 data + 64 spare). Read is page-granular (typically 25 us), program is page-driven (~300 us), and erase is block-level (typically 2 ms). The ONFI 1.0 command set ensures the part can be driven by any standard NAND controller, including Linux MTD drivers and bare-metal bootloaders.
Typical applications include automotive infotainment and instrument-cluster boot/data storage, industrial HMI panel firmware, point-of-sale terminals, IoT gateways requiring reliable OTA update storage, and medical devices where long-term data retention (10-year JEDEC spec) outweighs density requirements.
When designing with this device, route the BGA balls to a minimum 4-layer PCB with continuous GND plane under the package to maintain signal integrity on the 8-bit parallel bus, and budget the I/O capacitance (typically 10 pF) when calculating read-window margins. Always issue the PT-protection release command sequence before programming in production, or leave PT floating (the internal weak pull-down disables protection).
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Alternativas directas para MX30LF1G18AC-XKR-T — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
MX30LF1G18AC-XKI
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MX30LF2G18AC-XKR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MX30LF1G08AA-XKI
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MX30LF1G18AC-XKR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MX30LF1G18AC-XKR-T Valores máximos y características eléctricas
| Tipo de memoria | Non-volatile NAND Flash (Single-Level Cell) |
| Density | 1 Gbit (128 MB) |
| Organización de memoria | 128M x 8 |
| Supply Voltage (VCC) | 2.7 V to 3.6 V |
| Interfaz | Parallel asynchronous 8-bit (x8) |
| Read Access Time (tRC) | 20 ns |
| Page Size | 2112 bytes (2048 + 64 spare) |
| Block Size | 64 pages (128 KB + 4 KB spare) |
| Block Count | 1024 blocks |
| ECC Support | Internal 4-bit ECC |
| Command Set | ONFI 1.0 compliant |
| Protection Pin (PT) | Active-high at power-on, internal weak pull-down |
| Encapsulado | 63-ball VFBGA, 9 x 11 mm |
| Temperatura de funcionamiento | -40 C to +105 C (automotive grade) |
| Data Retention | 10 years (per JEDEC JESD22-A117) |
| Endurance | 100k program/erase cycles per block (SLC) |
| Tipo de montaje | Surface Mount |
| Estado RoHS | Compliant |
Guía de configuración de pines de MX30LF1G18AC-XKR-T 63-ball vfbga, 9 x 11 mm
Configuración de pines para MX30LF1G18AC-XKR-T (encapsulado 63-ball vfbga, 9 x 11 mm). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para MX30LF1G18AC-XKR-T.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MX30LF1G18AC-XKR-T es adecuado para 6 aplicacións: Automotive Infotainment Boot & Data Storage, Industrial HMI Panel Firmware Storage, Point-of-Sale (POS) Terminal Transaction Logging, IoT Gateway OTA Update Storage, Medical Device Patient Data Logging, Networking Equipment Routing Table & Log Storage.
Automotive Infotainment Boot & Data Storage
The MX30LF1G18AC-XKR-T's 1 Gbit SLC density, automotive +105 C grade, and 100 k P/E cycle endurance make it a strong fit for automotive infotainment head units and instrument clusters where the host SoC boots from NAND and stores navigation maps, audio buffers, and diagnostic logs. Placed on a 4-layer PCB with continuous GND plane beneath the BGA, it pairs with an ONFI-capable application processor; the 4-bit internal ECC corrects single-bit errors that occur naturally across the -40 C to +105 C automotive temperature span, eliminating the need for an external ECC engine. The PT pin (ball G5) can be tied to a power-good rail to protect boot blocks during in-vehicle brown-out events.
Recomendado
Industrial HMI Panel Firmware Storage
Factory-floor human-machine interface (HMI) panels require long-retention, high-endurance code storage that survives 10+ years of continuous operation. The MX30LF1G18AC-XKR-T's 10-year data retention and 100 k P/E cycle rating align with industrial panel MTBF targets, while the parallel 8-bit interface allows simple FPGA or MCU control without an external NAND controller IP block. Designers place the BGA on a 4-layer board, route the 8-bit data bus with 50 ohm controlled impedance, and rely on the ONFI 1.0 command set for predictable timing during firmware update operations. The +105 C ambient rating covers sealed enclosure environments without active cooling.
Recomendado
Point-of-Sale (POS) Terminal Transaction Logging
POS terminals log thousands of transactions per day to non-volatile storage and require bit-error-failure tolerant code and data storage. The MX30LF1G18AC-XKR-T's SLC architecture delivers 10-100x higher endurance than MLC/TLC NAND at the same density, while the parallel interface allows transaction bursts to be written at ~3.3 MB/s (8-bit bus at 20 ns cycle). ECC scrubbing every 10k P/E cycles extends retention; the PT pin protects boot sectors against accidental field-erasure. The BGA-63 footprint keeps the BOM cost below NOR-Flash alternatives of equivalent density.
Recomendado
IoT Gateway OTA Update Storage
IoT gateways in smart-building and asset-tracking deployments require reliable over-the-air (OTA) firmware update storage with predictable fail-safe recovery. The MX30LF1G18AC-XKR-T stores dual A/B firmware images in two partition blocks; on a failed boot, the host reverts to the previous image via ONFI block-copy operations. The 1 Gbit capacity covers 2-3 firmware revisions plus 256 MB of telemetry log buffer. The BGA-63 package fits inside compact gateway enclosures with limited PCB area, and the 2.7-3.6 V supply aligns with battery-backed 3.3 V rail designs without needing a level shifter.
Recomendado
Medical Device Patient Data Logging
Patient-monitoring devices such as infusion pumps and portable ECG recorders must store days to weeks of patient data in non-volatile memory with bit-error-failure-safe reliability. The MX30LF1G18AC-XKR-T's 10-year data retention and 100 k P/E endurance cover the typical 5-7 year medical-device service life with margin. Its parallel 8-bit interface allows simple read/write DMA from medical MCUs without needing a complex file system layer. The automotive +105 C rating exceeds medical operating-temperature requirements, ensuring reliability in autoclave-adjacent hospital environments.
Recomendado
Networking Equipment Routing Table & Log Storage
Industrial routers and managed switches need high-endurance non-volatile storage for routing tables, configuration logs, and firmware images. The MX30LF1G18AC-XKR-T's ONFI 1.0 command set enables Linux MTD driver support for open-source routing stacks, while its SLC endurance handles the frequent log-write workload of managed switches. The parallel interface allows direct memory-mapped access from network processors, achieving higher throughput than SPI NOR at the same density. The PT pin protects against accidental in-field erase during power-sequencing anomalies on PoE-powered switches.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MX30LF1G18AC-XKR-T — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MX30LF1G18AC-XKI | MX30LF2G18AC-XKR | MX30LF1G08AA-XKI | |
|---|---|---|---|---|---|
| Brand | Macronix | Macronix | Macronix | Macronix | |
| Package | 63-VFBGA (9x11 mm) | 63-VFBGA (9x11 mm) - same | 63-VFBGA (9x11 mm) - same | 63-VFBGA (9x11 mm) - same | 48-TSOP - different footprint |
| Density | 1 Gbit (128 MB) | 1 Gbit | 2 Gbit | 1 Gbit | 1 Gbit |
| Cell Type | SLC | SLC | SLC | SLC | SLC |
| Interface | Parallel 8-bit, ONFI 1.0 | Parallel 8-bit, ONFI 1.0 | Parallel 8-bit, ONFI 1.0 | Parallel 8-bit, ONFI 1.0 | Parallel 8-bit, ONFI 1.0 |
| Operating Voltage | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V |
| Operating Temperature | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +85 C | -40 C to +85 C |
| PT (Protection) Pin | Yes (ball G5) | Yes (ball G5) | Yes (ball G5) | No (first-generation die) | Yes |
| Endurance (P/E cycles) | 100,000 | 100,000 | 100,000 | 100,000 | 100,000 |
| Delivery Format | Tape & Reel | Tray | Tape & Reel | Tray | Tape & Reel |
Diferenciadores clave
- Higher automotive temperature rating than first-generation sibling (frente a MX30LF1G08AA-XKI)
- Includes hardware PT (Protection) pin absent in prior generation (frente a MX30LF1G08AA-XKI)
- BGA-63 footprint compatible with 2 Gbit upgrade path (frente a MX30LF2G18AC-XKR)
- Tape-and-reel packaging for high-volume SMT assembly (frente a MX30LF1G18AC-XKI)
Notas de diseño
Route the 8-bit parallel data bus (DQ0-DQ7), control signals (CLE, ALE, CE, RE, WE), and R/B on a 4-layer PCB with continuous GND plane beneath the BGA-63 footprint. Maintain 50 ohm controlled impedance on the data bus and group DQ0-DQ7 within 0.5 mm of each other to minimize skew. Place 100 nF decoupling caps within 0.005 inches of each VCC ball. Avoid routing any signal traces beneath the BGA package.
Always issue the PT-protection release command sequence before programming the device in production, or leave the PT pin (ball G5) floating to use the internal weak pull-down. Driving PT high at power-on permanently block-protects the entire chip and requires a hardware reset to recover. Do not use the PT pin as a GPIO - it has no other function and its state is sampled only at VCC power-on.
The MX30LF1G18AC has a typical I/O capacitance of 10 pF per pin. When calculating read-window margins on a heavily-loaded bus (>4 devices), include this capacitance in your worst-case rise/fall time calculation. For read cycles, add 1 ns of propagation delay per 100 mils of trace beyond the first inch to avoid tRC violations at 20 ns.
Estimated: at continuous read operation (8-bit bus at 20 ns cycle) on a 4-layer PCB with 1 oz copper, the MX30LF1G18AC dissipates approximately 80 mW (input values: VCC = 3.3 V, ICC_active = 24 mA). The BGA-63 package has a typical theta_JA of 50 C/W, resulting in a 4 C junction temperature rise - well within the 105 C ambient limit. No heatsink is required.
Información de cumplimiento
XK suffix indicates automotive temperature grade; AEC-Q100 qualification per Macronix product page. Halogen-free and RoHS compliant per Macronix material declaration.
