TPS536C9TRSLR - 12-Phase TLVR Buck Controller, 765A | TI
N.º de pieza: TPS536C9TRSLR ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
TPS536C9TRSLR Descripción general
A multiphase buck controller is a power-management IC that orchestrates multiple power stages in parallel to deliver high current at low voltage, dividing current among phases for reduced ripple, better thermal distribution, and fast transient response. The TPS536C9T sits within the hierarchy of switching regulators as a controller-class device, pairing with external TI NexFET smart power stages to form a complete voltage regulator solution (VR) for processors.
Key features include native trans-inductor voltage regulator (TLVR) topology support with LC open and short protection, VR14 SVID interface compliance, and a PMBus interface for telemetry and configuration. Built-in non-volatile memory (NVM) stores configuration, and the D-CAP+ architecture provides fast transient response, low output capacitance, and accurate dynamic current sharing across phases.
The controller is fully compatible with TI NexFET smart power stages, allowing flexible N+M phase allocation (N+M <= 12, M <= 6) between the two channels. This scalability suits both compact dual-rail designs and high-current single-rail configurations used by modern server CPUs and GPUs.
Typical applications include server CPU core power (VR14 SVID rails), ASIC and FPGA point-of-load power, AI accelerator power delivery, and networking line-card processors requiring sub-1V, multi-hundred-amp rails with PMBus manageability.
Design tip: TI recommends keeping at least 800 mil distance between controller and power stages, sharing a common ground plane, and using the PMBus/NVM configuration flow during bring-up to tune loop response before production.
This page synthesizes verified datasheet parameters, drop-in alternatives, and practical design guidance not found on the manufacturer product page.
Alternativas directas para TPS536C9TRSLR — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con TPS536C9TRSLR (mismo factor de forma y huella) — difiere en Non-Volatile Memory, Package, Topology, Control Interface, Number of Channels.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
TPS536C9RSLR
✅ Sustitución directa✓ En stock
$14.3182 / unidad
Ver hoja de datos →TPS536C9T
✅ Sustitución directa✓ En stock
$5.8 / unidad
Ver hoja de datos →TPS536C9TRSLR Valores máximos y características eléctricas
| Topología | Step-down multiphase buck controller (D-CAP+) |
| Number of Channels | 2 (N + M <= 12 phases, M <= 6) |
| Total Output Current | Up to 765 A (with 12 phases of power stages) |
| Rango de tensión de entrada | 4.5 V to 17 V |
| Rango de tensión de salida | 0.25 V to 5.5 V |
| Control Interface | VR14 SVID and PMBus |
| TLVR Support | Native trans-inductor voltage regulator topology with LC open and short protection |
| Non-Volatile Memory | Built-in NVM for configuration |
| Power Stage Compatibility | TI NexFET smart power stages |
| Temperatura de funcionamiento | -40C to +125C |
| Encapsulado | 48-pin VQFN (RSL) with exposed pad |
| Tipo de montaje | Surface Mount |
| Tipo de salida | Positive, adjustable |
| Architecture | D-CAP+ (fast transient, dynamic current sharing) |
| Marking | TPS536C9T |
Guía de configuración de pines de TPS536C9TRSLR 48-pin vqfn (rsl) with exposed pad
Configuración de pines para TPS536C9TRSLR (encapsulado 48-pin vqfn (rsl) with exposed pad). Este dispositivo de potencia presenta terminales de puerta, drenador y fuente. Para encapsulados no polarizados, consulte la hoja de datos del fabricante para conocer la orientación exacta del pin 1 y los detalles del footprint. Las aplicaciones habituales incluyen el diseño de fuentes de alimentación, el accionamiento de motores y la conmutación de cargas.
No hay datos detallados de patillaje disponibles para TPS536C9TRSLR.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
TPS536C9TRSLR es adecuado para 6 aplicacións: Server CPU Core Power (VR14), AI Accelerator Power Delivery, ASIC and FPGA Point-of-Load, Networking and Telecom Line Cards, Storage and Server Backplane Power, High-Density Multiphase Proof-of-Concept.
Server CPU Core Power (VR14)
The TPS536C9TRSLR is purpose-built for VR14 SVID-compliant CPU core rails in 1U/2U servers and motherboards. Its VR14 SVID interface lets the CPU command output voltage, offset, and active phase count in real time, while PMBus provides platform-level telemetry for current, voltage, and temperature. With N + M <= 12 phase capability and TI NexFET smart power stages, the controller sustains multi-hundred-amp core currents at sub-1V with tight dynamic regulation. D-CAP+ control keeps the loop fast enough for microsecond-class load steps, and NVM stores per-platform settings without external memory.
Recomendado
AI Accelerator Power Delivery
AI accelerators present extreme transient loads - hundreds of amps stepping in microseconds - which the TPS536C9TRSLR addresses through native TLVR support and D-CAP+ control. The TLVR topology with LC open and short protection lets designers use coupled-inductor arrays to slash output capacitance while meeting tight transient budgets on sub-1V rails. Driving up to 12 phases of TI smart power stages, the controller scales to 765A-class solutions. PMBus telemetry supports fleet-level health monitoring of accelerator cards in data-center fleets, and runtime phase shedding maintains light-load efficiency during idle inference periods.
Recomendado
ASIC and FPGA Point-of-Load
High-end ASICs and FPGAs need multiple precisely sequenced low-voltage rails, and the TPS536C9TRSLR covers this with two independently configurable channels and a 0.25V to 5.5V output range. The PMBus interface supports sequencing, margining, and fault management, while NVM retains configuration across power cycles without external EEPROM. D-CAP+ dynamic current sharing keeps rail accuracy high even during simultaneous channel load events, and the flexible N+M phase allocation (M <= 6) lets one controller serve both a large core rail and a smaller auxiliary rail, consolidating BOM and layout area on dense boards.
Recomendado
Networking and Telecom Line Cards
Line-card processors and switch ASICs in networking equipment demand sub-1V, tens-to-hundreds-of-amp rails operating reliably from -40C to +85C ambient, which the TPS536C9TRSLR's -40C to +125C rating comfortably covers. PMBus manageability enables remote monitoring and fault logging required by carrier-grade platforms, and SVID-free operation is possible when no CPU is present by configuring Reset# with a pull-up and handling unused pins as TI's E2E forum guidance describes. TLVR support benefits the aggressive transient requirements of traffic-dependent ASIC load bursts in high-port-count switches.
Recomendado
Storage and Server Backplane Power
Storage controllers and backplane-attached compute benefit from the TPS536C9TRSLR's dual-channel architecture: one channel powers a high-current SoC rail while the second serves a memory or ASIC rail from a single controller. The 4.5V to 17V input range accepts intermediate-bus voltages commonly found behind backplane DC-DC stages, and the 0.25V to 5.5V output range covers both modern sub-1V cores and legacy 5.5V logic. PMBus telemetry simplifies chassis-level manageability, while TLVR-equipped designs cut output capacitor count, valuable in space-constrained drive electronics.
Recomendado
High-Density Multiphase Proof-of-Concept
For system bring-up and reference-design evaluation, the TPS536C9TRSLR's NVM plus PMBus configuration flow lets engineers tune loop response, phase allocation, and protection thresholds without hardware respins. TI's E2E layout guidance - at least 800 mil spacing between controller and power stages, common ground plane, and careful PWMx routing - applies directly to evaluation boards. The flexible N+M <= 12 phase allocation enables quick comparison of 8+4 versus 10+2 rail strategies on the same PCB, making the controller an efficient platform for characterizing NexFET power-stage pairings.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para TPS536C9TRSLR — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | TPS536C9RSLR | TPS536C9T |
|---|---|---|---|
| Package | 48-VQFN (RSL) exposed pad | 48-VQFN (RSL) - same | 48-VQFN (RSL) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Input Voltage Range | 4.5 V to 17 V | 4.5 V to 17 V | 4.5 V to 17 V |
| Output Voltage Range | 0.25 V to 5.5 V | 0.25 V to 5.5 V | 0.25 V to 5.5 V |
| Phase Configuration | N + M <= 12, M <= 6, dual channel | N + M <= 12, M <= 6, dual channel | N + M <= 12, M <= 6, dual channel |
| Interfaces | VR14 SVID + PMBus | VR14 SVID + PMBus | VR14 SVID + PMBus |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C |
Diferenciadores clave
- Native TLVR topology support (frente a TPS536C9RSLR)
- 12-phase dual-channel scalability (frente a TPS536C9RSLR)
- VR14 SVID + PMBus with built-in NVM (frente a TPS536C9RSLR)
Notas de diseño
Per TI E2E application guidance, keep at least 800 mil distance between the TPS536C9T controller and all power stages, place the controller and power stages on a common ground plane, and route PWMx signals short and away from high-dv/dt switch nodes. This isolates sensitive current-sense, SVID, and PMBus lines from gate-drive noise, which otherwise shows up as current-sharing error and telemetry jitter on 12-phase designs.
If one channel is unused (e.g., all 12 phases on a single rail), do not leave the channel pins floating: per TI E2E forum guidance, connect Reset# to a pull-up resistor and map the unused temperature-sense pin to the active rail's sensor or a defined level. Floating sense inputs can cause spurious fault flags at boot. Validate the NVM configuration over PMBus before committing production firmware.
Estimated: with 12 phases at 765A total, each phase carries roughly 64A; thermal design effort concentrates in the NexFET power stages and inductors rather than the controller itself. Use the exposed pad of the 48-VQFN (RSL) tied to a solid ground plane with multiple thermal vias to keep the controller junction well inside the -40C to +125C rating, and budget power-stage copper pours separately.
Información de cumplimiento
Compliance data not present in the provided web data; consult the TI product page quality section for RoHS/REACH certificates.
