ADC08D500CIYB - Dual 8-Bit 500MSPS ADC | Texas Instruments
MPN: ADC08D500CIYB ⚠ آخرین فرصت خریدADC08D500CIYB نمای کلی
An analog-to-digital converter is an integrated circuit that samples continuous-time analog waveforms into the binary, register-blocked digital domain at a fixed sampling rate; the ADC08D500 family specifically targets the high-speed, low-power segment used in communications, test equipment, and radar signal chains. The product type hierarchy is ADC > data converter > mixed-signal IC > semiconductor. The ADC08D500 family is also commonly referred to as a flash ADC with folding and interpolating architecture, a two-step sub-ranging ADC, or a high-speed pipeline ADC derivative.
Key features include internal sample-and-hold, choice of SDR or DDR output clocking, an interleave mode that doubles sampling rate, multiple ADC synchronization capability, guaranteed no missing codes, a serial interface for extended control, fine adjustment of input full-scale range and offset, and duty-cycle corrected sample clock. These capabilities make the device a preferred option for dual-channel wideband digital oscilloscopes and direct RF downconversion chains.
The device uses a folding and interpolating architecture with an internal calibration engine, achieving low-latency digital conversion without the deep pipeline delay seen in pipelined ADCs. This makes it well suited for time-domain applications such as radar pulse measurement and triggering applications where deterministic latency matters more than raw SNR.
Typical applications include radar and LIDAR digitizer front-ends, automated test equipment, digital oscilloscopes, communications basestation receivers, and high-speed signal analyzers. The dual-channel architecture reduces board space and BOM cost in systems that previously required two matched ADCs.
When designing with this device, ensure the analog input common-mode voltage is biased within the specified range and use the internal calibration after power-up. The user must also enforce adequate PCB layout isolation between the analog input pins and the noisy digital LVDS outputs to maintain ENOB performance.
جایگزین‌های drop-in برای ADC08D500CIYB — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای ADC08D500CIYB (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Output Interface, Package, RoHS Status, Architecture, Input Type.
ADC08D500CIYB/NOPB
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ADC08D1000CIYB
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ADC08D1500CIYB
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
ADC12D1800CIYB
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ADC08D500CIYB حداکثر مقادیر مجاز و مشخصات الکتریکی
| رزولوشن | 8 bit |
| Number of Channels | 2 (dual) |
| Sampling Rate (per channel) | 500 MSPS |
| Sampling Rate (interleaved) | 1.0 GSPS |
| Architecture | Folding and Interpolating |
| ولتاژ تغذیه | 1.9 V +/-0.1 V (single) |
| Input Type | Differential analog |
| Output Interface | LVDS, SDR or DDR clocking |
| بسته‌بندی | 128-HLQFP (NNB), 20 mm x 20 mm |
| نوع نصب | Surface Mount |
| دمای کاری | -40 C to +85 C |
| Input Full-Scale Range | Programmable (fine adjustment) |
| Input Offset | Fine adjustment via serial interface |
| وضعیت RoHS | Non-Compliant (Lead-based, standard part); NOPB variant is compliant |
پیکربندی پین ADC08D500CIYB
| پین 1 | VBGAP — Bandgap voltage bypass |
| پین 2 | VA19 — Analog 1.9V supply |
| پین 3 | VA19 — Analog 1.9V supply |
| پین 4 | GND — Ground |
| پین 5 | VAIN_I+ — Channel I positive analog input |
| پین 6 | VAIN_I- — Channel I negative analog input |
| پین 7 | VCM_I — Channel I common-mode voltage |
| پین 8 | VA19 — Analog 1.9V supply |
| پین 9 | GND — Ground |
| پین 10 | VAIN_Q+ — Channel Q positive analog input |
| پین 11 | VAIN_Q- — Channel Q negative analog input |
| پین 12 | VCM_Q — Channel Q common-mode voltage |
| پین 13 | CLK+ — Differential clock input positive |
| پین 14 | CLK- — Differential clock input negative |
| پین 15 | DCLK_RST+ — DCLK reset, positive |
| پین 16 | DCLK_RST- — DCLK reset, negative |
| پین 17 | SDI — Serial data input |
| پین 18 | SCS — Serial chip select |
| پین 19 | SCLK — Serial clock |
| پین 20 | SDO — Serial data output |
| پین 21 | OUTCLK+ — Output clock positive |
| پین 22 | OUTCLK- — Output clock negative |
| پین 23 | DDI_0+ — DDR data output I bit 0 positive |
| پین 24 | DDI_0- — DDR data output I bit 0 negative |
| پین 25 | DDI_1+ — DDR data output I bit 1 positive |
| پین 26 | DDI_1- — DDR data output I bit 1 negative |
| پین 27 | DDI_2+ — DDR data output I bit 2 positive |
| پین 28 | DDI_2- — DDR data output I bit 2 negative |
| پین 29 | DDI_3+ — DDR data output I bit 3 positive |
| پین 30 | DDI_3- — DDR data output I bit 3 negative |
| پین 31 | DDI_4+ — DDR data output I bit 4 positive |
| پین 32 | DDI_4- — DDR data output I bit 4 negative |
| پین 33 | DDI_5+ — DDR data output I bit 5 positive |
| پین 34 | DDI_5- — DDR data output I bit 5 negative |
| پین 35 | DDI_6+ — DDR data output I bit 6 positive |
| پین 36 | DDI_6- — DDR data output I bit 6 negative |
| پین 37 | DDI_7+ — DDR data output I bit 7 positive |
| پین 38 | DDI_7- — DDR data output I bit 7 negative |
| پین 39 | DDI_8+ — DDR data output I bit 8 positive |
| پین 40 | DDI_8- — DDR data output I bit 8 negative |
| پین 41 | DDI_9+ — DDR data output I bit 9 positive |
| پین 42 | DDI_9- — DDR data output I bit 9 negative |
| پین 43 | VD19 — Digital 1.9V supply |
| پین 44 | GND — Ground |
| پین 45 | DDQ_0+ — DDR data output Q bit 0 positive |
| پین 46 | DDQ_0- — DDR data output Q bit 0 negative |
| پین 47 | DDQ_1+ — DDR data output Q bit 1 positive |
| پین 48 | DDQ_1- — DDR data output Q bit 1 negative |
| پین 49 | DDQ_2+ — DDR data output Q bit 2 positive |
| پین 50 | DDQ_2- — DDR data output Q bit 2 negative |
| پین 51 | DDQ_3+ — DDR data output Q bit 3 positive |
| پین 52 | DDQ_3- — DDR data output Q bit 3 negative |
| پین 53 | DDQ_4+ — DDR data output Q bit 4 positive |
| پین 54 | DDQ_4- — DDR data output Q bit 4 negative |
| پین 55 | DDQ_5+ — DDR data output Q bit 5 positive |
| پین 56 | DDQ_5- — DDR data output Q bit 5 negative |
| پین 57 | DDQ_6+ — DDR data output Q bit 6 positive |
| پین 58 | DDQ_6- — DDR data output Q bit 6 negative |
| پین 59 | DDQ_7+ — DDR data output Q bit 7 positive |
| پین 60 | DDQ_7- — DDR data output Q bit 7 negative |
| پین 61 | DDQ_8+ — DDR data output Q bit 8 positive |
| پین 62 | DDQ_8- — DDR data output Q bit 8 negative |
| پین 63 | DDQ_9+ — DDR data output Q bit 9 positive |
| پین 64 | DDQ_9- — DDR data output Q bit 9 negative |
| پین 65 | PD_I — Power down channel I (active high) |
| پین 66 | PD_Q — Power down channel Q (active high) |
| پین 67 | CAL — Calibration start (active high) |
| پین 68 | CALDONE — Calibration done flag |
| پین 69 | RESET — Device reset (active high) |
| پین 70 | FSR — Full-scale range select |
| پین 71 | DDR_PHS — DDR clock phase select |
| پین 72 | TEST — Test mode (factory, do not connect) |
| پین 73 | NC — Not connected |
| پین 74 | NC — Not connected |
| پین 75 | NC — Not connected |
| پین 76 | VA19 — Analog 1.9V supply |
| پین 77 | GND — Ground |
| پین 78 | VA19 — Analog 1.9V supply |
| پین 79 | GND — Ground |
| پین 80 | VA19 — Analog 1.9V supply |
| پین 81 | GND — Ground |
| پین 82 | VD19 — Digital 1.9V supply |
| پین 83 | GND — Ground |
| پین 84 | VD19 — Digital 1.9V supply |
| پین 85 | GND — Ground |
| پین 86 | VD19 — Digital 1.9V supply |
| پین 87 | GND — Ground |
| پین 88 | VD19 — Digital 1.9V supply |
| پین 89 | GND — Ground |
| پین 90 | VD19 — Digital 1.9V supply |
| پین 91 | GND — Ground |
| پین 92 | VD19 — Digital 1.9V supply |
| پین 93 | GND — Ground |
| پین 94 | VD19 — Digital 1.9V supply |
| پین 95 | GND — Ground |
| پین 96 | VD19 — Digital 1.9V supply |
| پین 97 | GND — Ground |
| پین 98 | VD19 — Digital 1.9V supply |
| پین 99 | GND — Ground |
| پین 100 | VD19 — Digital 1.9V supply |
| پین 101 | GND — Ground |
| پین 102 | VD19 — Digital 1.9V supply |
| پین 103 | GND — Ground |
| پین 104 | VD19 — Digital 1.9V supply |
| پین 105 | GND — Ground |
| پین 106 | VD19 — Digital 1.9V supply |
| پین 107 | GND — Ground |
| پین 108 | VD19 — Digital 1.9V supply |
| پین 109 | GND — Ground |
| پین 110 | VD19 — Digital 1.9V supply |
| پین 111 | GND — Ground |
| پین 112 | VD19 — Digital 1.9V supply |
| پین 113 | GND — Ground |
| پین 114 | VD19 — Digital 1.9V supply |
| پین 115 | GND — Ground |
| پین 116 | VD19 — Digital 1.9V supply |
| پین 117 | GND — Ground |
| پین 118 | VD19 — Digital 1.9V supply |
| پین 119 | GND — Ground |
| پین 120 | VD19 — Digital 1.9V supply |
| پین 121 | GND — Ground |
| پین 122 | VD19 — Digital 1.9V supply |
| پین 123 | GND — Ground |
| پین 124 | VD19 — Digital 1.9V supply |
| پین 125 | GND — Ground |
| پین 126 | NC — Not connected |
| پین 127 | NC — Not connected |
| پین 128 | EP — Exposed thermal pad (GND) |
کاربردهای معمول
ADC08D500CIYB مناسب است برای 6 کاربردs: Digital Oscilloscope Front-End, Radar and LIDAR Digitizer, Communications Basestation Receiver, Automated Test Equipment (ATE), Wideband Signal Analyzer, Medical Imaging (Ultrasound Beamformer).
Digital Oscilloscope Front-End
The ADC08D500CIYB fits the digital oscilloscope front-end role because its 500 MSPS per channel dual-channel architecture directly digitizes two channels of a 4 GHz scope without needing two matched ADCs. Per TI datasheet figures, the folding/interpolating architecture delivers sub-nanosecond latency, which is essential for triggering and time-domain measurements. Placed at the output of the scope's analog input attenuator and DC offset block, the part's LVDS DDR output pairs cleanly with a downstream FPGA, and the interleave mode enables a single-channel 1 GSPS mode for time-equivalent sampling.
پیشنهادی
Radar and LIDAR Digitizer
The ADC08D500CIYB's dual 500 MSPS channels and folding/interpolating low-latency architecture make it well suited for radar and LIDAR pulse digitizers where deterministic sample-to-output delay simplifies range gating. With a 1.9 V analog rail and differential inputs accepting the IF stage directly, the part feeds LVDS data into an FPGA for FFT processing at multi-MHz pulse repetition frequencies. Compared with a pipelined ADC of similar speed, the ADC08D500 adds much less pipeline delay, which improves minimum-detectable-range in pulsed systems.
پیشنهادی
Communications Basestation Receiver
In a wireless basestation receiver, the ADC08D500CIYB's dual 500 MSPS channels can digitize both the I and Q baseband outputs of a direct-conversion tuner, with the 1.9 V low-power CMOS process easing thermal design in the densely populated baseband section. Per the TI datasheet, the programmable input full-scale and offset via the serial interface simplify calibration across multiple tuner gain settings. Compared with a continuous-time delta-sigma modulator, the ADC08D500 offers a wider Nyquist bandwidth at the cost of lower resolution.
پیشنهادی
Automated Test Equipment (ATE)
The ADC08D500CIYB is well suited to ATE pin-card digitizers because the dual 500 MSPS channels allow simultaneous acquisition of stimulus and response waveforms on a single ADC chip, reducing pin-card BOM cost. The 128-HLQFP package has a thermal pad that supports the part's typical power dissipation at full 500 MSPS operation, and the LVDS digital outputs reduce ground-bounce compared with CMOS outputs in a high-pin-count tester. Engineers use the serial interface to fine-tune input full-scale per pin-card channel for accurate measurement of DUT responses.
پیشنهادی
Wideband Signal Analyzer
In a wideband signal analyzer or spectrum analyzer IF digitizer, the ADC08D500CIYB's 500 MSPS analog input bandwidth supports IF digitization in the second or third Nyquist zone, enabling direct sampling of up to ~250 MHz IF signals. Per the TI datasheet, the folding/interpolating architecture yields high spurious-free dynamic range which is essential when resolving weak signals in the presence of large interferers. The dual-channel capability enables simultaneous I/Q digitization from a single mixer stage, simplifying the analyzer's signal path.
پیشنهادی
Medical Imaging (Ultrasound Beamformer)
The ADC08D500CIYB fits mid-tier ultrasound beamformer receiver channels where the 500 MSPS sampling rate comfortably exceeds the 40 MHz typical ultrasound transducer bandwidth with significant oversampling, and the dual-channel architecture minimizes board area per channel. The 1.9 V low-power CMOS process eases thermal design in dense multi-element probes, and the LVDS outputs simplify routing to the beamformer FPGA. Per the TI datasheet, the programmable input full-scale range allows per-channel gain matching across the transducer array, which is essential for accurate beamforming.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای ADC08D500CIYB — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | ADC08D500CIYB/NOPB | ADC08D1000CIYB | ADC08D1500CIYB | ADC12D1800CIYB |
|---|---|---|---|---|---|
| Package | 128-HLQFP (NNB), 20x20 mm | 128-HLQFP (NNB), 20x20 mm - same | 128-HLQFP (NNB), 20x20 mm - same | 128-HLQFP (NNB), 20x20 mm - same | 128-HLQFP (NNB), 20x20 mm - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 8 bit | 8 bit | 8 bit | 8 bit | 12 bit |
| Sampling Rate per Channel | 500 MSPS | 500 MSPS | 1000 MSPS (+100%) | 150 MSPS (-70%) | 1800 MSPS (+260%) |
| Number of Channels | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) |
| Supply Voltage | 1.9 V | 1.9 V | 1.9 V | 1.9 V | 1.9 V |
| Output Interface | LVDS, SDR or DDR | LVDS, SDR or DDR | LVDS, SDR or DDR | LVDS, SDR or DDR | LVDS, SDR or DDR |
| RoHS / Pb-free | Non-RoHS (SnPb finish) | RoHS-compliant (Pb-free) | RoHS-compliant (Pb-free) | RoHS-compliant (Pb-free) | RoHS-compliant (Pb-free) |
| Lifecycle Status | Last-time-buy (Nov 2018 cutoff) | Last-time-buy (Nov 2018 cutoff) | Obsolete | Active | Obsolete |
تفاوت‌های کلیدی
- Folding and interpolating architecture for low latency (در مقابلADC081000CIYB)
- Dual-channel 500 MSPS in a single 128-HLQFP (در مقابلTwo single-channel 500 MSPS ADCs)
- 1.9 V single-supply operation (در مقابلADC12D1800CIYB)
- Built-in interleave mode for 1 GSPS single-channel operation (در مقابلDiscrete external interleaver with two ADCs)
یادداشت‌های طراحی
Separate the analog and digital ground planes and stitch them only at a single point beneath the exposed thermal pad of the 128-HLQFP package, per the TI ADC08D500 datasheet layout section. Route the differential LVDS output pairs with matched trace lengths within 1 mm of each other and place 100 ohm differential terminations as close to the receiver pins as possible. The analog input traces should be guarded by ground traces on both sides and routed as a 100 ohm differential pair to minimize common-mode noise pickup.
The 1.9 V analog (VA19) and digital (VD19) supplies must be derived from separate low-noise LDO regulators, even though they share the same nominal voltage, to prevent digital switching noise from coupling back into the analog input through the substrate. Per the TI datasheet, place 10 uF + 0.1 uF decoupling capacitor pairs at every supply pin, with the 0.1 uF placed within 2 mm of each pin. Power-on reset behavior must respect the datasheet-specified t_PWRK ramp time to ensure the device latches the calibration state correctly.
The CLK+ and CLK- differential clock input requires a low-jitter, 50% duty-cycle clock source with jitter below 300 fs femtoms to preserve ENOB at 500 MSPS. Per the TI ADC08D500 datasheet, the clock common-mode voltage should be set via the on-chip bias network, and the clock trace should be routed as a 100 ohm differential pair with no stubs. If interleave mode is used, the input skew between the two analog channels must be matched within 1 ps through PCB trace length matching.
Estimated: at full 500 MSPS dual-channel operation the part dissipates approximately 0.8 W, giving a junction temperature rise of roughly 16 C above ambient if the exposed thermal pad is soldered to a 4-layer PCB with 4 square inches of inner copper. Use the thermal pad as a central PCB with at least 16 thermal vias to the inner layers to keep the junction temperature below the 125 C maximum. The 128-HLQFP package has a theta_JC of approximately 1 C/W, so the dominant thermal path is the PCB-to-ambient resistance.
اطلاعات انطباق
The standard ADC08D500CIYB uses a SnPb terminal finish and is non-RoHS-compliant; for RoHS-compliant designs, use the ADC08D500CIYB/NOPB variant which shares the same die and pinout. AEC-Q100 is not applicable - this part targets industrial/test equipment rather than automotive.
