LM2902AWYPT - 1.3MHz Quad Op Amp, 14-TSSOP | STMicroelectronics
MPN: LM2902AWYPT ✓ فعالLM2902AWYPT نمای کلی
An operational amplifier is a high-gain, high-impedance differential amplifier whose closed-loop behavior is determined mainly by external feedback components. The quad LM2902A configuration places four independent amplifiers in one package, reducing component count and board area compared with four separate single or dual amplifier packages. In the broader semiconductor hierarchy, an operational amplifier is an analog IC, a signal-conditioning IC, and part of the wider linear and mixed-signal semiconductor family.
Key electrical attributes include a 1.3 MHz gain-bandwidth product, 100 dB common-mode rejection, and 375 µA typical quiescent current. The input bias-current figures listed for this device are 20 nA and 2 nA for different operating conditions, while its stated withstand voltage is 800 V. These characteristics make the LM2902AWYPT suitable for low-frequency instrumentation, sensor interfaces, transducers, and general feedback-control circuits where four amplifier channels can share a common supply architecture.
The push-pull output stage supports bidirectional output current without the crossover distortion commonly associated with older single-ended output designs. Each amplifier can implement non-inverting, inverting, summing, difference, comparator-style, or active-filter configurations when operated within its electrical limits. Independent channels allow one package to serve several signal paths, although each channel requires correct feedback and decoupling arrangements to prevent unintended oscillation or channel interaction.
Typical uses include low-frequency sensor conditioning, process-control instrumentation, current-voltage conversion, sample-and-hold circuitry, audio preamplification, active filtering, and general-purpose differential amplification. Four channels in one 14-TSSOP package can be especially useful in sensor nodes where several measurements must be conditioned before conversion or control. The package also supports compact mixed-signal boards where conserving board area is more important than very high slew rate or rail-to-rail input and output operation.
Designers should begin with the pin-description table and typical application circuits in the STMicroelectronics datasheet. Place the supply bypass capacitor close to the device, keep feedback-loop routing compact, and route each output only to its assigned load. Confirm that input and output common-mode voltages remain within the amplifier's permitted operating range and that source and load impedances preserve stability with the selected feedback network.
This product page consolidates the exact manufacturer-listing attributes, package information, commercially available replacement data, and application guidance for LM2902AWYPT. It also distinguishes verified electrical characteristics from parameters that require confirmation in the full manufacturer datasheet, helping engineers plan sourcing and circuit design with fewer documentation conflicts.
جایگزینهای drop-in برای LM2902AWYPT — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای LM2902AWYPT (همان فرمفاکتور و فوتپرینت) — متفاوت در Gain-Bandwidth Product, Package.
LM2902WYPT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2902KPWR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2902AWYPT حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | Low-power quad operational amplifier |
| Number of Amplifier Channels | 4 circuits |
| Gain-Bandwidth Product | 1.3 MHz |
| Common-Mode Rejection | 100 dB |
| جریان سکون | 375 µA |
| Input Bias Current | 20 nA |
| Input Offset Current | 2 nA |
| Withstand Voltage | 800 V |
| نوع خروجی | Push-pull |
| Application Classification | General-purpose amplifier |
| بستهبندی | 14-TSSOP |
| نوع نصب | Surface mount |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | unknown |
راهنمای پیکربندی پین LM2902AWYPT 14-tssop
پیکربندی پین برای LM2902AWYPT (پکیج 14-tssop). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای LM2902AWYPT.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
LM2902AWYPT مناسب است برای 6 کاربردs: Industrial Sensor Signal Conditioning, Precision Difference Amplifier, Low-Frequency Active Filtering, Process-Control Error Amplifier, Audio Preamplifier, Battery-Powered Instrumentation.
Industrial Sensor Signal Conditioning
The LM2902AWYPT is well suited to conditioning several low-frequency industrial sensor signals because it combines four general-purpose amplifier channels, a 1.3 MHz gain-bandwidth product, and 100 dB common-mode rejection in one 14-TSSOP package. Channels can implement instrumentation, difference, summing, or buffer stages around resistive sensors. Common-mode rejection helps suppress an offset or interference component that is common to both sensor inputs. The 375 µA quiescent current also reduces the standing current demand of multi-channel measurement circuits. Confirm the operating common-mode range, output swing, and sensor excitation level before implementation.
پیشنهادی
Precision Difference Amplifier
A pair of LM2902AWYPT channels can form a difference amplifier for rejecting common-mode voltage in bridge, current-loop, or sensing applications. The listed 100 dB common-mode rejection is the principal reason to select this device when the desired differential signal is small compared with a shared input voltage. The remaining two channels can provide output filtering or gain stages without adding another quad package. Since the device is not specified as rail-to-rail, verify input common-mode limits and output swing across the complete supply range used by the bridge sensor.
پیشنهادی
Low-Frequency Active Filtering
The LM2902AWYPT can implement first- and second-order low-frequency active filters when the required closed-loop bandwidth remains comfortably below its 1.3 MHz gain-bandwidth product. Four channels permit a filter followed by gain and buffer stages, reducing the number of amplifier packages in a compact analog board. Care should be taken to keep op-amp noise, gain error, and slew behavior compatible with the filter's frequency and amplitude requirements. Use the manufacturer's typical application circuits and stability guidance when choosing resistor and capacitor values around each amplifier channel.
پیشنهادی
Process-Control Error Amplifier
The LM2902AWYPT can implement the error amplifier and supporting conditioning functions in a low-frequency process-control loop. Its 1.3 MHz gain-bandwidth product provides useful closed-loop bandwidth for slow industrial control systems, while four channels can handle error amplification, sensor conditioning, filtering, and actuator-signal preparation. The 375 µA quiescent current is attractive for distributed low-power control nodes. Designers must account for output-swing limits when driving a control input and should verify stability with the compensation network and plant load used in the final control topology.
پیشنهادی
Audio Preamplifier
The LM2902AWYPT can provide low-frequency audio preamplification when the application does not require rail-to-rail operation or very high slew rate. Its four channels allow a stereo input stage, headphone or line-output driver, and an additional monitoring or filtering path to share a package. The push-pull output stage supports bidirectional output current, while the 1.3 MHz gain-bandwidth product covers audio-band signal paths. Confirm the maximum load current, output-voltage swing, noise requirements, and stability into the intended audio load before using the device in a production signal path.
پیشنهادی
Battery-Powered Instrumentation
The LM2902AWYPT is suitable for low-power instrumentation because its listed 375 µA quiescent current limits the no-load demand of four integrated amplifier channels. Engineers can use the channels for front-end amplification, active filtering, level shifting within the valid common-mode range, and output buffering. The 14-TSSOP package reduces board area compared with separate multi-amplifier packages. For battery systems, calculate the complete operating current including feedback-divider current and load demand, then confirm that shutdown requirements, if any, are satisfied by the control strategy rather than an assumed power-down function.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای LM2902AWYPT — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | LM2902WYPT | LM2902KPWR |
|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Amplifier Configuration | Quad | Quad | Quad |
| Product Classification | General-purpose amplifier | General-purpose amplifier | General-purpose amplifier |
| Number of Channels | 4 circuits | 4 circuits | 4 circuits |
| Mounting Type | Surface mount | Surface mount | Surface mount |
تفاوتهای کلیدی
- Four general-purpose amplifier channels in a compact package (در مقابلLM2902WYPT)
- Documented low-power operating headline (در مقابلLM2902KPWR)
- 1.3 MHz bandwidth supports moderate-frequency closed-loop stages (در مقابلLM2902WYPT)
یادداشتهای طراحی
Place the supply bypass capacitor immediately between the device supply and ground pins, following the connection shown in the manufacturer datasheet. Keep the capacitor's ground return short and avoid routing sensitive amplifier inputs beside switching nodes or high-current return paths. Because all four channels share the same package and supply pins, poor package-level decoupling can affect every amplifier simultaneously rather than only one signal chain.
Do not assume that a shared 14-TSSOP footprint guarantees drop-in compatibility. Compare the complete numbered pin map, exposed-pad connection, supply range, input common-mode limits, output swing, offset voltage, bias current, temperature grade, and qualification requirements. LM2902WYPT is the closest documented candidate because its product listing matches the 14-TSSOP package, quad configuration, and 1.3 MHz gain-bandwidth headline rating, but it still requires a formal datasheet cross-check.
Keep each op-amp feedback loop physically compact and route non-inverting inputs away from output and supply pins. Use a solid ground reference for the amplifier package and return feedback and decoupling currents directly to the device ground without passing through noisy analog signal paths. For instrumentation layouts, maintain symmetrical sensor connections when possible so cable and board parasitics do not degrade the benefit provided by the listed 100 dB common-mode rejection.
اطلاعات انطباق
The available manufacturer and distributor product summaries do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these requirements with STMicroelectronics before procurement.