LM2902AWYPT - 1.3MHz Quad Op Amp, 14-TSSOP | STMicroelectronics
MPN: LM2902AWYPT ✓ NakahandaLM2902AWYPT Ulas
An operational amplifier is a high-gain, high-impedance differential amplifier whose closed-loop behavior is determined mainly by external feedback components. The quad LM2902A configuration places four independent amplifiers in one package, reducing component count and board area compared with four separate single or dual amplifier packages. In the broader semiconductor hierarchy, an operational amplifier is an analog IC, a signal-conditioning IC, and part of the wider linear and mixed-signal semiconductor family.
Key electrical attributes include a 1.3 MHz gain-bandwidth product, 100 dB common-mode rejection, and 375 µA typical quiescent current. The input bias-current figures listed for this device are 20 nA and 2 nA for different operating conditions, while its stated withstand voltage is 800 V. These characteristics make the LM2902AWYPT suitable for low-frequency instrumentation, sensor interfaces, transducers, and general feedback-control circuits where four amplifier channels can share a common supply architecture.
The push-pull output stage supports bidirectional output current without the crossover distortion commonly associated with older single-ended output designs. Each amplifier can implement non-inverting, inverting, summing, difference, comparator-style, or active-filter configurations when operated within its electrical limits. Independent channels allow one package to serve several signal paths, although each channel requires correct feedback and decoupling arrangements to prevent unintended oscillation or channel interaction.
Typical uses include low-frequency sensor conditioning, process-control instrumentation, current-voltage conversion, sample-and-hold circuitry, audio preamplification, active filtering, and general-purpose differential amplification. Four channels in one 14-TSSOP package can be especially useful in sensor nodes where several measurements must be conditioned before conversion or control. The package also supports compact mixed-signal boards where conserving board area is more important than very high slew rate or rail-to-rail input and output operation.
Designers should begin with the pin-description table and typical application circuits in the STMicroelectronics datasheet. Place the supply bypass capacitor close to the device, keep feedback-loop routing compact, and route each output only to its assigned load. Confirm that input and output common-mode voltages remain within the amplifier's permitted operating range and that source and load impedances preserve stability with the selected feedback network.
This product page consolidates the exact manufacturer-listing attributes, package information, commercially available replacement data, and application guidance for LM2902AWYPT. It also distinguishes verified electrical characteristics from parameters that require confirmation in the full manufacturer datasheet, helping engineers plan sourcing and circuit design with fewer documentation conflicts.
Mga alternatibo na pwedeng ilagay na LM2902AWYPT — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok LM2902AWYPT (parehas na form factor at footprint) — pagkakaiba sa Gain-Bandwidth Product, Package.
LM2902WYPT
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM2902KPWR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM2902AWYPT Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | Low-power quad operational amplifier |
| Number of Amplifier Channels | 4 circuits |
| Gain-Bandwidth Product | 1.3 MHz |
| Common-Mode Rejection | 100 dB |
| Kuru-kuryente ng Kapayapaan | 375 µA |
| Input Bias Current | 20 nA |
| Input Offset Current | 2 nA |
| Withstand Voltage | 800 V |
| Type ng Output | Push-pull |
| Application Classification | General-purpose amplifier |
| Packhaging | 14-TSSOP |
| Uri ng Pagpapasok | Surface mount |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | unknown |
Gabay sa Pin Configuration ng LM2902AWYPT 14-tssop
Pin configuration para sa LM2902AWYPT (14-tssop package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa LM2902AWYPT.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LM2902AWYPT ay nararapat para sa 6 aplikasyons: Industrial Sensor Signal Conditioning, Precision Difference Amplifier, Low-Frequency Active Filtering, Process-Control Error Amplifier, Audio Preamplifier, Battery-Powered Instrumentation.
Industrial Sensor Signal Conditioning
The LM2902AWYPT is well suited to conditioning several low-frequency industrial sensor signals because it combines four general-purpose amplifier channels, a 1.3 MHz gain-bandwidth product, and 100 dB common-mode rejection in one 14-TSSOP package. Channels can implement instrumentation, difference, summing, or buffer stages around resistive sensors. Common-mode rejection helps suppress an offset or interference component that is common to both sensor inputs. The 375 µA quiescent current also reduces the standing current demand of multi-channel measurement circuits. Confirm the operating common-mode range, output swing, and sensor excitation level before implementation.
Inirekomenda
Precision Difference Amplifier
A pair of LM2902AWYPT channels can form a difference amplifier for rejecting common-mode voltage in bridge, current-loop, or sensing applications. The listed 100 dB common-mode rejection is the principal reason to select this device when the desired differential signal is small compared with a shared input voltage. The remaining two channels can provide output filtering or gain stages without adding another quad package. Since the device is not specified as rail-to-rail, verify input common-mode limits and output swing across the complete supply range used by the bridge sensor.
Inirekomenda
Low-Frequency Active Filtering
The LM2902AWYPT can implement first- and second-order low-frequency active filters when the required closed-loop bandwidth remains comfortably below its 1.3 MHz gain-bandwidth product. Four channels permit a filter followed by gain and buffer stages, reducing the number of amplifier packages in a compact analog board. Care should be taken to keep op-amp noise, gain error, and slew behavior compatible with the filter's frequency and amplitude requirements. Use the manufacturer's typical application circuits and stability guidance when choosing resistor and capacitor values around each amplifier channel.
Inirekomenda
Process-Control Error Amplifier
The LM2902AWYPT can implement the error amplifier and supporting conditioning functions in a low-frequency process-control loop. Its 1.3 MHz gain-bandwidth product provides useful closed-loop bandwidth for slow industrial control systems, while four channels can handle error amplification, sensor conditioning, filtering, and actuator-signal preparation. The 375 µA quiescent current is attractive for distributed low-power control nodes. Designers must account for output-swing limits when driving a control input and should verify stability with the compensation network and plant load used in the final control topology.
Inirekomenda
Audio Preamplifier
The LM2902AWYPT can provide low-frequency audio preamplification when the application does not require rail-to-rail operation or very high slew rate. Its four channels allow a stereo input stage, headphone or line-output driver, and an additional monitoring or filtering path to share a package. The push-pull output stage supports bidirectional output current, while the 1.3 MHz gain-bandwidth product covers audio-band signal paths. Confirm the maximum load current, output-voltage swing, noise requirements, and stability into the intended audio load before using the device in a production signal path.
Inirekomenda
Battery-Powered Instrumentation
The LM2902AWYPT is suitable for low-power instrumentation because its listed 375 µA quiescent current limits the no-load demand of four integrated amplifier channels. Engineers can use the channels for front-end amplification, active filtering, level shifting within the valid common-mode range, and output buffering. The 14-TSSOP package reduces board area compared with separate multi-amplifier packages. For battery systems, calculate the complete operating current including feedback-divider current and load demand, then confirm that shutdown requirements, if any, are satisfied by the control strategy rather than an assumed power-down function.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM2902AWYPT — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LM2902WYPT | LM2902KPWR |
|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Amplifier Configuration | Quad | Quad | Quad |
| Product Classification | General-purpose amplifier | General-purpose amplifier | General-purpose amplifier |
| Number of Channels | 4 circuits | 4 circuits | 4 circuits |
| Mounting Type | Surface mount | Surface mount | Surface mount |
Pangunahing mga Pagkakaiba
- Four general-purpose amplifier channels in a compact package (kumpara saLM2902WYPT)
- Documented low-power operating headline (kumpara saLM2902KPWR)
- 1.3 MHz bandwidth supports moderate-frequency closed-loop stages (kumpara saLM2902WYPT)
Talaan ng Disenyo
Place the supply bypass capacitor immediately between the device supply and ground pins, following the connection shown in the manufacturer datasheet. Keep the capacitor's ground return short and avoid routing sensitive amplifier inputs beside switching nodes or high-current return paths. Because all four channels share the same package and supply pins, poor package-level decoupling can affect every amplifier simultaneously rather than only one signal chain.
Do not assume that a shared 14-TSSOP footprint guarantees drop-in compatibility. Compare the complete numbered pin map, exposed-pad connection, supply range, input common-mode limits, output swing, offset voltage, bias current, temperature grade, and qualification requirements. LM2902WYPT is the closest documented candidate because its product listing matches the 14-TSSOP package, quad configuration, and 1.3 MHz gain-bandwidth headline rating, but it still requires a formal datasheet cross-check.
Keep each op-amp feedback loop physically compact and route non-inverting inputs away from output and supply pins. Use a solid ground reference for the amplifier package and return feedback and decoupling currents directly to the device ground without passing through noisy analog signal paths. For instrumentation layouts, maintain symmetrical sensor connections when possible so cable and board parasitics do not degrade the benefit provided by the listed 100 dB common-mode rejection.
Impormasyon ng Pagsunod sa Kautusan
The available manufacturer and distributor product summaries do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these requirements with STMicroelectronics before procurement.