LM2902AWYPT - 1.3MHz Quad Op Amp, 14-TSSOP | STMicroelectronics
MPN: LM2902AWYPT ✓ सक्रियLM2902AWYPT अवलोकन
An operational amplifier is a high-gain, high-impedance differential amplifier whose closed-loop behavior is determined mainly by external feedback components. The quad LM2902A configuration places four independent amplifiers in one package, reducing component count and board area compared with four separate single or dual amplifier packages. In the broader semiconductor hierarchy, an operational amplifier is an analog IC, a signal-conditioning IC, and part of the wider linear and mixed-signal semiconductor family.
Key electrical attributes include a 1.3 MHz gain-bandwidth product, 100 dB common-mode rejection, and 375 µA typical quiescent current. The input bias-current figures listed for this device are 20 nA and 2 nA for different operating conditions, while its stated withstand voltage is 800 V. These characteristics make the LM2902AWYPT suitable for low-frequency instrumentation, sensor interfaces, transducers, and general feedback-control circuits where four amplifier channels can share a common supply architecture.
The push-pull output stage supports bidirectional output current without the crossover distortion commonly associated with older single-ended output designs. Each amplifier can implement non-inverting, inverting, summing, difference, comparator-style, or active-filter configurations when operated within its electrical limits. Independent channels allow one package to serve several signal paths, although each channel requires correct feedback and decoupling arrangements to prevent unintended oscillation or channel interaction.
Typical uses include low-frequency sensor conditioning, process-control instrumentation, current-voltage conversion, sample-and-hold circuitry, audio preamplification, active filtering, and general-purpose differential amplification. Four channels in one 14-TSSOP package can be especially useful in sensor nodes where several measurements must be conditioned before conversion or control. The package also supports compact mixed-signal boards where conserving board area is more important than very high slew rate or rail-to-rail input and output operation.
Designers should begin with the pin-description table and typical application circuits in the STMicroelectronics datasheet. Place the supply bypass capacitor close to the device, keep feedback-loop routing compact, and route each output only to its assigned load. Confirm that input and output common-mode voltages remain within the amplifier's permitted operating range and that source and load impedances preserve stability with the selected feedback network.
This product page consolidates the exact manufacturer-listing attributes, package information, commercially available replacement data, and application guidance for LM2902AWYPT. It also distinguishes verified electrical characteristics from parameters that require confirmation in the full manufacturer datasheet, helping engineers plan sourcing and circuit design with fewer documentation conflicts.
के लिए ड्रॉप-इन विकल्प LM2902AWYPT — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM2902AWYPT (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Gain-Bandwidth Product, Package.
LM2902WYPT
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2902KPWR
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2902AWYPT Maximum Ratings और Electrical Characteristics
| Product Type | Low-power quad operational amplifier |
| Number of Amplifier Channels | 4 circuits |
| Gain-Bandwidth Product | 1.3 MHz |
| Common-Mode Rejection | 100 dB |
| क्वाइसेंट करंट | 375 µA |
| Input Bias Current | 20 nA |
| Input Offset Current | 2 nA |
| Withstand Voltage | 800 V |
| आउटपुट प्रकार | Push-pull |
| Application Classification | General-purpose amplifier |
| पैकेज | 14-TSSOP |
| माउंटिंग प्रकार | Surface mount |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | unknown |
LM2902AWYPT 14-tssop पिन कॉन्फ़िगरेशन गाइड
LM2902AWYPT (14-tssop पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: LM2902AWYPT.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
LM2902AWYPT के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Signal Conditioning, Precision Difference Amplifier, Low-Frequency Active Filtering, Process-Control Error Amplifier, Audio Preamplifier, Battery-Powered Instrumentation.
Industrial Sensor Signal Conditioning
The LM2902AWYPT is well suited to conditioning several low-frequency industrial sensor signals because it combines four general-purpose amplifier channels, a 1.3 MHz gain-bandwidth product, and 100 dB common-mode rejection in one 14-TSSOP package. Channels can implement instrumentation, difference, summing, or buffer stages around resistive sensors. Common-mode rejection helps suppress an offset or interference component that is common to both sensor inputs. The 375 µA quiescent current also reduces the standing current demand of multi-channel measurement circuits. Confirm the operating common-mode range, output swing, and sensor excitation level before implementation.
अनुशंसित
Precision Difference Amplifier
A pair of LM2902AWYPT channels can form a difference amplifier for rejecting common-mode voltage in bridge, current-loop, or sensing applications. The listed 100 dB common-mode rejection is the principal reason to select this device when the desired differential signal is small compared with a shared input voltage. The remaining two channels can provide output filtering or gain stages without adding another quad package. Since the device is not specified as rail-to-rail, verify input common-mode limits and output swing across the complete supply range used by the bridge sensor.
अनुशंसित
Low-Frequency Active Filtering
The LM2902AWYPT can implement first- and second-order low-frequency active filters when the required closed-loop bandwidth remains comfortably below its 1.3 MHz gain-bandwidth product. Four channels permit a filter followed by gain and buffer stages, reducing the number of amplifier packages in a compact analog board. Care should be taken to keep op-amp noise, gain error, and slew behavior compatible with the filter's frequency and amplitude requirements. Use the manufacturer's typical application circuits and stability guidance when choosing resistor and capacitor values around each amplifier channel.
अनुशंसित
Process-Control Error Amplifier
The LM2902AWYPT can implement the error amplifier and supporting conditioning functions in a low-frequency process-control loop. Its 1.3 MHz gain-bandwidth product provides useful closed-loop bandwidth for slow industrial control systems, while four channels can handle error amplification, sensor conditioning, filtering, and actuator-signal preparation. The 375 µA quiescent current is attractive for distributed low-power control nodes. Designers must account for output-swing limits when driving a control input and should verify stability with the compensation network and plant load used in the final control topology.
अनुशंसित
Audio Preamplifier
The LM2902AWYPT can provide low-frequency audio preamplification when the application does not require rail-to-rail operation or very high slew rate. Its four channels allow a stereo input stage, headphone or line-output driver, and an additional monitoring or filtering path to share a package. The push-pull output stage supports bidirectional output current, while the 1.3 MHz gain-bandwidth product covers audio-band signal paths. Confirm the maximum load current, output-voltage swing, noise requirements, and stability into the intended audio load before using the device in a production signal path.
अनुशंसित
Battery-Powered Instrumentation
The LM2902AWYPT is suitable for low-power instrumentation because its listed 375 µA quiescent current limits the no-load demand of four integrated amplifier channels. Engineers can use the channels for front-end amplification, active filtering, level shifting within the valid common-mode range, and output buffering. The 14-TSSOP package reduces board area compared with separate multi-amplifier packages. For battery systems, calculate the complete operating current including feedback-divider current and load demand, then confirm that shutdown requirements, if any, are satisfied by the control strategy rather than an assumed power-down function.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LM2902AWYPT — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LM2902WYPT | LM2902KPWR |
|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Amplifier Configuration | Quad | Quad | Quad |
| Product Classification | General-purpose amplifier | General-purpose amplifier | General-purpose amplifier |
| Number of Channels | 4 circuits | 4 circuits | 4 circuits |
| Mounting Type | Surface mount | Surface mount | Surface mount |
मुख्य विशेषताएँ
- Four general-purpose amplifier channels in a compact package (बनामLM2902WYPT)
- Documented low-power operating headline (बनामLM2902KPWR)
- 1.3 MHz bandwidth supports moderate-frequency closed-loop stages (बनामLM2902WYPT)
डिज़ाइन नोट्स
Place the supply bypass capacitor immediately between the device supply and ground pins, following the connection shown in the manufacturer datasheet. Keep the capacitor's ground return short and avoid routing sensitive amplifier inputs beside switching nodes or high-current return paths. Because all four channels share the same package and supply pins, poor package-level decoupling can affect every amplifier simultaneously rather than only one signal chain.
Do not assume that a shared 14-TSSOP footprint guarantees drop-in compatibility. Compare the complete numbered pin map, exposed-pad connection, supply range, input common-mode limits, output swing, offset voltage, bias current, temperature grade, and qualification requirements. LM2902WYPT is the closest documented candidate because its product listing matches the 14-TSSOP package, quad configuration, and 1.3 MHz gain-bandwidth headline rating, but it still requires a formal datasheet cross-check.
Keep each op-amp feedback loop physically compact and route non-inverting inputs away from output and supply pins. Use a solid ground reference for the amplifier package and return feedback and decoupling currents directly to the device ground without passing through noisy analog signal paths. For instrumentation layouts, maintain symmetrical sensor connections when possible so cable and board parasitics do not degrade the benefit provided by the listed 100 dB common-mode rejection.
अनुपालन जानकारी
The available manufacturer and distributor product summaries do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these requirements with STMicroelectronics before procurement.