LM324ADTBG - 4-Channel 3-32V Op Amp | onsemi | TSSOP-14
MPN: LM324ADTBG ✓ فعالLM324ADTBG نمای کلی
An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to increase the voltage difference between its two inputs. The quad operational-amplifier category groups four amplifiers in one package, reducing board area compared with four discrete single amplifiers. Within the broader hierarchy, the LM324 belongs to the amplifier IC and signal-chain categories, with applications spanning instrumentation, industrial control, sensor interfaces, and power-management circuits.
Key characteristics include a 3 V to 32 V supply range, approximately 0.6 V/µs slew rate, 3 mV typical input-offset voltage, and 2 nA typical input-offset current. The device can operate with a single positive supply or split supplies, while its common-mode input range includes ground. These characteristics make it useful for battery-powered equipment and other low-voltage systems where the input signal may approach the lower supply rail.
The four internal amplifiers use true differential input stages and are internally frequency compensated for unity-gain operation. The approximate 1 MHz gain-bandwidth product favors moderate-speed applications rather than precision signal paths demanding megahertz bandwidth or microvolt-level offset. Typical offset-current behavior supports high-impedance sensing, but source impedance must still be balanced to minimize offset and bias-current errors.
Typical uses include current-to-voltage conversion in sensor interfaces, audio preamplification, comparator-style thresholding, active filtering, relay driving, and low-side current monitoring. The four amplifiers can also implement independent sensor channels, instrument loops, or gain stages where package size and cost matter more than precision or slew rate.
When laying out the circuit, place input resistors close to the noninverting and inverting pins to reduce parasitic pickup, especially with high source impedance. Decoupling capacitors should be connected from each supply pin to ground with a short return path. Keep sensitive input traces away from switching nodes and provide adequate output-current headroom for capacitive loads because the LM324 is not rail-to-rail.
This product guide combines package information, functional application guidance, selection criteria, and pin-compatible alternatives to simplify footprint planning and sourcing. For exact lead assignments, electrical limits, and ordering details, use the manufacturer datasheet and the technical information linked on this page.
جایگزینهای drop-in برای LM324ADTBG — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای LM324ADTBG (همان فرمفاکتور و فوتپرینت) — متفاوت در Gain-Bandwidth Product, Input Offset Voltage, Package.
LM324APWR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TLV324IPWR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
LMV324IPWR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TLV9004IPWR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCP6004-I/ST
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
LM324ADTBG حداکثر مقادیر مجاز و مشخصات الکتریکی
| Number of Amplifiers | 4 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Supply Voltage Range | 3 V to 32 V |
| Gain-Bandwidth Product | Approximately 1 MHz |
| Slew Rate | 0.6 V/µs |
| Input Offset Voltage | 3 mV typical |
| Input Offset Current | 2 nA typical |
| Supply Current per Amplifier | 0.8 mA typical |
| ESD Protection | 2 kV |
| Input Configuration | True differential |
| Compensation | Internally frequency compensated |
| Common-Mode Input Range | Includes ground |
| بستهبندی | 14-pin TSSOP |
| نوع نصب | Surface mount |
| نوع خروجی | Push-pull |
راهنمای پیکربندی پین LM324ADTBG 14-pin tssop
پیکربندی پین برای LM324ADTBG (پکیج 14-pin tssop). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای LM324ADTBG.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
LM324ADTBG مناسب است برای 6 کاربردs: Low-Cost Sensor Signal Conditioning, Industrial Current Monitoring, Audio Preamplifier, Active Filtering and Thresholding, Power-Supply Feedback and Control, Portable and Battery-Powered Equipment.
Low-Cost Sensor Signal Conditioning
The LM324ADTBG suits general-purpose conditioning of sensor signals that operate within a 3 V to 32 V supply environment. Its true differential inputs support amplification of small differential voltages, while the common-mode input range including ground is useful for sensors referenced to the lower rail. The approximately 1 MHz gain-bandwidth product is adequate for moderate-bandwidth measurements, but the 3 mV typical offset can dominate low-level sensor outputs. Designers should therefore use calibration or offset trimming when accuracy requirements exceed the LM324A’s normal general-purpose performance.
پیشنهادی
Industrial Current Monitoring
For low-side or high-side current monitoring with moderate bandwidth, the LM324ADTBG can amplify the voltage generated by a sense resistor and buffer the result for an ADC or controller. Its four channels allow several measurement points to be handled in one package, and the 0.6 V/µs slew rate supports relatively slow feedback loops. The 3 mV typical input-offset voltage translates directly into sensing error across the shunt resistor, so precision systems should include offset calibration or select a lower-offset amplifier.
پیشنهادی
Audio Preamplifier
The LM324ADTBG can provide gain for microphone, line, or headphone-driver stages when cost and simplicity are more important than low distortion. Four amplifiers in a single 14-pin TSSOP reduce board area, and unity-gain stability simplifies first-stage implementation. The approximately 1 MHz bandwidth and 0.6 V/µs slew rate limit high-frequency and large-signal performance, while the device is not rail-to-rail. Headphone and line-output designs should verify voltage swing, load impedance, and distortion against the actual supply voltage.
پیشنهادی
Active Filtering and Thresholding
The LM324ADTBG is well suited to first-order or low-order active filters, peak detectors, window comparators, and threshold circuits in general-purpose control equipment. Its internally compensated amplifiers support stable unity-gain operation, and the 14-pin TSSOP provides four channels for compact filter or conditioning networks. Component tolerances and the 3 mV input offset can shift filter and switching thresholds, so production designs should include realistic tolerance analysis and calibration where repeatable thresholds are important.
پیشنهادی
Power-Supply Feedback and Control
The LM324ADTBG can supervise a regulated rail, amplify the difference between a feedback node and a reference, or form part of a slow analog regulation loop. Its operation from 3 V to 32 V permits use in both compact low-voltage systems and higher-voltage industrial supplies. The non-rail-to-rail output and 3 mV typical offset limit sensing accuracy near either rail, while the approximately 1 MHz bandwidth is more than adequate for many slow control loops. Stable feedback layout and decoupling should be verified in the final power-supply design.
پیشنهادی
Portable and Battery-Powered Equipment
The LM324ADTBG can amplify signals in portable equipment because its specified supply operation begins at 3 V and the common-mode input range includes ground. Four amplifiers are available for a compact multi-channel implementation, reducing both package count and board area. The typical per-amplifier supply current is 0.8 mA, making the device practical for modest-power systems. Its input-offset voltage remains the main precision limitation, and its non-rail-to-rail output requires attention when signals approach the upper supply rail.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای LM324ADTBG — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | LM324APWR | TLV324IPWR | LMV324IPWR | TLV9004IPWR | MCP6004-I/ST |
|---|---|---|---|---|---|---|
| Package | TSSOP-14 | TSSOP-14 | TSSOP-14 | TSSOP-14 | TSSOP-14 | TSSOP-14 |
| Brand | onsemi | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Microchip Technology |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 4 |
تفاوتهای کلیدی
- Supports a wide single-supply operating range (در مقابلMCP6004-I/ST)
- Maintains approximately 1 MHz bandwidth in a four-channel package (در مقابلTLV9004IPWR)
- Provides direct onsemi family continuity (در مقابلLM324APWR)
یادداشتهای طراحی
Place the LM324ADTBG input and feedback components close to the associated amplifier pins. Keep each noninverting and inverting route short and symmetrical where possible, particularly in high-impedance sensor circuits. Connect supply decoupling directly between the supply pins and ground, and provide a low-impedance ground return. Avoid routing sensitive input traces beneath digital, relay, or switching-regulator paths.
Do not treat the LM324ADTBG as a precision or rail-to-rail amplifier. Its 3 mV typical input-offset voltage can create visible error in low-level measurements, and output swing is limited near the supply rails. The common-mode input range includes ground, but that does not make the output rail-to-rail. Verify signal amplitude, headroom, and output load against the manufacturer electrical-characteristics curves before finalizing analog gains.
Balance the source impedances seen by each input because input-bias current can create additional offset when unequal impedances are used. For capacitive loads, add an isolation resistor close to the output and verify stability with the actual load and PCB capacitance. The approximately 1 MHz bandwidth is suitable for general-purpose conditioning, but it does not support high-speed closed-loop layouts or large capacitive loads without additional compensation.
The 14-pin TSSOP is intended for surface-mount assembly and ordinary PCB thermal management. Its small lead area limits heat dissipation compared with larger packages, so monitor channel dissipation when driving low-resistance or capacitive loads. Keep the device away from nearby heat sources and maintain copper around the package when its operating environment is elevated. Follow the manufacturer maximum ratings for junction temperature and supply voltage.
اطلاعات انطباق
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current onsemi product documentation or supplier declaration.