MCP3422A1-E/MC - 18-Bit Dual-Channel ADC | Microchip
MPN: MCP3422A1-E/MC ✓ فعالMCP3422A1-E/MC نمای کلی
A delta-sigma ADC is a voltage-regulating class of data-conversion IC that uses continuous-time or sampled internal signals to measure an analog differential voltage. Its hierarchy is ADC > delta-sigma ADC > data converter > integrated circuit. The architecture favors high resolution and low noise rather than very high conversion speed, making this device appropriate for slowly changing sensor signals rather than waveform or high-speed acquisition systems.
Key features include two differential input channels, resolution up to 18 bits, an integrated 2.048 V reference, and a 240 SPS maximum conversion rate identified for the MCP3422A1-E/MC. The I2C interface reduces the number of signal lines required from a sensor module to the host controller. Differential measurement also helps reject common-mode noise when the two input wires experience similar external interference.
The MCP3422 family uses a delta-sigma conversion architecture optimized for precision measurement. Its resolution and reference arrangement support high-accuracy measurements of low-level analog signals, while differential inputs can be connected to sensor bridges, potentiometers, or other balanced sensing networks. The 8-DFN package minimizes PCB area, but its exposed pad and thermal requirements must be considered when laying out the board and setting copper coverage.
Typical applications include industrial pressure and temperature acquisition, current monitoring, laboratory measurement instruments, portable sensor nodes, and process-control equipment. Two channels can measure a differential sensor pair or two related inputs, while the digital interface allows readings to be transferred directly to an MCU or embedded controller. For applications requiring faster conversion, designers should select a different ADC rather than increase the load on this converter.
Place input, reference, and decoupling capacitors close to their associated pins, keep analog routing away from switching nodes, and connect the exposed pad to a properly sized ground plane. Confirm the differential input range, gain configuration, conversion time, I2C address, and acquisition sequence against the manufacturer's datasheet before finalizing the analog front end.
This page combines the MCP3422A1-E/MC electrical characteristics, package details, pin-compatible family alternatives, comparison parameters, and practical PCB guidance. It is intended to help engineers evaluate the converter, select an appropriate replacement, and integrate a compact, low-noise differential measurement channel without relying on raw catalog summaries alone.
جایگزینهای drop-in برای MCP3422A1-E/MC — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای MCP3422A1-E/MC (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Differential Input Range, Digital Interface, Automotive Qualification, Resolution.
MCP3422A0-E/MC
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3422A5-E/MC
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3422A6-E/MC
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3422A2-E/MC
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3422A3-E/MC
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3422A1-E/MC حداکثر مقادیر مجاز و مشخصات الکتریکی
| Converter Type | Delta-sigma ADC |
| رزولوشن | 18 bits |
| Number of Input Channels | 2 channels |
| Input Type | Differential |
| Maximum Conversion Rate | 240 samples per second |
| Integrated Reference Voltage | 2.048 V |
| Differential Input Range | ±2.048 V |
| Minimum Supply Voltage | 2.7 V |
| Maximum Supply Voltage | 5.5 V |
| Minimum Operating Temperature | -40 °C |
| Maximum Operating Temperature | 125 °C |
| Digital Interface | 2-wire I2C |
| بستهبندی | 8-DFN, 2 x 3 mm |
| نوع نصب | Surface mount |
| Exposed Pad | Present |
| Shipping Form | Tape and reel |
| Automotive Classification | Automotive for MCP3422A6-E/MC |
راهنمای پیکربندی پین MCP3422A1-E/MC 8-dfn, 2 x 3 mm
پیکربندی پین برای MCP3422A1-E/MC (پکیج 8-dfn, 2 x 3 mm). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای MCP3422A1-E/MC.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
MCP3422A1-E/MC مناسب است برای 6 کاربردs: Industrial Pressure Sensor Acquisition, Precision Temperature Measurement, Battery-Powered Sensor Nodes, Current and Power Monitoring, Laboratory and Test Instruments, Process Control and Instrumentation.
Industrial Pressure Sensor Acquisition
The MCP3422A1-E/MC fits bridge-based pressure sensing because it provides two differential input channels, up to 18 bits of resolution, and a 240 SPS conversion rate for slowly varying process signals. The integrated 2.048 V reference supplies a stable excitation and conversion reference, while differential measurement helps suppress common-mode voltage present on long industrial sensor cables. Place the converter close to the sensor input, route the pair as a balanced analog channel, and use the manufacturer-recommended input filtering. Its I2C interface allows the readings to be transferred directly to an embedded controller without requiring a parallel data bus.
پیشنهادی
Precision Temperature Measurement
The MCP3422A1-E/MC is suitable for RTD, thermocouple, or semiconductor temperature sensing when the measured value changes relatively slowly. Its 18-bit resolution preserves small temperature-derived voltage changes, and the two differential channels can monitor a sensing element or provide a reference measurement for drift compensation. The 240 SPS maximum rate is sufficient for thermal monitoring but should not be confused with a high-speed temperature waveform converter. A low-drift signal-conditioning path, shielded differential routing, and careful reference decoupling are necessary to preserve the converter's resolution in practical measurements.
پیشنهادی
Battery-Powered Sensor Nodes
The MCP3422A1-E/MC is appropriate for compact battery-powered sensor nodes that periodically report slowly changing measurements through I2C. Its 2.7 V to 5.5 V operating range supports common low-energy rails, while the 8-DFN 2 x 3 mm package preserves board area. The 18-bit resolution reduces the need for gain that could amplify offset and noise, and the integrated 2.048 V reference simplifies the measurement chain. Designers should still account for reference accuracy, analog input current, I2C pull-up consumption, and the converter's energy use during each acquisition cycle.
پیشنهادی
Current and Power Monitoring
The MCP3422A1-E/MC can measure low differential voltages produced by shunt resistors in current or power-monitoring circuits. Differential inputs suit a bipolar measurement around ground, while 18-bit resolution supports useful resolution when the shunt voltage occupies only a small part of the converter range. The two channels can monitor two power branches or provide simultaneous measurement of a load and a reference channel. Accurate results depend on an appropriate shunt value, input protection, Kelvin-style routing where practical, and analog filtering that does not introduce excessive settling delay at the selected conversion rate.
پیشنهادی
Laboratory and Test Instruments
The MCP3422A1-E/MC is useful in compact laboratory instruments that require accurate DC measurements but do not need waveform acquisition. Two differential channels can monitor an unknown input and a precision reference, supporting self-calibration or ratio measurements. The integrated 2.048 V reference simplifies instrument design, and the I2C interface allows a controller to retrieve results while minimizing interconnects. For bench equipment, isolate analog and digital grounds appropriately, keep input conditioning close to the package, and verify that the 240 SPS conversion rate supports the operator's measurement workflow.
پیشنهادی
Process Control and Instrumentation
The MCP3422A1-E/MC can digitize low-level process variables in compact industrial instrumentation where panel space is constrained. Two differential inputs allow simultaneous acquisition of a process signal and a feedback or status channel, while the 18-bit delta-sigma architecture emphasizes resolution and noise performance. The I2C interface can connect the converter to a supervisory controller that performs scaling, filtering, and alarm logic. For reliable operation near motors, relays, or switching supplies, use a narrow analog trace path, continuous reference bypassing, an appropriate grounding strategy, and input protection selected for the actual transient environment.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای MCP3422A1-E/MC — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MCP3422A0-E/MC | MCP3422A5-E/MC | MCP3422A6-E/MC | MCP3422A2-E/MC | MCP3422A3-E/MC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm), same package | 8-DFN (2 x 3 mm), same package | 8-DFN (2 x 3 mm), same package | 8-DFN (2 x 3 mm), same package | 8-DFN (2 x 3 mm), same package |
| Resolution | 18 bits | 18 bits | 18 bits | 18 bits | 18 bits | 18 bits |
| Input Channels | 2 differential channels | 2 differential channels | 2 differential channels | 2 differential channels | 2 differential channels | 2 differential channels |
| Conversion Rate | 240 SPS | 240 SPS | 240 SPS | 240 SPS | 240 SPS | 240 SPS |
| Integrated Reference | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Operating Temperature Range | -40 °C to 125 °C | -40 °C to 125 °C | -40 °C to 125 °C | -40 °C to 125 °C | -40 °C to 125 °C | -40 °C to 125 °C |
| Digital Interface | 2-wire I2C | 2-wire I2C | 2-wire I2C | 2-wire I2C | 2-wire I2C | 2-wire I2C |
تفاوتهای کلیدی
- High-resolution conversion in a compact package (در مقابلMCP3422A0-E/MC)
- Automotive-oriented family option (در مقابلMCP3422A1-E/MC)
- Compact two-channel differential measurement (در مقابلMCP3422A2-E/MC)
یادداشتهای طراحی
Place the MCP3422A1-E/MC close to the sensor connector and route the two differential inputs as a compact pair. Use a continuous ground plane beneath the analog section, connect the exposed pad to ground according to the manufacturer land pattern, and place the recommended input, reference, and supply capacitors adjacent to their pins. Avoid routing the analog pair beneath switching-power nodes, relay contacts, or digital clock lines.
Do not treat 18-bit resolution as guaranteed system accuracy. Offset, reference drift, analog front-end noise, ADC noise, PCB leakage, and signal-conditioning errors can dominate the nominal resolution. Establish the required measurement uncertainty, characterize the complete channel at the intended temperature and bandwidth, and keep the input common-mode voltage within the operating range shown in the manufacturer datasheet.
Use differential pair routing with consistent geometry, minimize stubs, and ground the unused input appropriately when the application permits. Place analog filtering close to the ADC and verify that its settling behavior is compatible with the selected gain and conversion timing. I2C pull-up resistors can inject transient current into the power rail, so decouple the analog and digital supplies effectively and keep I2C routing away from the sensitive input nodes.
اطلاعات انطباق
Compliance declarations for the exact MCP3422A1-E/MC orderable part were not identified. MCP3422A6-E/MC is identified as automotive-classified, but that classification should not be assigned to MCP3422A1-E/MC.