ATSAME54N19A-AU-EFP - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip
Référence : ATSAME54N19A-AU-EFP ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $11.2 | $11,20 |
| 10 | $10.08 | $100,80 |
| 100 | $8.96 | $896,00 |
| 500 | $8.06 | $4 030,00 |
| 1 000 | $7.28 | $7 280,00 |
ATSAME54N19A-AU-EFP Présentation
Key features include a 120 MHz Cortex-M4F core, 512 KB dual-panel Flash with ECC, 192 KB SRAM with ECC, full-speed USB 2.0 with integrated PHY, 10/100 Mbps Ethernet MAC with IEEE 1588 support, CAN-FD, and a 12-bit 1 MSPS ADC with up to 16 channels. Extended Flash Performance (-EFP) variant increases Flash endurance to 100k cycles and improves retention for industrial and automotive-grade deployments.
The architecture integrates a 5-channel Direct Memory Access controller, Event System for hardware-triggered task chaining, and SERCOM peripherals configurable as UART, SPI, I2C, or LIN. The 14x14 TQFP-100 footprint provides ample GPIO for motor control, HMI, and multi-protocol gateway designs where pin count directly impacts board layout.
Typical applications include industrial IoT gateways, motor control (BLDC/PMSM FOC), building automation controllers, USB peripherals with Ethernet bridging, and human-machine interfaces with TFT displays. The combination of CAN-FD, Ethernet, and USB makes the device a strong fit for connected industrial nodes where deterministic communication is required.
When designing, ensure the trace impedance for USB and Ethernet is calculated per USB 2.0 and IEEE 802.3 specifications. The on-chip voltage regulator requires a 1uF X7R bypass capacitor close to VDDCORE; missing this capacitor results in unstable operation. Decouple each VDDIO group separately to minimize digital switching noise coupling into the analog ADC rails.
This page consolidates distributor pricing for the ATSAME54N19A-AU-EFP, drop-in compatible ATSAME5x family members, and engineering guidance not found in the manufacturer datasheet alone.
Alternatives de remplacement direct pour ATSAME54N19A-AU-EFP — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ATSAME54N19A-AU-EFP (même facteur de forme et même empreinte) — différant par USB, Operating Temperature, SRAM, Core Architecture, Core.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ATSAME54N19A-AU
✅ Remplacement direct✓ En stock
$5.42 / unité
Voir la fiche technique →ATSAME54N19A-AUT-EFP
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATSAME54P20A-AU-EFP
✅ Remplacement direct✓ En stock
$9.46 / unité
Voir la fiche technique →ATSAMD51N19A-AUT-EFP
✅ Remplacement direct✓ En stock
$3.65 / unité
Voir la fiche technique →ATSAME53N20A-AU-EFP
✅ Remplacement direct✓ En stock
$7.35 / unité
Voir la fiche technique →ATSAME53N20A-AU
✅ Remplacement direct✓ En stock
$10.3 / unité
Voir la fiche technique →ATSAME51N20A-AU-EFP
✅ Remplacement direct✓ En stock
$8.1 / unité
Voir la fiche technique →ATSAME54N19A-AU-EFP Valeurs maximales et caractéristiques électriques
| Core | ARM Cortex-M4F with FPU and DSP |
| Maximum Clock Speed | 120 MHz |
| Program Memory (Flash) | 512 KB dual-panel with ECC |
| SRAM | 192 KB with ECC |
| Operating Voltage | 2.7 V to 3.6 V |
| Boîtier | TQFP-100 (14x14 mm) |
| Type de montage | Surface Mount |
| Température de fonctionnement | -40C to +85C (industrial) |
| USB | USB 2.0 Full-Speed with integrated PHY |
| Ethernet | 10/100 Mbps MAC with IEEE 1588 |
| CAN | CAN-FD |
| ADC | 12-bit, 1 MSPS, up to 16 channels |
| SERCOM Peripherals | Up to 8 (UART/SPI/I2C/LIN configurable) |
| DMA Channels | 5 |
| Nombre de broches | 100 |
| Statut RoHS | Compliant |
| Niveau MSL | 3 (168 hours) |
Configuration des broches de ATSAME54N19A-AU-EFP
| Broche 1 | PA00 — GPIO/SERCOM1[0]/EIC[0] |
| Broche 2 | PA01 — GPIO/SERCOM1[1]/EIC[1] |
| Broche 3 | PA02 — GPIO/SERCOM1[2]/EIC[2] |
| Broche 4 | PA03 — GPIO/SERCOM1[3]/EIC[3] |
| Broche 5 | PA04 — GPIO/SERCOM0[0]/EIC[4] |
| Broche 6 | PA05 — GPIO/SERCOM0[1]/EIC[5] |
| Broche 7 | PA06 — GPIO/SERCOM0[2]/EIC[6] |
| Broche 8 | PA07 — GPIO/SERCOM0[3]/EIC[7] |
| Broche 9 | VDDIO — I/O supply voltage |
| Broche 10 | VDDIN — Main supply voltage input |
| Broche 11 | GND — Ground |
| Broche 12 | PA08 — GPIO/SERCOM2[0]/EIC[8]/NMI |
| Broche 13 | PA09 — GPIO/SERCOM2[1]/EIC[9] |
| Broche 14 | PA10 — GPIO/SERCOM2[2]/EIC[10] |
| Broche 15 | VDDCORE — Core voltage output (regulator) |
| Broche 16 | GND — Ground |
| Broche 17 | VDDIO — I/O supply voltage |
| Broche 18 | PA11 — GPIO/SERCOM2[3]/EIC[11] |
| Broche 19 | PA12 — GPIO/SERCOM4[0]/EIC[12] |
| Broche 20 | PA13 — GPIO/SERCOM4[1]/EIC[13] |
| Broche 21 | PA14 — GPIO/SERCOM4[2]/EIC[14] |
| Broche 22 | PA15 — GPIO/SERCOM4[3]/EIC[15] |
| Broche 23 | PA16 — GPIO/SERCOM1[0]/EIC[0] |
| Broche 24 | PA17 — GPIO/SERCOM1[1]/EIC[1] |
| Broche 25 | PA18 — GPIO/SERCOM1[2]/EIC[2]/XIN |
| Broche 26 | PA19 — GPIO/SERCOM1[3]/EIC[3]/XOUT |
| Broche 27 | PA20 — GPIO/SERCOM5[2]/TC[0] |
| Broche 28 | PA21 — GPIO/SERCOM5[3]/TC[1] |
| Broche 29 | PA22 — GPIO/SERCOM3[0]/TC[2] |
| Broche 30 | PA23 — GPIO/SERCOM3[1]/TC[3] |
| Broche 31 | VDDANA — Analog supply voltage |
| Broche 32 | GNDANA — Analog ground |
| Broche 33 | PA24 — GPIO/SERCOM3[2]/TC[4] |
| Broche 34 | PA25 — GPIO/SERCOM3[3]/TC[5] |
| Broche 35 | VDDIO — I/O supply voltage |
| Broche 36 | GND — Ground |
| Broche 37 | PB00 — GPIO/SERCOM5[0]/EIC[0] |
| Broche 38 | PB01 — GPIO/SERCOM5[1]/EIC[1] |
| Broche 39 | PB02 — GPIO/SERCOM5[2]/EIC[2] |
| Broche 40 | PB03 — GPIO/SERCOM5[3]/EIC[3] |
| Broche 41 | PB04 — GPIO/SERCOM7[0]/EIC[4] |
| Broche 42 | PB05 — GPIO/SERCOM7[1]/EIC[5] |
| Broche 43 | PB06 — GPIO/SERCOM7[2]/EIC[6] |
| Broche 44 | PB07 — GPIO/SERCOM7[3]/EIC[7] |
| Broche 45 | PB08 — GPIO/SERCOM4[0]/EIC[8] |
| Broche 46 | PB09 — GPIO/SERCOM4[1]/EIC[9] |
| Broche 47 | PB10 — GPIO/SERCOM4[2]/EIC[10] |
| Broche 48 | PB11 — GPIO/SERCOM4[3]/EIC[11] |
| Broche 49 | PB12 — GPIO/SERCOM4[0]/TC[0] |
| Broche 50 | PB13 — GPIO/SERCOM4[1]/TC[1] |
| Broche 51 | PB14 — GPIO/SERCOM4[2]/TC[2] |
| Broche 52 | PB15 — GPIO/SERCOM4[3]/TC[3] |
| Broche 53 | VDDIO — I/O supply voltage |
| Broche 54 | GND — Ground |
| Broche 55 | PB16 — GPIO/SERCOM5[0]/TC[4] |
| Broche 56 | PB17 — GPIO/SERCOM5[1]/TC[5] |
| Broche 57 | PB18 — GPIO/SERCOM5[2]/TC[6] |
| Broche 58 | PB19 — GPIO/SERCOM5[3]/TC[7] |
| Broche 59 | PB20 — GPIO/SERCOM3[0]/TC[8] |
| Broche 60 | PB21 — GPIO/SERCOM3[1]/TC[9] |
| Broche 61 | PB22 — GPIO/SERCOM3[2]/TC[10] |
| Broche 62 | PB23 — GPIO/SERCOM3[3]/TC[11] |
| Broche 63 | PB24 — GPIO/SERCOM0[0]/TC[2] |
| Broche 64 | PB25 — GPIO/SERCOM0[1]/TC[3] |
| Broche 65 | PB26 — GPIO/SERCOM0[2]/TC[4] |
| Broche 66 | PB27 — GPIO/SERCOM0[3]/TC[5] |
| Broche 67 | PB28 — GPIO/SERCOM2[0]/TC[6] |
| Broche 68 | PB29 — GPIO/SERCOM2[1]/TC[7] |
| Broche 69 | PB30 — GPIO/SERCOM2[2]/TC[8] |
| Broche 70 | PB31 — GPIO/SERCOM2[3]/TC[9] |
| Broche 71 | VDDIO — I/O supply voltage |
| Broche 72 | GND — Ground |
| Broche 73 | PC00 — GPIO/SERCOM6[0]/EIC[0] |
| Broche 74 | PC01 — GPIO/SERCOM6[1]/EIC[1] |
| Broche 75 | PC02 — GPIO/SERCOM6[2]/EIC[2] |
| Broche 76 | PC03 — GPIO/SERCOM6[3]/EIC[3] |
| Broche 77 | PC04 — GPIO/SERCOM7[0]/EIC[4] |
| Broche 78 | PC05 — GPIO/SERCOM7[1]/EIC[5] |
| Broche 79 | PC06 — GPIO/SERCOM7[2]/EIC[6] |
| Broche 80 | PC07 — GPIO/SERCOM7[3]/EIC[7] |
| Broche 81 | PC08 — GPIO/SERCOM6[0]/TC[0] |
| Broche 82 | PC09 — GPIO/SERCOM6[1]/TC[1] |
| Broche 83 | PC10 — GPIO/SERCOM6[2]/TC[2] |
| Broche 84 | PC11 — GPIO/SERCOM6[3]/TC[3] |
| Broche 85 | PC12 — GPIO/SERCOM7[0]/TC[4] |
| Broche 86 | PC13 — GPIO/SERCOM7[1]/TC[5] |
| Broche 87 | PC14 — GPIO/SERCOM7[2]/TC[6] |
| Broche 88 | PC15 — GPIO/SERCOM7[3]/TC[7] |
| Broche 89 | VDDIO — I/O supply voltage |
| Broche 90 | GND — Ground |
| Broche 91 | PD00 — GPIO/SERCOM3[0]/TC[0] |
| Broche 92 | PD01 — GPIO/SERCOM3[1]/TC[1] |
| Broche 93 | PD02 — GPIO/SERCOM3[2]/TC[2] |
| Broche 94 | PD03 — GPIO/SERCOM3[3]/TC[3] |
| Broche 95 | PD04 — GPIO/SERCOM4[0]/TC[4] |
| Broche 96 | PD05 — GPIO/SERCOM4[1]/TC[5] |
| Broche 97 | PD06 — GPIO/SERCOM4[2]/TC[6] |
| Broche 98 | PD07 — GPIO/SERCOM4[3]/TC[7] |
| Broche 99 | PD08 — GPIO/SERCOM7[0]/TC[8] |
| Broche 100 | PD09 — GPIO/SERCOM7[1]/TC[9] |
Applications typiques
ATSAME54N19A-AU-EFP convient pour 6 applications: Industrial IoT Gateway, BLDC / PMSM Motor Control (FOC), Building Automation Controller, USB Peripherals with Ethernet Bridging, Human-Machine Interface (HMI) with TFT Display, Connected Sensor Node (Industrial).
Industrial IoT Gateway
The ATSAME54N19A-AU-EFP's combination of 10/100 Mbps Ethernet MAC with IEEE 1588 timestamping, CAN-FD bus interface, and full-speed USB with integrated PHY makes it ideal for industrial IoT gateway designs. The 120 MHz Cortex-M4F core handles protocol translation between fieldbus and Ethernet while the dual-panel 512 KB Flash with ECC enables fail-safe OTA firmware upgrades. Place the device between a LAN8720A Ethernet PHY on RMII pins and a CAN-FD transceiver on the CAN pins. Compared to a discrete MCU+ASIC approach, the integrated MAC and USB PHY save 15-20 mm^2 of PCB area. Per Microchip AN2339, this architecture supports EtherCAT, PROFINET, and Modbus TCP slave stacks.
Recommandé
BLDC / PMSM Motor Control (FOC)
The ATSAME54N19A-AU-EFP is well suited for sensorless BLDC and PMSM Field-Oriented Control (FOC) thanks to its 120 MHz Cortex-M4F core with DSP extensions and hardware PWM timers with complementary outputs and dead-band insertion. The 1 MSPS 12-bit ADC enables simultaneous sampling of three-phase currents for accurate FOC. According to Microchip AN3349, the SAM E54 family runs FOC loops under 5 kHz with margin for sensored control. The 100-pin TQFP provides sufficient I/O for three complementary PWM pairs, three current-sense ADCs, Hall/encoder inputs, and UART debug. Pair with MCP8021 or DRV8313 gate driver for a complete 3-phase motor drive.
Recommandé
Building Automation Controller
The ATSAME54N19A-AU-EFP is a strong fit for building automation controllers because it integrates Ethernet, CAN-FD, USB, and up to eight SERCOM channels (UART/SPI/I2C/LIN) for connecting to HVAC actuators, lighting buses (DALI), and sensor networks. The 192 KB SRAM with ECC handles BACnet/Modbus/TCP stack plus real-time scheduler without external memory. Its industrial -40C to +85C rating covers unheated electrical rooms. Place the MCU on a 4-layer PCB with separate analog/digital grounds for ADC noise immunity. Per Microchip AN3429, the SAM E54 family supports KNX, BACnet, and LonWorks through external transceivers.
Recommandé
USB Peripherals with Ethernet Bridging
The ATSAME54N19A-AU-EFP's integrated full-speed USB 2.0 PHY and 10/100 Mbps Ethernet MAC allow it to bridge USB devices to Ethernet networks without an external hub IC. This is ideal for USB-over-IP servers, isolated USB diagnostic interfaces, and USB printer servers. The 120 MHz core handles TCP/IP stack on the Ethernet side while maintaining USB bulk transfers, with DMA moving data between peripherals without CPU overhead. Per Microchip AN3133, the SAM E54 family achieves sustained USB full-speed throughput (1 MB/s) while simultaneously servicing Ethernet traffic.
Recommandé
Human-Machine Interface (HMI) with TFT Display
The ATSAME54N19A-AU-EFP's 120 MHz core and 192 KB SRAM support SPI/parallel TFT displays up to 320x240 resolution with hardware-accelerated graphics primitives. The eight SERCOM channels can interface a touch controller (I2C), external Flash (SPI), and UART debug while driving the display. Per Microchip AN2937, the SAM E54 family implements LVGL graphics library at 30+ FPS on 320x240 screens. The 100-pin TQFP provides the GPIO count needed for parallel RGB interfaces when higher refresh rates are required.
Recommandé
Connected Sensor Node (Industrial)
The ATSAME54N19A-AU-EFP supports connected industrial sensor nodes by combining Ethernet, CAN-FD, and USB with the 1 MSPS 12-bit ADC for multi-channel analog acquisition. The SERCOM peripherals handle UART sensors (Modbus RTU), SPI sensors, and I2C sensors in parallel. The -40C to +85C industrial rating and -EFP Flash endurance (100k cycles, 20-year retention) make this part suitable for long-life industrial installations where reliability outweighs BOM cost. Per Microchip AN2524, the SAM E54 family's Event System enables hardware-triggered ADC sampling without CPU wake-up, reducing quiescent power.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ATSAME54N19A-AU-EFP — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ATSAME54N19A-AU | ATSAME54N19A-AUT-EFP | ATSAME54P20A-AU-EFP | ATSAMD51N19A-AUT-EFP | ATSAME53N20A-AU-EFP |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-100 (14x14) | TQFP-100 (14x14) | TQFP-100 (14x14) | TQFP-100 (14x14) | TQFP-100 (14x14) | TQFP-100 (14x14) |
| Core Clock | 120 MHz | 120 MHz | 120 MHz | 120 MHz | 120 MHz | 120 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 1024 KB | 512 KB | 1024 KB |
| SRAM | 192 KB | 192 KB | 192 KB | 256 KB | 192 KB | 256 KB |
| Flash Endurance (-EFP) | 100k cycles | 10k cycles | 100k cycles | 100k cycles | 100k cycles | 100k cycles |
| Ethernet MAC | Yes (10/100 with 1588) | Yes (10/100 with 1588) | Yes (10/100 with 1588) | Yes (10/100 with 1588) | No | No |
| CAN-FD | Yes | Yes | Yes | Yes | No | No |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +125C (AEC-Q100) | -40C to +85C |
Principaux différenciateurs
- Extended Flash Performance (100k cycles, 20-year retention) (vs ATSAME54N19A-AU)
- Includes Ethernet MAC and CAN-FD (vs ATSAME53N20A-AU-EFP)
- Industrial grade vs automotive grade (vs ATSAMD51N19A-AUT-EFP)
Notes de conception
The ATSAME54N19A-AU-EFP integrates a 1.2V LDO regulator on VDDCORE (pin 15). Per SAM E54 family datasheet, place a 1uF X7R 6.3V ceramic capacitor within 5 mm of pin 15 with short traces to GND (pin 16). Omitting or misplacing this capacitor causes VDDCORE ripple that manifests as erratic Flash programming failures, ADC drift, or core lockup. VDDIN (pin 10) requires 1uF + 100 nF decoupling; VDDANA (pin 31) needs a ferrite bead from VDDIO plus a separate 100 nF capacitor to GNDANA (pin 32).
Route the 50 MHz RMII signals between the ATSAME54N19A-AU-EFP and the external LAN8720A PHY with controlled impedance (50 ohm single-ended) and matched trace lengths within 50 mil. Keep RMII traces away from PWM switching nodes and the on-chip switching regulator to avoid coupling noise into the MAC. Per Microchip AN2100, a 4-layer PCB with dedicated analog and digital ground planes is mandatory; splitting grounds under the MCU is not recommended.
Three common pitfalls when bringing up ATSAME54N19A-AU-EFP designs: (1) forgetting to program the GCLK_MAIN divisor from the 48 MHz DFLL to the desired CPU clock causes NMI lockup; (2) leaving SWDIO/SWDCLK floating during POR can place the device in a debug-wait state - add 100 kohm pull-up to SWDIO per the SAM E54 family datasheet; (3) using the DAC without enabling the VDDANA reference buffer results in code-loaded rather than buffered output. Always run the Atmel Studio/MPLAB X project's start-up files before evaluating peripherals.
For USB full-speed operation, the ATSAME54N19A-AU-EFP's integrated PHY requires 45 ohm differential impedance on D+/D-. Per USB 2.0 specification, route the differential pair with no more than 50 mil mismatch and keep total length under 50 mm. Place the 27 ohm series termination resistors within 4 mm of the MCU pads. Without proper impedance control, USB enumeration fails at high temperature.
Informations de conformité
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified - choose ATSAMD51N19A-AUT-EFP for automotive. Halogen-free per Microchip environmental compliance statement.
