ATSAME54N20A-AUT - 120MHz ARM Cortex-M4F MCU, 1MB Flash | Microchip
Référence : ATSAME54N20A-AUT ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $11.86 | $11,86 |
| 10 | $10.78 | $107,80 |
| 100 | $9.4 | $940,00 |
| 500 | $8.55 | $4 275,00 |
| 1 000 | $7.85 | $7 850,00 |
| 3 000 | $7.1 | $21 300,00 |
ATSAME54N20A-AUT Présentation
What is an ARM Cortex-M4F microcontroller? It is a 32-bit microcontroller core based on the ARMv7-M architecture with hardware single-precision floating point, DSP extensions, and a Nested Vectored Interrupt Controller (NVIC). In the power-management IC hierarchy, this device sits at the high-performance MCU tier used for digital control loops, communication stacks, and sensor fusion. The SAM E54 family adds peripheral integration such as 10/100 Ethernet MAC, CAN-FD, and high-speed USB, which makes it a step above general-purpose Cortex-M0/M3 designs.
Key features of the ATSAME54N20A-AUT include up to 120 MHz core clock, 1 MB of Flash with Error Correction Code (ECC), 256 KB SRAM with ECC, a 12-bit 1 Msps ADC, a 12-bit DAC, two CAN-FD controllers, a 10/100 Mbps Ethernet MAC, full-speed and high-speed USB 2.0 with on-chip PHY, and a QSPI/SPI interface supporting external memory. The dual-panel Flash supports simultaneous read-while-write operation, enabling live firmware updates without stalling the CPU.
The Cortex-M4F core delivers 1.25 DMIPS/MHz with hardware FPU and DSP saturating arithmetic, allowing high-speed fixed- and floating-point math. The peripheral event system and Direct Memory Access Controller (DMAC) offload repetitive I/O and data-movement tasks from the CPU, leaving headroom for control algorithms and protocol stacks running concurrently.
Typical applications include industrial automation controllers, automotive body and gateway ECUs, building automation gateways with Ethernet or CAN-FD, IoT edge nodes with TLS acceleration, and graphical HMI panels driving TFT LCDs. The combination of CAN-FD, Ethernet, and USB also suits connected equipment that must bridge fieldbus and IP networks.
When designing with this part, allocate the QSPI footprint even if unused, because PCB rework is easier than spinning the board. Always add a 32.768 kHz crystal and 12 MHz crystal because Ethernet and USB PHYs require precise timing references for compliance.
This page synthesizes distributor pricing, drop-in alternatives from the SAM E54 family, and practical design notes that are not present in the manufacturer datasheet alone.
Alternatives de remplacement direct pour ATSAME54N20A-AUT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ATSAME54N20A-AUT (même facteur de forme et même empreinte) — différant par USB, ADC, Package, SRAM, Core.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ATSAME54N20A-AU-EFP
✅ Remplacement direct✓ En stock
$8.1 / unité
Voir la fiche technique →ATSAME54N19A-AUT
✅ Remplacement direct✓ En stock
$5.94 / unité
Voir la fiche technique →ATSAME54N19A-AU-EFP
✅ Remplacement direct✓ En stock
$7.28 / unité
Voir la fiche technique →ATSAME53N20A-AU-EFP
✅ Remplacement direct✓ En stock
$7.35 / unité
Voir la fiche technique →ATSAME53N20A-AU
✅ Remplacement direct✓ En stock
$10.3 / unité
Voir la fiche technique →ATSAME51N20A-AUT-EFP
✅ Remplacement direct✓ En stock
$5.65 / unité
Voir la fiche technique →ATSAME54N20A-AUT Valeurs maximales et caractéristiques électriques
| Core Architecture | ARM Cortex-M4F (32-bit) |
| Maximum CPU Clock | 120 MHz |
| FPU | Single-precision hardware Floating Point Unit |
| Program Flash | 1 MB (Dual-Panel, with ECC) |
| SRAM | 256 KB (with ECC) |
| Operating Voltage (VDDIO) | 1.71 V to 3.6 V |
| Température de fonctionnement | -40 C to +85 C (automotive grade) |
| Boîtier | 100-pin TQFP (14x14 mm) |
| ADC | 12-bit, up to 1 Msps |
| DAC | 12-bit |
| CAN-FD Controllers | 2 |
| Ethernet MAC | 10/100 Mbps |
| USB | Full-Speed + High-Speed USB 2.0 with on-chip PHY |
| External Memory Bus | QSPI/SPI (for external Flash/PSRAM) |
| DMA | Yes (DMAC) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
Configuration des broches de ATSAME54N20A-AUT
| Broche 1 | PA03 — GPIO / ADC AIN1 |
| Broche 2 | PA04 — GPIO / ADC AIN4 |
| Broche 3 | PA05 — GPIO / ADC AIN5 |
| Broche 4 | PA06 — GPIO / ADC AIN6 |
| Broche 5 | PA07 — GPIO / ADC AIN7 |
| Broche 6 | PA08 — GPIO / SERCOM0 PAD0 |
| Broche 7 | PA09 — GPIO / SERCOM0 PAD1 |
| Broche 8 | PA10 — GPIO / SERCOM0 PAD2 |
| Broche 9 | PA11 — GPIO / SERCOM0 PAD3 |
| Broche 10 | VDDIO — I/O supply voltage |
| Broche 11 | VSS — Ground |
| Broche 12 | PA12 — GPIO / SERCOM2 PAD0 |
| Broche 13 | PA13 — GPIO / SERCOM2 PAD1 |
| Broche 14 | PA14 — GPIO / SERCOM2 PAD2 |
| Broche 15 | PA15 — GPIO / SERCOM2 PAD3 |
| Broche 16 | PA16 — GPIO / SERCOM1 PAD0 |
| Broche 17 | PA17 — GPIO / SERCOM1 PAD1 |
| Broche 18 | PA18 — GPIO / SERCOM1 PAD2 |
| Broche 19 | PA19 — GPIO / SERCOM1 PAD3 |
| Broche 20 | PA20 — GPIO / SERCOM3 PAD0 |
| Broche 21 | PA21 — GPIO / SERCOM3 PAD1 |
| Broche 22 | PA22 — GPIO / SERCOM3 PAD2 |
| Broche 23 | PA23 — GPIO / SERCOM3 PAD3 |
| Broche 24 | PA24 — GPIO / USB D- |
| Broche 25 | PA25 — GPIO / USB D+ |
| Broche 26 | PB00 — GPIO |
| Broche 27 | PB01 — GPIO |
| Broche 28 | PB02 — GPIO / ADC AIN14 |
| Broche 29 | PB03 — GPIO / ADC AIN15 |
| Broche 30 | PB04 — GPIO |
| Broche 31 | PB05 — GPIO |
| Broche 32 | PB06 — GPIO |
| Broche 33 | PB07 — GPIO |
| Broche 34 | PB08 — GPIO |
| Broche 35 | PB09 — GPIO |
| Broche 36 | PB10 — GPIO |
| Broche 37 | PB11 — GPIO |
| Broche 38 | PB12 — GPIO |
| Broche 39 | PB13 — GPIO |
| Broche 40 | PB14 — GPIO |
| Broche 41 | PB15 — GPIO |
| Broche 42 | PC00 — GPIO |
| Broche 43 | PC01 — GPIO |
| Broche 44 | PC02 — GPIO |
| Broche 45 | PC03 — GPIO |
| Broche 46 | VDDIO — I/O supply voltage |
| Broche 47 | VSS — Ground |
| Broche 48 | PC04 — GPIO |
| Broche 49 | PC05 — GPIO |
| Broche 50 | PC06 — GPIO |
| Broche 51 | PC07 — GPIO |
| Broche 52 | PC08 — GPIO |
| Broche 53 | PC09 — GPIO |
| Broche 54 | PC10 — GPIO |
| Broche 55 | PC11 — GPIO |
| Broche 56 | PC12 — GPIO |
| Broche 57 | PC13 — GPIO |
| Broche 58 | PC14 — GPIO |
| Broche 59 | PC15 — GPIO |
| Broche 60 | PC16 — GPIO |
| Broche 61 | PC17 — GPIO |
| Broche 62 | PC18 — GPIO |
| Broche 63 | PC19 — GPIO |
| Broche 64 | PC20 — GPIO |
| Broche 65 | PC21 — GPIO |
| Broche 66 | PC22 — GPIO |
| Broche 67 | PC23 — GPIO |
| Broche 68 | PC24 — GPIO |
| Broche 69 | PC25 — GPIO |
| Broche 70 | PC26 — GPIO |
| Broche 71 | PC27 — GPIO |
| Broche 72 | PC28 — GPIO |
| Broche 73 | PC29 — GPIO |
| Broche 74 | PD00 — GPIO |
| Broche 75 | PD01 — GPIO |
| Broche 76 | PD02 — GPIO |
| Broche 77 | PD03 — GPIO |
| Broche 78 | PD04 — GPIO |
| Broche 79 | PD05 — GPIO |
| Broche 80 | PD06 — GPIO |
| Broche 81 | PD07 — GPIO |
| Broche 82 | PD08 — GPIO |
| Broche 83 | PD09 — GPIO |
| Broche 84 | PD10 — GPIO |
| Broche 85 | PD11 — GPIO |
| Broche 86 | PD12 — GPIO |
| Broche 87 | VDDCORE — Core supply (decoupling cap) |
| Broche 88 | VSS — Ground |
| Broche 89 | VDDIO — I/O supply voltage |
| Broche 90 | VSS — Ground |
| Broche 91 | XIN32 — 32.768 kHz crystal input |
| Broche 92 | XOUT32 — 32.768 kHz crystal output |
| Broche 93 | XIN — 12 MHz main crystal input |
| Broche 94 | XOUT — 12 MHz main crystal output |
| Broche 95 | NRST — Reset input, active low |
| Broche 96 | SWDIO — Serial Wire Debug I/O |
| Broche 97 | SWCLK — Serial Wire Debug clock |
| Broche 98 | VBUS — USB VBUS detect |
| Broche 99 | VDDIO — I/O supply voltage |
| Broche 100 | VSS — Ground |
Applications typiques
ATSAME54N20A-AUT convient pour 6 applications: Automotive Gateway ECU, Industrial Automation Controller, Building Automation Gateway, IoT Edge Sensor Hub, Connected Medical Instrument, Graphical HMI Panel Controller.
Automotive Gateway ECU
The ATSAME54N20A-AUT fits automotive gateway ECUs because it integrates two CAN-FD controllers, a 10/100 Ethernet MAC, and USB 2.0 High-Speed with on-chip PHY in a single -AUT qualified package. With 1 MB Dual-Panel Flash, the firmware can hold a Secure Onboard Communication (SecOC) stack plus a CAN-to-Ethernet translation layer simultaneously, while the ECC on Flash and SRAM guards against soft errors in the noisy underhood environment. The Cortex-M4F FPU accelerates AUTOSAR-style signal-processing tasks and TLS handshakes for diagnostic over IP (DoIP). Place a 100BASE-TX transformer and RJ45 jack plus a 12 MHz crystal to complete the Ethernet PHY reference clock, and route CAN-FD lines with 120-ohm termination to meet ISO 11898-1 compliance.
Recommandé
Industrial Automation Controller
In industrial PLC and motion-controller blocks, the ATSAME54N20A-AUT delivers 120 MHz Cortex-M4F performance with hardware FPU and DSP extensions, enough to run a real-time control loop on a multi-axis servo drive while leaving headroom for EtherNet/IP or Modbus TCP on the integrated 10/100 Ethernet MAC. The 12-bit 1 Msps ADC supports current and voltage sensing for closed-loop vector control, while the dual-panel Flash supports field firmware updates without shutting down the line. The 100-pin TQFP footprint exposes all SERCOM channels, so RS-485 and RS-232 transceivers can be added without bus mux logic. Operate the part within -40 C to +85 C ambient and provide a 32.768 kHz RTC crystal for timestamping process events.
Recommandé
Building Automation Gateway
The ATSAME54N20A-AUT is well suited to BACnet or KNX-to-IP gateways used in commercial buildings because the Cortex-M4F core can parse BACnet/IP frames, encrypt them with TLS, and forward them over Ethernet concurrently. The on-chip USB 2.0 High-Speed PHY simplifies commissioning via a temporary laptop tether for firmware updates. The 1 MB Dual-Panel Flash stores both the application image and a fallback image for OTA rollbacks, while the 256 KB ECC SRAM caches BACnet object lists without exhausting the bus bandwidth. A 12 MHz main crystal plus a 32.768 kHz watch crystal are required for the Ethernet PHY reference clock and the RTC respectively; without these, link-up will fail.
Recommandé
IoT Edge Sensor Hub
Edge sensor hubs aggregate analog and digital sensors and publish to a cloud broker. The ATSAME54N20A-AUT integrates a 12-bit 1 Msps ADC and a 12-bit DAC, plus SERCOM channels for I2C and SPI sensor chains, removing the need for an external ADC. The Ethernet MAC or USB 2.0 High-Speed PHY provides the uplink, while the Cortex-M4F FPU runs a TFLite Micro inference model for anomaly detection on vibration or acoustic streams. The Dual-Panel Flash supports signed OTA updates with rollback, and the ECC SRAM guards single-bit errors in long-lived edge deployments. Total power consumption at 120 MHz with all peripherals enabled is below 100 mW at 3.3 V, well within solar or battery-backed budgets.
Recommandé
Connected Medical Instrument
Connected medical instruments such as portable patient monitors benefit from the ATSAME54N20A-AUT because the Cortex-M4F FPU accelerates DSP filter chains for ECG and pulse-oximetry signal conditioning. The 12-bit 1 Msps ADC samples multiple physiological channels, while the integrated Ethernet MAC provides isolated wired connectivity to the central monitoring station, avoiding the need for an external PHY that could leak ground noise. ECC on Flash and SRAM is critical for medical data integrity, and the automotive temperature grade gives extra margin in warm clinical environments. Designers should add a watchdog timer and brown-out detector; both are integrated in the SAM E54 power manager.
Recommandé
Graphical HMI Panel Controller
The ATSAME54N20A-AUT can drive TFT LCD HMI panels up to WVGA via the integrated EBI and QSPI interfaces, while the Cortex-M4F handles touch event processing and UI rendering. The 100-pin TQFP package exposes the parallel EBI bus plus the 12-bit DAC for backlight PWM, eliminating the need for an external graphics controller on mid-size panels. The USB 2.0 High-Speed PHY provides a fast configuration and log-dump channel during factory test. Plan for at least 256 KB of external PSRAM when targeting WVGA because the internal 256 KB SRAM is consumed by frame buffers and the LVGL stack. A 12 MHz crystal plus a 32.768 kHz RTC crystal are required for stable USB and Ethernet timing.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ATSAME54N20A-AUT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ATSAME54N20A-AU-EFP | ATSAME54N19A-AUT | ATSAME54N19A-AU-EFP | ATSAME53N20A-AU-EFP | ATSAME51N20A-AUT-EFP |
|---|---|---|---|---|---|---|
| Package | 100-TQFP (14x14 mm) | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz |
| Flash | 1 MB Dual-Panel ECC | 1 MB Dual-Panel ECC | 512 KB Dual-Panel ECC | 512 KB Dual-Panel ECC | 1 MB Dual-Panel ECC | 1 MB Dual-Panel ECC |
| SRAM | 256 KB ECC | 256 KB ECC | 192 KB ECC | 192 KB ECC | 256 KB ECC | 256 KB ECC |
| Ethernet MAC | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | Not present | Not present |
| CAN-FD Controllers | 2 | 2 | 2 | 2 | 2 | 0 (CAN 2.0B only) |
| USB | FS + HS USB 2.0 PHY | FS + HS USB 2.0 PHY | FS + HS USB 2.0 PHY | FS + HS USB 2.0 PHY | FS + HS USB 2.0 PHY | FS USB only |
| Operating Temperature | -40 C to +85 C (Automotive) | -40 C to +85 C (Industrial) | -40 C to +85 C (Automotive) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Automotive) |
Principaux différenciateurs
- Dual-panel Flash with ECC enables live firmware update (vs ATSAME54N19A-AUT)
- Automotive -40 C to +85 C grade qualification (vs ATSAME54N20A-AU-EFP)
- Integrated 10/100 Ethernet MAC eliminates external PHY control logic (vs ATSAME53N20A-AU-EFP)
- Two CAN-FD controllers support modern automotive network topologies (vs ATSAME51N20A-AUT-EFP)
Notes de conception
The ATSAME54N20A-AUT requires three separate supply rails: VDDIO at 3.3 V, VDDCORE at 1.2 V (regulated internally by the on-chip LDO from VDDIO), and VDDPLL for the USB PLL at 3.3 V. Place a 100 nF decoupling cap on every VDDIO/VSS pair within 3 mm of the pin, and add a bulk 10 uF ceramic on the VDDIO rail close to pin 46/89. The internal 1.2 V LDO requires at least 1 uF of output capacitance on VDDCORE (pin 87) to maintain stability under 120 MHz load transients. Inadequate decoupling is the most common cause of USB enumeration failure and Ethernet CRC errors.
At 120 MHz with all peripherals enabled, the ATSAME54N20A-AUT dissipates approximately 120 mW from a 3.3 V supply. Estimated: using 120 MHz x 1.0 mA/MHz typical core current from the datasheet DC characteristics, plus 20 mA for active peripherals, total current draw is roughly 140 mA at 3.3 V. The 100-pin TQFP package has theta_JA around 45 C/W on a 4-layer JEDEC test board, which keeps junction temperature rise under 6 C above ambient - no heatsink needed. However, if the design confines the part to a 2-layer board with limited ground copper, theta_JA can exceed 70 C/W, and the junction temperature must be recalculated using the actual board thermal resistance.
Route the Ethernet RMII signals (PA12-PA17, PC10, PC11) as a matched-length group with 50-ohm characteristic impedance and maximum 50 mm length. Keep them away from switching power lines and the crystal traces. The USB 2.0 D+/D- differential pair (PA24, PA25) must be routed with 90-ohm differential impedance and matched to within 150 mil. Place the 12 MHz crystal (XIN/XOUT) within 5 mm of pins 93/94 with a guard ring tied to ground, and do not route any signal traces under the crystal or its capacitors.
Do not populate the 32.768 kHz crystal with a 6 pF load-capacitor rating if the actual crystal spec calls for 12.5 pF - this is a frequent cause of RTC drift and Ethernet PHY link-up failures. Always check the crystal datasheet's load capacitance and use the formula C_L = (C1 x C2) / (C1 + C2) + C_stray to size the caps. Also remember that the SAM E54 requires the NVM user row to be programmed with the correct FPLL and DPLL settings, or the part will run at the reset-default 4 MHz internal oscillator instead of 120 MHz.
Informations de conformité
AEC-Q100 grade 1 implied by -AUT suffix per Microchip ordering information. RoHS and REACH compliance per Microchip product page.
