ISL8487IB-T - Low-Power RS-485/422 Transceiver | Renesas
Référence : ISL8487IB-T ✓ ActifISL8487IB-T Présentation
An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level transmit and receive signals into differential bus signals and converts incoming differential signals into CMOS-compatible logic. The RS-485 standard supports balanced, multipoint communication over relatively long cables, while RS-422 is commonly used for point-to-point links. Within the interface hierarchy, the ISL8487IB-T belongs to the RS-485/RS-422 transceiver class of communication interface ICs.
The device is identified as a one-transceiver, half-duplex component with one-quarter unit-load drive capability. Its 5 V operation and low-power design make it appropriate for embedded systems in which every milliampere affects system thermal performance or battery life. The 8-pin SOIC package also supports compact, surface-mount PCB construction while providing enough pins for separate driver input, receiver output, enable control, supply, and ground connections.
The one-quarter unit-load rating enables the device to present only one quarter of a standard unit load to the bus. This loading capability allows more nodes to share a multidrop network than a one-unit-load transceiver while preserving signal integrity. Its half-duplex architecture supports shared transmit and receive circuitry, reducing board area and simplifying bus direction control in designs that do not require simultaneous full-duplex operation.
Typical uses include industrial sensor gateways, programmable logic controller communication, building automation, remote I/O modules, instrumentation, and embedded serial controllers. The part is particularly appropriate when the bus cable length, node count, ground-reference conditions, and data rate remain compatible with the limits of the Renesas ISL8487 family. A network should still be checked for termination, biasing, and transient protection requirements.
PCB implementation should keep the transceiver close to the bus connector and provide a continuous ground reference between the transceiver and connector. Place network termination and any failsafe biasing components where they can be selectively configured, and confirm that the logic interface voltage of the connected controller is compatible with the transceiver. The SOIC footprint simplifies assembly, although exposed bus and logic pins still require careful handling during soldering.
This product page combines package and interface details, commercially focused sourcing guidance, pin-compatible candidate evaluation, and application-specific design guidance. It is intended to help engineers verify the electrical trade-offs and board-level requirements before integrating the ISL8487IB-T into an RS-485 or RS-422 system.
Alternatives de remplacement direct pour ISL8487IB-T — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ISL8487IB-T (même facteur de forme et même empreinte) — différant par Package, Slew Rate, Mounting Type, Product Type, Supported Standards.
ISL8488IP
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →ISL8489E
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL8489EIB
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →ISL8489IB
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX483ECSA+T
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL8487IB-T Spécifications
| Transceiver Configuration | 1/1 Transceiver Half |
| Supported Standards | RS-422 and RS-485 |
| Tension d'alimentation | 5 V |
| Bus Unit Load | 1/4 Unit Load |
| Communication Mode | Half Duplex |
| ESD Protection | ESD Protected |
| Power Class | Low Power |
| Slew Rate | High Speed or Slew Rate Limited |
| Boîtier | 8-SOIC, 0.154 in (3.90 mm) Width |
| Type de montage | Surface Mount |
| Nombre de broches | 8 Pins |
| Manufacturer | Renesas Electronics Corporation |
Guide de configuration des broches du ISL8487IB-T 8-soic, 0.154 in (3.90 mm) width
Configuration des broches du ISL8487IB-T (boîtier 8-soic, 0.154 in (3.90 mm) width). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour ISL8487IB-T.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ISL8487IB-T convient pour 6 applications: Industrial Sensor Gateway, PLC Communication Module, Building Automation Controller, Remote I/O Module, Test and Measurement Instrument, Embedded Serial Controller.
Industrial Sensor Gateway
The ISL8487IB-T fits an industrial sensor gateway that must connect several remote sensor nodes to a controller over an RS-485 bus. Its one-quarter unit-load capability allows a higher node count than a one-unit-load transceiver, while the low-power 5 V operation reduces supply demand in distributed equipment. The half-duplex arrangement uses one physical bus for command transmission and sensor responses. Designers should place the transceiver near the bus connector, provide a continuous ground path, and verify termination and failsafe biasing for the actual cable length and topology.
Recommandé
PLC Communication Module
The ISL8487IB-T is appropriate for a programmable logic controller communication module that exchanges commands and process data with remote equipment over a balanced bus. Its 5 V operation supports compact controller boards, and the one-quarter unit-load rating helps preserve bus loading margin when several modules are connected. Half-duplex operation simplifies the physical interface, but firmware must control direction switching and account for turnaround time. Validate receive thresholds and bus timing against the network's data rate and termination arrangement before releasing the circuit.
Recommandé
Building Automation Controller
A building automation controller can use the ISL8487IB-T to connect thermostats, access panels, lighting controllers, and environmental sensors through an RS-485 network. Low power is useful in remotely powered or thermally constrained control cabinets, while the one-quarter unit-load interface supports a larger collection of bus nodes. The 8-pin SOIC keeps the footprint compact for space-constrained controller boards. Robust implementation still requires careful grounding, surge protection at exposed connectors, and configurable termination so unused network sections do not load the bus.
Recommandé
Remote I/O Module
The ISL8487IB-T suits a remote input/output module that communicates with a central controller over a multidrop RS-485 bus. The low-power 5 V transceiver helps maintain system efficiency, and one-quarter unit loading improves compatibility with networks containing multiple remote modules. Its half-duplex mode allows the module to send updated sensor states while receiving configuration commands over the same pair of conductors. The circuit should include a low-impedance ground connection between the bus and transceiver, and production testing should cover idle bias, driver enable transitions, and receiver operation across the intended temperature range.
Recommandé
Test and Measurement Instrument
The ISL8487IB-T can provide the physical interface for a test and measurement instrument that communicates with a host computer or laboratory controller using RS-485 or RS-422. The compact SOIC package supports dense instrument electronics, and the one-quarter unit-load rating can accommodate multiple instruments without unnecessarily loading the bus. Low-power characteristics also help control self-heating in precision equipment. For laboratory environments with long cables, check grounding, isolate ground-potential differences, and use the balanced interface in accordance with the ISL8487 family application guidance.
Recommandé
Embedded Serial Controller
The ISL8487IB-T is a practical choice for an embedded controller that must add an isolated or protected-by-layout RS-485/RS-422 port alongside its digital processor. The 5 V interface and low-power operation align with common embedded power rails, while the half-duplex transceiver minimizes external circuitry compared with a full-duplex implementation. The controller must manage TX/RX direction logic and provide a defined state during receive operation. During PCB layout, keep the bus-side traces short and away from switching nodes, and verify the transceiver's logic-level compatibility with the processor.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ISL8487IB-T — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ISL8488 | ISL8489E | ISL8489EIB | ISL8489IB | MAX483ECSA+T |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Analog Devices |
| Package | 8-SOIC, 0.154 in (3.90 mm) Width | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supported Standards | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-485 and RS-422 |
| Power Class | Low Power | Low Power | Low Power | Low Power | Low Power | Low Power |
Principaux différenciateurs
- Lower bus loading supports greater network flexibility (vs ISL8489IB)
- Compact single-transceiver implementation (vs MAX483ECSA+T)
- Low-power operation for compact serial interfaces (vs ISL8488)
Notes de conception
Place the ISL8487IB-T close to the RS-485 or RS-422 connector and route the differential bus pair as a closely coupled pair. Provide a continuous ground-reference path between the transceiver and connector, while keeping switching-regulator and high-current return paths away from the receiver input. This arrangement reduces susceptibility to common-mode noise and improves the margin between the transmitter and receiver thresholds.
Do not assume that matching the 8-pin SOIC footprint guarantees drop-in compatibility. Verify driver input polarity, receiver enable behavior, supply range, receiver thresholds, unit load, maximum data rate, and ESD rating for every proposed substitute. The bus also requires an intentional termination and biasing strategy; do not populate fixed termination at every node because excessive termination can reduce driver voltage and impair communication.
Validate the completed network with the intended cable, node spacing, termination, and data rate. A one-quarter unit-load transceiver can support more nodes than a one-unit-load device, but capacitive loading and reflections still depend on topology. Use controlled-direction firmware to avoid bus contention, allow the receiver to recover before returning to transmit, and test the system across voltage, temperature, and power-up conditions.
Informations de conformité
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current Renesas product documentation or declaration of compliance. AEC-Q100 is not applicable to this general-purpose interface transceiver unless the manufacturer identifies a specific automotive-qualified ordering variant.