ISL8487IB-T - Low-Power RS-485/422 Transceiver | Renesas
MPN: ISL8487IB-T ✓ 啟用中ISL8487IB-T 概覽
An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level transmit and receive signals into differential bus signals and converts incoming differential signals into CMOS-compatible logic. The RS-485 standard supports balanced, multipoint communication over relatively long cables, while RS-422 is commonly used for point-to-point links. Within the interface hierarchy, the ISL8487IB-T belongs to the RS-485/RS-422 transceiver class of communication interface ICs.
The device is identified as a one-transceiver, half-duplex component with one-quarter unit-load drive capability. Its 5 V operation and low-power design make it appropriate for embedded systems in which every milliampere affects system thermal performance or battery life. The 8-pin SOIC package also supports compact, surface-mount PCB construction while providing enough pins for separate driver input, receiver output, enable control, supply, and ground connections.
The one-quarter unit-load rating enables the device to present only one quarter of a standard unit load to the bus. This loading capability allows more nodes to share a multidrop network than a one-unit-load transceiver while preserving signal integrity. Its half-duplex architecture supports shared transmit and receive circuitry, reducing board area and simplifying bus direction control in designs that do not require simultaneous full-duplex operation.
Typical uses include industrial sensor gateways, programmable logic controller communication, building automation, remote I/O modules, instrumentation, and embedded serial controllers. The part is particularly appropriate when the bus cable length, node count, ground-reference conditions, and data rate remain compatible with the limits of the Renesas ISL8487 family. A network should still be checked for termination, biasing, and transient protection requirements.
PCB implementation should keep the transceiver close to the bus connector and provide a continuous ground reference between the transceiver and connector. Place network termination and any failsafe biasing components where they can be selectively configured, and confirm that the logic interface voltage of the connected controller is compatible with the transceiver. The SOIC footprint simplifies assembly, although exposed bus and logic pins still require careful handling during soldering.
This product page combines package and interface details, commercially focused sourcing guidance, pin-compatible candidate evaluation, and application-specific design guidance. It is intended to help engineers verify the electrical trade-offs and board-level requirements before integrating the ISL8487IB-T into an RS-485 or RS-422 system.
直接替換替代品,適用於 ISL8487IB-T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ISL8487IB-T (相同外形與佔位) — 差異在於 Package, Slew Rate, Mounting Type, Product Type, Supported Standards.
ISL8488IP
✅ 直接替換聯絡詢價
查看資料表 →ISL8489E
✅ 直接替換📋 參考替代品(不在目錄中)
ISL8489EIB
✅ 直接替換聯絡詢價
查看資料表 →ISL8489IB
✅ 直接替換聯絡詢價
查看資料表 →MAX483ECSA+T
✅ 直接替換📋 參考替代品(不在目錄中)
ISL8487IB-T 規格
| Transceiver Configuration | 1/1 Transceiver Half |
| Supported Standards | RS-422 and RS-485 |
| 供應電壓 | 5 V |
| Bus Unit Load | 1/4 Unit Load |
| Communication Mode | Half Duplex |
| ESD Protection | ESD Protected |
| Power Class | Low Power |
| Slew Rate | High Speed or Slew Rate Limited |
| 封裝 | 8-SOIC, 0.154 in (3.90 mm) Width |
| 安裝類型 | Surface Mount |
| 腳位數 | 8 Pins |
| Manufacturer | Renesas Electronics Corporation |
ISL8487IB-T 8-soic, 0.154 in (3.90 mm) width 腳位配置指南
ISL8487IB-T(8-soic, 0.154 in (3.90 mm) width 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ISL8487IB-T.
請參閱 資料表 以查看完整腳位配置。
典型應用
ISL8487IB-T 適用於 6 應用s: Industrial Sensor Gateway, PLC Communication Module, Building Automation Controller, Remote I/O Module, Test and Measurement Instrument, Embedded Serial Controller.
Industrial Sensor Gateway
The ISL8487IB-T fits an industrial sensor gateway that must connect several remote sensor nodes to a controller over an RS-485 bus. Its one-quarter unit-load capability allows a higher node count than a one-unit-load transceiver, while the low-power 5 V operation reduces supply demand in distributed equipment. The half-duplex arrangement uses one physical bus for command transmission and sensor responses. Designers should place the transceiver near the bus connector, provide a continuous ground path, and verify termination and failsafe biasing for the actual cable length and topology.
推薦
PLC Communication Module
The ISL8487IB-T is appropriate for a programmable logic controller communication module that exchanges commands and process data with remote equipment over a balanced bus. Its 5 V operation supports compact controller boards, and the one-quarter unit-load rating helps preserve bus loading margin when several modules are connected. Half-duplex operation simplifies the physical interface, but firmware must control direction switching and account for turnaround time. Validate receive thresholds and bus timing against the network's data rate and termination arrangement before releasing the circuit.
推薦
Building Automation Controller
A building automation controller can use the ISL8487IB-T to connect thermostats, access panels, lighting controllers, and environmental sensors through an RS-485 network. Low power is useful in remotely powered or thermally constrained control cabinets, while the one-quarter unit-load interface supports a larger collection of bus nodes. The 8-pin SOIC keeps the footprint compact for space-constrained controller boards. Robust implementation still requires careful grounding, surge protection at exposed connectors, and configurable termination so unused network sections do not load the bus.
推薦
Remote I/O Module
The ISL8487IB-T suits a remote input/output module that communicates with a central controller over a multidrop RS-485 bus. The low-power 5 V transceiver helps maintain system efficiency, and one-quarter unit loading improves compatibility with networks containing multiple remote modules. Its half-duplex mode allows the module to send updated sensor states while receiving configuration commands over the same pair of conductors. The circuit should include a low-impedance ground connection between the bus and transceiver, and production testing should cover idle bias, driver enable transitions, and receiver operation across the intended temperature range.
推薦
Test and Measurement Instrument
The ISL8487IB-T can provide the physical interface for a test and measurement instrument that communicates with a host computer or laboratory controller using RS-485 or RS-422. The compact SOIC package supports dense instrument electronics, and the one-quarter unit-load rating can accommodate multiple instruments without unnecessarily loading the bus. Low-power characteristics also help control self-heating in precision equipment. For laboratory environments with long cables, check grounding, isolate ground-potential differences, and use the balanced interface in accordance with the ISL8487 family application guidance.
推薦
Embedded Serial Controller
The ISL8487IB-T is a practical choice for an embedded controller that must add an isolated or protected-by-layout RS-485/RS-422 port alongside its digital processor. The 5 V interface and low-power operation align with common embedded power rails, while the half-duplex transceiver minimizes external circuitry compared with a full-duplex implementation. The controller must manage TX/RX direction logic and provide a defined state during receive operation. During PCB layout, keep the bus-side traces short and away from switching nodes, and verify the transceiver's logic-level compatibility with the processor.
推薦
推薦產品摘要
工程參考資料,適用於 ISL8487IB-T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ISL8488 | ISL8489E | ISL8489EIB | ISL8489IB | MAX483ECSA+T |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Analog Devices |
| Package | 8-SOIC, 0.154 in (3.90 mm) Width | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supported Standards | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-485 and RS-422 |
| Power Class | Low Power | Low Power | Low Power | Low Power | Low Power | Low Power |
主要差異化特點
- Lower bus loading supports greater network flexibility (對比ISL8489IB)
- Compact single-transceiver implementation (對比MAX483ECSA+T)
- Low-power operation for compact serial interfaces (對比ISL8488)
設計說明
Place the ISL8487IB-T close to the RS-485 or RS-422 connector and route the differential bus pair as a closely coupled pair. Provide a continuous ground-reference path between the transceiver and connector, while keeping switching-regulator and high-current return paths away from the receiver input. This arrangement reduces susceptibility to common-mode noise and improves the margin between the transmitter and receiver thresholds.
Do not assume that matching the 8-pin SOIC footprint guarantees drop-in compatibility. Verify driver input polarity, receiver enable behavior, supply range, receiver thresholds, unit load, maximum data rate, and ESD rating for every proposed substitute. The bus also requires an intentional termination and biasing strategy; do not populate fixed termination at every node because excessive termination can reduce driver voltage and impair communication.
Validate the completed network with the intended cable, node spacing, termination, and data rate. A one-quarter unit-load transceiver can support more nodes than a one-unit-load device, but capacitive loading and reflections still depend on topology. Use controlled-direction firmware to avoid bus contention, allow the receiver to recover before returning to transmit, and test the system across voltage, temperature, and power-up conditions.
合規資訊
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current Renesas product documentation or declaration of compliance. AEC-Q100 is not applicable to this general-purpose interface transceiver unless the manufacturer identifies a specific automotive-qualified ordering variant.