ISL8487IB-T - Low-Power RS-485/422 Transceiver | Renesas
MPN: ISL8487IB-T ✓ Hoạt độngISL8487IB-T Tóm tắt
An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level transmit and receive signals into differential bus signals and converts incoming differential signals into CMOS-compatible logic. The RS-485 standard supports balanced, multipoint communication over relatively long cables, while RS-422 is commonly used for point-to-point links. Within the interface hierarchy, the ISL8487IB-T belongs to the RS-485/RS-422 transceiver class of communication interface ICs.
The device is identified as a one-transceiver, half-duplex component with one-quarter unit-load drive capability. Its 5 V operation and low-power design make it appropriate for embedded systems in which every milliampere affects system thermal performance or battery life. The 8-pin SOIC package also supports compact, surface-mount PCB construction while providing enough pins for separate driver input, receiver output, enable control, supply, and ground connections.
The one-quarter unit-load rating enables the device to present only one quarter of a standard unit load to the bus. This loading capability allows more nodes to share a multidrop network than a one-unit-load transceiver while preserving signal integrity. Its half-duplex architecture supports shared transmit and receive circuitry, reducing board area and simplifying bus direction control in designs that do not require simultaneous full-duplex operation.
Typical uses include industrial sensor gateways, programmable logic controller communication, building automation, remote I/O modules, instrumentation, and embedded serial controllers. The part is particularly appropriate when the bus cable length, node count, ground-reference conditions, and data rate remain compatible with the limits of the Renesas ISL8487 family. A network should still be checked for termination, biasing, and transient protection requirements.
PCB implementation should keep the transceiver close to the bus connector and provide a continuous ground reference between the transceiver and connector. Place network termination and any failsafe biasing components where they can be selectively configured, and confirm that the logic interface voltage of the connected controller is compatible with the transceiver. The SOIC footprint simplifies assembly, although exposed bus and logic pins still require careful handling during soldering.
This product page combines package and interface details, commercially focused sourcing guidance, pin-compatible candidate evaluation, and application-specific design guidance. It is intended to help engineers verify the electrical trade-offs and board-level requirements before integrating the ISL8487IB-T into an RS-485 or RS-422 system.
Bộ thay thế dễ dàng lắp đặt cho ISL8487IB-T — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ISL8487IB-T (cùng hình factor và footprint) — khác nhau ở Package, Slew Rate, Mounting Type, Product Type, Supported Standards.
ISL8488IP
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ISL8489E
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ISL8489EIB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ISL8489IB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX483ECSA+T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ISL8487IB-T Thông số kỹ thuật
| Transceiver Configuration | 1/1 Transceiver Half |
| Supported Standards | RS-422 and RS-485 |
| Điện áp cung cấp | 5 V |
| Bus Unit Load | 1/4 Unit Load |
| Communication Mode | Half Duplex |
| ESD Protection | ESD Protected |
| Power Class | Low Power |
| Slew Rate | High Speed or Slew Rate Limited |
| Hộp | 8-SOIC, 0.154 in (3.90 mm) Width |
| Kiểu lắp đặt | Surface Mount |
| Số lượng chân | 8 Pins |
| Manufacturer | Renesas Electronics Corporation |
Hướng dẫn cấu hình chân ISL8487IB-T 8-soic, 0.154 in (3.90 mm) width
Cấu hình chân cho ISL8487IB-T (8-soic, 0.154 in (3.90 mm) width gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ISL8487IB-T.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ISL8487IB-T phù hợp cho 6 Áp dụngs: Industrial Sensor Gateway, PLC Communication Module, Building Automation Controller, Remote I/O Module, Test and Measurement Instrument, Embedded Serial Controller.
Industrial Sensor Gateway
The ISL8487IB-T fits an industrial sensor gateway that must connect several remote sensor nodes to a controller over an RS-485 bus. Its one-quarter unit-load capability allows a higher node count than a one-unit-load transceiver, while the low-power 5 V operation reduces supply demand in distributed equipment. The half-duplex arrangement uses one physical bus for command transmission and sensor responses. Designers should place the transceiver near the bus connector, provide a continuous ground path, and verify termination and failsafe biasing for the actual cable length and topology.
Được đề xuất
PLC Communication Module
The ISL8487IB-T is appropriate for a programmable logic controller communication module that exchanges commands and process data with remote equipment over a balanced bus. Its 5 V operation supports compact controller boards, and the one-quarter unit-load rating helps preserve bus loading margin when several modules are connected. Half-duplex operation simplifies the physical interface, but firmware must control direction switching and account for turnaround time. Validate receive thresholds and bus timing against the network's data rate and termination arrangement before releasing the circuit.
Được đề xuất
Building Automation Controller
A building automation controller can use the ISL8487IB-T to connect thermostats, access panels, lighting controllers, and environmental sensors through an RS-485 network. Low power is useful in remotely powered or thermally constrained control cabinets, while the one-quarter unit-load interface supports a larger collection of bus nodes. The 8-pin SOIC keeps the footprint compact for space-constrained controller boards. Robust implementation still requires careful grounding, surge protection at exposed connectors, and configurable termination so unused network sections do not load the bus.
Được đề xuất
Remote I/O Module
The ISL8487IB-T suits a remote input/output module that communicates with a central controller over a multidrop RS-485 bus. The low-power 5 V transceiver helps maintain system efficiency, and one-quarter unit loading improves compatibility with networks containing multiple remote modules. Its half-duplex mode allows the module to send updated sensor states while receiving configuration commands over the same pair of conductors. The circuit should include a low-impedance ground connection between the bus and transceiver, and production testing should cover idle bias, driver enable transitions, and receiver operation across the intended temperature range.
Được đề xuất
Test and Measurement Instrument
The ISL8487IB-T can provide the physical interface for a test and measurement instrument that communicates with a host computer or laboratory controller using RS-485 or RS-422. The compact SOIC package supports dense instrument electronics, and the one-quarter unit-load rating can accommodate multiple instruments without unnecessarily loading the bus. Low-power characteristics also help control self-heating in precision equipment. For laboratory environments with long cables, check grounding, isolate ground-potential differences, and use the balanced interface in accordance with the ISL8487 family application guidance.
Được đề xuất
Embedded Serial Controller
The ISL8487IB-T is a practical choice for an embedded controller that must add an isolated or protected-by-layout RS-485/RS-422 port alongside its digital processor. The 5 V interface and low-power operation align with common embedded power rails, while the half-duplex transceiver minimizes external circuitry compared with a full-duplex implementation. The controller must manage TX/RX direction logic and provide a defined state during receive operation. During PCB layout, keep the bus-side traces short and away from switching nodes, and verify the transceiver's logic-level compatibility with the processor.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ISL8487IB-T — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ISL8488 | ISL8489E | ISL8489EIB | ISL8489IB | MAX483ECSA+T |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Analog Devices |
| Package | 8-SOIC, 0.154 in (3.90 mm) Width | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supported Standards | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-485 and RS-422 |
| Power Class | Low Power | Low Power | Low Power | Low Power | Low Power | Low Power |
Bảo phân biệt quan trọng
- Lower bus loading supports greater network flexibility (vsISL8489IB)
- Compact single-transceiver implementation (vsMAX483ECSA+T)
- Low-power operation for compact serial interfaces (vsISL8488)
Ghi chú thiết kế
Place the ISL8487IB-T close to the RS-485 or RS-422 connector and route the differential bus pair as a closely coupled pair. Provide a continuous ground-reference path between the transceiver and connector, while keeping switching-regulator and high-current return paths away from the receiver input. This arrangement reduces susceptibility to common-mode noise and improves the margin between the transmitter and receiver thresholds.
Do not assume that matching the 8-pin SOIC footprint guarantees drop-in compatibility. Verify driver input polarity, receiver enable behavior, supply range, receiver thresholds, unit load, maximum data rate, and ESD rating for every proposed substitute. The bus also requires an intentional termination and biasing strategy; do not populate fixed termination at every node because excessive termination can reduce driver voltage and impair communication.
Validate the completed network with the intended cable, node spacing, termination, and data rate. A one-quarter unit-load transceiver can support more nodes than a one-unit-load device, but capacitive loading and reflections still depend on topology. Use controlled-direction firmware to avoid bus contention, allow the receiver to recover before returning to transmit, and test the system across voltage, temperature, and power-up conditions.
Thông tin tuân thủ
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current Renesas product documentation or declaration of compliance. AEC-Q100 is not applicable to this general-purpose interface transceiver unless the manufacturer identifies a specific automotive-qualified ordering variant.