ISL8487IB-T - Low-Power RS-485/422 Transceiver | Renesas
料号: ISL8487IB-T ✓ 量产中ISL8487IB-T 概述
An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level transmit and receive signals into differential bus signals and converts incoming differential signals into CMOS-compatible logic. The RS-485 standard supports balanced, multipoint communication over relatively long cables, while RS-422 is commonly used for point-to-point links. Within the interface hierarchy, the ISL8487IB-T belongs to the RS-485/RS-422 transceiver class of communication interface ICs.
The device is identified as a one-transceiver, half-duplex component with one-quarter unit-load drive capability. Its 5 V operation and low-power design make it appropriate for embedded systems in which every milliampere affects system thermal performance or battery life. The 8-pin SOIC package also supports compact, surface-mount PCB construction while providing enough pins for separate driver input, receiver output, enable control, supply, and ground connections.
The one-quarter unit-load rating enables the device to present only one quarter of a standard unit load to the bus. This loading capability allows more nodes to share a multidrop network than a one-unit-load transceiver while preserving signal integrity. Its half-duplex architecture supports shared transmit and receive circuitry, reducing board area and simplifying bus direction control in designs that do not require simultaneous full-duplex operation.
Typical uses include industrial sensor gateways, programmable logic controller communication, building automation, remote I/O modules, instrumentation, and embedded serial controllers. The part is particularly appropriate when the bus cable length, node count, ground-reference conditions, and data rate remain compatible with the limits of the Renesas ISL8487 family. A network should still be checked for termination, biasing, and transient protection requirements.
PCB implementation should keep the transceiver close to the bus connector and provide a continuous ground reference between the transceiver and connector. Place network termination and any failsafe biasing components where they can be selectively configured, and confirm that the logic interface voltage of the connected controller is compatible with the transceiver. The SOIC footprint simplifies assembly, although exposed bus and logic pins still require careful handling during soldering.
This product page combines package and interface details, commercially focused sourcing guidance, pin-compatible candidate evaluation, and application-specific design guidance. It is intended to help engineers verify the electrical trade-offs and board-level requirements before integrating the ISL8487IB-T into an RS-485 or RS-422 system.
直接替换替代料: ISL8487IB-T ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ISL8487IB-T (相同外形与封装尺寸) ——差异在于 Package, Slew Rate, Mounting Type, Product Type, Supported Standards.
ISL8488IP
✅ 直接替换联系询价
查看数据手册 →ISL8489E
✅ 直接替换📋 参考替代料(不在目录中)
ISL8489EIB
✅ 直接替换联系询价
查看数据手册 →ISL8489IB
✅ 直接替换联系询价
查看数据手册 →MAX483ECSA+T
✅ 直接替换📋 参考替代料(不在目录中)
ISL8487IB-T 规格参数
| Transceiver Configuration | 1/1 Transceiver Half |
| Supported Standards | RS-422 and RS-485 |
| 电源电压 | 5 V |
| Bus Unit Load | 1/4 Unit Load |
| Communication Mode | Half Duplex |
| ESD Protection | ESD Protected |
| Power Class | Low Power |
| Slew Rate | High Speed or Slew Rate Limited |
| 封装 | 8-SOIC, 0.154 in (3.90 mm) Width |
| 安装类型 | Surface Mount |
| 引脚数 | 8 Pins |
| Manufacturer | Renesas Electronics Corporation |
ISL8487IB-T 8-soic, 0.154 in (3.90 mm) width 引脚配置指南
ISL8487IB-T(8-soic, 0.154 in (3.90 mm) width 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ISL8487IB-T.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ISL8487IB-T 适用于 6 应用s: Industrial Sensor Gateway, PLC Communication Module, Building Automation Controller, Remote I/O Module, Test and Measurement Instrument, Embedded Serial Controller.
Industrial Sensor Gateway
The ISL8487IB-T fits an industrial sensor gateway that must connect several remote sensor nodes to a controller over an RS-485 bus. Its one-quarter unit-load capability allows a higher node count than a one-unit-load transceiver, while the low-power 5 V operation reduces supply demand in distributed equipment. The half-duplex arrangement uses one physical bus for command transmission and sensor responses. Designers should place the transceiver near the bus connector, provide a continuous ground path, and verify termination and failsafe biasing for the actual cable length and topology.
推荐
PLC Communication Module
The ISL8487IB-T is appropriate for a programmable logic controller communication module that exchanges commands and process data with remote equipment over a balanced bus. Its 5 V operation supports compact controller boards, and the one-quarter unit-load rating helps preserve bus loading margin when several modules are connected. Half-duplex operation simplifies the physical interface, but firmware must control direction switching and account for turnaround time. Validate receive thresholds and bus timing against the network's data rate and termination arrangement before releasing the circuit.
推荐
Building Automation Controller
A building automation controller can use the ISL8487IB-T to connect thermostats, access panels, lighting controllers, and environmental sensors through an RS-485 network. Low power is useful in remotely powered or thermally constrained control cabinets, while the one-quarter unit-load interface supports a larger collection of bus nodes. The 8-pin SOIC keeps the footprint compact for space-constrained controller boards. Robust implementation still requires careful grounding, surge protection at exposed connectors, and configurable termination so unused network sections do not load the bus.
推荐
Remote I/O Module
The ISL8487IB-T suits a remote input/output module that communicates with a central controller over a multidrop RS-485 bus. The low-power 5 V transceiver helps maintain system efficiency, and one-quarter unit loading improves compatibility with networks containing multiple remote modules. Its half-duplex mode allows the module to send updated sensor states while receiving configuration commands over the same pair of conductors. The circuit should include a low-impedance ground connection between the bus and transceiver, and production testing should cover idle bias, driver enable transitions, and receiver operation across the intended temperature range.
推荐
Test and Measurement Instrument
The ISL8487IB-T can provide the physical interface for a test and measurement instrument that communicates with a host computer or laboratory controller using RS-485 or RS-422. The compact SOIC package supports dense instrument electronics, and the one-quarter unit-load rating can accommodate multiple instruments without unnecessarily loading the bus. Low-power characteristics also help control self-heating in precision equipment. For laboratory environments with long cables, check grounding, isolate ground-potential differences, and use the balanced interface in accordance with the ISL8487 family application guidance.
推荐
Embedded Serial Controller
The ISL8487IB-T is a practical choice for an embedded controller that must add an isolated or protected-by-layout RS-485/RS-422 port alongside its digital processor. The 5 V interface and low-power operation align with common embedded power rails, while the half-duplex transceiver minimizes external circuitry compared with a full-duplex implementation. The controller must manage TX/RX direction logic and provide a defined state during receive operation. During PCB layout, keep the bus-side traces short and away from switching nodes, and verify the transceiver's logic-level compatibility with the processor.
推荐
推荐产品汇总
工程参考数据: ISL8487IB-T ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ISL8488 | ISL8489E | ISL8489EIB | ISL8489IB | MAX483ECSA+T |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Analog Devices |
| Package | 8-SOIC, 0.154 in (3.90 mm) Width | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supported Standards | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-485 and RS-422 |
| Power Class | Low Power | Low Power | Low Power | Low Power | Low Power | Low Power |
关键差异点
- Lower bus loading supports greater network flexibility (对比 ISL8489IB)
- Compact single-transceiver implementation (对比 MAX483ECSA+T)
- Low-power operation for compact serial interfaces (对比 ISL8488)
设计说明
Place the ISL8487IB-T close to the RS-485 or RS-422 connector and route the differential bus pair as a closely coupled pair. Provide a continuous ground-reference path between the transceiver and connector, while keeping switching-regulator and high-current return paths away from the receiver input. This arrangement reduces susceptibility to common-mode noise and improves the margin between the transmitter and receiver thresholds.
Do not assume that matching the 8-pin SOIC footprint guarantees drop-in compatibility. Verify driver input polarity, receiver enable behavior, supply range, receiver thresholds, unit load, maximum data rate, and ESD rating for every proposed substitute. The bus also requires an intentional termination and biasing strategy; do not populate fixed termination at every node because excessive termination can reduce driver voltage and impair communication.
Validate the completed network with the intended cable, node spacing, termination, and data rate. A one-quarter unit-load transceiver can support more nodes than a one-unit-load device, but capacitive loading and reflections still depend on topology. Use controlled-direction firmware to avoid bus contention, allow the receiver to recover before returning to transmit, and test the system across voltage, temperature, and power-up conditions.
合规信息
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current Renesas product documentation or declaration of compliance. AEC-Q100 is not applicable to this general-purpose interface transceiver unless the manufacturer identifies a specific automotive-qualified ordering variant.