LM5164DDAR - 100V 1A Sync Buck Converter | Texas Instruments
Référence : LM5164DDAR ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $2.45 | $2,45 |
| 10 | $2.2 | $22,00 |
| 100 | $1.85 | $185,00 |
| 500 | $1.65 | $825,00 |
| 1 000 | $1.47 | $1 470,00 |
LM5164DDAR Présentation
A synchronous buck converter is a type of DC-DC step-down regulator in the power management IC hierarchy that uses two active switches instead of a diode to achieve higher efficiency, especially at low output voltages. The LM5164 integrates both high-side and low-side MOSFETs, simplifying design and reducing external component count.
Key features include an ultra-low quiescent current that extends battery life in always-on systems, and a wide input range that eliminates external surge suppression components. An open-drain PGOOD indicator supports power sequencing, fault reporting, and output voltage monitoring. The 1 MHz switching frequency allows small external inductors and capacitors, and the device supports 100% duty cycle for low dropout operation.
The LM5164 uses peak current-mode control with internal compensation, providing fast transient response and stable operation over a wide range of output capacitors. Integrated low-RDS(on) MOSFETs minimize conduction losses. Cycle-by-cycle current limiting, thermal shutdown, and hiccup-mode short-circuit protection ensure robust operation in harsh environments.
Typical applications include industrial 24-V and 48-V bus power supplies, 12-V automotive body electronics, motor drives, battery management systems, and always-on telematics. The ultra-low IQ makes it ideal for remote monitoring systems that spend most of their life in standby.
Design tip: provide a solid ground plane and adequate copper area under the PowerPAD for thermal dissipation, and maintain sufficient creepage distance between high-voltage and low-voltage traces given the 1.27-mm pin pitch.
Alternatives de remplacement direct pour LM5164DDAR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM5164DDAR (même facteur de forme et même empreinte) — différant par Package, Pin Pitch, Topology, Automotive Qualification, Output Voltage Range.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
LM5164QDDARQ1
✅ Remplacement direct✓ En stock
$1.95 / unité
Voir la fiche technique →LM5163DDAR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LM5165DDAR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPS54360QDDARQ1
⚡ Même boîtier ⚠️ Spécifications non vérifiées✓ En stock
$2.45 / unité
Voir la fiche technique →LM2596SX-ADJ/NOPB-Q1
⚡ Même boîtier ⚠️ Spécifications non vérifiées✓ En stock
$1.02 / unité
Voir la fiche technique →LM5164DDAR Valeurs maximales et caractéristiques électriques
| Topologie | Synchronous Buck (step-down) |
| Plage de tension d'entrée | 6 V to 100 V |
| Courant de sortie maximal | 1 A |
| Plage de tension de sortie | Adjustable, down to 1.2 V |
| Nombre de sorties | 1 |
| Fréquence de commutation | 1 MHz |
| Control Architecture | Peak current-mode, internal compensation |
| Duty Cycle | 100% (low dropout operation) |
| PGOOD Indicator | Open-drain PGOOD |
| Protection Features | Cycle-by-cycle current limit, thermal shutdown, hiccup mode |
| Température de fonctionnement | -40C to +150C (TJ) |
| Boîtier | 8-PowerSOIC (HSOIC-8, DDAR), 0.154 in / 3.90 mm width |
| Pin Pitch | 1.27 mm (high-voltage spacing) |
| Type de montage | Surface Mount |
Configuration des broches de LM5164DDAR
| Broche 1 | VIN — Input supply voltage, 6 V to 100 V |
| Broche 2 | EN — Enable input with internal regulation |
| Broche 3 | AGRT / AGND — Analog ground reference |
| Broche 4 | FB — Feedback input for output voltage adjustment |
| Broche 5 | PGOOD — Open-drain power good indicator |
| Broche 6 | BOOT — Bootstrap capacitor for high-side driver |
| Broche 7 | SW — Switching node (connected to inductor) |
| Broche 8 | PGND — Power ground |
| Broche 9 | PowerPAD — Thermal pad - solder to ground plane for heat dissipation |
Applications typiques
LM5164DDAR convient pour 6 applications: 48-V Industrial Bus Power Supply, Automotive 12-V Body Electronics, Battery Management Systems, Motor Drives and Actuators, Telematics and Remote Monitoring, Test and Measurement Instrumentation.
48-V Industrial Bus Power Supply
The LM5164DDAR's 6-V to 100-V input range directly covers 48-V industrial buses with wide transient headroom, eliminating external TVS or pre-regulation stages. As a synchronous buck with integrated MOSFETs, it converts 48 V down to 5 V or 3.3 V logic rails at up to 1 A with 1 MHz switching, keeping the inductor small. The ultra-low IQ benefits always-on factory monitoring nodes that idle most of the time.
Recommandé
Automotive 12-V Body Electronics
In automotive body ECUs (lighting, door modules, telematics), the LM5164 handles 12-V rail load-dump and cold-crank transients via its 100-V input rating and 100% duty cycle support. The open-drain PGOOD output enables fault reporting to the MCU, and hiccup-mode protection survives persistent shorts. The AEC-Q100 qualified LM5164QDDARQ1 covers designs requiring automotive qualification.
Recommandé
Battery Management Systems
The LM5164 provides a regulated low-voltage bias rail from high-voltage battery stacks (24-V, 48-V packs) with ultra-low standby current that preserves pack state of charge. Its wide input range suits battery chemistries with large voltage swings, while cycle-by-cycle current limiting and thermal shutdown protect against fault conditions during charge and discharge events in BMS slave boards.
Recommandé
Motor Drives and Actuators
Motor drive controllers need a robust auxiliary supply derived from the high-voltage DC bus. The LM5164's rugged 100-V rating, hiccup-mode short-circuit protection, and -40C to +150C junction rating suit noisy motor drive environments. Its 1 MHz operation keeps the bias supply magnetics compact, and PGOOD sequencing ensures the gate-driver supply is valid before the MCU enables PWM outputs.
Recommandé
Telematics and Remote Monitoring
Always-on telematics and IoT gateways spend most of their life in sleep, making ultra-low quiescent current decisive for battery life. The LM5164DDAR's low IQ plus 100-V transient tolerance on vehicle or solar inputs keeps systems alive through surges while sipping microamps in standby. The PGOOD pin allows the host MCU to verify rail integrity before waking peripheral loads.
Recommandé
Test and Measurement Instrumentation
Bench and field instruments often have wide-range AC-adapter or battery inputs; the LM5164 generates clean intermediate rails from 6-V to 100-V sources with 1 MHz switching that is easy to filter. Internal compensation simplifies design across diverse output capacitor choices, and the adjustable output down to 1.2 V supports modern low-voltage analog and digital subsystems.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM5164DDAR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM5164QDDARQ1 | LM5163DDAR | LM5165DDAR |
|---|---|---|---|---|
| Package | HSOIC-8 (DDA) PowerPAD | HSOIC-8 PowerPAD - same | HSOIC-8 PowerPAD - same | HSOIC-8 PowerPAD - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Automotive Grade | No | Yes (AEC-Q100) | No | No (standard) |
Principaux différenciateurs
- 100-V input rating without external surge suppression (vs TPS54360QDDARQ1)
- Ultra-low quiescent current for always-on systems (vs LM2596SX-ADJ/NOPB-Q1)
- Pin-compatible 1.5 A upgrade path (vs LM5165DDAR)
Notes de conception
The LM5164DDAR uses a thermally enhanced 8-pin SO PowerPAD package. The PowerPAD must be soldered to a PCB ground pour with multiple thermal vias; an unsoldered pad significantly degrades thermal performance and may cause thermal shutdown at high VIN-VOUT differentials near the full 1 A load. Keep junction temperature below +150C per the TI datasheet.
Keep the loop from VIN capacitor, integrated MOSFETs, SW pin, and PGND as small as possible to minimize EMI. With a 1 MHz switching frequency, use short, wide traces for the SW node and place the bootstrap capacitor close to BOOT and SW pins. The 1.27-mm pin pitch aids high-voltage spacing, but still maintain creepage between 100-V and low-voltage traces.
Do not exceed the 100-V absolute maximum input, including transient spikes on inductive 48-V or automotive rails. Use the FB resistor divider with 1% tolerance resistors to set output accuracy, and reference the TI datasheet typical application section (lm5164.pdf) for recommended inductor and output capacitor ranges - internal compensation assumes output capacitance within the specified range.
Informations de conformité
RoHS compliance and lead-free status per standard TI production flow; the AEC-Q100 qualified variant is LM5164QDDARQ1. REACH/halogen status not stated in provided data.
