STM32L4R5ZIT6 - 32-bit ARM Cortex-M4 MCU 120MHz 2MB Flash LQFP-144 | STMicroelectronics
Référence : STM32L4R5ZIT6 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.4 | $164,00 |
| 100 | $14.2 | $1 420,00 |
| 500 | $12.85 | $6 425,00 |
| 1 000 | $11.4 | $11 400,00 |
STM32L4R5ZIT6 Présentation
An ARM Cortex-M4 microcontroller (MCU) is a 32-bit RISC processor core designed by Arm Holdings for embedded applications. It combines high computational performance with low power consumption, and the M4 variant adds a single-precision floating-point unit (FPU) plus DSP extensions. In the broader taxonomy, the STM32L4R5 belongs to the ultra-low-power microcontroller family (STM32L series), which sits below the mainstream STM32F series and above the ultra-low-power STM32L0 in ST's power-versus-performance spectrum. The "plus" designation (STM32L4+) indicates the higher-performance 120 MHz sub-family with Chrom-GRC graphics support.
Key features of the STM32L4R5ZIT6 include a FlexPowerControl architecture with multiple low-power modes (Shutdown at 33 nA, VBAT mode at 305 nA, Batch Acquisition Mode for partial wake-up), USB OTG with internal PHY, and a DFSDM (Digital Filter for Sigma-Delta Modulators) peripheral for sensor hub applications. It also features a Chrom-ART Accelerator for 2D graphics and an Octo-SPI interface for high-speed external Flash, along with cryptographic and AES-256 hardware accelerators for IoT security.
The device integrates the Cortex-M4 core with FPU and Memory Protection Unit, plus ST's ART Accelerator (Adaptive Real-Time memory accelerator) that allows 0-wait-state execution from Flash at the full 120 MHz clock speed. Up to 640 KB SRAM includes 32 KB of SRAM2 with parity check, retained in Standby mode and accessible via SRAM-based boot for secure firmware update. The LQFP-144 package exposes the full STM32L4R5 peripheral set: 3x 12-bit ADC (16-bit with oversampling), 2x DAC, 4x op-amps, 2x comparators, multiple timers, TFT controller, and MIPI-DSI support requires the larger BGA package.
Typical applications include wearable health monitors, smart sensors, IoT edge nodes, industrial HMI panels, low-power wireless modules (BLE/LoRa companion), battery-powered data loggers, and energy-harvesting systems. The 2 MB Flash supports over-the-air firmware updates and rich graphical user interfaces on small TFT displays without external memory.
When designing with the STM32L4R5ZIT6, use ST's STM32CubeMX and STM32CubeIDE toolchain for code generation, pin multiplexing, and power-consumption profiling. Source decoupling requires 100 nF X7R ceramic on every VDD/VDDA pair; the integrated SMPS step-down converter (when present on L4+ variants) should be configured with a 10 µH inductor per the application note AN4621. The LQFP-144 thermal performance typically permits 500 mA peak current draw at 120 MHz with a 2-layer FR4 board.
This page synthesizes distributor pricing tiers, drop-in compatible same-family STM32 alternatives, application-tailored companion MPNs, and practical low-power design guidance that complements the manufacturer datasheet.
Alternatives de remplacement direct pour STM32L4R5ZIT6 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec STM32L4R5ZIT6 (même facteur de forme et même empreinte) — différant par Package, ADC, Core, DAC, Graphics Accelerator.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
STM32L4R7ZIT6
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
STM32L4S5ZIT6
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
STM32L4R5ZIT6P
✅ Remplacement direct✓ En stock
$9.3 / unité
Voir la fiche technique →STM32L4R5ZGT6
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
STM32L4R9ZIT6
✅ Remplacement direct✓ En stock
$7.2 / unité
Voir la fiche technique →STM32L4R5ZIT6 Valeurs maximales et caractéristiques électriques
| Core | ARM Cortex-M4 with FPU |
| Fréquence d'horloge maximale | 120 MHz |
| Performance | 150 DMIPS / 273 CoreMark |
| Program Memory Size | 2 MB (2 M x 8) Flash |
| RAM Size | 640 KB |
| Supply Voltage Range | 1.71 V to 3.6 V |
| Plage de température de fonctionnement | -40 °C to +85 °C (grade 6), -40 °C to +125 °C (grade 7) |
| Boîtier | 144-LQFP (20 x 20 mm) |
| Nombre de broches | 144 |
| Type de montage | Surface Mount |
| ADC | 3 x 12-bit (up to 16-bit with hardware oversampling) |
| DAC | 2 x 12-bit |
| USB | USB OTG Full-Speed with internal PHY |
| Low-Power Modes | Shutdown 33 nA, VBAT mode 305 nA, Standby with RTC |
| External Memory Bus | Octo-SPI, FMC, SDMMC |
| Niveau MSL | 3 (168 hours) |
| Statut RoHS | Compliant |
Configuration des broches de STM32L4R5ZIT6
| Broche 1 | PE2 — GPIO PE2, TRACECLK |
| Broche 2 | PE3 — GPIO PE3, TRACED0 |
| Broche 3 | PE4 — GPIO PE4, TRACED1 |
| Broche 4 | PE5 — GPIO PE5, TRACED2 |
| Broche 5 | PE6 — GPIO PE6, TRACED3 |
| Broche 6 | VBAT — RTC backup power supply |
| Broche 7 | PC13 — GPIO PC13 (Tamper-RTC) |
| Broche 8 | PC14 — GPIO PC14 / OSC32_IN |
| Broche 9 | PC15 — GPIO PC15 / OSC32_OUT |
| Broche 10 | VSS — Ground |
| Broche 11 | VDD — Digital supply voltage |
| Broche 12 | PH0 — GPIO PH0 / OSC_IN |
| Broche 13 | PH1 — GPIO PH1 / OSC_OUT |
| Broche 14 | NRST — Reset input (active low) |
| Broche 15 | PC0 — GPIO PC0, ADC1_IN6 |
| Broche 16 | PC1 — GPIO PC1, ADC1_IN7 |
| Broche 17 | PC2 — GPIO PC2, ADC1_IN8 |
| Broche 18 | PC3 — GPIO PC3, ADC1_IN9 |
| Broche 19 | VSSA — Analog ground |
| Broche 20 | VDDA — Analog supply voltage |
| Broche 21 | PA0 — GPIO PA0, ADC1_IN5, UART4_TX |
| Broche 22 | PA1 — GPIO PA1, ADC1_IN6, UART4_RX |
| Broche 23 | PA2 — GPIO PA2, USART2_TX |
| Broche 24 | PA3 — GPIO PA3, USART2_RX |
| Broche 25 | VSS — Ground |
| Broche 26 | VDD — Digital supply voltage |
| Broche 27 | PA4 — GPIO PA4, SPI1_NSS, DAC_OUT1 |
| Broche 28 | PA5 — GPIO PA5, SPI1_SCK, DAC_OUT2 |
| Broche 29 | PA6 — GPIO PA6, SPI1_MISO, ADC1_IN11 |
| Broche 30 | PA7 — GPIO PA7, SPI1_MOSI, ADC1_IN12 |
| Broche 31 | PC4 — GPIO PC4, ADC1_IN13 |
| Broche 32 | PC5 — GPIO PC5, ADC1_IN14 |
| Broche 33 | PB0 — GPIO PB0, ADC1_IN15, TIM3_CH3 |
| Broche 34 | PB1 — GPIO PB1, ADC1_IN16, TIM3_CH4 |
| Broche 35 | PB2 — GPIO PB2, BOOT1 |
| Broche 36 | PE7 — GPIO PE7 |
| Broche 37 | PE8 — GPIO PE8 |
| Broche 38 | PE9 — GPIO PE9 |
| Broche 39 | PE10 — GPIO PE10 |
| Broche 40 | PE11 — GPIO PE11 |
| Broche 41 | PE12 — GPIO PE12 |
| Broche 42 | PE13 — GPIO PE13 |
| Broche 43 | PE14 — GPIO PE14 |
| Broche 44 | PE15 — GPIO PE15 |
| Broche 45 | PB10 — GPIO PB10, I2C2_SCL, USART3_TX |
| Broche 46 | PB11 — GPIO PB11, I2C2_SDA, USART3_RX |
| Broche 47 | VSS — Ground |
| Broche 48 | VDD — Digital supply voltage |
| Broche 49 | PB12 — GPIO PB12, SPI2_NSS, TIM1_BKIN |
| Broche 50 | PB13 — GPIO PB13, SPI2_SCK, USART3_CTS |
| Broche 51 | PB14 — GPIO PB14, SPI2_MISO, USART3_RTS |
| Broche 52 | PB15 — GPIO PB15, SPI2_MOSI, TIM1_CH3N |
| Broche 53 | PD8 — GPIO PD8 |
| Broche 54 | PD9 — GPIO PD9 |
| Broche 55 | PD10 — GPIO PD10 |
| Broche 56 | PD11 — GPIO PD11 |
| Broche 57 | PD12 — GPIO PD12 |
| Broche 58 | PD13 — GPIO PD13 |
| Broche 59 | PD14 — GPIO PD14 |
| Broche 60 | PD15 — GPIO PD15 |
| Broche 61 | PC6 — GPIO PC6, USART6_TX, TIM3_CH1 |
| Broche 62 | PC7 — GPIO PC7, USART6_RX, TIM3_CH2 |
| Broche 63 | PC8 — GPIO PC8, SDMMC_D0, TIM3_CH3 |
| Broche 64 | PC9 — GPIO PC9, SDMMC_D1, TIM3_CH4 |
| Broche 65 | PA8 — GPIO PA8, USART1_CK, TIM1_CH1, MCO |
| Broche 66 | PA9 — GPIO PA9, USART1_TX, TIM1_CH2 |
| Broche 67 | PA10 — GPIO PA10, USART1_RX, TIM1_CH3 |
| Broche 68 | PA11 — GPIO PA11, USB_OTG_FS_DM |
| Broche 69 | PA12 — GPIO PA12, USB_OTG_FS_DP |
| Broche 70 | PA13 — GPIO PA13, SWDIO |
| Broche 71 | PA14 — GPIO PA14, SWCLK |
| Broche 72 | PA15 — GPIO PA15, SPI1_NSS, TIM2_CH1 |
| Broche 73 | PC10 — GPIO PC10, USART3_TX, SDMMC_D2 |
| Broche 74 | PC11 — GPIO PC11, USART3_RX, SDMMC_D3 |
| Broche 75 | PC12 — GPIO PC12, USART3_CK, SDMMC_CK |
| Broche 76 | PD0 — GPIO PD0, CAN1_RX, FMC_D2 |
| Broche 77 | PD1 — GPIO PD1, CAN1_TX, FMC_D3 |
| Broche 78 | PD2 — GPIO PD2, SDMMC_CMD, TIM3_ETR |
| Broche 79 | PD3 — GPIO PD3, USART2_CTS, FMC_CLK |
| Broche 80 | PD4 — GPIO PD4, USART2_RTS, FMC_NOE |
| Broche 81 | PD5 — GPIO PD5, USART2_TX, FMC_NWE |
| Broche 82 | VSS — Ground |
| Broche 83 | VDD — Digital supply voltage |
| Broche 84 | PD6 — GPIO PD6, USART2_RX, FMC_NWAIT |
| Broche 85 | PD7 — GPIO PD7, USART2_CK, FMC_NE1 |
| Broche 86 | PB3 — GPIO PB3, SPI1_SCK, TIM2_CH2 |
| Broche 87 | PB4 — GPIO PB4, SPI1_MISO, TIM3_CH1 |
| Broche 88 | PB5 — GPIO PB5, SPI1_MOSI, I2C1_SMBA, TIM3_CH2 |
| Broche 89 | PB6 — GPIO PB6, I2C1_SCL, USART1_TX |
| Broche 90 | PB7 — GPIO PB7, I2C1_SDA, USART1_RX |
| Broche 91 | BOOT0 — Boot mode select |
| Broche 92 | PB8 — GPIO PB8, I2C1_SCL, TIM4_CH3 |
| Broche 93 | PB9 — GPIO PB9, I2C1_SDA, TIM4_CH4 |
| Broche 94 | PE0 — GPIO PE0, TIM4_ETR |
| Broche 95 | PE1 — GPIO PE1 |
| Broche 96 | VSS — Ground |
| Broche 97 | VDD — Digital supply voltage |
| Broche 98 | PF6 — GPIO PF6, TIM5_CH1, ADC3_IN4 |
| Broche 99 | PF7 — GPIO PF7, TIM5_CH2, ADC3_IN5 |
| Broche 100 | PF8 — GPIO PF8, TIM5_CH3, ADC3_IN6 |
| Broche 101 | PF9 — GPIO PF9, TIM5_CH4, ADC3_IN7 |
| Broche 102 | PF10 — GPIO PF10, ADC3_IN8 |
| Broche 103 | PF11 — GPIO PF11, ADC3_IN9 |
| Broche 104 | VSS — Ground |
| Broche 105 | VDD — Digital supply voltage |
| Broche 106 | PF12 — GPIO PF12, FSMC_A6 |
| Broche 107 | PF13 — GPIO PF13, FSMC_A7 |
| Broche 108 | PF14 — GPIO PF14, FSMC_A8 |
| Broche 109 | PF15 — GPIO PF15, FSMC_A9 |
| Broche 110 | PG0 — GPIO PG0, FSMC_A10 |
| Broche 111 | PG1 — GPIO PG1, FSMC_A11 |
| Broche 112 | PE2 — GPIO PE2, TRACECLK (alt) |
| Broche 113 | PE3 — GPIO PE3, TRACED0 (alt) |
| Broche 114 | PE4 — GPIO PE4, TRACED1 (alt) |
| Broche 115 | PE5 — GPIO PE5, TRACED2 (alt) |
| Broche 116 | PG2 — GPIO PG2, FSMC_A12 |
| Broche 117 | PG3 — GPIO PG3, FSMC_A13 |
| Broche 118 | PG4 — GPIO PG4, FSMC_A14 |
| Broche 119 | PG5 — GPIO PG5, FSMC_A15 |
| Broche 120 | PG6 — GPIO PG6 |
| Broche 121 | PG7 — GPIO PG7 |
| Broche 122 | PG8 — GPIO PG8 |
| Broche 123 | VSS — Ground |
| Broche 124 | VDD — Digital supply voltage |
| Broche 125 | PG9 — GPIO PG9, USART6_RX, FSMC_NE3 |
| Broche 126 | PG10 — GPIO PG10, FSMC_NE4 |
| Broche 127 | PG11 — GPIO PG11, FSMC_A24 |
| Broche 128 | PG12 — GPIO PG12, FSMC_NE1 |
| Broche 129 | PG13 — GPIO PG13, FSMC_A26 |
| Broche 130 | PG14 — GPIO PG14, FSMC_A27 |
| Broche 131 | VSS — Ground |
| Broche 132 | VDD — Digital supply voltage |
| Broche 133 | PG15 — GPIO PG15 |
| Broche 134 | PB3 — GPIO PB3, JTDO, SPI1_SCK |
| Broche 135 | PB4 — GPIO PB4, NJTRST, SPI1_MISO |
| Broche 136 | PB5 — GPIO PB5, SPI1_MOSI |
| Broche 137 | PB6 — GPIO PB6, USART1_TX |
| Broche 138 | PB7 — GPIO PB7, USART1_RX |
| Broche 139 | PB8 — GPIO PB8, I2C1_SCL |
| Broche 140 | PB9 — GPIO PB9, I2C1_SDA |
| Broche 141 | PE0 — GPIO PE0, TIM4_ETR |
| Broche 142 | PE1 — GPIO PE1 |
| Broche 143 | VSS — Ground |
| Broche 144 | VDD — Digital supply voltage |
Applications typiques
STM32L4R5ZIT6 convient pour 6 applications: Wearable Health Monitor, Industrial HMI Control Panel, Battery-Powered IoT Sensor Hub, Smart Energy Metering, Medical Infusion Pump Controller, Smart Sensor Hub for Predictive Maintenance.
Wearable Health Monitor
The STM32L4R5ZIT6 fits wearable health monitors due to its Cortex-M4F at 120 MHz capable of running heart-rate and motion-fusion DSP, plus 33 nA Shutdown current for multi-day battery life. Placed as the system MCU between a Li-Po cell and the analog front-end, it directly drives PPG/AFE signal chains via the four integrated op-amps and three 12-bit ADCs. Compared to Cortex-M0/M0+ alternatives it provides DSP and FPU on the same footprint, enabling step-count and ECG-R-peak detection without external DSP. The 2 MB Flash supports over-the-air firmware updates while the 640 KB SRAM buffers minutes of raw sensor data for later BLE upload.
Recommandé
Industrial HMI Control Panel
For industrial HMI panels, the STM32L4R5ZIT6 provides 120 MHz Cortex-M4 performance with Chrom-ART 2D acceleration to drive small TFT displays via SPI/8080 interfaces, plus FMC external bus for parallel memory expansion. Placed between the 24 V isolated supply and a 3.3 V LDO, it directly controls buttons, rotary encoders, and RS-485/Modbus via UART plus 50 MHz SPI. The 2 MB Flash hosts full graphics and a Chinese-English/Unicode character table. Compared to plain Cortex-M0 designs, the STM32L4R5ZIT6 renders multi-page interfaces without external SDRAM and supports Octo-SPI for faster TFT framebuffer access.
Recommandé
Battery-Powered IoT Sensor Hub
The STM32L4R5ZIT6 enables coin-cell / 2xAA battery sensor hubs, with 33 nA Shutdown and 1.1 µA Stop 2 with RTC allowing multi-year coin-cell runtime per AN4621. Placed as the central controller for MEMS microphones, environmental sensors, and BLE hand-off, it integrates the DFSDM digital filter for sigma-delta microphones without a dedicated audio DSP. The 2 MB Flash supports LoRaWAN/BLE stacks and OTA updates without external memory. Compared to discrete Cortex-M0+ designs the STM32L4R5ZIT6 adds Cortex-M4F DSP and is rated 1.71 V to 3.6 V, ideal for energy harvesting.
Recommandé
Smart Energy Metering
In smart energy meters, the STM32L4R5ZIT6 handles ADC sample aggregation, metrology DSP via Cortex-M4F MAC unit, and secure DLMS/COSEM firmware updates using its AES-256 hardware accelerator. Placed between the current-transformer / shunt front-end and the M-Bus / wireless PLC modem, it directly digitises up to three current channels with its 12-bit ADCs at oversampled 16-bit resolution. The 2 MB Flash holds protocol stacks for DLMS, M-Bus, and Wireless M-Bus plus regulatory firmware without external SPI flash. Compared to older Cortex-M3 designs, the STM32L4R5ZIT6 adds Standby 280 nA with RTC suitable for backup power modes.
Recommandé
Medical Infusion Pump Controller
The STM32L4R5ZIT6 powers infusion pump controllers, with its Cortex-M4F running PID motor control loops, the 2 MB Flash hosting IEC 62304/60335-compliant firmware, and USB OTG enabling host-side data export. Placed between a stepper driver and the keypad/display, it handles stepper commutation via its advanced timers while the integrated op-amps condition pressure and bubble-detection sensors. The 640 KB SRAM accommodates pressure waveform buffers, while AES-256 protects dosing calibration data. Compared to Cortex-M3 designs, the FPU ensures deterministic real-time control loop execution and the L4+ low-leakage features suit battery-backup mode.
Recommandé
Smart Sensor Hub for Predictive Maintenance
The STM32L4R5ZIT6 fits vibration and temperature sensor hubs in Industry 4.0, integrating the DFSDM digital filter for IEPE accelerometers and supporting FFT analysis via Cortex-M4F DSP with CMSIS-DSP library. Placed at industrial motor bearings, it runs self-powered from vibration energy harvesters thanks to 33 nA Shutdown and 1.71 V minimum supply. The 2 MB Flash hosts the wireless protocol stack (LoRa, BLE 5, or Wi-SUN) and predictive-maintenance ML models (TFLite-Micro). Compared to external-DSP designs, the single-chip integration reduces PCB area to under 20 mm square, which is decisive for retrofit-mount sensor units.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour STM32L4R5ZIT6 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | STM32L4R7ZIT6 | STM32L4S5ZIT6 | STM32L4R9ZIT6 |
|---|---|---|---|---|
| Package | 144-LQFP (20x20) | 144-LQFP (20x20) | 144-LQFP (20x20) | 144-LQFP (20x20) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Core | ARM Cortex-M4F 120 MHz | ARM Cortex-M4F 120 MHz | ARM Cortex-M4F 120 MHz | ARM Cortex-M4F 120 MHz |
| Flash Memory | 2 MB | 2 MB | 2 MB | 2 MB |
| SRAM Size | 640 KB | 640 KB | 640 KB | 1 MB |
| Display Interface | None on LQFP-144 | MIPI-DSI (yes) | MIPI-DSI (yes) | MIPI-DSI (yes) |
| Operating Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V |
| Shutdown Current | 33 nA | 33 nA | 33 nA | 33 nA |
| USB OTG | Yes (FS, internal PHY) | Yes (FS, internal PHY) | Yes (FS, internal PHY) | Yes (FS, internal PHY) |
Principaux différenciateurs
- 2 MB Flash with Cortex-M4F at 120 MHz and FPU/DSP in LQFP-144 (vs STM32L4R5ZGT6)
- MIPI-DSI absent on ZIT6 vs available on R7ZIT6 same-family upgrade (vs STM32L4R7ZIT6)
- Cortex-M4F DSP and FPU in LQFP-144 same footprint as Cortex-M3 GD32F103 (vs GD32F103)
Notes de conception
The STM32L4R5ZIT6 supports two voltage-regulation modes: direct LDO and internal SMPS step-down converter. For ultra-low-power battery designs (1.71 V - 2.0 V), use the SMPS mode to reduce Run-mode current by ~50% compared to LDO. Estimated: SMPS external inductor 10 µH (XAL4030 or similar) and 4.7 µF X7R input/output capacitor per AN4621. Add a 100 nF decoupling capacitor on every VDD/VDDA pin pair to suppress high-frequency switching noise.
Layout: place the 32.768 kHz crystal (LSE) within 5 mm of PC14/PC15 with short traces and guard ring for noise immunity. Keep USB DP/DM traces length-matched to within 2 mm and 90 ohm differential impedance per USB 2.0 full-speed requirements. Decouple each VDD pin with 100 nF X7R placed within 2 mm, plus 4.7 µF bulk capacitors at each regulator pin. The LQFP-144 thermal pad handling follows ST's AN5036 PCB design guide.
Many STM32L4 firmware delays stem from failing to set the ART Accelerator prefetch buffer and Flash wait states for 120 MHz operation - both must be configured in SystemInit() before raising the clock. RTC date/time must be in BCD format (not BINARY) unless explicitly using STM32Cube HAL. When entering Shutdown mode, the LSE crystal must remain enabled if RTC wake-up is required, otherwise wake from WAKEUP pins only. Estimated: at 120 MHz with 3.3 V VDD, Run-mode current is approximately 5 mA; going to Stop 2 mode reduces this to ~1.1 µA retaining RTC.
To meet industrial EMI/EMC standards (EN 55022 Class B), place a ferrite bead (600 ohm at 100 MHz) on each VDD rail and use a 4-layer PCB with a continuous ground plane. Spread-spectrum clocking on HSE can be enabled to reduce peak emissions by 4-8 dB per AN2867. Keep GPIO toggle paths away from analog ADC traces; route analog and digital grounds separately back to a single star ground at the AGND/VDDA decoupling capacitor.
Informations de conformité
RoHS compliant per ST product page. Industrial temperature range -40C to +85C (grade 6) or -40C to +125C (grade 7). Not AEC-Q100 qualified - for automotive applications use STM32L4R5ZIT6Q variant.
