STM32L4R5ZIT6 - 32-bit ARM Cortex-M4 MCU 120MHz 2MB Flash LQFP-144 | STMicroelectronics
부품 번호: STM32L4R5ZIT6 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.4 | $164.00 |
| 100 | $14.2 | $1,420.00 |
| 500 | $12.85 | $6,425.00 |
| 1,000 | $11.4 | $11,400.00 |
STM32L4R5ZIT6 개요
An ARM Cortex-M4 microcontroller (MCU) is a 32-bit RISC processor core designed by Arm Holdings for embedded applications. It combines high computational performance with low power consumption, and the M4 variant adds a single-precision floating-point unit (FPU) plus DSP extensions. In the broader taxonomy, the STM32L4R5 belongs to the ultra-low-power microcontroller family (STM32L series), which sits below the mainstream STM32F series and above the ultra-low-power STM32L0 in ST's power-versus-performance spectrum. The "plus" designation (STM32L4+) indicates the higher-performance 120 MHz sub-family with Chrom-GRC graphics support.
Key features of the STM32L4R5ZIT6 include a FlexPowerControl architecture with multiple low-power modes (Shutdown at 33 nA, VBAT mode at 305 nA, Batch Acquisition Mode for partial wake-up), USB OTG with internal PHY, and a DFSDM (Digital Filter for Sigma-Delta Modulators) peripheral for sensor hub applications. It also features a Chrom-ART Accelerator for 2D graphics and an Octo-SPI interface for high-speed external Flash, along with cryptographic and AES-256 hardware accelerators for IoT security.
The device integrates the Cortex-M4 core with FPU and Memory Protection Unit, plus ST's ART Accelerator (Adaptive Real-Time memory accelerator) that allows 0-wait-state execution from Flash at the full 120 MHz clock speed. Up to 640 KB SRAM includes 32 KB of SRAM2 with parity check, retained in Standby mode and accessible via SRAM-based boot for secure firmware update. The LQFP-144 package exposes the full STM32L4R5 peripheral set: 3x 12-bit ADC (16-bit with oversampling), 2x DAC, 4x op-amps, 2x comparators, multiple timers, TFT controller, and MIPI-DSI support requires the larger BGA package.
Typical applications include wearable health monitors, smart sensors, IoT edge nodes, industrial HMI panels, low-power wireless modules (BLE/LoRa companion), battery-powered data loggers, and energy-harvesting systems. The 2 MB Flash supports over-the-air firmware updates and rich graphical user interfaces on small TFT displays without external memory.
When designing with the STM32L4R5ZIT6, use ST's STM32CubeMX and STM32CubeIDE toolchain for code generation, pin multiplexing, and power-consumption profiling. Source decoupling requires 100 nF X7R ceramic on every VDD/VDDA pair; the integrated SMPS step-down converter (when present on L4+ variants) should be configured with a 10 µH inductor per the application note AN4621. The LQFP-144 thermal performance typically permits 500 mA peak current draw at 120 MHz with a 2-layer FR4 board.
This page synthesizes distributor pricing tiers, drop-in compatible same-family STM32 alternatives, application-tailored companion MPNs, and practical low-power design guidance that complements the manufacturer datasheet.
드롭인 대체품: STM32L4R5ZIT6 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: STM32L4R5ZIT6 (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC, Core, DAC, Graphics Accelerator.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
STM32L4R7ZIT6
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
STM32L4S5ZIT6
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
STM32L4R5ZIT6P
✅ 드롭인✓ 재고 있음
$9.3 / 개
데이터시트 보기 →STM32L4R5ZGT6
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
STM32L4R9ZIT6
✅ 드롭인✓ 재고 있음
$7.2 / 개
데이터시트 보기 →STM32L4R5ZIT6 최대 정격 & 전기적 특성
| Core | ARM Cortex-M4 with FPU |
| 최대 클록 주파수 | 120 MHz |
| Performance | 150 DMIPS / 273 CoreMark |
| Program Memory Size | 2 MB (2 M x 8) Flash |
| RAM Size | 640 KB |
| Supply Voltage Range | 1.71 V to 3.6 V |
| 동작 온도 범위 | -40 °C to +85 °C (grade 6), -40 °C to +125 °C (grade 7) |
| 패키지 | 144-LQFP (20 x 20 mm) |
| 핀 수 | 144 |
| 실장 유형 | Surface Mount |
| ADC | 3 x 12-bit (up to 16-bit with hardware oversampling) |
| DAC | 2 x 12-bit |
| USB | USB OTG Full-Speed with internal PHY |
| Low-Power Modes | Shutdown 33 nA, VBAT mode 305 nA, Standby with RTC |
| External Memory Bus | Octo-SPI, FMC, SDMMC |
| MSL 레벨 | 3 (168 hours) |
| RoHS 상태 | Compliant |
STM32L4R5ZIT6 핀 구성
| 핀 1 | PE2 — GPIO PE2, TRACECLK |
| 핀 2 | PE3 — GPIO PE3, TRACED0 |
| 핀 3 | PE4 — GPIO PE4, TRACED1 |
| 핀 4 | PE5 — GPIO PE5, TRACED2 |
| 핀 5 | PE6 — GPIO PE6, TRACED3 |
| 핀 6 | VBAT — RTC backup power supply |
| 핀 7 | PC13 — GPIO PC13 (Tamper-RTC) |
| 핀 8 | PC14 — GPIO PC14 / OSC32_IN |
| 핀 9 | PC15 — GPIO PC15 / OSC32_OUT |
| 핀 10 | VSS — Ground |
| 핀 11 | VDD — Digital supply voltage |
| 핀 12 | PH0 — GPIO PH0 / OSC_IN |
| 핀 13 | PH1 — GPIO PH1 / OSC_OUT |
| 핀 14 | NRST — Reset input (active low) |
| 핀 15 | PC0 — GPIO PC0, ADC1_IN6 |
| 핀 16 | PC1 — GPIO PC1, ADC1_IN7 |
| 핀 17 | PC2 — GPIO PC2, ADC1_IN8 |
| 핀 18 | PC3 — GPIO PC3, ADC1_IN9 |
| 핀 19 | VSSA — Analog ground |
| 핀 20 | VDDA — Analog supply voltage |
| 핀 21 | PA0 — GPIO PA0, ADC1_IN5, UART4_TX |
| 핀 22 | PA1 — GPIO PA1, ADC1_IN6, UART4_RX |
| 핀 23 | PA2 — GPIO PA2, USART2_TX |
| 핀 24 | PA3 — GPIO PA3, USART2_RX |
| 핀 25 | VSS — Ground |
| 핀 26 | VDD — Digital supply voltage |
| 핀 27 | PA4 — GPIO PA4, SPI1_NSS, DAC_OUT1 |
| 핀 28 | PA5 — GPIO PA5, SPI1_SCK, DAC_OUT2 |
| 핀 29 | PA6 — GPIO PA6, SPI1_MISO, ADC1_IN11 |
| 핀 30 | PA7 — GPIO PA7, SPI1_MOSI, ADC1_IN12 |
| 핀 31 | PC4 — GPIO PC4, ADC1_IN13 |
| 핀 32 | PC5 — GPIO PC5, ADC1_IN14 |
| 핀 33 | PB0 — GPIO PB0, ADC1_IN15, TIM3_CH3 |
| 핀 34 | PB1 — GPIO PB1, ADC1_IN16, TIM3_CH4 |
| 핀 35 | PB2 — GPIO PB2, BOOT1 |
| 핀 36 | PE7 — GPIO PE7 |
| 핀 37 | PE8 — GPIO PE8 |
| 핀 38 | PE9 — GPIO PE9 |
| 핀 39 | PE10 — GPIO PE10 |
| 핀 40 | PE11 — GPIO PE11 |
| 핀 41 | PE12 — GPIO PE12 |
| 핀 42 | PE13 — GPIO PE13 |
| 핀 43 | PE14 — GPIO PE14 |
| 핀 44 | PE15 — GPIO PE15 |
| 핀 45 | PB10 — GPIO PB10, I2C2_SCL, USART3_TX |
| 핀 46 | PB11 — GPIO PB11, I2C2_SDA, USART3_RX |
| 핀 47 | VSS — Ground |
| 핀 48 | VDD — Digital supply voltage |
| 핀 49 | PB12 — GPIO PB12, SPI2_NSS, TIM1_BKIN |
| 핀 50 | PB13 — GPIO PB13, SPI2_SCK, USART3_CTS |
| 핀 51 | PB14 — GPIO PB14, SPI2_MISO, USART3_RTS |
| 핀 52 | PB15 — GPIO PB15, SPI2_MOSI, TIM1_CH3N |
| 핀 53 | PD8 — GPIO PD8 |
| 핀 54 | PD9 — GPIO PD9 |
| 핀 55 | PD10 — GPIO PD10 |
| 핀 56 | PD11 — GPIO PD11 |
| 핀 57 | PD12 — GPIO PD12 |
| 핀 58 | PD13 — GPIO PD13 |
| 핀 59 | PD14 — GPIO PD14 |
| 핀 60 | PD15 — GPIO PD15 |
| 핀 61 | PC6 — GPIO PC6, USART6_TX, TIM3_CH1 |
| 핀 62 | PC7 — GPIO PC7, USART6_RX, TIM3_CH2 |
| 핀 63 | PC8 — GPIO PC8, SDMMC_D0, TIM3_CH3 |
| 핀 64 | PC9 — GPIO PC9, SDMMC_D1, TIM3_CH4 |
| 핀 65 | PA8 — GPIO PA8, USART1_CK, TIM1_CH1, MCO |
| 핀 66 | PA9 — GPIO PA9, USART1_TX, TIM1_CH2 |
| 핀 67 | PA10 — GPIO PA10, USART1_RX, TIM1_CH3 |
| 핀 68 | PA11 — GPIO PA11, USB_OTG_FS_DM |
| 핀 69 | PA12 — GPIO PA12, USB_OTG_FS_DP |
| 핀 70 | PA13 — GPIO PA13, SWDIO |
| 핀 71 | PA14 — GPIO PA14, SWCLK |
| 핀 72 | PA15 — GPIO PA15, SPI1_NSS, TIM2_CH1 |
| 핀 73 | PC10 — GPIO PC10, USART3_TX, SDMMC_D2 |
| 핀 74 | PC11 — GPIO PC11, USART3_RX, SDMMC_D3 |
| 핀 75 | PC12 — GPIO PC12, USART3_CK, SDMMC_CK |
| 핀 76 | PD0 — GPIO PD0, CAN1_RX, FMC_D2 |
| 핀 77 | PD1 — GPIO PD1, CAN1_TX, FMC_D3 |
| 핀 78 | PD2 — GPIO PD2, SDMMC_CMD, TIM3_ETR |
| 핀 79 | PD3 — GPIO PD3, USART2_CTS, FMC_CLK |
| 핀 80 | PD4 — GPIO PD4, USART2_RTS, FMC_NOE |
| 핀 81 | PD5 — GPIO PD5, USART2_TX, FMC_NWE |
| 핀 82 | VSS — Ground |
| 핀 83 | VDD — Digital supply voltage |
| 핀 84 | PD6 — GPIO PD6, USART2_RX, FMC_NWAIT |
| 핀 85 | PD7 — GPIO PD7, USART2_CK, FMC_NE1 |
| 핀 86 | PB3 — GPIO PB3, SPI1_SCK, TIM2_CH2 |
| 핀 87 | PB4 — GPIO PB4, SPI1_MISO, TIM3_CH1 |
| 핀 88 | PB5 — GPIO PB5, SPI1_MOSI, I2C1_SMBA, TIM3_CH2 |
| 핀 89 | PB6 — GPIO PB6, I2C1_SCL, USART1_TX |
| 핀 90 | PB7 — GPIO PB7, I2C1_SDA, USART1_RX |
| 핀 91 | BOOT0 — Boot mode select |
| 핀 92 | PB8 — GPIO PB8, I2C1_SCL, TIM4_CH3 |
| 핀 93 | PB9 — GPIO PB9, I2C1_SDA, TIM4_CH4 |
| 핀 94 | PE0 — GPIO PE0, TIM4_ETR |
| 핀 95 | PE1 — GPIO PE1 |
| 핀 96 | VSS — Ground |
| 핀 97 | VDD — Digital supply voltage |
| 핀 98 | PF6 — GPIO PF6, TIM5_CH1, ADC3_IN4 |
| 핀 99 | PF7 — GPIO PF7, TIM5_CH2, ADC3_IN5 |
| 핀 100 | PF8 — GPIO PF8, TIM5_CH3, ADC3_IN6 |
| 핀 101 | PF9 — GPIO PF9, TIM5_CH4, ADC3_IN7 |
| 핀 102 | PF10 — GPIO PF10, ADC3_IN8 |
| 핀 103 | PF11 — GPIO PF11, ADC3_IN9 |
| 핀 104 | VSS — Ground |
| 핀 105 | VDD — Digital supply voltage |
| 핀 106 | PF12 — GPIO PF12, FSMC_A6 |
| 핀 107 | PF13 — GPIO PF13, FSMC_A7 |
| 핀 108 | PF14 — GPIO PF14, FSMC_A8 |
| 핀 109 | PF15 — GPIO PF15, FSMC_A9 |
| 핀 110 | PG0 — GPIO PG0, FSMC_A10 |
| 핀 111 | PG1 — GPIO PG1, FSMC_A11 |
| 핀 112 | PE2 — GPIO PE2, TRACECLK (alt) |
| 핀 113 | PE3 — GPIO PE3, TRACED0 (alt) |
| 핀 114 | PE4 — GPIO PE4, TRACED1 (alt) |
| 핀 115 | PE5 — GPIO PE5, TRACED2 (alt) |
| 핀 116 | PG2 — GPIO PG2, FSMC_A12 |
| 핀 117 | PG3 — GPIO PG3, FSMC_A13 |
| 핀 118 | PG4 — GPIO PG4, FSMC_A14 |
| 핀 119 | PG5 — GPIO PG5, FSMC_A15 |
| 핀 120 | PG6 — GPIO PG6 |
| 핀 121 | PG7 — GPIO PG7 |
| 핀 122 | PG8 — GPIO PG8 |
| 핀 123 | VSS — Ground |
| 핀 124 | VDD — Digital supply voltage |
| 핀 125 | PG9 — GPIO PG9, USART6_RX, FSMC_NE3 |
| 핀 126 | PG10 — GPIO PG10, FSMC_NE4 |
| 핀 127 | PG11 — GPIO PG11, FSMC_A24 |
| 핀 128 | PG12 — GPIO PG12, FSMC_NE1 |
| 핀 129 | PG13 — GPIO PG13, FSMC_A26 |
| 핀 130 | PG14 — GPIO PG14, FSMC_A27 |
| 핀 131 | VSS — Ground |
| 핀 132 | VDD — Digital supply voltage |
| 핀 133 | PG15 — GPIO PG15 |
| 핀 134 | PB3 — GPIO PB3, JTDO, SPI1_SCK |
| 핀 135 | PB4 — GPIO PB4, NJTRST, SPI1_MISO |
| 핀 136 | PB5 — GPIO PB5, SPI1_MOSI |
| 핀 137 | PB6 — GPIO PB6, USART1_TX |
| 핀 138 | PB7 — GPIO PB7, USART1_RX |
| 핀 139 | PB8 — GPIO PB8, I2C1_SCL |
| 핀 140 | PB9 — GPIO PB9, I2C1_SDA |
| 핀 141 | PE0 — GPIO PE0, TIM4_ETR |
| 핀 142 | PE1 — GPIO PE1 |
| 핀 143 | VSS — Ground |
| 핀 144 | VDD — Digital supply voltage |
일반적인 애플리케이션
STM32L4R5ZIT6 적합 용도: 6 애플리케이션s: Wearable Health Monitor, Industrial HMI Control Panel, Battery-Powered IoT Sensor Hub, Smart Energy Metering, Medical Infusion Pump Controller, Smart Sensor Hub for Predictive Maintenance.
Wearable Health Monitor
The STM32L4R5ZIT6 fits wearable health monitors due to its Cortex-M4F at 120 MHz capable of running heart-rate and motion-fusion DSP, plus 33 nA Shutdown current for multi-day battery life. Placed as the system MCU between a Li-Po cell and the analog front-end, it directly drives PPG/AFE signal chains via the four integrated op-amps and three 12-bit ADCs. Compared to Cortex-M0/M0+ alternatives it provides DSP and FPU on the same footprint, enabling step-count and ECG-R-peak detection without external DSP. The 2 MB Flash supports over-the-air firmware updates while the 640 KB SRAM buffers minutes of raw sensor data for later BLE upload.
추천
Industrial HMI Control Panel
For industrial HMI panels, the STM32L4R5ZIT6 provides 120 MHz Cortex-M4 performance with Chrom-ART 2D acceleration to drive small TFT displays via SPI/8080 interfaces, plus FMC external bus for parallel memory expansion. Placed between the 24 V isolated supply and a 3.3 V LDO, it directly controls buttons, rotary encoders, and RS-485/Modbus via UART plus 50 MHz SPI. The 2 MB Flash hosts full graphics and a Chinese-English/Unicode character table. Compared to plain Cortex-M0 designs, the STM32L4R5ZIT6 renders multi-page interfaces without external SDRAM and supports Octo-SPI for faster TFT framebuffer access.
추천
Battery-Powered IoT Sensor Hub
The STM32L4R5ZIT6 enables coin-cell / 2xAA battery sensor hubs, with 33 nA Shutdown and 1.1 µA Stop 2 with RTC allowing multi-year coin-cell runtime per AN4621. Placed as the central controller for MEMS microphones, environmental sensors, and BLE hand-off, it integrates the DFSDM digital filter for sigma-delta microphones without a dedicated audio DSP. The 2 MB Flash supports LoRaWAN/BLE stacks and OTA updates without external memory. Compared to discrete Cortex-M0+ designs the STM32L4R5ZIT6 adds Cortex-M4F DSP and is rated 1.71 V to 3.6 V, ideal for energy harvesting.
추천
Smart Energy Metering
In smart energy meters, the STM32L4R5ZIT6 handles ADC sample aggregation, metrology DSP via Cortex-M4F MAC unit, and secure DLMS/COSEM firmware updates using its AES-256 hardware accelerator. Placed between the current-transformer / shunt front-end and the M-Bus / wireless PLC modem, it directly digitises up to three current channels with its 12-bit ADCs at oversampled 16-bit resolution. The 2 MB Flash holds protocol stacks for DLMS, M-Bus, and Wireless M-Bus plus regulatory firmware without external SPI flash. Compared to older Cortex-M3 designs, the STM32L4R5ZIT6 adds Standby 280 nA with RTC suitable for backup power modes.
추천
Medical Infusion Pump Controller
The STM32L4R5ZIT6 powers infusion pump controllers, with its Cortex-M4F running PID motor control loops, the 2 MB Flash hosting IEC 62304/60335-compliant firmware, and USB OTG enabling host-side data export. Placed between a stepper driver and the keypad/display, it handles stepper commutation via its advanced timers while the integrated op-amps condition pressure and bubble-detection sensors. The 640 KB SRAM accommodates pressure waveform buffers, while AES-256 protects dosing calibration data. Compared to Cortex-M3 designs, the FPU ensures deterministic real-time control loop execution and the L4+ low-leakage features suit battery-backup mode.
추천
Smart Sensor Hub for Predictive Maintenance
The STM32L4R5ZIT6 fits vibration and temperature sensor hubs in Industry 4.0, integrating the DFSDM digital filter for IEPE accelerometers and supporting FFT analysis via Cortex-M4F DSP with CMSIS-DSP library. Placed at industrial motor bearings, it runs self-powered from vibration energy harvesters thanks to 33 nA Shutdown and 1.71 V minimum supply. The 2 MB Flash hosts the wireless protocol stack (LoRa, BLE 5, or Wi-SUN) and predictive-maintenance ML models (TFLite-Micro). Compared to external-DSP designs, the single-chip integration reduces PCB area to under 20 mm square, which is decisive for retrofit-mount sensor units.
추천
추천 제품 요약
엔지니어링 참조 데이터: STM32L4R5ZIT6 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | STM32L4R7ZIT6 | STM32L4S5ZIT6 | STM32L4R9ZIT6 |
|---|---|---|---|---|
| Package | 144-LQFP (20x20) | 144-LQFP (20x20) | 144-LQFP (20x20) | 144-LQFP (20x20) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Core | ARM Cortex-M4F 120 MHz | ARM Cortex-M4F 120 MHz | ARM Cortex-M4F 120 MHz | ARM Cortex-M4F 120 MHz |
| Flash Memory | 2 MB | 2 MB | 2 MB | 2 MB |
| SRAM Size | 640 KB | 640 KB | 640 KB | 1 MB |
| Display Interface | None on LQFP-144 | MIPI-DSI (yes) | MIPI-DSI (yes) | MIPI-DSI (yes) |
| Operating Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V |
| Shutdown Current | 33 nA | 33 nA | 33 nA | 33 nA |
| USB OTG | Yes (FS, internal PHY) | Yes (FS, internal PHY) | Yes (FS, internal PHY) | Yes (FS, internal PHY) |
주요 차별점
- 2 MB Flash with Cortex-M4F at 120 MHz and FPU/DSP in LQFP-144 (vs STM32L4R5ZGT6)
- MIPI-DSI absent on ZIT6 vs available on R7ZIT6 same-family upgrade (vs STM32L4R7ZIT6)
- Cortex-M4F DSP and FPU in LQFP-144 same footprint as Cortex-M3 GD32F103 (vs GD32F103)
설계 노트
The STM32L4R5ZIT6 supports two voltage-regulation modes: direct LDO and internal SMPS step-down converter. For ultra-low-power battery designs (1.71 V - 2.0 V), use the SMPS mode to reduce Run-mode current by ~50% compared to LDO. Estimated: SMPS external inductor 10 µH (XAL4030 or similar) and 4.7 µF X7R input/output capacitor per AN4621. Add a 100 nF decoupling capacitor on every VDD/VDDA pin pair to suppress high-frequency switching noise.
Layout: place the 32.768 kHz crystal (LSE) within 5 mm of PC14/PC15 with short traces and guard ring for noise immunity. Keep USB DP/DM traces length-matched to within 2 mm and 90 ohm differential impedance per USB 2.0 full-speed requirements. Decouple each VDD pin with 100 nF X7R placed within 2 mm, plus 4.7 µF bulk capacitors at each regulator pin. The LQFP-144 thermal pad handling follows ST's AN5036 PCB design guide.
Many STM32L4 firmware delays stem from failing to set the ART Accelerator prefetch buffer and Flash wait states for 120 MHz operation - both must be configured in SystemInit() before raising the clock. RTC date/time must be in BCD format (not BINARY) unless explicitly using STM32Cube HAL. When entering Shutdown mode, the LSE crystal must remain enabled if RTC wake-up is required, otherwise wake from WAKEUP pins only. Estimated: at 120 MHz with 3.3 V VDD, Run-mode current is approximately 5 mA; going to Stop 2 mode reduces this to ~1.1 µA retaining RTC.
To meet industrial EMI/EMC standards (EN 55022 Class B), place a ferrite bead (600 ohm at 100 MHz) on each VDD rail and use a 4-layer PCB with a continuous ground plane. Spread-spectrum clocking on HSE can be enabled to reduce peak emissions by 4-8 dB per AN2867. Keep GPIO toggle paths away from analog ADC traces; route analog and digital grounds separately back to a single star ground at the AGND/VDDA decoupling capacitor.
규정 준수 정보
RoHS compliant per ST product page. Industrial temperature range -40C to +85C (grade 6) or -40C to +125C (grade 7). Not AEC-Q100 qualified - for automotive applications use STM32L4R5ZIT6Q variant.
